SERVICE MANUAL SUPPLEMENT

Transcription

1 21-63H-01 PB-770H, PB-770T 1 SERVICE MANUAL SUPPLEMENT 2 ECHO: PB-770H ECHO: PB-770T INTRODUCTION We are constantly working on technical improvement of our products. For this reason, technical data, equipment and design are subject to change without notice. All specifications and directions in this SERVICE DATA are based on the latest product information available at the time of publication. POWER BLOWER (Serial number : ) (Serial number : ) (Serial number : ) (Serial number : ) (Serial number : ) (Serial number : ) CONTENTS page 1 SERVICE INFORMATION Specification Technical data Torque limits Special repairing materials Service limits Special tools CARBURETOR ADJUSTMENT PROCEDURE General adjusting rules Complete adjustment... 7 Reference No H-01 REVISED: ISSUED:

2 2 SERVICE INFORMATION PB-770T/H 1 SERVICE INFORMATION 1-1 Specifications Model PB-770T PB-770H Dimensions Length* mm(in) 375 (14.8) Width* mm(in) 490 (19.3) 535 (21.1) Height* mm(in) 475 (18.7) Dry weight** kg(lb) 10.8 (23.7) 11.0 (24.2) Engine Type YAMABIKO, air-cooled, two-stroke, single cylinder Rotation Counterclockwise as viewed from the output end Displacement cm 3 (in 3 ) 63.3 (3.86) Bore mm(in) 48.0 (1.89) Stroke mm(in) 35.0 (1.38) Compression ratio 6.5 Carburetor Type Rotatry type : Diaphragm, horizontal-draft, with purge bulb Model Walbro WYK-345 with Small D-shaped mixture needle Ignition Type CDI (Capacitor discharge ignition) Spark plug Variable Slope Timing (VST) : Slope advance ignition combined with electronic speed governor BPM8Y (CANADA : BPMR8Y) Exhaust Muffler type Spark arrester muffler with catalyst Starter Type Automatic rewind Rope diameter x length mm(in) 3.5 x 1000 (0.14 x 39.37) Fuel Type Premixed two-stroke fuel Mixture ratio 50 : 1 (2 %) Gasoline Two-stroke air cooled engine oil Minimum 89 octane unleaded ISO-L-EGD (ISO/CD13738), JASO M345-FC/FD Tank capacity L (U.S.fl.oz.) 2.02 (68.3) Throttle Mount Tube-mounted throttle Hip-mounted throttle with cruise control with cruise control Blower Fan type Closed fan ID : Inner diameter. Max. air volume (with pipes) Max. air velocity (with pipes) m 3 /min (ft 3 /min) 21.7 (765)*** m/s (mph) 91.1 (204)*** Discharge ID mm (in) 72 (2.83)*** * Without flexible pipe and blower pipes. ** With flexible pipe and blower pipes. *** With taper pipe.

3 PB-770T/H SERVICE INFORMATION Technical data Model PB-770T PB-770H Engine Idling speed RPM 2,500 +/- 200 Wide open throttle speed RPM 6,600-6,800 Compression pressure MPa (kgf/cm 2 ) (psi) 1.01 (10.3) (146) Ignition Spark plug gap mm(in) ( ) Minimum secondary voltage at 1,500 RPM kv 22 Primary coil resistance Ω Secondary coil resistance kω Pole shoe air gaps mm(in) ( ) Ignition timing at 3,000 RPM BTDC 25 at 8,000 RPM BTDC 31 at 11,000 RPM BTDC 21 PET-9000 Parameter Parameter 2 05 Carburetor Venturi size mm(in) 15.0 (0.591) Throttle bore mm(in) 15.0 (0.591) Idle adjust screw initial setting turn in* 5/8 Test Pressure, minimum MPa (kgf/cm 2 ) (psi) 0.05 (0.5) (7.0) Metering lever height mm (in) 1.5 (0.06) lower than diaphragm seat BTDC: Before top dead center. * Set idle adjust screw to the point that its tip just contacts throttle plate before initial setting. ** Screw in idle mixture needle from initial thread engagement (at the point that the clicking sound is heard). 1-3 Torque limits Descriptions Size kgf cm N m in lbf Starter Ignition Fuel Starter pawl assembly M Starter case M 5* Flywheel M C.D.I module M Spark plug M Carburetor M Intake bellows M Fuel tank M 5* Engine Crankcase M Cylinder M Engine plate M Engine mount M 6* Cylinder cover M 5* Engine cover Crankcase side M 5* Fan case side M Cleaner case side M

4 4 SERVICE INFORMATION PB-770T/H 1-3 Torque limits (Continued) Descriptions Size kgf cm N m in lbf Engine Dust cover M 5* lead M Muffler M Muffler stay M Exhaust guide M Others Fan case Blower grid side M Blower fan M Backpack harness M Backpack frame M Backpack stopper M Cleaner case M Trigger bracket fixture M Throttle lever M lead M Regular bolt, nut and screw M M M M M * Apply thread locking sealant (See below) 1-4 Special repairing materials Material Location Remarks Grease Rewind spring Starter center post Lithium based grease or ECHO XTended Protection TM Lubricant Oil seal inner lips Thread locking sealant Engine mount Loctite #675 or equivalent Cylinder cover Dust cover Engine cover (Crankcase side) Starter case Fuel tank Loctite #242, ThreeBond #1324 or equivalent Loctite #222, ThreeBond #1342 or equivalent

5 PB-770T/H 1-5 Service limits SERVICE INFORMATION 5 A B C D 5K247 5K248 5K249 5K250 E F G H 5K251 5K016 5K042 5K252 K L 5K219 5K220 Description mm (in) A Cylinder bore When plating is worn and aluminum can be seen B Piston outer diameter Min (1.885) C Piston pin bore Max (0.3951) D Piston ring groove, 1st Max (0.065) 2nd Max (0.063) E Piston ring side clearance Max (0.004) F Piston pin outer diameter Min (0.3929) G Piston ring width Min (0.057) H Piston ring end gap Max (0.02) K Con-rod small end bore Max (0.5522) L Crankshaft runout Max (0.001)