Chapter 9 GAS POWER CYCLES

Size: px

Start display at page:

Download "Chapter 9 GAS POWER CYCLES"

Shavonne Nichols
6 years ago
Views:

1 Thermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 9 GAS POWER CYCLES Mehmet Kanoglu University of Gaziantep Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction or display.

2 Objectives Evaluate the performance of gas power cycles for which the working fluid remains a gas throughout the entire cycle. Develop simplifying assumptions applicable to gas power cycles. Review the operation of reciprocating engines. Analyze both closed and open gas power cycles. Solve problems based on the Otto, Diesel, Stirling, and Ericsson cycles. Solve problems based on the Brayton cycle; the Brayton cycle with regeneration; and the Brayton cycle with intercooling, reheating, and regeneration. Analyze jet-propulsion cycles. Identify simplifying assumptions for second-law analysis of gas power cycles. Perform second-law analysis of gas power cycles. 2

3 BASIC CONSIDERATIONS IN THE ANALYSIS OF POWER CYCLES Most power-producing devices operate on cycles. Ideal cycle: A cycle that resembles the actual cycle closely but is made up totally of internally reversible processes. Reversible cycles such as Carnot cycle have the highest thermal efficiency of all heat engines operating between the same temperature levels. Unlike ideal cycles, they are totally reversible, and unsuitable as a realistic model. Thermal efficiency of heat engines: Modeling is a powerful engineering tool that provides great insight and simplicity at the expense of some loss in accuracy. The analysis of many complex processes can be reduced to a manageable level by utilizing some idealizations. 3

The ideal cycles are internally reversible, but, unlike the Carnot

Therefore, the thermal efficiency of an ideal cycle, in general, is

4 The ideal cycles are internally reversible, but, unlike the Carnot cycle, they are not necessarily externally reversible. Therefore, the thermal efficiency of an ideal cycle, in general, is less than that of a totally reversible cycle operating between the same temperature limits. However, it is still considerably higher than the thermal efficiency of an actual cycle because of the idealizations utilized. 4

On a T-s diagram, the ratio of the area enclosed by the cyclic curve to the area under the heat-addition process curve represents the thermal efficiency of the cycle.

5 On a T-s diagram, the ratio of the area enclosed by the cyclic curve to the area under the heat-addition process curve represents the thermal efficiency of the cycle. Any modification that increases the ratio of these two areas will also increase the thermal efficiency of the cycle. The idealizations and simplifications in the analysis of power cycles: 1. The cycle does not involve any friction. Therefore, the working fluid does not experience any pressure drop as it flows in pipes or devices such as heat exchangers. 2. All expansion and compression processes take place in a quasi-equilibrium manner. 3. The pipes connecting the various components of a system are well insulated, and heat transfer through them is negligible. Care should be exercised in the interpretation of the results from ideal cycles. On both P-v and T-s diagrams, the area enclosed by the process curve represents the net work of the cycle. 5

THE CARNOT CYCLE AND ITS VALUE IN ENGINEERING The Carnot cycle is composed of four totally reversible processes: isothermal heat addition, isentropic expansion, isothermal heat rejection, and

6 THE CARNOT CYCLE AND ITS VALUE IN ENGINEERING The Carnot cycle is composed of four totally reversible processes: isothermal heat addition, isentropic expansion, isothermal heat rejection, and isentropic compression. For both ideal and actual cycles: Thermal efficiency increases with an increase in the average temperature at which heat is supplied to the system or with a decrease in the average temperature at which heat is rejected from the system. A steady-flow Carnot engine. P-v and T-s diagrams of a Carnot cycle. 6

The combustion process is replaced by a heat-addition process from an external source. 4.

7 AIR-STANDARD ASSUMPTIONS The combustion process is replaced by a heat-addition process in ideal cycles. Air-standard assumptions: 1. The working fluid is air, which continuously circulates in a closed loop and always behaves as an ideal gas. 2. All the processes that make up the cycle are internally reversible. 3. The combustion process is replaced by a heat-addition process from an external source. 4. The exhaust process is replaced by a heat-rejection process that restores the working fluid to its initial state. Cold-air-standard assumptions: When the working fluid is considered to be air with constant specific heats at room temperature (25 C). Air-standard cycle: A cycle for which the air-standard assumptions are applicable. 7

8 AN OVERVIEW OF RECIPROCATING ENGINES Compression ratio Mean effective pressure Spark-ignition (SI) engines Compression-ignition (CI) engines Nomenclature for reciprocating engines. 8

9 OTTO CYCLE: THE IDEAL CYCLE FOR SPARK-IGNITION ENGINES Actual and ideal cycles in spark-ignition engines and their P-v diagrams. 9

Four-stroke cycle 1 cycle = 4 stroke = 2 revolution Two-stroke cycle 1 cycle = 2 stroke = 1 revolution The two-stroke engines are generally less efficient than their four-stroke counterparts but

10 Four-stroke cycle 1 cycle = 4 stroke = 2 revolution Two-stroke cycle 1 cycle = 2 stroke = 1 revolution The two-stroke engines are generally less efficient than their four-stroke counterparts but they are relatively simple and inexpensive, and they have high power-to-weight and power-to-volume ratios. T-s diagram of the ideal Otto cycle. Schematic of a two-stroke reciprocating engine. 10

11 11

12 Thermal efficiency of the ideal Otto cycle as a function of compression ratio (k = 1.4). In SI engines, the compression ratio is limited by autoignition or engine knock. The thermal efficiency of the Otto cycle increases with the specific heat ratio k of the working fluid. 12

DIESEL CYCLE: THE IDEAL CYCLE FOR COMPRESSION-IGNITION ENGINES In diesel engines, only air is compressed during the compression stroke, eliminating the possibility of autoignition (engine knock).

