Piranha 3D Hydro Plane
|
|
- Cecil Small
- 6 years ago
- Views:
Transcription
1 Piranha 3D Hydro Plane Dear customer, congratulations on the purchase of the Pirañha model. To enjoy building and flying the model most, please read carefully the building instructions before you begin and make sure that you understand the building process. Parts list Part name Pcs Part name Pcs Fuselage main part of EPP 2 Elevator and rudder interconnecting rods/bell 4 cranks Elevator control rod 2 Motor mount 3 Floats of EPP 2 Rudder arm 2 Elevator of EPP 1 Instructions 1 Vertical tail of EPP 2 Elevator arm 2 Rudder control rod 2 Fuselage 1 Auxiliary surfaces 2 Elevators connecting pieces 2 Rudder control bell crank 1 Doubler of the fuselage main part 1 You will need the following tools and materials: CA glue, CA glue accelerator, UHU POR can be used for some of the foam to foam joins, a sharp (modelling) knife, and sandpaper. To complete the model you need the following: a receiver (4ch), three servos (2x5.6g & 1x9g), an Brushless controller (10-12amp), a battery pack (3 LiPo cells of mah), a motor (HCS-80/2E or similar of about 80 W power output) Description of the model: The model is completely made of the EPP, strong enough to enable the Piranha to be used on the water, on the ground and in the air. Due to its revolutionary concept it gives the pilot the choice of pleasures among skimming above the ground or water surface or flying in the air. It is meant not only for experienced pilots, but also for modellers of average skill. You can power the Piranha with a brushless outrunner motor that has about 80W (or more) power & that weighs 35-45g, can be powered by 3 LiPo cells & an 8x4.3 or 8x4DD propeller. Thanks to the well thought out design you should be able to have this plane ready within 3-4 hours. Building the model: Unless otherwise stated, all parts are to be glued by the medium-thick CA glue. Start the building of the model by gluing both fuselage halves (Fig. 1). According to Fig. 2, cut a slit through the fuselage, then glue into it the glass fibre stiffener, using thin CA glue. If you have purchased an unpainted kit, you can paint it prior to construction, or after it is however easier to paint it before assembly. Make sure that you read through the instructions fully before painting to understand how it all fits together also note that the floats need trimming. Now glue the floats in place (Fig. 3) UHU POR is best for this, and sand their front parts to mate with the fuselage. If you plan to operate the model mainly on the water, devote a special attention to the surface finish of the floats. Spray on them the 3M contact glue and, once the glue slightly sets, apply the coloured self-adhesive tape to the surface. Crop the protruding part of the floats (Fig. 4). EPP on it s own is not waterproof & will need some protection if you are planning on using it on water. Glue the vertical tail surfaces along the bottom edge of the fuselage (Fig. 5) so that the hinge axes of both elevators and rudders are perpendicular. Then glue the top elevator in place (Fig. 6), ensuring at the same time that the elevator is parallel to the fuselage. According to the Fig. 7, glue the auxiliary fins in place, so that their rear edges end at the hinge point of the rudders Now glue together the motor mount according to the Figs. 8 and 9, ensuring the axis of the motor shaft is offset by some 3 to the right. It is best to also have a small amount of up thrust (ensure that there is no down thrust, this will prevent your piranha from flying!). Using a sharp knife, cut a 10 mm deep slit in the fuselage parallel to the fuselage axis and glue the assembled motor mount in place (Fig. 10). Glue the servos carefully by their mounting flanges and secure them. It is a good idea to wrap the servos with tape before gluing (masking tape or pvc tape both work fine) this prevents glue entering the servo & also makes it easier to remove the servo in the future should you need to (Fig. 11). If you are planning to use the Piranha on water, you can waterproof the speed controller by sealing the ends carefully with hot glue or a small amount of silicon sealant. Using the Fig.12 as a guide, glue the controller to the motor bulkhead (it is possible to attach it with a Velcro strip or cable tie). Bolt the motor flange in place and secure the motor. Using the five-minute epoxy, glue the rudder servo arm (bell crank) to the rudder servo (Fig. 13). The receiver may be also waterproofed by inserting it into a rubber balloon and tying the end (this measure would ensure complete waterproofing of the model). Then glue the fuselage top to its lower (float) part. Glue the V-shaped bell cranks into the rudders (Fig. 14). Now finish the model using any spray paint (the EPP does not degrade from any spray-can paint, enamel spray paint works very well). Piranha build manual page: 1 / 5
