SPECIFICATIONS OF Ni-Cd BATTERY BANK
|
|
- Doris Ellis
- 5 years ago
- Views:
Transcription
1 SPECIFICATIONS OF Ni-Cd BATTERY BANK ANNEXURE-Z Supply, Installation and commissioning of Ni-cd battery bank for high rate of discharge type KPH 125V 210 AH consisting of 103 number of cells. Detail technical specification is given below 1. IS/IEC CONFORMITY: Bank shall be supplied as per IS & IEC 623 with latest amendments. 2. SITE CONDITIONS: (a) Climate: Wet & Tropical (b) Temperature Range: 1.1 to +55 degree Celsius. (c) Electrical Ground Resistivity: Ohm Meter. (d) Relative Air Humidity: 100% Max (e) Site above MSL: Less than 1000 meters. (f) The atmosphere in the factory shall be laden with Urea dust. The air may contain Ammonia Vapors. 3. FEATURES: (a) The cells shall be vented type, assembled and end plastic container with covers. Covers shall be fitted with spray proof vent plugs. (b) All cell terminals shall be of adequate current carrying capacity. Cell terminal post shall be equipped with connector bolts. Cell terminal posts, Bolts and associated hardwares shall be electrolyte resisting material. (c) Electrolyte level indication lines for minimum and maximum levels shall be marked on maintenance access side of each jar or container. (d) Each battery shall be rated for specified ampere hours at five hours rate of discharge to end voltage of 1.00 volts per cell. (e) Nickel plated copper intercell connectors shall be used for connecting up adjacent cells and rows. Bolts, nuts and washers shall be nickel-plated steel/stainless steel. All terminals and cell inter-connectors shall be fully insulated or have insulation shrouds (f) Each cell shall be contained in close top container preferably transparent and unbreakable and shall incorporate positive and negative
2 plates and separators in position. Wooden separators shall not be acceptable. The cells shall be provided with inter cell connectors, Nut bolts along with two flat and one spring washer. Connector must be suitable to take full current and should be designed to withstand short circuit current also. Inter row, Inter Tier Connector and take off terminals shall be designed for rated current and shall also be able to withstand Short circuit current.. (g) The battery units shall be complete with all necessary components such as lids, plugs, separators and and buffers, inter cell connectors, cell insulators. (g) The required quantity of electrolyte plus 10% extra quantity complying relevant standards IS shall be supplied in suitable non returnable containers along with battery. 4. ACCESSORIES FOR MAINTENANCE You will supply the following accessories for maintenance along with main battery bank: (a) Syringe type hydrometer suitable for specific gravity readings 04 No s (b) Thermometer with specific gravity correction scale 02 No s (c) Cell Testing Voltmeter (3-0-3) complete with leads 02 No s (d) Insulated Spanners (For each type of battery) 02 sets (e) Rubber Syringe 02 No s (f) Funnel 02 No s (g) Jug 02 No s (h) Apron 02Nos (i) Rubber Gloves 02 sets (j) Teak Wood Stand For Hydrometers 02 Nos. 5. SPARES You will supply the following spares along with main battery bank: (a) Inter cell connectors- 10 No s (b) Vent plugs- 10 No s (c) Nuts & Bolts& Washers (2 flat and 1 Spring washer)- 10 Nos. 6. SPACE AVAILABLE FOR BATTERY STAND:
3 The battery bank being supplied by you has to be arranged in step type, three row stand with following limiting dimensions: Length: 2860mm, Width: 650mm, Height: 350mm approx.supply of battery stand shall be in party scope. 8. TEST 1.The Bidder shall have to submit along with offer, as pre-requisites, the complete Type test Reports of similar or higher rating battery bank, carried out within 5 years from the due date of Tender, from CPRI/NABL accredited/govt. recognized Test House failing which their offer may not be technically acceptable. 2. Guaranteed Test Particulars annexure 2 shall be duly filled and submitted along with offer. 2. Routine Test & Acceptance test certificates as per IS shall be furnished by the party along with the supply of material 3. Capacity test of the supplied battery bank shall be carried out by the party as per IS BUYBACK OF USED/UNSERVICEABLE BATTERIES Manufacturer shall buyback used/unserviceable batteries of similar rating from the substations where batteries are replaced. The bidder should quote their rates for buyback of old battery bank. 10. DOCUMENTS Documents, Test Certificates, Drawing etc. along with operational and maintenance Manuals, complete charging, initial charging, discharging procedure shall be supplied along with battery banks/ dispatch documents as per Annexure III.
