RAPID-RAIL Specifications

Transcription

1 RAPID-RAIL Specifications (Patent Pending) Complete Conveyor Systems and Equipment

2 Part Specifications (Patent Pending) Brackets Material Thickness Material 7 GA 304 Stainless Steel Pinion Material Thickness Material 12 GA 304 Stainless Steel Block Material High density polyethylene Shaft Dimensions Material ¾" outside diameter Stainless Steel square tube Mounting System Universal Joint Material Thickness Material Finish 12 GA Formed mild steel Formed 304 Stainless Steel Material Finish 303 Stainless Steel Machined finish Stardust silver powder coat paint #4 polish Adjustment Range Adjustment Types Layout Guidelines Single Sided Double Sided Hold Down Tolerance/Accuracy Repeatability 0.5" - 3.5" (Note: Product is NOT centered) 0.5" - 6.5" 3.5" - 9.5" 0.5" - 4.5" ± 1 /16" per side Opening ±⅛" Up to 6" of adjustment from smallest to largest product width ± 1 /32" per side 1 /16" overall Open rail to maximum then close to desired setting Manual Hand Wheel Motorized Discrete Controllers PLC Integrated System Siko System Etched bracket Siko actuator with pre-sets Digital display Configuration Up to 30 feet of adjustable rail per drive Up to 2 turns per drive Drives should be centrally located to the controlled rail Siko actuator(s) Ethernet IP PLC's HMI interface Siko actuator(s) Siko network Siko HMI Retrofit friendly Maintenance Guidelines Low maintenance design No lubrication needed 2

3 Part Specifications (Patent Pending) Product Compatibility Bottles Jars Cans Pouches Cartons Trays Cases Bundles Pucks Tubes PET Aseptic packaging Caps Tapered products Conveyor (Any Width) Compatibility Tabletop Mat-Style Belting Vacuum Airveyor Inclines Declines Turns: functions at any angle Horizontal Vertical Spiral Transfers Inline - Parallel Accumulating Rail Compatibility VGSSR round face VGSST 1¼" Tee Single high Double high VGSST 2¼" Tee Single high Other Most industry standard sheathed rails (Consult factory) Application Modes Installation Single Side Double Side Stacked Side Hold Down Combined Best value Widest adjustment range Side(s) and hold down Non-centering Product centering Types New equipment Difficult to access Remote locations Two independently adjustable rails on same side Shingling Tipping Accumulation 3

4 Part Specifications (Patent Pending) Standard Features Design 1. Powered (left) or hand crank wheel (right) adjustment 2. Torque limiter to prevent overloading system 3. Large flushable slots for washdown environments 4. Engraved bracket for guide rail opening reference 5. Linear slide bearing holds guide rail opening 6. Heavy duty ¾" square tube line shafts

5 Part Specifications (Patent Pending) Guide Rail Double Side Controlled Product Width Single Side Controlled Product Width Double High with Independent Control for Upper and Lower Rails Hold Down Powered Actuator Digital Programmable For individual line control Power design should be for 3 AMPS at 24 volts per acuator Sizing of wire is required by a qualified electrician Networkable For remotely controlling multiple units Power design should be for 3 AMPS at 24 volts per acuator Sizing of wire is required by a qualified electrician 5

6 Part Specifications (Patent Pending) Phaser Ring Design Features Allows for fine adjustment in rail openings Makes up for lags in u-joints Can adjust minor conveyor discrepancies Double High with Independent Control for Upper and Lower Rails Hold Down Inverted Guide Rail Brackets 6 Design Features Elevated line shaft Allows line shaft to extend over accessories added to frame Examples included motors, frames, and customer equipment

7 Maintenance Information 1. Pre-Start Checklist Fasteners - some may have loosened during shipment; re-tighten as required Inspect all splice points for proper alignment Check for proper product clearance prior to operation 2. Start-up/Break-in Daily monitoring of the following during the first 250 hours of operation Check guide rail timing - Spot check guide rail openings to make sure accuracy is maintained Check actuators - Check hand wheel or powered actuator for over torque. Adjust line shaft alignment if torque is too high 3. Control Basics Do NOT adjust rail when product is present Manual adjustment accomplished by use of hand wheel and scaled bracket Automatic adjustment accomplished by use of a HMI 4. Maintenance Maintenance is very low on this equipent Look for excessive wear Check for leaking seals on reducers Examine guide rail bracket blocks for disproportionate wear Semi-annual inspection of equipment is recommended for long life and exceptional operation 7

8 MODULAR CONVEYOR EXPRESS WARRANTY MODULAR CONVEYOR EXPRESS will repair or replace any products that have failed under normal use due to faulty material or defective workmanship for 1 year. Motors and chain carry the manufacturer's warranty. No other warranty is expressed or implied unless otherwise set forth in writing and approved by representative duly authorized to extend such approval by MODULAR CONVEYOR EXPRESS. All rights of design and invention are reserved. 1/3/2013 Modular Conveyor Express 600 S. Commercial Street Neenah, WI PH: Nercon Eng. & Mfg., Inc. All rights reserved. 01/ SPEC-RR ENVINK