Centrifugal pumps type T. Version

Transcription

1 type T Version 4-215

2 Content Layout and areas of application for the KNOLL centrifugal pump... 3 Pump overview... 4 Type key and standard multirange motors... 5 Clean coolant pump TG Clean coolant pump TG Clean coolant pump TG Clean coolant pump TG Clean coolant pump TG Clean coolant pump TG Clean coolant pump TG Dirt coolant pump TF Dirt coolant pump TF Dirt coolant pump TS Dirt coolant pump TSK Dirt coolant pump TSK Shredder pump TSC

3 KNOLL centrifugal pumps are submersible pumps. They are mounted on pressureless containers and submersed in the fluid. These flow machines are used primarily on machine tools to convey cooling lubricants. As backflow pumps, they transport the chips/cooling lubricant mixture to filters/separators. They then supply the machines again with the cleaned cooling lubricant. Thanks to their solid and robust construction, the KNOLL coolant pumps have a high load capacity and a long service life. There are 5 different configurations: Type TG with closed impeller For cleaned cooling lubricant with residual dirt Type TF with non-clogging impeller For contaminated cooling lubricant Type TS with helical impeller For contaminated cooling lubricant with air Type TSK with short helical impeller For contaminated cooling lubricant with short chips Type TSC with helical impeller and chopper For contaminated cooling lubricant with long aluminum chips 3

4 Clean coolant pump type TG 6 5 Delivery rate Q [l/min] TG 32 TG 25 4 Delivery head H [m] TG 4 TG 3 TG 5 TG 31 TG Delivery rate Q [m³/h] Dirt cooling lubricant pump types TF, TS, TSK, TSC 6 Delivery rate Q [l/min] Delivery head H [m] TSK 65 TF 5 TSC 65 TF 4, TS 4 TSK Delivery rate Q [m³/h] 4

5 Type code TSC / Submersible pump type Model Impeller index Motor power x 1 Immersion depth in mm Application example TSC / TSC Submersible pump type 65 Size 63 Impeller index Ø 163 mm 75 Motor power 7.5 kw 36 Immersion depth 36 mm Drives Standard multirange motors Three-phase motor 2-pole, heat class ISO-F, protection type IP54, IE2.37 kw to 3. kw 4. kw to 7.5 kw 23 V ( ) / 4 V (Υ), 5 Hz, 2,9 min-¹ 4 V ( ) / 69 (Υ), 5 Hz, 2,9 min-¹ 265 V ( ) / 46 V (Υ), 6 Hz, 3,5 min-¹ 46 V ( ), 5 Hz, 3,5 min-¹ Other voltages and efficiency classes on request. Technical data for the IEC/EN 634 standard Switch-on frequency: In order to minimize the stress to the pump and motor, the switch-on frequency should not exceed once per minute. When switching the pump on and off at shorter intervals, allow it to reach full speed. Rated power Switch frequency.1 kw to 2.6 kw 6 x / hour 3. kw to 5.5 kw 4 x / hour 7.5 kw to 1. kw 2 x / hour > 1. kw 15 x / hour Note: The following characteristic curves refer to 5 Hz speed and cooling lubricant (emulsion) with 1 mm²/s. Characteristic curves for other media, speeds, and viscosities on request. 5

6 TG 2 Clean coolant pump KNOLL clean coolant pumps of type TG are cooling lubricant pumps that convey slightly contaminated media. These pumps are in a position to supply machines with cleaned cooling lubricant (incl. residual dirt). Properties - No seal - Extended, overhung motor shaft with circlip - Open impeller - Impeller material GJL-2 Maximum performance data Air portion 1 Vol.-% Delivery rate 1 l/min Delivery head 6.5 m Particle size 1 mm Chip length 3 mm 7 Fluid level 5 H 4 Rp 3/4" min. fluid level T Minimum level TG 2 clean coolant pump

