Synthetic Gear Oil Performance Comparison

Transcription

1 Synthetic Gear Oil Performance Comparison Gearbox Failure Source Gears and Bearings Wear Out or Seize Rust and Corrosion Thermal Breakdown Pump Cavitation, Dry Areas Oil Deposit Build-up Thickening in Cold Temperature Gear Oil Property Extreme Pressure and Wear Protection Corrosion Protection Temperature Resistance Foaming Tendency Oxidation Resistance Low Temp. Flow and Pumpability Gear Oil Test Methods, Descriptions, Test Result Values and What They Mean ASTM D 3233: Falex Load Test Measures extreme pressure properties (in pounds) of a fluid lubricant using the falex pin method. Greater amount equals greater extreme pressure characteristics. ASTM D 2783: Film Strength Uses 4-ball method to determine load-carrying properties of lubricating fluid. The higher number the better protection. ASTM D 2783: Weld Point Measures the lowest applied load in kilograms at which the rotating ball welds to the three stationary balls. The higher the number the better extreme pressure characteristics. ASTM D 2783: Load Wear Index An index of the ability of a lubricant to minimize wear at applied loads. The higher the number the better the wear protection. ASTM D 2782: Timken Method Line contact, similar to roller bearing, the higher the number the greater load carrying capabilities. ASTM D 4172: Four-ball (wear scar) Measures the relative wear preventive properties of lubricating fluids in sliding contact, using the 4-ball method. The lower the number the more protection the oil provides. ASTM D 130: Copper Corrosion Measures ability to protect yellow metals from corrosion.the range is 1A being the best rating and 4 being worst, 1B is typical. ASTM D 2070: Thermal Stability Test Measures thermal stability of oil. Also measures viscosity increase and insolubles recorded. The lower percent the better. ASTM D 892: Foam Test Measures the amount of foam produced at specified temperatures and different air blowing intervals. No foam is best. ASTM D 189: Conradson Carbon Residue Measures the residue formed by evaporation and thermal degradation of the oil. The less percentage of carbon residue the better. FTM 3456: Channel Point When a gear passes through the gear oil, the oil flows in behind it filling in the channel left by the gear. This method records the temperature at which the gear oil no longer flows back into the channel. ASTM D 97: Pour Point The lowest temperature at which movement of the fluid is observed is recorded as the pour point. The lower the pour point, the better utility the fluid has for certain applications at low temperature. Mobil SHC ISO Grade Gear Oil Not Published Not Published Synthetic Certop Industrial ISO Grade Gear Oil 2250 lb 23,000 psi 250 kg 400 kg lb 90 lb Not Published 1B 0.50 mm 1A Not Published Less than 1% 0/0/0 40/37/0 Not Published 1% Not Published -45 to -27 C -20 F Less than -40 to -27 C

2 Spectra Xtreme CJ-4 Advanced Performance Synthetic Blend Motor Oil SAE 15W-40 Synthetic blend, multi-grade Diesel or Gasoline motor oil formulated for severe duty and extended drain intervals Provides superior protection against deposit formation, oil breakdown, parts wear, and loss of compression. Specifically Engineered for Construction Agriculture Trucking & Fleet Logging Waste Hauling Material Handling Equipment Marine Federal, State, and Local Agencies Other Industries that Utilize Heavy Equipment Synthetic Blend Formula Engineered for Extended Drain Intervals* TBN of 13 Provides Extended Acid Neutralization While Maintaining Low Ash Excellent Performance with EGR, ACERT, ASET and Turbo Charged Equipment Superior Thermal Stability for Higher Temperature Operation High Detergent Retention Prevents Deposit Build-up Contains SOLUMOL** for Superior Wear Protection Highly Resistant to Oxidation for Longer Oil Life High V.I. Number Provides Stable Viscosity Over a Wide Temperature Range Superior Cold Cranking and Oil Pumpability at Low Temperature Compatible with Synthetic, Synthetic Blend, and Mineral Based Motor Oils * Always use oil analysis to establish new drain intervals ** SOLUMOL is an oil soluble synthetic molybdenum compound Irving, Texas Indianapolis, Indiana Kendall Park, New Jersey Sunnyvale, California NCH Corporation Consult the label for complete directions and precautions before using this product. For Peak Performance, use with LubeMaster System Purge Meets or Exceeds the Following Performance Requirements API Service Classification: CJ-4 CI-4, CI-4 Plus, CH-4 Plus, CH-4, and SM for gasoline engines ACEA E&-04 (2004) MIL-PRF-2104G, CID-A-A-52306A, and CID-A-A-52039B Mack EO-O Premium Plus 07 MTU Type 2 MAN 3275 Caterpillar ECF-1-A, ECF-2, ECF-3 Cummins CES Renault RVI RLD-3 Daimler Chrysler MB228.31, MB228.3 Detroit Diesel DDC 93K218 Volvo VDS-4 Division of Certified Laboratories

