ADVANCED LINE. All airmotors can also be used without lubrication.

Transcription

1 Screwdriving technology Automation Air motors Air tools ADVANCED LINE Stainless Steel Air s from 20 W / 0.03 Hp up to 1.2 kw / 1.6 Hp NEW MOTOR RANGE High torque motors made from stainless steel: Our ADVANCED LINE pneumatic motors are now available as high torque motors made from stainless steel. The ideal drive solution for e.g. agitators and industrial mixers. non corrosive ATEX conform oil-free sealed sterilisable compact insensitive to cleaning solvents The ADVANCED LINE air motors are particularly suitable for use in the food industry, medical technology, underwater applications and the chemical industry. All airmotors can also be used without lubrication. All external parts (housing and spindle) of our ADVANCED LINE series are made from high quality non corrosive steel. Our air motors are also available in an ATEX conform complete system with integrated holding brakes. In addition our modular principle enables us to offer low cost customisations for your specific application! D 6400 E

2 PRODUCT SPECTRUM OVERVIEW: ADVANCED LINE AIR MOTORS Stainless steel motors with integrated planetary gears The vane motors of the ADVANCED LINE are particularly compact drive solutions for installation in either handheld machines or industrial systems. These top quality stainless steel motors are suitable for the chemical industry, for the paper industry, the pharmaceutical industry, medical technology and also for use in the food industry. Performance classes: 20 W Page 4 30 W Page 4 80 W Page W Page W Page W Page W Page W Page kw Page 20 High torque stainless steel motors The high torque motors of the ADVANCED LINE are small in size but provide extremely high output. Our high torque motors are also less apt to stall, the stalling torque for e.g. motor type is 800 Nm / in.lbs. These drive solutions are particularly suitable for use in industrial agitators and mixers as used in the paint industry, food industry or pharmaceutical industry. Performance classes: 285 W Page W Page W Page 18 Stainless steel motors with integrated holding brake Due to their size and design DEPRAG stainless steel motors with integrated holding brake are the optimal choice for use in any application where reliability plays an important role. The integrated holding brake can either be controlled using a separate control lead or via the motor exhaust. If pressure falls the brakes are automatically activated. The big plus: This innovative complete system is also available with ATEX certification! Performance classes: 200 W Page W Page kw Page 22 2

3 ADVANTAGES OF ADVANCED LINE AIR MOTORS LONG LIFE-SPAN A wide product range of stainless steel motors, the use of DEPRAG high performance vanes as well as a specific surface coating on our materials all this ensures your motor's long life-span. Airmotor - gear box - valve: a stainless steel system for the paper industry, sealed stainless steel motors, high performance vanes SHORT DELIVERY TIMES Due to our large amount of in-house production we are able to deliver quickly and flexibly at short notice, even when dealing with smaller quantities. Large amount of in-house production, on-site salt bath heat treatment facility APPLICATION CONSULTANCY Our application engineers will gladly advise you in the selection of the most suitable drive for your application. If you would like to test or replace your existing drive we can check it for you in our innovative performance testing facility. Performance testing facility, professional guidance from our engineers WIDE VARIETY AND COMPREHENSIVE RANGE OF ACCESSORIES Our standard programme is distinguished by its wide variety. All our stainless steel motors are also available with threaded spindle. Additionally due to our modular principle we are able to offer numerous variations to choose from. Do not hesitate to contact us if you have a specific mounting fixture request. Individual customisation at an attractive price 3

4 20 W / 30 W ADVANCED LINE AIR MOTOR size 0 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. Type Part no B C D E Nominal-Power W / HP 20 / / / / 0.03 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 0.06 / / / / 3.5 Start torque min. Nm / in.lbs 0.09 / / / / 5.3 Air consumption m 3 /min / cfm 0.1 / / / / 3 Weight kg / lbs 0.16 / / / / 0.3 Hose I.D. mm / in. 3 / 1 /8 3 / 1 /8 3 / 1 /8 3 / 1 /8 Included in delivery: 2 Slide connectors (M 5) size 0 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. Included in delivery: 1 Slide connector (M 5) right rotation Type R R Part no B E Nominal-Power W / HP 30 / / 0.04 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 0.08 / / 5 Start torque min. Nm / in.lbs 0.12 / / 7.5 Air consumption m 3 /min / cfm 0.1 / / 3 Weight kg / lbs 0.13 / / 0.29 Hose I.D. mm / in. 3 / 1 /8 3 / 1 /8 Optional Equipment for size 0 right rotation Flange Part no necessary 3 cylinder-screws Part no Silencer (M 5) Part no Maintenance unit with lubricator* Part no A A Connection thread G 1/4 G 1/4 Maintenance unit without lubricator* Part no A A Connection thread G 1/4 G 1/4 Replacement part set consisting of: vanes, sealant rings, o-rings and silencers Part no B B *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page 25. 4

