Centrifugal pumps. Main catalogue.

Size: px
Start display at page:

Download "Centrifugal pumps. Main catalogue."

Transcription

1 Main catalogue EN Centrifugal pumps for machine tools and filter systems, printing and packaging machines, temperature control units Quality Management DIN EN ISO 9001:08 Environmental Management DIN EN ISO 101 Health and Safety Management OHSAS 18001

2 Table of content A solution for every application...2 Technical information....3 PRG...8 PRK...12 PSR...16 PXA...28 PS/PSL PMS...44 PSH...56 Order keys for all pumps A solution for every application Main applications Machine tools / filter systems Printing machines / packaging machines Temperature control units Immersion pumps for slightly contaminated fluids Optical devices Designation Q max [l/min] H max [m] Type Page PRG centrifugal pump 8 PRK centrifugal pump 12 PSR centrifugal pump 16 PXA centrifugal pump 28 PS centrifugal pump 36 PSL centrifugal pump 36 Immersion pumps for highly contaminated fluids Designation Q max [l/min] H max [m] Type Page PMS 0 45 centrifugal pump 44 PSH centrifugal pump 56

3 spandaupumpen.com Centrifugal pumps 3 Technical Information Electrical specifications Introduction The drive motors meet VDE regulations and European motor standards with an electrical voltage tolerance of ±5% (DIN EN ) as well as the requirements for the CE mark. We also provide designs for special operating conditions (e.g., extreme humidity or dust). Designs are possible that conform to non-european regulations, e.g. CSA, UL or special requirements, e.g. for the USA or Japan. Efficiency classification as per DIN EN The drive motors meet at least efficiency IE2. Efficiency Super Premium Premium High Standard IE code IE4 IE3 IE2 IE1 Protection class (DIN EN /4.88) IP 54 Below Standard - Temperature class Pole pairs Ambient temperature (DIN EN ) Electrical parameters* F 2-pole Max. C At max above sea level 50 Hz 60 Hz 4 kw /Y 230/0 V /Y 265/460 V > 4 kw 0 V 460 V * other electrical parameters on request For connection to 60 Hz, in addition to selection of the corresponding motor winding, the hydraulic properties are adjusted at the factory, for example using smaller impellers. Switching-on frequency Spandau pumps are designed for continuous duty. If this is not possible due to the process, the pump's constant flow rate can be attained using a regulating valve, for example. Motors < 3 kw 0 3 to 5.5 kw Max. duty cycles per hour Sound pressure specifications All sound pressure values indicated in the catalog apply to 50 Hz operation. In 60 Hz operation, the values increase by approx. 3 4 dba. On request, axial fans on the motor side are available to reduce noise. Frequency converters Pumps with frequency converters achieve up to 70% energy savings in practice. The controlled speed regulation ensures an effective delivery rate and utilization with lower heat input into the overall system. This reduces the required cooling effort. A pump with an integrated frequency converter improves the process flows of machines and systems: Optimized adaptation to the respective machining process due to speed regulation Gentle start-up due to programmable ramp-up time Low level of wear on rotating components Low-noise operation Keep the entire machining process under control with a single frequency-controlled pump: Delivery rate can be adjusted precisely to the respective power requirements Universal controllability of pump speeds through all pressure ranges 7.5 to 10 kw > 10 kw 15 DESINA (DistributEd and Standardized INstAllation technology for machine tools and production systems) is a complete concept for the standardization of the electrical, hydraulic, and pneumatic installation of automated machine tools and production systems. Spandau pumps are available with DESINA-compliant electrical connections on request.

4 4 Centrifugal pumps spandaupumpen.com Technical Information Electrical specifications Star-delta connection Delta connection Star connection Y L1 U1 W2 L1 U1 W2 L2 V1 U2 L2 V1 U2 L3 W1 V2 L3 W1 V2 Speed switch Switchover 4/2 pole Y with pole-changing switch For optional changeover to half speed YY without pole-changing switch U1 U2 L1 U1 U2 U1 U2 L1 V1 V2 L2 V1 V2 V1 V2 L2 W1 W2 L3 W1 W2 W1 W2 L3 Slow Y Fast YY Dahlander connection Voltage switchover 1:2 YY low voltage Voltage switchover 1:2 Y high voltage L1 U Z L1 U Z L2 V X L2 V X L3 W Y L3 W Y Y Y Y Steinmetz-connection Clockwise direction of rotation when viewing the motor fan Clockwise direction of rotation when viewing the motor fan

5 spandaupumpen.com Centrifugal pumps 5 Technical Information Electrical specifications Site altitude and ambient temperature The following tables show the permissible temperature limits based on a coolant temperature of C and a site altitude up to 1000 m above sea level (measured with the resistance method) and maximum temperatures according to DIN EN assigned to temperature class F. Temperature class Winding temperature [ C] < 600 W > 600 W Max. temperature [ C] Terminal box positions The position of the terminal box is specified according to DIN EN and can be selected from the four layouts depicted below. Pos. Layout Note 1 Terminal box position 1: Discharge Standard design* port Terminal box opposite the discharge port F Reduced rated motor performance results if the relevant ambient conditions deviate from the design point, e.g., ambient temperature above C or site altitude above 1000 m above sea level. Deviations in the ambient conditions must be indicated when ordering. Reduced performance at ambient temperature above C Terminal box 2 Terminal box position 2: Terminal box left of discharge port Ambient temperature [ C] (site altitude up to 1000 m above sea level) Performance [%P N ] Terminal box position 3: Terminal box above discharge port Reduced performance at altitude over 1000 m above sea level Site altitude [m] ( C ambient temperature) Performance [%P N ] Terminal box position 4: Terminal box right of discharge port Overload capacity At a normal operating temperature, under DIN EN /11/ times the rated current over a period of 15 seconds is permissible at rated voltage and rated current. * Please indicate desired position of terminal box when ordering! Varnishing Standard: RAL 9005 (black, satin)

6 6 Centrifugal pumps spandaupumpen.com Technical Information Installation and operation Centrifugal pumps The standard design is suitable for vertical installation in the reservoir. Spandau immersion pumps can be adapted to various installation conditions by incorporating blind chambers or by adding a pipe extension. When switching on the pump, the minimum fluid level must be above the lowest pump chamber (1). The pump then feeds up to the intake opening in the chamber or pipe (2). See the type-specific pump drawings in manuals for the highest permissible fluid level (3). With empty chambers: Designs With pipe extension: Note: All devices are only to be installed or mounted by a qualified person. The existing safety measures are to be taken into consideration. Please refer to our operating instructions to avoid errors. Dry running The pump must not be put into operation without fluid for pumping. An incorrect direction of rotation and/or dry running can damage the pump. When pumping, the unit can operate without fluid for short periods and under certain circumstances. A minimum volumetric flow of 5 to 10% of the nominal delivery rate must be ensured.

7 spandaupumpen.com Centrifugal pumps 7 Order code for centrifugal pumps based on the PSR pump as an example P S R Series Frame size 02 = 2 m³/h (nominal delivery rate) 04 = 4 m³/h (nominal delivery rate) 06 = 6 m³/h (nominal delivery rate) Stages To determine the desired number of stages the corresponding characteristics has to be used. 01 = 1-stage = 30-stages s G = gray cast iron (standard) C = GG with chemical surface sealing T = GG coated with paint Seal B = gap bush (H max < 150 m) G = machanical seal (H max > 150 m) Pump design S = standard design V = bottom for extension tube C = bottom equipped with intake strainer Immersion depth in mm To determine the desired immersion depth the appropriate table "Electrical data, dimensions and weights" has to be used. 122 = 122 mm = 739 mm Motor index To determine the desired motor index the appropriate table "Electrical data, dimensions and weights" has to be used. Example: E = 0,37 kw Power supply 01 = 230 /0 V at 50 Hz (to 4 kw) 265 /460 V at 60 Hz (to 4,6 kw) 02 = 0 V at 50 Hz (from 5,5 kw) 460 V at 60 Hz (from 6,3 kw) 05 = Standard for Europe 230/0 V at 50 Hz (from 4 kw) 0 V at 50 Hz (from 4 kw)... further designs on request Motor design AA = standard to 0,55 kw (insulation class F, IP 54, 2-pole) BA = standard from 0,75 kw (insulation class F, IP 54, 2-pole, IE2)... further designs on request Order example: PSR0218GBS481J01BA Series: PSR, Frame size: 02, 18-stages, : G grey cast iron, Seal: B gap bush, Pump design: S standard design, Immersion depth: 481 mm, Motor index: J 1,5 kw, Power supply: /0 V 50 Hz; 265/460 V 60Hz, Motor design: BA standard form 0,75 kw

8 8 Centrifugal pumps spandaupumpen.com PRG Immersion pumps, sealless 50 Hz, closed impellers PRG p [psi] H [m] 50 Hz PRG 4-stages 30 Features Delivery head 1) 15 PRG 3-stages One or multi-stages centrifugal pump For delivery of slightly contaminated types of fluids Installation direcly and vertically into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G1 1/ PRG 2-stages PRG 1-stage Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 62 l/min Delivery head H max 23 m Flange POM / GF Mixing paddle plastic Immersion depth t max 3 mm Shaft Immersion depth max. mm 2 /s Delivery temperature - C to +60 C Grain size Contamination Direction of rotation max. Ø0,3 mm max. 50 g/m³ clockwise (as viewed looking down on the motor's ventilation side) Impeller Intermediate chamber Pumps bottom Bushing PEI / GF POM / GF POM / GF PTFE graphite Fluids delivered Water, emulsions (synthetic / mineral oil), also with chemical additives, distilled water deionization, ized water, photographic solutions 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

9 spandaupumpen.com Centrifugal pumps 9 PRG Immersion pumps, sealless 50 Hz, closed impellers PRG k Øm t l Ø115/4xØ7 Ø G¾ 25 max. level of fluid min. level of fluid Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size PRG 06 Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) 230/0 A 0,09 0,46/0, ,8 3,1 44 G¾ 230/0 B 0,12 0,71/0, ,9 3,3 45 G¾ 230/0 C 0,18 0,86/0, ,5 4,9 48 G¾ 230/0 E 0,37 1,72/1, ,8 5,0 49 G¾

10 10 Centrifugal pumps spandaupumpen.com PRG Immersion pumps, sealless 60 Hz, closed impellers PRG p [psi] H [m] 30 PRG 4-stages 60 Hz 25 PRG 3-stages 30 Features Delivery head 1) 15 PRG 2-stages One or multi-stages centrifugal pump For delivery of slightly contaminated types of fluids Installation direcly and vertically into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G1 1/ PRG 1-stage Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 50 l/min Delivery head H max 32 m Flange POM / GF Mixing paddle plastic Immersion depth t max 3 mm Shaft Immersion depth max. mm 2 /s Delivery temperature - C to +60 C Grain size Contamination Direction of rotation max. Ø0,3 mm max. 50 g/m³ clockwise (as viewed looking down on the motor's ventilation side) Impeller Intermediate chamber Pumps bottom Bushing PEI / GF POM / GF POM / GF PTFE graphite Fluids delivered Water, emulsions (synthetic / mineral oil), also with chemical additives, distilled water deionization, ized water, photographic solutions 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

11 spandaupumpen.com Centrifugal pumps 11 PRG Immersion pumps, sealless 60 Hz, closed impellers PRG k Øm t l Ø115/4xØ7 Ø G¾ 25 max. level of fluid min. level of fluid Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size PRG 06 Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) 265/460 A 0,10 0,46/0, ,8 3,1 45 G¾ 265/460 B 0,14 0,71/0, ,9 3,3 46 G¾ 265/460 C 0,21 0,86/0, ,5 4,9 50 G¾ 265/460 E 0,42 1,72/1, ,8 5,0 51 G¾

12 12 Centrifugal pumps spandaupumpen.com PRK Immersion pumps, hydrostatic sealing 50 Hz, open impellers p [psi] H [m] 50 Hz 30 PRK 5 stages PRK PRK 4 stages Features Delivery head 1) 15 PRK 3 stages Vertical multistage pump, hydrostatic sealing For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G3/4 Wide range of immersion depths mm PRK 2 stages PRK 1 stage Q [l/min] Q [USgpm] Delivery rate 1) Technical data Mechanical design Variations Delivery rate Q max 175 l/min Delivery head H max 29 m Immersion depth t max 375 mm Kinematic viscosity max. mm 2 /s Flange POM Base PPS Shaft Intake strainer Extension tube PP Delivery temperature +5 C to +60 C Impeller POM Grain size max. Ø3 mm Diffuser PP Contamination Direction of rotation max. 50 g/m³ anti-clockwise (as viewed looking down on the motor's ventilation side) Intermediate chamber Bearings PPS Deep groove ball bearing with covering disk Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, water, mild acids Pumps bottom Elastomers PP NBR 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

13 spandaupumpen.com Centrifugal pumps 13 Symbolisierung der verschiedenen Fördermedien PRK Immersion pumps, hydrostatic sealing 50 Hz, open impellers stark verunreinigte Fördermedien leicht verunreinigte Fördermedien reine Fördermedien k Øm Variation "C" with intake strainer PRK Ø115/4xØ7 t l Ø G¾ 25 max. level of fluid min. level of fluid 35 Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size PRK 03 Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port series (DIN ISO 228) 230/0 D 0,25 1,11/0, ,0 4,4 45 G¾ 230/0 E 0,37 1,72/1, ,2 4,6 48 G¾ 230/0 F 0,55 2,06/1, ,4 4,8 52 G¾ 230/0 G 0,75 2,56/1, ,1 8,5 54 G¾ 230/0 H 1,1 4,07/2, ,3 8,7 58 G¾

14 14 Centrifugal pumps spandaupumpen.com PRK Immersion pumps, hydrostatic sealing 60 Hz, open impellers p [psi] H [m] PRK 4 stages 60 Hz 30 PRK 25 PRK 3 stages 30 Features Delivery head 1) 15 PRK 2 stages Vertical multistage pump, hydrostatic sealing For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G3/4 Wide range of immersion depths mm PRK 1 stage Q [l/min] Q [USgpm] Delivery rate 1) Technical data Mechanical design Variations Delivery rate Q max 170 l/min Delivery head H max 33 m Immersion depth t max 375 mm Kinematic viscosity max. mm 2 /s Flange POM Base PPS Shaft Intake strainer Extension tube PP Delivery temperature +5 C to +60 C Impeller POM Grain size max. Ø3 mm Diffuser PP Contamination Direction of rotation max. 50 g/m³ anti-clockwise (as viewed looking down on the motor's ventilation side) Intermediate chamber Bearings PPS Deep groove ball bearing with covering disk Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, water, mild acids Pumps bottom Elastomers PP NBR 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

15 spandaupumpen.com Centrifugal pumps 15 PRK Immersion pumps, hydrostatic sealing 60 Hz, open impellers k Øm PRK Ø115/4xØ7 t l Ø G¾ 25 max. level of fluid min. level of fluid 35 Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size PRK 03 Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port series (DIN ISO 228) 265/460 E 0,42 1,72/1, ,0 4,4 48 G¾ 265/460 F 0,62 2,06/1, ,2 4,6 52 G¾ 265/460 G 0,86 2,56/1, ,9 8,3 54 G¾ 265/460 H 1,26 4,07/2, ,1 8,5 58 G¾

16 16 Centrifugal pumps spandaupumpen.com PSR 02 Immersion pumps, sealless 50 Hz, closed impellers p [psi] H [m] Hz PSR Features Vertical multistage coolant pump Connector dimensions as per DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Delivery head 1) Pressure port is located above the reservoir plate and designed with internal thread G1 1/ Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 60 l/min Delivery head H max Immersion depth t max 230 m 739 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size Contamination max. Ø2 mm max. 50 g/m³ Flange Shaft Gap bush (H max < 150 m) Mechanical seal (H max > 150 m) POM WC, carbon, FKM, stainless steel Flange Bottom for extension tube Intake strainer with chemical surface sealing or coated with paint Direction of rotation clockwise (as viewed looking down on the motor's ventilation side) Impeller Intermediate chamber Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, water, mild acids Tension anchor Bushing 1.57 Pumps bottom Elastomers FPM 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

17 spandaupumpen.com Centrifugal pumps 17 PSR 02 Immersion pumps, sealless 50 Hz, closed impellers k Øm G1 ¼ G1 ¼ PSR l Symbolisierung der verschiedenen Fördermedien stark verunreinigte Fördermedien leicht verunreinigte Fördermedien reine Fördermedien Variation "V" with bottom for extension tube Variation "C" with intake strainer Ø160 / 4 Ø9 100 max. level of fluid t min. level of fluid 70 Øq Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PSR , ,4 E 0,37 1,57 / 0, , , , F 0,55 2,06 / 1, , , ,3 G 0,75 2,56 / 1, , ,0 230/ H 1,1 4,07 / 2, , , , J 1,5 4,95 / 2, , , , , K 2,2 7,15 / 4, , , , G1¼

18 18 Centrifugal pumps spandaupumpen.com PSR 02 Immersion pumps, sealless 60 Hz, closed impellers p [psi] 300 H [m] Hz PSR Features Vertical multistage coolant pump Connector dimensions as per DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Delivery head 1) Pressure port is located above the reservoir plate and designed with internal thread G1 1/ Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 68 l/min Delivery head H max Immersion depth t max 245 m 567 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size Contamination Direction of rotation max. Ø2 mm max. 50 g/m³ clockwise (as viewed looking down on the motor's ventilation side) Flange Shaft Gap bush (H max < 150 m) Mechanical seal (H max > 150 m) Impeller Intermediate chamber POM WC, carbon, FKM, stainless steel Flange Bottom for extension tube Intake strainer with chemical surface sealing or coated with paint Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, water, mild acids Tension anchor Bushing 1.57 Pumps bottom Elastomers FPM 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

19 spandaupumpen.com Centrifugal pumps 19 PSR 02 Immersion pumps, sealless 60 Hz, closed impellers k Øm G1 ¼ 30 t 32 G1 ¼ PSR l Variation "V" with bottom for extension tube Variation "C" with intake strainer Ø160 / 4 Ø9 100 max. level of fluid min. level of fluid 70 Øq Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PSR ,1 E 0,42 1,57 / 0, , F 0,62 2,06 / 1, , ,0 G 0,86 2,56 / 1, , , H 1,26 4,07 / 2, , ,5 265/ , J 1,8 5,0/2, , , , K 2,6 7,5/4, , , ,7 L 3,6 10,1/5, ,3 G1¼

20 Centrifugal pumps spandaupumpen.com PSR 04 Immersion pumps, sealless 50 Hz, closed impellers p [psi] 300 H [m] Hz PSR Features Vertical multistage coolant pump Connector dimensions as per DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Delivery head 1) Pressure port is located above the reservoir plate and designed with internal thread G1 1/ Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 110 l/min Delivery head H max Immersion depth t max 232 m 653 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size Contamination Direction of rotation max. Ø2 mm max. 50 g/m³ clockwise (as viewed looking down on the motor's ventilation side) Flange Shaft Gap bush (H max < 150 m) Mechanical seal (H max > 150 m) Impeller Intermediate chamber POM WC, carbon, FKM, stainless steel Flange Bottom for extension tube Intake strainer with chemical surface sealing or coated with paint Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, water, mild acids Tension anchor Bushing 1.57 Pumps bottom Elastomers FPM 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

21 spandaupumpen.com Centrifugal pumps 21 PSR 04 Immersion pumps, sealless 50 Hz, closed impellers k Øm G1 ¼ 30 t 32 G1 ¼ PSR l Variation "V" with bottom for extension tube Variation "C" with intake strainer Ø160 / 4 Ø9 100 max. level of fluid min. level of fluid 70 Øq Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size PSR 04 Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq Weight [kg] Sonic pressure [dba] E 0,37 1,57 / 0, , ,4 F 0,55 2,06 / 1, , G 0,75 2,56 / 1, , ,7 H 1,1 4,07 / 2, , , J 1,5 4,95 / 2, , ,8 230/ , K 2,2 7,15 / 4, , , , L 3,0 10,0 / 5, , , , M 4,0 13,0 / 7, , ,2 Pressure port (DIN ISO 228) G1¼

22 22 Centrifugal pumps spandaupumpen.com PSR 04 Immersion pumps, sealless 60 Hz, closed impellers p [psi] 300 H [m] Hz PSR Features Vertical multistage coolant pump Connector dimensions as per DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Delivery head 1) Pressure port is located above the reservoir plate and designed with internal thread G1 1/ Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 130 l/min Delivery head H max Immersion depth t max 238 m 481 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size Contamination Direction of rotation max. Ø2 mm max. 50 g/m³ clockwise (as viewed looking down on the motor's ventilation side) Flange Shaft Gap bush (H max < 150 m) Mechanical seal (H max > 150 m) Impeller Intermediate chamber POM WC, carbon, FKM, stainless steel Flange Bottom for extension tube Intake strainer with chemical surface sealing or coated with paint Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, water, mild acids Tension anchor Bushing 1.57 Pumps bottom Elastomers FPM 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

23 spandaupumpen.com Centrifugal pumps 23 PSR 04 Immersion pumps, sealless 60 Hz, closed impellers k Øm G1 ¼ 30 t 32 G1 ¼ PSR l Variation "V" with bottom for extension tube Variation "C" with intake strainer Ø160 / 4 Ø9 100 max. level of fluid min. level of fluid 70 Øq Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size PSR 04 Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq Weight [kg] Sonic pressure [dba] F 0,62 2,06 / 1, , G 0,86 2,56 / 1, , H 1,26 4,07 / 2, , ,6 J 1,8 5,0/2, , ,8 265/460 K 2,6 7,5/4, , , L 3,6 10,1/5, , , ,0 M 4,5 12,7/7, , ,2 460 N 6,2 11, ,8 72 Pressure port (DIN ISO 228) G1¼

24 24 Centrifugal pumps spandaupumpen.com PSR 06 Immersion pumps, sealless 50 Hz, closed impellers p [psi] 350 H [m] Hz PSR Delivery head 1) Features Vertical multistage coolant pump Connector dimensions as per DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G1 1/ Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 150 l/min Delivery head H max Immersion depth t max 255 m 747 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size Contamination Direction of rotation max. Ø2 mm max. 50 g/m³ clockwise (as viewed looking down on the motor's ventilation side) Flange Shaft Gap bush (H max < 150 m) Mechanical seal (H max > 150 m) Impeller Intermediate chamber POM WC, carbon, FKM, stainless steel Flange Bottom for extension tube Intake strainer with chemical surface sealing or coated with paint Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, water, mild acids Tension anchor Bushing 1.57 Pumps bottom Elastomers FPM 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

25 spandaupumpen.com Centrifugal pumps 25 PSR 06 Immersion pumps, sealless 50 Hz, closed impellers k Øm G1 ¼ 32 G1 ¼ PSR l Variation "V" with bottom for extension tube 30 Variation "C" with intake strainer Ø160 / 4 Ø9 100 max. level of fluid t min. level of fluid 70 Øq Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size PSR 06 Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq Weight [kg] Sonic pressure [dba] F 0,55 2,06/1, , G 0,75 2,56/1, , ,9 H 1,1 4,07/2, , ,8 J 1,5 4,95/2, , ,5 230/ K 2,2 7,15/4, , , , L 3,0 10,0/5, , , ,1 M 4,0 13,0/7, , , ,5 0 N 5,5 11, , ,0 Pressure port (DIN ISO 228) G1¼

26 26 Centrifugal pumps spandaupumpen.com PSR 06 Immersion pumps, sealless 60 Hz, closed impellers p [psi] 350 H [m] Hz PSR Features Delivery head 1) Vertical multistage coolant pump Connector dimensions as per DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G1 1/ Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 180 l/min Delivery head H max Immersion depth t max 255 m 547 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size Contamination Direction of rotation max. Ø2 mm max. 50 g/m³ clockwise (as viewed looking down on the motor's ventilation side) Flange Shaft Gap bush (H max < 150 m) Mechanical seal (H max > 150 m) Impeller Intermediate chamber POM WC, carbon, FKM, stainless steel Flange Bottom for extension tube Intake strainer with chemical surface sealing or coated with paint Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, water, mild acids Tension anchor Bushing 1.57 Pumps bottom Elastomers FPM 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

27 spandaupumpen.com Centrifugal pumps 27 PSR 06 Immersion pumps, sealless 60 Hz, closed impellers k Øm G1 ¼ 32 G1 ¼ PSR l Variation "V" with bottom for extension tube 30 Variation "C" with intake strainer Ø160 / 4 Ø9 100 max. level of fluid t min. level of fluid 70 Øq Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size PSR 06 Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq Weight [kg] Sonic pressure [dba] F 0,62 2,06/1, , G 0,86 2,56/1, , H 1,26 4,07/2, , J 1,75 4,95/2, , ,5 K 2,55 7,15/4, /460 27, ,7 L 3,45 10,0/5, , , M 4,6 13,0/7, , , ,0 N 6,2 11, , ,0 O 8,6 14, ,8 Pressure port (DIN ISO 228) G1¼

28 28 Centrifugal pumps spandaupumpen.com Symbolisierung der verschiedenen Fördermedien stark verunreinigte Fördermedien leicht verunreinigte Fördermedien PXA 10 Immersion pumps, sealless 50 Hz, closed impellers reine Fördermedien p [psi] 3 H [m] 2 50 Hz PXA Features Vertical multistage centrifugal pump For delivery of slightly contaminated fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate Delivery head 1) Pressure port is designed with internal thread G Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 195 l/min Delivery head H max Immersion depth t max 235 m 680 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size max. Ø2 mm Flange Shaft Impeller Intermediate chamber EN-GJS Mechanical seal Bottom for extension tube Intake strainer WC, Carbide, FPM, Stainless steel Contamination max. 50 g/m 3 Direction of rotation clockwise (as viewed looking down on the motor's ventilation side) Tension anchor Pumps bottom Elastomers 1.57 EN-GJL-250 FPM Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, mild acids Bearings Gap bush (H max < 150 m) Deep groove ball bearing with covering disk POM Mechanical seal (H max > 150 m) WC, Carbide, FPM, Stainless steel ) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

29 l spandaupumpen.com Centrifugal pumps 29 Symbolisierung der verschiedenen Fördermedien stark verunreinigte Fördermedien leicht verunreinigte Fördermedien PXA 10 Immersion pumps, sealless 50 Hz, closed impellers reine Fördermedien k Øm Variation "V" with bottom for extension tube G 2 Øq G2 45 s 45 Variation "C" with intake strainer PXA Ø2 / 4x Ø14 t 125 max. level of fluid min. level of fluid 70 Ø180 Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq s Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PXA G 0,75 2,75/1, H 1,1 3,95/2, J 1,5 5,2/3, K 2,2 7,4/4, / L 3,0 9,9/5, M 4,0 12,7/7, N 5,5 9, O 7,5 13, G2

30 30 Centrifugal pumps spandaupumpen.com Symbolisierung der verschiedenen Fördermedien stark verunreinigte Fördermedien leicht verunreinigte Fördermedien PXA 10 Immersion pumps, sealless 60 Hz, closed impellers reine Fördermedien p [psi] 3 H [m] Hz PXA Features Vertical multistage centrifugal pump For delivery of slightly contaminated fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate Delivery head 1) Pressure port is designed with internal thread G Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 300 l/min Delivery head H max Immersion depth t max 230 m 518 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size max. Ø2 mm Flange Shaft Impeller Intermediate chamber EN-GJS Mechanical seal Bottom for extension tube Intake strainer WC, Carbide, FPM, Stainless steel Contamination max. 50 g/m 3 Direction of rotation clockwise (as viewed looking down on the motor's ventilation side) Tension anchor Pumps bottom Elastomers 1.57 EN-GJL-250 FPM Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, mild acids Bearings Gap bush (H max < 150 m) Deep groove ball bearing with covering disk POM Mechanical seal (H max > 150 m) WC, Carbide, FPM, Stainless steel ) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

31 l spandaupumpen.com Centrifugal pumps 31 Symbolisierung der verschiedenen Fördermedien stark verunreinigte Fördermedien leicht verunreinigte Fördermedien PXA 10 Immersion pumps, sealless 60 Hz, closed impellers reine Fördermedien k Øm Variation "V" with bottom for extension tube G 2 Øq G2 45 s 45 Variation "C" with intake strainer PXA Ø2 / 4x Ø14 t 125 max. level of fluid min. level of fluid 70 Ø180 Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq s Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PXA J 1,75 Y 2, K 2,54 Y 4, Y L 3,45 Y 5, M 4,55 Y 7, N 6,3 9, O 8,6 13, P 12,6 19, G2

32 32 Centrifugal pumps spandaupumpen.com Symbolisierung der verschiedenen Fördermedien stark verunreinigte Fördermedien leicht verunreinigte Fördermedien PXA 18 Immersion pumps, sealless 50 Hz, closed impellers reine Fördermedien p [psi] 3 H [m] Hz PXA Features Vertical multistage centrifugal pump For delivery of slightly contaminated fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate Delivery head 1) Pressure port is designed with internal thread G Q [l/min] Q [USgpm] Delivery rate 1)) Technical Data Mechanical design Variations Delivery rate Q max 390 l/min Delivery head H max Immersion depth t max 230 m 692 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size max. Ø2 mm Flange Shaft Impeller Intermediate chamber EN-GJS Mechanical seal Bottom for extension tube Intake strainer WC, Carbide, FPM, Stainless steel Contamination max. 50 g/m 3 Direction of rotation clockwise (as viewed looking down on the motor's ventilation side) Tension anchor Pumps bottom Elastomers 1.57 EN-GJL-250 FPM Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, mild acids Bearings Gap bush (H max < 150 m) Deep groove ball bearing with covering disk POM Mechanical seal (H max > 150 m) WC, Carbide, FPM, Stainless steel ) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

33 l spandaupumpen.com Centrifugal pumps 33 Symbolisierung der verschiedenen Fördermedien stark verunreinigte Fördermedien leicht verunreinigte Fördermedien PXA 18 Immersion pumps, sealless 50 Hz, closed impellers reine Fördermedien k Øm Variation "V" with bottom for extension tube G 2 Øq G2 45 s 45 Variation "C" with intake strainer PXA Ø2 / 4x Ø14 t 125 max. level of fluid min. level of fluid 70 Ø180 Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq s Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PXA K 2,2 7,4/4, /0 L 3,0 9,9/5, M 4,0 12,7/7, N 5,5 9, O 7,5 13, P 11,0 19, Q 15,0 27, G2

34 34 Centrifugal pumps spandaupumpen.com Symbolisierung der verschiedenen Fördermedien stark verunreinigte Fördermedien leicht verunreinigte Fördermedien PXA 18 Immersion pumps, sealless 60 Hz, closed impellers reine Fördermedien p [psi] 3 H [m] Hz PXA Features Vertical multistage centrifugal pump For delivery of slightly contaminated fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate Delivery head 1) Pressure port is designed with internal thread G Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 500 l/min Delivery head H max Immersion depth t max 250 m 554 mm Kinematic viscosity max. mm 2 /s Delivery temperature -10 C to +80 C Grain size max. Ø2 mm Flange Shaft Impeller Intermediate chamber EN-GJS Mechanical seal Bottom for extension tube Intake strainer WC, Carbide, FPM, Stainless steel Contamination max. 50 g/m 3 Direction of rotation clockwise (as viewed looking down on the motor's ventilation side) Tension anchor Pumps bottom Elastomers 1.57 EN-GJL-250 FPM Fluids delivered Emulsions, cooling and cutting oils, cleaning liquids, mild acids Bearings Gap bush (H max < 150 m) Deep groove ball bearing with covering disk POM Mechanical seal (H max > 150 m) WC, Carbide, FPM, Stainless steel ) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

35 l spandaupumpen.com Centrifugal pumps 35 Symbolisierung der verschiedenen Fördermedien stark verunreinigte Fördermedien leicht verunreinigte Fördermedien PXA 18 Immersion pumps, sealless 60 Hz, closed impellers reine Fördermedien k Øm Variation "V" with bottom for extension tube G 2 Øq G2 45 s 45 Variation "C" with intake strainer PXA Ø2 / 4x Ø14 t 125 max. level of fluid min. level of fluid 70 Ø180 Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øq s Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PXA ,9 Y 460 M 4,55 Y 7, , ,2 O 8,6 13, , ,9 P 12,6 19, , Q 17, , ,5 R 21, , G2

36 36 Centrifugal pumps spandaupumpen.com PS 01 Immersion pumps, sealless 50 Hz, closed impellers p [psi] H [m] PS stages 50 Hz PS stages Features Vertical multistage coolant pump For delivery of clean, polluted and viscous types of fluids Delivery head 1) PS stages PS stages PS stages PS stages PS/PSL Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G PS stages Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max 1250 l/min Delivery head H max 105 m Flange Mechanical seal NBR Immersion depth t max 670 mm Shaft Extension tube Kinematic viscosity max. 30 mm 2 /s Delivery temperature 0 C to +80 C Grain size max. Ø4 mm Contamination max. 8,2 kg/m 3 Direction of rotation clockwise (as viewed looking down on the motor's ventilation side) Impeller Intermediate chamber Bearings Bushing Pumps bottom Deep groove ball bearing with covering disk Sintered iron Fluids delivered Emulsions, cooling and cutting oils, Water with rustproofing additives, heat carrier oil 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

37 spandaupumpen.com Centrifugal pumps 37 PS 01 Immersion pumps, sealless 50 Hz, closed impellers k Ø m G2 Ø l Ø2 / 4x Ø14 max. level of fluid t min. level of fluid PS/PSL Ø180 Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PS PSL H 1,1 4,07/2, K 2,2 7,15/4, / L 3,0 10,0/5, M 4,0 13,0/7, N 5,5 11, O 7,5 14, G2

38 38 Centrifugal pumps spandaupumpen.com PS 01 Immersion pumps, sealless 60 Hz, closed impellers p [psi] H [m] PS stages 60 Hz PS stages Features Vertical multistage coolant pump For delivery of clean, polluted and viscous types of fluids Delivery head 1) PS stages PS stages PS stages PS stages PS/PSL Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G PS stages Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max Delivery head H max Immersion depth t max 1250 l/min 105 m 670 mm Flange Shaft Mechanical seal NBR Extension tube Kinematic viscosity max. 30 mm 2 /s Delivery temperature 0 C to +80 C Grain size max. Ø4 mm Contamination max. 8,2 kg/m 3 Direction of rotation clockwise (as viewed looking down on the motor's ventilation side) Impeller Intermediate chamber Bearings Bushing Pumps bottom Deep groove ball bearing with covering disk Sintered iron Fluids delivered Emulsions, cooling and cutting oils, Water with rustproofing additives, heat carrier oil 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

39 spandaupumpen.com Centrifugal pumps 39 PS 01 Immersion pumps, sealless 60 Hz, closed impellers k Ø m G2 Ø l Ø2 / 4x Ø14 max. level of fluid t min. level of fluid PS/PSL Ø180 Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PS PSL H 1,26 4,07/2, K 2,6 7,5/4, / L 3,6 10,1/5, M 4,5 12,7/7, N 6,2 11, Δ O 8,6 14, G2

40 Centrifugal pumps spandaupumpen.com PS 03 Immersion pumps, sealless 50 Hz, closed impellers p [psi] H [m] PS ) 7-stages 50 Hz PS ) 6-stages 80 PS stages PS/PSL Features Vertical multistage coolant pump For delivery of clean, polluted and viscous types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G2 Delivery head 1) PS stages PS stages PS stages PS stages Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max Delivery head H max Immersion depth t max 1250 l/min 105 m 670 mm Flange Shaft Mechanical seal NBR Extension tube Kinematic viscosity max. 30 mm 2 /s Delivery temperature 0 C to +80 C Grain size max. Ø4 mm Contamination max. 8,2 kg/m 3 Direction of rotation clockwise (as viewed looking down on the motor's ventilation side) Impeller Intermediate chamber Bearings Bushing Pumps bottom Deep groove ball bearing with covering disk Sintered iron Fluids delivered Emulsions, cooling and cutting oils, Water with rustproofing additives, heat carrier oil 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate. 2) Frame sizes PS/PSL 0306 and 0307 available on request.

41 spandaupumpen.com Centrifugal pumps 41 PS 03 Immersion pumps, sealless 50 Hz, closed impellers k Ø m G2 Ø l Ø2 / 4x Ø14 max. level of fluid t min. level of fluid PS/PSL Ø180 Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PS PSL K 2,2 7,15/4, / M 4,0 13,0/7, N 5,5 11, O 7,5 14, Y 9,5 17, * 06* P * 600 Q G2 * Frame sizes PS/PSL 0306 and 0307 available on request.

42 42 Centrifugal pumps spandaupumpen.com PS 03 Immersion pumps, sealless 60 Hz, closed impellers p [psi] H [m] PS ) 7-stages 60 Hz PS ) 6-stages 80 PS stages PS/PSL Features Vertical multistage coolant pump For delivery of clean, polluted and viscous types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G2 Delivery head 1) PS stages PS stages PS stages PS stages Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design Variations Delivery rate Q max Delivery head H max Immersion depth t max 1250 l/min 105 m 670 mm Flange Shaft Mechanical seal NBR Extension tube Kinematic viscosity max. 30 mm 2 /s Delivery temperature 0 C to +80 C Grain size max. Ø4 mm Contamination max. 8,2 kg/m 3 Direction of rotation clockwise (as viewed looking down on the motor's ventilation side) Impeller Intermediate chamber Bearings Bushing Pumps bottom Deep groove ball bearing with covering disk Sintered iron Fluids delivered Emulsions, cooling and cutting oils, Water with rustproofing additives, heat carrier oil 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate. 2) Frame sizes PS/PSL 0306 and 0307 available on request.

43 spandaupumpen.com Centrifugal pumps 43 PS 03 Immersion pumps, sealless 60 Hz, closed impellers k Ø m G2 Ø l Ø2 / 4x Ø14 max. level of fluid t min. level of fluid PS/PSL Ø180 Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PS PSL K 2,6 7,5/4, / M 4,5 12,7/7, N 6,2 11, O 8,6 14, Δ Y 11,0 17, * 06* P 12, * 600 Q G2 * Frame sizes PS/PSL 0306 and 0307 available on request.

44 44 Centrifugal pumps spandaupumpen.com Symbolisierung der verschiedenen Fördermedien PMS 05, 06, 08, 10 Immersion pumps, sealless 50 Hz, open impellers stark verunreinigte Fördermedien leicht verunreinigte Fördermedien reine Fördermedien p [psi] 10 H [m] 7, Hz 9 6,5 8 6,0 5, , Delivery head 1) 6 5 4,5 4,0 3, Features Vertical multistage pump Connecting dimensions according to DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G3/ ,0 2,5 2,0 1,5 1,0 0, Q [l/min] PMS Unventilated motor 0 2,5 5,0 7,5 10,0 12,5 15,0 17,5,0 22,5 Q [USgpm] Delivery rate 1) Technical data Mechanical design Variations Delivery rate Q max 100 l/min Delivery head H max Immersion depth t max 7 m 350 mm Kinematic viscosity max. mm 2 /s Delivery temperature "P" "G" Grain size Contamination 0 C to 60 C 0 C to 80 C max. Ø5 mm max. 10 kg/m³ Flange and steel Shaft Impeller Intermediate chamber Bushes Pumps bottom material "P" POM PTFE graphite POM Bottom with extension tube "V" Impeller material "G" Bottom standard design "G" Splash ring material "G" Direction of rotation anti-clockwise (as viewed looking down on the motor's ventilation side) Splash ring material "P" NBR Fluids delivered Various industrial use fluids, emulsions, also with chemical additives, oils, water with corrosion protection additive, water colors, heat transfer oils 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

45 spandaupumpen.com Centrifugal pumps 45 PMS l Symbolisierung der verschiedenen Fördermedien PMS 05, 06, 08, 10 Immersion pumps, sealless 50 Hz, open impellers stark verunreinigte Fördermedien leicht verunreinigte Fördermedien reine Fördermedien øm Variation "V" with bottom for extension tube k a G ¾ ø ø115 / 4 ø7 ø100 b max. level of fluid t min. level of fluid 45 ø100 Electrical data, dimensions and weights at 50 Hz Series PMS Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øa b Weight [kg] 230/0 A 0,09 0,46/0, ,4 5, /0 A 0,09 0,46/0, ,4 5, /0 B 0,12 0,50/0, ,4 5, /0 C 0,18 0,83/0, ,3 7,3 55 Sonic Pressure pressure port [dba] (DIN ISO 228) G¾

46 46 Centrifugal pumps spandaupumpen.com PMS 05, 06, 08, 10 Immersion pumps, sealless 60 Hz, open impellers p [psi] 10 H [m] 7, Hz 9 6,5 8 6,0 5, , Delivery head 1) 6 5 4,5 4,0 3, Merkmale Vertical multistage pump Connecting dimensions according to DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G3/ ,0 2,5 2,0 1,5 1,0 0, Q [l/min] PMS Unventilated motor 0 2,5 5,0 7,5 10,0 12,5 15,0 17,5,0 22,5 Q [USgpm] Delivery rate 1) Technical data Mechanical design Variations Delivery rate Q max 100 l/min Delivery head H max Immersion depth t max 7 m 350 mm Kinematic viscosity max. mm 2 /s Delivery temperature "P" "G" Grain size Contamination 0 C bis 60 C 0 C bis 80 C max. Ø5 mm max. 10 kg/m³ Flange and steel Shaft Impeller Intermediate chamber Bushes Pumps bottom material "P" POM PTFE graphite POM Bottom with extension tube "V" Impeller material "G" Bottom standard design "G" Splash ring material "G" Direction of rotation anti-clockwise (as viewed looking down on the motor's ventilation side) Splash ring material "P" NBR Fluids delivered Various industrial use fluids, emulsions, also with chemical additives, oils, water with corrosion protection additive, water colors, heat transfer oils 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

47 spandaupumpen.com Centrifugal pumps 47 PMS 05, 06, 08, 10 Immersion pumps, sealless 60 Hz, open impellers PMS l øm Variation "V" with bottom for extension tube k a G ¾ ø ø115 / 4 ø7 ø100 b max. level of fluid t min. level of fluid 45 ø100 Electrical data, dimensions and weights at 60 Hz Series PMS Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øa b Weight [kg] 265/460 A 0,09 0,46/0, ,4 5, /460 A 0,09 0,46/0, ,4 5, /460 B 0,12 0,50/0, ,4 5, /460 C 0,18 0,83/0, ,3 7,3 55 Sonic Pressure pressure port [dba] (DIN ISO 228) G¾

48 48 Centrifugal pumps spandaupumpen.com PMS 25 Immersion pumps, sealless 50 Hz, open impellers p [psi] 64 H [m] Hz Merkmale Vertical multistage pump Delivery head 1) Connecting dimensions according to DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G1¼ Q [l/min] PMS Q [USgpm] Delivery rate 1) Technical data Mechanical design Variations Delivery rate Q max 250 l/min Delivery head H max Immersion depth t max 45 m 550 mm Kinematic viscosity max. mm 2 /s Delivery temperature "P" "G" Grain size 0 C bis 60 C 0 C bis 80 C max. Ø8 mm Contamination max. 1,5% (proportion by weight) Direction of rotation anti-clockwise (as viewed looking down on the motor's ventilation side) Flange and steel Shaft Impeller Intermediate chamber Bushes Pumps bottom material "P" Splash ring material "P" POM PTFE graphite POM NBR Bottom with extension tube "V" Impeller material "G" Bottom standard design "G" Splash ring material "G" Fluids delivered Various industrial use fluids, emulsions, also with chemical additives, oils, water with corrosion protection additive, water colors, heat transfer oils 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

49 spandaupumpen.com Centrifugal pumps 49 PMS 25 Immersion pumps, sealless 50 Hz, open impellers k øm PMS 30 a G1 ¼ t l Variation "V" with bottom for extension tube ø50 ø160 / 4xø7 ø1 b max. level of fluid min. level of fluid 50 ø1 Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øa b Weight [kg] Sonic Pressure pressure port [dba] (DIN ISO 228) /0 F 0,55 2,06/1, ,2 16, PMS /0 J 1,5 4,95/2, ,0 27,5 59 G1¼ /0 J 1,5 4,95/2, ,5 29, /0 L 3,0 10,0/5, ,0 65

50 50 Centrifugal pumps spandaupumpen.com PMS 25 Immersion pumps, sealless 60 Hz, open impellers p [psi] 64 H [m] Hz Merkmale Vertical multistage pump Delivery head 1) Connecting dimensions according to DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G1¼ Q [l/min] PMS Q [USgpm] Delivery rate 1) Technical data Mechanical design Variations Delivery rate Q max 250 l/min Delivery head H max Immersion depth t max 45 m 550 mm Kinematic viscosity max. mm 2 /s Delivery temperature "P" "G" Grain size 0 C bis 60 C 0 C bis 80 C max. Ø8 mm Contamination max. 1,5% (proportion by weight) Direction of rotation anti-clockwise (as viewed looking down on the motor's ventilation side) Flange and steel Shaft Impeller Intermediate chamber Bushes Pumps bottom material "P" Splash ring material "P" POM PTFE graphite POM NBR Bottom with extension tube "V" Impeller material "G" Bottom standard design "G" Splash ring material "G" Fluids delivered Various industrial use fluids, emulsions, also with chemical additives, oils, water with corrosion protection additive, water colors, heat transfer oils 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

51 spandaupumpen.com Centrifugal pumps 51 PMS 25 Immersion pumps, sealless 60 Hz, open impellers k øm PMS 30 a G1 ¼ t l Variation "V" with bottom for extension tube ø50 ø160 / 4xø7 ø1 b max. level of fluid min. level of fluid 50 ø1 Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øa b Weight [kg] Sonic Pressure pressure port [dba] (DIN ISO 228) /460 F 0,55 1,75/1, ,2 16, PMS /460 J 1,5 4,33/2, ,0 27,5 59 G1¼ /460 J 1,5 4,33/2, ,5 29, /460 L 3,0 8,65/5, ,0 65

52 52 Centrifugal pumps spandaupumpen.com PMS 30, Immersion pumps, sealless 50 Hz, open impellers p [psi] 32 H [m] Hz Merkmale Vertical multistage pump Delivery head 1) Connecting dimensions according to DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G1¼ Q [l/min] PMS Q [USgpm] Delivery rate 1) Technical data Mechanical design Variations Delivery rate Q max 0 l/min Delivery head H max Immersion depth t max 14 m 560 mm Kinematic viscosity max. mm 2 /s Delivery temperature "P" "G" Grain size 0 C bis 60 C 0 C bis 80 C max. Ø8 mm Contamination max. 1,5% (proportion by weight) Direction of rotation anti-clockwise (as viewed looking down on the motor's ventilation side) Flange and steel Shaft Impeller Intermediate chamber Bushes Pumps bottom material "P" Splash ring material "P" POM PTFE graphite POM NBR Bottom with extension tube "V" Impeller material "G" Bottom standard design "G" Splash ring material "G" Fluids delivered Various industrial use fluids, emulsions, also with chemical additives, oils, water with corrosion protection additive, water colors, heat transfer oils 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

53 l spandaupumpen.com Centrifugal pumps 53 PMS 30, Immersion pumps, sealless 50 Hz, open impellers øm Variation "V" with bottom for extension tube k ø50 t 30 a G1¼ ø160 / 4xø7 ø1 b max. level of fluid min. level of fluid 50 ø1 PMS Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øa b Weight [kg] Sonic Pressure pressure port [dba] (DIN ISO 228) /0 G 0,75 2,56/1, ,2 16,3 59 PMS G1¼ /0 J 1,5 4,95/2, ,0 26,0 65

54 54 Centrifugal pumps spandaupumpen.com PMS 30, Immersion pumps, sealless 60 Hz, open impellers p [psi] 32 H [m] Hz Merkmale Vertical multistage pump Delivery head 1)) Connecting dimensions according to DIN EN For delivery of slightly contaminated types of fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate and designed with internal thread G1¼ Q [l/min] PMS Q [USgpm] Delivery rate 1) Technical data Mechanical design Variations Delivery rate Q max 0 l/min Delivery head H max Immersion depth t max 14 m 560 mm Kinematic viscosity max. mm 2 /s Delivery temperature "P" "G" Grain size 0 C bis 60 C 0 C bis 80 C max. Ø8 mm Contamination max. 1,5% (proportion by weight) Direction of rotation anti-clockwise (as viewed looking down on the motor's ventilation side) Flange and steel Shaft Impeller Intermediate chamber Bushes Pumps bottom material "P" Splash ring material "P" POM PTFE graphite POM NBR Bottom with extension tube "V" Impeller material "G" Bottom standard design "G" Splash ring material "G" Fluids delivered Various industrial use fluids, emulsions, also with chemical additives, oils, water with corrosion protection additive, water colors, heat transfer oils 1) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

55 spandaupumpen.com Centrifugal pumps 55 l PMS 30, Immersion pumps, sealless 60 Hz, open impellers øm Variation "V" with bottom for extension tube k ø50 PMS t 30 a G1¼ ø160 / 4xø7 ø1 b max. level of fluid min. level of fluid 50 ø1 Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Øa b Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) /460 G 0,75 2,27/1, ,2 bis 16, PMS G1¼ /460 J 1,5 4,33/2, ,0 bis 26,

56 56 Centrifugal pumps spandaupumpen.com PSH Immersion pumps, sealless 50 Hz, singlestage, open impellers p [psi] H [m] PSH 85 1-stage 30 PSH 80 1-stage 50 Hz PSH 60 1-stage Features Delivery head 1) 15 Vertical singlestage centrifugal pump For delivery of for highly contaminated fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate Pressure port is designed with internal thread G1¼ (single stage) Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design PSH Delivery rate Q max 860 l/min Delivery head H max 32 m Flange Immersion depth t max 550 mm Shaft Kinematic viscosity max. 30 mm 2 /s Impeller Delivery temperature Grain size Contamination Direction of rotation Fluids delivered -30 C to +80 C max. Ø8 mm max. 9,5 kg/m³ clockwise (as viewed looking down on the motor's ventilation side) Emulsions, cooling and cutting oils, water with antirust additive, heat transfer oils Intermediate chamber Intermediate part Pumps bottom Aluminum (Al Cu Mg Pb F 38) Spray ring ) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

57 spandaupumpen.com Centrifugal pumps 57 PSH Immersion pumps, sealless 50 Hz, singlestage, open impellers l k øm ø245 ø270/4 ø G1¼ max. level of fluid t min. level of fluid 90 ø50 ø275 Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PSH ,5 230/0 L 3,0 10,0/5, , G1¼ PSH ,2 Δ 0 N 5,5 Δ 11, , G1¼ ,2 Δ 0 N 5,5 Δ 11, , G1¼

58 58 Centrifugal pumps spandaupumpen.com PSH Immersion pumps, sealless 60 Hz, singlestage, open impellers p [psi] H [m] PSH 85 1-stage 30 PSH 80 1-stage 60 Hz PSH 60 1-stage Features Delivery head 1) 15 Vertical singlestage centrifugal pump For delivery of for highly contaminated fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate Pressure port is designed with internal thread G1¼ (single stage) Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design PSH Delivery rate Q max 860 l/min Delivery head H max 32 m Flange Immersion depth t max 550 mm Shaft Kinematic viscosity max. 30 mm 2 /s Impeller Delivery temperature Grain size Contamination Direction of rotation Fluids delivered -30 C to +80 C max. Ø8 mm max. 9,5 kg/m³ clockwise (as viewed looking down on the motor's ventilation side) Emulsions, cooling and cutting oils, water with antirust additive, heat transfer oils Intermediate chamber Intermediate part Pumps bottom Aluminum (Al Cu Mg Pb F 38) Spray ring

59 spandaupumpen.com Centrifugal pumps 59 PSH Immersion pumps, sealless 60 Hz, singlestage, open impellers l k øm ø245 ø270/4 ø G1¼ max. level of fluid t min. level of fluid 90 ø50 ø275 Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PSH ,5 265/460 L 3,6 10,0/5, , G1¼ PSH ,2 Δ 460 N 6,2 Δ 11, , G1¼ ,2 Δ 460 N 6,2 Δ 11, , G1¼

60 60 Centrifugal pumps spandaupumpen.com PSH Immersion pumps, sealless 50 Hz, dualstage, open impellers p [psi] H [m] 50 Hz PSH 00 2-stages PSH 95 2-stages Features Delivery head 1) 30 Vertical multistage centrifugal pump For delivery of for highly contaminated fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate Pressure port is designed with internal thread G1½ (dual stages) Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design PSH Delivery rate Q max 1000 l/min Delivery head H max 54 m Flange Immersion depth t max 350 mm Shaft Kinematic viscosity max. 30 mm 2 /s Impeller Delivery temperature Grain size Contamination Direction of rotation Fluids delivered -30 C to +80 C max. Ø8 mm max. 9,5 kg/m³ clockwise (as viewed looking down on the motor's ventilation side) Emulsions, cooling and cutting oils, water with antirust additive, heat transfer oils Intermediate chamber Intermediate part Pumps bottom Aluminum (Al Cu Mg Pb F 38) Spray ring ) Data for viscosity of ~1 mm²/s at a density of ~1 kg/dm³. Minimum volumetric flow: 5 to 10 % of nominal delivery rate.

61 spandaupumpen.com Centrifugal pumps 61 l PSH Immersion pumps, sealless 50 Hz, dualstage, open impellers k øm ø t 150 ø270/4 ø11 max. level of fluid G1 ½ min. level of fluid ø65 ø239 Electrical data, dimensions and weights at 50 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PSH Δ 0 O 7,5 Δ 14, , PSH G1½ Δ 0 P 11,0 Δ ,

62 62 Centrifugal pumps spandaupumpen.com PSH Immersion pumps, sealless 60 Hz, dualstage, open impellers p [psi] H [m] 60 Hz PSH 00 2-stages PSH 95 2-stages Features Delivery head 1) 30 Vertical multistage centrifugal pump For delivery of for highly contaminated fluids Installation direcly into the reservoir Pressure port is located above the reservoir plate Pressure port is designed with internal thread G1½ (dual stages) Q [l/min] Q [USgpm] Delivery rate 1) Technical Data Mechanical design PSH Delivery rate Q max 1000 l/min Delivery head H max 54 m Flange Immersion depth t max 350 mm Shaft Kinematic viscosity max. 30 mm 2 /s Impeller Delivery temperature Grain size Contamination Direction of rotation Fluids delivered -30 C to +80 C max. Ø8 mm max. 9,5 kg/m³ clockwise (as viewed looking down on the motor's ventilation side) Emulsions, cooling and cutting oils, water with antirust additive, heat transfer oils Intermediate chamber Intermediate part Pumps bottom Aluminum (Al Cu Mg Pb F 38) Spray ring

63 spandaupumpen.com Centrifugal pumps 63 l PSH Immersion pumps, sealless 60 Hz, dualstage, open impellers k øm ø t 150 ø270/4 ø11 max. level of fluid G1 ½ min. level of fluid ø65 ø239 Electrical data, dimensions and weights at 60 Hz Series Type of pump Frame size Stages Immersion depth t [mm] Voltage / Y U [V] Motor index Rated motor values Output P N [kw] Current / Y l N [A] Speed n N [min -1 ] Dimensions [mm] Øm k l Weight [kg] Sonic pressure [dba] Pressure port (DIN ISO 228) PSH Δ 460 O 8,6 Δ 14, , PSH G1½ Δ 460 P 12,5 Δ ,

64 64 Centrifugal pumps spandaupumpen.com PRG Immersion pumps, sealless Order key PRG Series P R G Frame size 06 Stages To determine the desired number of stages the corresponding characteristics has to be used. 01 = 1-stage = 4-stages s P = POM (standard) Seal B = gap bush (standard) Pump design S = standard design I = intruder Immersion depth in To determine the desired immersion depth the appropriate table "Electrical data, dimensions and weights" has to be used. 1 = 1 mm... 3 = 3 mm Motorindex To determine the desired immersion depth the appropriate table "Electrical data, dimensions and weights" has to be used. Example: E = 0,37 kw Power supply 01 = 230/0 V at 50 Hz 265/460 V at 60Hz 05 = standard for Europe 230/0 V 50 Hz... further designs on request Motor index AA = standard to 0,55 kw (insulation class F, IP 54, 2-pole) EA = single-phase motor... further designs on request Order example: PRG0602PBS160B05AA Series:: PRG, frame size: 06, 02-stages, material: P POM plastic, seal:: B bush, Pump design: S standard design, immersion depth: 160 mm, Motor index: B 0,12 kw, Power supply: /0 V 50 Hz; Motor design: AA standard

65 spandaupumpen.com Centrifugal pumps 65 PRK Immersion pumps, hydrostatic sealing Order key Series P R K Frame size 03 Stages To determine the desired number of stages the corresponding characteristics has to be used. 01 = 1 stage = 5 stages PRK s P = POM (standard)) Seal B = gap bush (standard) Pump design S = standard design (bottom prepared for extension tube) C = bottom equipped with intake strainer Immersion depth in mm To determine the desired immersion depth the appropriate table "Electrical data, dimensions and weights" has to be used. 090 = 90 mm = 410 mm Motor index To determine the desired motor index the appropriate table "Electrical data, dimensions and weights" has to be used. Example: E = 0,55 kw Power supply 01 = 230/0 V bei 50 Hz; 265/460 V bei 60Hz 05 = 230/0 V 50 Hz Further designs on request. Motorausführung AA = standard to 0,55 kw (insulation class F, IP 54, 2-pole,) BA = standard from 0,75 kw (insulation class F, IP 54, 2-pole,, IE2) Further designs on request. Order example: PRK0304PBS255G05BA Series:: PRK, frame size: 03, 4 stages,, material: P POM plastic, seal: B gap bush, pump design: S standard design, immersion depth: 225 mm, motor index:: G 0,75 kw, power supply: /0 V 50 Hz; Motor design: BA standard (IE2)

66 66 Centrifugal pumps spandaupumpen.com PSR Immersion pumps, sealless Order key P S R Series Frame size 02 = 2 m³/h (nominal delivery rate) 04 = 4 m³/h (nominal delivery rate) 06 = 6 m³/h (nominal delivery rate) PSR Stages To determine the desired number of stages the corresponding characteristics has to be used. 01 = 1-stage = 30-stages s G = gray cast iron (standard) C = GG with chemical surface sealing T = GG coated with paint Seal B = gap bush (H max < 150 m) G = machanical seal (H max > 150 m) Pump design S = standard design V = bottom for extension tube C = bottom equipped with intake strainer Immersion depth in mm To determine the desired immersion depth the appropriate table "Electrical data, dimensions and weights" has to be used. 122 = 122 mm = 739 mm Motor index To determine the desired motor index the appropriate table "Electrical data, dimensions and weights" has to be used. Example: E = 0,37 kw Power supply 01 = 230 /0 V at 50 Hz (to 4 kw) 265 /460 V at 60 Hz (to 4,6 kw) 02 = 0 V at 50 Hz (from 5,5 kw) 460 V at 60 Hz (from 6,3 kw) 05 = Standard for Europe 230/0 V at 50 Hz (from 4 kw) 0 V at 50 Hz (from 4 kw)... further designs on request Motor design AA = standard to 0,55 kw (insulation class F, IP 54, 2-pole) BA = standard from 0,75 kw (insulation class F, IP 54, 2-pole, IE2)... further designs on request Order example: PSR0218GBS481J01BA Series: PSR, Frame size: 02, 18-stages, : G grey cast iron, Seal: B gap bush, Pump design: S standard design, Immersion depth: 481 mm, Motor index: J 1,5 kw, Power supply: /0 V 50 Hz; 265/460 V 60Hz, Motor design: BA standard form 0,75 kw

67 spandaupumpen.com Centrifugal pumps 67 PXA 10/18 Immersion pumps, sealless Order key Series Frame size P X A To determine the fram size the corresponding characteristics has to be used. 10, 18 Stages To determine the desired number of stages the corresponding characteristics has to be used. 02 = 2-stages... = -stages s G = gray cast iron (standard) PXA Seal B = gap bush G = machanical seal Pump design S = standard design V = bottom for extension tube C = bottom for intake strainer Immersion depth in mm To determine the desired immersion depth the appropriate table "Electrical data, dimensions and weights" has to be used. 194 = 194 mm = 692 mm Motor index To determine the desired motor index the appropriate table "Electrical data, dimensions and weights" has to be used. Example: J = 1,5 kw Power supply 01 = 230 /0 V at 50 Hz (to 4 kw) 265 /460 V at 60 Hz (to 4,6 kw) 02 = 0 V at 50 Hz (from 5,5 kw) 460 V at 60 Hz (from 6,3 kw) 05 = Standard for Europe 230/0 V at 50 Hz (from 4 kw) 0 V at 50 Hz (from 5,5 kw)... further designs on request Motor design BA = standard (insulation class F, IP 54, 2-pole, IE2)... further designs on request CA = standard (insulation class F, IP 54, 2-pole, IE3)... further designs on request Order example: PXA1009GBS383M05BA Series: PXA, Frame size: 10, 09-stages, : G grey cast iron, Seal: B gap bush, Pump design: S standard design, Immersion depth: 383 mm, Motor index: M 4,0 kw, Power supply: /0 V 50 Hz (< 4 kw), Motor design: CA Standard (IE3) * All data and measurements refer to the IE3-motors.

68 68 Centrifugal pumps spandaupumpen.com PS/PSL Immersion pumps, sealless Order key Series PS- = Standard design PSL = "Slurp" for air-polluted liquids Frame size To determine the frame size the corresponding characteristics has to be used. 01, 03 Stages To determine the desired number of stages the corresponding characteristics has to be used. 01 = 1-stages = 7-stages s G = gray cast iron (standard) PS/PSL Seal B = gap bush (standard) Pump design S = standard design V = bottom for extension tube Immersion depth in mm 250 = 250 mm = 670 mm Motor index To determine the desired motor index the appropriate table "Electrical data, dimensions and weights" has to be used. Example: J = 1,5 kw Power supply 01 = 230 /0 V at 50 Hz (to 4 kw) 265 /460 V at 60 Hz (to 4,6 kw) 02 = 0 V at 50 Hz (from 5,5 kw) 460 V at 60 Hz (from 6,3 kw) 05 = Standard for Europe 230/0 V at 50 Hz (from 4 kw) 0 V at 50 Hz (from 4 kw)... further designs on request Motor design BA = standard (insulation class F, IP 54, 2-pole, IE2)... further designs on request Order example: PS-0104GBS460M01BA Series: PS, Frame size: 01, 04-stages, : G grey cast iron, Seal: B gap bush, Pump design: S standard design, Immersion depth: 460 mm, Motor index: M 4,0 kw, Power supply: /0 V 50 Hz, 265/460 V 60 Hz, Motor design: BA standard (IE2)

69 spandaupumpen.com Centrifugal pumps 69 PMS Immersion pumps, sealless Order key Series Frame size P M S To determine the fram size the corresponding characteristics has to be used. 05, 06, 08, 10, 25, 30, Stages To determine the desired number of stages the corresponding characteristics has to be used. 01 = 1-stage = 4-stages s P = plastic (Standard) G = gray cast iron Seal B = gap bush Pump design S = standard design V = bottom for extension tube Immersion depth in mm To determine the desired immersion depth the appropriate table "Electrical data, dimensions and weights" has to be used. 90 = 90 mm = 560 mm PMS Motor index To determine the desired motor index the appropriate table "Electrical data, dimensions and weights" has to be used. Example: H = 1,1 kw Power supply 01 = 230 /0 V at 50 Hz 265 /460 V at 60 Hz 05 = Standard für Europa 230/0 V at 50 Hz... further designs on request Motor design AA = standard up to 0,55 kw (insulation class F, IP 54, 2-pole) BA = standard from 0,75 kw (insulation class F, IP 54, 2-pole, IE2)... further designs on request Order example: PMS01GBS280J01BA Series: PMS, Frame size:, 01-stage, : G grey cast iron, Seal: B gap bush, Pump design: S standard design, Immersion depth: 280 mm, Motor index: J 1,5 kw, Power supply: /0 V at 50 Hz, 265/460 V at 60 Hz, Motor design: BA Standard (IE2) * All data and measurements refer to the IE2-motors.

70 70 Centrifugal pumps spandaupumpen.com PSH Immersion pumps, sealless Order key P S H Series Frame size To determine the desired frame size the corresponding characteristics has to be used. 60 = max. 600 l/min 80 = max. 800 l/min 85 = max. 850 l/min 95 = max. 950 l/min 00 = max l/min Stages To determine the desired number of stages the corresponding characteristics has to be used. 01 = 1 stages 02 = 2 stages s G = gray cast iron (standard) Seal O = sealless (standard) Pump design S = standard design Immersion depth in mm 300 = 300 mm = 550 mm PSH Motor index To determine the desired motor index the appropriate table "Electrical data, dimensions and weights" has to be used. Example: L = 3,0 kw Power supply 01 = 230 /0 V at 50 Hz (to 4 kw) 265 /460 V at 60 Hz (to 4,6 kw) 02 = 0 V at 50 Hz (from 5,5 kw) 460 V at 60 Hz (from 6,3 kw) 05 = Standard for Europe 230/0 V at 50 Hz (from 4 kw) 0 V at 50 Hz (from 4 kw)... further designs on request Motor design BA = standard (insulation class F, IP 54, 2-pole, IE2) Further designs on request. Order example: PSH8501GOS550N02BA Series: PSH, Frame size: 85, 01 stage, : G grey cast iron, Seal: O gap bush, Pump design: S standard design, Immersion depth: 550 mm, Motor index: N 5,5 kw, Power supply: 02 Δ0 V 50 Hz, Δ460 V 60 Hz, Motor design: BA Standard (IE2)

71 Notes

72 The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of use of the information contained herein. SKF Lubrication Systems Germany GmbH Product department Spandau Pumps Motzener Strasse 35/ Berlin Germany PF Berlin Germany Tel. +49 (0) Fax +49 (0) SpandauPumpen@skf.com This brochure was presented by: EN 03/17 Subject to chane without notice!

PSR Centrifugal pumps

PSR Centrifugal pumps 1 65 EN Centrifugal pumps Technical data Delivery rate Q max = 180 l/min Delivery head H max = 255 m Temperature range T = -10 C to +80 C Kinematic viscosity ν max = mm 2 /s Quality Management DIN EN ISO

More information

PS/PSL Centrifugal pumps

PS/PSL Centrifugal pumps 1 14 EN Centrifugal pumps Technical Data Delivery rate Q max = 1250 l/min Delivery head H max = 110 m Delivery temperature T = 0 C to + C Kinematic viscosity ν max = 30 mm 2 /s Quality Management DIN EN

More information

PRA Centrifugal pumps

PRA Centrifugal pumps 1 6001-EN PRA Centrifugal pumps Technical data Delivery rate Q max = 130 l/min Delivery head H max = 30 m Temperature range T = 5 C to 60 C Kinematic viscosity ν max = mm 2 /s Quality Management DIN EN

More information

PMS Centrifugal pumps

PMS Centrifugal pumps 1 6033 EN Centrifugal pumps Technical data Delivery rate Q max = 400 l/min Delivery head H max = 45 m Delivery temperature T = 0 C bis +0 C Kinematic viscosity ν max = 20 mm 2 /s Quality Management DIN

More information

Electric Immersion Pumps PXA and PXK, sealless

Electric Immersion Pumps PXA and PXK, sealless 1-6062-US PXA and PXK, sealless MQUALITY MANAE ENT Cooling and lubricating with high-pressure... Centrifugal pumps for delivery pressures up to 25 bars Technical data Delivery rate Q max = 185 l/min Delivery

More information

PS/PSL Centrifugal pumps

PS/PSL Centrifugal pumps 1 14 EN Centrifugal pumps Technical Data Delivery rate Q max = 1250 l/min Delivery head H max = 110 m Delivery temperature T = 0 C to + C Kinematic viscosity ν max = 30 mm 2 /s Quality Management DIN EN

More information

Immersion Pumps PS and PSL ( Slurp Pump ) sealless

Immersion Pumps PS and PSL ( Slurp Pump ) sealless Immersion Pumps PS and PSL ( Slurp Pump ) sealless 1-6014-US Centrifugal pumps of metal for clean, polluted and viscous fluids Technical data Delivery rate Q max = 1250 l/min Delivery head H max = 105

More information

Immersion Pumps PMS and PMS-T sealless

Immersion Pumps PMS and PMS-T sealless Immersion Pumps PMS and PMS-T sealless 1-6033-EN Centrifugal pumps of metal with high resistance to wear for diverse industrial fluids Technical data Delivery rate Q max = 400 l/min Delivery head H max

More information

Immersion Pumps PRG sealless

Immersion Pumps PRG sealless Immersion Pumps PRG sealless 1-6007-US Centrifugal pumps of plastic for clear or turbid fluids Technical data Delivery rate Q max = 60 l/min Delivery head H max = 32 m Temperature range 20 C to +60 C Product

More information

Electric Immersion Pumps PRT and PRA, sealless

Electric Immersion Pumps PRT and PRA, sealless PRT and, sealless MQUALITY MANAGE ENT Centrifugal pumps of plastic for a wide variety of industrial fluids Technical data Delivery rate Q max = 20 l/min Delivery head H max = 32 m Temperature range -30

More information

PAB Atex-certified centrifugal pumps

PAB Atex-certified centrifugal pumps 1 6036 EN PAB Atex-certified centrifugal pumps Technical data Delivery rate Q max = 305 l/min Delivery head H max = 20 m Temperature range 0 C to +60 C Quality Management DIN EN ISO 9001: 2008 Environmental

More information

LMP screw pumps for delivery pressures up to 120 bar

LMP screw pumps for delivery pressures up to 120 bar 1 64 EN LM screw pumps for delivery pressures up to 12 bar Technical data Delivery rate max. = 67 l/min Delivery pressure p max. = 12 bar Temperature range C to +8 C Kinematic viscosity 1 to 2 mm 2 /s

More information

Electric Immersion Pumps PT sealless EN

Electric Immersion Pumps PT sealless EN Electric Immersion Pumps PT sealless 1 6017 EN 1 6017 US Peripheral impeller pumps of high tech plastic for clean fluids Technical data Delivery rate Q max = 23 l/min Delivery head H max = 35 m Temperature

More information

Company name: Created by: Phone: Note! Product picture may differ from actual product

Company name: Created by: Phone: Note! Product picture may differ from actual product Date: 13/03/2017 Tender Text Note! Product picture may differ from actual product Product No.: 98993055 MTH4-5/5 A-W-A-AQQV Multistage, immersible, self-priming, centrifugal pump for vertical installation

More information

SF6. EBARA PUMPS EUROPE S.p.A. SUBMERSIBLE PUMPS. Page - CONTENTS 100

SF6. EBARA PUMPS EUROPE S.p.A. SUBMERSIBLE PUMPS. Page - CONTENTS 100 SPECIFICATIONS Page - CONTENTS 100 - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART 202 SELECTION CHART 203 PERFORMANCE CHART R10 204 PERFORMANCE CHART R13 205 PERFORMANCE CHART S25 206 PERFORMANCE

More information

SF6. EBARA PUMPS EUROPE S.p.A. SUBMERSIBLE PUMPS. Page - CONTENTS 100

SF6. EBARA PUMPS EUROPE S.p.A. SUBMERSIBLE PUMPS. Page - CONTENTS 100 SPECIFICATIONS Page - CONTENTS 100 - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART 202 SELECTION CHART 203 PERFORMANCE CHART R10 204 PERFORMANCE CHART R13 205 PERFORMANCE CHART S25 206 PERFORMANCE

More information

S4G Series. Technical Guide. 4 submersible pumps

S4G Series. Technical Guide. 4 submersible pumps SG Series Technical Guide submersible pumps SG Series t Index Sectors of application... Technical characteristics SG... 5 Table of materials and identification data... 6 Nominal data... Hydraulic performance

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEALS 303 DIAGRAM AND ELECTRIC CONNECTIONS 304

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEALS 303 DIAGRAM AND ELECTRIC CONNECTIONS 304 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 202 PERFORMANCE CHART A (up to 0.6 kw) 203 PERFORMANCE CHART A (from 0.75 kw up to 1.1 kw) 204 PERFORMANCE CHART A (1.3 kw) 205 PERFORMANCE

More information

Lowara. Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733. SH Series. 60 Hz

Lowara. Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733. SH Series. 60 Hz Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733 SH Series 60 Hz SERIE SH HYDRAULIC PERFORMANCE RANGE AT 60 Hz WEB 10-2006 2 CONTENTS 5 Specifications... 6

More information

Cooling Systems FLKS - 3S/1.0/W... FLKS - 3L/1.0/W DESCRIPTION

Cooling Systems FLKS - 3S/1.0/W... FLKS - 3L/1.0/W DESCRIPTION Cooling Systems FLKS - S/1.0/W... FLKS - L/1.0/W... 1. DESCRIPTION 1.1. APPLICATIONS Cooling circuits: Cooling of AC main drives Cooling of motor spindles on machining centres Cooling of transmission and

More information

Product Data Sheet ACi 4420 HHR

Product Data Sheet ACi 4420 HHR ACi 4420 HHR INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 4 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating Data... 5

More information

Page - CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE DIMENSIONS AND WEIGHT 400 PUMP DRAWING 400 DIMENSION PUMP TABLE 401

Page - CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE DIMENSIONS AND WEIGHT 400 PUMP DRAWING 400 DIMENSION PUMP TABLE 401 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE R10 205 PERFORMANCE CURVE R13 206 PERFORMANCE CURVE S25 207 PERFORMANCE CURVE S32 208 PERFORMANCE

More information

Product designation. Original assembly instructions with associated operating instructions acc. to EC Machinery Directive 2006/42/EC.

Product designation. Original assembly instructions with associated operating instructions acc. to EC Machinery Directive 2006/42/EC. Product designation Centrifugal pump Product series: PR / PRG / PRT / PRA... / HCT... / PRK Original assembly instructions with associated operating instructions acc. to EC Machinery Directive 2006/42/EC

More information

Side channel pumps PN 16 SOH - SOHB. Self-priming centrifugal pumps. Technical description

Side channel pumps PN 16 SOH - SOHB. Self-priming centrifugal pumps. Technical description Side channel pumps PN 16 Self-priming centrifugal pumps SOH - SOHB Technical description Operating data Design Industries Media pumped: Nominal diameter: 1-1 1 /2 Flow rate: 0.3-7.5 m 3 /h Pump head: 5-155

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEAL 303 FITTINGS 304

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEAL 303 FITTINGS 304 CONTENTS 1 Page - SPECIFICATIONS 200 PERFORMANCE RANGE and SELECTION CHART 201 TYPE KEY and CURVES SPECIFICATIONS 202 PERFORMANCE CURVES 32-250/7.56 203 PERFORMANCE CURVES 32-250/9.26 203 PERFORMANCE CURVES

More information

XS8 Series. Technical Guide Submersible electropumps and motors for 8 wells

XS8 Series. Technical Guide Submersible electropumps and motors for 8 wells XS8 Series Technical Guide Submersible electropumps and motors for 8 wells XS8 Series t Index Sectors of application... Technical characteristics... Table of materials and identification data... 6 Hydraulic

More information

COOLING, LUBRICATING, RINSING, MAINTAINING TEMPERATURES.

COOLING, LUBRICATING, RINSING, MAINTAINING TEMPERATURES. 5 Screw Spindle Pumps COOLING, LUBRICATING, RINSING, MAINTAINING TEMPERATURES www.brinkmannpumps.de GB Story Engineering Each Brinkmann Pump is embedded with often many years of research, including internal

More information

Technical data 50 & 60 Hz. Vertical centrifugal pumps Series: DPLHS

Technical data 50 & 60 Hz. Vertical centrifugal pumps Series: DPLHS Technical data 50 & 60 Hz Vertical centrifugal pumps Series: DPLHS 2 Table of Contents 1 Pump introduction 1.1 General... 4 1.2 Model key... 4 1.3 Description of the product... 4 1.4 Operation... 5 1.5

More information

Product Data Sheet 4184 NXHH

Product Data Sheet 4184 NXHH The engineer's choice 4184 NXHH INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating

More information

SCUBA, GS, Z6-ZN6 SERIES

SCUBA, GS, Z6-ZN6 SERIES 4-5 - 6 SUBMERSIBLE ELECTRIC PUMPS 50 Hz SCUBA, GS, Z6-ZN6 SERIES EDITION 02-2006 CONTENTS Scuba Series Specifications... 3 Scuba Series, hydraulic performance range at 50 Hz... 5 Scuba Series, dimensions

More information

Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 201 CURVE SPECIFICATIONS 202 PERFORMANCE CHART IDROGO PERFORMANCE CHART IDROGO

Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 201 CURVE SPECIFICATIONS 202 PERFORMANCE CHART IDROGO PERFORMANCE CHART IDROGO CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 201 CURVE SPECIFICATIONS 202 PERFORMANCE CHART 40 203 PERFORMANCE CHART 80 204 - CONSTRUCTIONS 300 SECTIONAL VIEW 300 SECTIONAL VIEW 301

More information

Product Data Sheet DV5214 NU

Product Data Sheet DV5214 NU The engineer's choice DV5214 NU INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating

More information

Contents. Identification

Contents. Identification Contents Identification Type key Product data Introduction Applications Features and benefits Performance range pole pole Construction Sectional drawing Construction features Test pressure Operating conditions

More information

franklinwater.eu 50 HZ EH - EHsp SERIES HORIZONTAL MULTISTAGE AND SELF-PRIMING PUMPS

franklinwater.eu 50 HZ EH - EHsp SERIES HORIZONTAL MULTISTAGE AND SELF-PRIMING PUMPS franklinwater.eu 5 HZ EH - EHsp SERIES HORIZONTAL MULTISTAGE AND SELF-PRIMING PUMPS INDEX Stainless Steel Horizontal Multistage (EH) and Self-Priming (EHsp) Pumps 2 Family curves 3 Pump identification

More information

EH -EHsp SERIES 50 Hz

EH -EHsp SERIES 50 Hz PRODUCT CATALOG EH -EHsp SERIES 5 Hz HORIZONTAL MULTISTAGE AND SELF-PRIMING PUMPS franklinwater.eu INDEX STAINLESS STEEL HORIZONTAL MULTISTAGE (EH) AND SELF-PRIMING (EHsp) PUMPS... 2 Family curves...3

More information

Product Data Sheet 4118 N/ The engineer's choice

Product Data Sheet 4118 N/ The engineer's choice The engineer's choice 4118 N/12-190 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Electrical Operating Data... 4 3.2 Operating Data - Electrical

More information

GRUNDFOS DATA BOOKLET MTS. Screw pumps 50/60 Hz

GRUNDFOS DATA BOOKLET MTS. Screw pumps 50/60 Hz GRUNDFOS DATA BOOKLET MTS Screw pumps / Hz Contents Introduction MTS 3 Performance range - MTS, Hz 4 Performance range - MTS, Hz 5 Performance range - MTS, Hz 5 General description Main applications 6

More information

Product Data Sheet 4184 NXHH

Product Data Sheet 4184 NXHH The engineer's choice 4184 NXHH INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating

More information

Product Data Sheet ACi 4420 MLR

Product Data Sheet ACi 4420 MLR ACi 4420 MLR INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 4 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating Data... 5

More information

Product Data Sheet 3214 JH3-195

Product Data Sheet 3214 JH3-195 3214 JH3-195 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 5 3.1 Operating Data - Electrical Interface - Input... 5 3.2 Electrical Operating Data... 6

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEAL 303 FITTINGS 304

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEAL 303 FITTINGS 304 CONTENTS Page - SPECIFICATIONS 200 PERFORMANCE RANGE 201 SELECTION CHART 202 TYPE KEY 203 CURVE SPECIFICATIONS 204 PERFORMANCE CURVE 32-250/5.5 205 PERFORMANCE CURVE 32-250/7.5 205 PERFORMANCE CURVE 32-250/9.2

More information

A Series 50HZ. A - Series. Vertical Multistage Centrifugal in-line Pumps AVC/AVI/AVS ISO-9001

A Series 50HZ. A - Series. Vertical Multistage Centrifugal in-line Pumps AVC/AVI/AVS ISO-9001 A - Series A Series ISO-9 AVC/AVI/AVS HZ Evak Pump Technology Corp. No., Zhongshan Rd., Qingshui Township, Taichung County, Taiwan. Tel : +-- Fax: +--9 www.evak-pumps.com Vol. PIAV- A-Series Index Multistage

More information

Product Data Sheet 4184 N/17X. The engineer's choice

Product Data Sheet 4184 N/17X. The engineer's choice Product Data Sheet 4184 N/17X The engineer's choice 4184 N/17X INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Electrical Operating Data... 4 3.2 Electrical

More information

Lowara. Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733. SH Series. 50 Hz

Lowara. Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733. SH Series. 50 Hz Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733 SH Series 50 Hz SERIE SH OPERATING CHARACTERISTICS AT 50 Hz PRINT 05-2007 2 CONTENTS 5 Specifications......................................................................

More information

Product Data Sheet 4184 NGX

Product Data Sheet 4184 NGX The engineer's choice 4184 NGX INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEAL 303 FITTINGS 304

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEAL 303 FITTINGS 304 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 20 SELECTION CHART TABLE 202 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 32-250/5.5 205 PERFORMANCE CURVE 32-250/7.5 205 PERFORMANCE CURVE

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 ITEM QUANTITY FOR MODEL 302 INTERMEDIATE CASING WITH BEARING POSITION 303

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 ITEM QUANTITY FOR MODEL 302 INTERMEDIATE CASING WITH BEARING POSITION 303 SPECIFICATIONS Page - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART TABLE 202 TYPE KEY 203 PERFORMANCE CHART 2 204 PERFORMANCE CHART 4 205 PERFORMANCE CHART 7 206 PERFORMANCE CHART 15 207 - CONSTRUCTIONS

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 ITEM QUANTITY FOR MODEL 302 INTERMEDIATE CASING WITH BEARING POSITION 303

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 ITEM QUANTITY FOR MODEL 302 INTERMEDIATE CASING WITH BEARING POSITION 303 SPECIFICATIONS Page - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART TABLE 202 TYPE KEY 203 PERFORMANCE CHART 2 204 PERFORMANCE CHART 4 205 PERFORMANCE CHART 7 206 PERFORMANCE CHART 15 207 - CONSTRUCTIONS

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL AND BEARINGS 302 MECHANICAL SEAL 303

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL AND BEARINGS 302 MECHANICAL SEAL 303 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE A (UP TO 0.6 KW) 204 PERFORMANCE CURVE A (FROM 0.75 KW UP TO 1.1 KW) 205 PERFORMANCE CURVE

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL 302 MECHANICAL SEAL 303 BEARINGS 304 FITTINGS 305

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL 302 MECHANICAL SEAL 303 BEARINGS 304 FITTINGS 305 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART TABLE 202 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 3 ( 3-4-5-6 IMPELLERS ) 205 PERFORMANCE CURVE 3 ( 7-8-9 IMPELLERS

More information

OVIM/OVIMF. OVIM 60Hz OVIMF 60Hz. A New Vision for Quality Pumps. Light Vertical Multistage Centrifugal Pumps

OVIM/OVIMF. OVIM 60Hz OVIMF 60Hz. A New Vision for Quality Pumps. Light Vertical Multistage Centrifugal Pumps OVIM/OVIMF A New Vision for Quality Pumps OVIM 60Hz OVIMF 60Hz Light Vertical Multistage Centrifugal Pumps PERFORMANCE SCOPE OVIM/OVIMF PRODUCT RANGE OVIM OVIM2 OVIM3 OVIM4 OVIM8 OVIM6 OVIM32 OVIM42 OVIM65

More information

Lowara. 8 Submersible Electric Pumps. 6Z855, 6Z875 6Z895, 6Z8125 Series. 60 Hz

Lowara. 8 Submersible Electric Pumps. 6Z855, 6Z875 6Z895, 6Z8125 Series. 60 Hz 8 Submersible Electric Pumps 6Z855, 6Z875 6Z895, 6Z8125 Series 60 Hz 6Z855, 6Z875, 6Z895, 6Z8125 SERIES HYDRAULIC PERFORMANCE RANGE AT 60 Hz PRINT 10-2006 2 CONTENTS 6Z8 Series Specifications...5 Table

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEAL 303 FITTINGS 304

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 BEARINGS 302 MECHANICAL SEAL 303 FITTINGS 304 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART TABLE 202 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 32-250/5.5 205 PERFORMANCE CURVE 32-250/7.5 205 PERFORMANCE CURVE

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL AND BEARINGS 302 MECHANICAL SEAL 303

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL AND BEARINGS 302 MECHANICAL SEAL 303 CONTENTS Page - SPECIFICATIONS 200 PERFORMANCE RANGE and SELECTION CHART 201 TYPE KEY 202 CURVE SPECIFICATIONS 203 PERFORMANCE CURVE A (UP TO 0.6 KW) 204 PERFORMANCE CURVE A (FROM 0.75 KW UP TO 1.1 KW)

More information

Page - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING TECHNICAL DATA 500

Page - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING TECHNICAL DATA 500 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE BEST 2 203 PERFORMANCE CURVE BEST 3 203 PERFORMANCE CURVE BEST 4 203 PERFORMANCE CURVE BEST

More information

4WN. EBARA PUMPS EUROPE S.p.A. SUBMERSIBLE MULTISTAGE PUMPS. Pag

4WN. EBARA PUMPS EUROPE S.p.A. SUBMERSIBLE MULTISTAGE PUMPS. Pag CONTENTS Pag - SPECIFICATIONS 200 PUMP SPECIFICATION 200 MOTOR SPECIFICATION 201 SECELTION CHART 202-203 TYPE KEY AND CURVES SPECIFICATIONS 204-205 PERFORMANCE CURVE 1 206 PERFORMANCE CURVE 2 207 PERFORMANCE

More information

SCREW SPINDLE PUMPS COOLING, LUBRICATING, CHIP HANDLING, PRESSURE BOOSTING, FLUSHING, MAINTAINING TEMPERATURES...

SCREW SPINDLE PUMPS COOLING, LUBRICATING, CHIP HANDLING, PRESSURE BOOSTING, FLUSHING, MAINTAINING TEMPERATURES... 2018 SCREW SPINDLE PUMPS COOLING, LUBRICATING, CHIP HANDLING, PRERE BOOSTING, FLUSHING, MAINTAINING TEMPERATURES... www.brinkmannpumps.com Content Technical Information Electrical Features 4 8 Control

More information

IPVP High-pressure Internal Gear Pumps for Variable Speed Drives

IPVP High-pressure Internal Gear Pumps for Variable Speed Drives IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Design and Function 7 6 5 9 2 5 6 7 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing

More information

OVIM/OVIMF. OVIM 60Hz OVIMF 60Hz. A New Vision for Quality Pumps. Light Vertical Multistage Centrifugal Pumps

OVIM/OVIMF. OVIM 60Hz OVIMF 60Hz. A New Vision for Quality Pumps. Light Vertical Multistage Centrifugal Pumps OVIM/OVIMF A New Vision for Quality Pumps OVIM 60Hz OVIMF 60Hz Light Vertical Multistage Centrifugal Pumps OVIM/OVIMF 60Hz General Data PERFORMANCE SCOPE OVIM/OVIMF OVIM1 OVIM2 OVIM3 OVIM4 OVIM8 OVIM16

More information

CVM. EBARA PUMPS EUROPE S.p.A. MULTISTAGE CENTRIFUGAL PUMPS

CVM. EBARA PUMPS EUROPE S.p.A. MULTISTAGE CENTRIFUGAL PUMPS CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE A (UP TO 0.6 kw) 203 PERFORMANCE CURVE A (FROM 0.75 kw UP TO 1.1 kw) 204 PERFORMANCE CURVE

More information

Content. Page 4 7. Technical Information Electrical. Models and Applications Technical Information Potentials for energy savings

Content. Page 4 7. Technical Information Electrical. Models and Applications Technical Information Potentials for energy savings Content Technical Information Electrical Page 4 7 Models and pplications Technical Information Potentials for energy savings 8 0 High Pressure Pumps BFS, FFS / 50 Hz BFS2, FFS2 / 50 Hz High Pressure Pumps

More information

Product Data Sheet 624 NR. The engineer's choice

Product Data Sheet 624 NR. The engineer's choice Product Data Sheet 624 NR Product Data Sheet 624 NR The engineer's choice Product Data Sheet 624 NR 624 NR INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data...

More information

Product Data Sheet 4414/2H

Product Data Sheet 4414/2H The engineer's choice 4414/2H INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating

More information

- continuos running: max ±5%. - intermittent running: max ±10%. Voltage imbalance between phases: max 2%. Maximum number of starts per hour: 30.

- continuos running: max ±5%. - intermittent running: max ±10%. Voltage imbalance between phases: max 2%. Maximum number of starts per hour: 30. Submersible Electric Pumps GLS Series MARKET SECTORS RESIDENTIAL AND COMMERCIAL BUILDINGS, INDUSTRIES. APPLICATIONS Submersible pump for pumping clean water, surface water and wastewater containing solids

More information

CRK 2-180/18 A-W-A-AUUV 3x380 /415Y V

CRK 2-180/18 A-W-A-AUUV 3x380 /415Y V GRUNDFOS DATA BOOKLET CRK 2-18/18 A-W-A-AUUV 3x38 /415Y V Grundfos pump 497218 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/crk2/497218/crk-2-18-18-a-w-a-auuv.html

More information

GRUNDFOS DATA BOOKLET MTR(E), MTH, MTA. Immersible pumps 50/60 Hz

GRUNDFOS DATA BOOKLET MTR(E), MTH, MTA. Immersible pumps 50/60 Hz GRUNDFOS DATA BOOKLET MTR(E), MT, MTA Immersible pumps 5/6 z Contents Product data Introduction 4 Performance range - MTR, 5 z 5 Performance range - MTRE, 5 z 5 Performance range - MTR, 6 z 6 Performance

More information

Product Data Sheet 614 N/2HH-169 The engineer's choice

Product Data Sheet 614 N/2HH-169 The engineer's choice The engineer's choice 614 N/2HH-169 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Electrical Operating Data... 4 3.2 Operating Data - Electrical

More information

Vane pumps, direct controlled Type PV7...A

Vane pumps, direct controlled Type PV7...A Vane pumps, direct controlled Type PV7...A Nominal sizes 1 to 25 eries 1X Maximum operating pressure 1 bar Displacements from 1 to 25 cm 3 H/A 617/95 Type PV7-1X/..RA1MA-... H/A/D 56/97 Typ MPU1-V71-9L/...