3 SPECTRA XTREME Motor Oils contain a total additive package that sets it apart from all other motor oils Additives Premium, Synthetic Blend Base Oil Acid Neutralizers Friction Reducers Anti-Wear Agents Shear Stabilizers Dispersants Detergents Oxidation Inhibitors Corrosion Inhibitors Rust Inhibitors Viscosity Index Improvers Pour Point Depressants Solumol Benefits Highly-refined, oxidation-resistant synthetic blend base oils provide excptional, long-term lubrication to reduce friction, decrease heat and prevent wear. SPECTRA XTREME prevents the formation of various acids and sludge. SPECTRA XTREME outlasts conventional oils by up to 300% due to it's high residual TBN. Plate out on metal surfaces to prevent friction and wear under heavy loads. Prevents dry starts. Form a lubricant film on metal surfaces in the presence of heavy loads and high temperatures. Prevents cold welding. Increase surface viscosity and improve shear stability to carry heavier loads, withstand extreme pressures and prevent shock impact. Keep sludge, carbon, soot, varnish and gum suspended in the oil and carry them to the filter. Prevent deposits on high-contact surfaces. Keep surfaces clean and free of deposits that cause wear and increase blow-by. Extend service life of the lubricant by retarding the oxidation or breakdown process. Shield sensitive metals against acids and other corrosive compounds. Plate metal surfaces to retard metal deterioration and reduce abrasive rust contaminants. Maintain full viscosity over a wider temperature range to ensure full protection in fluctuating conditions. Eliminates the need to switch oil grades in different seasons. Keep oil flowing properly in cold temperature. Lowers frictional drag and keeps equipment running in cold temperatures. An oil soluble synthetic molybdenum compound that plates onto the metal to provide exceptional wear protection. Physical Properties TEST 15W-40 Specific Gravity (API) 29.7 Viscosity, CCS C, Max 6200 Viscosity SUS 40 C C 14.1 Viscosity Index 134 Flash Point ( F) 440 Pour Point ( F) -17 ASTM D130 Corrosion 1A Foam Suppression Sequence I 0 Sequence II 0 Sequence III 0 Sulphated Ash, % 1 TBN 13 IDEAL FOR USE: Compatible with gasoline or diesel engines or combustion engines which have been converted to natural gas. DO NOT USE: Not compatible with 2-cycle gasoline engines that mix oil with fuel.

