BellMega BM-510. Operation Manual Ver: 1.0 Rev: 1
|
|
- Rosemary Griffith
- 5 years ago
- Views:
Transcription
1 BellMega BM-510 Operation Manual Ver: 1.0 Rev: 1
2 CONTENTS Page Description 1 Operation 2 Safety 2 Charging 3 Service / Calibration 3 Specifications 4
3 Description The BellMega is a continuity tester for point to point wiring verification and includes Earth Leakage Detection of the wiring being tested. The leakage resistance is detected within 110M Ohms. The high voltage DC source is regulated to provide a stable reference for insulation breakdown resistance detection. The earth leakage threshold is detected using the voltage divider principal. A regulated high voltage is applied to two known HV metal film resistors and a variable resistor is used to calibrate the threshold of detection as a function of time and leakage resistance. i.e.: 110M Ohms will trip the alarm in approx 200Ms, 10M Ohms will trip the alarm in approx 20Ms. The important point is that this is shorter than the response of the bell tone. As any leakage resistance <110M Ohms will trip the unit, the high voltage drop M Ohms is of no relevance because the detection of the leakage resistance is a function of the regulated high-voltage supply (1%) and calibrated internal resistance. The BellMega includes battery state monitoring via a green / red led on the front panel. When the led turns red (<10.4v) continuously it is time to charge the battery. A low voltage (<9.8v) disables the continuity test tone, ensuring the high voltage DC is still valid and the circuit is functioning predictably during a period of low battery supply. For maximum battery life, the unit should only be recharged when the led turns red. The BellMega has front panel test points to verify that the unit is operating within specifications before testing any wiring. Use the black lead -> test points for checking operation. (See fig 1) The high voltage can be tested using a 10M Ohms Digital multimeter only, (i.e. Fluke 87), measure the voltage between the black and green terminals, the result should be 520v + 10v/-5v. The 10mA constant current source can be tested by connecting an ammeter to the black and red terminals. A hi/low sound level is provided to accommodate different testing environments. There are three fuses internally, AC/DC in, Probes and DC-DC Converter, for protection against excess current faults. These fuses are not user replaceable. Copyright 2005, MRD Rail Technologies Pty Ltd, All Rights Reserved Page 1
4 Operation 1 When the unit is first switched on, the insulation alarm may sound. Press reset to clear. The Battery LED should be green and the neon indicator near the Earth terminal should be on. Note: The battery status LED is only valid during use and is not a fully charged indicator for charging. 2 Check the BellMega unit at the start of the bell testing by using the front panel test points. The bell tone should sound only for the 8R test. The Insulation alarm tone will latch on only for the 80M and 100M test. Press the reset to cancel the alarm tone. If any of these tests fail, do not use as the unit may require service or calibration. 3 If the unit is in calibration and passes all tests, connect the earth lead of the BellMega to the earth bus of the equipment to be tested. Ensure all equipment earths are terminated. The red and black leads are for the continuity (bell) testing. Any earth leakage <110M Ohms will trip the earth alarm (low tone) and disable the bell tone. Press the reset to cancel the alarm and investigate the source of the earth leakage. When the battery LED turns red it is time to charge the battery, continuity function will disable if the unit is used to further discharge the battery. 4 If the wiring being tested is live, the continuity tone will be disabled and the live circuit LED on the front panel will light, if the voltage is greater than 23v. 5 During extreme humidity environment and low air circulation, the earth leakage alarm will trip. This is mostly caused by old test leads and surface resistivity on equipment terminals. This can be remedied by replacing test leads with new 1kv PVC 24/.020 wire. Silicone test leads can be used, but are usually not suitable due to the reduced mechanical strength. Improving air circulation by using a fan will also reduce false tripping due to surface condensation. The unit can also be re-calibrated and labeled accordingly to suit requirements. Safety The BellMega is a HIGH VOLTAGE power supply and should be treated with care and respect. Do not touch the probe tips and earth / case at the same time. The +high voltage (530v) has approximately 200k Ohms series resistance between EARTH terminal / case and probes. The EARTH terminal is connected to the BellMega CASE. Only Authorised and Qualified personnel to open the case. Disconnect all electronic equipment from wiring before bell testing. Ensure no flammable gases or other flammable substances are present when bell testing. Do not use the BellMega if it gets wet. Copyright 2005, MRD Rail Technologies Pty Ltd, All Rights Reserved Page 2