13 DIESEL CYCLE: THE IDEAL CYCLE FOR COMPRESSION-IGNITION ENGINES In diesel engines, only air is compressed during the compression stroke, eliminating the possibility of autoignition (engine knock). Therefore, diesel engines can be designed to operate at much higher compression ratios than SI engines, typically between 12 and isentropic compression 2-3 constantvolume heat addition 3-4 isentropic expansion 4-1 constantvolume heat rejection. In diesel engines, the spark plug is replaced by a fuel injector, and only air is compressed during the compression process. 13

14 Cutoff ratio for the same compression ratio Thermal efficiency of the ideal Diesel cycle as a function of compression and cutoff ratios (k=1.4). 14

15 Dual cycle: A more realistic ideal cycle model for modern, high-speed compression ignition engine. P-v diagram of an ideal dual cycle. QUESTIONS??? Diesel engines operate at higher air-fuel ratios than gasoline engines. Why? Despite higher power to weight ratios, two-stroke engines are not used in automobiles. Why? The stationary diesel engines are among the most efficient power producing devices (about 50%). Why? What is a turbocharger? Why are they mostly used in diesel engines compared to gasoline engines. 15

constant regeneration (internal heat transfer from the regenerator back to the working fluid) A regenerator is a device that borrows energy from the

16 STIRLING AND ERICSSON CYCLES Stirling cycle 1-2 T = constant expansion (heat addition from the external source) 2-3 v = constant regeneration (internal heat transfer from the working fluid to the regenerator) 3-4 T = constant compression (heat rejection to the external sink) 4-1 v = constant regeneration (internal heat transfer from the regenerator back to the working fluid) A regenerator is a device that borrows energy from the working fluid during one part of the cycle and pays it back (without interest) during another part. T-s and P- vdiagrams of Carnot, Stirling, and Ericsson cycles. 16

The Stirling and Ericsson cycles give a message: Regeneration can

Both the Stirling and Ericsson cycles are totally reversible, as is

the Stirling cycle, except that the two constantvolume processes

17 The Stirling and Ericsson cycles give a message: Regeneration can increase efficiency. Both the Stirling and Ericsson cycles are totally reversible, as is the Carnot cycle, and thus: The Ericsson cycle is very much like the Stirling cycle, except that the two constantvolume processes are replaced by two constant-pressure processes. The execution of the Stirling cycle. A steady-flow Ericsson engine. 17

18 BRAYTON CYCLE: THE IDEAL CYCLE FOR GAS-TURBINE ENGINES The combustion process is replaced by a constant-pressure heat-addition process from an external source, and the exhaust process is replaced by a constant-pressure heat-rejection process to the ambient air. 1-2 Isentropic compression (in a compressor) 2-3 Constant-pressure heat addition 3-4 Isentropic expansion (in a turbine) 4-1 Constant-pressure heat rejection An open-cycle gas-turbine engine. A closed-cycle gas-turbine engine. 18

19 Pressure ratio T-s and P-v diagrams for the ideal Brayton cycle. Thermal efficiency of the ideal Brayton cycle as a function of the pressure ratio. 19

20 The two major application areas of gasturbine engines are aircraft propulsion and electric power generation. The highest temperature in the cycle is limited by the maximum temperature that the turbine blades can withstand. This also limits the pressure ratios that can be used in the cycle. The air in gas turbines supplies the necessary oxidant for the combustion of the fuel, and it serves as a coolant to keep the temperature of various components within safe limits. An air fuel ratio of 50 or above is not uncommon. The fraction of the turbine work used to drive the compressor is called the back work ratio. 20

21 Development of Gas Turbines 1. Increasing the turbine inlet (or firing) temperatures 2. Increasing the efficiencies of turbomachinery components (turbines, compressors): 3. Adding modifications to the basic cycle (intercooling, regeneration or recuperation, and reheating). Deviation of Actual Gas- Turbine Cycles from Idealized Ones Reasons: Irreversibilities in turbine and compressors, pressure drops, heat losses Isentropic efficiencies of the compressor and turbine The deviation of an actual gasturbine cycle from the ideal Brayton cycle as a result of irreversibilities. 21

THE BRAYTON CYCLE WITH REGENERATION In gas-turbine engines, the temperature of the exhaust gas leaving the turbine is often considerably higher than the temperature of the air leaving the compressor.

