USER MANUAL QFT-7. Folding Bicycle. RILU Trading Pty

Transcription

1 P a g e 1 USER MANUAL QFT-7 Folding Bicycle RILU Trading Pty Unit 2, No 2 Caulson Close Maribyrnong 3032 Melbourne, Victoria Australia (03) info@rilu-e-bike.com.au Rev QF7-UM

2 P a g e 2 Introduction Product Description Page 4 Riding Range & Load Weight Page 5 Product Summary Page 6 General Usage Summary Page 7 Display Turning your Q-F7T (ON/OFF) Page 8 PAS Default Motor Assistance Level Page 9 Front & Rear lights (ON/OFF) Page 9 PAS - Turn OFF Motor Assistance Page 10 PAS - Motor Assistance MAX Page 10 6km/h - Walk Assist Function Page 10 Understanding Battery Capacity Meter Page 11 Battery LOW Flashing Wanning Page 12 Folding Step by step guide to folding your bike Page 13 Servicing your folding lock Page 17 Gearing Gear Adjustment Uneven Shifting Page 19 Gear Alignment Gear #7 Page 20 Gear Alignment Gear #1 Page 21

3 P a g e 3 Motor Motor Changing Tire Page 22 Motor Service Notes Page 23 Battery Removing battery from inside frame Page 24 Charger Page 25 Battery Storage Page 25 Sensors Pedal Sensor Location Page 27 Pedal Sensor Repair Page 28 Thumb Throttle Page 29

4 P a g e 4 Product Description Frame: Gears: Brakes: Stem: Front Fork: Rim & Tire Seat Post: Saddle: 6061 Aluminium alloy Lightweight Folding Frame Altus 7 Shimano Front Disc and Rear V-Brake Height Adjustable Aluminium Alloy. High Strength Aluminium alloy 20 x 13G x 36H alloy Double wall with wide tires Quick Adjust Clamp VELO Plush Saddle Motor: 36V / 200 W (Thumb + PAS) Display: LED / 3 Modes (Motor Power L/M/H) Battery: 36 V / 10.4AH (Lithium Ion) Charger: 36V / 2A (Smart charger) Lights: Front & Rear (ebike battery power)

5 P a g e 5 Riding Range & Charge Time Range depending on: Rider, terrain, weather & level of assistance. Throttle PAS 30Km+ 50Km+ Battery charge time is 4-5 Hours Weight 17.8 Kg (Bike) net weight 19.5Kg (Battery Installed) QF7-T Rated Load weight is 120Kg

6 P a g e 6 Product Summary Congratulation on your purchase of a RILU Q-F7T Folding electric bicycle. Your new electric bicycle has two different ways of activating motor power. Throttle Located on the right hand side of the handlebar is a thumb triggered throttle which enables you to control the speed of the motor, without the need for pedalling. PAS Built into your Q-F7T is a Pedal Assistance Sensor. This automatically detect the speed at which you pedal and will automatically moderate the motors speed while riding. By selecting one of the three modes low/med/high on the LED display you are able to adjust the amount of motor output power that is automatically given when pedalling is detected by the PAS. Override Function Engaging the throttle will override your PAS setting

7 P a g e 7 General Usage Summary RILU recommends you first ride the bike without using any electrical assistance to familiarize yourself with the mechanical gearing and breaking system of your Q-F7T.

8 P a g e 8 Turning Q-F7T (ON & OFF) HOLD M TURN ON Can t power on your display? Check the battery power switch. Ensure its set to the ON position. You only need to turn off the battery when not using the Q-F7Tfor long period of time (longer than one month)

9 Default Motor Assistance Level P a g e 9 Turn ON Riding LED lights HOLD +

10 P a g e 10 MODE 0 (PAS turned OFF) Throttle will still function in MODE 0 Press - Set PAS Motor Assistance to MAX Only use high once you are confident with riding your Q-F7T. Press + 6Km/h Walk Assist Function Hold - Only use Walk Assist when you are walking the bike, do not use while sitting on the bike.

11 Understanding Battery Capacity Meter P a g e 11 The battery capacity gauge is located below the POWER logo at the bottom of the handlebar LED Display. It is an approximate estimation of battery capacity based on a real-time voltage reading of the battery pack. There are several factors that may affect the accuracy of the reading such as cold weather or steep inclines. When the motor is under heavy load the POWER gauge LEDs will sag showing an underestimated capacity reading. The gauge will correct itself after the heavy load is lifted.