5 Charging Important: Recharge battery as soon as possible after use and especially before the unit is to be stored or unused. The BellMega uses a 1.3ah sealed Lead Acid battery, it is not necessary to wait for complete discharge before recharging. The charger in the BellMega is a constant voltage / current limited type and requires a suitable plug pack power supply. The charging can be left on indefinitely as the battery will be floated at 13.6v. For best results the unit should be charged for 4-5 hours. Always fully charge the battery if unused. The unit can be operated while being charged, only if the supply is isolated from the mains earth and fully insulated power leads are used. After long term storage (6-12 months), the battery capacity is initially reduced, normal capacity will return with 2-3 charge / discharge cycles. Service / Calibration Important: The case may be opened only by authorised service personnel. Calibration can only be guaranteed if the unit remains sealed from the previous calibration and is re-calibrated within due date specified. Danger: The 530v present within the case has lethal current capability due to its low impedance and regulated characteristic. Warning: The case is connected to the +530v DC via a 100k resistor, this is EARTH. Remove jumper from J1 before connecting test equipment. This will disconnect the earth connection from the case. This is because testing and calibration are done with reference to battery 0v. Calibration must be performed by authorised personnel or approved calibration lab only, using calibrated, traceable test equipment to ISO/IEC Copyright 2005, MRD Rail Technologies Pty Ltd, All Rights Reserved Page 3
6 Operating Specifications Specification: REV C Insulation leakage trip Insulation leakage trip response time Insulation voltage High voltage supply Insulation short circuit current High voltage drop at terminals Continuity threshold Continuity constant current Continuity applied voltage Continuity response time Live circuit tolerance Live circuit LED operates at.. Operating supply range (battery) Low battery warning LED at.. Low battery disable Operating current (battery) Operation time (fully charged battery) Operation time (using plug pack) Plug pack type Battery Charge time Insulation sound frequency lo Continuity sound frequency hi Switch mode cycle frequency 110M ohm M / 100pf 520v dc 10M (note 1) 530v dc regulated 1% 1.5mA max 5M ohm. (note 1) 0.909M ohm. (note 1) 10 ohm 10mA +/- 1mA 11v dc+/- 2v (red = +) 400ms +/- 100ms 250v ac/dc (350v peak) 25v ac/dc v 10.4v +/- 0.2v 9.4v 10.4v 125mA 7 hours (approx.) Indefinitely 15 18v 600mA(min) EARTH ISOLATED!!!!!!! LCR12V1.3P 12V 1.3AH/20hr 3.9 hours min. 1.7khz +/- 100hz 2.2khz +/- 100hz 40 70khz (factory set) Copyright 2005, MRD Rail Technologies Pty Ltd, All Rights Reserved Page 4
Dycon D1532SM. EN50131/PD6662 Grade 3, 12V 2A Power Supply. Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD
Dycon D1532SM EN50131/PD6662 Grade 3, 12V 2A Power Supply Technical Description Installation and Operating Manual DYCON POWER SOLUTIONS LTD Tel: +44 (0)1443 471 900 Unit A Cwm Cynon Business Park Mountain
More informationMARTINDALE INSTRUCTIONS ELITE FUSE FINDER KIT ELECTRIC. Trusted by professionals. 4.4 Storage Conditions
4.4 Storage Conditions The FD650/R and FD500/T or FD600/T should be kept in warm dry conditions away from direct sources of heat or sunlight, with the battery removed and in such a manner as to preserve
More informationDycon D2430 EN54-4 Fire Alarm Power Supply Series
Dycon D2430 EN54-4 Fire Alarm Power Supply Series Technical Description Installation and Operating Manual Construction Product Regulation 0359-CPR-00434 Page 1 of 14 Contents 1. General... 3 1.1 Product
More information99 Washington Street Melrose, MA Fax TestEquipmentDepot.com. Instruction Manual. Model 2831D 4 ½ Digit True RMS Digital Multimeter
99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com Instruction Manual Model 2831D 4 ½ Digit True RMS Digital Multimeter 1 1. PRODUCT DESCRIPTION 1-1. Introduction Thank you
More information362 Clamp Meter. Users Manual
362 Clamp Meter Users Manual PN 3622678 August 2010, Rev. 1, 4/13 2010, 2013 Fluke Corporation. All rights reserved. Printed in China. Specifications are subject to change without notice. All product names
More informationPowerOhm Installation Manual for BM R Series Braking Modules
PowerOhm Installation Manual for BM R Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal
More informationTOWER MAXI T SINGLE CONVERSION ON LINE UPS SYSTEMS
INSTRUCTION MANUAL TOWER MAXI T SINGLE CONVERSION ON LINE UPS SYSTEMS September 2000 TOWER UPS DISTRIBUTION (PTY) LTD 1 1. INTRODUCTION T A B L E O F C O N T E N T S 1.1 General Description... 3 1.2 Features...
More information27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2
1 27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2 STX2401-C STX2401-T FEATURES 0843-CPR-0213 14 Elmdene International Ltd Tel: +44(0)23 9269 6638 3 Keel Close, Interchange Park, Fax:
More informationCONTENTS TABLE OF CONTENTS... 1 INTRODUCTION... 2 SEC 1 - SPECIFICATIONS... 3 SEC 2 - DESCRIPTION... 5 SEC 3 - OPERATING INSTRUCTIONS...
CONTENTS SUBJECT PAGE TABLE OF CONTENTS... 1 INTRODUCTION... 2 SEC 1 - SPECIFICATIONS... 3 SEC 2 - DESCRIPTION... 5 SEC 3 - OPERATING INSTRUCTIONS... 8 SEC 4 - BATTERY CHARGING NOTES... 9 SEC 5 - VERIFICATION
More informationCONTENTS 1. INTRODUCTION SAFTY INSTRUCTION CABLE CONNECTION SYSTEM DESCRIPTION INVERTER OPERATION...
CONTENTS 1. INTRODUCTION...... 1 2. SAFTY INSTRUCTION.......... 2 3. CABLE CONNECTION.......... 4 4. SYSTEM DESCRIPTION............ 5 5. INVERTER OPERATION... 11 6. TROUBLE SHOOTING GUIDE....... 16 7.
More informationMY /2-DIGIT DIGITAL MULTIMETER Users Manual
MY-65 4 1/2-DIGIT DIGITAL MULTIMETER Users Manual Read the Users Manual thoroughly before use. WARRANTY This instrument is warranted to be free from defects in material and workmanship for a period of
More informationPREMIER POWER PACK INSTRUCTION MANUAL EN54-4 POWER SUPPLY UNIT INSTRUCTION MANUAL. GLT.MAN-138 Issue: /05/2016 N.R.P.J.
EN54-4 POWER SUPPLY UNIT INSTRUCTION MANUAL GLT.MAN-138 CONTENTS Introduction to the Premier Power Pack PSU... 2 Changes to EN54-4 (The Fire Alarm Equipment Power Supply Standard)... 3 Indications... 4
More informationDielectric Withstand Tester
Dielectric Withstand Tester Model HT-20KVPac 0-20,000 Volts AC Output Instruction Manual i Dear Customer: Congratulations! Compliance West USA is proud to present you with your Dielectric Withstand Tester.
More informationHT Dielectric Withstand Tester Volts AC Output 25mA Leakage Option
HT-10000 Dielectric Withstand Tester 0-10000 Volts AC Output 25mA Leakage Option Instruction Manual COMPLIANCE WESTUSA Dear Customer: Congratulations! Compliance West USA is proud to present you with your
More information80 Series V Digital Multimeter Safety Information
80 Series V Digital Multimeter Safety Information Limited Lifetime Warranty. See the Users Manual for the full warranty. Go to www.fluke.com to register your product and find more information. A Warning
More informationINSTALLATION MANUAL AND OPERATING INSTRUCTIONS. TT43 Battery Tester/Charger. True Blue Power is a division of Mid-Continent Instrument Co., Inc.
INSTALLATION MANUAL AND OPERATING INSTRUCTIONS TT43 Battery Tester/Charger True Blue Power is a division of Mid-Continent Instrument Co., Inc. Mid-Continent Instrument Co., Inc. dba Mid-Continent Instruments
More informationSECTION DC POWER SUPPLY/BATTERY CHARGER
SECTION 26 33 05 PART 1 - GENERAL 1.1 THE REQUIREMENT A. The CONTRACTOR shall provide the single-phase heavy-duty industrial battery charger and all accessories required, complete and operable, in accordance
More informationUSER MANUAL. Power GUARD UPS. Uninterruptible Power System
USER MANUAL Power GUARD UPS Uninterruptible Power System IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions for Power GUARD that should be followed during
More informationPowerterm L120C Single Output PSU/Battery Chargers Model C2199A-1 (12V/8A) or Model C2199A-2 (24V/6A)
A Complete solution for small battery-backed dc instrument power systems. DATASHEET Supply 12Vdc 8A or 24Vdc 6A loads Ideal for RTU s, dataloggers, remote field instrumentation, alarm systems, etc. where
More informationSDS Enclosed Star-Delta Starter User Guide
SDS Enclosed Star-Delta Starter User Guide (7.5kW~90kW) V2.0.0 PLEASE NOTE: AS STANDARD AND UNLESS OTHERWISE SPECIFIED, THIS PRODUCT IS EQUIPPED WITH A BASIC LOW INTEGRITY EMERGENCY STOP CIRCUIT STOPPING
More informationOPERATING INSTRUCTIONS
Manual No LI-4159-MIL OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS NAVY BATTERY CHARGER / ANALYZER P/N 4159-MIL MODEL CA-1550-MIL NSN: 4920-01-498-2543 Issued By: LamarTechnologies LLC 14900 40th Ave.
More informationMetrohm E3640 FLASH TESTER INSTRUCTION MANUAL. Martindale Electric Co Ltd.
Metrohm Martindale Electric Metrohm House, Imperial Park, Imperial Way, Watford, Hertfordshire, WD24 4PP, UK T: 01923 441717 F: 01923 446900 Email: sales@martindale-electric.co.uk web: www.martindale-electric.co.uk
More informationK25000 & KD25000 Series
K25000 & KD25000 Series Fire Alarm Power Supplies Installation, Commissioning and Operating Manual Man-1128 Issue 14 January 2016 Man-1128_K25400_series_Power_Supply_Manual_14 Page 1 of 20 Section Page
More informationGEPA. ARG-24 Series Battery Charger & Battery Group. User Guide
GEPA ARG-24 Series Battery Charger & Battery Group User Guide Contents 1. General... 1 2. Features... 2 3. Montage & Wiring... 3 3.1. Montage... 3 3.2. Wiring... 4 4. Usage... 5 4.1. Interface... 5 4.1.1.