5 size 0 A R ø4 k ø8 e8 ø17 e8 A1 (Chucking range) 10 ø17 M5 ( left rotation) M5 ( right rotation) M Exhaust air ø12 (hole pattern) Silencer (Optional equipment) 13.5 A2 size 0 right rotation ø 4 k ø8 e8 ø17 e8 A1 (Chucking range) ø17 M5 ( right rotation) M Exhaust air ø12 (hole pattern) 2 Flange (Optional equipment) ø 20 e8 ø 6 ø 8 H7 ø 32 ø ø 3.2 Dimensions in mm p size 0 Type A1 Dimensions of motor (mm) R R A2 5

6 80 W ADVANCED LINE AIR MOTOR size 1 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. Type Part no A B C D E Nominal-Power W / HP 80 / / / / / 0.11 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 0.06 / / / / 11 2 / 17.7 *) Start torque min. Nm / in.lbs 0.09 / / / / 16 2 / 17.7 *) Air consumption m 3 /min / cfm 0.23 / / / / / 8 Length L mm / in / / / / / 4.4 Weight kg / lbs 0.2 / / / / / 0.6 Hose I.D. mm / in. 4 / 5 /32 4 / 5 /32 4 / 5 /32 4 / 5 /32 4 / 5 /32 *) max. admissible torque Optional Equipment for size 1 Flange Part no necessary 3 cylinder-screws Part no Bracket Part no necessary 3 cylinder-screws Part no Slide connectors (M8 x 0.75) Part no. included in delivery 2 Silencer Part no necessary 2 Slide connectors Part no Hose 0.2 m Part no Maintenance unit with lubricator* Part no A Connection thread G 1/4 Maintenance unit without lubricator* Part no A Connection thread G 1/4 Replacement part set consisting of: vanes, sealant rings, o-rings and silencers Part no B *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page 25. 6

7 size 1 Air supply left rotation M8x0.75 Air supply right rotation M8x L ø 6 k ø13 e8 M3 6 Exhaust air M8x (Chucking range) ø40 ø13 H8 ø 30 ±0.1 5 ø ø13 H ø 22 e9 ø 15 (hole pattern) 20 4 ø Dimensions in mm p

8 120 W ADVANCED LINE AIR MOTOR size 2 II 2 GD c IIC Type T6 (80 C) Part no A H B C D E F Nominal-Power W / HP 120 / / / / / / / ) Nominal-Speed rpm ) Speed (idling) rpm Nominal-Torque Nm / in.lbs 0.10 / / / / / / 34 5 / 44*) Start torque min. Nm / in.lbs 0.15 / / / / / 34 5 / 44*) 5 / 44*) Air consumption m 3 /min / cfm 0.3 / / / / / / / 11 Weight kg / lbs 0.35 / / / / / / / 1 Hose I.D. mm / in. 6 / ¼ 6 / ¼ 6 / ¼ 6 / ¼ 6 / ¼ 6 / ¼ 6 / ¼ Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. *) max. admissible torque 1) theoretical values for issuing the power diagram Optional Equipment for size 2 Flange Part no necessary 4 cylinder-screws Part no Bracket Part no necessary 4 cylinder-screws Part no Silencer: motor operates in one direction 1 Hose nozzle Part no Silencer Part no Silencer: motor is (right and left rotation) 2 Hose nozzles Part no Silencer Part no Maintenance unit with lubricator* Part no A Connection thread G 1/4 Maintenance unit without lubricator* Part no A Connection thread G 1/4 Replacement part set consisting of: vanes, sealant rings, o-rings and silencers Part no A *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page 25. 8

9 size 2 A1 A2 left rotation G1/8 14 right rotation G1/8 17 A3 - Chucking Range ø2 h9 M4 ø 8 k6 4 8 Exhaust air G1/8 A2x2x14 5 ø13 e8 ø27 e8 M3x ø21 3 Flange (Optional equipment) ø29 ø13 H8 Silencer (Optional equipment) ø40 ø ø4.5 Bracket (Optional equipment) ø29 ø13 H8 ø Dimensions in mm p size 2 Dimensions of motor (mm) Type A1 A2 A

10 200 W / 300 W ADVANCED LINE DRUCKLUFTMOTOR size 2.5 II 2 GD c IIC Type T6 (80 C) Part no B C D F E A G H Nominal-Power W / HP 200 / / / / / / / / ) Nominal-Speed rpm ) Speed (idling) rpm Nominal-Torque Nm / in.lbs 0.26 / / / / / / / / 177*) Start torque min. Nm / in.lbs 0.4 / / / / / / / / 177*) Air consumption m 3 /min / cfm 0.37 / / / / / / / / 13 Weight kg / lbs 0.7 / / / / / / / / 2.1 Hose I.D. mm /in. 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. *) max. admissible torque 1) theoretical values for issuing the power diagram size 3 II 2 GD c IIC Type T6 (80 C) Part no A B C D E F G K H Nominal-Power W / HP 300 / / / / / / / / ) 280/ ) Nominal-Speed rpm ) Speed (idling) rpm Nominal-Torque Nm / in.lbs 0.4 / / / / / / / / 319*) 36 / 319*) Start torque min. Nm / in.lbs 0.6 / / / / / / / / 319*) 36 / 319*) Air consumption m 3 /min / cfm 0.47 / / / / / / / / / 17 Weight kg / lbs 1.0 / / / / / / / / / 2.7 Hose I.D. mm / in. 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. *) max. admissible torque 1) theoretical values for issuing the power diagram Optional Equipment for size 2.5 for size 3 Flange Part no necessary 4 cylinder-screws Part no Bracket Part no necessary 4 cylinder-screws Part no Silencer: motor operates in one direction 1 Hose nozzle Part no ( 1 /8 ) ( 1 /4 ) 1 Silencer Part no ( 1 /8 ) ( 1 /4 ) 1 Silencer Part no ( 1 /4 ) ( 1 /4 ) Silencer: motor is 2 Hose nozzles Part no ( 1 /8 ) ( 1 /4 ) 1 Silencer Part no ( 1 /4 ) ( 1 /4 ) Maintenance unit with lubricator* Part no A A Connection thread G 1/4 G 1/2 Maintenance unit without lubricator* Part no A A Connection thread G 1/4 G 1/2 Replacement part set consisting of: vanes, sealant rings, o-rings and silencers Part no A A *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page

11 size 2.5 and size 3 left rotation D1 D3 right rotation D1 B2 k6 A2 A1 A4 - Chucking range A3 C4 C2 h9 C5 D2 7 B3 e8 B1 e8 C1 Exhaust air G1/4 E1 Silencer Flange B3 e8 E5 E3 E4 E2 ø5.5 Bracket F3 E5 C3 for motor size 2.5: A3x3x18 for motor size 3: - types /-013/-023/-073: A4x4x20 - types /-093/-0931/-1931/-2931: A5x5x20 ø F1 F2 Dimensions in mm p size Type Dimensions of motor (mm) A1 A2 A3 A4 B1 B2 B3 C1 C2 C3 C4 C5 D1 D2 D M4 1.6 G 1 / M4x M5 G 1 / M5x12 size Type Dimensions of flange (mm) Dimensions of bracket (mm) B3 E1 E2 E3 E4 E5 F1 F2 F

12 285 W ADVANCED LINE HIGH TORQUE MOTOR size 3 with high torque II 2 GD c IIC Type T6 (80 C) Part no I L M N O Nominal-Power W / HP 285 / / / / / 0.37 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 32 / / / / / Start torque min. Nm / in.lbs 47 / / / / / Air consumption m 3 /min / cfm 0.47 / / / / / 16.6 Weight kg / lbs 2.7 / / / / / 7.7 Hose I.D. mm / in. 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. Optional Equipment *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator **) no. of cylinder screws required for size 3 for size 3 Type to Type to Flange Part no necessary cylinder-screws Part no (8 pieces)** (6 pieces)** Bracket Part no necessary cylinder-screws Part no (8 pieces)** (6 pieces)** Silencer: motor operates in one direction 1 Hose nozzle Part no ( 1 /4 ) ( 1 /4 ) 2 Silencer Part no ( 1 /4 ) ( 1 /4 ) Silencer: motor is 2 Hose nozzles Part no ( 1 /4 ) ( 1 /4 ) 1 Silencer Part no ( 1 /4 ) ( 1 /4 ) Maintenance unit with lubricator* Part no A A Connection thread G 1/2 G 1/2 Maintenance unit without lubricator* Part no A A Connection thread G 1/2 G 1/2 Replacement part set consisting of: vanes, sealant rings, o-rings and silencers Part no B C Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page

13 size 3 High torque stainless steel motors left rotation G1/4 20 right rotation G1/4 types /-323/-373: A6x6x32 types /-423: A8x7x32 A2 A1 A4 - Chucking range Pitch: type /-323/-373: 8 x 45 type /-423: 6 x 60 B4 D2 h9 A3 B L Exhaust air G1/4 R D1 B2 k6 32 B3 e8 B1 e8 ø42 d9 B5 Flange C8 C1 e8 C5 C3 C6 9.5 C1 C C3 C1 SW17 Silencer C4 C7 Bracket C2 C4 C3 C ø Dimensions in mm p size 3 Dimensions of motor (mm) Type A1 A2 A3 A4 B1 B2 B3 B4 B5 B6 C1 C2 C3 C4 C5 C6 C7 C8 D1 D M6 M6x M8 M8x

14 200 W / 300 W ADVANCED LINE AIR MOTOR WITH INTEGRATED HOLDING BRAKE size 2.5 with holding brake II 2 GD c IIC Type B B B B B B ATEX conform T6 (80 C) Part no B C D F E A Type B B B B B B Part no B C D F E A Nominal-Power W / HP 200 / / / / / / 0.27 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 0.26 / / / / / / 106 Start torque min. Nm / in.lbs 0.4 / / / / / / 159 Stall-Torque Nm / in.lbs 0.52 / / / / / / 177*) Brake-Torque Nm / in.lbs 1 / / / / / 177*) 20 / 177*) Air consumption m 3 /min / cfm 0.37 / / / / / / 13 Weight kg / lbs 1 / / / / / / 2.5 Hose I.D. mm / in. 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 size 3 with holding brake II 2 GD c IIC Type B B B B B B ATEX conform T6 (80 C) Part no A B C D E F Type B B B B B B Part no A B C D E F Nominal-Power W / HP 300 / / / / / / 0.4 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 0.4 / / / / / / 149 Start torque min. Nm / in.lbs 0.6 / / / / / / 224 Stall-Torque Nm / in.lbs 0.8 / / / / / / 299 Brake-Torque Nm / in.lbs 1 / / / / / / 318.6*) Air consumption m 3 /min / cfm 0.47 / / / / / / 17 Weight kg / lbs 1.35 / / / / / / 3.3 Hose I.D. mm / in. 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 10 / 3 /8 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. *) max. admissible torque Optional Equipment: for size 2.5 for size 3 Flange Part no necessary 4 cylinder-screws Part no Bracket Part no necessary 4 cylinder-screws Part no Silencer: motor operates in one direction 1 Hose nozzle Part no ( 1 /8 ) ( 1 /4 ) 1 Silencer Part no ( 1 /8 ) ( 1 /4 ) 1 Silencer Part no ( 1 /4 ) ( 1 /4 ) Silencer: is 2 Hose nozzles Part no ( 1 /8 ) ( 1 /4 ) 1 Silencer Part no ( 1 /4 ) ( 1 /4 ) Maintenance unit with lubricator* Part no A A Connection thread G 1/4 G 1/2 Maintenance unit without lubricator* Part no A A Connection thread G 1/4 G 1/2 Replacement part set consisting of: vanes, sealant rings, o-rings and silencers Part no A A Replacement part set for brake consisting of: discs, pressure spring and o-rings Part no C C *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page 25. A pressure regulator valve is included within our shipment of the ATEX conform brake motors. This safety valve turns off the air supply in the brake leads automatically when the pressure falls under 5 bar. This prevents an irregular temperatur increase. 14

