S25500 MAXI STIRRER OPERATION MANUAL AND PARTS LIST SERIES 1352

Transcription

1 S25500 MAXI STIRRER OPERATION MANUAL AND PARTS LIST SERIES 152 Model S1505 Series Volt 50/60 HZ Model S Series Volt 50/60 HZ Model S2555 Series Volt 50/60 HZ Model S2550- Series Volt 50/60 HZ LT152X1 7/7/04

2 Table of Contents IMPORTANT INFORMATION This manual contains important operating and safety information. You must carefully read and understand the contents of this manual prior to the use of this equipment. Safety Information... Alert Signals... Warnings... Declaration of Conformity...4 Environmental Conditions...4 Introduction...5 Electrical Ratings...5 Unpacking...5 Operation...6 Maintenance...7 Parts List...8 Exploded View...9 Wiring Diagram...10 Ordering Procedures...11 One Year Limited Warranty

3 Safety Information Alert Signals Warning Warnings alert you to a possibility of personal injury. Caution Cautions alert you to a possibility of damage to the equipment. Note Notes alert you to pertinent facts and conditions. Hot Surface Hot surfaces alert you to a possibility of personal injury if you come in contact with a surface during use or for a period of time after use. Your Barnstead Thermolyne Type S25500 Maxi Stirrer magnetic stirrer has been designed with function, reliability, and safety in mind. It is your responsibility to install it in conformance with local electrical codes. For safe operation, please pay attention to the alert signals throughout the manual. Warnings To avoid electrical shock, always: 1. Use a properly grounded electrical outlet of correct voltage and current handling capacity. 2. Disconnect from the power supply prior to maintenance and servicing. To avoid personal injury: 1. Do not use in the presence of flammable or combustible materials; fire or explosion may result. This device contains components which may ignite such materials. 2. Refer servicing to qualified personnel.

4 SAFETY INFORMATION Declaration of Conformity (For CE models only) Barnstead International hereby declares under its sole responsibility that this product conforms with the technical requirements of the following standards: EMC: EN Limits for harmonic current emissions EN Limits for voltage fluctuations and flicker EN Electrical equipment for measurement, control and laboratory use; Part I: General Requirements Safety: EN Safety Requirements for electrical equipment for measurement, control and laboratory use; Part I: General Requirements EN Part II: Particular requirements for laboratory equipment for mixing and stirring per the provisions of the Electromagnetic Compatibility Directive 89/6/EEC as amended by 92/1/EEC and 9/68/EEC, and per the provisions of the Low Voltage Directive 7/2/EEC, as amended by 9/68/EEC. The authorized representative located within the European Community is: Electrothermal Engineering, Ltd. 419 Sutton Road Southend On Sea Essex SS2 5PH United Kingdom Copies of the Declaration of Conformity are available upon request. Environmental Conditions Operating: 17 C to 27 C; 20% to 80% relative humidity, non-condensing. Installation category II (overvoltage) in accordance with IEC 664. Pollution Degree 2 in accordance with IEC 664. Altitude Limit: 2,000 meters. Storage: -25 C to 65 C 20% to 80% relative humidity 4

5 Introduction Intended Use The Type S25500 Maxi Stirrer is designed to provide maximum torque for stirring viscous solutions and up to 5 gallons of aqueous solution within a speed range of 60 to 1050 rpm. The powerful 7.5 drive magnet can accommodate from to 6 stir bars. General Usage Do not use this product for anything other than its intended usage. Electrical Ratings S Volt 1.4 Amps 160 Watts 50/60 Hz S Volt 1.2 Amps 185 Watts 50/60 Hz Unpacking Carefully unpack the unit. Be sure the bench or work area where the stirrer is placed will be able to support the weight of the stirrer plus the weight of the vessel and its contents. For example, the weight of the stirrer is 40 Ibs., the weight of a 0-gallon container may be about 15 Ibs., and 0 gallons of aqueous solution will weigh 250 Ibs. The total weight would therefore be greater than 00 Ibs. Alternatively, of course, the stirrer may be placed on the floor where it is more convenient in using the larger sizes of vessels. 5