More informationl The Battery Tester is designed for measuring the l AC four-terminal method to measure the internal
Certificate of Calibration We hereby certify that this product has been calibrated and found to be in accordance with the applicable SPECIFICATIONS and STANDARDS. Accuracies of the standard equipment used
More informationMODVAR Low voltage reactive power compensation modules Installation manual
MODVAR Low voltage reactive power compensation modules Installation manual MODVAR Low voltage reactive power compensation modules Before installation, read this manual carefully and keep at the disposal
More informationHE-PSU(4.0) Power Supply & Battery Charger Installation, Commissioning & Operating Manual
HE-PSU(4.0) Power Supply & Battery Charger Installation, Commissioning & Operating Manual Page 1 of 10 CONTENTS 1. GENERAL...2 2. POWER REQUIREMENTS...2 2.1 HE-PSU(4.0) Input/Output Electrical Ratings...2
More informationINSTRUCTION MANUAL MARTINDALE CM52 CLAMP METER. ELECTRIC Trusted by professionals. Other products from Martindale:
Other products from Martindale: 18th Edition Testers All-in-one s Calibration Equipment Continuity Testers Electrician s Kits Full Calibration & Repair Service Fuse Finders Digital Clamp Meters Digital
More informationOperator s Handbook For Compact High Voltage DC15 & DC30 POROSITY (HOLIDAY) DETECTORS
Operator s Handbook For Compact High Voltage DC15 & DC30 POROSITY (HOLIDAY) DETECTORS Can be used in accordance with: Australian Standard AS3894.1 ASTM G62, ASTM D5162, ASTM D4787, NACE SP0274, NACE SP0490,
More informationInstallation Instructions
AQU244 & AQU128 Series Installation Instructions Installation Instructions AQU244 24vdc 5A Supervised Power Supply/Charger module AQU128 12vdc 10A Supervised Power Supply/Charger module Both Mounted in
More informationHitachi America, Ltd.
Hitachi America, Ltd. RCU Series Regenerative Converter Unit Instruction Manual NOTE: REFER ALSO TO APPLICABLE INVERTER INSTRUCTION MANUAL Manual Number: HAL1057A May 2010 After reading this manual, keep
More informationHT Dielectric Withstand Tester Volts AC Output Volts DC Output COMPLIANCE WESTUSA. Instruction Manual
HT-5000 Dielectric Withstand Tester 0-5000 Volts AC Output 0-7200 Volts DC Output Instruction Manual COMPLIANCE WESTUSA Dear Customer: Congratulations! Compliance West USA is proud to present you with
More informationInstallation and Operating Instructions. Solar System Controller ISC3020
Installation and Operating Instructions Solar System Controller ISC3020 ABOUT THIS MANUAL These operating instructions come with the product and should be kept with it as a reference to all user s of
More informationDigital Insulation Resistance Testers. you can depend on
Digital Insulation Resistance Testers you can depend on Fluke 1550 MegOhmMeter Digital insulation testing up to 5000 Volts The Fluke 1550 is a digital insulation tester capable of testing switchgear, motors,
More informationPower Inverter. User s Manual. Diamond Series CPD1200EILCD
Power Inverter Diamond Series CPD1200EILCD User s Manual 2 TABLE OF CONTENTS 1 IMPORTANT SAFETY INSTRUCTIONS..4 2 INSTALLATION....5 2-1 Unpacking...5 2-2 Product Overview & Outlook..5 2-3 Power Requirements
More information24V 3A EN54 Ancillary Power Supply
24V 3A EN54 Ancillary Power Supply Normal supply - green light on Fault condition - call Engineer Control relay - activated 3A Power Supply C-TEC Manufactured in England by C-Tec EN 54-4 : 1997 INSTALLATION
More information1. INTRODUCTION AND SYSTEM DESCRIPTION SPECIFICATIONS... 5
TABLE OF CONTENTS 1. INTRODUCTION AND SYSTEM DESCRIPTION... 4 2. SPECIFICATIONS... 5 2.1 CURRENT CAPACITY:... 5 2.2 VOLTAGE MEASUREMENT CAPACITY:... 5 2.3 VOLTAGE SOURCE:... 5 2.4 SHUNT:... 5 2.5 METERS:...
More informationInstallation and Operating Instructions. Solar System Controller ISC3030
Installation and Operating Instructions Solar System Controller ISC3030 ABOUT THIS MANUAL These operating instructions come with the product and should be kept with it as a reference to all user s of the
More informationLow Frequency Inverter. User Manual
Pure Sine Wave 220-240V 50-60Hz Low Frequency Inverter User Manual For LK/LW series Power Star inverters only, models: LK2000, LK2000-24, LK3000, LK3000-24, LK3000-48, LK6000-24, LK6000-48 1. Safety precautions
More informationValcom Failsafe Unit. 1620ESv2 SERIES. Operation and Maintenance Manual
Valcom Failsafe Unit 1620ESv2 SERIES Operation and Maintenance Manual Table of Contents Section Title Page 1. - Introduction.. 2. - Unpacking the Failsafe unit. 3. - Installation 3.1 - Auto / Timed UPS
More informationOpen Chassis Star-Delta Starter User Guide
Open Chassis Star-Delta Starter User Guide (7.5kW~90kW) V2.0.1 Contents 1 Safety information... 1 2 Technical Data... 2 3 Supply & Motor Connections & Circuit Diagrams... 5 4 Control Connections & Operation...