4 TECHNICAL PARTICULARS TO BE FILLED BY PARTY Sr. No. 125 Volts, 210AH, 103 Cells Ni-Cd Battery Bank To be filled by party 1. Manufacturer Name 2. Country Of Manufacturer 3. Type Of Battery 4. Reference Standards For Construction and performance 5. No. of cells 6. Nominal Voltage Of Battery 7. Finishing rate of Charge (A) 8. Voltage per cell at the end of charge at the finishing rate 9. Voltage of each cell on complete discharge at 10 hour rate 10. Open circuit voltage of each cell on full charge (volts) 11. Internal Resistance Per cell (milli ohm per cell) 12. Minimum voltage per cell at which it can be operated at 20hour rate of discharge 13. Requirement of First Charge (Ampere Hour) 14. Discharge Capacity in Ampere Hour a) 5 Hour rate to 1.14 volts per cell b) 3 Hour rate to 1.10 volt per cell c) 1 Hour rate to 1.06 volt per cell d) 30 minutes discharge rate to 1 volt per cell e) 15 minutes discharge rate to 0.85 volt per cell f) 5 minutes discharge rate to 0.65 volt per cell
5 g) 1 minute discharge rate to 0.65 volt per cell 15. Guarantee efficiency on 10 hour rate in terms of watt hour 16. Type of positive plate per cell 17. No. of positive plates per cell 18. Type of negative plate per cell 19. No. of negative plates per cell 20. Size of positive plates (mm) 21. Size of negative plates (mm) 22. Fully charge specific gravity of electrolyte 23. Slow Charging Rate (A) 24. Quick Charging Rate (A) 25. Float Charging Voltage per cell (V/cell) 26. Size and material of connectors and method of connection between cells a) Inter cell (mm) b) Inter row c) Inter stand d) Take off e) Stud/Bolts, Nut and Washer 27. Type of Separators 28. Thickness of Separator (mm) 29. Material and Size of Container (mm) 30. Clearance between the bottom of plates and containers (mm) 31. Battery mild steel supporting rack dimensions(mm) 32. Amount and specific gravity of Electrolyte per cell required for first filling (litres/cell)
6 33. Weight of complete cell with Electrolyte(KG) 34. Type of Venting 35. Self Life 36. Expected Life a) For cyclic use(in terms of no. of charge/discharge) b) For use under float (trickle charge) 37. Operating Temperature Range 38. Type of cell arrangement
7 Documents to be submitted in different stage of Tender Sr No. DOCUMENTATION With the Quotation for approval After Order No. of Copies Final No. of Copies 1. General arrangement drawing showing the arrangement of the battery 2. Illustrative and descriptive technical literature 3. Installation, operation and Maintenance Manual Type Test Certificate Routine Test & Acceptance Test Certificates Guarantee Certificate Technical Particulars 1 3 NOTE: All final documents shall be furnished in superior quality files.
ANNEXURE XI. (Ni Cd Battery Bank) TECHNICAL SPECIFICATIONS OF 125V STATION BATTERY BANK OF GTG I.
ANNEXURE XI (Ni Cd Battery Bank) TECHNICAL SPECIFICATIONS OF 125V STATION BATTERY BANK OF GTG I. Sr. No Technical Particulars Confirmation to be given by bidder (Please strike out which ever not applicable)
More informationSPECIFICATIONS FOR 50 V, 600 AH LEAD ACID BATTERY
(I) INTRODUCTION: Power Line Carrier Communication (PLCC) System is being used by Gujarat Energy Transmission Corporation Ltd. for Speech, Data, Protection and Teleprinter signal transmission purpose throughout
More informationGUJARAT ENERGY TRANSMISSION CORPORATION LTD. TECHNICAL SPECIFICATIONS. 110 V, 100 Ah / 250 Ah & 220 V, 250 Ah / 350Ah TUBULAR LEAD ACID BATTERY SETS
GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATIONS FOR 110 V, 100 Ah / 250 Ah & 220 V, 250 Ah / 350Ah TUBULAR LEAD ACID BATTERY
More informationSection V DC Nickel Cadmium Alkaline BATTERY
Section - 7 TECHNICAL SPECIFICATION OF 110V DC Nickel Cadmium Alkaline BATTERY TECHNICAL SPECIFICATIONS & REQUIREMENTS OF 110V DC Nickel Cadmium Alkaline Battery 7. 1 GENERAL This section of the document
More informationTECHNICAL SPECIFICATION FOR 30 V, 100 AH STATIONARY BATTERIES AND BATTERY CHARGING EQUIPMENT. (SPECIFICATION NO. MSEB/Dist/IV/2004.