4 Value Recognition Report A Trucking Company with 24 Trucks Account History: The US based company runs aggregate haul trucks, averaging 10,000 miles per oil change. In order to reduce operating expenses, an initiative to extend engine oil drain intervals was established. The company examined their Shell Rotella Oil, an engine oil from DA lubricants and Certified Labs engine oil. Samples were periodically pulled and sent to Staveley Services for analysis. Reduced Lubricant Consumption Increased Change Intervals Size of fleet: 24 trucks (5 dump trucks and 19 tractor trailers) Annual miles traveled 3,120,000 for the fleet (130,000 average annually) Amount of Oil per Change: 10.5gls Filter Costs: $30.00/truck, Labor Costs: $40.00 Engine Oil Costs Shell Rotella: $11.00/gl, $ total oil cost Strata Xtreme CJ4: $21.95/gl, $ total oil cost Oil Change Intervals and Cost per Change Shell Rotella 10,000 mile: $185.5 (13 changes) Strata Xtreme 40,000 mile: $300.5 (3.25 changes) Total Cost per Truck Annually (Cost x Number of Changes) = Total Shell Rotella: $2, ($58,140 for fleet) Strata Xtreme: $ ($23,439 for) Savings using Strata Xtreme: $34,701 M i l e s B e t w e e n O i l C h a n g e s 45,000 40,000 35,000 30,000 25,000 20,000 15,000 10,000 5,000 0 Engine Oil Longevity Case Study Shell Rotella Oil DA Lubricants Certified Labs Staveley Service oil analysis lab was used to determine the appropriate change intervals. Spectrographic Analysis, physical properties and contamination tests were performed on the oil samples. The Certified Labs STRATA XTREME engine oil provides exceptional wear protection, kept within the appropriate viscosity range and was able to continue to neutralize acid well into the 38,000 mile range. It was safely determined that STRATA XTREME could safely be used to extend drain intervals twice as long as the DA Lubricant oil and four times longer than the Shell Rotella oil bought from a distributor. Projected Annual Savings from Extended Engine Oil Drain Intervals and Reduced Components Replacements = $34, Additional Savings Will Increase Through a Reduction of Engine Parts Replacement, Labor Costs and Downtime. Irving, Texas Indianapolis, Indiana Kendall Park, New Jersey Sacramento, California NCH Corporation Division of Certified Laboratories

5 Comparison of CJ-4 Engine Oils Engine Oil Test Methods, Descriptions, Test Result Values and What They Mean Engine Oil Property Amsoil CJ-4 Shell Rotella T Mobil Delvac Elite Schaeffer Supreme 7000 Chevron Ursa Plus EC Royal Purple CJ-4 Castrol Hypuron 15W-40 Certified Labs Spectra Xtreme CJ-4 Performance Benefit ASTM D 3945: Shear Stability Index Measures the percent viscosity loss at 100 C of polymer-containing fluids when evaluated by using the Fuel Injector Shear Stability Test (FISST). The less viscosity loss the better protection and lubrication. 4.2% 9.9% <3% Loss ASTM D 2270: Viscosity Index Measures variation in viscosity due to changes in temperature. The higher the number, the more stable the oil will be at varying temperatures and conditions. ASTM D 2602: Viscosity by Cold Cranking Simulator Measures the apparent viscosity of the oil at cold temperatures. The results are related to the cranking characteristics of the oil. The lower viscosity reading the easier the oil will flow at low temperatures. ASTM D 4683: High Shear/High Temperature Viscosity at the shear rate and temperature of this test method is the condition encountered in the bearings of automotive engines in severe service. Should have a minimum viscosity of 3.5 cp according to SAE. ASTM D 3829: Borderline Pumping Temperature of Engine Oil Measures the lowest temperature at which engine oil can be continuously and adequately supplied to the oil pump inlet of an automotive engine. In this case, measures viscosity at 20 C. FTM 203C: Stable Pour Point Measures the lowest temperature at which movement of the fluid is observed. The lower the pour point, the better utility the fluid has for certain applications at low temperatures. ASTM D 2896: Total Base Number (TBN) Measures the engine oil s ability to neutralize acid formation, which commonly occurs. The highest TBN for engine oil is 14. The higher the TBN, the more acid will be neutralized and the longer the oil will last. ASTM D 5158: Phosphorous/Zinc Content Measures the amount of additive elements, wear metals and contaminants in lubricating oils. Phosphorous and zinc are part of the anti-wear package. The greater the concentration in ppm s of each in the oil the better the oil will protect various engine components. ASTM D 874: Sulfated Ash Content Measures the amount of sulfated ash from unused lubricating oils containing additives. The less amount of sulfated ash the better. Engine Oil Thermal Performance and Operating Viscosity Engine Oil Anti-wear and Contamination Control Performance Ave cp 4.2cp 5,460cp 4.3cp 3250cp -20 F - 20 F - 20 F 6200cp -40 F - 30 F - 32 F - 41 F - 41 F - 30 F - 38 F -17 F <0.003% Ave Phosphorous/ Zinc Content <0.003% Ave Phosphorous/ Zinc Content n/a ppm Phosphorus 812 ppm Zinc <0.003% Ave 4.8cp -25 F 0.07% Phosphorus 0.05% Zinc 1.0% 1. 0% 0. 9% 1. 0% 0.96% 0.96% 1.0% <1% Spectra Xtreme has greater shear stability which allows for improved protection and extended drain intervals. Spectra Xtreme has exceptional low temperature flow which reduces equipment warm-uptime and will improve cold temperature protection. Spectra Xtreme has a higher TBN which will extend the drain intervals and higher concentrations of anti-wear additives for greater wear protection for extended component life.

6 Value Recognition Report A Drilling Company in US Account History: The company's fleet of 8 rigs accommodates shallow-to-medium depth drilling projects. The fleet of directional tools designed to accommodate a full range of hole sizes and directional profile considerations. Pinpoint utilizes both mud pulse (MP) and electromagnetic (EM) telemetry measurement while drilling (MWD) technologies. Certified Labs Objective: Provide a reliability partner starting with a performance engine oil (SPECTRA XTREME) in place of the Simons Petroleum SPX SC to reduce oil changes and labor costs producing a recognizable savings. Using the Certified Complete Reliability-Based Partnership Model, Certified Labs is creating a value based relationship through the following in order to establish a Reliability Centered Maintenance approach using Performance Products Complete Diagnostic Support Oil and Fuel Analysis Annual Oil Cost Comparison $250, $200, $150, Generators Drawworks $100, $50, $0.00 SPX SC SPX SC Engine Oil STRATA XTREME SPECTRA EXTREME Results: Upon implementation, a recognized annual savings from extended engine oil drain intervals using SPECTRA XTREME was $111, Additional Savings will increase through a reduction of engine parts replacement, labor costs and downtime. See back for details Irving, Texas Indianapolis, Indiana Kendall Park, New Jersey Sunnyvale, California, Brampton, Ontario NCH Corporation

7 Value Recognition Report Using Caterpillar Equipment Drawworks (2 Caterpillar 3406 TA), Mud Pumps (2 Caterpillar D398), Power Swive1 (Caterpillar C-9 Engine) Oil SPX SC 15W-40 SPECTRA XTREME 14W-40 Oil Amount (5) 12 gal = 60 (5) 12 gal = 60 Oil Cost per Gallon, Unit, Total $15.61/gl, $187.32, $ $20.95/gl, $251.40, $1, Oil Filter (5) $20 (2) = $200 (5) $20 (2) = $200 Labor (5) $50 = $250 (5) $50 = $250 Cost per Change, Total Units (5) $ = $1, (5) $ = $1, Annual Change Interval 300 Hours 750 Hours Operation Runs 24/7/325 days 7,800/unit 7,800/unit Number of Units 5 5 Number of Oil Changes Annual Cost per Unit $36, $17,070 Total Annual Cost for 5 Units $180, $85, Savings -- $94, Engine Generator Sets (2 Detroit Series 60 Diesel Engines) Oil SPX SC 15W-40 SPECTRA XTREME 15W-40 Oil Amount (2) 12 gal = 24 (2) 12 gal = 24 Oil Cost per Gallon, Unit, Total $15.61/gl, , $ $20.95/gl, $251.40, $ Oil Filter (2) $20 (2) $20 Labor (2) $50 (2) $50 Cost per Change (2) $ = $ (2) $ = $ Annual Change Interval (2) at 300 Hours (2) at 1000 Hours Operation Runs 24/7/325 7,800/unit 7,800/unit Number of Units 2 2 Number of Oil Changes 26 8 Annual Cost $13, $5, Total Annual Cost for 2 Units $26, $10, Savings -- $16, Annual Savings from Extended Engine Oil Drain Intervals = $111, Additional Savings Will Increase Through a Reduction of Engine Parts Replacement, Labor Costs and Downtime. Irving, Texas Indianapolis, Indiana Kendall Park, New Jersey Sunnyvale, California Brampton, Ontario NCH Corporation

8 Spectra Xtreme CJ-4 Advanced Performance Synthetic Blend Motor Oil SAE 15W-40 Synthetic blend, multi-grade Diesel or Gasoline motor oil formulated for severe duty and extended drain intervals Provides superior protection against deposit formation, oil breakdown, parts wear, and loss of compression. Specifically Engineered for Construction Agriculture Trucking & Fleet Logging Waste Hauling Material Handling Equipment Marine Federal, State, and Local Agencies Other Industries that Utilize Heavy Equipment Synthetic Blend Formula Engineered for Extended Drain Intervals* TBN of 13 Provides Extended Acid Neutralization While Maintaining Low Ash Excellent Performance with EGR, ACERT, ASET and Turbo Charged Equipment Superior Thermal Stability for Higher Temperature Operation High Detergent Retention Prevents Deposit Build-up Contains SOLUMOL** for Superior Wear Protection Highly Resistant to Oxidation for Longer Oil Life High V.I. Number Provides Stable Viscosity Over a Wide Temperature Range Superior Cold Cranking and Oil Pumpability at Low Temperature Compatible with Synthetic, Synthetic Blend, and Mineral Based Motor Oils * Always use oil analysis to establish new drain intervals ** SOLUMOL is an oil soluble synthetic molybdenum compound Irving, Texas Indianapolis, Indiana Kendall Park, New Jersey Sunnyvale, California NCH Corporation Consult the label for complete directions and precautions before using this product. For Peak Performance, use with LubeMaster System Purge Meets or Exceeds the Following Performance Requirements API Service Classification: CJ-4 CI-4, CI-4 Plus, CH-4 Plus, CH-4, and SM for gasoline engines ACEA E&-04 (2004) MIL-PRF-2104G, CID-A-A-52306A, and CID-A-A-52039B Mack EO-O Premium Plus 07 MTU Type 2 MAN 3275 Caterpillar ECF-1-A, ECF-2, ECF-3 Cummins CES Renault RVI RLD-3 Daimler Chrysler MB228.31, MB228.3 Detroit Diesel DDC 93K218 Volvo VDS-4 Division of Certified Laboratories

9 SPECTRA XTREME Motor Oils contain a total additive package that sets it apart from all other motor oils Additives Premium, Synthetic Blend Base Oil Acid Neutralizers Friction Reducers Anti-Wear Agents Shear Stabilizers Dispersants Detergents Oxidation Inhibitors Corrosion Inhibitors Rust Inhibitors Viscosity Index Improvers Pour Point Depressants Solumol Benefits Highly-refined, oxidation-resistant synthetic blend base oils provide excptional, long-term lubrication to reduce friction, decrease heat and prevent wear. SPECTRA XTREME prevents the formation of various acids and sludge. SPECTRA XTREME outlasts conventional oils by up to 300% due to it's high residual TBN. Plate out on metal surfaces to prevent friction and wear under heavy loads. Prevents dry starts. Form a lubricant film on metal surfaces in the presence of heavy loads and high temperatures. Prevents cold welding. Increase surface viscosity and improve shear stability to carry heavier loads, withstand extreme pressures and prevent shock impact. Keep sludge, carbon, soot, varnish and gum suspended in the oil and carry them to the filter. Prevent deposits on high-contact surfaces. Keep surfaces clean and free of deposits that cause wear and increase blow-by. Extend service life of the lubricant by retarding the oxidation or breakdown process. Shield sensitive metals against acids and other corrosive compounds. Plate metal surfaces to retard metal deterioration and reduce abrasive rust contaminants. Maintain full viscosity over a wider temperature range to ensure full protection in fluctuating conditions. Eliminates the need to switch oil grades in different seasons. Keep oil flowing properly in cold temperature. Lowers frictional drag and keeps equipment running in cold temperatures. An oil soluble synthetic molybdenum compound that plates onto the metal to provide exceptional wear protection. Physical Properties TEST 15W-40 Specific Gravity (API) 29.7 Viscosity, CCS C, Max 6200 Viscosity SUS 40 C C 14.1 Viscosity Index 134 Flash Point ( F) 440 Pour Point ( F) -17 ASTM D130 Corrosion 1A Foam Suppression Sequence I 0 Sequence II 0 Sequence III 0 Sulphated Ash, % 1 TBN 13 IDEAL FOR USE: Compatible with gasoline or diesel engines or combustion engines which have been converted to natural gas. DO NOT USE: Not compatible with 2-cycle gasoline engines that mix oil with fuel.