6 Operation Note Unlike smaller magnetic stirrers, the motor of a large magnetic stirrer can be overloaded. This will cause the 1-1/2 ampere SLO BLO fuses to blow or the motor to overheat. Any stir-bar up to 6-1/4 long and 1-1/16 in diameter may safely be used with the Maxi Stirrer without danger of overloading the motor. Warning Disconnect from power supply before servicing. Refer servicing to qualified personnel. Place the vessel with its contents atop the stirrer. Any stirbar from 2 to 6 long may be used. To stir larger volumes or viscous solutions at higher speeds, it may be necessary to gradually increase the stirring speed control. Maximum stirring speeds attainable will be determined by the length and diameter of the stir-bar, the material of the vessel, the bottom configuration of the vessel (a slight crown in the center is desirable) and, of course, the volume and viscosity of the solution. The extremely strong pull of the stirring magnet on the stir-bar can cause friction between the stir bar and vessel bottom resulting in reduced stirring speed. The configuration and vessel material can drastically vary the amount of friction and corresponding speed reduction. The speed control rheostat is a combination ON OFF switch and setting selector. The fully counterclockwise position is OFF, fully clockwise is maximum speed. To select a speed, turn the speed control knob clockwise until the desired mixing action is achieved. A separate ON OFF rocker switch is provided in the event a desired setting is to be reused. The rheostat may be left at the setting and the stirrer turned off and on by means of the rocker switch. 6

7 Maintenance General Cleaning Instructions Wipe exterior surfaces with lightly dampened cloth containing mild soap solution. 7

8 Parts List Key Number Part Number Description 1 BC255X1 Bracket for Top Plate (2 required) 2 HN255X1A Handle (2 required) PT255X1A Top Plate, Stainless Steel with Studs 4 FT255X1 Feet, Support Rods (8 required) 5 FZX44 Fuse Holder 6 FZX14 Fuse, 1.5 Amp Slo-Blo (2 required) 7 MG849X1A Drive Magnet Assembly 8 MT150X1 Motor Assembly 9 CAX24 Capacitor 10 TNX7 Transformer, Complete with Nut and Washer 11 KBX8 Knob 12 SWX17 Switch, On-Off (120 V) 12 SWX18 Switch, On-Off (240 V, V) Not Shown TN150X1 Transformer, Step Down ( V models) Not Shown CRX72 Cord and Plug Set (120 V) Not Shown CRX70 Cord and Plug Set, - model ( V) Not Shown MGX7 Stir Bar, Teflon-coated, 4-1/4 long X 1-1/16 diameter 1 FAX7 Fan ( V models) 8

9 Exploded View WM150X2 WM849X2A BLU REF. A PLACE TWO LONGER SPACES TOWARDS FRONT See Ref. A WM150X1 D A E B (2) FSX17 CAX24 DETAIL B DETAIL A WM1294X2 X22 DL150X2 2 ) FNX117 TOP H FROM MOTOR FZX44 J (2) FZX B E FROM SWITCH (2) 1 CEX172 A DLX80 1/2 REF. FROM TOP EDGE AND FRONT EDGE. DETAIL B F BRN C GRN/YLW WM61X7A (4) FNX8 (2) FNX66 (2) DL550X2 (1 EACH SIDE FWX11 TNX7 POSITION LOCKING PIN IN HOLE. DISCARD KNOB AND DIAL PLATE. FSX75 CS152X1 FSX128 W/ADX7 BC849X1 F BRN MG849X1A MOUNT MAGNET 1/2" FROM MOTOR HUB USING SPACER PROVIDED. G H MT150X1 WM1294X6 (TO #1) G (TO #) BLU (TO #2) 2 (4) FN255X1 PT152X1 DLX285 KBX8 (2) FSX54 (8) FSX168 Ref. A (4) FSX47 SUPPLI WITH TRANSFORM SWX17 SEE DETAIL A (8) FT255X1 DO NOT OVERTIGHTEN FEET TO STUDS OF TOP PLATE. OVERTIGHTENING WILL DEFORM TOP PLATE. CV849 (4) FSX224 (2) BC255X1 (4) FTX22 (4) FWX7 (4) FSX19 (4) FWX12 (2) FW205X2 (4) FSX5 NOTE: FRONT ASSEMBLE SO THE SANDING LINES GO FROM LEFT TO RIGHT WHEN VIEWED FROM THE FRONT OF THE UNIT. (2) HN255X1A (MUST BE CENTERED) PT255X1A 9

10 Wiring Diagram LINE CAPACITOR GRN (GRN/YEL) GND BRN GND MOTOR (GRAY) (GRAY) GRN V MODEL TRANS FORMER FAN BLU 1 (GRAY) (GRAY) 2 SPEED CONTROL SWITCH S1 T1 2:1 T2 F1 F2 2 M1 LINE GND C1 GND V MODEL CIRCUIT DIAGRAM DIAGRAM COMPONENT LIST REF. NO. DESCRIPTION S1500- S2550- S S C1 CAPACITOR CAX24 CAX24 F1 FUSE FZX14 FZX14 M1 MOTOR MT150X1 MT150X1 S1 SWITCH SWX18 SWX17 T1 TRANSFORMER TN150X (STEP DOWN) T2 TRANSFORMER TNX7 TNX7 (VARIABLE) F2 FAN FAX

11 Ordering Procedures Please refer to the Specification Plate for the complete model number, serial number, and series number when requesting service, replacement parts or in any correspondence concerning this unit. All parts listed herein may be ordered from the Barnstead International dealer from whom you purchased this unit or can be obtained promptly from the factory. When service or replacement parts are needed we ask that you check first with your dealer. If the dealer cannot handle your request, then contact our Customer Service Department at or Prior to returning any materials to Barnstead International, please contact our Customer Service Department for a Return Materials Authorization number (RMA). Material Returned without an RMA number will be returned. 11

12 One Year Limited Warranty BARNSTEAD INTERNATIONAL ( BARNSTEAD ) warrants that if a product manufactured by Barnstead shall be free of defects in materials and workmanship for one (1) year from the first to occur of (i) the date the product is sold by BARNSTEAD or (ii) the date the product is purchased by the original retail customer (the Commencement Date ). Except as expressly stated above, BARNSTEAD MAKES NO OTHER WARRANTY, EXPRESSED OR IMPLIED, WITH RESPECT TO THE PRODUCTS AND EXPRESSLY DISCLAIMS ANY AND ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF DESIGN, MERCHANT ABILITY AND FITNESS FOR A PARTICULAR PURPOSE. An authorized representative of BARNSTEAD must perform all warranty inspections. In the event of a defect covered by BARNSTEAD s warranty, BARNSTEAD shall, as its sole obligation and exclusive remedy, provide free replacement parts to remedy the defective product. In addition, for products sold by BARNSTEAD within the continental United States or Canada, BARNSTEAD shall provide provide free labor to repair the products with the replacement parts, but only for a period of ninety (90) days from the Commencement Date. BARNSTEAD s warranty provided hereunder shall be null and void and without further force or effect if there is any (i) repair made to the product by a party other than BARNSTEAD or its duly authorized service representative, (ii) misuse (including use inconsistent with written operating instructions for the product), mishandling, contamination, overheating, modification or alteration of the product by any customer or third party or (iii) use of replacement parts that are obtained from a party who is not an authorized dealer of BARNSTEAD. Heating elements, because of their susceptibility to overheating and contamination, must be returned to the BARNSTEAD factory and if, upon inspection, it is concluded that failure is due to factors other than excessive high temperature or contamination, BARNSTEAD will provide warranty replacement. As a condition to the return of any product, or any constituent part thereof, to BARNSTEAD s factory, it shall be sent prepaid and a prior written authorization from BARNSTEAD assigning a Return Materials Number to the product or part shall be obtained. IN NO EVENT SHALL BARNSTEAD BE LIABLE TO ANY PARTY FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OR FOR ANY DAMAGES RESULTING FROM LOSS OF USE OR PROFITS, ANTICIPATED OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THE SALE, USE OR PERFORMANCE OF ANY PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CON- TRACT, TORT (INCLUDING NEGLIGENCE), ANY THEORY OF STRICT LIABILITY OR REGULATORY ACTION. The name of the authorized Barnstead International dealer nearest you may be obtained by calling ( ) or writing to: 2555 Kerper Boulevard P.O. Box 797 Dubuque, Iowa Phone: or Fax: mkt@barnstead.com