FLUIDS, LUBRICANTS AND GENUINE PARTS

Transcription

1 FLUIDS, LUBRICANTS AND GENUINE PARTS ENGINE Description Cooling System (2.7L Liters (3.5L Liters (3.5L Export and ALL Wheel Drive Liters (5.7L Liters (5.7L Export and Severe Duty II Cooling System Liters (6.1L Liters (3.0L Diesel Liters Engine Oil with Filter Engine Oil (2.7L MOPAR API Certified SAE 5W-20 engine oil, AC AD Liters Engine Oil (3.5L MOPAR API Certified SAE 10W-30 engine oil, AC AD Liters Engine Oil (5.7L MOPAR API Certified SAE 5W-20 engine oil, AC AD Liters Engine Oil (6.1L For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils that meet AB Liters

2 Description the American Petroleum Institute (API) categories of SM or SM/CF, and meet the requirements of Chrysler Material Standard MS The manufacturer recommends the use of a full synthetic engine oil, such as Pennzoil Platinum European Formula SAE 5W-40 or equivalent. For additional information, refer to the Engine Oil Selection and Engine Oil Viscosity (SAE Grade) in the Maintenance Procedures section of this manual. Engine Oil (3.0L Diesel API Certified SAE 5W-30 Synthetic Engine Oil, Standard MS or Mercedes Benz MB and ACEA C3 qualified engine oils. 1 Liter AA Liters Engine Oil Filter (Gasoline Engines) ALL Engine Oil Filter (3.0L Diesel MOPAR Engine Oil Filter MOPAR Engine Oil Filter AA Fuel (approximate) Fuel Selection (2.7L 87 Octane Unleaded Fuel, Domestic 91 Octane Unleaded Fuel, Export Liters Fuel Selection (3.5L 87 Octane Unleaded Fuel Acceptable - 89 Octane Recommended - Domestic 91 Octane Unleaded Fuel Acceptable - 95 Octane Recommended - Export With AWD - Without AWD - 18 With AWD - Without AWD - 68 Liters Fuel Selection (5.7L 87 Octane Unleaded Fuel Acceptable - 89 Octane Recommended - Domestic 91 Octane Unleaded Fuel Acceptable - 95 Octane Recommended - Export Fuel Selection (6.1L 91 Octane or higher Premium Unleaded - Domestic 98 Octane Premium Unleaded - Export Fuel Selection (3.0L Diesel Engines) Use good quality diesel fuel from a reputable supplier in your vehicle. The manufacturer requires that you must fuel this vehicle with Ultra Low Sulfur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid damage to the emissions control system. For most year-round service, No. 2 diesel fuel meeting ASTM specification D-975 Grade S15 will provide good performance. If the vehicle is exposed to extreme cold (below 20F or -7C), or is

3 Description required to operate at colder-than-normal conditions for prolonged periods, use climatized No. 2 diesel fuel or dilute the No. 2 diesel fuel with 50% No. 1 diesel fuel. This will provide better protection from fuel gelling or wax-plugging of the fuel filters. This vehicle is fully compatible with biodiesel blends up to 5% biodiesel meeting ASTM specification D-975. A/C Refrigerant System Refrigerant R-134a AB Pounds Kilograms System fill capacity includes heater and coolant recovery bottle filled to MAX level. For countries that use the ACEA European Oil Categories for Service Fill Oils, use the recommended engine oil that meets the requirements of ACEA C3, and approved to MB or MB only. Refer to your engine oil filler cap for correct SAE grade. For best performance and maximum protection under all types of operating conditions, Export vehicles equipped with a 6.1L engine, use 98 Octane Premium Unleaded Fuel only. SPARK PLUGS Gap Spark Plugs (2.7L Champion Single Platinum AC (TE10PMC5) in mm Spark Plugs (3.5L NGK Single Platinum AB (ZFR5LP13G) in mm Spark Plugs (5.7L Champion Nickel AB (REC14MCC4) in mm Spark Plugs (6.1L NGK Double Platinum AA (PLZTR5A-13) in mm TRANSMISSION Automatic

4 42RLE - Service Fill AA AA Liters 42RLE- Overhaul Fill AA AA Liters NAG 1 - Service Fill AA AA Liters NAG 1 - Overhaul Fill AA AA Liters Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information for the correct procedures. TRANSFER CASE MS140 MOPAR Transfer Case Lubricant AA 1.3 Pints 0.6 Liters CHASSIS Axles (Front) 175mm FIA Front Axle SAE 75W AA 1.26 Pints 0.6 Liters

5 Axles (Rear) 8mm RII Rear Axle Liters 210mm RII Rear Axle Liters 215mm RII Rear Axle Liters 226mm RII Rear Axle SAE 75W AA Liters Chassis Systems Brake Master Cylinder MOPAR Brake Fluid DOT 3, SAE J oz. Bottle AB 32 oz. Bottle AB Power Steering Reservoir MOPAR Power Steering Fluid AA Limited-Slip Rear Axles require the addition of 118 ml (4 oz.) MOPAR Limited Slip Additive. If MOPAR Brake Fluid DOT 3 is not available, then MOPAR Brake and Clutch Fluid DOT 4 (P/N AC), is acceptable. If MOPAR Power Steering Fluid +4 is not available, then MOPAR ATF +4 Automatic (P/N AA), is acceptable. If equipped with Trailer Tow package use,