7 Characteristic curves 7,5 Delivery rate Q [l/min] , 4,5 Delivery head H [m] 3, 1,5,,4 Ø74 Ø71,3 Ø74 Power consumption P [kw],2,1, 1,2 2,4 3,6 4,8 6 Delivery rate Q [m³/h] Ø71 Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TG 2-71 / ,8,37 55 TG 2-74 / ,8,37 55 TG 2-71 / ,3,37 55 TG 2-74 / ,3,37 55 TG 2 clean coolant pump 7

8 TG 25 Clean coolant pump KNOLL clean coolant pumps of type TG are cooling lubricant pumps that convey slightly contaminated media. These pumps are in a position to supply machines with cleaned cooling lubricant (incl. residual dirt). Properties - No seal - Extended, overhung motor shaft with circlip - Very high efficiency thanks to favorably-shaped impeller for optimal flow behavior - Closed impeller - Impeller material GJL-25 Maximum performance data Air portion 1 Vol.-% Delivery rate 2 l/min Delivery head 59 m Particle size 1 mm Chip length 3 mm Rp 1" Fluid level 4 1 min. fluid level T H Minimum level 4 NW 4 8 TG 25 clean coolant pump

9 Characteristic curves 7 Delivery rate Q [l/min] Ø28 3 Ø195 Delivery head H [m] Ø28 Ø158 Ø168 Ø195 Ø179 3 Ø179 Power consumption P [kw] 2 1 Ø168 Ø Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TG / ,2 62 TG / , 66 TG / ,2 62 TG / , 66 TG 25 clean coolant pump 9

10 TG 3 Clean coolant pump KNOLL clean coolant pumps of type TG are cooling lubricant pumps that convey slightly contaminated media. These pumps are in a position to supply machines with cleaned cooling lubricant (incl. residual dirt). Properties - No seal - Extended, overhung motor shaft with circlip - Very high efficiency thanks to favorably-shaped impeller for optimal flow behavior - Closed impeller - Impeller material POM Maximum performance data Air portion 1 Vol.-% Delivery rate 35 l/min Delivery head 28 m Particle size 1 mm Chip length 3 mm Rp 1 1/4" Fluid level H 245 min. fluid level T 295 Minimum level 6 Rp 2" 1 TG 3 clean coolant pump

11 Characteristic curves 35 Delivery rate Q [l/min] Ø Ø144 Delivery head H [m] Ø114 Ø14 Ø124 Ø134 Ø154 Ø144 2 Ø134 Power consumption P [kw] 1 Ø124 Ø114 Ø Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TG 3-.. / ,75 6 TG 3-.. / ,1 6 TG 3-.. / ,5 62 TG 3-.. / ,2 62 TG 3-.. / ,75 6 TG 3-.. / ,1 6 TG 3-.. / ,5 62 TG 3-.. / ,2 62 TG 3-.. / ,5 62 TG 3-.. / ,2 62 TG 3 clean coolant pump 11

12 TG 31 Clean coolant pump KNOLL clean coolant pumps of type TG are cooling lubricant pumps that convey slightly contaminated media. These pumps are in a position to supply machines with cleaned cooling lubricant (incl. residual dirt). Properties - No seal - Extended, overhung motor shaft with circlip - Open impeller - Impeller material GJL-2 Maximum performance data Air portion 1 Vol.-% Delivery rate 3 l/min Delivery head 11 m Particle size 1 mm Chip length 3 mm Fluid level 4 6 min. fluid level H T 3 Rp 1 1/4" Minimum level TG 31 clean coolant pump

13 Characteristic curves 12 Delivery rate Q [l/min] Ø99 Delivery head H [m] 4 2 1, Ø89 Ø99 Power consumption P [kw],5, Delivery rate Q [m³/h] Ø89 Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TG / ,7,75 59 TG / ,7,75 59 TG / ,8,75 59 TG / ,8,75 59 TG / ,3,75 59 TG / ,3,75 59 TG 31 clean coolant pump 13

14 TG 32 Clean coolant pump KNOLL clean coolant pumps of type TG are cooling lubricant pumps that convey slightly contaminated media. These pumps are in a position to supply machines with cleaned cooling lubricant (incl. residual dirt). Properties - No seal - Extended, overhung motor shaft with circlip - Very high efficiency thanks to favorably-shaped impeller for optimal flow behavior - Closed impeller - Impeller material GJL-25 Maximum performance data Air portion 1 Vol.-% Delivery rate 55 l/min Delivery head 6 m Particle size 2 mm Chip length 4 mm Rp 1 1/4" 165,5 269,5 11 Fluid level 4 11 min. fluid level T H Minimum level 5 NW 5 14 TG 32 clean coolant pump

15 Characteristic curves 7 Delivery rate Q [l/min] Delivery head H [m] Ø166 Ø186 Ø178 Ø174 Ø22 Ø192 Ø29 8 Ø192 Ø22 Ø29 Power consumption P [kw] Ø186 Ø178 Ø174 Ø Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TG / ,5 72 TG / ,5 72 TG / ,5 72 TG / ,5 72 TG 32 clean coolant pump 15

16 TG 4 Clean coolant pump KNOLL clean coolant pumps of type TG are cooling lubricant pumps that convey slightly contaminated media. These pumps are in a position to supply machines with cleaned cooling lubricant (incl. residual dirt). Properties - No seal - Extended, overhung motor shaft with circlip - Very high efficiency thanks to favorably-shaped impeller for optimal flow behavior - Closed impeller - Impeller material POM/GJL-25 - Optionally with installed inducer, for improvement of the intake behavior in case of coolant containing a lot of air Maximum performance data Air portion 1 Vol.-% (15 Vol.-% with inducer) Delivery rate 4 l/min Delivery head 32 m Particle size 3 mm Chip length 6 mm Rp 1 1/2" Fluid level min. fluid level H T 295 Minimum level 6 Rp 2" 16 TG 4 clean coolant pump

17 Characteristic curves Delivery rate Q [l/min] Power consumption P [kw] Delivery head H [m] Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TG 4-.. / ,1 6 TG 4-.. / ,5 62 TG 4-.. / ,2 62 TG 4-.. / , 66 TG 4-.. / ,1 6 TG 4-.. / ,5 62 TG 4-.. / ,2 62 TG 4-.. / , 66 TG 4-.. / ,5 62 TG 4-.. / ,2 66 TG 4-.. / , 66 TG 4 clean coolant pump 17

18 TG 5 Clean coolant pump KNOLL clean coolant pumps of type TG are cooling lubricant pumps that convey slightly contaminated media. These pumps are in a position to supply machines with cleaned cooling lubricant (incl. residual dirt). Thanks to their solid and robust construction, the KNOLL centrifugal pumps have a high load capacity and a long service life. Properties - No seal - Extended, overhung motor shaft with circlip - Very high efficiency thanks to favorably-shaped impeller for optimal flow behavior - Closed impeller - Impeller material GJL-25 - Optionally with installed inducer, for improvement of the intake behavior in case of coolant containing a lot of air Maximum performance data Air portion 1 Vol.-% (15 Vol.-% with inducer) Delivery rate 1,4 l/min Delivery head 26 m Particle size 15 mm Chip length 25 mm Rp 2" Fluid level H min. fluid level T 5 65 Minimum level 65 NW TG 5 clean coolant pump

19 Characteristic curves Delivery rate Q [l/min] Ø142 Delivery head H [m] 5 8 Ø11 Ø12 Ø128 Ø137 Ø142 Ø137 6 Ø128 Power consumption P [kw] Ø12 4 Ø11 2, 12, 24, 36, 48, 6, 72, 84, 96, Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TG 5-.. / , 68 TG 5-.. / ,5 68 TG 5-.. / , 68 TG 5-.. / ,5 68 TG 5 clean coolant pump 19