More information

TOP MULTI. Submersible multi-stage pumps TOP MULTI 1 TOP MULTI 2-3. PERFORMANCE RANGE Flow rate up to 120 l/min (7.2 m³/h) Head up to 42 m

TOP MULTI. Submersible multi-stage pumps TOP MULTI 1 TOP MULTI 2-3. PERFORMANCE RANGE Flow rate up to 120 l/min (7.2 m³/h) Head up to 42 m TOP MULTI Submersible multi-stage pumps Clean water Domestic use Civil use TOP MULTI 1-3 PERFORMANCE RANGE Flow rate up to 120 l/min (7.2 m³/h) Head up to 42 m APPLICATION LIMITS Immersion depth: up to

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING 401

- CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING 401 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE 70 203 PERFORMANCE CURVE 120 204 PERFORMANCE CURVE 200 205 - CONSTRUCTIONS 300 SECTIONAL VIEW

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL 302 INTERMEDIATE CASING WITH BEARING POSITION 303

- CONSTRUCTIONS 300 SECTIONAL VIEW DRAWING 300 SECTIONAL VIEW TABLE 301 QUANTITY FOR MODEL 302 INTERMEDIATE CASING WITH BEARING POSITION 303 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART TABLE 202 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 2 205 PERFORMANCE CURVE 4 206 PERFORMANCE CURVE 7 207 PERFORMANCE

More information

Product Data Sheet 8412 N/ The engineer's choice

Product Data Sheet 8412 N/ The engineer's choice The engineer's choice 8412 N/12-252 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Electrical Operating Data... 4 3.2 Electrical Interface - Output...

More information

Side Channel Pumps Self-priming, segmental type with verly low NPSH

Side Channel Pumps Self-priming, segmental type with verly low NPSH Side Channel Pumps Self-priming, segmental type with verly low NPSH CEH Sizes 1201 6108, 1202/5 6108/5, 1202/7 6107/7 Technical data Capacity: Delivery head: Speed: max. 35 m³/h max. 354 m max. 1800 1/min

More information

2CDX. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page

2CDX. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE 70 203 PERFORMANCE CURVE 120 204 PERFORMANCE CURVE 200 205 - CONSTRUCTIONS 300 SECTIONAL VIEW

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW (4N1 4N2 4N4) 300 SECTIONAL VIEW (4N7 4N10 4N15) 301 SECTIONAL VIEW TABLE 302 ITEM QUANTITY FOR MODEL 303

- CONSTRUCTIONS 300 SECTIONAL VIEW (4N1 4N2 4N4) 300 SECTIONAL VIEW (4N7 4N10 4N15) 301 SECTIONAL VIEW TABLE 302 ITEM QUANTITY FOR MODEL 303 CONTENTS Page - CONTENTS 100 - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART 202 TYPE KEY 203 PERFORMANCE CHART 4N1 204 PERFORMANCE CHART 4N2 205 PERFORMANCE CHART 4N4 206 PERFORMANCE CHART 4N7

More information

Data sheet. Etaline GN /1852 G10 Version no.: 1 Inline pump. Operating data. Design. Requested developed head m

Data sheet. Etaline GN /1852 G10 Version no.: 1 Inline pump. Operating data. Design. Requested developed head m Data sheet Item no.: 2600 Page: 1 / 5 Operating data Requested flow rate 40.00 m ³/h Actual flow rate 40.00 m ³/h Requested developed head 68.00 m Actual developed head 68.00 m Pumped medium Water Efficiency

More information

Product Data Sheet 8414 NGH

Product Data Sheet 8414 NGH The engineer's choice 8414 NGH INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical Operating

More information

A Series 50HZ. A - Series. Vertical Multistage Centrifugal in-line Pumps AVC/AVI/AVS ISO-9001

A Series 50HZ. A - Series. Vertical Multistage Centrifugal in-line Pumps AVC/AVI/AVS ISO-9001 A - Series A Series ISO-9 AVC/AVI/AVS HZ Evak Pump Technology Corp. No., Zhongshan Rd., Qingshui Township, Taichung County, Taiwan. Tel : +-- Fax: +--9 www.evak-pumps.com Vol. PIAV- A-Series Index Pump

More information

Data sheet. Page: 1 / 5. ETL GGSAV11D BKSBIE3 Inline pump. Operating data. Design

Data sheet. Page: 1 / 5. ETL GGSAV11D BKSBIE3 Inline pump. Operating data. Design Data sheet Page: 1 / 5 Operating data Requested flow rate Operating data determined for maximum inlet pressure Requested developed head 15.00 m Pumped medium Ambient air temperature 20.0 C Fluid temperature

More information

3D SERIES. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page

3D SERIES. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page CONTENTS Page - SPECIFICATIONS 0 SELECTION CHART 1 TYPE KEY 3 PERFORMANCE CURVE SPECIFICATIONS 4 PERFORMANCE CURVE 32-125 5 PERFORMANCE CURVE 32-6 PERFORMANCE CURVE 32-0 7 PERFORMANCE CURVE 40-125 8 PERFORMANCE

More information

Side channel pumps PN 16 SOH - SOHB - SOHM. Self-priming centrifugal pumps. Technical description

Side channel pumps PN 16 SOH - SOHB - SOHM. Self-priming centrifugal pumps. Technical description Side channel pumps PN 16 Self-priming centrifugal pumps SOH - SOHB - SOHM Technical description ATEX certified The SOH side channel pump models are available in a variety of designs. Design base plate

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEALS 301 BEARINGS DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING TECHNICAL DATA 500

- CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEALS 301 BEARINGS DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING TECHNICAL DATA 500 CONTENTS Page - SPECIFICATIONS 200 PERFORMANCE RANGE and SELECTION CHART 201 TYPE KEY 202 CURVE SPECIFICATIONS 202 PERFORMANCE CURVE BEST 2 203 PERFORMANCE CURVE BEST 3 204 PERFORMANCE CURVE BEST 4 205

More information

e-sv Series 1, 3, 5, 10, 15, 22, 33, 46, 66, 92, 125

e-sv Series 1, 3, 5, 10, 15, 22, 33, 46, 66, 92, 125 e-sv Series 1, 3, 5, 10, 15, 22, 33, 46, 66, 92, 125 Vertical Multistage Electric Pumps equipped with high efficiency motors 50 Hz e-sv SERIES HYDRAULIC PERFORMANCE RANGE AT 50 Hz WEB 07-2010 2 CONTENTS

More information

SS7 SUBMERSIBLE ELECTRIC PUMPS 7

SS7 SUBMERSIBLE ELECTRIC PUMPS 7 SS7 TECHNICAL DATA Performance range: flow up to 110 m3/h and max head of 423 m Max. quantity of sand/silt: 50g/m3 Max. ambient temperature: 30 C (50 C available on request) Outlet connection diameter

More information

Feed Pumps VP / VPB / VPBM

Feed Pumps VP / VPB / VPBM Feed Pumps VP / VPB / VPBM Symbol General The feed pumps from the VP series are low-noise, single-stroke vane pumps with constant flow rate. Using a damped bell housing (PT) enables noise levels to be

More information

Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 202 CURVE SPECIFICATIONS 203 PERFORMANCE CHART COMPACT A 204 PERFORMANCE CHART COMPACT B 205

Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 202 CURVE SPECIFICATIONS 203 PERFORMANCE CHART COMPACT A 204 PERFORMANCE CHART COMPACT B 205 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 202 CURVE SPECIFICATIONS 203 PERFORMANCE CHART A 204 PERFORMANCE CHART B 205 - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEALS 301

More information

Feed Pumps Direct Drive Series 1.1.

Feed Pumps Direct Drive Series 1.1. 1.1. FEED PUMP SERIES FZP AND MFZP 1. GENERAL The feed pump, type FZP, is a direct drive vane pump with constant flow rate. It is available with flanged motor (MFZP) and comes with internal pressure relief

More information

SVI SERIES HYDRAULIC PERFORMANCE RANGE AT 50 Hz

SVI SERIES HYDRAULIC PERFORMANCE RANGE AT 50 Hz 50 Hz SVI Series 2, 4, 8, 16, 33, 46, 66, 92 SUBMERSIBLE VERTICAL ELECTRIC PUMPS EQUIPPED WITH IE2 MOTORS COMPLYING WITH REGULATION (EC) no. 640/2009 Cod. 191002451 Rev ev.a.a Ed.01/2012 SVI SERIES HYDRAULIC

More information

Feed Pumps Direct Drive Series 1.1.

Feed Pumps Direct Drive Series 1.1. 1.1. FEED PUMP SERIES FZP AND MFZP 1. GENERAL The feed pump, type FZP, is a direct drive vane pump with constant flow rate. It is available with flanged motor (MFZP) and comes with internal pressure relief

More information

CRE20-08 A-F-A-E-HQQE 3x HZ

CRE20-08 A-F-A-E-HQQE 3x HZ GRUNDFOS DATA BOOKLET CRE2-8 A-F-A-E-HQQE 3x4 6 HZ Grundfos pump 96514642 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/cre2/96514642/cre-2-8-a-f-a-e-hqqe.html

More information

Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733. SH Series

Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733. SH Series Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733 MARKET SECTORS The Lowara SH series pumps are used for water and clean liquid circulation in heating, ventilating and

More information

product specification

product specification 4414 ML Customer specification: No Version: 1.0 Created: 16.09.2011 INDEX 1 General... 2 2 Mechanics... 2 2.1 GENERAL... 2 2.2 MOTOR... 2 2.3 CONNECTIONS... 3 3 Operating Data... 4 3.1 OPERATING DATA -

More information

A Series. 60 Hz. A - Series. Vertical Multistage Centrifugal in-line Pumps AVC/AVI/AVS ISO-9001

A Series. 60 Hz. A - Series. Vertical Multistage Centrifugal in-line Pumps AVC/AVI/AVS ISO-9001 A - Series A Series ISO-9 AVC/AVI/AVS Hz Evak Pump Technology Corp. No. 55, Zhongshan Rd., Qingshui Dist., Taichung City, Taiwan. Tel : +--55 Fax: +--5559 www.evak-pumps.com Vol. PIAV- A-Series Index Pump

More information

IPVS High-pressure Internal Gear Pumps Technical Data Sheet

IPVS High-pressure Internal Gear Pumps Technical Data Sheet IPVS High-pressure Internal Gear Pumps Technical Data Sheet Functional Drawing 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing segment 5 Axial

More information

Screw Pumps Series EMTEC HIGH-TECH FOR EMULSION. 20 DQ axial branch with pipe thread. 140 D8.6 radial branch with SAE flange

Screw Pumps Series EMTEC HIGH-TECH FOR EMULSION. 20 DQ axial branch with pipe thread. 140 D8.6 radial branch with SAE flange Screw Pumps 20 DQ axial branch with pipe thread HIGH-TECH FOR EMULSION 140 D8.6 radial branch with SAE flange Application For handling good, medium or mal-lubricating, abrasive fluids in cooling lubricant

More information

CRK 2-180/18 A-W-A-AUUV 3x230/400V 60HZ

CRK 2-180/18 A-W-A-AUUV 3x230/400V 60HZ GRUNDFOS DATA BOOKLET CRK 2-18/18 A-W-A-AUUV 3x23/4V 6HZ Grundfos pump 497178 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/crk2/497178/crk-2-18-18-a-w-a-auuv.html

More information

Product Data Sheet 632 NU-006

Product Data Sheet 632 NU-006 The engineer's choice 632 NU-006 INDEX 1 General... 3 2 Mechanics... 3 2.1 General... 3 2.2 Connections... 3 3 Operating Data... 4 3.1 Operating Data - Electrical Interface - Input... 4 3.2 Electrical

More information

IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Technical Data Sheet

IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Technical Data Sheet IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Technical Data Sheet Design and Function 7 6 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b

More information

60 Hz. SVI Series 2, 4, 8, 16, 33, 46, 66, 92 SUBMERSIBLE VERTICAL ELECTRIC PUMPS EQUIPPED WITH IE3 MOTORS

60 Hz. SVI Series 2, 4, 8, 16, 33, 46, 66, 92 SUBMERSIBLE VERTICAL ELECTRIC PUMPS EQUIPPED WITH IE3 MOTORS 6 Hz SVI Series 2, 4, 8, 16, 33, 46, 66, 92 SUBMERSIBLE VERTICAL ELECTRIC PUMPS EQUIPPED WITH IE3 MOTORS Cod. 1911291 Rev. C Ed.1/217 SVI SERIES HYDRAULIC PERFORMANCE RANGE AT 6 Hz 2 CONTENTS Specifications

More information

E 068 E 088 In-line mounting Connection up to G¾ Nominal flow rate up to 100 l/min

E 068 E 088 In-line mounting Connection up to G¾ Nominal flow rate up to 100 l/min Return-Suction Filters E 68 E 88 In-line mounting Connection up to G¾ Nominal flow rate up to l/min Description Application For operation in units with hydrostatic drives, when the return flow is under

More information