2 Install the rudder control rods (Fig. 15). Glue the cross-shaped braces of aluminium wire (Fig. 16) according to the detailed drawing on the Figs. 17 and 18. Glue the elevator arm in place (Fig 19) and install the control rods (Fig. 20). Cut slits in the elevators and insert the connector levers to them (Fig. 21). Using the interconnection rods, joint the upper and lower elevators (Fig. 22), checking and ensuring, that the control surfaces are in a neutral position!! Final steps - the model is built. Now check the position of the centre of gravity (CG), which should be 291 mm from the model s nose. By moving the C of G. to the rear, the model becomes more nimble (therefore this modification is recommended to the more experienced pilots only)) and vice versa the more the C of G forward, the more stable is the model. For the initial flights, set the control surface deflection to about 50 %; the elevator servos should be programmed for a delta-winged model (elevon mixing). The rudders serve mainly to control the direction of movement on the surface (both ground and water), but they are effective also in the air. The properly balanced model takes-off in a few metres. Bear in mind, please, that when throttling back, the model does not glide, it sort of sags to ground. If throttled back in horizontal flight attitude, the Piranha lands by itself. The recommended equipment: Battery pack 3s1p 640 mah (Kokam) Motor choice: HCS C 80W/2, HCS23/8/12E, Hyperion 2209 (26 or 32), AXI 2208/34 motor or similar Motor mount you may wish to use a tube type motor mount instead of the included one. GWS 8x4 Direct Drive propeller Castle Creations Phoenix 10 brushless speed controller, Hyperion Titan 10 or equivalent. This model is not a toy therefore avoid flying in crowded places or such areas where you may cause damage/injury to yourself, others or their property. Lots of fun and many happy landings Robotbirds.com Piranha build manual page: 2 / 5
3 Piranha build manual page: 3 / 5
4 Piranha build manual page: 4 / 5
5 Piranha build manual page: 5 / 5
STORCH. Parts. Additional items needed to complete the Storch
STORCH Parts Fuse with Greenhouse- (Attached) Left and right wing panel Horizontal and vertical stab 2 Wing center blocks 2 Carbon spares for wing 1 Undercarriage with wheels 2 Undercarriage shocks 2 Carbon
More informationMEMO. No.4341 Specification: Wing Span: 29.1 (740mm) Length: 36.6 (930mm) 2. Warranty
MEMO No.4341 Specification: Wing Span: 29.1 (740mm) Length: 36.6 (930mm) 2 Wing Area: 299 sq.in. (19.29 dm ) Weight: 18.9oz. (536.5g) 2 Wing loading: 0.58 oz./sq.ft (27.8g/dm ) Motor: OBL 29/27-07A Warranty
More informationAssembly and Operating Manual HR-100. Specification: *Length: 41-7/10"(1060 mm) *Wing span: 49-1/5"(1250 mm) *Flying weight: 45.
Assembly and Operating Manual HR-100 Specification: *Length: 41-7/10"(1060 mm) *Wing span: 49-1/5"(1250 mm) *Flying weight: 45.9 oz (1300g) Dear customer, Congratulations on your choice of a factory-assembled
More informationESPA3D Photo Essay One page ESPA3D Plans are HERE Back to Spad Plans Index
1 of 8 8/29/2012 12:28 PM ESPA3D Photo Essay One page ESPA3D Plans are HERE Back to Spad Plans Index This little airplane has turned out to be one of the most fun Spad projects we've ever done! It is built
More informationElectric or I/C. Velocity
Electric or I/C Velocity This, the latest in the Weston UK range of hyper performance ARTF kits, has been developed over a period of years to provide the ultimate flight performance. PLEASE NOTE: THIS
More informationALMOST READY TO FLY. Wing Span in cm. 2
ASSEMBLY MANUAL ALMOST READY TO FLY MS:X9 Specifications Wing Span --------------------------61.4 in ---------------------------156cm. 2 Wing Area --------------------------606.1 sq.in ------------------
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 6000mm (236.2 in) - Length: 2873mm (113.1 in) - Flying weight: 14-18 kg - Wing area: 219.4 dm2 - Wing loading: 64g/dm2 - Wing type: HQ airfoils - Covering type: Genuine ORACOVER
More informationYAK 54 Aerobatic Model Aircraft Assembly and Instruction Manual
YAK 54 Aerobatic Model Aircraft Assembly and Instruction Manual Warning: This radio controlled model is not a toy. It requires skill to fly and is not recommended for the novice pilot. It should not be
