Inverter/Chargers. Off-Grid Inverters. Solar charge controllers

Transcription

1

2 Inverter/Chargers If you have a solar power system then a Inverter or chargers can assist you by optimising the energy your system generates. If your solar power system generates more energy than your business or household requires, the surplus or excess energy can be fed back into the utility grid or used for additional loads through the use of Inverter or chargers. Inverter or chargers ensure that you maximise the energy produced by your solar system. They also allow you to access energy from your utility grid when your stored solar energy is insufficient. Off-Grid Inverters If you are looking to take your home or business completely off-grid and become independent from your unreliable electricity supplier then you will require an off grid inverter. This device is used in conjunction with other components to store energy that is generated from solar, wind or hydropowered systems. This device ensures that you have access to stored surplus power when energy production is insufficient. Victron Energy s range of off grid inverters offers you a multi-functional power solution. Our inverters offer optimised efficiency without compromising on performance. We supply an extensive range of off grid inverters with multiple volt and amp options to ensure you are equipped with the device that is best suited to your system requirements. Solar charge controllers Victron Energy s range of solar regulators offers intelligent battery management and protection. Our range of 8 BlueSolar MPPT charge controllers can improve energy harvest by up to 30% on cloudy days as well as monitoring the state of charge and load output. Our PWM solar regulators or charge controllers protect against over load and short circuit as well as providing protection against reverse polarity connection of the solar array and/or battery. Victron Energy offer solar regulators to suit your specific requirements and budget. The PWM charge controllers are a good low cost solution for small solar power systems while the MPPT controllers are better suited to higher power systems.volt and amp options to ensure you are equipped with the device that is best suited to your system requirements.

3 Battery Chargers Victron Energy offers an extensive range of chargers that can accommodate a wide variety of battery types. These technologically advanced chargers are built to withstand tough environmental conditions such as heat, humidity and salt air. The Victron Energy chargers include built-in battery controllers and fully monitored battery capacity to ensure optimal performance. Some of the devices in our Blue Power range are completely encapsulated; making them waterproof, shockproof and ignition protected. When compared to the industry standard, Victron Energy battery chargers outperform on every level. Battery Protectors Battery protectors are responsible for disconnecting your loads before the battery is flat. This prevents unnecessary damage to your battery. Other beneficial features include auto ranging which automatically detects system voltage, over voltage protection which prevents damage to sensitive loads and delayed alarm output and delayed load disconnect. To ensure the quality and longevity of your battery, equip it with a Victron Energy battery protector. We have a selection of products to choose from in order to accommodate your specific requirements. Victron Energy has 3 battery protectors to choose from, ranging from 40A-200A. System Monitoring Victron Energy offers an extensive range of system monitoring products. These innovative devices provide functional value by monitoring and displaying the output of your inverters, batteries and chargers. Within our range of system monitoring devices we have Digital Multi Control Panels, Remote Control Panels and Charge Controllers. These devices allow you to alter the charge current, monitor the system status and view the charge on your battery system. System monitoring products provide you data relating to your power system.

4 Inverter/Chargers If you have a solar power system then a Inverter or chargers can assist you by optimising the energy your system generates. If your solar power system generates more energy than your business or household requires, the surplus or excess energy can be fed back into the utility grid or used for additional loads through the use of Inverter or chargers. Inverter or chargers ensure that you maximise the energy produced by your solar system. They also allow you to access energy from your utility grid when your stored solar energy is insufficient. Multi Compact Proven reliability High start-up power 12V / 24V The main output has no break functionality. The MultiPlus takes over the supply to the connected loads in the event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption. Prices Excluding VAT Price MultiPlus C 12/800/35-16 MultiPlus C 12/1200/50-16 MultiPlus C 12/1600/70-16 MultiPlus C 12/2000/80-30 MultiPlus C 24/800/16-16 MultiPlus C 24/1200/25-16 MultiPlus C 24/1600/40-16 MultiPlus C 24/2000/50-30 PowerControl Transfer switch Input voltage range R R R R R R R R Yes 16A 9,5 17V 19 33V 38 66V Output Output voltage: 230VAC ± 2% MultiPlus C 12/800/35-16 MultiPlus C 12/1200/50-16 MultiPlus C 12/1600/70-16 MultiPlus C 12/2000/80-30 MultiPlus C 24/800/16-16 MultiPlus C 24/1200/25-16 MultiPlus C 24/1600/40-16 MultiPlus C 24/2000/ V / 800VA 12V / 1200VA 12V / 1600VA 12V / 2000VA 24V / 800VA 24V / 1200VA 24V / 1600VA 24V / 2000VA Multi+C12/800/35-16 Multi+C12/1200/50-16 Multi+C12/1600/70-16 Multi+C12/2000/80-30 Multi+C24/800/16-16 Multi+C24/1200/25-16 Multi+C24/1600/40-16 Multi+C24/2000/ W 2400W 3000W 4000W 1600W 2400W 3000W 4000W MultiPlus 12V 9,5-17V Input range(v DC), VA Continous output power at 25 C, Peak power(w) The MultiPlus is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kva Multi at 230 VAC). Prices Excluding VAT MultiPlus 12/500/20-16 MultiPlus 12/800/35-16 MultiPlus 12/1200/50-16 PowerControl Transfer switch Input voltage range Peak power (W) 900W R W R W R A no Multi 12/500/20-16 Multi 12/800/35-16 Multi 12/1200/ ,5 17 V / V / V Output Output voltage: 230VAC ± 2% AC Input Charge current starter battery Battery temperature sensor MultiPlus 12/3000/ MultiPlus 12/3000/ Peak power (W) Charger VAC 1A (12V and 24V models only) yes 6000W R W R Multi+12/3000/ Multi+12/3000/ PowerControl Transfer switch yes 50A visit website for full spec and download on the MultiPlus range Input voltage range 9,5 17 V / V / V Output Output voltage: 120VAC ± 2% Charger AC Input Input voltage range: VAC Charge current starter battery 120/70 Battery temperature sensor yes

5 MultiPlus 24V 19 33V Input range(v DC), VA Continous output power at 25 C, Peak power(w) The MultiPlus is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kva Multi at 230 VAC). With the Multi Control Panel, a maximum generator or shore current can be set. Prices Excluding VAT Multi 24/500/10-16 Multi 24/800/16-16 PowerControl Transfer switch Input voltage range Peak power (W) 900W R W R6 026 No 16A 9,5 17 V V V Multi24/500/10-16 Multi 24/800/16-16 Output Output voltage: 230VAC ± 2% AC Input Charge current starter battery (A) Battery temperature sensor Prices Excluding VAT Peak power (W) Multi 24/1200/25-16 Multi 24/3000/70-16 Multi 24/3000/70-50 Multi 24/5000/ V MultiPlus24/3000/ Charger VAC 1A (12 V and 24 V models only) 2400W R W R W R W R W R yes Multi 24/1200/25-16 Multi+24/3000/70-16 Multi+24/3000/70-50 Multi+24/5000/120 Multi+24/3000/120V MultiPlus 48V 38 66V Input range(v DC), VA Continous output power at 25 C, Peak power(w) The MultiPlus is a very powerful battery charger. It will, therefore, draw a lot of current from the generator or shore side supply (nearly 10 A per 5 kva Multi at 230 VAC). With the Multi Control Panel, a maximum generator or shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for charging, thus preventing the generator or shore supply from being overloaded. Prices Excluding VAT Multi 48/500/20-16 PowerControl Transfer switch Input voltage range Peak power (W) 6000W Price on No 16A 9,5 17 V V V Multi 48/500/20-16 Output Output voltage: 230VAC ± 2% AC Input Charge current starter battery (A) Battery temperature sensor Prices Excluding VAT Peak power (W) Charger VAC 1 (12 V and 24 V models only) yes PowerControl yes Transfer switch 50A Input voltage range 9,5 17 V V Output Output voltage: 120 VAC ± 2% Multi 48/800/8-16 Multi 48/1200/13-16 MultiPlus 48/3000/35-16 Multi 48/3000/35-50 Multi 48/5000/ W Price on 2400W Price on 6000W Price on 6000W R W R Multi 48/800/9-16 Multi 48/1200/13-16 Multi+48/3000/35-16 Multi+48/3000/35-50 Multi+48/5000/ AC Input Charge current starter battery (A) Battery temperature sensor Charger Input voltage range: VAC 4 (12 V and 24 V models only) yes PowerControl Transfer switch Input voltage range yes 16A 9,5 17 V V V Output Output voltage: 230VAC ± 2% Interface MK3-USB (VE.Bus to USB) Connects to a USB port: R : MK3-USB AC Input Charge current starter battery (A) Battery temperature sensor Charger VAC 4 (12 V and 24 V models only) yes

6 visit website for full spec and download on the Quattro inverters EasyPlus C12/1600/70-16 Number of AC outputs: 4 Number of AC inputs: 1 Continuous output power at 25 C (VA): 1600VA (VDC): 12VDC Excluding VAT: R Order code: Easy+C12/1600/70-16 The EasyPlus guarantees uninterrupted power supply, whenever and wherever you are. Where shore or generator power is limited, the unique PowerAssist technology makes it possible to boost the total capacity by adding extra energy from the batteries. Optimum safety is guaranteed with the integrated RCD (Residual Current Device) protecting against earth leakage. * 12 Volt 1600VA sine wave inverter (3000 Watt peak power) * 70A charger incl. 4A trickle charge for start battery * Unique PowerAssist technology protects the shore or generator from being overloaded by adding extra inverter power when needed * 4 stage adaptive charge technology for quick and accurate battery charging * The AC distribution consists of a RCD (30mA/16A) and four AC outputs protected by two 10A and two 16A circuit breakers * One 16A output is controlled by the AC input: it will switch on only when AC is available. * RCD (30mA/16A) on AC output * No-break system: uninterrupted switching between shore/generator and inverter * Battery cables included Quattro 3-15kVA 12/24/48V PowerControl / PowerAssist The Quattro is a very powerful battery charger. It will therefore draw a lot of current from the generator or shore side supply (16A per 5kVA Quattro at 230VAC). * Ultra-fast Maximum Power Point Tracking (MPPT) * Load output Prices Excluding VAT Peak power (W) Quattro 12/3000/120-50/50 Quattro 12/5000/ /100 Quattro 24/3000/70-50/50 Quattro 24/5000/ /100 Quattro 24/8000/ /100 Quattro 48/5000/70-100/100 Quattro 48/5000/70-100/100-S Quattro 48/8000/ /100 Quattro 48/10000/ /100 Quattro 48/15000/ /100 PowerControl Transfer switch Input voltage range 6000W R W R W R W R W R W R W R W R W R W R yes yes QUATTRO 12/3000/120 QUATTRO 12/5000/220 QUATTRO 24/3000/70 QUATTRO 24/5000/120 QUATTRO 24/8000/200 QUATTRO 48/5000/70 QUATTRO 48/8000/110 QUATTRO 48/10000/140 QUATTRO48/15000/200 Input voltage range: VAC Output Output voltage: 230 VAC ± 2% Charge current starter battery Battery temperature sensor VE.Bus communication port Charger 4 (12V and 24V models only) yes For parallel and three phase operation, remote monitoring and system integration MultiPlus-II 48/3000/ V The Victron Energy MultiPlus-II inverter/charger combines the functions of the MultiPlus and the MultiGrid. It has all the features of the MultiPlus, plus an external current transformer option which extends the PowerControl and PowerAssist function to 100A. visit website for full spec and download on the EasyPlus inverters Current transformer 100A:50mA for MultiGrid II R : CurrentTransformer visit website for full spec and download on the MultiPlus II inverters Peak power (W) Price excluding VAT Pastel code MultiGrid II 48/3000/ V/5500W R MultiGrid II 48/3000 MultiPlus II 48/3000/ W R Transfer switch AC Input Battery temperature sensor 32A Charger Input voltage range: VAC VE.Bus Smart dongle (6) (optional)

7 EasySolar 12/24/48V All-in-one solar power solution The MPPT charge controller and the MultiPlus Compact inverter/ charger share the DC battery cables (included). The batteries can be charged with solar power (BlueSolar MPPT) and/or with AC power (inverter/charger) from the utility grid or a genset. visit website for full spec and download on the EasySolar Prices Excluding VAT ECOmulti R Excluding VAT Order code: ECO-MUL24/3000/70-50 ECO-MUL24/3000/70-50 A simple wall mounted energy storage solution Nighttime During the night the ECOmulti is disconnected from the grid. The home is powered by energy stored in the battery. The ECOmulti will reconnect to the grid when the battery is discharged. Battery charging The next day, when the PV array produces sufficient power to supply the loads and to start charging the battery, the ECOmulti will regulate charge current to absorb nearly 100% of the surplus PV power. Discharging during the day When PV output is reduced by clouds or when a power hungry load is switched on, resulting in no surplus PV power available, battery charging will stop. Insufficient PV power will be supplemented by power from the ECOmulti. In case of overload power will be imported from the grid to supplement power from the ECOmulti (GridAssist function), and system shut down due to overload will be prevented. Battery fully charged Once the battery is fully charged, additional loads (for example the water heater) can be switched on, or surplus power will be exported to the grid. End of the day The ECOmulti disconnects from the grid about 10 minutes after PV power has become insufficient to provide any charge current. In order to prevent false disconnections due to lack of sun during the day, the inverter/ charger also uses an internal timer to predict the end of the day. UPS function When the grid fails, the ECOmulti will continue to power the home. GridAssist function BIDERECTIONAL CONVERTER Maximum AC current feed-through Technology Nominal voltage Battery Management System visit website for full spec and download on the Ecomulti In case of overload the ECOmulti will import power from the grid to prevent system shutdow BATTERY 50 A Lithium Iron Phosphate 25,6 V Cell balancing, and system shutdown in case of cell over voltage, cell under voltage and over temperature EasySolar 12/1600/70 EasySolar 24/1600/40 Transfer switch AC Input Battery temperature sensor Maximum output current Maximum output current EasySolar 24/3000/70 EasySolar 48/3000/35-50 EasySolar 48/3000/35 Transfer switch AC Input Battery temperature sensor Maximum output current Maximum output current Peak power (W) Peak power (W) Peak power (W) 12V/1600W R V/1600W R Charger EasySolar 12/1600/70 EasySolar 24/1600/40 16A Input voltage range: VAC Input frequency: Hz Power factor: 1 Solar Charge Controller 24V/6000W R V/6000W R V/6000W R Charger Solar Charge Controller yes 50A 700W / 1400W 50A EasySolar 24/3000/70 EasySolar 48/3000/35 Output voltage: 230VAC ± 2% Frequency: 50 Hz ± 0,1% (1) yes 70A 2000W / 4000W EasySolar 48/5000/70 48V/10000W R EasySolar 48/5000/70 Transfer switch AC Input Battery temperature sensor Maximum output current Maximum output current MultiGrid 24/3000/70-50 MultiGrid 48/3000/35-50 Transfer switch AC Input Battery temperature sensor MultiGrid Peak power (W) Charger Solar Charge Controller 24V/6000W R V/6000W R Charger 100A Output voltage: 230VAC ± 2% Frequency: 50 Hz ± 0,1% (1) yes 100A 5800W The flexible energy storage and self-consumption solution There is no one-size-fits-all solution to energy storage. The building blocks, topology and control systems will depend on local conditions and regulations. The MultiGrid hardware, together with a wide range of software tools, seamlessly fits in all common topologies Prices Excluding VAT MultiGrid 24/3000/70 MultiGrid48/ A Input voltage range: VAC yes visit website for full spec and download on the MultiGrid