More informationGo to to register your product and find more information.
ESA609 Electrical Safety Analyzer Safety Sheet Go to www.flukebiomedical.com to register your product and find more information. Safety Information A Warning identifies hazardous conditions and actions
More informationUser Manual Rittal PMC UPS 6kVA
User Manual Rittal PMC UPS 6kVA Germany Rittal GmbH & Co. KG Auf dem Stützelberg D-35745 Herborn Tel.: ++49-27 72-5 05-0 Fax: ++49-27 72-5 05-23 19 Internet: www.rittal.de 26 Contents 1. Introduction...
More informationFreedom egen System End-of- Line Functional Checklist
U Freedom egen System End-of- Line Functional Checklist 976-0361-01-01 Rev A April 2018 DANGER RISK OF FIRE, ELECTRIC SHOCK, EXPLOSION, AND ARC FLASH This checklist is in addition to, and incorporates
More informationS4562C 1085 COMBI BOARD APPLICATION. Contents PRODUCT HANDBOOK. General
S4562C 1085 COMBI BOARD APPLICATION PRODUCT HANDBOOK The S4562C 1085 combi board is an integration of an on/off temperature control and an electronic ignition control. The S4562C 1085 combi board is intended
More informationDocument: PRODSPEC-140 Revision: G DCN No Date: October 1, 2014 Product: 10-amp EnerGenius NRG Battery Charger
Document: PRODSPEC-140 Revision: G DCN No. 106512 Date: October 1, 2014 Product: 10-amp EnerGenius NRG Battery Charger 1. GENERAL DESCRIPTION 1.1 General Description Fully regulated, constant voltage,
More informationKV4-300 mk2. KV5-200 mk2. KV5-100T mk2. KV3-250 mk2
OPERATING AND MAINTENANCE MANUAL Product: Type: High Voltage AC Test Set KV3-250 mk2 KV4-300 mk2 KV5-100 mk2 KV5-100T mk2 KV5-200 mk2 DESIGNED AND MANUFACTURED BY: T & R Test Equipment Limited 15-16 Woodbridge
More informationCX-SERIES ADVANCED BATTERY CHARGER
CX-SERIES ADVANCED BATTERY CHARGER Table of Content 1. IMPORTANT SAFETY INFORMATION... 2 1-1 General Safety Precautions... 2 1-2 Battery Precautions... 2 2. FEATURES... 3 2-1 Battery Charging Curve...
More informationInstallation Manual for D154X Series Multi-Indicator, General Purpose Power Supplies
Installation Manual for D154X Series Multi-Indicator, General Purpose Power Supplies D1541 D1542 D1543 D1545 D1543-X-8 D1545-X-8 D1545-4BNC D154X Series 1A 2A 3A 5A 3A fitted with 8-way output splitter
More information1. INTRODUCTION AND SYSTEM DESCRIPTION CONDENSED OPERATING INSTRUCTIONS SPECIFICATIONS CONTROLS AND DISPLAYS...
TABLE OF CONTENTS 1. INTRODUCTION AND SYSTEM DESCRIPTION... 5 2. CONDENSED OPERATING INSTRUCTIONS... 8 2.1 Constant Current Charge (normal mode)... 8 2.2 Constant Voltage... 9 2.3 Peak Voltage Charge...