TECHNICAL SPECIFICATION FOR 30 V, 100 AH STATIONARY BATTERIES AND BATTERY CHARGING EQUIPMENT (SPECIFICATION NO. MSEB/Dist/IV/2004.) MAHARASHTRA STATE ELECTRICITY DISTRIBUTION COMPANY LTD. PAGE 1 OF 18
More informationSECTION 1 SCOPE, SPECIFIC TECHNICAL REQUIREMENT AND QUANTITIES
Tamil Nadu Transmission Corporation Limited Bharat Heavy Electricals Limited 400/110 KV Substation at Thappagundu & 400/230-110 KV Substation at Anikadavu, Technical specification for 420/245/132kV Isolators
More information020: 2013 CEB SPECIFICATION MINIATURE CIRCUIT BREAKER (MCB)
020: 2013 CEB SPECIFICATION MINIATURE CIRCUIT BREAKER (MCB) CEYLON ELECTRICITY BOARD SRI LANKA Telephone: +94 11 232 0953 Fax: +94 11 232 3935 CONTENTS Page 1.0 Scope 3 2.0 System Parameters 3 3.0 Service
More informationCAMTECH/S/2005/LAC/2.0 1 LEAD ACID CELL
CAMTECH/S/2005/LAC/2.0 1 1. Introduction LEAD ACID CELL Two different types of lead acid cells are manufactured by the industry and depending on the application, these are normally referred to as mobile
More informationTECHNICAL SPECIFICATION FOR 11 KV CAPACITOR BANK
TECHNICAL SPECIFICATION FOR 11 KV CAPACITOR BANK MAHARASHTRA STATE ELECTRICITY DISTRIBUTION COMPANY LTD. PAGE 1 OF 7 TECHNICAL SPECIFICATION FOR 11 KV.CAPACITOR BANK 1.0 SCOPE: This specification covers
More informationSPECIFICATION FOR REWIRABLE FUSES (KITKAT FUSES) 100A & 200A SPECIFICATION NO.: DIST/ A- KIT /
SPECIFICATION FOR REWIRABLE FUSES (KITKAT FUSES) 100A & 200A SPECIFICATION NO.: DIST/ A- KIT / 2005-06 SR.NO ITEM PAGE 1. SCOPE 2 2. WEATHER CONDITIONS 2 3. RATED VOLTAGE & FREQUENCY 2 4. GENERAL REQUIREMENT
More informationNCPP. Nickel Cadmium Pocket Plate Batteries. Single Cell Catalogue
NCPP Nickel Cadmium Pocket Plate Batteries Single Cell Catalogue Introduction: HBL s Nickel Cadmium Pocket Plate battery designs are based on the superior pocket plate technology. A fully integrated modern
More informationCITY OF CHARLEVOIX REQUEST FOR BIDS WESTENBROEK SUBSTATION 48VDC BATTERY BANK
CITY OF CHARLEVOIX REQUEST FOR BIDS WESTENBROEK SUBSTATION 48VDC BATTERY BANK The City of Charlevoix is requesting bids for the furnishing and delivery (F.O.B. project material site, Charlevoix, Michigan)
More information017: 1998 CEB STANDARD RING MAIN UNIT CEYLON ELECTRICITY BOARD SRI LANKA
017: 1998 CEB STANDARD RING MAIN UNIT CEYLON ELECTRICITY BOARD SRI LANKA CONTENTS PAGE 1. Scope 2 2. System Parameters 2 3. Service Conditions 2 4. Applicable Standards 3 5. Basic Features 4 6. Quality
More informationSPECIFICATION FOR POWER BATTERIES
KAKRAPAR ATOMIC POWER STATION UNITS & (0 MWe) PROCUREMENT SPECIFICATION NO. KAPS/534/PB SEPC./00 SPECIFICATION FOR POWER BATTERIES Prepared By: Checked By: Reviewed By: Approved By: Kapil Mishra SO/E,
More informationMaterial Description Quantity UOM
Page : 1 / 8 OIL INDIA LIMITED Fax-91 0361 2643686 (A Govt. of India Enterprise) Email-oilmatpl@oilindia.in Udyan Vihar, Narengi, Guwahati, Assam 10 99070701 BATTERY 12 V 65AH Sealed Maintenance Free (SMF)
More information026-2 : 1996 CEB STANDARD
026-2 : 1996 CEB STANDARD COMPRESSION CONNECTORS & TERMINATIONS FOR OVERHEAD LINE CONDUCTORS CEYLON ELECTRICITY BOARD SRI LANKA CONTENTS 1. Scope 2 2. System Parameters 2 3. Service Conditions 2 4. Applicable
More information013 : 2009 CEB SPECIFICATION MOULDED CASE CIRCUIT BREAKERS
013 : 2009 CEB SPECIFICATION MOULDED CASE CIRCUIT BREAKERS FOR OVERHEAD NETWOKS CEYLON ELECTRICITY BOARD SRI LANKA Specification for MOULDED CASE CIRCUIT BREAKERS FOR OVERHEAD NETWOKS CEB Specification
More informationPURE LEAD PLUS UPS APPLICATIONS. Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications Watts per Cell
UPS 12-1121 PURE LEAD PLUS Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications 305-545 Watts per APPLICATIONS Data Centers Network Operations Centers Industrial Process Control
More informationSwitchgear Utility specific gravity nominal sulfuric acid. 10 years, full float service at 77 F (25 C)
12-373 UL Recognized Component RETURN LEAD RECYCLE LIBERTY SERIES 1000 VALVE REGULATED LEAD-CALCIUM BATTERY FOR STANDBY APPLICATIONS Capacities from 100 to 600 Ampere-hours (8 hours to 1.75 VPC) 343 to
More informationKPM type Intended for medium discharge currents from 0.5 to 2 C
KPM type Intended for medium discharge currents from 0.5 to 2 C APPLICATION: -Railway: Traction cars, VIP cars, etc. -Mines: Mining locomotives -Factories and institutions: Electro-carets, certain types
More informationVentPro Reduced Maintenance Nickel Cadmium Batteries for Stationary Applications
VentPro Reduced Maintenance Nickel Cadmium Batteries for Stationary Applications Dimensional and Electrical Data Rev. 02-16 Storage Battery Systems LLC N56 W16665 Ridgewood Dr. Menomonee Falls, WI 53051
More informationNPS/003/002 Technical Specification for 30V Distribution Tripping Battery and Charger Systems
Version:- 2.1 Date of Issue:- July 2016 Page 1 of 29 NPS/003/002 Technical Specification for 30V Distribution Tripping Battery and Charger Systems 1. Purpose This document is to detail the technical requirements
More informationStandards are finally approved by the Standards High Council of Iranian Ministry of Petroleum.