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1404mm (55.3in) - Length: 1134mm (44. 6 in) - Flying weight: 3.2-3.4 kg - Covering type: Genuine ORACOVER - Spinner size: scale type (not included) - Radio: 4 channel minimum
More informationRADIO CONTROL MODEL ASSEMBLY INSTRUCTIONS. Wasp
RADIO CONTROL MODEL ASSEMBLY INSTRUCTIONS Wasp TRAINER Almost ready-to-fly Wingspan 1520mm Fuselage length 1105mm Engine: 40-46 2T / 52-60 4T Electric Motor: 600-700W Radio: 5 channel / 4-5 servo RC Functions:
More informationAssembly and Operating Manual. 3D cap-232. Specification: *Length: 25-9/10"(655mm) *Wing Span: 29-3/5"(750mm) *Flying Weight: 15-9/10 oz (450g)
Assembly and Operating Manual 3D cap-232 Specification: *Length: 25-9/10"(655mm) *Wing Span: 29-3/5"(750mm) *Flying Weight: 15-9/10 oz (450g) Dear customer, Congratulations on your choice of a factory-assembled
More information48in Sbach-342. Instruction Manual. Specifications
48in Sbach-342 Instruction Manual Specifications Wingspan: 48in (1219mm) Length: 46in (1163mm) Wing Area: 471sq in (30.4sq dm) Flying Weight: 1.8-2.0lb (800-900g) Dear Customer, www.valuehobby.com/48in-s342-arf.html
More informationInstruction Manual. We wish you many enjoyable flights with your plane and once again thank you for your choosing a Phoenix Model product
Instruction Manual Wing span: 1590mm (626 in) Length: 1100mm (433 in) Weight: 1500gr - 1700gr Motor: AXI 2814/10 or Motor: 500-600 w/ gear box Radio: 4 Channel / 4 servos standar Propeller: 12 x 47 We
More informationI n s t r u c t i o n M a n u a l. Instruction Manual SPECIFICATION
I n s t r u c t i o n M a n u a l Instruction Manual SPECIFICATION - Wingspan: 3200mm (125,9 in) - Length: 1650mm (64,9 in) - Flying weight: 3000gr 3200gr - Wing area: 64.5 dm2 - Wing loading: 46g/dm2
More informationTrainer Assembly Manual
Trainer Assembly Manual www.pilot-rc.com -Pilot Trainer- 1 -Pilot Trainer- 2 -Pilot Trainer- 3 -Preliminary i wing & stab assembly- 1-) Locate both Plywood wing joiners (Large and small one) 2-) Insert
More informationAssembly and Operating Manual. SPECIFICATION Length inch (640mm) Wing Span inch (705mm) Flying Weight oz (330g)
Assembly and Operating Manual SPECIFICATION Length 25.19 inch (640mm) Wing Span 27.76 inch (705mm) Flying Weight 11.64 oz (330g) Dear customer, Assembly and Operating manual VIPER The Radio Control System
More informationInstruction Manual book
book ITEM CODE:BH 115. SPECIFICATION Wingspan : 6,000 mm 236,22 in. Length : 2,740 mm 107,87 in. Weight : 17.5kg 38.5Lbs. Radio : 08 channels. Servo : 07-08 HS-5685MH(HITEC) Battery : 2 Cells-Li-Po 7.4V
More informationGent EPP. Before use please read the explanations carefully
Before use please read the explanations carefully Gent EPP Instruction Manual Specifications Fuselage length 900mm 35in Wingspan 820mm 32in Flying Weight 210 240g with battery Additional Required Equipment
More informationSIZE.120 OR 30CC SCALE 1:5 ARF
PC21 PILATUS MK2 SIZE.120 OR 30CC SCALE 1:5 ARF SPECIFICATION - Wingspan: 1772mm (69.72in) - Length: 2019mm (79.5 in) - Flying weight: 6.4-7.2 kg - Wing area: 57.6 dm2 - Wing loading: 113g/dm2 - Wing type:
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1410mm (55.5 in) - Length: 1278mm (50.3 in) - Flying weight: 3.2-3.4 kg - Wing area: 41.3 dm2 - Wing loading: 75g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationInstruction Manual book
Instruction Manual book ITEM CODE:BH118. SPECIFICATION Wingspan : 1,050 mm 41.34 inches. Length : 950mm 37.4 inches. Weight : 1 kg 2.2 lbs. Radio : 04 channels. Servo : 4 mini servos. Motor : KMS 2814/05
More informationMARACANA ASSEMBLY INSTRUCTION .40 ARF LOW WING TRAINER RADIO CONTROL MODEL. Every body can fly
RADIO CONTROL MODEL ASSEMBLY INSTRUCTION MARACANA.40 ARF LOW WING TRAINER Every body can fly VQA085 EP GP You can use both Gas or Electric power Wingspan: 59in.(1520mm) Fuselage length: 48in.(1220mm) Engine:
More information8mm EPP Acrocub. Instruction Manual. Specifications
8mm EPP Acrocub Instruction Manual Specifications Wingspan: 34.6 in (880mm) Length: 31.5 in (800mm) Wing Area: 213.9 sq in (13.8sq dm) Flying Weight: Approx. 9oz (270g) Dear Customer, www.valuehobby.com/8mm-epp-acrocub.html
More informationPlease read all instructions carefully before assembly and flight!
Please read all instructions carefully before assembly and flight! Thank you for purchasing the Mig-15. This model is designed for the intermediate to advanced flyer. The model is receiver ready and includes
More informationMS:159 ASSEMBLY MANUAL. Graphics and specifications may change without notice.