8 Off-Grid Inverters If you are looking to take your home or business completely off-grid and become independent from your unreliable electricity supplier then you will require an off grid inverter. This device is used in conjunction with other components to store energy that is generated from solar, wind or hydropowered systems. This device ensures that you have access to stored surplus power when energy production is insufficient. Victron Energy s range of off grid inverters offers you a multi-functional power solution. Our inverters offer optimised efficiency without compromising on performance. We supply an extensive range of off grid inverters with multiple volt and amp options to ensure you are equipped with the device that is best suited to your system requirements. Phoenix Inverter 3000VA 12 / 24 / 48 Volt. Pure sine wave output, high peak power and high efficiency. Combined high frequency and line frequency technologies ensure the best of both worlds. Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimised efficiency but without compromise in performance. Phoenix Inverter 5000VA 12 / 24 Volt. Pure sine wave output, high peak power and high efficiency. Combined high frequency and line frequency technologies ensure the best of both worlds. Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimised efficiency but without compromise in performance. Phoenix Inverter Compact 1200VA VA 12 / 24 Volt. The Phoenix Inverter Compact is a pure sine wave inverter with a high efficiency. It is developed for professional duty and suitable for the wides range of applications. The Phoenix Inverters Compact is available from 1200VA up to 2000VA in 12V or 24V. Prices Excluding VAT Prices Excluding VAT Prices Excluding VAT Peak power (W) 12/3000 R /3000 R /3000 R Parallel and 3-phase operation Input voltage range (V DC) Output Programmable relay Remote on-of 12V/3000W 24V/3000W 48V/3000W Order Code PhoenixInver 12/3000 PhoenixInver 24/3000 PhoenixInver 48/3000 yes Input voltage range (V DC) 9,5 17V 19 33V 38 66V Output voltage: 230 VAC ±2% Frequency: 50 Hz ± 0,1% (1) GENERAL Yes yes Safety EN Peak power (W) 24/5000 R /5000 R Parallel,3-phase and split-phase operation 12V/3000W 24V/3000W Inverter Order Code PhoenixInver 24/5000 PhoenixInver 48/5000 yes Peak power (W) 6000 Output Zero load power (W) Remote on-off Output voltage: 120 VAC ±2% Frequency: 60 Hz ± 0,1% (1) 20 yes C12/1200 R C12/1600 R C12/2000 R C24/1200 R C24/1600 R C24/2000 R Peak power (W) Input voltage range (V DC) Output Safety 12V/1200W 12V/1600W 12V/2000W 24V/1200W 24V/1600W 24V/2000W INVERTER Order Code PhoenixInverC12/1200 PhoenixInverC12/1600 PhoenixInverC12/2000 PhoenixInverC24/1200 PhoenixInverC24/1600 PhoenixInverC24/2000 9,5 17V 19 33V 38 66V yes Output voltage: 230 VAC ±2% Frequency: 50 Hz ± 0,1% (1)

9 Phoenix Inverter 180VA- 12/24V 12 / 24 Volt. Phoenix Inverter 350VA- 12/24/48V 12 / 24 / 48 Volt. Phoenix Inverter 800VA- 12/24/48V 12 / 24 / 48 Volt. Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact dimensions, light in weight and capable of supplying power, problem free, to any load. Prices Excluding VAT Peak power (W) 12/180 R /180 R1 015 Cont. AC power at 25 C (VA) Output AC voltage / frequency Protection category Remote on-off switch Automatic transfer switch 12V/350W 24V/350W Order Number Phoenix12/180 Schuko Phoenix24/180Schuko 175 / VAC or 230 VAC +/- 3% 50 Hz or 60 Hz +/- 0,1% ENCLOSURE IP 20 Two pole connector Filax ACCESSORIES BMV-700 Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact dimensions, light in weight and capable of supplying power, problem free, to any load. Prices Excluding VAT Peak power (W) 12/350 Price on 24/350 Price on 48/350 Price on Cont. AC power at 25 C (VA) Output AC voltage / frequency Protection category Remote on-off switch Automatic transfer switch 12V/700W 24V/700W 48/700W Order Number Phoenix12/350Schuko Phoenix24/350Schuko Phoenix48/350Schuko 300 / VAC or 230 VAC +/- 3% 50 Hz or 60 Hz +/- 0,1% ENCLOSURE Prices Excluding VAT order number: BMV-700 BMV-700 Battery Monitor R1 641 The BMV-700 Battery Monitor features an advanced microprocessor control system combined with high resolution measuring systems for battery voltage and charge/ discharge current. Besides this, the software includes complex calculation algorithms to exactly determine the state of charge of the battery. IP 20 Two pole connector Filax Developed for professional duty, the Phoenix range of inverters is suitable for the widest range of applications. The design criteria have been to produce a true sine wave inverter with optimized efficiency but without compromise in performance. Employing hybrid HF technology, the result is a top quality product with compact dimensions, light in weight and capable of supplying power, problem free, to any load. Peak power (W) 12/800 R /800 Price on 48/800 Price on Cont. AC power at 25 C (VA) Output AC voltage / frequency Protection category Remote on-off switch Automatic transfer switch 12V/1600W 24V/1600W 48/1600W Order Number Phoenix12/800 Schuko Phoenix24/800Sch SEA Phoenix48/800 Schuko 700 / VAC or 230 VAC +/- 3% 50 Hz or 60 Hz +/- 0,1% ENCLOSURE IP 20 Two pole connector Filax Phoenix Inverter 1200VA-12/24/48V Prices Excluding VAT 12/1200 R /1200 R /1200 R4 947 Cont. AC power at 25 C (VA) Prices Excluding VAT Peak power (W) 12V/24000W 24V/24000W 48/240000W Order Number Phoenix12/1200Sch Phoenix24/1200Schuko Phoenix48/1200Sch 1000 / 900 Battery Alarm Battery Alarm An excessively high or low battery voltage is indicated by an audible and visual alarm, and a relay for remote signalling. order number: Battery Alarm GX R Output AC voltage / frequency 110 VAC or 230 VAC +/- 3% 50 Hz or 60 Hz +/- 0,1% ENCLOSURE Protection category IP 20 Remote on-off switch Automatic transfer switch Two pole connector Filax visit website for full spec and download on the Phoenix range

10 Phoenix Inverter VE.Direct Intelligent alarms, shut-downs, and re-starts A high power draw on start-up can trigger false alarms, and shutdowns. Phoenix makes allowance for this and only shuts down in cases of persistent overload. Intelligently - shut downs will be followed by a series of re-starts - to eliminate false alarms. Highly Reliable - built for the years ahead Phoenix Inverters are built to last. They feature sophisticated full-bridge and toroidal transformer topology - which is suitable for powering sensitive electronics. They are overload, temperature, and shortcircuit protected. Full bursts - High Peak output Some electronic devices - particularly those which have an electric motor - require short burst of energy on start-up which is much higher than their rated power consumption. No problem - the Phoenix inverter has industry-leading peak-power capability. 250VA Peak power (W) 12/250 R excl.VAT 24/250 R excl.VAT 48/250 R excl.vat Cont. AC power at 25 C (VA) Cont. power at 25 C 500VA Peak power (W) 12/500 R excl.VAT 24/500 R excl.VAT 48/500 R excl.vat Cont. AC power at 25 C (VA) Cont. power at 25 C 3000VA Order Code: 12V: Phoenix12/250 Schuko 24V: Phoenix24/250 Schuko 48V: Phoenix48/250 Schuko 12V/400W 24V/400W 48V/400W 200 / 175W 250VA Order Code: 12V: Phoenix12/500 Schuko 24V: Phoenix24/500 Schuko 48V: Phoenix48/500 Schuko Peak power (W) 12/3000 R excl.vat 24/3000 R excl.vat Cont. AC power at 25 C (VA) Cont. power at 25 C Order Code: 12V: 24V: 12V/900W 24V/900W 48V/900W 400 / 350W 500VA 12V/3000W 24V/3000W 2400W 3000VA 375VA Peak power (W) 12/375 R excl.vat 24/375 R excl.vat 48/375 R excl.vat Cont. AC power at 25 C (VA) Cont. power at 25 C 800VA Peak power (W) 12/800 R3 148 excl.vat 24/800 R3148 excl.vat 48/800 VE.Direct Schuko R excl.vat Cont. AC power at 25 C (VA) Cont. power at 25 C 1200VA Peak power (W) 12/1200 R excl.vat 24/1200 R excl.vat 48/1200 R excl.vat Cont. AC power at 25 C (VA) Cont. power at 25 C Order Code: 12V: Phoenix12/375Schuko 24V: Phoenix24/375 Schuko 48V: Phoenix48/375 Schuko 12V/700W 24V/700W 48V/700W 300 / 260W 375VA Order Code: 12V: Phoenix12/800 Schuko 24V: Phoenix24/800 Schuko 48V: 12V/1500W 24V/1500W 48V/1500W 650 / 560W 800VA Order Code: 12V: Phoenix12/1200Sch 24V: Phoenix24/1200Schuko 48V: 12V/2000W 24V/2000W 48V/2000W 1000 / 850W 1200VA VictronConnect VictronConnect lets you get live status info and configure Victron products with built-in bluetooth support or using VE.Direct Bluetooth Smart dongle visit website for full spec and download on the Phoenix VE.Direct range

11 Solar charge controllers Victron Energy s range of solar regulators offers intelligent battery management and protection. Our range of 8 BlueSolar MPPT charge controllers can improve energy harvest by up to 30% on cloudy days as well as monitoring the state of charge and load output. Our PWM solar regulators or charge controllers protect against over load and short circuit as well as providing protection against reverse polarity connection of the solar array and/ or battery. Victron Energy offer solar regulators to suit your specific requirements and budget. The PWM charge controllers are a good low cost solution for small solar power systems while the MPPT controllers are better suited to higher power systems.volt and amp options to ensure you are equipped with the device that is best suited to your system requirements. BlueSolar MPPT 75/10, 75/15 & 100/15 Solar charge controller. A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life. BlueSolar Controller MPPT 75/10 MPPT 75/15 MPPT 100/15 Rated charge current 10A 15A 15A BlueSol MPPT75/10 BlueSol MPPT75/15 BlueSol MPPT100/15 R911 R1012 R1237 Nominal PV power, 12V 145W 220W 220W Nominal PV power, 24V 290W 440W 440W Max. PV short circuit current 12A 20A 20A Maximum PV open circuit voltage Protection category 75V ENCLOSURE 100V IP43 (electronic components), IP22 (connection area) Remote Monitoring and Control Remotely control and monitor the extensive features of your BlueSolar MPPT charger by attaching a bluetooth dongle and pairing it with your smartphone or other device via VictronConnect. If your installation is connected to the internet Victron Remote Management Portal (VRM) provides access to the full power of your MPPT, anytime, anywhere; both services are free to use. For remote installations - even when there is no internet connection or phone signal nearby - you may be able to monitor your MPPT by bluetooth-pairing with a LoRaWAN (long-range wide area network) device, available optionally. Load output The intelligent Load output function prevents damage caused by running batteries flat. You can configure the voltage at which BlueSolar disconnects a load - thereby preventing excessive drain on your batteries. And here s the clever bit: BlueSolar will attempt a 100% recharge every day. If it can t - during periods of poor weather - it raises the disconnect voltage, daily, until it achieves success. We call this feature BatteryLife because it maintains the health, and extends the life of your battery. MPPT: Ultra Fast Maximum Power Point Tracking By constantly monitoring the voltage and current output of your solar (PV) panels, MPPT technology ensures that every drop of available power is rinsed out of your panels, and harvested for storage. The advantage of this is most noticeable when the sky is partially clouded, and light intensity is constantly changing.

12 BlueSolar MPPT 100/30 & 100/50 A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life. BlueSolar Controller MPPT 100/30 MPPT 100/50 12/24V Auto Select BlueSol MPPT100/30 BlueSol MPPT100/50 Prices excluding VAT R2 248 R3 373 Rated charge current 30A 50A Nominal PV power, 12V 440W 700W Nominal PV power, 24V 880W 1400W Protection category ENCLOSURE IP43 (electronic components), IP22 (connection area) BlueSolar MPPT 150/35 A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life. BlueSolar Controller MPPT 150/35 Rated charge current Nominal PV power, 12V Nominal PV power, 24V Nominal PV power, 48V 12 / 24 / 48V Auto Select (software tool needed to select 36V) 12/24/48V Auto Select 45A 650W 1300W 2600W BlueSol MPPT150/35 Prices excluding VAT R BlueSolar MPPT 150/45 & 150/60 - Tr Real-time data Display Options Apple and Android smartphones, tablets and other devices: see the VE.Direct to Bluetooth Smart dongle ColorControl panel BlueSolar Controller MPPT 150/45TR MPPT 150/60TR 12/24/48V Auto Select Rated charge current 45A 60A Nominal PV power, 12V 650W 860W Nominal PV power, 24V 1300W 1720W Nominal PV power, 48V 2600W 3440W BlueSol MPPT150/45TR BlueSol MPPT150/60TR Prices excluding VAT R5059 R5622 Screw terminal BlueSolar MPPT 150/70 & 150/85 Tr Real-time data Display Options Apple and Android smartphones, tablets and other devices: see the VE.Direct to Bluetooth Smart dongle ColorControl panel BlueSolar Controller MPPT 150/70 MPPT 150/85 BlueSol MPPT150/ 70TR Prices excluding VAT R /24V Auto Select BlueSol MPPT150/ 85TR Price on Rated charge current 50A 70A Nominal PV power, 12V 1000W 1200W Nominal PV power, 24V 2000W 2400W Nominal PV power, 48V 4000W 4900W Protection category ENCLOSURE IP43 (electronic components), IP22 (connection area) BlueSolar MPPT 150/100 Tr & 150/100MC4 BlueSolar Controller Prices excluding VAT Rated charge current MC4 Connection Nominal PV power, 12V Nominal PV power, 24V MPPT 150/100-Tr MPPT 150/100-MC4 12/24V Auto Select BlueSol MPPT150/100TR BlueSolMPPT150/100MC TR - Price on MC4 - Price on 50A 1000W 2000W BlueSolar MPPT 150/45 & 150/60 MC4 Real-time data Display Options Apple and Android smartphones, tablets and other devices: see the VE.Direct to Bluetooth Smart dongle ColorControl panel BlueSolar Controller MPPT 150/45MC4 MPPT 150/60MC4 12/24/48V Auto Select Rated charge current 45A 60A Nominal PV power, 12V 650W 860W Nominal PV power, 24V 1300W 1720W Nominal PV power, 48V 2600W 3440W Prices excluding VAT R5429 R5622 BlueSol MPPT150/70 R7 308 BlueSol MPPT150/85 R Nominal PV power, 48V 4000W