FOREWORD This Standard is intended to be used within and for Iranian Ministry of Petroleum (N.I.O.C, N.I.G.C, N.P.C., N.I.O.R.D.C. and other affiliate organizations and companies) and has been prepared
More informationSupply of 63 kva DIESEL GENERATOR SET WITH AMF
No. NIQ/INKEL/2015-16/162 24 TH Nov 2015 NOTICE INVITING QUOTATION Sealed Quotations are invited for and on behalf of INKEL Limited, having its registered office at INKEL Centre, Off Vallathol junction,
More informationNCPP. Nickel Cadmium Pocket Plate Batteries. Single Cell Dimensional and Electrical Data
NCPP Nickel Cadmium Pocket Plate Batteries Single Cell Dimensional and Electrical Data Nickel Cadmium Pocket Plate Batteries HBL's Nickel Cadmium Pocket Plate Battery designs are based on the superior
More informationTechnical Specification for 33 KV 200 AMPs,H.G,Fuse set.
Technical Specification for 33 KV 200 AMPs,H.G,Fuse set. 1. SCOPE:- This specification covers the manufacture, testing and supply of 33KV 200 Amps, H.G. Fuse sets 2. The 33 KV H.G. Fuses shall be suitable
More informationNi-Cd Batteries. Solutions for the toughest requirements
I N T E L L I G E N T S Y S T E M S Ni-Cd Batteries Solutions for the toughest requirements Triathlon Ni-Cd Batteries cell Construction Gas drying or flame arresting vent Safety terminal Redundant leak
More informationTECHNICAL SPECIFICATION FOR 11 KV AUTOMATIC CAPACITOR SWITCH
TECHNICAL SPECIFICATION FOR 11 KV AUTOMATIC CAPACITOR SWITCH MAHARASHTRA STATE ELECTRICITY DISTRIBUTION COMPANY LTD. PAGE 1 OF 7 TECHNICAL SPECIFICATION FOR 11 KV AUTOMATIC CAPACITOR SWITCH 1.0 SCOPE:
More informationSUBSTATION EQUIPMENT - Page 1 of 8
BATTERY BANKS 1. GENERAL: JEA utilizes a 125 volt DC system for the control and operation of its transmission and distribution substations. JEA has standardized on lead acid type battery banks to supply
More informationFeatures and Benefits
C&D Tubular GEL (OPzV) Series For Standby & Cyclic Applications C&D Tubular GEL (OPzV) Series range of valve regulated lead acid stationary batteries combine the benefits of recombination technology (i.e.
More informationLIBERTY SERIES 1000 VALVE REGULATED LEAD-CALCIUM BATTERY For standby applications Capacities from 25 to 600 Ampere-hours
RETURN RECYCLE 12-373 LEAD LIBERTY SERIES 1000 VALVE REGULATED LEAD-CALCIUM BATTERY For standby applications Capacities from 25 to 600 Ampere-hours UL Recognized Component C&D Technologies Powercom Division
More informationTender documents for supply, erection & commissioning of Plante Type Battery to 2x210 MW IB Thermal Power Station.
ORISSA POWER GENERATION CORPORATION LIMITED IB THERMAL POWER STATION AT/P.O: BANHARPALI, DIST: JHARSUGUDA, PIN: 768234 (ORISSA), INDIA GRAM: IB THERMAL, TEL: 06645-222209/222210, FAX: 06645-222209/54/30
More information023 : 2006 CEB STANDARD. 12kV & 36kV LOAD BREAK SWITCHES CEYLON ELECTRICITY BOARD SRI LANKA
023 : 2006 CEB STANDARD 12kV & 36kV LOAD BREAK SWITCHES CEYLON ELECTRICITY BOARD SRI LANKA Specification for 12kV & 36kV LOAD BREAK SWITCHES CEB Standard 023 : 2006 CEYLON ELECTRICITY BOARD No. 50, Sir
More informationNCPP. Nickel Cadmium Pocket Plate Batteries. Block Cell Dimensional and Electrical Data
NCPP Nickel Cadmium Pocket Plate Batteries Block Cell Dimensional and Electrical Data Nickel Cadmium Pocket Plate Batteries HBL's Nickel Cadmium Pocket Plate Battery designs are based on the superior Pocket
More informationشركة كهرباء محافظة القدس المساهمة المحدودة
Our Ref: Date: Messrs. Dear Sir, Tender 22/2017 (re-bidding) 11& 33Kv Fuse Cutouts and Links You are kindly requested to bid for supply and delivery (DDP) for the medium voltage overhead line accessories
More informationTechnical Specifications
LT Distribution Box Technical Specifications 1. SCOPE 1.1 This specification covers design, manufacture, testing at manufacturer works before dispatch and supply of L.T. Distribution Cabinet suitable for
More informationSTANDARDIZATION ORGANIZATION FOR G.C.C (GSO) GSO 34/2007
STANDARDIZATION ORGANIZATION FOR G.C.C (GSO) GSO 34/2007 LEAD-ACID STARTER BATTERIES USED FOR MOTOR VEHICLES AND INTERNAL COMBUSTION ENGINES ICS: 43.040.00 LEAD-ACID STARTER BATTERIES USED FOR MOTOR VEHICLES
More informationINVITATION TO TENDER MR 84/2016. SUPPLY and Install 110V DC BATTERY BANKS and CHARGERS for Rarawai, Sabeto and Lautoka Switching Station
INVITATION TO TENDER MR 84/2016 SUPPLY and Install 110V DC BATTERY BANKS and CHARGERS for Rarawai, Sabeto and Lautoka Switching Station Fiji Electricity Authority seeks reputable Manufacturer/Supplier
More informationFLOAT CHARGER (40A) & BOOST CHARGER (35A) FOR NO BREAK POWER SUPPLY SYSTEM WITH REQUIREMENT FOR SCADA
GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATIONS FOR FLOAT CHARGER (40A) & BOOST CHARGER (35A) FOR GETCO/E/TS-50V BCHR(SCADA)
More informationGASTON GTF range battery manual