ASSEMBLY MANUAL MS:159 Graphics and specifications may change without notice. Specifications: Wing span ----------------------------61.8in (157cm). Wing area -----------------1100.5sq.in (71.0sq dm). Weight
More informationASSEMBLY MANUAL. Kit features. MS:110
MS:110 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span-------------------------------------------------- 62.9 in---------------------------------------
More informationTurbinator-2 Build Manual
Turbinator-2 Build Manual Thank you for your purchase of the Turbinator-2 sport jet by Boomerang RC Jets. This RC Jet IS NOT A TOY and should only be flown and operated by experienced RC Turbine Pilots.
More informationH-King R/C scale model series. instruction manual
H-King R/C scale model series instruction manual 1. Please read this manual carefully and follow the instructions of the manual before you use this products. SAFETY INSTRUCTIONS 2. Our airplane is not
More information35MM Series Nano F15. Assembly and Operating Manual
35MM Series 2011 Assembly and Operating Manual SPECIFICATION: Length: 21-3/5"(550mm) Wing Span: 15-3/5"(395mm) Flying Weight: 5-4/5oz (165g.) Nano F15 Dear customer, Congratulations on your choice of a
More informationSTICK F Class 60 Class INSTRUCTION MANUAL. Or Electric equivalent. (2T engine) (4T engine) Radio control model SPECIFICATIONS
Radio control model 45 Class 60 Class (2T engine) (4T engine) Or Electric equivalent INSTRUCTION MANUAL STICK F - 1500 SPECIFICATIONS Wingspan 60 in. Length 38.5 in. Electric Motor 650 Watt Glow Engine.45
More informationPITTS 12 R/C SPORT-SCALE AIRCRAFT ASSEMBLY AND INSTRUCTION MANUAL. Copyright Century UK Limited 2012
PITTS 12 R/C SPORT-SCALE AIRCRAFT ASSEMBLY AND INSTRUCTION MANUAL 1 Warning: This radio controlled model is not a toy. It requires skill to fly and is not recommended for use by beginners. It should not
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1600mm (63 in) - Length: 1285mm (50.5 in) - Flying weight: 2800-3200 gr - Wing area: 40.1 dm2 - Wing loading: 78g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More information51in Aerobatic Series Sukhoi SU-26M Almost-Ready-to-Fly. Instruction Manual. Specifications
51in Aerobatic Series Sukhoi SU-26M Almost-Ready-to-Fly Instruction Manual Specifications Wingspan: 51.2 in (1300mm) Length: 51.2 in (1300mm) Wing Area: 581 sq in (37.5sq dm) Flying Weight: 3.5 lb (1600g)
More informationInstruction Manual EXTRA 260-EP. 1075mm (42.32 in) 1000mm (39.37 in) 1100gr gr. 4 channel - 4 mini servo. Axi motor 2820
1075mm (42.32 in) 1000mm (39.37 in) 1100gr - 1400gr 4 channel - 4 mini servo Axi motor 2820 KIT CONTENTS: We have organized the parts as they come out of the box for better identification during assembly.
More informationAssembly and Operating Manual
Assembly and Operating Manual SCREAMER Specification: *Length: 20"(510 mm) *Wing span: 22 4/5"(580 mm) *Flying weight: 10 4/5 oz (305g) Dear customer, Congratulations on your choice of a factory-assembled
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 2000mm (78.7in) - Length: 1544mm (60.7 in) - Flying weight: 3600-3800 gr - Wing area: 66 dm2 - Wing loading: 55g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationAssembly and Operating Manual
Assembly and Operating Manual Dear customer, Congratulations on your choice of a factory-assembled model aircraft from the SKYANGEL Hummingbird range and thank you for placing your trust in us. Very little
More informationALMOST READY TO FLY. Wing Span in cm. 2
ASSEMBLY MANUAL ALMOST READY TO FLY MS: X12 A - B Graphics and specfications may change without notice. Kit features. Specifications Wing Span ------------------------------- 42.7 in ---------------------
More informationSBACH SCALE 1:4 ½ ARF
SPECIFICATION - Wingspan: 1663mm (65.5 in) - Length: 1638mm (64.5 in) - Flying weight: 4700-5200 gr - Wing area: 56 dm2 - Wing loading: 85g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationPlease read all instructions carefully before assembly and flight!
c c Please read all instructions carefully before assembly and flight! Thank you for purchasing the. This model is designed for the intermediate to advanced flyer. The model is receiver-ready and includes
More informationAssembly and Operating Manual
Dear customer, Assembly and Operating Manual The radio control system Glued joints, suitable adhesives Congratulations on your choice of a factory-assembled model aircraft from the SKYANGEL Hummingbird
More informationAssembly and operating instructions. Assembly and Operating Manual
Assembly and operating instructions Assembly and Operating Manual Dear customer, Assembly and Operating Manual The radio control system Glued joints, suitable adhesives Congratulations on your choice of
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1800mm (70.8 in) - Length: 1355mm (53.3 in) - Flying weight: 4100-4300 g - Wing area: 51 dm2 - Wing loading: 80g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationInstruction Manual book
Instruction Manual book ITEM CODE:BH118. SPECIFICATION Wingspan : 1,050 mm 41.34 inches. Length : 950mm 37.4 inches. Weight : 1 kg 2.2 lbs. Radio : 04 channels. Servo : 4 mini servos. Motor : BL2215/20
More informationMEMO. Assembly Manual. No Specification: Wing Span: 29.3 (830mm) Length: 29.8 (845mm) 2. Warranty
MEMO Assembly Manual No. 4347 Specification: Wing Span: 29.3 (830mm) Length: 29.8 (845mm) 2 Wing Area: 322.4 sq.in. (20.8 dm ) Weight: 14oz.~15oz. (420~430g) Warranty This kit is guaranteed to be free
More informationAssembly and operating instructions. Assembly and Operating Manual
Assembly and operating instructions Assembly and Operating Manual Dear customer, Assembly and Operating Manual The radio control system Glued joints, suitable adhesives Congratulations on your choice of
More informationMEMO. Assembly Manual. No Specification: Wing Span: 29.3 (830mm) Length: 29.8 (845mm) 2. Warranty
MEMO Assembly Manual No. 4347 Specification: Wing Span: 29.3 (830mm) Length: 29.8 (845mm) 2 Wing Area: 322.4 sq.in. (20.8 dm ) Weight: 14oz.~15oz. (420~430g) Warranty This kit is guaranteed to be free
More information96in Super Decathlon ARF
96in Super Decathlon ARF Instruction Manual Specifications Wingspan: 96in (2438mm) Length: 63.5 in (1614mm) Weight: Approx. 13lbs (6.5kg) 1 Dear Customer, Congratulations on your purchase of Super Decathlon
More informationI/C FLIGHT GUIDELINES
SPECIFICATION - Wingspan: 3500mm (137.8 in) - Length: 1650mm (64.96 in) - Flying weight: 3700-4000 gr - Wing area: 75 dm2 - Wing loading: 49g/dm2 - Wing type: HQ profile - Covering type: Genuine ORACOVER
More informationF3P Instruction Manual
Before use, please read the explanations carefully! F3P Instruction Manual Specifications Fuselage length: 884mm ( 34. Bin ) Wingspan : 845mm ( 33. 2in) Flying Weight : 135-160g (with battery) Additional
More informationInstruction Manual MUSTANG P51 - EP. Wingspan : 1377mm (54.21in) : 1180mm (46.46 in) : 2200gr gr. : AXI motor 2826 or 4120
Instruction Manual MUSTANG P51 - EP Wingspan : 1377mm (54.21in) g Length : 1180mm (46.46 in) Weight : 2200gr - 2600gr Engine : AXI motor 2826 or 4120 Radio : 4 channel / 4 servos standard KIT CONTENTS:
More informationASSEMBLY MANUAL. Kit features. MS:76
ASSEMBLY MANUAL MS:76 Graphics and specfications may change without notice. Specifications: Wingspan---------------------------------------------------- 82.8 in------------------------------------- 210.3cm.