More information5. OVERCURRENT RELEASE (OCR)
5. OVERCURRENT RELEASE (OCR) Options available for the type AR ACBs include a highly reliable, multi-functional overcurrent release (OCR) with a built-in 8- bit microprocessor. This OCR is supplied with
More informationNON MAINTAINED TWIN SPOTLIGHT WALL MOUNT LED EMERGENCY LIGHT
Model No. PEL00581 NON MAINTAINED TWIN SPOTLIGHT WALL MOUNT LED EMERGENCY LIGHT 1 Please read these instructions carefully before starting installation and retain for future reference. The centre page
More informationR&S RT-ZC02 R&S RT-ZC03 AC/DC Current Probe User Manual
R&S RT-ZC02 R&S RT-ZC03 AC/DC Current Probe User Manual / User Manual Content 1 Introduction 3 2 Safety 3 3 Specifications RT-ZC03 6 Specifications RT-ZC02 7 4 Operating Instructions RT-ZC03 8 Operating
More informationManual. EN Appendix. Lynx Ion BMS 400A / 1000A
Manual EN Appendix Lynx Ion BMS 400A / 1000A 1. SAFETY INSTRUCTIONS 1.1 In general Please read the documentation supplied with this product first, so that you are familiar with the safety signs en directions
More informationKD1E Range Potential Indicators
KD1E Range Potential Indicators Operating Instructions 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Limited Warranty & Limitation
More informationOperating Manual (Edition 04/2004) sinamics. Braking Module / Braking Resistor SINAMICS G130
Operating Manual (Edition 04/2004) sinamics Braking Module / Braking Resistor SINAMICS G130 04/04 Contents Contents 1 Safety Information 1-1 2 General 2-1 3 Mechanical Installation 3-1 4 Connection 4-1
More informationPhoenix Inverter
Manual EN Handleiding NL Manuel FR Anleitung DE Manual ES Appendix Phoenix Inverter 12 250 12 375 12 500 12 800 24 250 24 375 24 500 24 800 48 250 48 375 48 500 48 800 1. Safety instructions WARNING: ELECTRIC
More informationTechnical Data Sheets
GE Consumer & Industrial Power Protection Technical Data Sheets Digital Energy Uninterruptible Power Supply SitePro 150 200 250 300 kva 400 VAC CE Series 6 Manufactured by: GE Digital Energy General Electric
More informationTime Electronics Ins-Cal. Insulation Tester Calibration System. Technical Manual
Time Electronics 5069 Ins-Cal Insulation Tester Calibration System Technical Manual V1.2 20/04/11 Time Electronics Ltd Botany Industrial Estate, Tonbridge, Kent, TN9 1RH Tel: +44(0)1732 355993 Fax: +44(0)1732
More informationEMERGENCY VEHICLE BATTERY MANAGER PS2024
EMERGENCY VEHICLE BATTERY MANAGER PS2024 2 The PS2024 (Fig. 1) is designed as a on-vehicle battery charger / battery charge state monitor. While the vehicle is at its base or station, the charger is connected
More informationInstruction Manual PC104/PC105 3-PHASE SOCKET TESTER. Check out what else you can get from Martindale:
Check out what else you can get from Martindale: 17th Edition Testers Accessories Calibration Equipment Continuity Testers Electricians Kits Environmental Products Full Calibration & Repair Service Fuse
More informationSafe, fast HV circuit breaker testing with DualGround technology
Safe, fast HV circuit breaker testing with DualGround technology Substation personnel safety From the earliest days of circuit breaker testing, safety of personnel has been the highest priority. The best
More informationMODEL 422 Submersible Pump Controller
MODEL 422 Submersible Pump Controller Monitors True Motor Power (volts x current x power factor) Detects Motor Overload or Underload Operates on 120 or 240VAC, Single-phase or 3-phase Built-in Trip and
More informationTechnical Data Sheets
GE Consumer & Industrial Power Protection Technical Data Sheets Digital Energy Uninterruptible Power Supply SitePro 400 & 500 kva 400 VAC CE Series 6 Manufactured by: GE Digital Energy General Electric
More informationThe 4HR-UPS 220V ac output is provided via a Pure Sine Wave inverter, allowing it to be backed up by 2x 12V standby batteries.
1 Elmdene International Ltd Tel: +44 (0)23 9269 6638 3 Keel Close, Interchange Park, Fax: +44 (0)23 9266 0483 Portsmouth, Hampshire, PO3 5QD, UK Web: www.elmdene.co.uk STANDBY 220V AC POWER SYSTEM IDEAL
More informationInstallation and Operating Instructions. MPPT Solar System Controller ISC3040
Installation and Operating Instructions MPPT Solar System Controller ISC3040 ABOUT THIS MANUAL These operating instructions come with the product and should be kept with it as a reference to all user s
More informationHillstone PowerBank HPB54 Series ( 400A 700A )
Technical data Sheet Hillstone PowerBank HPB54 Series ( 400A 700A ) Ref. HPB54-400-700 Page 1 of 6 Features Electronic variable control Manual constant current Full current control range Digital ammeter
More informationHI-POT/CONTINUITY TESTER Model PLEP01
HI-POT/CONTINUITY TESTER Model PLEP01 Instruction Manual MITCHELL INSTRUMENT CO. Dear Customer: Congratulations! Mitchell Instrument Co. is please to present you with your Hipot/Continuity Tester. This
More informationCDBR-B. Dynamic Braking Unit Instruction Manual. April 2009 Part Number: R1 Copyright 2009 Electromotive Systems
CDBR-B Dynamic Braking Unit Instruction Manual April 2009 Part Number: 146-10001-R1 Copyright 2009 Electromotive Systems 2009 MAGNETEK All rights reserved. This notice applies to all copyrighted materials
More informationIDEAL INDUSTRIES INC. TECHNICAL MANUAL - SUPPLEMENT MODEL
IDEAL INDUSTRIES INC. TECHNICAL MANUAL - SUPPLEMENT MODEL 61-791 The Service Information provides the following: This is a Supplemental Manual to Megger s DM220 Service Manual and is intended for Performance
More informationSpecification of Battery Charger
1 S O N E I L 6033 Shawson Dr., Unit 29, Mississauga, Ontario, Canada L5T 1H8 Ph.: (905) 565-0360 Fax: (905) 565-0352 http://www.soneil.com Revision No.: R01 Specification of Battery Charger MODEL: 6010SR
More informationCONTENTS 1. INTRODUCTION SAFTY INSTRUCTION CABLE CONNECTION SYSTEM DESCRIPTION OPERATION... 9
USER MANUAL 1 CONTENTS 1. INTRODUCTION... 1 2. SAFTY INSTRUCTION... 3 3. CABLE CONNECTION... 4 4. SYSTEM DESCRIPTION... 5 5. OPERATION... 9 6. TROUBLE SHOOTING GUIDE... 25 7. OPERATION MODES..... 27 8.