13 BlueSolar MPPT 150/70 & 150/85 MC4 Real-time data Display Options Apple and Android smartphones, tablets and other devices: see the VE.Direct to Bluetooth Smart dongle ColorControl panel BlueSolar Controller MPPT 150/70 MPPT 150/85 Prices excluding VAT R /24V Auto Select BlueSol MPPT150/ 85MC4 Price on Rated charge current 50A 70A Nominal PV power, 12V 1000W 1200W Nominal PV power, 24V 2000W 2400W Nominal PV power, 48V 4000W 4900W Protection category ENCLOSURE IP43 (electronic components), IP22 (connection area) SmartSolar MPPT 75/10, 75/15, Bluetooth Smart built-in dongle not needed The wireless solution to set-up, monitor and update the controller using Apple and Android smartphones, tablets or other devices. BlueSolar Controller MPPT 75/10 SmartSol MPPT75/10 MPPT 75/15 SmartSol MPPT75/15 Prices excluding VAT R1 248 R /24V Auto Selec Rated charge current 10A 15A Nominal PV power, 12V 145W 220W Nominal PV power, 24V 290W 440W Protection category ENCLOSURE IP43 (electronic components), IP22 (connection area) SmartSolar MPPT 100/15 & 100/20 Bluetooth Smart built-in dongle not needed The wireless solution to set-up, monitor and update the controller using Apple and Android smartphones, tablets or other devices. BlueSolar Controller MPPT 100/15 SmartSol MPPT100/15 MPPT 100/20 Prices excluding VAT R1 574 R /24V Auto Selec Rated charge current 15A 20A Nominal PV power, 12V Nominal PV power, 24V Protection category ENCLOSURE 220W 440W 290W 580W IP43 (electronic components), IP22 (connection area) SmartSolar MPPT 100/30 & 100/50 Solar charge controller. A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar maintains battery health, extending its life. BlueSolar Controller MPPT 100/30 MPPT 100/50 12/24V Auto Selec SmartSol MPPT100/30 SmartSol MPPT100/50 Prices excluding VAT R2 586 R3 710 Rated charge current 30A 50A Nominal PV power, 12V 440W 700W Nominal PV power, 24V 880W 1400W Protection category ENCLOSURE IP43 (electronic components), IP22 (connection area) SmartSolar MPPT 150/35 Ultrafast Maximum Power Point Tracking (MPPT) Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. BlueSolar Controller MPPT 150/35 12/24/48V Auto Select SmartSol MPPT150/35 Prices excluding VAT R3 710 Rated charge current Max. PV short circuit current 12V: 500W / 24V: 1000W / 36V: 1500W / 48V: 2000W 40A Maximum efficiency 98% Protection category ENCLOSURE IP43 (electronic components), IP22 (connection area) SmartSolar MPPT 150/45 & 150/60 Choose between TR or MC4 terminal BlueSolar Controller MPPT 150/45 MPPT 150/60 Prices excluding VAT R5 622 R /24V Auto Selec Rated charge current 45A 60A Nominal PV power, 12V 650W 860W Nominal PV power, 24V 1300W 1720W ENCLOSURE IP43 (electronic components), Protection category IP22 (connection area) visit website for full spec and download on the SmartSolar MPPT

14 SmartSolar MPPT 150/70 & 150/85 Choose between TR or MC4 terminal SmartSolar MPPT 150/100 & 250/60 Choose between TR or MC4 terminal SmartSolar MPPT 250/70 & 250/85 Choose between TR or MC4 terminal BlueSolar Controller Prices excluding VAT Rated charge current Nominal PV power, 12V Nominal PV power, 24V Protection category MPPT 150/70 MPPT 150/85 SmartSolMPPT150/70TR SmartSolMPPT150/70MC SmartSolMPPT150/85TR SmartSolMPPT150/85MC R A 1000W 2000W ENCLOSURE TR - R7 870 MC- R /24V Auto Selec 85A 1200W 2400W IP43 (electronic components), IP22 (connection area) BlueSolar Controller MPPT 150/100 MPPT 250/60 SmartSMPPT150/100TR SmartSMPPT150/100MC Prices excluding VAT R8 995 R /24V Auto Selec Rated charge current 100A 60A Nominal PV power, 12V 1450W 860W Nominal PV power, 24V 2900W 1720W Protection category ENCLOSURE IP43 (electronic components), IP22 (connection area) BlueSolar Controller MPPT 250/70 MPPT 250/85 12 / 24 / 48V Auto Select (software tool needed to select 36V) SmartSolMPPT250/85TR SmartSolMPPT250/85MC Prices excluding VAT R8 433 R9 556 Rated charge current 70A 85A Nominal PV power, 12V 1000W 1200W Nominal PV power, 24V 2000W 2400W Maximum PV power, 48V 4000W 4900W Protection category ENCLOSURE IP43 (electronic components), IP22 (connection area) MPPT Control (VE.Direct cable not included) VE.Direct non inverting remote on-off cable R225 SmartSolar Pluggable Display Order code: SmartSolPlug Display Price excl.vat: R56200 MPPT Control Order code: Mppt Control Price excl.vat: R900 SmartSolar 250/100 Optional: pluggable LCD display Remove the seal that protects the plug on the front of the controller, and plug-in the display BlueSolar Controller MPPT 250/100 Prices excluding VAT Rated charge current Nominal PV power, 12V Nominal PV power, 24V Nominal PV power, 48V Protection category ENCLOSURE 12 / 24 / 48V Auto Select (software tool needed to select 36V) SmartSMPPT250/100TR SmartSMPPT250/100MC R R A 1450W 2900W 5800W IP43 (electronic components), IP22 (connection area) BlueSolar PWM-DUO 12/24V 20A PWM controller - Charges two separate batteries. For example the starter battery and the service battery of a boat or mobile home - Programmable charge current ratio (standard setting: equal current to both batteries) BlueSolar Controller 12/24-20 Rated charge current Prices excluding VAT R1 574 Second battery output Automatic load disconnect Protection category Charge voltage absorption ENCLOSURE 12/24 V with automatic system voltage detection 20A B/S PWM DUO12/24V Yes n. a IP V / 28,8V Charge voltage float 13.7V / 27,4V

15 PWM-Light 12/ /24V - Load output with low battery voltage disconnect function. - Lighting control function, one timer only. - Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. BlueSolar Controller 12/ /24 V with automatic system voltage detection B/S PWM LT 12/24-5A Prices excluding VAT R Rated charge current Automatic load disconnect Battery 5A Yes Charge voltage absorption 14.2V / 28,4V Charge voltage float 13.8V / 27,6V Low voltage load disconnect 11,2V / 22,4V PWM-Light 12/ /24V - Load output with low battery voltage disconnect function. - Lighting control function, one timer only. - Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. BlueSolar Controller 12/24-10 Rated charge current Prices excluding VAT R Automatic load disconnect Battery 12/24 V with automatic system voltage detection 10A B/S PWM LT 12/24-10A Yes Charge voltage absorption 14.2V / 28,4V Charge voltage float 13.8V / 27,6V Low voltage load disconnect 11,2V / 22,4V PWM-Light 12/ /24V - Load output with low battery voltage disconnect function. - Lighting control function, one timer only. - Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. BlueSolar Controller 12/24-20 Rated charge current Prices excluding VAT R Automatic load disconnect Charge voltage absorption Battery 12/24 V with automatic system voltage detection 20A B/S PWM LT 12/24-20A Yes 14.2V / 28,4V Charge voltage float 13.8V / 27,6V Low voltage load disconnect 11,2V / 22,4V PWM-Light 12/ /24V - Load output with low battery voltage disconnect function. - Lighting control function, one timer only. - Two digit seven segment display for quick and easy setting of the load output functionality, including timer setting. BlueSolar Controller 12/24-30 Rated charge current 12/24 V with automatic system voltage detection 30A B/S PWM LT 12/24-30A Prices excluding VAT R618 Automatic load disconnect Charge voltage absorption Battery Yes 14.2V / 28,4V Charge voltage float 13.8V / 27,6V Low voltage load disconnect 11,2V / 22,4V BlueSolar PWM-Light Day/night timing options - Load output with low battery voltage disconnect function. - Lighting control function, one timer only. - Seven segment display for quick and easy setting of the load output functionality, including timer setting BlueSolar Controller Prices excluding VAT R674 10A Automatic load disconnect Yes Maximum solar voltage 100 V Humidity (non-condensing) Max 95% Battery Bulk charge 58,0V (1) Charge voltage absorption 56,8V Charge voltage float 55,2V BlueSolar PWM-Light Day/night timing options - Load output with low battery voltage disconnect function. - Lighting control function, one timer only. - Seven segment display for quick and easy setting of the load output functionality, including timer setting BlueSolar Controller Automatic load disconnect 20A Yes Prices excluding VAT R866 Maximum solar voltage 100 V Humidity (non-condensing) Max 95% Battery Bulk charge 58,0V (1) Charge voltage absorption 56,8V Charge voltage float 55,2V

16 BlueSolar PWM-Light Day/night timing options - Load output with low battery voltage disconnect function. - Lighting control function, one timer only. - Seven segment display for quick and easy setting of the load output functionality, including timer setting BlueSolar Controller Prices excluding VAT R A Automatic load disconnect Yes Maximum solar voltage 100 V Humidity (non-condensing) Max 95% Battery Bulk charge 58,0V (1) Charge voltage absorption 56,8V Charge voltage float 55,2V BlueSolar PWM - PRO 12/24-5 Programmable The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable: - With help of a computer and software (available free of charge from our website) - With the dedicated BlueSolar Pro Remote Panel BlueSolar Controller 12/24-5 Automatic load disconnect 12/24V with automatic system voltage detection Yes B/S PWM-Pro12/24V-5A Prices excluding VAT R393 Maximum solar voltage Rated charge current Load output 28V / 55V (1) 5A Manual control + low voltage disconnect BlueSolar PWM - PRO 12/24-10 Programmable The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable: - With help of a computer and software (available free of charge from our website) - With the dedicated BlueSolar Pro Remote Panel BlueSolar Controller 12/24-10 Automatic load disconnect Prices excluding VAT R449 12/24V with automatic system voltage detection Yes B/S PWM-Pro12/24-10A Maximum solar voltage 28V / 55V (1) Rated charge current Load output 10A Manual control + low voltage disconnect BlueSolar PWM-Light Programmable The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable: - With help of a computer and software (available free of charge from our website) - With the dedicated BlueSolar Pro Remote Panel BlueSolar Controller 12/24-20 Prices excluding VAT R788 12/24V with automatic system voltage detection B/S PWM-Pro12/24-20A BlueSolar PWM - PRO 12/ Programmable The BlueSolar PWM-Pro series is ready for use with its default settings. It also is fully programmable: - With help of a computer and software (available free of charge from our website) - With the dedicated BlueSolar Pro Remote Panel BlueSolar Controller 12/24-30 Prices excluding VAT R /24V with automatic system voltage detection B/S PWM-Pro12/24-30A BlueSolar MPPT 150/70 Solar charge controller A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar Controller MPPT 150/70 BlueSol MPPT150/70 Automatic load disconnect Yes Automatic load disconnect Yes Prices excluding VAT R7 308 Maximum solar voltage 28V / 55V (1) Rated charge current Load output 20A Manual control + low voltage disconnect Maximum solar voltage 28V / 55V (1) Rated charge current Load output 30A Manual control + low voltage disconnect Maximum PV open circuit voltage 12 / 24 / 36 / 48V Auto Select 150V absolute maximum coldest conditions 145V start-up and operating maximum visit website for full spec and download on the PWM Chargers Minimum PV voltage Battery voltage plus 7 Volt to start

17 Inverting remote on-off cable BlueSolar MPPT 150/70 Solar charge controller A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar Controller MPPT 150/70 BlueSol MPPT150/70 Prices excluding VAT R7 308 BlueSolar MPPT 150/85 Solar charge controller A solar charger gathers energy from your solar panels, and stores it in your batteries. Using the latest, fastest technology, BlueSolar maximises this energy-harvest, driving it intelligently to achieve full charge in the shortest possible time. BlueSolar Controller MPPT 150/85 BlueSol MPPT150/85 Prices excluding VAT R Order code: Price excl.vat: R225 VE.Direct TX digital output cable (PWM light dimming cable) Rated charge current 40 C (104 F) Rated charge current 40 C (104 F) 12 / 24 / 36 / 48V Auto Select 12 / 24 / 36 / 48V Auto Select Maximum PV open circuit voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Maximum PV open circuit voltage 150V absolute maximum coldest conditions 145V start-up and operating maximum Minimum PV voltage plus 7 Volt to start Minimum PV voltage plus 2 Volt operating Maximum solar array input power 12V: 1000W / 24V: 2000W / 36V: 3000W / 48V: 4000W Maximum solar array input power 12V: 1200W / 24V: 2400W / 36V: 3600W / 48V: 4850W Order code: visit website for full spec and download on the Blue- Solar MPPT Chargers Price excl.vat: R Which solar charge controller: PWM or MPPT? PWM and MPPT charge controllers are both widely used to charge batteries with solar power. The PWM controller is in essence a switch that connects a solar array to the battery. The result is that the voltage of the array will be pulled down to near that of the battery. The MPPT controller is more sophisticated (and more expensive): it will adjust its input voltage to harvest the maximum power from the solar array and then transform this power to supply the varying voltage requirement of the battery plus load. Thus, it essentially decouples the array and battery voltages so that there can be, for example, a 12 volt battery on one side of the MPPT charge controller and panels wired in series to produce 36 volts on the other. It is generally accepted that MPPT will outperform PWM in a cold to temperate climate, while both controllers will show approximately the same performance in a subtropical to tropical climate. In this paper the effect of temperature is analyzed in detail, and a quantitative performance comparison of both controller topologies is given. Conclusion: In order to get the maximum out of a solar panel, a charge controller should be able to choose the optimum current-voltage point on the current-voltage curve: the Maximum Power Point. An MPPT controller does exactly that. The input voltage of a PWM controller is, in principle, equal to the voltage of the battery connected to its output (plus voltage losses in the cabling and controller). The solar panel, therefore, is not used at its Maximum Power Point, in most cases. Remote panel for BlueSolar PWM-Pro Order code: B/S PWM-PRO REMOTE Price excl.vat: R BlueSolar PWM-Pro to USB interface cable Order code: B/S PWM-Pro to USB Price excl.vat: R134 Temperature sensor for BlueSolar PWM-Pro Order code: Temp/sensor-PWM-Pro Price excl.vat: R Remote Panel for BlueSolar DUO 12/24V-20A Order code: RemotePanBluSol DUO Price excl.vat: R