10 Comparison of CJ-4 Engine Oils Engine Oil Test Methods, Descriptions, Test Result Values and What They Mean Engine Oil Property Amsoil CJ-4 Shell Rotella T Mobil Delvac Elite Schaeffer Supreme 7000 Chevron Ursa Plus EC Royal Purple CJ-4 Castrol Hypuron 15W-40 Certified Labs Spectra Xtreme CJ-4 Performance Benefit ASTM D 3945: Shear Stability Index Measures the percent viscosity loss at 100 C of polymer-containing fluids when evaluated by using the Fuel Injector Shear Stability Test (FISST). The less viscosity loss the better protection and lubrication. 4.2% 9.9% <3% Loss ASTM D 2270: Viscosity Index Measures variation in viscosity due to changes in temperature. The higher the number, the more stable the oil will be at varying temperatures and conditions. ASTM D 2602: Viscosity by Cold Cranking Simulator Measures the apparent viscosity of the oil at cold temperatures. The results are related to the cranking characteristics of the oil. The lower viscosity reading the easier the oil will flow at low temperatures. ASTM D 4683: High Shear/High Temperature Viscosity at the shear rate and temperature of this test method is the condition encountered in the bearings of automotive engines in severe service. Should have a minimum viscosity of 3.5 cp according to SAE. ASTM D 3829: Borderline Pumping Temperature of Engine Oil Measures the lowest temperature at which engine oil can be continuously and adequately supplied to the oil pump inlet of an automotive engine. In this case, measures viscosity at 20 C. FTM 203C: Stable Pour Point Measures the lowest temperature at which movement of the fluid is observed. The lower the pour point, the better utility the fluid has for certain applications at low temperatures. ASTM D 2896: Total Base Number (TBN) Measures the engine oil s ability to neutralize acid formation, which commonly occurs. The highest TBN for engine oil is 14. The higher the TBN, the more acid will be neutralized and the longer the oil will last. ASTM D 5158: Phosphorous/Zinc Content Measures the amount of additive elements, wear metals and contaminants in lubricating oils. Phosphorous and zinc are part of the anti-wear package. The greater the concentration in ppm s of each in the oil the better the oil will protect various engine components. ASTM D 874: Sulfated Ash Content Measures the amount of sulfated ash from unused lubricating oils containing additives. The less amount of sulfated ash the better. Engine Oil Thermal Performance and Operating Viscosity Engine Oil Anti-wear and Contamination Control Performance Ave cp 4.2cp 5,460cp 4.3cp 3250cp -20 F - 20 F - 20 F 6200cp -40 F - 30 F - 32 F - 41 F - 41 F - 30 F - 38 F -17 F <0.003% Ave Phosphorous/ Zinc Content <0.003% Ave Phosphorous/ Zinc Content n/a ppm Phosphorus 812 ppm Zinc <0.003% Ave 4.8cp -25 F 0.07% Phosphorus 0.05% Zinc 1.0% 1. 0% 0. 9% 1. 0% 0.96% 0.96% 1.0% <1% Spectra Xtreme has greater shear stability which allows for improved protection and extended drain intervals. Spectra Xtreme has exceptional low temperature flow which reduces equipment warm-uptime and will improve cold temperature protection. Spectra Xtreme has a higher TBN which will extend the drain intervals and higher concentrations of anti-wear additives for greater wear protection for extended component life.

11 Certop SN Synthetic Long Life Gear Oil 75W-90 and 80W-140 Extended drain, heavy duty synthetic gear oil specifically formulated for heavy duty trucks, construction and heavy industrial equipment. Provides superior protection against extreme temperatures, oxidation, water contamination, and foaming. ENGINEERED FOR 500,000 MILE SERVICE LIFE IN OVER-THE ROAD TRUCKS Provides Superior Equipment Protection for Utility Plants Paper Mills & Packaging Plants Steel Mills & Foundries Printing Food Processing Plants Chemical Plants, Refineries Plastic and Rubber Plants Industrial Manufacturing Resists Oxidation Longer Oil & Gear LifeResists acid, carbon and varnish formation Superior Shear Stress Stability Reduces Gear Wear Maintains viscosity during extended service life for maximum wear control and fuel efficiency Prevents Rust and Corrosion Displaces Water Contamination Controls Foaming Meets or Exceeds the Following Requirements: API GL-5 & MT-1 MIL-PRF-2105E Dana SHAES 236 (Eaton PS-163) for 500,000 miles MACK GO-J, GO-J+ Scania STO 1:0 International Navistar TMS-6816 Arvin/Meritor 0-76N (75W-90) Arvin/Meritor 0-80 (80W-140) Excellent Low Temperature Performance75W-90 down to -40ºF (-40ºC) 80W-140 down to -26ºF (-32ºC) Irving, Texas Indianapolis, Indiana Kendall Park, New Jersey Sunnyvale, California NCH Corporation Consult the label for complete directions and precautions before using this product. Division of Certified Laboratories

12 CERTOP SN contains a total additive package that sets it apart from other gear oils Additives Benefits S ynthetic grade base oil 100% PAO synthetic oil base that resists breakdown to provide longer oil life. Provides superior lubrication at a wider temperature range. Anti-Wear Agents Forms a lubricant film on metal surfaces in the presence of heavy loads and high temperatures. Prevents cold welding. Friction Reducers Plates out on metal surfaces to prevent friction and wear under heavy loads. Blocks out corrosive elements such as acids, water, condensate and steam by Rust and Corrosion Inhibitors forming a protective barrier on equipment surfaces to prevent chemical wear. Heat seeking additive which increases the ability of the lubricant to prevent the Extreme Pressure (EP) Agents extreme wear that can occur under loads. Oxidation Inhibitors Extends service life of the lubricant by retarding the oxidation or breakdown process. S hock Load Reducers Cushions impact to minimize the stress, vibration and chatter that can occur under heavy loads and during start-stop operations. Physical Properties TEST Viscosity 100 C, cst [ASTM D 445] Viscosity 40 C, cst [ASTM D 445] Viscosity Index Specific Gravity (g/ml) Flash Point, C ( F ) (COC) [ASTM D 92] Pour Point C ( F ) [ASTM D 97] Brookfield Visc. [ASTM D 2983] Foam Tendency [ASTM D 892] 75W (401) -48 (-54) < (-40 C) cp PASS 80W (410) -36 (-33) <150000(-26 C) cp PASS IDEAL FOR USE IN: Power Dividers, Gear Trains, Bronze Gears (up to 200 F) and Gear Boxes including enclosed gears of spur type, hypoid, spiral bevel, worm, herringbone, helical, planetary and unusual combinations of gear types, Differentials, Limited-Slip Differentials, Simple Manual Transmissions, Axles. Certop SN has been fully tested and field proven, demonstrating outstanding wear protection and oxidation resistance throughout a 500,000- mile service life in over-the-road trucks. DO NOT USE FOR: Gear boxes that only allow the use of GL-1 gear oil / motor oil (use STRATA Motor Oils) or any other equipment for which the manufacturer does not recommend this type of gear lubricant. Never mix with asphaltic-type or SCL -type lubricants.