Bulletin C Dean Pump Division. Chemical Process Industrial Inline Pumps. DeanLine Series

Transcription

1 Bulletin C Dean Pump Division Chemical Process Industrial Inline Pumps DeanLine Series

2 DeanLine Series Chemical Process Industrial Inline Pumps Capacities to 95 GPM (22m /hr) Heads to 1 Feet (9 m) Pumping Temperatures to 22 F (14 C) Working Pressures to 1 PSIG (689 kpa) Two Sizes DeanLine Series Pumps offer inline pump convenience for simple installations. They are excellent for process plant pump applications for capacities and heads less than ANSI AA and AB sizes. Standard features include an open impeller with integral seal and an electric driven motor. An optional air driven motor is also available. Two pump sizes are available in cast iron and 16SS construction. Special features include: Factory testing for operating performance and hydrostatic testing for casting soundness Standard shaft extension to eliminate alignment problems, no coupling needed Applications Transfer Service Bottle Wash Systems Hospital Service Loading Pumps - Lime Water Circulation Tank Car Unloading - Water Circulation Kidney Dialysis System Cleaning Solutions Condensate Service Pilot Plant Applications Line Boosters Starch Slurries Soft Slurries Dye Liquors Paper Coating Distilleries Plating Solutions Aquarium Water Circulation Heat Transfer Liquids Solvent Recovery Systems Liquids Handled Include: 15% Acetic Acid & Water Alcohol Alcohol & Water Binder Solution Boron Triflouride Brandy Brine 14 Butate Diol Condensate Cordials Cyanide Rinse Deonized Water Dimethylamine 2ºF Dowtherm* *Dow Chemical Co. EDC Reflux Epichlorohydrin Fatty Alcohol Freon II Formaldehyde JP4 Fuel Gasoline Glycol Heat Transfer Oil Hexachlorophene Hexane Hot Water Hot Wax Hydro Carbons and Dissolved H 2 S Hydrogen Sulfide Kerosene Light Oil Lime Water Methanol Mineral Oil 7% NA Carbonate Solution Pentachlorophenol Perchloro-ethylene 25ºF Polystyrene Quench Oil Slurries Sodium Hydroxide Sodium Nitrate Soluble Paint and Water Solvents Sour Water Sulfuric, Concentrated Tetrachlorethane Thinners Trichlorobenzene Turpentine Vegetable Oil Vinegar Xylene Zinc Hydro Sulfate 2

3 1 1 / 2 DL Performance Electric Motor TOTAL HEAD FEET DIA 5 RPM.98 DIA 5 RPM.56 DIA 5 RPM 4.75 DIA 175 RPM CAPACITY CUBIC METERS PER HOUR % EFF FT NPSH BHP 1/ 2 BHP 4 FT NPSH SP GR. 11/ 2 BHP TOTAL HEAD METERS / 4 DL Performance Electric Motor CAPACITY CUBIC METERS PER HOUR % EFF 5.75 DIA 5 RPM FT NPSH TOTAL HEAD FEET DIA 5 RPM 4.25 DIA 5 RPM 2 1 SP GR. 1 / BHP BHP 2 TOTAL HEAD METERS DIA 175 RPM 1/ 2 BHP FT NPSH 2 4

4 Air Motor 1 1 / 2 DL Performance Air Motor NPSH FEET TOTAL HEAD FEET 2 1 / 4 DL Performance Air Motor SCFM RPM SCFM NPSH 6 SCFM FREE AIR 4 SCFM Q-H 2 SCFM MAXIMUM RPM 11/ X 11 2 / 2 DEANLINE 6AM AIR MOTOR 4 / DIA. IMPELLER PSI 15 PSI 4 PSI PSI REQUIRED AIR PRESSURE NPSH FEET TOTAL HEAD FEET RPM MAXIMUM 25 2 NPSH Q-H 4 SCFM 2 PSI SCFM 1 PSI 4 PSI 5 PSI / 4 / 4 X DEANLINE 6AM AIR MOTOR 5 / DIA. IMPELLER 8 5 SCFM PSI REQUIRED AIR PRESSURE Options 1 2 Motor: For hazardous duty, an air motor can deliver up to 1 gpm at 96 ft. of head with 5 psi air pressure. A turn of the pressure regulator adjusts the pump speed to match needs. The motor can deliver 4 hp at rpm with 1 psi air pressure at the inlet. 4 4

5 Direction of Rotation (Viewed from Motor End) Driver Rating Horsepower RPM Flanges A.N.S.I. Rating Impeller Maximum Working Pressure Maximum Suction Pressure Hydrostatic Test Pressure Pumping Temperature Minimum Maximum Stuffing Box Corrosion Allowance MECHANICAL DESIGN SPECIFICATIONS Clockwise 2/46 Volt. Phase, 6 Cycle, NEMA C Flange. 14TCZ Frame, Dean Standard Motors, 4SS Shaft with standard shaft extension for jet motor, NEMA TB temperature rating for Ex. Pr. motors, which are Class 1, Troup D; Class II, Groups F&G. 1/2 HP 1, 1 1 /2 and 2 HP Class 125 C.I., Class 15 16SS Single Plane Spin Balance 1 PSIG Any Part of Working Pressure 15 PSIG C.I. and 2 PSIG 16SS Minus 2ºF C.I. and 16SS 22ºF C.I. and 16SS Integral Mechanical Seal Only, Internal Seal Face Flushing All Pumps 1/8 inch MECHANICAL SEAL SPECIFICATIONS Pump Mechanical Suction Pressure Temperature Material Class Seal Max Min. Max Min. 2 or5 Dean Type 6A, 1 PSIG 2 PSIA 22ºF -2ºF 6C or 9A 5 STANDARD MATERIALS OF CONSTRUCTION Part Part No. Iron (Class 2) 16SS (Class 5) Impeller C.I. 16SS Casing 5 C.I. 16SS Casing Cap Screw 5D ASTM A7 Steel Adapter Cradle 7 C.I. Adapter Cap Screw 7G ASTM A7 Steel Casing Back Cover 22 C.I. 16SS Clearance Shim 7 Plastic Casing Gasket 77 Aramid Fiber Stationary Seal Element Stationary Face Spring Holder Shaft Packing 95A Carbon 4SS Viton Carbon 16SS 16SS Teflon Rotating Seal Face 95B Ceramic Seal Dowel Pin 75 Not Required 16SS Options External Flush: When specified, the seal chamber can be supplied with an external flush instead of the standard internal flush. Seal Chamber: In addition to our standard seals, the 6C seal is available for caustic service. It is composed of 4SS metal parts, high aluminum ceramic vs. carbon mating faces, and a viton bellows.

6 Dimensions /4 DL 1 1/2 DL A B C D E.875 O.D., FOUR.56 HOLES ON 2.75 DIA. B.C. 5. O.D., FOUR.625 HOLES ON.875 DIA. B.C. DIMENSION # CP HP TEFC EXPR / C / All dimensions are in inches. Dean Pump Division 64 Guion Road Indianapolis, IN Phone: (17) TOLL FREE: (8) FAX: (17) info@deanpump.com Web Site: COPYRIGHT 25 MET-PRO CORPORATION, DEAN PUMP DIVISION Dean Pump IS A REGISTERED TRADEMARK OF MET-PRO CORPORATION