GASTON GTF range battery manual Type 1. Brief introduction GTF stationary lead-acid battery (acid spray-proof type), ranging from 200ah to 3000ah at 10hr rate in 17 models, are mainly applied in power
More informationValve Regulated Lead Acid (VRLA) Battery Series Designed for UPS Standby Power Applications FEATURES & BENEFITS
12-1079 HIGH RATE MAX UPS 12-355MRF APPLICATIONS Data Centers Network Operations Centers Industrial Process Control Facilities Internet Housing Sites Semiconductor Manufacturing Banks & Financial Markets
More informationVRLA Batteries. Battery Installation And Start up Guide
TECHNICAL MANUAL 41-7525 VRLA Batteries 26-206 Ampere-Hour Capacity Battery Installation And Start up Guide (For Rack Mounted Systems) 41-7525/0514/CD www.cdtechno.com Table of Contents 12V VRLA Battery
More information045 : 2000 CEB STANDARD
045 : 2000 CEB STANDARD LOW VOLTAGE FUSE SWITCH DISCONNECTOR CEYLON ELECTRICITY BOARD SRI LANKA Specification for LOW VOLTAGE FUSE SWITCH DISCONNECTOR CEB Standard 045 : 2000 CEYLON ELECTRICITY BOARD No.
More informationPURE LEAD PLUS UPS APPLICATIONS Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications Watts per Cell
-11 PURE LEAD PLUS Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications 305-545 Watts per Cell FEATURES & benefits APPLICATIONS Data Centers Network Operations Centers Industrial
More information(High Pressure Boiler Plant) Tiruchirappalli , TAMIL NADU, INDIA MATERIALS MANAGEMENT / CAPITAL EQUIPMENT. Enquiry Date:
10111. 4711M1 An ISO 9001 Company Bharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli 620014, TAMIL NADU, INDIA MATERIALS MANAGEMENT / CAPITAL EQUIPMENT ENQUIRY Corrigendum 1
More informationPOWER-plus. Ni-Cd XHP. Capacity: 10 Ah to 250 Ah
Ni-Cd XHP Capacity: 10 Ah to 250 Ah XHP Range Low maintenance, high performance Ni-Cd batteries Powerful assurance for critical applications Depend upon XHP series where vital UPS, engine starting and
More information34-SDMS-01 SPECIFICATIONS FOR
SPECIFICATIONS FOR M V DROPOUT FUSE CUT OUTS This specification is property of SEC and subject to change or modification without any notice CONTENTS C l a u s e s: Page No. 1- SCOPE 3 2- CROSS REFERENCES
More informationSTR-1415 SPECIFICATION FOR BATTERY CHARGERS 220V, 30A FOR SUBSTATIONS ANNEXURES B
STR-1415 SPECIFICATION FOR BATTERY CHARGERS 220V, 30A FOR SUBSTATIONS ANNEXURES B February 2017 STR-1415 SPECIFICATION FOR BATTERY CHARGERS 220V, 30A FOR SUBSTATIONS ANNEXURES B DRAFT FINAL DRAFT CONTRACT
More informationTECHNICAL SPECIFICATION
SECTION - III TECHNICAL SPECIFICATION OF AB SWITCH & HG FUSE NESCO : TN/ 17427/14.11.11-1 - 1. 33 KV 200 Amp 3 Pole HG Fuse (Horizontal Mounting Type) Quantity 15 Sets Technical Specification 1. SCOPE:
More informationSPECIFICATION FOR VT D 70 CONTENTS
CONTENTS 1/ SCOPE 2/ GENERAL ELECTRICAL CHARACTERISTICS 3/ GENERAL MECHANICAL CELL SPECIFICATION 4/ CAPACITY 5/ CHARGE RECOMMENDATIONS 6/ CYCLE LIFE 7/ CELL AND BATTERY MANAGEMENT 8/ SPECIFICATION APPROVALS
More informationTECHNICAL SPECIFICATION FOR SHACKLE HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV LINE
TECHNICAL SPECIFICATION FOR SHACKLE HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV LINE The hardware fittings suitable for tension string to be used for 11KV consisting of following
More informationFLOAT CHARGER & BOOST CHARGER F O R NO BREAK POWER SUPPLY SYSTEM (Float 100A & Boost 60 A with SCADA application)
GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATIONS FOR FLOAT CHARGER (100A) & BOOST CHARGER (60A) FOR WITH REQUIREMENT FOR SCADA
More informationStandby Products SD-SDH. series. Technical Features. Applications. Product Features
SD-SDH series The FIAMM s SD-SDH battery range can be used in standby mode for duties requiring high performance and reliability. The SD-SDH family is specially designed for discharge rates that are required
More informationTubular Flooded (OPzS) Batteries
Tubular Flooded (OPzS) Batteries Stationary & Renewable Energy Applications BATTERIES SOLAR PV WIND GENSET Overview Vented Tubular Plate Batteries for Stationary & RES Applications Discover RE Tubular
More informationSD / SDH. Applicable Standards. Applications and Key Benefits. FIAMM Manufacturing. - Technical Features
Applications and Key Benefits 2V cells - 80Ah to 2320Ah nominal capacity Ideal for: - Power generation and distribution - Electrical Utilities /Switchgear - UPS & datacenter systems - Railway crossing,
More informationBharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli , TAMIL NADU, INDIA CAPITAL EQUIPMENT / MATERIALS MANAGEMENT
An ISO 9001 Company Bharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli 620014, TAMIL NADU, INDIA CAPITAL EQUIPMENT / MATERIALS MANAGEMENT ENQUIRY NOTICE INVITING TENDER Phone:
More informationSPECIFICATION FOR AUTOMATIC PRIMING AND OPERATING SYSTEM FOR CENTRIFUGAL PUMPS.