20 TF 4 Dirt coolant pump KNOLL dirt coolant pumps of type TF are cooling lubricant pumps that convey contaminated coolant. These pumps are in a position to transport the chip/cooling lubricant mixture to filters or separators. Properties - No seal - Extended, overhung motor shaft with circlip - Non-clogging impeller - Impeller material POM/GJL-25 - Optionally with installed inducer, for improvement of the intake behavior in case of very contaminated coolants Maximum performance data Air portion 1 Vol.-% (15 Vol.-% with inducer) Delivery rate 65 l/min Delivery head 18 m Particle size 15 mm Chip length 4 mm Chip freight 2 g/l Rp 1 1/2" Fluid level 4 11 min. fluid level T H Minimum level 6 Rp 2" 2 TF 4 dirt coolant pump

21 Characteristic curves 2 Delivery rate Q [l/min] Ø115 8 Ø15 Delivery head H [m] 4 4 Ø65 Ø75 Ø8 Ø85 Ø95 Ø115 3 Ø15 Ø95 Power consumption P [kw] 2 1 Ø85 Ø8 Ø75 Ø Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise [mm] [mm] [kg] [kw] level [db(a)] TF 4-.. / ,75 6 TF 4-.. / ,1 6 TF 4-.. / ,5 62 TF 4-.. / ,2 62 TF 4-.. / , 66 TF 4-.. / ,75 6 TF 4-.. / ,1 6 TF 4-.. / ,5 62 TF 4-.. / ,2 62 TF 4-.. / , 66 TF 4-.. / ,5 62 TF 4-.. / ,2 62 TF 4-.. / , 66 TF 4 dirt coolant pump 21

22 TF 5 Dirt coolant pump KNOLL dirt coolant pumps of type TF are cooling lubricant pumps that convey very contaminated coolant. These pumps are in a position to transport the chip/cooling lubricant mixture to filters or separators. Properties - No seal - Extended, overhung motor shaft with circlip - Non-clogging impeller - Impeller material GJL-25 - Optionally with installed inducer, for improvement of the intake behavior in case of coolant containing a lot of air Maximum performance data Air portion 1 Vol.-% (15 Vol.-% with inducer) Delivery rate 1,2 l/min Delivery head 26 m Particle size 3 mm Chip length 7 mm Chip freight 5 g/l Rp 2" Fluid level H min. fluid level T Minimum level 75 Rp 1 1/2" 22 TF 5 dirt coolant pump

23 Characteristic curves 3 Delivery rate Q [l/min] Ø14 2 Ø13 15 Delivery head H [m] Ø12 Ø11 Ø1 Power consumption P [kw] Ø14 Ø13 Ø12 Ø11 Ø Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TF 5-.. / , 68 TF 5-.. / ,5 68 TF 5-.. / , 68 TF 5-.. / ,5 68 TF 5 dirt coolant pump 23

24 TS 4 Dirt coolant pump KNOLL dirt coolant pumps of type TS are cooling lubricant pumps that convey very contaminated coolant. These pumps are in a position to transport the chip/cooling lubricant mixture to filters or separators. Properties - No seal - Extended, overhung motor shaft with circlip - High load capacity due to solid shaft-hub connection - Helical impeller - Impeller material ST - With integrated inducer, for improvement of the intake behavior in case of very contaminated coolants Maximum performance data Air portion 5 Vol.-% Delivery rate 55 l/min Delivery head 18 m Particle size 12 mm Chip length 2 mm Chip freight 2 g/l Rp 1 1/2" Fluid level 4 H min. fluid level T 295 Minimum level 6 Rp 2" 24 TF 4 dirt coolant pump

25 Characteristic curves 2 Delivery rate Q [l/min] Ø121 8 Delivery head H [m] 4 4 Ø121 3 Power consumption P [kw] Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TS 4-21 / ,2 62 TS 4-21 / , 66 TS 4-21 / ,2 62 TS 4-21 / , 66 TS 4-21 / ,2 62 TS 4-21 / , 66 TF 4 dirt coolant pump 25