18 Battery Chargers Victron Energy offers an extensive range of chargers that can accommodate a wide variety of battery types. These technologically advanced chargers are built to withstand tough environmental conditions such as heat, humidity and salt air. The Victron Energy chargers include built-in battery controllers and fully monitored battery capacity to ensure optimal performance. Some of the devices in our Blue Power range are completely encapsulated; making them waterproof, shockproof and ignition protected. When compared to the industry standard, Victron Energy battery chargers outperform on every level. visit website for full spec and download on the Phoenix Chargers Phoenix Charger 12/30 12 / 24 Volt Adaptive 4-stage charge characteristic: bulk - absorption - float - storage. Two full rated outputs and one 4 Amp output. Phoenix Charger 12/50 12 / 24 Volt Adaptive 4-stage charge characteristic: bulk - absorption - float - storage. Two full rated outputs and one 4 Amp output. Phoenix Charger 24/16 12 / 24 Volt Adaptive 4-stage charge characteristic: bulk - absorption - float - storage. Two full rated outputs and one 4 Amp output. Phoenix Charger 12/30 Input voltage range (V AC) Charge voltage absorption 14,4 Charge voltage float 13,8 Battery capacity (Ah) Battery-connection M6 studs PhoenixCharger12/30 R5 441 Accessories Battery Alarm Phoenix charge control Phoenix Charger 12/50 Input voltage range (V AC) Charge voltage absorption 14,4 Charge voltage float 13,8 Battery capacity (Ah) Battery-connection M6 studs PhoenixCharger 12/50 R7 274 BMV-700 Battery Monitor Phoenix Charger 24/16 Input voltage range (V AC) Charge voltage absorption 28,8 Charge voltage float 27,6 Battery capacity (Ah) Battery-connection M6 studs PhoenixCharger 24/16 R5 441 Phoenix Charger 24/25 12 / 24 Volt Adaptive 4-stage charge characteristic: bulk - absorption - float - storage. Two full rated outputs and one 4 Amp output. An excessively high or low battery voltage is indicated by an audible and visual alarm, and potential free contacts. : Battery Alarm GX : R788 The PCC panel provides remote control and monitoring of the charge process with LED indication of the charger status : PhoenixCharControl : R1 012 The BMV-700 Battery Monitor features an advanced icroprocessor control system combined with high resolution measuring systems for battery voltage and charge/ discharge current. : BMV-700 : R1 641 Phoenix Charger 24/16 Input voltage range (V AC) Charge voltage absorption ,8 Charge voltage float 27,6 Battery capacity (Ah) Battery-connection M6 studs PhoenixCharger 24/25 R7274

19 24 Volt Skylla-i 24Volt 24 Volt Skylla-i 24Volt 24 Volt Skylla-i 24Volt A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i 24/80 (1+1) Skylla-i 24/80 (3) Skylla-i 24/100 (1+1) Input voltage range (VAC) V Input voltage range (VAC) V Input voltage range (VAC) V Maximum AC input 180 VAC 16 A Maximum AC input 180 VAC 16 A Maximum AC input 180 VAC 20 A Charge current (A) 80 A Charge current (A) 3 X 80 A Charge current (A) 100 A Charge current starter batt. Battery capacity (Ah) 4 A Ah Skylla-I 24/80(1+1) R Skylla-i remote on-off cable Charge current starter batt. 4 A Battery capacity (Ah) Ah Skylla-i 24/80(3) R Charge current starter batt. Battery capacity (Ah) 4 A Ah Skylla-I 24/100(1+1) R Order code: Price excl.vat: R374 Skylla-i 24Volt Skylla-TG Charger 24Volt Skylla-TG Charger 24Volt / 3 phase 24 Volt 24 Volt 24 Volt A modern and powerful battery charger that withstands the rigors of an adverse environment: heat, humidity and salt air. Skylla-i 24/100 (3) Input voltage range (VAC) Maximum AC input 180 VAC Charge current (A) Charge current starter batt. Battery capacity (Ah) V 16 A 3 x 100 A (max total output: 100A) 4 A Ah Skylla-i 24/100(3) R One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. 24/30 TG 24/50 TG 24Volt / 30A 24Volt / 50A Input voltage range (VAC) 230 Input voltage range (V AC) Input voltage range (V DC) Charge current starter batt. 4 A Battery capacity (Ah) Skylla-TG 24/30 Skylla-TG 24/50 R7 949 R8 601 One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. 24/50 TG 3 phase 24Volt / 50A Input voltage range (VAC) 3 x 400 Input voltage range (V AC) Input voltage range (V DC) n. a. Charge current starter batt. 4 A Battery capacity (Ah) SkyllaTG 24/50-3Phas R15 616

20 visit website for full spec and download on the Skylla Chargers Skylla-TG Charger 24Volt 24 Volt One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. 24/80 TG 24/100 TG 24Volt / 80A 24Volt / 100A Input voltage range (VAC) 230 Input voltage range (V AC) Input voltage range (V DC) Charge current starter batt. 4 A Battery capacity (Ah) Skylla-TG 24/80 Skylla-TG 24/100 R R Skylla-TG Charger 24Volt - 3 phase 24 Volt One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. 24/100 TG 3 phase 24Volt / 100A Input voltage range (VAC) 3 x 400 Input voltage range (V AC) Input voltage range (V DC) n. a. Charge current starter batt. 4 A Battery capacity (Ah) SkyllaTG24/100-3Phas R Skylla-TG Charger 24Volt VAC 24 Volt Skylla-TG 24/30 (1+1) Skylla-TG 24/50 (1+1) Skylla-TG 24/100 (1+1) Input voltage range (VAC) Input voltage range (V DC) Charge current starter batt. Battery capacity (Ah) 24Volt / 30A 24Volt / 50A 24Volt / 100A A 30 (limited to 22 A at 110V AC) SkyllaTG24/100-G 90 R Skylla-TG Charger 48Volt 48 Volt Skylla IP44 12 & 24Volt 12 / 24 Volt Skylla-TG GMDSS- 24Volt 24 Volt One full rated output and one 4 Amp output. Charge voltage can be precisely adjusted to suit any battery system. 48/25 TG 48/50 TG 48Volt / 25A 48Volt / 50A Input voltage range (VAC) 230 Input voltage range (V AC) Input voltage range (V DC) Charge current starter batt. n. a Battery capacity (Ah) Skylla-TG 48/25 Skylla-TG 48/50 R R Skylla IP44 12/60 (1+1) Skylla IP44 12/60 (3) Skylla IP44 24/30 (1+1) Skylla IP44 24/30 (3) Input voltage range (VAC) Charge current starter batt. Battery capacity 12Volt / 60A 12Volt / 60A / 3Phase 24Volt / 60A 24Volt / 60A / 3Phase 120/230 V n. a Ah SkyllaIP44 12/ SkyllaIP44 12/60 (3) SkyllaIP44 24/ SkyllaIP44 24/30 (3) R8 882 R9 781 R8 882 R9 781 The Victron Skylla-TG 24/30 and 24/50 GMDSS Chargers have been designed to provide all required monitoring and alarm data. Skylla-TG 24/30 Skylla-TG 24/50 24Volt / 30A 24Volt / 50A Input voltage range (VAC) 230 Input voltage range (V AC) Frequency (Hz) Power factor 1 Charge current (A) 30 (limited to 22 A at 110 V AC) Skylla-TG24/30 GMDSS Skylla-TG24/50 GMDSS R R15 268

21 Centaur Charger 12Volt 12 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 12/20 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 20A CentaurCharger 12/20 R3 833 Centaur Charger 12Volt 12 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 12/30 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 30/16A CentaurCharger 12/30 R4 160 Centaur Charger 12Volt 12 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 12/40 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 40A CentaurCharger 12/40 R5 510 Centaur Charger 12Volt 12 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 12/50 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 50A CentaurCharger 12/50 R5 734 Centaur Charger 12Volt 12 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 12/60 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 60/30A CentaurCharger 12/60 R5 959 Centaur Charger 12Volt 12 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 12/80 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 80/40A CentaurCharger 12/80 R9 895

22 Centaur Charger 12Volt 12 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 12/100 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 100/60 CentaurCharger12/100 R Centaur Charger 24Volt 24 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 24/16 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 30/16 CentaurCharger 24/16 R4 970 Centaur Charger 24Volt 24 Volt Skylla-IP44 24/30 (3) Input voltage range (VAC) Input voltage range (VAC) Maximum AC input 100 VAC 120/230 V V 10 A Power factor 0,98 Charge current (A) 3 x 30 A (max total output: 30 A) CentaurCharger 24/30 R6 948 Centaur Charger 24Volt 24 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 24/40 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 80/40 CentaurCharger 24/40 R9085 Centaur Charger 24Volt 24 Volt The new Centaur range of battery chargers from Victron Energy have been designed to be a true world-wide product. Centaur Charger 24/60 Input voltage range (VAC) Input voltage range (V DC) Frequency (Hz) Power factor 1 Charge current (A) 100/60 CentaurCharger 24/60 R Installation made easy 1. Fasten the separate mounting plate (A) to the wall where you want to place the battery charger, and simply hook up the Centaur. 2. Secure the bottom of the backside (B) to the wall. visit website for full spec and download on the Centaur Chargers

23 Check the status of your battery remotely The Blue Smart IP22 is equipped with built-in Bluetooth, so the status of the charger and the battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be configured with the VictronConnect app. Recovery of deeply-discharged dead batteries Unlike other brands, the Blue Smart IP22 Charger will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Normal charging will then be resumed as soon as there is sufficient voltage across the battery terminals. BUILD IN BLUETOOTH BUILD IN BLUETOOTH BUILD IN BLUETOOTH Blue Smart IP22 Charger 12Volt 12 Volt The Blue Smart IP22 Charger is the new professional battery charger with built-in bluetooth. Blue Smart Charger Input voltage range (VAC) Charge current, normal mode 12V, 1 output 15 / 20 / 30A VAC 15 / 20 / 30 A Efficiency 93% Charge current, NIGHT or LOW 7,5 / 10 / 15 A Number of outputs 1 BlueSmartIP22 12/15 BlueSmartIP22 12/20 BlueSmartIP22 12/30 15A - R A - R A - R2248 Blue Smart IP22 Charger 12Volt 12 Volt The Blue Smart IP22 Charger is the new professional battery charger with built-in bluetooth. Blue Smart Charger Input voltage range (VAC) Charge current, normal mode 12V, 3 outputs 15 / 20 / 30A VAC 15 / 20 / 30 A Efficiency 93% Charge current, NIGHT or LOW 7,5 / 10 / 15 A Number of outputs 3 BlueSmartIP22 12/15A BlueSmartIP22 12/20A BlueSmartIP22 12/30A 15A: R A: R A: R2552 Blue Smart IP22 Charger 24Volt 24 Volt The Blue Smart IP22 Charger is the new professional battery charger with built-in bluetooth. Blue Smart Charger Input voltage range (VAC) Charge current, normal mode 24V, 1 output 8 / 12 / 16A VAC 8/12/15 A Efficiency 94% Charge current, NIGHT or LOW 4 / 6 / 8 A Number of outputs 1 R1 574 R1 934 R2 305

24 Bluetooth Smart The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available. Check the status of your battery remotely High efficiency With up to 94% efficiency, these chargers generate up to four times less heat when compared to the industry standard. And once the battery is fully charged, power consumption reduces to 0,5 Watt, some five to ten times better than the industry standard. Adaptive 6-stage charge algorithm: test - bulk absorption - recondition float storage The Blue Smart Charger features a microprocessor The controlled Blue Smart adaptive IP22 is equipped battery management. The adaptive feature will automatically optimize Bluetooth, the charging so the status process of the relative charger to and the the with built-in way the battery is being used. battery can be checked on a smartphone, tablet or laptop. All settings of the charger can be Storage Mode: less maintenance and aging when configured the battery with the is VictronConnect not in use app. The storage mode kicks in whenever the battery has not been subjected to discharge during 24 hours. In the storage mode float voltage is reduced to 2,2V/cell (13,2V for a 12V battery) to minimize gassing and corrosion of the positive plates. Once a week the voltage is raised back to the absorption level to equalize the battery. This feature prevents stratification of the electrolyte and sulfation, a major cause of early battery failure. Also charges Li-ion (LiFePO₄) batteries LiFePO₄ batteries are charged with a simple bulk absorption float algorithm. Recovery of deeply-discharged dead batteries NIGHT and LOW setting When in NIGHT or LOW mode, the output current is reduced to max. 50% of the nominal output and the charger will be totally noiseless. The NIGHT mode automatically ends after 8 hours. The LOW mode can be ended manually. Protected against overheating Output current will reduce as temperature increases up to 50 C, but the Blue Smart Charger will not fail. Unlike other brands, the Blue Smart IP22 Charger Eleven LEDs for status indication will attempt to recharge a deeply-discharged battery by force-feeding it with a low current. Charge algorithm: TEST / BULK / ABSORPTION / RECONDITION / FLOAT / STORAGE / Normal charging will then be resumed as soon READY. as there is sufficient voltage across the battery MODE button to set: NORMAL (14,4V) terminals. / HIGH (14,7V) / RECONDITION / LI-ION. BUILD IN BLUETOOTH Blue Smart IP22 Charger 24Volt 24 Volt The Blue Smart IP22 Charger is the new professional battery charger with built-in bluetooth. Blue Smart Charger Input voltage range (VAC) Charge current, normal mode 24V, 3 outputs 16A VAC 8/12/16 A Efficiency 94% Charge current, NIGHT or LOW 4 / 6 / 8 A Number of outputs 3 BlueSmartIP22 24/16A visit website for full spec and download on the BlueSmart IP22 Chargers R2619