More informationIntegrated temperature test and calibration bench Model CBS-SC4000
Calibration technology Integrated temperature test and calibration bench Model CBS-SC4000 WIKA data sheet CT 92.33 Applications Testing and calibration of temperature measuring instruments such as: - Mercury
More informationSE-125 MANUAL GROUND-FAULT GROUND-CHECK MONITOR
SE-125 MANUAL GROUND-FAULT GROUND-CHECK MONITOR FEBRUARY 14, 2001 REVISION 3 Publication: SE-125-M Document: S95-C125-00000 Printed in Canada. Copyright 2001 by Startco Engineering Ltd. All rights reserved.
More informationCarbon Monoxide Transmitter
Introduction The CO Transmitter uses an electrochemical sensor to monitor the CO level and outputs a 4-20 ma signal. The standard product features a 2- wire loop-powered output. Optionally, the device
More informationElmdene International Ltd
1 Elmdene International Ltd Tel: +44(0)23 9269 6638 3 Keel Close, Interchange Park, Fax: +44(0)23 9266 0483 Portsmouth, Hampshire, PO3 5QD, UK Web: www.elmdene.co.uk 13.8Vdc Switch Mode Power Supply GEN3-08-y
More informationModel ½ Digit Multimeter
www.keithley.com Model 2110 5½ Digit Multimeter Calibration Manual 2110-905-01 Rev. C / August 2013 *P211090501C* 2110-905-01 A Greater Measure of Confidence A Tektronix Company Model 2110 5½ Digit Multimeter
More informationUninterruptible (ATX) Switching Power Supply. MODEL eups-350
POWER SUPPLY MODEL eups-350 SPECIFICATION PAGE: 1 OF 10 Uninterruptible (ATX) Switching Power Supply MODEL eups-350 POWER SUPPLY MODEL eups-350 SPECIFICATION PAGE: 2 OF 10 TABLE OF CONTENTS 1. INTRODUCTION:...
More informationCD3000S-1PH Thyristor Unit Heater Break version
USER S MANUAL Rev. 01/2007 CD3000S-1PH Thyristor Unit Heater Break version from 15A to 110A CD Automation S.r.l. Via Picasso 34/36-20025 Legnano (MI) ITALY Tel +39 0331 577479 Fax +39 0331 579479 E-Mail:
More informationMegaPulse. Antenna Surge PF 65
MegaPulse IMPULSE TESTER Antenna Surge PF 65 Instruction Manual Dear Customer: Congratulations! Compliance West USA is proud to present you with your MegaPulse Antenna Surge PF Impulse Tester. Your instrument
More informationREFERENCE MANUAL FORM: MX-TRM-E REL REV MTE
Matrix APAX 380V-415V 50Hz TECHNICAL REFERENCE MANUAL FORM: MX-TRM-E REL. September 2014 REV. 002 2014 MTE Corporation WARNING High Voltage! Only a qualified electrician can carry out the electrical installation
More informationSolar Hybrid Power Generating System CPS1200EOH12SC CPS2200EOH24SC CPS3000EOH24SC. User s Manual K01-C
Solar Hybrid Power Generating System CPS1200EOH12SC CPS2200EOH24SC CPS3000EOH24SC User s Manual K01-C000304-02 2 TABLE OF CONTENTS 1 IMPORTANT SAFETY INSTRUCTIONS..4 2 INSTALLATION....5 2-1 Unpacking...5
More informationPowerOhm Installation Manual for BM R Series Braking Modules
PowerOhm Installation Manual for BM R Series Braking Modules IMPORTANT: These instructions should be read thoroughly before installation. All warnings and precautions should be observed for both personal
More informationUser Manual V1.1 OptiFlex 1100 / OptiFlex 2000
User Manual V1.1 OptiFlex 1100 / OptiFlex 2000 Uninterruptible Power Supply System Table of Contents 1. Important Safety Warning 2 1-1. Transportation 2 1-2. Preparation 2 1-3. Installation 2 1-4. Operation
More informationKEWTECH. KT56 digital multi function tester. Instruction manual
KEWTECH KT56 digital multi function tester Instruction manual Contents 1 Safety Notice 1 2 Features and Principles of Measurement 3 3 Introduction 6 4 Specifications 7 5 Instrument layout 9 6 Operating
More informationAbstract. GLV Systems Test Plan 1
GLV Systems Test Plan 1 Abstract This document details the acceptance test plan for the Grounded Low Voltage system being developed for the LFEV design project. This is only a test plan draft, and will
More informationOWNER S MANUAL Please read this manual before operating your power supply
AC-DC POWER SUPPLY Switch Mode AC-DC Power Supply Model No. PSU-1210 PSU-1223 PSU-1230 OWNER S MANUAL Please read this manual before operating your power supply Table of Contents Precautions 2 Description
More informationFlight Systems. Replacement for KASSEC DESCRIPTION
DESCRIPTION The is a universal generator controller that will start, stop, and provide engine protection for most generators. Universal replacement for both the 90353 and 90354 KASSEC Compatible with most
More informationCompact High Voltage DC15 & DC30 POROSITY (HOLIDAY) DETECTORS
Operator s Handbook For Compact High Voltage DC15 & DC30 POROSITY (HOLIDAY) DETECTORS Can be used in accordance with: Australian Standard AS3894.1 ASTM G62, ASTM D5162, ASTM D4787, NACE RP0274, NACE SP0490,
More information362 Clamp Meter. Users Manual
362 Clamp Meter Users Manual PN 3622678 August 2010 2010 Fluke Corporation. All rights reserved. Printed in China. Specifications are subject to change without notice. All product names are trademarks
More informationTower Electronic Systems
3300 UPS Instruction Manual AUGUST 2005 CONTENTS 1.0 INTRODUCTION 1.1 General description 3 1.2 UPS building blocks 3 1.2.1 Boost converter 3 1.2.2 Inverter 3 1.2.3 Static transfer switch 3 1.2.4 Battery
More informationArt. No. EC-315. Art. No. EC-330. Art. No. EC-340 SWITCH-MODE BATTTERY CHARGER CONTENTS IMPORTANT SAFETY PRECAUTIONS... 2
SWITCH-MODE BATTTERY CHARGER CONTENTS IMPORTANT SAFETY PRECAUTIONS... 2 DESCRIPTION AND FEATURES... 3 CHARGING STAGES... 4 Art. No. EC-315 Art. No. EC-330 Art. No. EC-340 PROTECTIONS... 5 INSTALLATION...
More informationOPERATING INSTRUCTIONS
CM OPERATING INSTRUCTIONS 9 Function, Auto Range Digital Multi-Meter DM6450 INTERTEK Read this owner s manual thoroughly before use and save. C LISTED US I. DISPLAY FUNCTIONS & SYMBOLS 9 6 10 11 14 8 7
More informationSmart Battery Charger
BATTERY CHARGER Smart Battery Charger Model No. WSC-1215 (SB) WSC-1230 (SB) WSC-2408 WSC-2415 Manual Please read this manual carefully before installing and starting up this device. Figure 1 WSC-1215SB
More informationMonicon Instruments Co., Ltd. CHR-1285/2485 CHR-1285/2485 BATTERY CHARGER
CHR-1285/2485 BATTERY CHARGER TEL:886-4-2238-0698 FAX:886-4-2238-0891 Web Site:http://www.monicon.com.tw E-mail:sales@monicon.com.tw Copyright 2007 Monicon Instruments Co., Ltd. All right reserved. Contents
More informationTHT-500-A/R INSTRUCTION MANUAL TEMPERATURE AND HUMIDITY TRANSMITTER
INSTRUCTION MANUAL TEMPERATURE AND HUMIDITY TRANSMITTER THT-500-A/R No.THT51E1 2017.12 Thank you for purchasing our THT-500-A/R, Temperature and Humidity Transmitter (mounted within control panel). This
More information190M. Medical ScopeMeter. Safety Information
190M Medical ScopeMeter PN 4202934 June 2012, Rev. 1 2012 Fluke Corporation. All rights reserved. Printed in Romania. All product names are trademarks of their respective companies. WX Warning To prevent
More informationMatrix APAX. 380V-415V 50Hz TECHNICAL REFERENCE MANUAL
Matrix APAX 380V-415V 50Hz TECHNICAL REFERENCE MANUAL WARNING High Voltage! Only a qualified electrician can carry out the electrical installation of this filter. Quick Reference ❶ Performance Data Pages
More informationOutdoor vacuum breaker for railway applications - FSK II
Outdoor vacuum breaker for railway applications - FSK II Single or two-pole outdoor vacuum breaker with magnetic actuator 27.5 kv - 250 kv BIL - 1250 A. 2000 A - 25.0 ka - 50/60 Hz 27.5 kv - 200 kv BIL
More informationMatch 19" GE Digital Energy. Uninterruptible Power Supply VA. Technology for the Digital World. Match 19" UPS.
Match 19" Uninterruptible Power Supply 700-1500 VA Manufactured by: General Electric Company Telephone +41 (0)91 / 850 51 51 CH 6595 Riazzino (Locarno) Fax +41 (0)91 / 850 51 44 Switzerland Website www.gedigitalenergy.com
More information