26 TSK 4 Dirt coolant pump KNOLL dirt coolant pumps of type TSK are cooling lubricant pumps that convey very contaminated coolant. These pumps are in a position to transport the chip/cooling lubricant mixture with abrasive chips to filters or separators. Properties - No seal - Extended, overhung motor shaft with circlip - High load capacity due to solid shaft-hub connection - Wear-resistant components - Helical impeller - Impeller material ST Maximum performance data Air portion 3 Vol.-% Delivery rate 6 l/min Delivery head 17 m Particle size 2 mm Chip length 4 mm Chip freight 5 g/l Rp 1 1/2" Fluid level 4 8 min. fluid level T H Minimum level TSK 4 dirt coolant pump

27 Characteristic curves 2 Delivery rate Q [l/min] Ø121 Delivery head H [m] 4 4 Ø91 Ø11 Ø111 Ø121 3 Power consumption P [kw] 2 1 Ø111 Ø11 Ø Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TSK 4-.. / ,2 6 TSK 4-.. / , 6 TSK 4-.. / ,2 6 TSK 4-.. / , 6 TSK 4-.. / ,2 62 TSK 4-.. / , 62 TSK 4 dirt coolant pump 27

28 TSK 65 Dirt coolant pump KNOLL dirt coolant pumps of type TSK are cooling lubricant pumps that convey very contaminated coolant. These pumps are in a position to transport the chip/cooling lubricant mixture with abrasive chips to filters or separators. Properties - Energy-efficient when used with frequency inverter - Flexible layout with standard motors - No seal - Wear-resistant components - Half-open impeller - Impeller material ST - With upstream inducer, for improvement of the intake behavior in case of coolant containing a lot of air Maximum performance data Air portion 3 Vol.-% Delivery rate 1,5 l/min Delivery head 38 m Particle size 2 mm Chip length 4 mm Chip freight 1 g/l Fluid level 8 min. fluid level 4 H 35 5 T Rp 2 1/2" 121 Minimum level TSK 65 dirt coolant pump

29 Characteristic curves 5 Delivery rate Q [l/min] Delivery head H [m] 1 8 Ø15 Ø163 Ø178 Ø193 Ø193 6 Ø178 Power consumption P [kw] 4 2 Ø163 Ø Delivery rate Q [m³/h] Variants Type T H Weight Motor power Noise level [mm] [mm] [kg] [kw] [db(a)] TSK / ,5 68 TSK / ,5 68 TSK / ,5 68 TSK / ,5 68 TSK 65 dirt coolant pump 29

30 TSC 65 Shredder pump KNOLL shredder pumps of type TSC are cooling lubricant pumps with an integrated chopper for aluminum chips. The pumps are in a position to shred long aluminum chips to a pump-appropriate size and convey them with cooling lubricant to the central preparation station. An additional chip reducer is therefore superfluous. Properties - Energy-efficient when used with frequency inverter - Flexible layout with standard motors - Bearing protected by rotary shaft seal - Rigid shaft due to bearing of the cutting head in a ceramic precision bearing - Durable and low-maintenance due to hardened hydraulic and reducer components - Half-open impeller - Impeller material ST Maximum performance data Air portion 25 Vol.-% Delivery rate 1, l/min Delivery head 2 m Chip thickness.5 mm Chip freight 1 g/l Container design Minimum volume 25 l Minimum wall thickness 5 mm G2 1/2" (17*) Fluid level H min. fluid level T Minimum level * Dimension valid for TSC 65-../ TSC 65 shredder pump

31 Characteristic curves Delivery rate Q [l/min] Delivery head H [m] 5 8 Ø163 Ø15 6 Ø163 Power consumption P [kw] Delivery rate Q [m³/h] Ø15 Variants Type T H Weight Motor power [mm] [mm] [kg] [kw] TSC 65-5/ ,5 TSC 65-63/ ,5 TSC 65-5/ ,5 TSC 65-63/ ,5 TSC 65 shredder pump 31

32 KNOLL Maschinenbau GmbH Schwarzachstraße 2 DE Bad Saulgau Tel () 75 81/2 8- Fax + 49 () 75 81/ info.itworks@knoll-mb.de T Right reserved to modify technical details.