25

26 visit website for full spec and download on the BlueSmart IP67 Chargers Blue Smart IP67 Charger Waterproof The Blue Smart IP67 Waterproof Charger is the new professional battery charger with built-in bluetooth. The Blue Smart IP67 Waterproof Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans. BUILD IN BLUETOOTH BUILD IN BLUETOOTH BUILD IN BLUETOOTH Blue Smart IP67 Charger Waterproof Blue Smart IP67 Charger Waterproof Blue Smart IP67 Charger Waterproof 12 Volt The Blue Smart IP67 Waterproof Charger is the new professional battery charger with built-in bluetooth. Blue Smart IP67 Charger Input voltage range (VAC) Charge current, LOW Charge current normal Charge algorith Can be used as power supply 12/7 12/ VAC 2A 7A 5 stage adaptive yes BlueSmart IP67 12/7 BlueSmart IP67 12/13 R1181 R Volt The Blue Smart IP67 Waterproof Charger is the new professional battery charger with built-in bluetooth. Blue Smart IP67 Charger Input voltage range (VAC) Charge current, LOW Charge current normal Charge algorith Can be used as power supply 12/17 12/ VAC 6A 17A 5 stage adaptive yes BlueSmart IP67 12/17 BlueSmtIP67 12/25(1) R1608 R Volt The Blue Smart IP67 Waterproof Charger is the new professional battery charger with built-in bluetooth. Blue Smart IP67 Charger Input voltage range (VAC) Charge current, LOW Charge current normal Charge algorith Can be used as power supply 24/5 24/8 24/ VAC 6A 17A 5 stage adaptive yes BlueSmtIP67 24/5(1) BlueSmart IP67 24/8 - Price on R1608 R2092

27 visit website for full spec and download on the BluePower IP67 Chargers

28 * Water, dust and chemical resistant * Seven step smart charge algorithm * Recovery of fully discharged dead batteries * Automatic power supply function * Severe cold performance: down to -30 C * Several other battery life enhancing features * Low power mode to charge smaller batteries * Li-ion battery mode * Setup and configure, readout of voltage and currentby Bluetooth Smart BUILD IN BLUETOOTH BUILD IN BLUETOOTH BUILD IN BLUETOOTH Blue Smart IP65 Charger 4-7A 12 Volt Blue Smart IP65 Charger 10 & 15A 12 Volt Blue Smart IP65 Charger 24 Volt The Blue Smart IP65 Charger is the new professional battery charger with built-in bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans. Blue Smart IP65 Charger Input voltage range (VAC) 12 V 4/5/7 A VAC Efficiency 94% Standby power consumption Can be used as power supply 0,5 W Yes BlueSmart IP65 12/4 BlueSmart IP65 12/5 BlueSmart IP65 12/7 R844 R888 R1 237 The Blue Smart IP65 Charger is the new professional battery charger with built-in bluetooth. The Blue Smart IP65 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans. Blue Smart IP65 Charger 12 V 10/15A Input voltage range (VAC) VAC Efficiency 94% Standby power consumption Can be used as power supply 0,5 W Yes BlueSmart IP65 12/10 BlueSmart IP65 12/15 R1 462 R1 686 The Blue Smart IP65 Charger is the new professional battery charger with built-in bluetooth. Blue Smart IP65 Charger Input voltage range (VAC) 24 V 5/8 A VAC Efficiency 95% Standby power consumption Charge current Low current mode Can be used as power supply 0,5 W 5 / 8 A 2 / 3 A Yes BlueSmart IP65 24/8 R1237 R1686

29 Accessories for the Blue Power IP65 Charger M6 eyelet connector (with 30A ATO fuse) M6 eyelet connector R67 M8 eyelet connector (with 30A ATO fuse) 0 R67 2 meter extension cable 2 Meter ext cable R90 12 Volt plug (cigarette plug with 16A fuse) R147 Clamp connector (with 30A ATO fuse) Clamp connector R134 Battery indicator panel (M8 eyelet connector/30a ATO) 0 R236 Battery indicator panel (M8 eyelet / 30A ATO Fuse) 0 R147 Rubber bumber for IP65 Charger 12/10, 12/15, 24/8 R67 Wall Mount for IP65 Charger 12/10,12/15,24/8 R56 Battery indicator panel Wall Mount for IP65 Charger 12/10,12/15,24/8 Rubber bumber for IP65 Charger 12/10, 12/15, 24/8 Automotive IP65 Charger 6 / 12 Volt Depending on the application, clamps, eyelets or a cigarette plug (all included) can be connected to the charger. Low power charger for 6V and 12V batteries: IP65 Charger 6V/12V-1,1A Charger for 12V batteries with two charge current options: IP65 Charger 12V/4A 12V/0,8A Automotive IP65 Charger Input voltage range Frequency Charge voltage Battery capacity range Charge current Can be used as power supply Back current drain V 50/60Hz 7,2 or 14,4 V 1,2 Ah 30 Ah 1,1 A max. No (output relay) 3 Ah/month (4 ma) AutomotiveIP65 6/12V AutomotiveIP65 12V R449 R529 visit website for full spec and download on the BluePower IP65 Chargers

30 : Smartbatterysense : R449 Smart Battery Sense Voltage and Temperature sense Smart Battery Sense is a wireless battery voltage and temperature sensor for Victron MPPT Solar Chargers. With voltage and temperature sense in place, batteries will be better charged; improving charging-efficiency and prolonging battery life. Both for lead, and for lithium batteries. Improves battery charging By measuring voltage at the battery bank terminals, errors arising from voltage-loss due to cable resistance are avoided - guaranteeing the correct charge-voltage. For lead batteries, battery temperature data is used to adjust the charge-voltages: cold batteries require an increased charge-voltage, whereas hot batteries require a decreased charge-voltage. For lithium batteries temperature data is used to disable charging when they are too cold: charging lithium batteries near or below freezing causes permanent damage to the cells.

31 Battery Protectors Battery protectors are responsible for disconnecting your loads before the battery is flat. This prevents unnecessary damage to your battery. Other beneficial features include auto ranging which automatically detects system voltage, over voltage protection which prevents damage to sensitive loads and delayed alarm output and delayed load disconnect. To ensure the quality and longevity of your battery, equip it with a Victron Energy battery protector. We have a selection of products to choose from in order to accommodate your specific requirements. visit website for full spec and download on the Battery Protectors BatteryProtect 48 The BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. BatteryProtect Maximum continuous load current Peak current 100A 250A Operating voltage range 24 64V Current consumption Alarm output delay Maximum load on alarm Output When on: 2 ma When off or low voltage shutdown : 0,8 ma 12 seconds 50 ma (short circuit proof) BatteryProtect 48V R1 518 BatteryProtect 65 The BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. BatteryProtect 65 Maximum continuous load current Peak current 65A 300A Operating voltage range 6 35V Current consumption Alarm output delay Maximum load on alarm Output When on: 1,5 ma When off or low voltage shutdown : 0,6 ma 12 seconds 50 ma (short circuit proof) BatteryProtect-65A R462 BatteryProtect 100 The BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. BatteryProtect 100 Maximum continuous load current Peak current 100A 600A Operating voltage range 6 35V Current consumption Alarm output delay Maximum load on alarm Output When on: 1,5 ma When off or low voltage shutdown : 0,6 ma 12 seconds 50 ma (short circuit proof) BatteryProtect-100A R674 BatteryProtect 220 Maximum continuous load current 220A Battery Balancer The Battery Balancer equalizes the state of charge of two series connected 12V batteries, or of several parallel strings of series connected batteries. : Battery Balancer : R753 BatteryProtect 220 The BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. Peak current 600A Operating voltage range 6 35V Current consumption Alarm output delay Maximum load on alarm Output When on: 1,5 ma When off or low voltage shutdown : 0,6 ma 12 seconds 50 ma (short circuit proof) BatteryProtect-220A R1 114

32 Autotransformer The Autotransformer: for step up, step down and split phase balancing An Autotransformer can be used for step up, step down and split phase output balancing purposes. While the step up and step down functions are fairly straightforward, split phase output balancing may require some more attention. visit website for full spec and download on the Autrotransformers Autotransformer 32A The Autotransformer: for step up, step down and split phase balancing An Autotransformer can be used for step up, step down and split phase output balancing purposes. While the step up and step down functions are fairly straightforward, split phase output balancing may require some more attention. Autotransformer 100A The Autotransformer: for step up, step down and split phase balancing An Autotransformer can be used for step up, step down and split phase output balancing purposes. While the step up and step down functions are fairly straightforward, split phase output balancing may require some more attention. Autotransformer 32A Autotransformer 100A Input/output voltage 120 / 240V Input/output voltage 120 / 240V Input circuit breaker 32A, two pole Input circuit breaker 100A, two pole Frequency 50/60Hz Frequency 50/60Hz Maximum 240 V feed through current 32A Maximum 240 V feed through current 100A Neutral current, 30 min 32A (3800 VA) Neutral current, 30 min 32A (3800 VA) Transformer type Toroidal Transformer type Toroidal ATFormer 120/240 32A R6 307 ATFormer120/ A R8 038 visit website for full spec and download on the Galvanic Isolators Autotransformer VDI-16 VDI-32 Galvanic Isolator The galvanic isolator consists internally of two diodes which are connected in anti-parallel fashion. When they are connected in this way, the diodes allow current in both directions but only above a certain threshold voltage. The voltage at which diodes conduct is about 1.4 Vdc. Peak current 1600 A / 20 ms 1600 A / 20 ms Max current 16 A 32 A Dimensions H x W x D mm 60 x 120 x x 164 x 235 Weight kg (lbs) 1 (2.2) 2 (4.4) Galvanic.Isol VDI-16 Galvanic.Isol VDI-32 R1 214 R2 474

33 Isolation Transformers 2000VA / 3600VA / 7000VA Indispensable in professional marine energy systems. It prevents electrolytic corrosion and above all serves as a device to guarantee a safe electric system. Toroidal wound technology for quietness and high efficiency. Soft start circuitry will ensure that the shore circuit breaker will not trip when plugged in. Isolation Transformers 2000VA Indispensable in professional marine energy systems. It prevents electrolytic corrosion and above all serves as a device to guarantee a safe electric system. Toroidal wound technology for quietness and high efficiency. Soft start circuitry will ensure that the shore circuit breaker will not trip when plugged in. Isolation Transformers 2000 Watt (1) Input Output Frequency Rating Soft start Transformer type 115 or 230 V 115 or 230 V 50/60Hz 17 / 8,5 A Yes Toroidal (low noise, low weight) IsolationTrans.2000 R5 847 Isolation Transformers 3600VA Indispensable in professional marine energy systems. It prevents electrolytic corrosion and above all serves as a device to guarantee a safe electric system. Toroidal wound technology for quietness and high efficiency. Soft start circuitry will ensure that the shore circuit breaker will not trip when plugged in. Isolation Transformers 3000 Watt (1) Input Output Frequency Rating Soft start Transformer type 115 or 230 V 115 or 230 V 50/60Hz 32 / 16 A Yes Toroidal (low noise, low weight) IsolationTrans.3600 R8 252 Isolation Transformers 7000VA Indispensable in professional marine energy systems. It prevents electrolytic corrosion and above all serves as a device to guarantee a safe electric system. Toroidal wound technology for quietness and high efficiency. Isolation Transformers 7000 Watt (1) Input Output Frequency Rating Soft start Transformer type 230 V 230 V 50/60Hz 32 A Yes Toroidal (low noise, low weight) IsolationTrans.7000 R Victron Isolation Transformer 3600W 115/230V 32/16A The isolation transformer eliminates any electrical continuity between AC shore power and the boat. It is essential for safety and eliminates the need for galvanic isolators and polarity alarms. : IsolationTrans3600AU : R9 286 visit website for full spec and download on the Isolation transformers

34 DC-DC converters The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual).. -Tr DC-DC Converters Isolated With galvanic isolation 12 / 24 / 48 Volt Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual). Adjustable output voltage: can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24V system. All models are short circuit proof and can be paralleled to increase output current An unlimited number of units can be connected in parallel. 12V Isolated converters W -Tr 12/12-9 (110W) -Tr 12/12-18 (220W) -Tr 12/12-30 (360W) -Tr 12/24-5 (120W) -Tr 12/24-10 (240W) -Tr 12/24-15 (360W) Input voltage range 8-17V 8-17V 10-17V 8-17V 8-17V 10-17V Under voltage shut down 7V 7V 7V 7V 7V 7V Under voltage restart 7,5V 7,5V 7,5V 7,5V 7,5V 7,5V Nominal output voltage 12,2V 12,2V 12,2V 24,2V 24,2V 24,2V Output voltage adjust range 10-15V 10-15V 10-15V 20-30V 20-30V 20-30V -Tr 12/12-9A -Tr 12/12-18A -Tr 12/12-30A -Tr 12/24-5A -Tr 12/24-10A R742 R1338 R2744 R742 R1338 R V Isolated converters W -Tr 24/12-9 (110W) -Tr 24/12-20 (240W) -Tr 24/12-30 (360W) -Tr 24/24-5 (120W) -Tr 24/24-12 (280W) -Tr 24/24-17 (400W) -Tr 24/48-2,5 (120W) -Tr 24/48-6 (280W) -Tr 24/ (120W) Input voltage range 16-35V 16-35V 20-35V 16-35V 16-35V 20-35V 16-35V 16-35V 20-35V Under voltage shut down Under voltage restart Nominal output voltage Output voltage adjust range 14V 14V 14V 14V 14V 14V 14V 14V 14V 15V 15V 15V 15V 15V 15V 15V 15V 15V 12,2V 12,2V 12,2V 24,2V 24,2V 24,2V 48,2V 48,2V 48,2V 10-15V 10-15V 10-15V 20-30V 20-30V 20-30V 40-60V 40-60V 40-60V -Tr 24/12-9 -TR 24/12-20A -Tr 24/ Tr 24/24-5A -Tr 24/24-12A -Tr 24/48-2,5A R742 R1338 R2744 R742 R1338 R2474 R742 R1338 R V Isolated converters W -Tr 48/12-9A (110W) -Tr 48/12-20A (240W) -TR 48/12-30A (360W) -Tr 48/24-5A (120W) -TR 48/24-12A (280W) -TR 48/24-16A (380W) -Tr 48/48-2,5A (120W) -Tr 48/48-6A (280W) -TR 48/48-8A (380W) Input voltage range 16-35V 32-70V 40-70V 32-70V 32-70V 40-70V 32-70V 32-70V 40-70V Under voltage shut down Under voltage restart Nominal output voltage Output voltage adjust range 14V 28V 28V 28V 28V 28V 28V 28V 28V 15V 30V 30V 30V 30V 30V 30V 30V 30V 48,2V 12,2V 12,2V 24,2V 24,2V 24,2V 48,2V 48,2V 48,2V 40-60V 10-15V 10-15V 20-30V 20-30V 20-30V 40-60V 40-60V 40-60V -Tr 48/12-9A -Tr 48/12-20A -Tr 48/24-5A -Tr 48/48-2,5A R742 R1338 R2744 R742 R1338 R2474 R742 R1338 R2474