15 size 2.5 and size 3 with holding break A1 left rotation D1 D3 right rotation D1 A2 A4-Chucking range A3 A5 C2 h9 B1 e8 B2 k6 B3 e8 C3 C1 7 D2 ø C5 Exhaust air G1/4 size 2.5: A3x3x18 size 3: types /-013/-023/-073 B: A4x4x20 types /-093 B: A5x5x20 E1 Pilot air port for motor brake required air pressure > 5 bar (70.8 PSI) C4 Flange Silencer ø5.5 B3 e8 E5 E2 E3 E4 4.5 Bracket ø6.6 F F2 F1 Dimensions in mm p size Dimensions of motor (mm) Type A1 A2 A3 A4 A5 B1 B2 B3 C1 C2 C3 C4 C5 D1 D2 D B B B M4 1.6 G 1 / B B B B B B B M5 M4x12 G 1 / B B M5x12 size Type B B B B B B B B B B B B Dimensions of flange (mm) Dimensions of bracket (mm) B3 E1 E2 E3 E4 E5 F1 F2 F

16 600 W / 900 W ADVANCED LINE AIR MOTOR size 6 II 2 GD c IIC Type T6 (80 C) Part no A H B C D E F G Type B B B B B B B16 for Drill-Chuck Part no H B C D E F G Nominal-Power W / HP 600 / / / / / / / / 0.4 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 0.82 / / / / / / / / 336 Start torque min. Nm / in.lbs 1.23 / / / / / / / / 504 Air consumption m 3 /min / cfm 0.85 / / / / / / / / 19 Weight kg / lbs 2.2 / / / / / / / / 5.9 Hose I.D. mm / in. 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 size 7 II 2 GD c IIC Type T6 (80 C) Part no A H B C D E F Nominal-Power W / HP 900 / / / / / / / 1.2 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 1.4 / / / / / / / Start torque min. Nm / in.lbs 2.1 / / / / / / / 752 Air consumption m 3 /min / cfm 1.4 / / / / / / / 49.4 Weight kg / lbs 2.5 / / / / / / / 6.6 Hose I.D. mm / in. 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. Optional Equipment: for size 6 for size 7 Flange Part no necessary 4 cylinder-screws Part no Bracket Part no necessary 4 cylinder-screws Part no Silencer: motor operates in one direction 1 Hose nozzle Part no ( 3 /8 ) ( 3 /8 ) 1 Silencer Part no ( 3 /8 ) ( 3 /8 ) 1 Silencer Part no ( 1 /2 ) ( 1 /2 ) Silencer: is 2 Hose nozzles Part no ( 3 /8 ) ( 3 /8 ) 1 Silencer Part no ( 1 /2 ) ( 1 /2 ) Drill-Chuck Range 1-13 mm / B 16 Part no Quick change chuck Range 1-13 mm / B 16 Part no Maintenance unit with lubricator* Part no A A Connection thread G 1/2 G 3/4 Maintenance unit without lubricator* Part no A A Connection thread G 1/2 G 3/4 Replacement part set consisting of: Part no A / for Part no A-D, H A / for Part no A-D, H vanes, sealant rings, o-rings and silencers for Part no B-D, H B / for Part no E-F Part no B / for Part no E-G for Part no E-G *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator **) no. of cylinder screws required Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page

17 M6 size 6 and size 7 left rotation G3/8 24 right rotation G3/8 A2 A4 - Chucking range A1 A3 C2 h9 14 ø35 e8 ø56 e8 C B1 k6 Exhaust air G1/2 A1 C3 A2 A B16 to B16 ø35 e8 Silencer Drill chuck cone B16 DIN 238 size 6: types /-016/-026/-036/-046: A5x5x20 types /-066/-0661: A6x6x22 size 7: types /-017/-027/-037/-047: A5x5x20 types /-067: A6x6x22 Flange 7.5 ø85 ø70 ø35 e8 ø ø Bracket ø Dimensions in mm p size 6 7 Dimensions of motor (mm) Type A1 A2 A3 A4 B1 C1 C2 C M5x M6x B B B B B B B M5x M6x12 17

18 570 W / 860 W ADVANCED LINE HIGH TORQUE AIR MOTOR size 6 II 2 GD c IIC Type T6 (80 C) Part no I K L M Nominal-Power W / HP 570 / / / / Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 72 / / / / Start torque min. Nm / in.lbs 108 / / / / 3540 Air consumption m 3 /min / cfm 0.85 / / / / 30 Weight kg / lbs 3.6 / / / / 9.7 Hose I.D. mm / in. 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. size 7 II 2 GD c IIC Type T6 (80 C) Part no I K L M Nominal-Power W / HP 860 / / / / 1.14 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 110 / / / / 3540 Start torque min. Nm / in.lbs 160 / / / / 5310 Air consumption m 3 /min / cfm 1.4 / / / / 49.4 Weight kg / lbs 3.8 / / / / 10.3 Hose I.D. mm / in. 12 / 1 /2 12 / 1 /2 12 / 1 /2 12 / 1 /2 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. Optional Equipment *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator **) no. of cylinder screws required for size 6 / 7 Type to Type Type to Type Flange Part no necessary 4 cylinder-screws Part no (8 pieces)** (6 pieces)** Bracket Part no necessary 4 cylinder-screws Part no (8 pieces)** (6 pieces)** Silencer: motor operates in one direction 1 Hose nozzle Part no ( 3 /8 ) 1 Silencer Part no ( 3 /8 ) 1 Silencer Part no ( 1 /2 ) Silencer: is 2 Hose nozzles Part no ( 3 /8 ) 1 Silencer Part no ( 1 /2 ) for size 6 for size 7 Maintenance unit with lubricator* Part no A A Connection thread G 1/2 G 3/4 Maintenance unit without lubricator* Part no A A Connection thread G 1/2 G 3/4 Replacement part set consisting of: D / for Type to C / for Type to vanes, sealant rings, o-rings and silencers Part no E / for Type D / for Type Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page

19 size 6 and size 7 High torque stainless steel motors left rotation G3/8 right rotation G3/8 Pitch 8x /156/166 8x /157/167 6x /517 A A2 A3 A5-Chucking range B3 e8 A4 B4 D2 h9 14 D1 B2 k6 32 B1 e8 B5 B6 Exhaust air G1/2 types /-517: A8x7x32 all other types: A6x6x C4 Silencer SW17 C7 C6 Flange C8 C1 e8 C5 C1 C3 C2 C3 1.5 C4 1.5 C6 Bracket C1 e8 C5 C3 C ø Dimensions in mm p size 6 Dimensions of motor (mm) Type A1 A2 A3 A4 A5 B1 B2 B3 B4 B5 B6 C1 C2 C3 C4 C5 C6 C7 C8 D1 D e M6 M6x h M8 M8x size 7 Type Dimensions of motor (mm) A1 A2 A3 A4 A5 B1 B2 B3 B4 B5 B6 C1 C2 C3 C4 C5 C6 C7 C8 D1 D e M6 M6x h M8 M8x

20 1200 W ADVANCED LINE AIR MOTOR size 8 II 2 GD c IIC Type T5 (95 C) Part no A B C D E F Nominal-Power W / HP 1200 / / / / / / 0.9 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 2.5 / / / / / / 592 Start torque min. Nm / in.lbs 3.8 / / / / / / 885 Air consumption m 3 /min / cfm 1.6 / / / / / / 39 Weight kg / lbs 5.9 / / / / / / 14.7 Hose I.D. mm / in. 19 / 3 /4 19 / 3 /4 19 / 3 /4 19 / 3 /4 19 / 3 /4 19 / 3 /4 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. Optional Equipment for size 8 Flange Part no necessary 4 cylinder-screws Part no Bracket Part no necessary 4 cylinder-screws Part no Silencer: motor operates in one direction 1 Hose nozzle Part no ( 1 /2 ) 1 Silencer Part no ( 1 /2 ) 1 Silencer Part no ( 3 /4 ) Silencer: motor is 2 Hose nozzles Part no ( 1 /2 ) 1 Silencer Part no ( 3 /4 ) Maintenance unit with lubricator* Part no A Connection thread G 3/4 Maintenance unit without lubricator* Part no A Connection thread G 3/4 Replacement part set consisting of: A / for Part no A-C vanes, sealant rings, o-rings and silencers Part no B / for Part no D-F *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page

21 size left rotation G1/2 39 right rotation G1/2 B1 k6 A2 A4 - Chucking range A1 A3 C2 C3 22 ø50 e8 ø82 e8 Exhaust air G3/4 M8 Flange Silencer ø100 C1 ø68 types /-028/-038: A6x6x32 types /-058/-0581: A8x7x ø50 e8 ø46 ø115 ø9 9.5 Bracket ø Dimensions in mm p size 8 Type Dimensions of motor (mm) A1 A2 A3 A4 B1 C1 C2 C M6x M10x20 21

22 1200 W ADVANCED LINE AIR MOTOR WITH INTEGRATED HOLDING BRAKE ATEX conform size 8 with holding brake II 2 GD c IIC Type B B B B B ATEX conform T5 (95 C) Part no A B C D E Type B B B B B without ATEX-authorization Part no A B C D E Nominal-Power W / HP 1200 / / / / / 1.6 Nominal-Speed rpm Speed (idling) rpm Nominal-Torque Nm / in.lbs 2.5 / / / / / 628 Start-Torque min. Nm / in.lbs 3.8 / / / / / 947 Stall-Torque Nm / in.lbs 5 / / / / / 1256 Brake-Torque Nm / in.lbs 6.2 / / / / / 1566 Air Consumption m 3 /min / cfm 1.6 / / / / / 56 Weight kg / lbs 9 / / / / / 21.3 Hose I.D. mm / in. 19 / 3 /4 19 / 3 /4 19 / 3 /4 19 / 3 /4 19 / 3 /4 Performance data relate to an air pressure of 6 bar (85 PSI) and lubricated air. With oil-free operation the output will be reduced by 10-20%. Optional Equipment for size 8 Flange Part no necessary 4 cylinder-screws Part no Bracket Part no necessary 4 cylinder-screws Part no Silencer: motor operates in one direction 1 Hose nozzle Part no ( 1 /2 ) 1 Silencer Part no ( 1 /2 ) 1 Silencer Part no ( 3 /4 ) Silencer: motor is 2 Hose nozzles Part no ( 1 /2 ) 1 Silencer Part no ( 3 /4 ) Maintenance unit with lubricator* Part no A Connection thread G 3/4 Maintenance unit without lubricator* Part no A Connection thread G 3/4 Replacement part set consisting of: A / for Part no (1) A-C vanes, sealant rings, o-rings and silencers Part no B / for Part no (1) D-F Replacement part set for brake consisting of: discs, o-rings, pressure spring and silencer Part no B *) Maintenance unit consists of pressure regulator valve, filter and optionally with or without lubricator Pressure Regulator Valve Of course you can also purchase individual replacement parts from us. Our standard maintenance units are not ATEX conform. Please contact us if this is a requirement. Allowable shaft loading see page 24. Further notes for soundproofing see page 25. A pressure regulator valve is included within our shipment of the ATEX conform brake motors. This safety valve turns off the air supply in the brake leads automatically when the pressure falls under 5 bar. This prevents an irregular temperatur increase. 22

23 size 8 with holding break types /-028/-038 B: A6x6x32 types /-058 B: A8x7x50 Pilot air port for motor brake required air pressure > 5 bar (70.8 PSI) A1 left rotation G1/2 39 right rotation G1/2 A2 A3-Chucking range C2 h9 C3 22 ø50 e8 B1 k6 ø82 e8 C1 ø Exhaust air G3/4 227 M Flange ø50 e8 ø46 ø100 ø115 Silencer ø9 9.5 Bracket ø Dimensions in mm p size 8 with holding brake Dimensions of motor (mm) Type A1 A2 A3 B1 C1 C2 C B B B M6x B B M10x20 23

24 TECHNICAL DATA Maximum allowable shaft load of the drive shaft F ax flattened shaft size 0 and 1 a F rad s with flattened shaft size Part no. Fax [N] Frad [N] MG B,C,D,E MG E MG A-D Allowable force for 10 million spindle rotations with 90 % survival probability of bearing. a [mm] s with parallel key shaft size Part no. Part no. with holding brake Fax [N] Frad [N] a [mm] MG A-H MG A-H A-F MG A, B MG A-D A-D MG E-H, K E, F MG I, L, M MG N, O MG A-D, H MG E-G MG I, K, L MG M MG A-D, H MG E-F MG I, K, L MG M MG A-C A-C, A-C MG D-F D-E, D-E Allowable force for 10 million spindle rotations with 90 % survival probability of bearing. s with threaded spindle size Part no. Fax [N] Frad [N] MG A-H MG A-L MG A-D MG E-H Allowable force for 10 million spindle rotations with 90 % survival probability of bearing. a [mm] s with drill chuck size Part no. Fax [N] Frad [N] MG B-D, H MG E-G Allowable force for 10 million spindle rotations with 90 % survival probability of bearing. a [mm] 24

25 TECHNICAL DATA Noise level of the motors Noise level for motors of the series 67 - without or with silencer (see optional equipment)) Noise level db (A) for size without silencer Noise level db (A) with silencer Part no. silencer / / / / Optional Silencer sets for further reduction of the noise level Silencer sets for motors of the build series 67 - Attachment for only one rotation direction (clockwise or anticlockwise rotation) for size Part no. Hose length mm Noise level db (A) B B B B B B B Silencer sets for motors of the build series 67 - Attachment adjustable (clockwise and anticlockwise rotation) for size Part no. Hose length mm Noise level db (A) A A A A A A A Silencer Silencer Use in potentially explosive environments The correspondingly marked motors are suitable for use in potentially explosive environments. Speed standard values (rpm) for HSS spiral-drills Cutting 35 m/min 28 m/min 25 m/min 14 m/min 11 m/min 7 m/min 22 m/min 12 m/min 50 m/min 90 m/min 165 m/min 210 m/ min Speed (115 ft./min) (90 ft./min) (80 ft./min) (45 ft./min) (35 ft./min) (23 ft./min) (70 ft./min) (40 ft./min) (165 ft./min) (300 ft./min) (540 ft./min) (690 ft./min) Carbon steel Alloy steel Stainless Cast-Iron Copper Lightweight-Metal Magnesium- Drill up to above steel up to above Bronze common Alloy 2 ) dia Brass alloy hard mm/in. N/mm 2 N/mm 2 N/mm 2 N/mm 2 N/mm 2 N/mm 2 N/mm 2 mild brass 1 ) (30 (30-45 (45 (45-55 (55-70 (10 (10 long tons/ long tons/ long tons/ long tons/ long tons/ long tons/ long tons/ sq. in.) sq. in.) sq. in.) sq. in.) sq. in.) sq. in.) sq. in.) 1/ / 5 / / 1 / / 5 / / 13 / / 15 / / 9 / / 5 / / 23 / / 25 / ) Speed therefore for triplet of duro-plates, hard-paper and hard tissues, however instead of the HSS-drills we recommend quickly steel-drills equipped with hard-metal K 10 2) for thermos-plates, we recommend double the values 25

26 The layout of your air motor: Calculating the motor power P = M x n 9550 P = Power Output in kw M = Nominal-Torque in Nm n = Nominal-Speed in rpm The optimal working range of an air motor is close to the nominal speed. If you need lower speeds than are mentioned in the catalogue you can reduce the speed by throttling the exhaust air with only a slight loss of power. By throttling the supply air or decreasing the operating pressure the speed, torque and power are reduced. All performance data of the DEPRAG air motors is based on operating pressure of 6 bar and the opening cross-section mentioned in the motor data. If your application conditions are different from this then you will find a comprehensive guide to the layout of our motors in brochure D 6000 E. Torque (M) % Power (P) % Air consumption (Q) % Stall torque Nominal power P Q 80 Starting torque M Nominal torque Speed (n) % Nominal speed Speed idling = optimal working range of the air motor 26

27 Do you need support in selecting the right drive system? Tell us your operational conditions and our application consultants will be happy to help: Application: In what kind of environment will the motor be installed? Application conditions: Required turn direction: performance: Performance influencing application conditions: External motor design: Drive spindle design: ATEX requirement / explosion safety? yes no if yes, which safety class: food industry conformity? yes no sterilisable? yes no acid resistant? yes no steam resistant? yes no constant operation (24 hrs, non-stop) yes no duty cycle in hrs/day: days/year: cycle time (s): motor loaded to stall? yes no self-locking? yes no left right (view from air inlet) power: nominal torque: nominal speed: operating pressure (at motor inlet): operation with lubricated air possible? yes no smallest opening cross-section of connection pieces and hoses? standard steel non-corrosive aluminium plastics ceramics other: drive shaft requirements: (e. g. keyed shafts, square end, hexagonal, collet, drill chuck taper, etc.) required dimensions: W Nm rpm bar mm fixture design: mounting requirements: (bracket, flange, etc.) required dimensions: Additional components: holding brake gear box: operational brake Price range: Annual requirement: 27

28 DEPRAG SCHULZ GMBH u. CO. P.O. Box 1352, D Amberg, Germany Carl-Schulz-Platz 1, D Amberg Phone (+49) , Fax (+49) CERTIFIED AS PER DIN EN ISO 9001 DEPRAG. All rights and technical alterations reserved Fri