DRAFT SPECIFICATION NO : RDSO/PE/SPEC/D/PS/0010-99 (REV. 0 ) SPECIFICATION FOR AUTOMATIC PRIMING AND OPERATING SYSTEM FOR CENTRIFUGAL PUMPS. 0. FOREWORD 0.1 This specification covers manufacturing and
More informationD.C. DISTRIBUTION BOARD
PRAMBL: The TC is maintaining 50-volt battery backup system for the PLCC communication. The 50-volt D.C. supply from the Float cum Boost charger is brought to D.C. Distribution Board from where supply
More information66 kv SF6 CIRCUIT BREAKER (SPRING OPERATED)
GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATION FOR 66 kv SF6 CIRCUIT BREAKER (SPRING OPERATED) GETCO/E/06TS CB/R3 May12 Page
More information34-SDMS-02 SPECIFICATIONS FOR
SPECIFICATIONS FOR M V & L V FUSE LINKS This specification is property of SEC and subject to change or modification without any notice TABLE OF CONTENTS 1.0 SCOPE 3 2.0 CROSS REFERENCES 3 3.0 APPLICABLE
More informationPOWER FOR TOMORROW. Motive Power. Network Power. Chargers. Bloc Batteries. Accessories. Service
POWER FOR TOMORROW TODAY The Eternity Technologies range is built using only the highest quality and most efficient production processes at our state-of-the-art manufacturing centre in the UAE. It is this
More information33 KV STATIC SHUNT CAPACITOR WITH ALLIED EQUIPMENT
33 KV STATIC SHUNT CAPACITOR WITH ALLIED EQUIPMENT September 2017 Engineering Department WEST BENGAL STATE ELECTRICITY TRANSMISSION COMPANY LIMITED Regd. Office: VidyutBhawan, Block DJ, Sector-II, Bidhannagar,
More informationBHARAT HEAVY ELECTRICALS LIMITED Industrial Valves Plant Goindwal (AMRITSAR) Enquiry Date:
BHARAT HEAVY ELECTRICALS LIMITED Industrial Valves Plant Goindwal 143422 (AMRITSAR) ENQUIRY Phone:+91 1859 223381 (+91 1859 222002, 222036, 222039 Extn 117) Fax :+91 1859 222 061 Email :srk@ivp.bhel.co.in
More informationVented fibre structure Nickel Cadmium batteries for stationary systems
Vented fibre structure Nickel Cadmium batteries for stationary systems FNC FNC Vented Nickel Cadmium Batteries the best solution for long, reliable battery life FNC Nickel Cadmium single cells are designed
More informationTECHNICAL SPECIFICATIONS FOR 11KV AIR BREAK (A.B.) SWITCHES :
TECHNICAL SPECIFICATIONS FOR 11KV AIR BREAK (A.B.) SWITCHES : 1. SCOPE : This specification covers design, manufacturing, testing at manufacturer s works, inspection, packing & delivery of 11 KV Air Break
More informationNi-Cd Battery Product Specification
Ni-Cd Battery Product Specification SC1600 1. This specification governs the performance of the following Nickel-Cadmium Cylindrical cell and its stackup battery. SC BATTERY 16NC50 (To include all 1.6Ah
More informationSupply, Installation and Commissioning of 1 No 50 Watt LED. based SPV SLS at Nadia District Library, Krishna Nagar, Nadia.
Supply, Installation and Commissioning of 1 No 50 Watt LED based SPV SLS at Nadia District Library, Krishna Nagar, Nadia. TENDER DOCUMENT. (A Govt. of West Bengal Company) Bikalpa Shakti Bhavan, Plot J1/10,
More informationTechnical Specification of 11KV 200Amp. (3-Pole/2-Pole) Air Break Switch Scope Description of the materials Standards Insulator make
Technical Specification of 11KV 200Amp. (3-Pole/2-Pole) Air Break Switch 1. Scope:- This specification covers manufacturing, testing and supply of 11KV 200Amp. 50Hz Air Break switches for outdoor installation
More informationFEATURES & benefits. Constant Power Discharge Ratings - Watts per 77 F (25 F) Operating Time (in minutes) to 1.
-1029 Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications. APPLICATIONS Data Centers Network Operations Centers Industrial Process Control Facilities Internet Housing Sites Semiconductor
More informationSPECIFICATIONS OF SINGLE GIRDER UNDER SLUNG E.O.T. CRANE CAPACITY: 5 MT
1 SPECIFICATIONS OF SINGLE GIRDER UNDER SLUNG E.O.T. CRANE CAPACITY: 5 MT QUALIFICATION CRITERIA Vendor has to compulsorily meet the following requirements to get qualified for consideration of the technical
More informationBharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli , TAMIL NADU. INDIA CAPITAL EQUIPMENT/ MATERIALS MANAGEMENT
An ISO 9001 Company ENQUIRY Bharat Heavy Electricals Limited (High Pressure Boiler Plant) Tiruchirappalli 620014, TAMIL NADU. INDIA CAPITAL EQUIPMENT/ MATERIALS MANAGEMENT NOTICE INVITING TENDER Phone:
More informationTECHNICAL SPECIFICATIONS
GUJARAT ENERGY TRANSMISSION CORPORATION LTD. SARADAR PATEL VIDYUT BHAVAN, RACE COURSE, BARODA 390 007. TECHNICAL SPECIFICATIONS FOR SELECTIVE LEVEL METER GETCO/E/TS- PACC SLM 03504/R0, Dt: 2.04.2008 Page
More informationPIBAS Ni-Cd cells can be assembled into many different configuration forms, for example:
Range Summary Ni-Cd KL P/KM P/KH P Ni-Cd Standard Range Batteries PIBAS Ni-Cd Batteries Advantages of PIBAS Ni-Cd batteries Based on the more than 130 years of experience PIBAS KL P/KM P/KH P ranges are
More informationSOMALI ENERGY TRANSFORMATION (SET) PROJECT
SOMALI ENERGY TRANSFORMATION (SET) PROJECT Solar PV installation BOQ JUNE 2016 School 1. Gob Secondary School- Awdal Region. 2. Godmo Biyo CAS Primary School Sanaag Region. 3. Lafarug Primary School- Sahil
More informationSPA AGM VRLA batteries
SPA AGM VRLA batteries for Stationary Applications SPA OVERVIEW Valve Regulated AGM batteries The SPA range of SUNLIGHT Valve Regulated Lead Acid batteries has been developed as general purpose batteries,
More informationTECHNICAL SPECIFICATION FOR 11 KV AIR BREAK (A.B.) SWITCHES:
TECHNICAL SPECIFICATION FOR 11 KV AIR BREAK (A.B.) SWITCHES: 1. SCOPE : This specification covers design, manufacturing, testing at manufacturer s works, inspection, packing & delivery of 11 KV Air Break
More informationScope of Supply of 11Kv Induction motor. The motor is being procured for cooling water pump. The scope of supply of motor is as given below:
Scope of Supply of 11Kv Induction motor Annexure Z The motor is being procured for cooling water pump. The scope of supply of motor is as given below: 1. Design, manufacture, supply and testing of Energy
More informationNLC INDIA LIMITED (formerly Neyveli Lignite Corporation Limited) ('NAVARATNA'-Government of India Enterprise) MATERIALS MANAGEMENT COMPLEX
NLC INDIA LIMITED (formerly Neyveli Lignite Corporation Limited) ('NAVARATNA'-Government of India Enterprise) MATERIALS MANAGEMENT COMPLEX Dr. Rajendra Prasad Road,Block-27,Neyveli-607807.Tamilnadu,India.
More information4.1 Type of the valve and materials of construction of body and trim shall be as specified in valve Data sheet.
SHEET 1 OF 5 1.0 GENERAL & SCOPE 1.1 This specification covers the design, material, construction features, manufacture, inspection & testing, Painting and packing requirements of Spring Loaded Bypass
More informationZAVOD AIT Nickel-Cadmium Cells and Batteries
ZAVOD AIT Nickel-Cadmium Cells and Batteries AIT Ni-Cd cells and batteries Quality in everything we do We work for opportunity in full volume and for reasonable price to provide with modern cell batteries
More informationRange. Alcad Single Cell Range. Powerful assurance for maximum operating reliability
inglecell Range Alcad Single Cell Range Powerful assurance for maximum operating reliability Alcad Single Cell Range the reliability you need at the heart of your power backup system. Versatility for industry
More informationAINO MICRO RANGE VRLA. Compact energy for increased security BATTERY SOLUTIONS. EverExceed power your applications
EverExceed power your applications Maintenance free VRLA design Leak proof / Spill proof Gas recombination Absorbed electrolyte Float / Cycle use Low self-discharge rate Reliable one-way safety valve Lead
More informationTECHNICAL SPECIFICATION FOR 11 KV DROP OUT (D.O.) FUSE with Polymeric Insulators:
TECHNICAL SPECIFICATION FOR 11 KV DROP OUT (D.O.) FUSE with Polymeric Insulators: (1) SCOPE: This specification covers outdoor, open, drop out expulsion type fuse cut outs suitable for installation in
More informationUPS FEATURES & BENEFITS TECHNICAL DATA Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications.