More informationInstruction Manual book
book ITEM CODE:BH 145 SPECIFICATION Wingspan: 6,000mm 236.22 in. Length : 2,800 mm 110.24 in. Weight : 18.5 kg 40.7 Lbs. Parts listing required (not included). Radio : 07-08 channels. Servo : 09-10 standard
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 2190mm (86.2 in) - Length: 1907mm (75 in) - Flying weight: 9000-12000 gr - Wing area: 92 dm2 - Wing loading: 98g/dm2 - Wing type: Naca airfoils - Retract gear type: Air-retract
More informationStrix Goblin Instruction Manual. Rev
Strix Goblin Instruction Manual Rev 3-4.24.2017 1 Introduction Thank you for purchasing the Strix Goblin! This is a high performance plank style aircraft and it was designed using aerodynamic principles
More informationHIGH WING MK2 GP/EP ARF SCALE
SONIC HIGH WING MK2 GP/EP.25-.32 ARF SCALE 1:10 SPECIFICATION - Wingspan: 1340mm (52.7in) - Length: 1040mm (40.9 in) - Flying weight: 1800-2000 gr - Wing area: 27 dm2 - Wing loading: 79g/dm2 - Wing type:
More informationAviator Pro 120 ARF. Instruction Manual. Specifications
Aviator Pro 120 ARF Instruction Manual Specifications Wingspan: 110 in (2800 mm) Length: 74 in (1870 mm) Wing Area: 1581sq in (102 sq dm) Weight: 11.4-13.4 lbs (5190-6100 g) Dear Customer, Congratulations
More informationInstruction Manual book
Instruction Manual book Item code:bh144 SPECIFICATION Wingspan : 1,400 mm 55.12 in. Length : 1,350 mm 53.15 in. Weight : 4 kg 8.8 Lbs. Empty Weight: 1.9 kg 4.18 lbs Radio : 08 channels. Servo : 08 size
More informationInstruction Manual. Specification:
Instruction Manual L O W Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1790gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo W I N G KIT CONTENTS: We have
More informationInstruction Manual book
Instruction Manual book ITEM CODE:BH135 SPECIFICATION Wingspan : 4,200mm. 163.35 in. Length : 2,100 mm. 82.68 in. Weight : 7,6 kg. 16.72lbs Radio : 07 channels. Servo : 05 06 standard high torque servos,
More informationPlantraco Micro Racer Shoestring Racer Preliminary Manual Version 1.1
Plantraco Micro Racer Shoestring Racer Preliminary Manual Version 1.1 Thank you for purchasing the Plantraco Micro Racer Shoestring. Many hours have gone into developing this model. We hope you enjoy building
More informationASSEMBLY MANUAL. Kit features. MS:88
MS:88 ASSEMBLY MANUAL Graphics and specfications may change without notice. Specifications: Wingspan-------------------------------------------------- 70.9 in--------------------------------------- 180cm.
More informationInstruction Manual book
book (pusher propeller) ITEM CODE:BH 142 SPECIFICATION Wingspan : 1,450mm 57.09 in. Length : 1,165 mm 45.87 in. Weight : 3.3kg 7.26 Lbs. Radio : 05 channels. Servo : 07 size (29 x 13 x 30) mm. Electric
More informationInstruction Manual book
book SPECIFICATION Wingspan : 1,450 mm 57.09 in. Length : 1,200mm 47.24in. Weight : 3.1 kg 6.82 Lbs. Radio : 05 channels. Servo : 07 servos. Engine : 61-75 2 stroke. 91 4 stroke. Made in Vietnam. This
More informationRADIO CONTROL MODEL HURRICANE
RADIO CONTROL MODEL VQAA040G VQAA040B HURRINE Almost ready to fly SPECIFITIONS Wingspan...63 in. / 161cm Length...50 in. / 129cm Engine...50~60 2T / 70~90 4T Or Electric equivalent. RC Functions: Motor
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1420mm (55.91 in) - Length: 1370mm (53.94 in) - Flying weight: 2600-2800 gr - Wing area: 41.6 dm2 - Wing loading: 65g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationInstruction Manual book
book SPECIFICATION Wingspan : 1.750mm 68.90 in. Length : 1.280 mm 50.39 in. Weight : 3.2-3.5 kg 7.04-7.7 Lbs. Radio : 06 channels. Servo : 07-09 mini servos +3 servos retracts (FUTABA,S3170G) Parts listing
More informationInstruction Manual book
book ITEM CODE: BH99. SPECIFICATION Wingspan : 2,850 mm 112.20 in. Length : 1,910 mm 75.20 in. Weight : 8.1 kg 17.82 Lbs. Radio : 06 channels. Servo : 08 servos. Engine : 35 CC gas. Made in Vietnam. This
More informationINSTRUCTION MANUAL BOOK
INSTRUCTION MANUAL BOOK ITEM CODE BH57. SPECIFICATION Wingspan: 1,470 mm. 57.87 in. Length : 1,180 mm. 46.46 in. Weight : 2.7 Kg. 5.94 Lbs. Engine : 46 cu.in 2 stroke. 52 cu.in 4 stroke. Radio : 4 channels.