35 isolated 100W isolated 360W DC-DC Converters Isolated With galvanic isolation 12 / 24 / 48 Volt Remote on-off The remote on-off eliminates the need for a high current switch in the input wiring. The remote on-off can be operated with a low power switch or by for example the engine run/stop switch (see manual). 12V Isolated converters W 12/12-8,3A (100W) 12/12-17A (200W) 12/12-30A (360W) 12/24-4,2A (100W) 12/24-8,3A (200W) 12/24-10A (240W) 12/24-15A (360W) Power rating (W) 100W 200W 360W 100W 200W 240W 360W Galvanic isolation Yes Yes Yes Yes Yes Yes Yes V and A 12V/8.3A 12V/17A 12V/30A 12V/4.2A 12V/8.3A 12V/10A 12V/15A 12/12-30A 12/24-15A Price on Price on R2 001 Price on Price on Price on R V Isolated converters W 24/12-8,3A (100W) 24/12-17A (200W) 24/12-30A (360W) 24/24-4,2A (100W) 24/24-8,3A (200W) 24/24-15A (360W) 24/48-4,2A (200W) 24/48-7,5A (360W) Power rating (W) 100W 200W 360W 100W 200W 240W 360W 360W Galvanic isolation Yes Yes Yes Yes Yes Yes Yes Yes V and A 24V/8.3A 24V/17A 24V/30A 24V/4.2A 24V/8.3A 24V/15A 24V/4.2A 24/7.5A 24/12-17A 24/12-30A 24/24-4.2A 24/24-8.3A 24/24-15A 24/48-4.2A 24/48-7.5A Price on Price on Price on Price on Price on Price on R1705 R V Isolated converters W 48/12-8,3A (100W) 48/12-17A (200W) 48/12-30A (360W) 48/24-4,2A (100W) 48/24-8,3A (200W) 48/24-12A (280W) 48/24-15A (360W) 48/48-4,2A (200W) 48/48-7,5A (360W) Power rating (W) 100W 200W 360W 100W 200W 280W 360W 200W 360W Galvanic isolation Yes Yes Yes Yes Yes Yes Yes Yes V and A 48V/8.3A 48V/17A 48V/30A 48V/4.2A 48V/8.3A 48V/12A 48V/15A 48V/4.2A 48V/7.5A 48/12-8.3A 48/12-30A 48/24-4.2A 48/24-8.3A 48/24-15A 48/48-4.2A 48/48-7.5A Price on Price on Price on Price on Price on Price on Price on Price on Price on -Tr DC-DC Converters Non-isolated 24 Volt DC-DC converters High efficiency Using synchronous rectification, full load efficiency exceeds 95%. IP43 protection Non isolated converters -Tr 24/12-5 -Tr 24/ Tr 24/ Tr 24/12-20 Input voltage range 18-35V 18-35V 18-35V 18-35V Output voltage 12.7V 12.5V 12.5V 12.5V Efficiency 95% 97% 97% 97% Continuous output current 5A 10A 15A 20A Max. Output current 7A 12A 20A 25A -TR 24/12-5 -Tr 24/ Tr 24/ Tr 24/12-20 R203 R404 R462 R518 visit website for full spec and download on the DC-DC Converters

36 DC-DC Converters Non-isolated 12 Volt DC-DC converters All models with adjustable output can also be used as a battery charger For example to charge a 12 Volt starter or accessory battery in an otherwise 24 V system. Non isolated converters 12/ / /24-20 Input voltage range Undervoltage shutdown (V) Undervoltage restart (V) Output voltage (V) 24 Adjustable 20-30V F set 26,4V Adjustable 20-30V F set 26,4V Efficiency 95% 95% 93% Continuous output current 5A 10A 15A Max. Output current / / /24-20 R663 R810 R1822 DC-DC Converters Non-isolated 24 Volt Easy to install Delivery includes four Insulated Fastons Female Crimp 6.3 mm (eight Fastons in case of the 24/12-40). Non isolated converters 24/ / / / / /12-70 Input voltage range Undervoltage shutdown (V) Undervoltage restart (V) Output voltage (V) Adjustable 10 15V F set 13,2V 12 Adjustable 10 15V F set 13,2V Efficiency Continuous output current 5A 12A 17A 25A 40A 70A Max. Output current /12-5A 24/ / / / /12-70 R946 Price on Price on R1036 R1147 R1619 visit website for full spec and download on the DC-DC Converters

37 Victron Energy 12/27,6-12A (24V Charger Isolated) An ever-increasing amount of electric equipment is being used on vehicles and boats. Because most low-voltage equipment, such as navigation and radio equipment, mobile telephones or car hi-fi systems, is designed for 12V, Victron Energy supplies DC/DC converters which deliver a stable 12 Volt supply from a 24 Volt system. These products are also distinguished by high efficiency, together with absolute safety. Next to converters from 24V to 12V, a wide range of other models are available. : 12/27,6-12 : R2 675 Ultrafast transfer switch VICTRON ORION 7-35/12-3A ISOLATED BUCK-BOOST A super wide input range buck-boost regulator. The 7-35/12-3A is an isolated converter with a very wide input range, suitable for both 12V and 24V systems, and a fixed 12.6V output. : 7-35/12-3 : R1085 visit website for full spec and download on the DC-DC Converters The Filax has been designed to switch critical or sensitive loads, such as computers, industrial controls or modern entertainment equipment from one AC source to another. The priority source typically is the mains, a generator or shore power. The alternate source typically is an inverter. With its switching time of less than 20 milliseconds sensitive loads will continue to operate without disruption. The Filax is not intended to supply high power household equipment like washing machines, or electric motors Filax 2 110V/60Hz 240V/60Hz low voltage switching threshold low voltage reverse switching threshold high frequency reverse switching threshold Alternate source: maximum continuous input voltage 88V 92V 62Hz 58Hz Filax-2 110V/60Hz 180V 188V 68Hz 63Hz Filax-2 230V/50HZ R3936 R6497 DC-DC Converters Isolated, 360W 15A Isolated Converters Isolated Converters 110/24-15A (360W) Power rating (W) 360 Galvanic isolation Temperature increase after 30 minutes at full load ( C) Fan assisted cooling (temp. controlled) yes 30 yes 110/12-360W 110/24-360W R4070 R5699

38 DC-DC Converters Isolated, 360W 30A Isolated Converters Isolated Converters 110/12-30A (360W) Power rating (W) 360 Galvanic isolation Temperature increase after 30 minutes at full load ( C) Fan assisted cooling (temp. controlled) yes 30 yes 110/12-360W R4070 Not isolated, resin encapsulated IP67 24/12 DC-DC Converters 24 Volt Water, oil or dirt will not damage the IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin. IP67 24/12-5 Input voltage range Under voltage shutdown Under voltage restart No load current at 24V 15-40VDC 13V 14V 1mA DC output voltage 12V +/- 3% Maximum continuous output current 5A Efficiency 93% IP67 24/12-5 R304 Not isolated, resin encapsulated IP67 24/12 DC-DC Converters 24 Volt Water, oil or dirt will not damage the IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin. IP67 24/12-10 Input voltage range Under voltage shutdown Under voltage restart No load current at 24V 15-40VDC 13V 14V 20mA DC output voltage 12V +/- 3% Maximum continuous output current 10A Efficiency 93% IP67 24/12-10 R495 Not isolated, resin encapsulated IP67 24/12 DC-DC Converters 24 Volt Water, oil or dirt will not damage the IP67 DC- DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin. IP67 24/12-20 Input voltage range Under voltage shutdown Under voltage restart No load current at 24V 15-40VDC 13V 14V 50mA DC output voltage 12V +/- 3% Maximum continuous output current 20A Efficiency 95% IP67 24/12-20 R652 IP67 25A DC-DC Converters 12 Volt DC-DC Converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. Buck-Boost DC-DC Converter Buck-Boost DC-DC Converter 25A Input voltage range 7-35V Under voltage threshold 10V Output voltage range 2-30V Maximum charge current 12V : 25A 24V : 15A Converter off, LEDs off (power save mode) 7 ma On threshold voltage > 2V 25A Buck-Boost DC/DC R6026 IP67 50A DC-DC Converters 24 Volt DC-DC Converter for charging a 12/24V service battery in vehicles with an intelligent dynamo. Buck-Boost DC-DC Converter Buck-Boost DC-DC Converter 50A Input voltage range 7-35V Under voltage threshold 10V Output voltage range 2-30V Maximum charge current 12V : 50A 24V : 25A Converter off, LEDs off (power save mode) 7 ma On threshold voltage > 2V 50A Buck-Boost DC/DC R A Buck-Boost DC/DC converter R13 086

39 Battery monitors The essential function of a battery monitor is to calculate ampere hours consumed and the state of charge of a battery. Ampere hours consumed are calculated by integrating the current flowing in or out of the battery. visit website for full spec and download on the BMV BMV-700 series BMV-702 series BMV-700H series Battery Monitor Supply voltage range Current draw, back light off Input voltage range, auxiliary battery Battery capacity (Ah) Operating temperature range Measures voltage of second battery, or temperature, or midpoint BMV-700 6,5-95 VDC < 4mA n. a Ah C ( F) BMV-700 R1641 No Battery Monitor Supply voltage range Current draw, back light off Input voltage range, auxiliary battery Battery capacity (Ah) Operating temperature range Measures voltage of second battery, or temperature, or midpoint BMV-702 BMV-702 BLACK 6,5-95 VDC < 4mA 6,5-95 VDC Ah C ( F) Yes BMV-702 Battery Monitor Battery Monitor Supply voltage range Current draw, back light off Input voltage range, auxiliary battery Battery capacity (Ah) Operating temperature range Measures voltage of second battery, or temperature, or midpoint BMV-700HS VDC < 4mA n. a Ah C ( F) No R2047 Price on R7084 BMV-712 Smart Battery Monitor Battery Monitor Supply voltage range Current draw, back light off Input voltage range, auxiliary battery Battery capacity (Ah) Operating temperature range Measures voltage of second battery, or temperature, or midpoint BMV-712 Smart 6,5-70 VDC < 1mA 6,5-70 VDC Ah C ( F) BMV-712 Yes R2362 Battery Balancer The Battery Balancer equalizes the state of charge of two series connected 12V batteries, or of several parallel strings of series connected batteries. Victron Battery Balancer Up to 18V per battery, 36V total Input voltage range Turn on level 27,3V +/- 1% Turn off level 26,6V +/- 1% Current draw when off 0,7 ma Battery Balancer R753 Temperature sensor for BMV-702 : Temperature sensor for BMV-702 : R281

40 Lynx Power In A modular DC bus bar, used to connect batteries to the Lynx DC distribution system. : Lynx Power In : R1 574 Lynx Distributor A modular DC bus bar, with locations for four DC fuses. It will monitor the status of each fuse, and indicate its condition with a LED on the front. : Lynx Distributor : R2 362 Lynx Shunt VE.Net The Lynx Shunt VE.Net is an intelligent 1000A shunt with location for a fuse, the built in battery monitor accurately monitors the state of charge on your battery. Use the Blue Power Panel or VE.Net panel for reading out the information. Part of the modular Lynx distribution system. : Lynx Shunt VE.Net : R3 958 Lynx Shunt VE.Can The Lynx Shunt VE.Can is an intelligent 1000A shunt with location for a fuse, the built in battery monitor accurately monitors the state of charge of your battery. Use the Color Control GX for reading out the information. Part of the modular Lynx distribution system. : Lynx Shunt VE.Can : R3 958 Victron VE Transfer Switch 5/10kVA 230V The VE Transfer Switch has been designed to switch sensitive loads, such as computers or modern entertainment equipmentfrom one AC source to another. The priority source typically is the mains, a generator or shore power. : VE.TransSwitch 5KVA : R3 440 : VE.TransSwitch 10KVA : R4 262 visit website for full spec and download on the Lynx Shunt ESP DC Link Box (in plastic enclosure) The DC Link Box brings all the primary DC protection, DC monitoring and sensor connections into one simple to fit enclosure. It includes: * 4 Mega fuses (2x 300A, 1x 200A, 1x 100A) and 1 Midi fuse (60A). These can be changed to suit the user s requirements. Mega fuses are available in sizes from 100 to 500 amps and Midi fuses from 30 to 125 amps. * 500 Amp shunt. * Test button with LEDs for all 5 fuses and a polarity warning LED. * Fused connection points for MultiPlus voltage sense and BMV-600 connections. * Fused connections for magnetically latching battery isolator which can be controlled via ESP system panel. * RJ 11 and 45 socket connections for ESP system panel. : ESP DC Link Box : R4 486 Argo Diode Battery Combiners Diode Battery Combiners are used to guarantee continuous DC power to mission critical equipment, such as an electronic engine control system. With a Diode Battery Combiner two or more DC power sources can be used in parallel to supply the mission critical load. Failure of one source will not interrupt power to the critical load. Argo Diode Battery Combiner BCD 402 Maximum continuous current (A) Number of batteries 2 Connection 40 M6 bolts Weight kg (lbs) 0,8 (1.8) BCD302 2 BAT 30A BCD BAT 40A R392 R495 Argo Diode Battery Combiner BCD 802 Maximum continuous current (A) 60 Number of batteries 2 Connection M6 bolts Weight kg (lbs) 0,8 (1.8) BCD BAT 80A R607

41 Argo Diode Battery Isolators Diode battery isolators allow simultaneous charging of two or more batteries from one alternator, without connecting the batteries together. Discharging the accessory battery for example will not result in also discharging the starter battery. The Argo Battery Isolators feature a low voltage drop thanks to the use of Schottky diodes: at low current the voltage drop is approximately 0,3 V and at the rated output approximately 0,45 V. All models are fitted with a compensation diode that can be used to slightly increase the output voltage of the alternator. This compensates for the voltage drop over the diodes in the isolator. Please see our book Energy Unlimited or ask for specialist advice when installing a diode isolator. Simply inserting the isolator in the cabling between the alternator and the batteries will slightly reduce charge voltage. The result can be that batteries are not charged to the full 100% and age prematurely. Alternator energize input Some alternators need DC voltage on the B+ output to start charging. Obviously, DC will be present when the alternator is directly connected to a battery. Inserting a Diode or FET splitter will however prevent any return voltage/current from the batteries to the B+, and the alternator will not start. The new AC diode isolators feature a special current limited energize input that will power the B+ when the engine run/stop switch is closed. Argo Diode Battery Isolator 80-2SC 80-2AC 100-3AC 120-2AC 140-3AC 160-2AC 180-3AC Maximum charge current (A) Maximum alternator current (A) Number of batteries Alternator Energize Input no yes yes yes yes yes yes Connection M6 Studs M6 Studs M6 Studs M8 Studs M8 Studs M8 Studs M8 Studs Compensation diode and Energize connection 6,3 mm Faston 6,3 mm Faston 6,3 mm Faston 6,3 mm Faston 6,3 mm Faston 6,3 mm Faston 6,3 mm Faston Weight kg (lbs) 0,5 (1.3) 0,6 (1.3) 0,8 (1.8) 0,8 (1.8) 1,1 (2.5) 1,1 (2.5) 1,5 (3.3) ARGO 80-2SC 2BAT 80A ARGO 80-2AC 2BAT 80A ARGO100-3AC- 3BAT 100A ARGO120-2AC- 2BAT 120A ARGO140-3AC- 3BAT 140A ARGO160-2AC2BAT 160A ARGO180-3AC- 3BAT 180A R449 R574 R775 R866 R1090 R1034 R1259 Argo FET Battery Isolators Similarly to diode battery isolators, FET isolators allow simultaneous charging of two or more batteries from one alternator (or a single output battery charger), without connecting the batteries together. In contrast with diode battery isolators, FET isolators have virtually no voltage loss. Voltage drop is less than 0,02 Volt at low current and averages 0,1 Volt at higher currents. Argo FET Battery Isolator Argofet Argofet Argofet Argofet Maximum charge current (A) Maximum alternator current (A) Number of batteries Alternator Energize Input no yes yes yes Connection M8 bolts M8 bolts M8 bolts M8 bolts Weight kg (lbs) 1,4 (3.1) 1,4 (3.1) 1,4 (3.1) 1,4 (3.1) ARGOFET BAT100 ARGOFET BAT100 ARGOFET BAT200 ARGOFET BAT200 R1147 R1315 R1371 R1608 Microprocessor controlled battery combiner/isolators The Cyrix Battery Combiner is a microprocessor controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a preset voltage (indicating that the battery is being charged), and disconnects when the voltage decreases below float level (indicating that one or more batteries are being discharged). Cyrix Battery Combiners are an excellent replacement for diode isolators. The main feature is that there is virtually no voltage loss so that the output voltage of alternators or battery chargers does not need to be increased. LED status indicator