41-9027 Valve Regulated Lead Acid Battery Designed for UPS Standby Power Applications. TECHNICAL DATA FEATURES & BENEFITS 10 year design life @ 25 C Absorbent Glass Mat (AGM) technology for efficient gas
More information2 Volt AGM Range. Haze Battery Company Ltd
2 Volt AGM Range Haze Battery Company Ltd Q Q M M The Haze HZB - AGM range covers Ah capacities from 50Ah to 3850Ah (C10) with dimensions suitable for racking systems for maximum space utilisation. Specially
More informationMANUAL 4. The Norms set for discharge of its Function
MANUAL 4 The Norms set for discharge of its Function i. For the achievement of Organizational Objectives, each department has formulated its own norms based on various standards like Engineering, Accounting
More informationReference Number PDS 18 - (RIC Standard: EP SP)
Discipline Engineering Standard - NSW Category Electrical Title Reference Number PDS 18 - (RIC Standard: EP 06 00 00 01 SP) Document Control Status Date Prepared Reviewed Endorsed Approved Jan 05 Standards
More information33KV INDOOR SWITCHGEAR
33KV INDOOR SWITCHGEAR September 2017 Engineering Department WEST BENGAL STATE ELECTRICITY TRANSMISSION COMPANY LIMITED Regd. Office: VidyutBhawan, Block DJ, Sector-II, Bidhannagar, Kolkata 700091. CIN:
More informationSPECIAL SPECIFICATION 6576 Solar Panel Power Supply System
2004 Specifications CSJ 1068-04-126, 0197-02-108 SPECIAL SPECIFICATION 6576 Solar Panel Power Supply System 1. Description. This work shall consist of furnishing and installing an integrated solar Panel
More informationTubular Flooded (OPzS) Batteries
Tubular Flooded (OPzS) atteries Stationary & Renewable Energy pplications TTERIES SOLR PV WIND GENSET Overview Vented Tubular Plate atteries for Stationary & RES pplications Discover RE Tubular Flooded
More informationVRPP. Nickel Cadmium Valve regulated Pocket Plate Batteries. Dimensional and Electrical Data
VRPP Nickel Cadmium Valve regulated Pocket Plate Batteries Dimensional and Electrical Data The Valve Regulated Pocket Plate (VRPP) battery combines the unmatched reliability of Nickel Cadmium pocket plate
More informationSPECIFICATION FOR HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV/22KV LINE
SPECIFICATION FOR HARDWARE FITTINGS SUITABLE FOR TENSION STRING TO BE USED FOR 11KV/22KV LINE The hardware fittings suitable for tension string to be used for 11KV / 22 KV consisting of following components.
More informationSPECIFICATION FOR BATTERY & BATTERY CHARGER (D.C. SYSTEM)
Doc No: 256324-500-SP-ELE-006 Rev: A Page 1 of 11 SPECIFICATION FOR BATTERY & BATTERY CHARGER (D.C. SYSTEM) Doc No: 256324-500-SP-ELE-006 Rev: A Page 2 of 11 List of Contents Pages 1.0 Scope...3 2.0 Technical
More informationLDP MP. Ni-Cd single cells. LD P - M P ranges Capacity: 10 Ah to 70 Ah L2.4. Benefits
L2.4 Ni-Cd single cells LD P - M P ranges Capacity: 10 Ah to 70 Ah LDP MP Nickel-cadmium single cells are designed for general purpose applications, where maximum operating reliability is a key factor:
More informationNICKEL-CADMIUM POCKET TYPE ALKALINE STORAGE BATTERY
MANUAL OF OPERATION AND MAINTENANCE FOR NICKEL-CADMIUM POCKET TYPE ALKALINE STORAGE BATTERY 1/18 CONTENTS 1. Applications. (3) 2. Main properties of the cell and the battery.... (3) 3. Main performance
More informationHARYANA VIDYUT PRASARAN NIGAM LTD.
HARYANA VIDYUT PRASARAN NIGAM LTD. TECHNICAL SPECIFICATION SSD/S-03/R-1/DGM-605 TECHNICAL SPECIFICATION FOR 33 KV CAPACITOR BANKS CHIEF ENGINEER/MM HVPNL, PANCHKULA TELEPHONE & FAX: 0172-2583724 MARCH-2017-0
More informationTechnical Specification
Section - 7 Technical Specification OF 33KV OUTDOOR DROP OUT FUSE CUT-OUT AND FUSE LINK AND 33KV OUTDOOR TYPE SINGLE PHASE METAL OXIDE (ZNO) GAPLESS LIGHTNING ARRESTER 84 7.1. TECHNICAL SPECIFICATION OF
More informationXHP. Low maintenance high performance batteries
Low maintenance high performance batteries Range Low maintenance, high performance Ni-Cd batteries Powerful assurance for critical applications Depend upon where vital UPS, engine starting and emergency
More information31-SDMS-01 REV. 03 SPECIFICATIONS FOR
31-SDMS-01 REV. 03 SPECIFICATIONS FOR LOW VOLTAGE DISTRIBUTION PANEL This specification is property of SEC and subject to change or modification without any notice CONTENTS Clauses: Page No. 1.0 SCOPE
More informationDakshin Gujarat Vij Company Limited
Dakshin Gujarat Vij Company Limited CIN U40102GJ2003SGCO42909 Regd. & Corporate Office: Urja Sadan, Nana Varachha Road, Kapodara Char Rasta,Surat 395 006 C & R DEPARTMENT Phone No.: 0261 2506100-200-175
More information