More informationYAK54 MK2. GP/EP size.120/20cc SCALE 1:4 ¾ ARF. Instruction Manual. version. version
Instruction Manual GP EP version version GP/EP size.10/0cc SCALE 1:4 ¾ ARF SPECIFICATION - Wingspan: 168 (66.3 in) - Length: 1605mm (63.1 in) - Flying weight: 4700-500 gr - Wing area: 54.7 dm - Wing loading:
More informationHERO 3D SCALE 1:6 ARF
Instruction Manual SPECIFICATION - Wingspan: 1500mm(59 in) - Length: 1410mm (55.5 in) - Flying weight: 2100-2300 gr - Wing area: 58 dm2 - Wing loading: 39g/dm2 - Covering type: Genuine ORACOVER - Gear
More informationDassault Aviation FALCON 7 X. for Jet CAT P160. Assembly Manual. AVIATION Design
Dassault Aviation FALCON 7 X for Jet CAT P160 Assembly Manual AVIATION Design ZI le chenet, 91490 Milly La Foret, FRANCE Tel : 33 1 64 98 93 93 Fax : 33 1 64 98 93 88 E-mail : aviation.design@wanadoo.fr
More informationAVIATOR 25 ARF Almost Ready-to-Fly
AVIATOR 25 ARF Almost Ready-to-Fly Instruction Manual Specifications Wingspan: 54.3 in (1380mm) Length: 45.2 in (1150mm) Wing Area: 438 sq in (34sq dm) Flying Weight: 3.8 b (1700g) Dear Customer, Congratulations
More informationRECOMMENDED MOTOR AND BATTERY SET UP
SPECIFICATION - Wingspan: 1669mm (65.7in) - Length: 1229mm (48.43 in) - Flying weight: 3300-3400 gr - Wing area: 44.2 dm2 - Wing loading: 67g/dm2 - Wing type: Naca airfoils - Covering type: Genuine ORACOVER
More informationSTEP 1 - APPLYING HINGE BEVELS TO FRONT WING, REAR WING, VERTICAL STABILIZER, AND RUDDER FRONT WING (UNDERSIDE) 45 DOUBLE HINGE BEVEL
SkyRaiderv.b WING SPAN: FRONT - 22 in. REAR - 28.5 in. LENGTH: 35.25" WING AREA: 381 sqin. WEIGHT: 19-20oz. (RECOMMENDED) POWER: HACKER A20-20L, 10x3.8 APC PROP, 3S1P 1320mah Lipo 15C, 20A ESC RADIO: 4
More informationTable of Contents. Tail Wheel Assembly Installation.. page 01. Stabilizer Installation.. page 02. Fin Installation.. page 03
Table of Contents Tail Wheel Assembly Installation.. page 01 Stabilizer Installation.. page 02 Fin Installation.. page 03 Elevator and Rudder Hinge Installation.. page 04 Rudder Controls.. page 05 Elevator
More information2) Bilateral air intakes allows for reliable ventilation,keep the edf perfect blend in the side of body.
INSTRUCTIONS FOR ZEPHYR V-70 EDF-EPO Warning: This aircraft is a hobby grade product, only for people of 14 years of age or above. Please read and understand all instructions before opeating. Features:
More informationELVIRA. Elvira building instruction October
Wing span [mm]: 4500 Aspect ratio: 20 Wing area [dm2]: 101,18 Wing loading: 52-83 Weight [g]: 5300-8400 Airfoil: VS1 0BBUILDING INSTRUCTION ELVIRA www.pcm.at 1 CONTENTS DATA 1. Kit Contents 2. What else
More informationInstruction Manual BULLDOG. Wingspan : 1410 mm (55.5in) : 1450 mm (57.1in) : 4900gr gr. Weight. : 6-9 Channel/ 7 servo high torque, 1standard
Wingspan : 1410 mm (55.5in) Length Weight Radio Engine : 1450 mm (57.1in) : 4900gr - 5600gr : 6-9 Channel/ 7 servo high torque, 1standard : 1.20/ 2 stroke 1.80/ 4 stroke KIT CONTENTS: We have organized
More informationInstruction Manual book
book SPECIFICATION Wingspan : 2,080 mm 81.89 in. Length : 1,680 mm 66.14 in. Weight : 6.2 kg 13.64 Lbs. Radio : 06 channels. Servo : 06 servos. Engine : 30-35 CC Gas(FUJI IMVAC). Made in Vietnam. This
More informationInstruction Manual book
book SPECIFICATION Wingspan : 2,310 mm 90.94 in. Length : 1,750 mm 68.90 in. Weight : 8.4 kg 18.48 Lbs. Radio : 06 channels. Servo : 09 servos + 2 mini servos (elevator). Engine : 45-55CC gas. Made in
More information(Glider) ASSEMBLY MANUAL
(Glider) MS:132 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications: Wing span ------------------------------118.1in (300cm). Wing area ---------------------902.1sq.in
More informationRVJET Flying wing specially designed for FPV. RangeVideo Wireless Video Solutions
RVJET Flying wing specially designed for FPV Features: Durable EPO in black or white Variable wing span 1.55m/1.95m Compact during transport (original packing can be used) Specially designed for RVOSD
More informationInstruction Manual book
Instruction Manual book SPECIFICATION Wingspan : 1,800mm. 70.87 in. Length : 1,350 mm. 53.15in. Weight : 3.6kg. 7.92lbs. Parts Listing required (not included). Glow Engine : 55-61 2 stroke. 91 4 stroke.
More informationInstruction Manual book
book ITEM CODE:BH 139 SPECIFICATION Wingspan : 1,450mm 57.09 in. Length : 1,140 mm 44.88 in. Weight : 3.3kg 7.26 Lbs. Radio : 05 channels. Servo : 07 mini servos+ 3servos Retracts (FUTABA S3170G) EDF:
More informationASSEMBLY MANUAL. Graphics and specifications may change without notice.
NEMESISMS: SEA 111 ASSEMBLY MANUAL Graphics and specifications may change without notice. Specifications Wing span------------------------------------- 55.9in ------------------------------- 142cm. Wing
More informationASSEMBLY MANUAL. Specifications
ASSEMBLY MANUAL MS: SEA 82 Graphics and specfications may change without notice. Specifications Wingspan-------------------------------------- 70.9 in------------------------------ 180cm. Wing area-------------------------------------
More informationMS:176 ASSEMBLY MANUAL. Graphics and specifications may change without notice.
ASSEMBLY MANUAL MS:176 Graphics and specifications may change without notice. Specifications: Wing span ------------------------------98.4in (250cm). Wing area ----------------1576.4sq.in (101.7sq dm).
More informationF9F-2 OPERATIONAL MANUAL
F9F-2 OPERATIONAL MANUAL 7 different color to meet customer s choice. 2 different material F9F-2/OB: F9F-2/TB: F9F-2/YB: F9F-2/WR: F9F-2/GYR: F9F-2/GRW: F9F-2/BRY: Original Blue Tail Blue Yellow/Blue White/Red
More informationInstruction Manual book
book SPECIFICATION Wingspan : 1,920 mm 75.59 in. Length : 1,560 mm 61.42 in. Weight : 5 kg 11.00Lbs. Radio : 06 channels. Servo : 09 servos. Engine : 120 4 stroke. Made in Vietnam. This instruction manual
More informationInstruction Manual book
book Item code:bh131 SPECIFICATION Wingspan : 3,000 mm 118.1 in. Length : 1,600 mm 62.99 in. Weight : 2.2 kg 4.84 Lbs. Radio : 05 channels. Servo : 06 mini servos. Electric Motor: BOOST 40 Battery : 3celIs
More informationSBD DAUNTLESS GP/EP SIZE ARF SCALE 1:8. Instruction Manual
GP/EP SIZE.46-.55 ARF SCALE 1:8 SPECIFICATION - Wingspan: 1440mm (56.7in) - Length: 1140mm (44.9 in) - Flying weight: 3000-3300 g - Wing area: 42 dm2 - Wing loading: 78g/dm2 - Wing type: Naca airfoils
More informationPANTERA Electric Prop Jet ARF
PANTERA Electric Prop Jet ARF Copyright 2017 Extreme Flight 1 Greetings and congratulations on your purchase of the SPEED FREAK PANTERA! The PANTERA is the second release from SPEED FREAK and is built
More informationInstruction Manual book
Instruction Manual book SPECIFICATION Wingspan : 1,920 mm 75.59 in. Length : 1,560 mm 61.42 in. Weight : 5 kg 11.00Lbs. Radio : 06 channels. Servo : 09 servos. Engine : 120 4 stroke. Made in Vietnam. JU87-STUKA
More informationNeptune Seaplane25 ARF. Instruction Manual. Specifications
Neptune Seaplane25 ARF Instruction Manual Specifications Wingspan: 1270mm (50in) Length: 1155mm (45.5in) Wing Area: 34.8 sq dm (539.4 sq in) Weight: 1950g (4.30lbs) Product Highlights Removable hatch on
More informationAssembly Manual. Version 01/01/2006
Assembly Manual ZI le chenet, 91490 Milly La Foret, FRANCE Tel : 33 1 64 98 93 93 Fax : 33 1 64 98 93 88 E-mail : aviation.design@wanadoo.fr www.adjets.com Version 01/01/2006 INTRODUCTION is our new jet
More information... BY: Scott Barnhart
Wi! ;ql ;~,... TEe ONEYAII54...................................................................................... BY: Scott Barnhart I TALK UP TmSYAK Techone Hobby is a company schemes. The computer numeric
More informationInstruction Manual book
Instruction Manual book SPECIFICATION Wingspan : 1,920 mm 75.59 in. Length : 1,560 mm 61.42 in. Weight : 5 kg 11.00Lbs. Radio : 06 channels. Servo : 09 servos. Engine : 120 4 stroke. Made in Vietnam. JU87-STUKA
More informationDeHavilland DH88 Comet
DeHavilland DH88 Comet INSTRUCTION MANUAL A semi scale ARF R/C model of the famous winner of the 1934 MacRobertson, England to Australia Air Race. Technical Specification Wingspan: 88 inches (2235 mm)
More informationUltimate EP. Before commencing assembly, please read these instructions thoroughly. I NSTRUCTI ON M ANUAL. Warning! This model is not a toy.
I NSTRUCTI ON M ANUAL Before commencing assembly, please read these instructions thoroughly. Ultimate EP (GM05) Specifications Wing Span: 3.5 in / 85 mm Wing Area: 357 sq in / 3 sq dm Flying Weight: 4
More information