42 Cyrix-ct 12/24V-120A Battery combiner kit Cable and lugs included - 6mtr RED 10mm 2 cable - 0.5mtr BLACK 10mm 2 cable - 0.2mtr BLACK 1.5mm 2 cable assembly with M2 lug and 6.3mm fast on terminal - 2pcs M8 cable lug with insulation sleeve - 4pcs M6 cable lug with insulation sleeve - 4pcs cable tie 150mm : : R963 visit website for full spec and download on the Cyrix battery combinder Cyrix-i 24/48 V 400 A Cyrix-ct 12/24V-230A intelligent combiner The Cyrix Battery Combiner is a microprocessor controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a pre-set voltage (indicating that the battery is being charged), and disconnects when the voltage decreases below float level (indicating that one or more batteries are being discharged). Cyrix-Li-ct 12/ V system 24 V system Cyrix-ct 12/24V-400A intelligent combiner The Cyrix Battery Combiner is a microprocessor controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a pre-set voltage (indicating that the battery is being charged), and disconnects when the voltage decreases below float level (indicating that one or more batteries are being discharged). Cyrix-Li-ct 12/ V 24 V Continuous current and breaking capacity at 12 V or 24 V 230 A Continuous current and breaking capacity at 12 V or 24 V 400 A Breaking capacity at 48 V n. a. LED status indication Control cable Yes Included (length 1 meter) Cyrix-ct 12/24-230A R1 259 Cyrix-ct 12/24V-120A intelligent combiner The Cyrix Battery Combiner is a microprocessor controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a pre-set voltage (indicating that the battery is being charged), and disconnects when the voltage decreases below float level (indicating that one or more batteries are being discharged). Cyrix-Li-ct 12/ V system 24 V system Continuous current and breaking capacity at 12 V or 24 V 120 A Breaking capacity at 48 V n. a. LED status indication Control cable Yes Included (length 1 meter) Cyrix-ct 12/24v-120A Cyrix-ct 12/24v-120Akit R505 R1012 Breaking capacity at 48 V LED status indication Control cable n. a. Yes Included (length 1 meter) Cyrix-i 12/24V-400A R2 688 Cyrix-ct 24/48V-400A intelligent combiner The Cyrix Battery Combiner is a microprocessor controlled heavy duty relay that automatically connects batteries in parallel when one of them has reached a pre-set voltage (indicating that the battery is being charged), and disconnects when the voltage decreases below float level (indicating that one or more batteries are being discharged). Cyrix-Li-ct 12/ V 48V Continuous current and breaking capacity at 12 V or 24 V Breaking capacity at 48 V LED status indication Control cable 400 A n. a. Yes Included (length 1 meter) Cyrix-i 24/48v-400A R2688

43 Cyrix-Li-ct Battery combiner Cyrix-Li-ct 12/ Cyrix Battery Combiner Cyrix-Li-load 12/ Cyrix-Li-load 24/ Cyrix-Li-Charge 12/ Cyrix-Li-Charge 24/ V system Cyrix-Li-ct 12/ V system Continuous current and breaking capacity at 12V or 24V 120A 120A 120A Breaking capacity at 48V 40A 40A n. a. Control input The Cyrix engages when the control input is high (appr. ) The Cyrix disengages when the control input is left free floating or pulled low Connect voltage - 13,7V / 27,4V / 54,8V Disconnect voltage ,4V < V < 13,7V: 120 s 13,7V < V < 13,9V: 30 s V > 13,9V: 4 s 13,3V < V < 13,2V: 10 s V < 13,2V: immediate 26,8V < V < 27,4V: 120 s 27,4V < V < 27,8V: 30 s V > 27,8V: 4 s 26,6V < V < 26,4V: 10 s V < 26,4V: immediate R742 R742 R866 R866 R866 Cyrix Battery Combiner Cyrix-Li-load 12/ Cyrix-Li-load 24/ Cyrix-Li-Charge 12/ Cyrix-Li-Charge 24/ V system Cyrix-Li-ct 12/ V system Continuous current and breaking capacity at 12V or 24V 230 A 230 A 230 A Breaking capacity at 48V 80 A 80 A n. a. LED status indication Control cable Control input Yes Included (length 1 meter) The Cyrix engages when the control input is high (appr. ) The Cyrix disengages when the control input is left free floating or pulled low Connect voltage - 13,7 V / 27,4 V / 54,8 V 13,4V < V < 13,7V: 120 s 13,7V < V < 13,9V: 30 s V > 13,9V: 4 s 26,8V < V < 27,4V: 120 s 27,4V < V < 27,8V: 30 s V > 27,8V: 4 s Disconnect voltage ,3V < V < 13,2V: 10 s V < 13,2V: immediate 26,6V < V < 26,4V: 10 s V < 26,4V: immediate R1855 R1855 R1855 R1855 R1855 Battery Management System 12/200 A 12V BMS that protects the alternator (and wiring), and supplies up to 200A in any DC load (including inverters and inverter/chargers). BMS 12/200 specification Maximum number of 12,8V batteries 10 Maximum charge current, Power Port AB 40 C Maximum charge current, Power Port LB 40 C No load current when operating 10mA VE.Bus BMS R2721 The VE.Bus BMS protects each individual cell of a Victron lithium-iron-phosphate (LiFePO4 or LFP) battery. Each individual cell of a LiFePO4 battery must be protected against over voltage, under voltage and over temperature. Victron LiFePO4 batteries have integrated Balancing, Temperature and Voltage control (acronym: BTV) and connect to the VE.Bus BMS with two M8 circular connector cord sets. VE.Bus BMS Input voltage range Current draw, normal operation Current draw, low cell voltage 9 70V DC 10 ma (excluding Load Disconnect current) 2mA

44 Cables / Fuses and connectors Inverting remote on-off cable VE.Direct Cable : VE.Direct Cable : R225 VE.Direct Cable Non inverting remote on-off cable : : R225 VE.Bus BMS to BMS alternator control cable : : R393 Cables with M8 circular connector (for Li-ion batteries) M8 Connector Order Code Price Male to Female 3 pole 1 m (bag of 2) Male/Female3pole1m R393 Male to Female 3 pole 2 m (bag of 2) Male/Female3pole2m R416 Male to Female 3 pole 3 m (bag of 2) Male/Female3pole3m R449 Male to Female 3 pole 5 m (bag of 2) Male/Female3pole5m R505 Peak Power Pack The Peak Power Pack is a complete substitute for heavy lead acid batteries in applications where high currents occur for short time. Being primarily meant for caravan movers, it is equipped with a built in charger allowing charging from the car electrical system during the travel with the caravan. This way the pack will be fully charged upon arrival to the camping site. If necessary, the charging is possible using the supplied adapter via a grid outlet. Charging from a solar panel is also possible. Peak Power Pack PPP-8 PPP-20 PPP-30 PPP-40 Capacity 8Ah 20Ah 30Ah 40Ah Stored energy 102Wh 256Wh 384Wh 512Wh Battery type Lithium-ion (LiFePO4) Nominal voltage 12.8V Peak Power Pack 8Ah Peak Power Pack 20Ah Peak Power Pack 30Ah Peak Power Pack 40Ah R2619 R4205 R5823 R7285

45 SOLAR CABLES Solar Cable (4 mm²) with pre-assembled male and female MC4 (PVST01) connectors Solar Cable (4 mm²) M8 Connector Order Code Price Length 1 m R112 Length 3 m R168 Length 5 m R248 Solar adapter cable MC4 male to MC3 female, length 15 cm Solar Cable (6 mm²) M8 Connector Order Code Price Length 1 m R134 Length 3 m R203 Length 5 m R304 Length 10 m R462 Length 20 m R855 Solar adapter cable MC4 female to MC3 male, length 15 cm : Price on : R : Price on : Solar splitter pair MC4-Y, 1x M-2F / 1x F-2M Solar connector pair MC4, 1x Male / 1x Female : Price on : : : Accessories for the Blue Power IP65 Charger Accessories for the Blue Power IP65 Charger M6 eyelet connector (with 30A ATO fuse) M6 eyelet connector R67 M8 eyelet connector (with 30A ATO fuse) 0 R67 2 meter extension cable 2 Meter ext cable R90 12 Volt plug (cigarette plug with 16A fuse) R147 Clamp connector (with 30A ATO fuse) Clamp connector R134 Battery indicator panel (M8 eyelet connector/30a ATO) 0 R236 Battery indicator panel (M8 eyelet / 30A ATO Fuse) 0 R147 Rubber bumber for IP65 Charger 12/10, 12/15, 24/8 R67 Wall Mount for IP65 Charger 12/10,12/15,24/8 R56 visit website for full spec and download on the accessories BluePower IP65 ACCESSORIES Clamp connector (with 30A ATO fuse) Order Code Price Clamp connector R134.00

46 Fuses FUSE PRICE MIDI-fuse 60A/32V (package of 5 pcs) R134 MIDI-fuse 80A/32V (package of 5 pcs) R134 MIDI-fuse 100A/32V (package of 5 pcs) R134 MIDI-fuse 150A/32V (package of 5 pcs) R134 MIDI-fuse 200A/32V (package of 5 pcs) R134 MIDI-fuse 30A/58V (package of 5 pcs) R123 MIDI-fuse 40A/58V (package of 5 pcs) R123 MIDI-fuse 50A/58V (package of 5 pcs) R123 MIDI-fuse 60A/58V for 48V products (1 pc) R123 MIDI-fuse 80A/58V (package of 5 pcs) R123 MIDI-fuse 100A/58V for 48V products (1 pc) R123 Fuse holder for MIDI-fuse R101 MEGA-fuse 60A/32V (package of 5 pcs) R168 MEGA-fuse 80A/32V (package of 5 pcs) R168 MEGA-fuse 100A/32V (package of 5 pcs) R168 MEGA-fuse 125A/32V (package of 5 pcs) R168 MEGA-fuse 150A/32V (package of 5 pcs) R168 MEGA-fuse 175A/32V (package of 5 pcs) R168 MEGA-fuse 200A/32V (package of 5 pcs) R168 MEGA-fuse 225A/32V (package of 5 pcs) R168 MEGA-fuse 250A/32V (package of 5 pcs) R168 MEGA-fuse 300A/32V (package of 5 pcs) R168 MEGA-fuse 400A/32V (package of 5 pcs) R270 MEGA-fuse 500A/32V (package of 5 pcs) R281 MEGA-fuse 125A/58V for 48V products (1 pc) R337 MEGA-fuse 200A/58V for 48V products (1 pc) R337 MEGA-fuse 250A/58V for 48V products (1 pc) R337 MEGA-fuse 300A/58V for 48V products (1 pc) R337 Fuse holder for MEGA-fuse R134 Modular fuse holder for Mega-fuse R404 Busbar to connect 5 CIP (500 A) R438 Busbar to connect 6 CIP (1500 A) R505 ANL-fuse 400A/80V for 48V products (1 pc) R112 ANL-fuse 500A/80V for 48V products (1 pc) R112 Fuse holder for ANL-fuse R112 Fuse 125A/170Vdc Fuse CNN 325A/80V for Lynx shunt R618 R630

47 Color Control GX Panels and system monitoring The Color Control GX is the communication-centre of your installation. It offers at-a-glance live information, and lets you control all products connected to it. Full system control is gained - almost anywhere in the world - by accessing your Color Control GX using our free-to-use Victron Remote Management Portal : COLOUR CONTROL GX : R5 914 The Venus GX is the communication-centre of your installation. Venus allows you to talk to all components in your system and ensure they are working in harmony. Monitoring of live data, and changing settings is performed by using your smartphone (or other device) via our free-to-use Victron Remote Management Portal (VRM). Venus GX : VENUS GX : R3373

48 Temperature sensor VENUS/ PMP/Quattro Victron Energy temperature sensor for Venux GX, Phoenix MultiPlus and Quattro : : R281 CCGX WiFi module simple Victron Energy CCGX WiFi module simple (Nano USB) : : R259 CCGX WiFi module long range Victron Energy CCGX WiFi module simple (Nano USB) : CCGX WIFI LONG RANGE : R900 Anti-islanding relay UFR The UFR1001E monitors voltage and frequency in plants for own generation of electricity. : Anti-island relayufr : R5625 VE.Net Panel VE.Net VE.Net GMDSS Panel The Order Venus number: GX is the VE.Net communication-centre Panel of your installation. Venus allows you to talk to all components in your system and ensure they are working in harmony. Price excluding Monitoring VAT: of live R2293 data, and changing settings is performed by using your smartphone (or other device) via our free-to-use Victron Remote Management Portal VE.Net Blue Power Panel 2 : VE.Net GMDSS Panel : R2 293 VE.Net Blue Power Control GX : VE.NetBluePowPanel2 : R3 316 : VE.NetBluePowPanelGX : R3 507

49 VE.Net Battery Controller (VBC) 12/24/48V VE.Net Battery Controller V : VE.NetBatCon(VBC) : VE.Net BatCon70-350V : R2586 : Price on Shunt 500A/50mV Shunt 1000A/50mV : Shunt 500A/50mV : Shunt 1000A/50mV : R683 : R1 226 Shunt 2000A/50mV Shunt 6000A/50mV : Shunt 2000A/50mV : Shunt 6000A/50mV : R2419 : R3 373 VE.Net Tank Monitor (Current) VE.Net Tank Monitor (Resistive) : VE.Net Tank Mon(Cur) : R2462 : VE.Net Tank Mon(Res) : R2462 VE.Net Tank Monitor (Voltage) VE.Can resistive tank sender adapter : VE.Net Tank Mon(Vol) : R2462 : : R4396

50 Digital Multi Control 200/200A Digital Multi Control 200/200A GX : DigitalMultiControl : DigitalMultiConGX : R1 686 : R1718 Phoenix Inverter Control Phoenix Charger Control : Phoenix Inverter Con : PhoenixCharControl : R956 : R1012 Phoenix Inverter Control VE.Direct Skylla-i Control GX : PhoenixInvCont VE.D : : R281 : Charger Switch Skylla Control : Charger Switch : Skylla Control : R1 237 : R1686 Battery Alarm GX Victron Global Remote 2 (VGR-2)* : Battery Alarm GX : VictronGlobalRemote2 : R788 : R4206

51 Victron Ethernet Remote** Global Remote to BMV-60XS conn. kit : Vic Ethernet Remote : BMV-60XS CON KIT : R6469 : R1202 VE.Direct LoRaWAN EU module VE.Direct LoRaWAN US module : : R1012 : : R1012 VE.Direct LoRaWAN AU module Outdoor antenna 4dBi for VGR with 5 meter cable : : R1012 : Outdoor Antenna 4dBi : R2379

52 Wall mount enclosure for 65 x 120 mm GX-panels with 90 degr. RJ45 socket only: - BPA R - Battery Alarm GX - REC R - Skylla-i Control GX (90º RJ45) - DMC R - Digital Multi Control 200/200A GX (90º RJ45) VGR I/O Extender : VGR I/O Extender : Wall M/E GX-Panels : 3211 : R Wall mount enclosure for Color Control GX Wall mount enclosure for BMV or MPPT Control : Wall M/E for C C : Wall M/E BMV : R : R304 Wall mount enclosure for Color Control GX USB extension cable 0.3m one side right angle : Wall M/E CC & BMV : : R562 : R90

53 DATA CABLES and INTERFACES Network cables for ESP System and BMV-600 and BMV-700 Cable Order Number Price excuding VAT RJ12 UTP Cable 0,3 m RJ12 UTP CABLE 0.3M* R90 RJ12 UTP Cable 0,9 m RJ12 UTP CABLE 0.9M* R90 RJ12 UTP Cable 1,8 m RJ12 UTP CABLE 1.8M* R90 RJ12 UTP Cable 3 m RJ12 UTP CABLE 3M* R112 RJ12 UTP Cable 5 m RJ12 UTP CABLE 5M* R134 RJ12 UTP Cable 10 m RJ12 UTP CABLE 10M* R168 RJ12 UTP Cable 15 m RJ12 UTP CABLE 15M* R203 RJ12 UTP Cable 25 m RJ12 UTP CABLE 25M* Price on RJ12 UTP Cable 30 m RJ12 UTP CABLE 30M* R337 Network cables for VE.Can, VE.Bus, VE.Net and VE9bitRS485 Cable Order Number Price excuding VAT RJ45 UTP Cable 0,3 m RJ45UTPCABLE 0.3M** R90 RJ45 UTP Cable 0,9 m RJ45UTPCABLE0.9M** R90 RJ45 UTP Cable 1,8 m RJ45UTPCABLE1.8M** R112 RJ45 UTP Cable 3 m RJ45UTPCABLE3M** R134 RJ45 UTP Cable 5 m RJ45UTPCABLE5M** R168 RJ45 UTP Cable 10 m RJ45UTPCABLE10M** R203 RJ45 UTP Cable 15 m RJ45UTPCABLE15M** R281 RJ45 UTP Cable 20 m RJ45UTPCABLE20M** R337 RJ45 UTP Cable 25 m RJ45UTPCABLE25M** R360 RJ45 UTP Cable 30 m RJ45UTPCABLE30M** R393 VE.Direct cables, use to connect BMV-70x and low power MPPTs to the Color Control GX Cable Order Number Price excuding VAT VE.Direct Cable 0,3m R168 VE.Direct Cable 0,9m R168 VE.Direct Cable 1,8m VE.Direct Cable 1.8m R168 VE.Direct Cable 3m R192 VE.Direct Cable 5m VE.Direct Cable 5m R214 VE.Direct Cable 10m VE.Direct Cable 10M R259 VE.Direct Cable 0,3m (one side Right Angle conn) VE.Direct Cable 0,9m (one side Right Angle conn) VE.Direct Cable 1,8m (one side Right Angle conn) VE.Direct Cable 3m (one side Right Angle conn) VE.Direct Cable 5m (one side Right Angle conn) VE.Direct Cable 10m (one side Right Angle conn) R168 R168 R168 R192 R214 R259

54 VE.Direct to BMV60xS Cables, use to connect BMV-60xS to the Color Control GX graphical user interface Cable Order Number Price excuding VAT VE.Direct to BMV60xS Cable 0,3m VE.Direct to BMV60xS Cable 0,9m VE.Direct to BMV60xS Cable 1,5m VE.Direct to BMV60xS Price on Price on R290 VE.Direct to BMV60xS Cable 3m Price on Cables with M8 circular connector (for 12.8V Li-ion batteries) Cable Order Number Price excuding VAT Male to Female 3 pole 1 m (bag of 2) Male to Female 3 pole 2 m (bag of 2) Male to Female 3 pole 3 m (bag of 2) Male to Female 3 pole 5 m (bag of 2) Male/Female3pole1m Male/Female3pole2m Male/Female3pole3m Male/Female3pole5m R393 R416 R449 Price on Interfaces to connect Victron products to your computer Cable Order Number Price excuding VAT VE.Direct to USB interface VE.Direct to USB R326 Interface MK2-USB (VE.Bus to USB) Interface MK3-USB (VE.Bus to USB) MK2-USB MK3-USB R844 R788 CANUSB interface CANUSB Interface R5 577 Interfaces to connect Victron products to NMEA2000 Cable Order Number Price excuding VAT VE.Bus to NMEA2000 interface VE.BustoNMEA2000int R3 639 VE.Direct to NMEA2000 interface VE.DirecttoNMEA2000 R2 462 VE.Can to NMEA2000 Micro-C male VE.CantoNMEA2000 R1 125 BMV-60xS to NMEA2000 interface R- BMV-60xS to VE.Can interface R-

55 Interfaces for industrial use / datacommunication Cable Order Number Price excuding VAT Interface MK2.2b (VE.Bus to RS232) MK2.2B ASS R652 RS232 to USB converter R348 VE.Direct to RS232 interface VE.Bus tors232 Intf. R326 Interfaces to connect Victron products to each other Miscellaneous Cable VE.Direct to VE.Can interface R3 284 VE.Direct to Global Remote interface R900 VE.Can RJ45 terminator (bag of 2) R134 ASS : BMV Data Link RS232 with software Price excuding VAT R713 VE.Bus to VE.Can interface R2 248 Inverting remote on-off cable R225 Non-inverting remote on-off cable R225 VE.Direct non inverting remote on-off cable VE.Bus BMS to BMS alternator R225 R393 control cable Skylla-i remote on-off cable R393 VE.Net to VE.Bus Converter R2 293 Miscellaneous Order Number Price excuding VAT VE.Can Power Cable Price on Interface 1140 INTERFACE 1140 R3284 AC Current sensor AC Current Sensor R562 Wireless AC sensor, single phase Wireless AC Sensor R2 055 Wireless sensor gateway Wireless Sensor G/W R3 222 VE.Direct Bluetooth Smart dongle Cable Order Number Price excuding VAT VE.Direct Bluetooth Smart dongle VE.DirectBluetooth R562 VE.Bus Smart dongle R900 Ziehl anti-islanding relays Cable Order Number Price excuding VAT Anti-islanding relay UFR1001E Anti-island relayufr R5625 Anti-islanding relay SPI1021 Price on

56 SHORE CABLES: Shore Power Cords with Shore Power Organiser Bag Cable Order Number Price excuding VAT Shore Power Cord 15m 16A ShorePowCord 15M 16A R1 686 Shore Power Cord 25m 16A ShorePowCord 25m 16A R2 293 Shore Power Cord 15m 25A ShorePowCord 15M 25A R2 170 Shore Power Cord 25m 25A ShorePowCord 25M 25A R- Shore Power Cord 25m 32A ShorePowCord 25m 32A R4 238 Cable Order Number Price excuding VAT Power Inlet 16A polyamid wth cover Power Inlet 16A stainless steel with cover Power Inlet 16A poly Power Inlet 16A R652 R944 Power Inlet 32A stainless steel with cover Power Inlet 32A R1 248 Plug 16A/250Vac (2p/3w) for Power Inlet 16A PLUG 16A/250VAC R753 Plug 32A/250Vac (2p/3w) for Power Inlet 32A PLUG 32A /250VAC R1 023 Cable Order Number Price excuding VAT Adapter Cord 16A/250V Schuko/CEE R236 Adapter Cord 16A/250V CEE/Schuko R225 Splitter Cord 16A/250V CEE/2xCEE SPLITCORD16A/250VCEE R764 Adapter Cord 16A to 32A/250V CEE/CEE R337 Adapter Cord 32A 3 phase to single phase R462 12V AND 24V INVERTERS: ALTERNATIVE OUTLETS Outlet Price Phoenix 12/180 IEC outlet Phoenix12/180 IECout R- Phoenix 12/180 Schuko outlet Phoenix 12/180 AU/NZ outlet (AS/NZS 3112 ) R- Phoenix 12/180 UK outlet (BS 1363) R- Phoenix 12/250 VE.Direct IEC R1 079 Phoenix 12/250 VE.Direct Schuko Phoenix 12/250 VE.Direct AU/NZ (AS/NZS 3112 ) R1 079 Phoenix 12/250 VE.Direct UK (BS 1363) R1 079 Phoenix 12/350 IEC outlet Phoenix12/350 IECout R821 Phoenix 12/350 Schuko outlet R- Phoenix 12/350 AU/NZ outlet (AS/NZS 3112 ) R- Phoenix 12/350 UK outlet (BS 1363) R- Phoenix 12/375 VE.Direct IEC R1 395 Phoenix 12/375 VE.Direct Schuko R- Phoenix 12/375 VE.Direct AU/NZ (AS/NZS 3112 ) R1 395 Phoenix 12/375 VE.Direct UK (BS 1363) R1 395 Phoenix 12/800 IEC outlet R3 148 Phoenix 12/800 Schuko outlet R- Phoenix 12/800 AU/NZ outlet (AS/NZS 3112 ) R3 148 Phoenix 12/800 UK outlet (BS 1363) R3 148 Phoenix 12/1200 IEC outlet R4 610 Phoenix 12/1200 Schuko outlet R- Phoenix 12/1200 AU/NZ outlet (AS/NZS 3112 ) R4 610 Phoenix 12/1200 UK outlet (BS 1363) R4 610 Phoenix 24/180 IEC outlet Phoenix24/180 IECout R562

57 Phoenix 24/180 Schuko outlet R- Phoenix 24/180 AU/NZ outlet (AS/NZS 3112 ) R- Phoenix 24/180 UK outlet (BS 1363) R- Phoenix 24/250 VE.Direct IEC R1 079 Phoenix 24/250 VE.Direct Schuko R- Phoenix 24/250 VE.Direct AU/NZ (AS/NZS 3112 ) R1 079 Phoenix 24/250 VE.Direct UK (BS 1363) R1 079 Phoenix 24/350 IEC outlet Phoenix24/350 IECout R- Phoenix 24/350 Schuko outlet R- Phoenix 24/350 AU/NZ outlet (AS/NZS 3112 ) R- Phoenix 24/350 UK outlet (BS 1363) R- Phoenix 24/375 VE.Direct IEC R1 395 Phoenix 24/375 VE.Direct Schuko R- Phoenix 24/375 VE.Direct AU/NZ (AS/NZS 3112 ) R1 395 Phoenix 24/375 VE.Direct UK (BS 1363) R1 395 Phoenix 24/800 IEC outlet R3 148 Phoenix 24/800 Schuko outlet R- Phoenix 24/800 AU/NZ outlet (AS/NZS 3112 ) R3 148 Phoenix 24/800 UK outlet (BS 1363) R3 148 Phoenix 24/1200 IEC outlet R4 610 Phoenix 24/1200 Schuko outlet R- Phoenix 24/1200 AU/NZ outlet (AS/NZS 3112 ) R4 610 Phoenix 24/1200 UK outlet (BS 1363) R4 610 Phoenix 48/250 VE.Direct IEC Phoenix48/250 IEC R1 259 Phoenix 48/250 VE.Direct Schuko R- Phoenix 48/250 VE.Direct AU/NZ (AS/NZS 3112 ) R1 259 Phoenix 48/250 VE.Direct UK (BS 1363) R1 259 Phoenix 48/350 IEC outlet R- Phoenix 48/375 VE.Direct IEC R1 574 Phoenix 48/375 VE.Direct Schuko R- Phoenix 48/375 VE.Direct AU/NZ (AS/NZS 3112 ) R1 574 Phoenix 48/375 VE.Direct UK (BS 1363) R1 574 Phoenix 48/800 IEC outlet R3 373 Phoenix 48/1200 IEC outlet Phoenix48/1200 IEC R4 947

58 Cable Order Number Price excuding VAT Wired AC sensor HUB-4 1/3-phase Imax=65A Energy meter ET112-1 phase - max 100A Wired AC sensor HUB4 EnergyMeter 1Phase Price on R855 Energy meter ET340-3 phase - max 65A/phase Energy meter EM24-3 phase - max 65A/phase EnergyMeter 3Phase R1 686 Price on RS485 to USB interface cable 1,8 m RS485 to USB 1.8m R315 RS485 to USB interface cable 5 m RS485 to USB 5m R360 Zigbee to RS485 converter Zigbee to RS485 R1 293 Zigbee to USB converter Zigbee to USB R1 125 Anti-islanding box 63A single phase - UK Anti-islanding box 63A single and three phase R R The VRM app Monitor and manage your Victron Energy system. Login with your VRM account, and see all your sites in a list. Tap a site to see its system diagram, current system status and energy flow. Contact us JHB: Tel: / Tel: , Fax: KZN (Durban) : Tel: , Fax: CPT (CapeTown): Tel: , Fax: Mbombela: Tel: , Fax: Tshwane: Tel: , Fax: Terms and Conditions 1. Pricelist replaces and render invalid all previous prices 2. Pricing applies to current exchange rate levels. Fluctuations may result in re-pricing 3. Pricing as indicated is net and excludes VAT 4. The content of this document is monitored in an ongoing manner and updated when necessary. Discrepancies may still arise and are subject to changes and errors. No guarantee is made for the completeness of these document. The information and descriptions are non-binding and are solely for informational purposes. 5. Project specific pricing and larger order quantities available on 6. Standard payment and delivery terms apply