12 P a g e 12 Battery Low Flashing Warning When battery LED is Flashing Battery charge level is <10%. It is critical that you recharge within 24 hours to avoid any damage to the battery.

13 P a g e 13 Folding Guide Step 1 - Lower seat post. This will enable the seat post to act as a balance leg assisting the bike to keep upright when folded LOWER SEAT MIN SEATPOST TO GROUND Step 2 - Fold pedals Reduces risk of damaged during transport and storage

14 P a g e 14 Step 3 - Align the pedals Chain side Pointing to the back of the bike. Step 4 - Unlock Folding Safety Latch TWIST UP Step 5 - Pull Folding Lever forward PULL Forward

15 P a g e 15 Step 6 - Fold handlebar stem Release (UP) (Stem lock) Fold (DOWN) (Stem latch) Step 7 - Stand behind the folding lock

16 P a g e 16 Step 8 - Fold the bike in half Step 9 - Carry using two hands Hand 1 - Rear of bike rack Hand 2 - Folded bike frame HAND 2 HAND 1

17 P a g e 17 Adjusting - Folding Clamp Over time you may need to adjust the folding clamp if you are unable to fully close the clamp before riding or if the folding lock is loose and doesn t grip the frame. TIGHTEN LOOSEN

18 Adjusting - Gear Quick Adjustment P a g e 18 RILU advises using a bike service stand when performing gearing and breaking adjustments. It will be easier when the bike is raised off the ground. Electric bicycles are heavier than regular bicycles please ensure your bike stands weight rating meets the 20Kg requirement of your Q-F7T TURN OFF electric system when working on gearing and breaking to avoid any unexpected motor power. TURN OFF electric system when working on QFT-7

19 P a g e 19 Gearing Adjustment - Uneven Shifting / Slipping If you experience uneven shifts or slippage in the lower gears, where the chain jumps from gear #2 to gear #3 unintentionally. Try to adjust the derailleur using the following method to improve shifting.

20 P a g e 20 Gearing Adjustment Gear #7 Pulley Alignment

21 P a g e 21 Gearing Adjustment Gear #1 Pulley Alignment

22 P a g e 22 Motor - Change Tire Step 1 Step 2 Cut - Cable Tie Unplug - Motor Cable Step 3 Step 4 5mm Allen - Release Brakes Check Brake Pad Free Step 5 Step 6 18mm Spanner Pull back derailleur Step 7 Step 8

23 P a g e 23 Motor Service Notes

24 P a g e 24 Battery Unlocking Battery Removal Pinch the battery Pull away from frame Battery Installation Battery Removal No Gap OK Flush with edge correctly installed Battery pushed too far inside. The lock is unable to fully turn. Not installed correctly

25 P a g e 25 Battery - Charger Warnings The charger will warm up during charging. Ensure charging takes place in a well-ventilated area. DO NOT cover the charger, nor the battery during charging. Battery Charging Error Battery (RED) & Charger (GREEN) Contact your dealer for support if you experience the above issue or if battery not receiving charge.

26 P a g e 26 Battery Charging Steps Battery Storage Guide

27 P a g e 27 Pedal Sensor Location & Function Wedged between the chain wheel and the bottom bracket is the Pedal Assist Sensor and the Rotation Disk. Pedalling will cause the Disk to rotate, the sensor is able to detect the rate (cadence) at which you are pedalling. Pedal Assist Sensor Rotation Disk

28 P a g e 28 Pedal Sensor No Motor Power If you are pedalling while in mode (low/med/high) and are not receiving automatic motor assistance or experiencing intermittent motor power please inspect the pedal assist sensor and the rotation disk alignment as it is possible to knock and bend the sensor when folding your ebike <5mm

29 Thumb Throttle Location & Function P a g e 29 RILU advises riders to avoid hard starts that involve applying full throttle while on an incline. RILU recommends to have the bike in motion before engaging the throttle to prolong the life of the gears inside the motor. PUSH DOWN Actives Throttle Thumb Throttle Loose If you find the throttle is free spinning there is a 4mm Allen screw located at the base of the throttle, tighten it to avoid any further movement. 4mm Allen