22 THE BRAYTON CYCLE WITH REGENERATION In gas-turbine engines, the temperature of the exhaust gas leaving the turbine is often considerably higher than the temperature of the air leaving the compressor. Therefore, the high-pressure air leaving the compressor can be heated by the hot exhaust gases in a counter-flow heat exchanger (a regenerator or a recuperator). The thermal efficiency of the Brayton cycle increases as a result of regeneration since less fuel is used for the same work output. T-s diagram of a Brayton cycle with regeneration. A gas-turbine engine with regenerator. 22

23 Effectiveness of regenerator Effectiveness under coldair standard assumptions Under cold-air standard assumptions T-s diagram of a Brayton cycle with regeneration. The thermal efficiency depends on the ratio of the minimum to maximum temperatures as well as the pressure ratio. Regeneration is most effective at lower pressure ratios and low minimum-tomaximum temperature ratios. Can regeneration be used at high pressure ratios? Thermal efficiency of the ideal Brayton cycle with and without regeneration. 23

24 THE BRAYTON CYCLE WITH INTERCOOLING, REHEATING, AND REGENERATION For minimizing work input to compressor and maximizing work output from turbine: A gas-turbine engine with two-stage compression with intercooling, twostage expansion with reheating, and regeneration and its T-s diagram. 24

25 Multistage compression with intercooling: The work required to compress a gas between two specified pressures can be decreased by carrying out the compression process in stages and cooling the gas in between. This keeps the specific volume as low as possible. Multistage expansion with reheating keeps the specific volume of the working fluid as high as possible during an expansion process, thus maximizing work output. Intercooling and reheating always decreases the thermal efficiency unless they are accompanied by regeneration. Why? Comparison of work inputs to a single- stage compressor (1AC) and a two-stage compressor with intercooling (1ABD). As the number of compression and expansion stages increases, the gas-turbine cycle with intercooling, reheating, and regeneration approaches the Ericsson cycle. 25

IDEAL JET-PROPULSION CYCLES Gas-turbine engines are widely used to power aircraft because they are light and compact and have a high power-to-weight ratio.

26 IDEAL JET-PROPULSION CYCLES Gas-turbine engines are widely used to power aircraft because they are light and compact and have a high power-to-weight ratio. Aircraft gas turbines operate on an open cycle called a jet-propulsion cycle. The ideal jet-propulsion cycle differs from the simple ideal Brayton cycle in that the gases are not expanded to the ambient pressure in the turbine. Instead, they are expanded to a pressure such that the power produced by the turbine is just sufficient to drive the compressor and the auxiliary equipment. The net work output of a jet-propulsion cycle is zero. The gases that exit the turbine at a relatively high pressure are subsequently accelerated in a nozzle to provide the thrust to propel the aircraft. Aircraft are propelled by accelerating a fluid in the opposite direction to motion. This is accomplished by either slightly accelerating a large mass of fluid (propeller-driven engine) or greatly accelerating a small mass of fluid (jet or turbojet engine) or both (turboprop engine). In jet engines, the hightemperature and highpressure gases leaving the turbine are accelerated in a nozzle to provide thrust. 26

27 Thrust (propulsive force) Propulsive power Propulsive efficiency Propulsive power is the thrust acting on the aircraft through a distance per unit time. Basic components of a turbojet engine and the T-s diagram for the ideal turbojet cycle. 27

28 28

Modifications to Turbojet Engines The first airplanes built were all propeller-driven, with propellers powered by engines essentially identical to automobile engines.

29 Modifications to Turbojet Engines The first airplanes built were all propeller-driven, with propellers powered by engines essentially identical to automobile engines. Both propeller-driven engines and jet-propulsion-driven engines have their own strengths and limitations, and several attempts have been made to combine the desirable characteristics of both in one engine. Two such modifications are the propjet engine and the turbofan engine. The most widely used engine in aircraft propulsion is the turbofan (or fanjet) engine wherein a large fan driven by the turbine forces a considerable amount of air through a duct (cowl) surrounding the engine. A turbofan engine. 29

30 30

31 Various engine types: Turbofan, Propjet, Ramjet, Sacramjet, Rocket A turboprop engine. A ramjet engine. 31

32 SECOND-LAW ANALYSIS OF GAS POWER CYCLES Exergy destruction for a closed system For a steadyflow system Steady-flow, one-inlet, one-exit Exergy destruction of a cycle For a cycle with heat transfer only with a source and a sink Stream exergy Closed system exergy A second-law analysis of these cycles reveals where the largest irreversibilities occur and where to start improvements. 32

33 Summary Basic considerations in the analysis of power cycles The Carnot cycle and its value in engineering Air-standard sssumptions An overview of reciprocating engines Otto cycle: The ideal cycle for spark-ignition engines Diesel cycle: The ideal cycle for compression-ignition engines Stirling and Ericsson cycles Brayton cycle: The ideal cycle for gas-turbine engines The Brayton cycle with regeneration The Brayton cycle with intercooling, reheating, and regeneration Ideal jet-propulsion cycles Second-law analysis of gas power cycles 33

Chapter 9 GAS POWER CYCLES

Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 9 GAS POWER CYCLES Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction