ACQUITY UPLC I-Class System with 2D Technology

Transcription

1 ACQUITY UPLC I-Class System with 2D Technology The Waters ACQUITY UPLC I-Class System with 2D Technology allows chemists to increase sensitivity and selectivity, eliminate unwanted interferences, characterize the most complex samples, and perform separations that are normally incompatible with a mass spectrometer by adding a second reversed-phase separation to the experiment. The system is comprised of the following: Sample Manager with Flow-Through Needle (SM-FTN) or a Sample manager Fixed Loop (SM-FL), Column Manager (CM-A), Binary Solvent Manager (Analytical Pump) and either a second Binary Solvent Manager or Quaternary Solvent Manager as the injection pump. ACQUITY UPLC I-CLASS BINARY SOLVENT MANAGERS Number of solvents Solvent conditioning Gradient formation Up to four, in any combination of two: A1 or A2 and B1 or B2 Integrated vacuum degassing, six lines with two allocated for the injector needle wash/purge solvents High pressure mixing, binary gradient Gradient profiles 11 gradient curves [including linear, step (2), concave (4), and convex (4)] Operating flow rate range Maximum operating pressure Primary check valves Flow accuracy Flow precision Composition ripple (baseline noise) Pump compositional precision Pump compositional accuracy Compressibility compensation to ml/min, in ml increments 18,000 psi up to 1 ml/min, 12,000 psi up to 2 ml/min Intelligent Intake Valves (i 2 Valve) ±1.0% of set flow rate at ml/min, as per SystemsQT 0.075% RSD or 0.01 min SD, (0.2 to 2.0 ml/min), whichever is greater using pre-mixed solvent <1.0 mau <0.2% RSD, or 0.02 min SD, whichever is greater (from 0.2 to 2.0 ml/min) ±0.5% absolute from 5% to 95%, 0.2 to 2.0 ml/min Automatic, no user intervention required ph range ph 2 to 12 Priming Pump seal wash Flow ramping Mixing options Wet priming runs at a flow rate of 4 ml/min Equipped with a programmable active wash system to flush the rear of the high pressure seals and the plungers Automatic 316L stainless steel, UHMWPE blend, MP35N, titanium alloy, gold, sapphire, ruby, zirconia, Nitronic 60, DLC, fluoropolymer, PEEK and PEEK blend Standard: 50 μl Optional: 100 μl and 380 μl

2 QUATERNARY SOLVENT MANAGER (QSM) Number of solvents Maximum operating pressure Solvent conditioning Gradient formation One to four, in any combination as standard. Expanded solvent choices with optional six-port solvent select valve 15,000 psi up to 1 ml/min, 9000 psi up to 2 ml/min Integrated vacuum degassing, four chambers. One additional for the SM-FTN purge solvent Low-pressure mixing, quaternary gradient Gradient profiles 11 gradient curves [including linear, step (2), concave (4), and convex (4)] Primary check valve Flow accuracy Intelligent Intake Valve (i 2 Valve) ±1.0% at 0.5 to 2.0 ml/min using 100% A Back pressure 600 to 1000 psi with degassed H 2 0 Flow precision Composition ripple (baseline noise) Composition accuracy Composition precision Compressibility compensation 0.075% RSD or ±0.020 min SD, whichever is greater, based on six replicates. 60:40 H 2 O/MeOH via Auto Blend Plus Technology, 0.5 ml/min, alkylphenone mix (5.0 μl injection volume), ACQUITY UPLC BEH C x 50 mm, 1.7 μm 35 C ± 0.3 C, 254 nm <1.0 mau (<0.1 mau with optional μl mixer) A: H 2 O + 0.1% TFA, B: ACN + 0.1% TFA, 0.5 ml/min, ACQUITY UPLC BEH C x 50 mm, 1.7 μm, 214 nm, 10-mm analytical flow cell ±0.5% absolute (full scale) from 5% to 90% from 0.5 to 2.0 ml/min. 90:10 Degassed ACN/H 2 O, 90:10 ACN/H 2 O with caffeine at 12 mg/l concentration, back pressure 2000 psi, step gradient method, UV at 273 nm alkylphenone mix (5.0 μl injection volume), ACQUITY BEH C x 50 mm, 1.7 μm 35 C ± 0.3 C, UV at 254 nm <0.15% RSD or ±0.04 min SD, whichever is greater, based on six replicate injections. 60:40 H 2 O/MeOH via Auto Blend Plus Technology, 0.5 ml/min, alkylphenone mix (5.0 μl injection volume), ACQUITY UPLC BEH C x 50 mm, 1.7 μm, 35 C ± 0.3 C, 254 nm Automatic and continuous ph range ph 2 to 12 Priming Pump seal wash Flow ramping Wet priming can run at flow rates up to 4 ml/min Equipped with a wash system to flush the rear of the high pressure seal and the plunger Range: 0.01 to min to reach 2.0 ml/min Default: 0.45 min to reach 2.0 ml/min 316L stainless steel, PPS, fluoropolymer, fluoroelastomer, UHMWPE blend, sapphire, ruby, zirconia, Nitronic 60, DLC, PEEK and PEEK blend, titanium alloy 2

3 SAMPLE MANAGER (SM-FTN) Injection volume range Accuracy 0.1 to 10.0 μl as standard configuration. Up to μl with optional extension loop ±0.2 μl, measured by fluid weight removed from vial with 10.0 μl injections averaged over 20 injections using standard µL syringe Injection linearity >0.999 Sample manager precision Maximum sample capacity <1% area RSD 0.2 to 1.9 μl injection <0.5% area RSD 2.0 to 10.0 μl injection Any two of the following: n 96 and 384 microtiter plates n 48 position 2.00-mL vial plates n 48 position 0.65-mL micro-centrifuge tube plates n 24 position 1.50-mL micro-centrifuge tube plates Sample compartment temperature range 4.0 to 40.0 C, settable in 0.1 C increments with a tolerance range between -2.0 and +4.0 C Temperature accuracy ±0.5 C Temperature stability ±1.0 C Injection needle wash Minimum sample required Advanced sample manager capabilities Integrated, active, programmable 3 μl residual, using Waters total recovery 2-mL vials (zero offset) Auto-dilution and auto-addition 316L stainless steel, polyimide, PEEK blend, DLC, PPS SAMPLE MANAGER FIXED LOOP (SM-FL) Injection volume range Injection linearity Injection mode Sample manager precision 0.1 μl to μl, in 0.1-μL increments. 10 μl loop standard with 1, 2, 5, 20, 50, 100, and 250 μl optional loops >0.999, (default needle) from 20% to 75% of loop, Partial Loop Uses Needle Overfill mode, (PLUNO), per SystemsQT protocol Three Full Loop mode, for optimal quantitation and dispersion, Partial Loop mode for fastest cycle time, and Partial Loop Uses Needle Overfill mode, default mode, for optimal quantitation using partial loop injection volumes <1% area RSD 0.2 to 1.9 μl injection <0.5% area RSD 2 to 10 μl injection (See ACQUITY UPLC I-Class System Specifications document for conditions) 3

4 Number of sample plates Maximum sample capacity Sample compartment temperature range Temperature accuracy Temperature stability Injection needle wash Minimum sample required Any two of the following: 96 and 384 microtiter plates 48 position 2.00-mL vial plates 48 position 0.65-mL micro-centrifuge tube plates 24 position 1.50-mL micro-centrifuge tube plates 768 in two 384-well plates, or 96 in 2-mL vial holders, plus 4 additional positions for dilution functions 4.0 to 40.0 C, settable in 0.1 C increments; maintains 19 C below ambient with a tolerance range between -2 and +4 C ±0.5 C at sensor (See ACQUITY UPLC I-Class Systems Specification Guide for conditions) ±1.0 C at sensor (See ACQUITY UPLC I-Class Systems Specification Guide for conditions) Integrated, active, programmable, dual wash 3 μl residual, using Waters total recovery 2-mL vials (zero offset) Carryover (UV) <0.004% <0.002% typical (See ACQUITY UPLC I-Class System Specifications document for conditions) Advanced sample manager capabilities Load Ahead and Loop Offline mode, valve cycle timed event 316L stainless steel, UHMWPE blend, MP35N, DLC, titanium alloy, gold, sapphire, ruby, zirconia, Nitronic 60, fluoropolymer, PEEK and PEEK blend, fluoroelastomer COLUMN MANAGEMENT (CM-A) Column capacity Multidimensional valves Column compartment(s) Temperature range CM-A: Two columns, as standard (maximum length of 150 mm with filter or guard column) or four columns (maximum length of 50 mm) can be supported with optional tubing kit, up to 4.6 mm internal diameter (I.D.). Two six-port, two-position valves (CM-A only) 4.0 to 90.0 C, settable in 0.1 C increments Two independent heat/cool zones per module Column compartment(s) ±0.5 C temperature accuracy Column compartment(s) ±0.3 C temperature stability Solvent conditioning Column tracking Active pre-heating as standard ecord Technology column information management tracks and archives column usage history for one column 4

5 SAMPLE ORGANIZER Sample plate capacity Maximum sample capacity Sample plate capacity is configured based on the types and combinations of plates being used: n Maximum of 19 standard microtiter plates, up to 15.5 mm high, or n Maximum of 9 intermediate height plates (or 2-mL vial holders), up to 40.0 mm high, or n Maximum of 6 deep well plates (or 4-mL vial holders), up to 47.0 mm high Maximum of 7296 samples in nineteen 384-well plates Sample compartment temperature range 4.0 to 40.0 C, settable in 0.1 C increments with a tolerance range between -2.0 to +4.0 Temperature accuracy Temperature stability ±1 C at the sensor ±1 C at the sensor INSTRUMENTAL CONTROL External communication Event inputs/outputs External control User diagnostics Unattended operation Connections INSIGHT Ethernet interfacing via RJ45 connection to host PC with BSM, or Column Manager and ACQUITY UPLC Detectors and mass spectrometers Rear panel contact closure and/or TTL inputs/outputs MassLynx version 4.1 with OpenLynx Open Access, with specific SCN releases Available through software on host PC; system control via console software Leak sensors on supported modules, full diagnostic data captured through console software Provides real-time monitoring, automatic notification of instrument performance, and diagnostic information allowing for quicker problem resolution ENVIRONMENTAL Acoustic noise Operating temperature range Operating humidity range <65 db 4.0 to 40.0 C (39.2 to F) 20% to 50%, non-condensing POWER REQUIREMENTS Voltage range Frequency 100 to 240 VAC 50 to 60 Hz 5

6 PHYSICAL DIMENSIONS ACQUITY UPLC I-Class System with Width: 83.8 cm (33 in.) 2D Technology comprised of: Height: cm (40.7 in.) ACQUITY UPLC Sample Manager - FTN, Depth: 86.4 cm (34 in.) two Solvent Managers, and Column Manager Note: dimensions are listed with only components listed above ORDERING INFORMATION PART NUMBER ACQUITY UPLC I-Class System with 2D Technology (SM-FTN), 2x BSM ACQUITY UPLC I-Class System with D Technology (SM-FTN), QSM/BSM ACQUITY UPLC I-Class System with D Technology (SM-FL), 2x BSM Waters, ACQUITY UPLC, UPLC, Connections INSIGHT, MassLynx, and The Science of What s Possible are registered trademarks of Waters Corporation. OpenLynx, SystemsQT, Auto Blend Plus and ecord are trademarks of Waters Corporation. All other trademarks are the property of their respective owners Waters Corporation. Produced in the U.S.A. October EN TC-PDF Waters Corporation 34 Maple Street Milford, MA U.S.A. T: F: