Circulation pumps BFP-ATEX-T3/T4

Size: px
Start display at page:

Download "Circulation pumps BFP-ATEX-T3/T4"

Transcription

1 Circulation pumps BFP-ATEX-T3/T F ATEX - range of use: to zone 1 and zone 1 T3 to zone 1 and zone 1 T Low noise emission High vol. efficiency Optimum suction Gerotor principle Resistant to contamination Page 1/ Bühler Technologies GmbH D - Ratingen, Harkortstr. 9 Tel.: + 9 () 1 / 99- Fax: + 9 () 1 / 99- Internet: fluidcontrol@buehler-technologies.com

2 Why a gerotor? Numerous applications in hydraulic and lubrication systems just require the circulation of the fluid. In such cases low noise emissions and low pressure ripples are more important than highly efficient transmission of energy. The gerotor is the ideal principle for such applications. The displacement mechanism consists of the inner and the outer rotor. The number of teeth of the inner rotor is always one less then the outer rotor. The rotation of the gerotor generates chambers of changing volumes between the inner and outer rotor. The variation of the volume follows a sinus curve with low amplitude resulting in a proportional flow with very low pressure ripples. F33X The relation between number of teeth, diameter and width of the gerotor has been chosen with the target for a very compact design featuring small physical dimensions, low weight and minimal loss in efficiency. The low differential of revolutions between the inner and outer rotor provides low vibration and long life. The internal design of the pump head reduces the loss of pressure and ensures good suction performance. Why complete pump units? Each additional component increases the physical volume of a system and results in higher space consumption and cost. Therefore the main target for the BFP-series was set to provide a compact solution. With the models BFP 5 up to the gerotor is directly driven by the motor shaft. The larger pumps BFP and are driven with a special coupling where the motor shaft is integrated. This concept results in additional benefits like good cooling and lubrication. ATEX marking Our devices are suitable for the following hazardeous areas: Zone 1 (gas) and Zone 1 (dust) as well as Zone (gas) and Zone (dust) Type of protection c = protection by constructional safety k = protection by liquid immersion Explosion group IIC (includes IIA + IIB) Temperature class T3/T Ex marking (maximum configuration) Category (for Zone 1) Type of protection Gas-temperature class Category (for Zone 1) Type of protection Gas-temperature class II GD ck IIC T3 T15 C II GD ck IIC T T C Device group Atmosphere G = Gas D = Dust Gas- Explosion group max. surface temperature in dust-loaded atmosphere Device group Atmosphere G = Gas D = Dust Gas- Explosion group max. surface temperature in dust-loaded atmosphere Page /

3 General data Pump bodyanodised and impregnated cast aluminum Gerotor sintered steel Operating fluids mineral oil according to DIN 515 Fluid temperature max. C Sealing Perbunan (NBR) on request: Viton (FPM) Ambient temperature -15 C to + C max. allowed operating pressure 15 bar Electric motors Voltage 3/ V, 5 Hz ±5% 77/ V, Hz ±5% Protection class IP 5 Design three-phase asynchronous squirrel-cage induction motor, totally enclosed fan cooled (TEFC) The motors comply with the standards EN 79-, EN 79-7, EN 11-, EN 11-1 Insulation Class F Finishing RAL All pumps are delivered with cable gland in the terminal box of the motor. Selection of pumps: Select the pump model by selecting the required motor power with respect to the viscosity of the oil used. The stated motor power refers to the maximum oil viscosity at maximum working pressure. As an option pump models BFP to BFP can be equipped with an additional internal bypass valve opening at bar. Dimensions are not affected. Installation notes: The pump head can be mounted for all models in rotating steps of to align the connections to the piping layout. Regard the offset of the connection threads to the centerline of the motor. The threads are manufactured according to ISO. The sealing surfaces are machined and suitable for soft sealing. We recommend using thread ends according to ISO Note: Regard dimensioning of the suction line. The stated nominal cross-section should not be reduced. A high noise level normally indicates too low cross-section of the suction line. Please take notice of the instructions in the manual. Type code BFP --,75kW-Atex-T3-BPx Temperature class T3/T Atex-marking BFP --,75kW-Atex-T3-BPx Motor power output Poles Volume of pump If the by-pass valve is needed the following codes have to be added: By-pass version BP x By-pass valve By-pass pressure (bar) Not for BFP and BFP Page 3/

4 Temperature class T3 Temperature class T BFP --,75kW BFP15--,75kW BFP15--1,5kW BFP --,75kW BFP15--,75kW BFP15--1,5kW 3775ATEXT ATEXT ATEXT3 3775ATEXT ATEXT ATEXT Motor power,75 kw,75 kw 1,5 kw,75 kw,75 kw 1,5 kw Max. oil viscosity 15 cst cst 15 cst cst ca. 1,7 A ca. 1,7 A ca. 3,3 A Part No. At max. working pressure Number of poles Max. current consumption ca. 3, A ca.,1 A ca.,1 A (V/5Hz) Delivery volume nominal 5, cm³/u 11,7 cm³/u 11,7 cm³/u 5, cm³/u 11,7 cm³/u 11,7 cm³/u at 5/ Hz /1 l/min 1/ l/min 1/ l/min /1 l/min 1/ l/min 1/ l/min Connection suction side G3//DN G1 1/-DN3 G1 1/-DN3 G3//DN G1 1/-DN3 G1 1/-DN3 Connection pressure side G1/-DN1 5 db(a) 59 db(a) 59 db(a) 5 db(a) 59 db(a) 59 db(a) 1, kg 1, kg 1, kg 15 kg 15 kg 1,7 kg A 9,5 9,5 1,5 1,5 1,5 19,5 B C ,5 D E F G H J K L M xø9 xø1 xø1 xø1 Suction pressure for all models temporarily up to -, bar Acoustic power acc. to ISO 37 Weight G1/-DN1 -, bar Dimensions (mm) xø1 Flow rate BFP / BFP 15 1 l/min BFP 15--,75 kw BFP --,75 kw Page / bar 1

5 Temperature class T3 BFP 3--,75kW Part No ATEXT3 Motor power,75kw Max. oil viscosity cst At max. working pressure bar Temperature class T BFP3--1,5kW 37315ATEXT3 BFP--1,5kW 3715ATEXT3 1,5 kw cst 1,5kW 7cSt BFP 3--,75kW cst BFP3--1,5kW 37315ATEXT 1,5 kw cst BFP--1,5kW 3715ATEXT 1,5kW 7cSt bar ca. 1,7 A ca. 1,7 A ca. 3,3 A, cm³/u 9/35 l/min 3, cm³/u /5 l/min 37375ATEXT,75kW Number of poles Max. current consumption ca.,1 A ca. 3, A, cm³/u 9/35 l/min, cm³/u 9/35 l/min 1 db(a) 1 db(a) db(a) 1 db(a) 1 db(a) db(a) 11, kg 1, kg 17, kg 1, kg 1, kg, kg ,5 117, B 3 37 C D E 7 F G 157 H 77 xø9 xø1 xø1 xø1 ca. 3, A (V/5Hz) Delivery volume nominal at 5/ Hz 3, cm³/u, cm³/u /5 l/min 9/35 l/min G1 1/-DN3 -, bar Connection suction side Connection pressure side Suction pressure for all models temporarily up to -, bar Acoustic power acc. to ISO 37 Weight Dimensions (mm) A J K Flow rate BFP 3/ BFP 5 l/min BFP --1,5 kw BFP 3--1,5 kw BFP 3--,75 kw Page 5/ bar 1

6 Temperature class T3 Part No. Temperature class T BFP --, kw BFP --3kW BFP --, kw BFP --3kW 37ATEXT3 373ATEXT3 37ATEXT 373ATEXT Motor power, kw 3 kw, kw 3 kw Max. oil viscosity cst cst ca.,5 A ca., A At max. working pressure Number of poles ca.,9 A Max. current consumption (V/5Hz) ca., A at 5/ Hz Connection suction side, cm³/u 5/7 l/min G1 1/-DN Connection pressure side G1 1/-DN3 Delivery volume nominal* Suction pressure -, bar for all models temporarily up to -, bar db(a) Acoustic power acc. to ISO 37 3, kg 3, kg kg 31 kg A 179 B C 11 D E 19 F 11 G 1 H J 71 3 K Weight Dimensions (mm) 1 Flow rate BFP l/min 59 BFP --3 kw BFP --, kw Page / 53 barbar

7 Temperature class T3 Part No. Temperature class T BFP --, kw BFP --3kW BFP --, kw BFP --3kW 37ATEXT3 373ATEXT3 37ATEXT 373ATEXT Motor power, kw 3 kw, kw 3 kw Max. oil viscosity cst cst ca., A at 5/ Hz Connection suction side ca.,5 A 1, cm³/u /15 l/min G1 1/-DN Connection pressure side G1 1/-DN3 At max. working pressure Number of poles Max. current consumption (V/5Hz) ca.,9 A ca., A Delivery volume nominal Suction pressure -, bar for all models temporarily up to -, bar 5 db(a) Acoustic power acc. to ISO 37, kg, kg 7,7 kg 3,7 kg A 1,5 1,5 1,5 191,5 B C 11 D E 19 F 11 G 1 H J 71 3 K Weight Dimensions (mm) Flow rate BFP l/min 9 BFP --3 kw BFP --, kw 3 Page 7/ bar

8 The series BFP is a product designed by BÜHLER company The company BÜHLER Technologies GmbH, Ratingen was founded in 9. BÜHLER s corporate philosophy is to offer products and solutions representative of the state of the art. BÜHLER also specialises in producing level and temperature measuring equipment, particularly for the fluid power industry. The products Our commitment to customers has given rise to a production program which comprises specialized products for fluid technology. Although these products were initially developed entirely as specials many of them have now become industry standards. Bühler quality Bühler has achieved accreditation from Lloyd s register to be in compliance with ISO 1 and therefore consider it our obligation to offer our customers not only excellent products, but also the best service possible. Page / we reserve the right to amend specification

Oil/air cooler BLK ATEX-3GD

Oil/air cooler BLK ATEX-3GD FluidControl Oil/air cooler BLK ATEX-3GD Drives and hydraulic aggregates are also used in explosive areas in machine construction or raw material production. In hydraulic systems oil transfers power and

More information

Off-line filter / cooler unit FGSL

Off-line filter / cooler unit FGSL Fluidcontrol Off-line filter / cooler unit FGSL Coolers are used to stabilise the operating temperature in hydraulic and lubrication systems. This can be implemented particularly cost-efficiently by integrating

More information

Off-line filter / cooler unit BKF

Off-line filter / cooler unit BKF FluidControl Off-line filter / cooler unit BKF In hydraulic systems oil transfers power and motion, and in drives it s a vital lubricant. Both as a power transfer medium and as a lubricant, oil is heated

More information

Sample gas pumps P2.x ATEX

Sample gas pumps P2.x ATEX Gas Analysis Sample gas pumps P2.x ATEX Even in explosive systems in the chemical industry, petrochemistry or biochemistry, gas analysis is key for safe operation. Many of the analysis processes used in

More information

Oil / air cooler Series BLK-DC

Oil / air cooler Series BLK-DC Oil / air cooler Series BLK-DC maintenance friendly design broad performance range compact dimensions rugged cooling matrix low noise emissions comprehensive accessoires DE 35 0002 09/2000 Bühler Technologies

More information

Off-Line Filter BNF. FluidControl

Off-Line Filter BNF. FluidControl FluidControl Off-Line Filter BNF In hydraulic systems oil transfers power and motion, and in drives it s a vital lubricant. Both as a power transfer medium and as a lubricant, oil is heated by friction

More information

Sample gas pumps P 2.3, P 2.3C, P 2.83, P 2.4, P 2.4C, P 2.84

Sample gas pumps P 2.3, P 2.3C, P 2.83, P 2.4, P 2.4C, P 2.84 Gas Analysis Sample gas pumps P 2.3, P 2.3C, P 2.83, P 2.4, P 2.4C, P 2.84 Gas analysis is key for safe and efficient system operation in the chemical industry, petrochemistry or biochemistry. Many of

More information

Oil/air cooler BLK. Fluidcontrol

Oil/air cooler BLK. Fluidcontrol Fluidcontrol Oil/air cooler BLK Drives and hydraulic aggregates are used in machine construction, raw material production, maritime and many other areas. In hydraulic systems oil transfers power and motion,

More information

Off-line filter units BNF. Installation and Operation Instructions. Original instructions. Fluidcontrol BE /2019

Off-line filter units BNF. Installation and Operation Instructions. Original instructions. Fluidcontrol BE /2019 Fluidcontrol Off-line filter units Installation and Operation Instructions Original instructions BE380002 03/2019 Bühler Technologies GmbH, Harkortstr. 29, D-40880 Ratingen Tel. +49 (0) 21 02 / 49 89-0,

More information

Feed Pumps VP / VPB / VPBM

Feed Pumps VP / VPB / VPBM Feed Pumps VP / VPB / VPBM Symbol General The feed pumps from the VP series are low-noise, single-stroke vane pumps with constant flow rate. Using a damped bell housing (PT) enables noise levels to be

More information

Oil / water cooler Series BWT

Oil / water cooler Series BWT Oil / water cooler Series BWT high exchange efficiency low water consumption equally distributed turbulent flow maintenance free little installation space required broad temperature range high fatigue

More information

SERIES R - MD MOR & GOR

SERIES R - MD MOR & GOR SERIES R - MD MOR & GOR CHARACTERISTICS OPTIONS Aluminium alloy construction Surface protection treatment (anodising, only for ATEX 2 versions) Available in monoblock execution (MOR) and with coupling

More information

Feed Pumps Direct Drive Series 1.1.

Feed Pumps Direct Drive Series 1.1. 1.1. FEED PUMP SERIES FZP AND MFZP 1. GENERAL The feed pump, type FZP, is a direct drive vane pump with constant flow rate. It is available with flanged motor (MFZP) and comes with internal pressure relief

More information

Gerotor pump, fixed displacement volume

Gerotor pump, fixed displacement volume Gerotor pump, fixed displacement volume RE 10545/12.11 1/12 Type GZ Component series 1X Maximum operating pressure 15 bar Maximum displacement 140 cm³ H7572_d Table of contents Contents age eatures 1 Ordering

More information

Oil/Air Cooler Units. Compact application with AC Motor OK-ELC Type

Oil/Air Cooler Units. Compact application with AC Motor OK-ELC Type COMPACT OIL / AIR COOLERS NEW COMPACT DESIGN WITH AC ELECTRIC FANS AND HIGH COOLING PERFORMANCE Application These coolers are designed specifically for hydraulic applications where high performance and

More information

Oil/Air Cooler Units. Compact application with AC Motor OK-ELC Type. Test procedure certified following EN 1048

Oil/Air Cooler Units. Compact application with AC Motor OK-ELC Type. Test procedure certified following EN 1048 COMPACT OIL / AIR COOLERS NEW COMPACT DESIGN WITH AC ELECTRIC FANS AND HIGH COOLING PERFORMANCE Application These coolers are designed specifically for hydraulic applications where high performance and

More information

p max (see table of performances) Q max (see table of performances) bar Maximum flow l/min see par

p max (see table of performances) Q max (see table of performances) bar Maximum flow l/min see par 41 510/112 ED EXPLOSION-PROOF VERSION SOLENOID OPERATED DIRECTIONAL CONTROL VALVES in compliance with ATEX 94/9/EC MD1K ISO 4401-03 (CETOP 03) E4P4K CETOP P05 E07P4K ISO 4401-07 (CETOP 07) E5P4K ISO 4401-08

More information

Centrifugal fan with highly efficient EC drive motor

Centrifugal fan with highly efficient EC drive motor Centrifugal fan with highly efficient EC drive motor simple and safe application and installation 2 Why HLU? 90 years of experience in the plastics processing market More than 10.000 m² production in Germany

More information

- DIMENSIONS AND WEIGHT 400 PUMP DUMPER 1X SERIES 400 PUMP DUMPER 2X SERIES 401 PUMP DUMPER 3X, 4X, 5X, 6X, 7X, 8X SERIES 402 PACKING 403

- DIMENSIONS AND WEIGHT 400 PUMP DUMPER 1X SERIES 400 PUMP DUMPER 2X SERIES 401 PUMP DUMPER 3X, 4X, 5X, 6X, 7X, 8X SERIES 402 PACKING 403 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 204 GAMMA 205 CURVE SPECIFICATIONS 206 PERFORMANCE CURVE 1X 207 PERFORMANCE CURVE 2X 208 PERFORMANCE CURVE 3X 53.7 209 PERFORMANCE CURVE

More information

- DIMENSIONS AND WEIGHT 400 PUMP DUMPER 1X SERIES 400 PUMP DUMPER 2X SERIES 401 PUMP DUMPER 3X, 4X, 5X, 6X, 7X, 8X SERIES 402 PACKING 403

- DIMENSIONS AND WEIGHT 400 PUMP DUMPER 1X SERIES 400 PUMP DUMPER 2X SERIES 401 PUMP DUMPER 3X, 4X, 5X, 6X, 7X, 8X SERIES 402 PACKING 403 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 204 GAMMA 205 CURVE SPECIFICATIONS 206 PERFORMANCE CURVE 1X 207 PERFORMANCE CURVE 2X 208 PERFORMANCE CURVE 3X 53.7 209 PERFORMANCE CURVE

More information

3D SERIES. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page

3D SERIES. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page CONTENTS Page - SPECIFICATIONS 0 SELECTION CHART 1 TYPE KEY 3 PERFORMANCE CURVE SPECIFICATIONS 4 PERFORMANCE CURVE 32-125 5 PERFORMANCE CURVE 32-6 PERFORMANCE CURVE 32-0 7 PERFORMANCE CURVE 40-125 8 PERFORMANCE

More information

HAZMAT PUMPS TUP, GUP, IN EX explosion proof up to 620 l/min, up to 2.0 bar

HAZMAT PUMPS TUP, GUP, IN EX explosion proof up to 620 l/min, up to 2.0 bar HAZMAT PUMPS TUP, UP, IN EX explosion proof up to 620 l/min, up to 2.0 bar Hazmat pumps TUP acc. to DIN 14 424, protection class EEx II 2 c IIB T3 for inflammable and non-aggressive liquids TUP 2-1 TUP

More information

Directional Control Valve Series D1VW

Directional Control Valve Series D1VW Characteristics The NG6 directional control valve series D1VW provides high functional limits up to 8 l/min in combination with a very low, energy-saving pressure drop. A wide variety of spool options

More information

Small centrifugal fans made of plastic

Small centrifugal fans made of plastic Small centrifugal fans made of plastic durable application-optimised wide range of variants 2 Small centrifugal fans made of plastic Index Small centrifugal fans made of plastic HF R 75-16 D and HF R 110-18

More information

Filter module AF Features. MAHLE Industrialfiltration is now Filtration Group. For more information, visit

Filter module AF Features. MAHLE Industrialfiltration is now Filtration Group. For more information, visit MAHLE Industrialfiltration is now Filtration Group. For more information, visit www.filtrationgroup.com Filter module AF 43 Nominal pressure 16 bar, nominal temperature 180 C; nominal width DN 80 to DN

More information

Oil/air cooler BLK. Fluidcontrol

Oil/air cooler BLK. Fluidcontrol Fluidcontrol Oil/air cooler BLK Drives and hydraulic aggregates are used in machine construction, raw material production, maritime and many other areas. In hydraulic systems oil transfers power and motion,

More information

Oil/Air Cooler Units. Standard series EL Type. Test procedure certified following EN 1048

Oil/Air Cooler Units. Standard series EL Type. Test procedure certified following EN 1048 COMPLETE OIL / AIR COOLER SYSTEM WITH AXIAL FAN FOR INDUSTRIAL APPLICATIONS. Application These high performance coolers with axial fans are suitable for hydraulic cooling applications with both return

More information

DL /116 ED SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SERIES 10 SUBPLATE MOUNTING ISO p max 320 bar Q max 125 l/min

DL /116 ED SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SERIES 10 SUBPLATE MOUNTING ISO p max 320 bar Q max 125 l/min 41 330/116 ED SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SUBPLATE MOUNTING ISO 4401-05 p max 320 bar Q max 125 l/min MOUNTING INTERFACE OPERATING PRINCIPLE ISO 4401-05-04-0-05 (CETOP 4.2-4-05-320)

More information

Asynchronous, Low Voltage, Squirrel Cage, Three Phase Electric Motors

Asynchronous, Low Voltage, Squirrel Cage, Three Phase Electric Motors Asynchronous, Low Voltage, Squirrel Cage, Three Phase Electric Motors Series R2, Frame 63 355 Introduction KHM R2 series cast iron motors are totally enclosed fan cooled, 3 phase, and squirrel cage induction

More information

DSE /117 ED DIRECTIONAL VALVE WITH PROPORTIONAL CONTROL SERIES 11 SUBPLATE MOUNTING ISO p max 350 bar Q max 40 l/min

DSE /117 ED DIRECTIONAL VALVE WITH PROPORTIONAL CONTROL SERIES 11 SUBPLATE MOUNTING ISO p max 350 bar Q max 40 l/min 83 2/117 ED DSE3 DIRECTIONAL VALVE WITH PROPORTIONAL CONTROL SUBPLATE MOUNTING ISO 41-3 p max 3 bar Q max l/min MOUNTING SURFACE OPERATING PRINCIPLE ISO 41-3-2-- (CETOP 4.2-4-3-3). 33 3.2 21. 12.7.1.7

More information

Lowara. Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733. SH Series. 60 Hz

Lowara. Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733. SH Series. 60 Hz Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733 SH Series 60 Hz SERIE SH HYDRAULIC PERFORMANCE RANGE AT 60 Hz WEB 10-2006 2 CONTENTS 5 Specifications... 6

More information

DUMPER. Data Book 50 Hz

DUMPER. Data Book 50 Hz Data Book 50 Hz CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 CURVE SPECIFICATIONS 203 1X 51-S 204 1X 51.5-S 205 2X 51.5-S 206 2X 52.2-S 207 2X 53-S 208 3X

More information

DUMPER. Data Book 50 Hz

DUMPER. Data Book 50 Hz Data Book 50 Hz CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 CURVE SPECIFICATIONS 203 1X 51-S 204 1X 51.5-S 205 2X 51.5-S 206 2X 52.2-S 207 2X 53-S 208 3X

More information

DL /118 ED SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SUBPLATE MOUNTING ISO p max 280 bar Q max 50 l/min

DL /118 ED SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SUBPLATE MOUNTING ISO p max 280 bar Q max 50 l/min 41 211/118 ED DL3 SOLENOID OPERATED DIRECTIONAL CONTROL VALVE COMPACT VERSION SUBPLATE MOUNTING ISO 4401-03 p max 280 bar Q max 50 l/min MOUNTING SURFACE OPERATING PRINCIPLE ISO 4401-03-02-0-05 (CETOP

More information

Technical data 50 & 60 Hz. Vertical centrifugal pumps Series: DPLHS

Technical data 50 & 60 Hz. Vertical centrifugal pumps Series: DPLHS Technical data 50 & 60 Hz Vertical centrifugal pumps Series: DPLHS 2 Table of Contents 1 Pump introduction 1.1 General... 4 1.2 Model key... 4 1.3 Description of the product... 4 1.4 Operation... 5 1.5

More information

PAB Atex-certified centrifugal pumps

PAB Atex-certified centrifugal pumps 1 6036 EN PAB Atex-certified centrifugal pumps Technical data Delivery rate Q max = 305 l/min Delivery head H max = 20 m Temperature range 0 C to +60 C Quality Management DIN EN ISO 9001: 2008 Environmental

More information

DUMPER. Data Book 50 Hz

DUMPER. Data Book 50 Hz Data Book 50 Hz CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 202 GAMMA 203 CURVE SPECIFICATIONS 204 1X 51-S 205 1X 51.5-S 206 2X 51.5-S 207 2X 52.2-S 208 2X 53-S 209 3X 53.7-S 210 3X

More information

Automatic metal-edge filter AF 73 G/AF 93 G

Automatic metal-edge filter AF 73 G/AF 93 G Automatic metal-edge filter AF 73 G/AF 93 G with radial scraper cleaning Connection size G2, screw-in flange DN 50 and DN 65 1 Features MAHLE automatic metal-edge filters are suitable for all applications

More information

3D SERIES. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page

3D SERIES. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page CONTENTS Page SPECIFICATIONS 0 SELECTION CHART 1 TYPE KEY 3 PERFORMANCE CURVE SPECIFICATIONS 4 MEI INDEX SPECIFICATIONS 5 PERFORMANCE CURVE 32 6 PERFORMANCE CURVE 32 7 PERFORMANCE CURVE 320 8 PERFORMANCE

More information

DSE3B /118 ED DIRECTIONAL VALVE WITH PROPORTIONAL CONTROL SERIES 10 SUBPLATE MOUNTING ISO p max 350 bar Q max 40 l/min

DSE3B /118 ED DIRECTIONAL VALVE WITH PROPORTIONAL CONTROL SERIES 10 SUBPLATE MOUNTING ISO p max 350 bar Q max 40 l/min 83 215/118 ED DSE3B DIRECTIONAL VALVE WITH PROPORTIONAL CONTROL SUBPLATE MOUNTING ISO 4401-03 p max 350 bar Q max 40 l/min MOUNTING INTERFACE OPERATING PRINCIPLE ISO 4401-03-02-0-05 (CETOP 4.2-4-03-350)

More information

Intrinsically safe solenoid valves on/off controls - ATEX or IECEX certification

Intrinsically safe solenoid valves on/off controls - ATEX or IECEX certification Table E3-/E Intrinsically safe solenoid valves on/off controls - ATEX or IECEX certification valve body valve spool intrinsically safe solenoid electrical connector manual override DHW-6/WP/6 On/off valves

More information

MINI POWER PACKS WITH SUBMERSED MOTOR AND PUMP

MINI POWER PACKS WITH SUBMERSED MOTOR AND PUMP MINI POWER PACKS WITH SUBMERSED MOTOR AND PUMP CMI Summary table Essential characteristic of the control unit compact CMI is the arrangement of the motor pump unit completely immersed in the oil inside

More information

Page - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400

Page - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE 65-250 204 PERFORMANCE CURVE 80-160 205 PERFORMANCE CURVE 80-200 206 PERFORMANCE CURVE 80-250

More information

Automatic metal-edge filters AF 72 G

Automatic metal-edge filters AF 72 G Automatic metal-edge filters AF 72 G with radial scraper cleaning Connection size G1 1/2, flange DN 40 1 Short description MAHLE automatic metal-edge filters are suitable for all applications where low

More information

INLINE Flow sensor for hazardous area II 1 G/D - II 2 D - II 3 GD - I M1

INLINE Flow sensor for hazardous area II 1 G/D - II 2 D - II 3 GD - I M1 INLINE Flow sensor for hazardous area II G/D - II D - II GD - I M Type SE0 Ex can be combined with... Flow meter with NAMUR or NPN/PNP output signal Mounting, dismounting of electronics by a Quarter-Turn

More information

MMD 4 Poles. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page

MMD 4 Poles. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE MMD4 32-250 205 PERFORMANCE CURVE MMD4 40-250 206 PERFORMANCE CURVE MMD4 50-250 207 PERFORMANCE

More information

P R O D U C T I N F O R M A T I O N. Gear pumps. Series LZ / LZM

P R O D U C T I N F O R M A T I O N. Gear pumps. Series LZ / LZM P R O D U C T I N F O R M A T I O N Gear pumps Series LZ / LZM Contents Description Description... 2 Design... 3 Application range... 4 Material and performance range... 5 Functional principle... 6 General

More information

General Specifications DRV DRV-Exm DRV-Exd

General Specifications DRV DRV-Exm DRV-Exd direct operated, 3-way pressure reducing valve Q max = 8 l/min pressure range = - 5 bar body stainless steel (optional) Description The proportional pressure reducing valve (3-way function) is used to

More information

LPCD. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page

LPCD. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 40 204 PERFORMANCE CURVE 50 205 PERFORMANCE CURVE 65 207 PERFORMANCE CURVE 80 208 PERFORMANCE

More information

OFFLINE SERIES GLOBAL STANDARD COOLER

OFFLINE SERIES GLOBAL STANDARD COOLER OFFLINE SERIES GLOBAL STANDARD COOLER OIL-TO-AIR COOLING SYSTEMS WITH AC-MOTOR AND PUMP Product information AKG-Line is a standard line of products from the market leader in high performance aluminium

More information

HERION SERIES Indirect solenoid actuated soft seal

HERION SERIES Indirect solenoid actuated soft seal HERION 9700 SERIES Indirect solenoid actuated soft seal spool valves with NAMUR interface /, 5/ - G/ For single and double acting actuators Crossover-free switching, switchover function guaranteed even

More information

IPV catalog High-pressure internal gear pumps

IPV catalog High-pressure internal gear pumps Voith Turbo IPV catalog High-pressure internal gear pumps Benefits that convince Internal gear pumps from Voith Turbo are working reliably in hundreds of thousands of machines worldwide. Sophisticated

More information

Data sheet: Wilo-Drain TP 65 F 109/22 (3~400 V)

Data sheet: Wilo-Drain TP 65 F 109/22 (3~400 V) Data sheet: Wilo-Drain TP 65 F 109/22 (3~400 V) Pump curves Wilo-Drain TP 65 F - 50 Hz - No. of poles: 2 Unit Max. delivery head H max 14.5 m Max. volume flow Q max 52.0 m 3 /h Optimal delivery head H

More information

OFFLINE SERIES GLOBAL STANDARD COOLER. p f

OFFLINE SERIES GLOBAL STANDARD COOLER. p f OFFLINE SERIES GLOBAL STANDARD COOLER Sales@SouthwestThermal.com p. 888-6-8 f. 80-484-0049 www.akgcoolers.com OIL-to-AIR COOLING SYSTEMS Product Information AKG Offline Series, based on AKG Cool-Line Series,

More information

EUGEN WOERNER GmbH & Co. KG Postfach 1661 DE Wertheim Am Eichamt 8 DE Wertheim. Pump unit GMZ-E

EUGEN WOERNER GmbH & Co. KG Postfach 1661 DE Wertheim Am Eichamt 8 DE Wertheim. Pump unit GMZ-E Pump unit GMZ-E Pump used to supply oil and grease from a barrel directly through a lid-hole or a bunghole. Technical data: Pump with bung-hole Pump with barrel lid Delivery volume per stroke: Pump element

More information

3/2 and 4/2 directional seat valves with solenoid actuation

3/2 and 4/2 directional seat valves with solenoid actuation 1/16 3/2 and 4/2 directional seat valves with solenoid actuation RE 22049-XN-B2/08.12 Replaces: 07.10 Type M-.SED 6...XN... Size 6 Component series 1X Maximum operating pressure 350 bar Maximum flow 25

More information

HEAT EXCHANGERS AIR/OIL TYPE LAC. - ATEX Version. Approved for applications where there may be an explosive environment above ground.

HEAT EXCHANGERS AIR/OIL TYPE LAC. - ATEX Version. Approved for applications where there may be an explosive environment above ground. Heat exchangers Air/Oil LAC - LAC with AC Motor for Industrial Use - Maximum cooling capacity 300 kw Heat exchangers Air/Oil LAC-X - ATEX Version. Approved for applications where there may be an explosive

More information

97100 NAMUR. Technical data

97100 NAMUR. Technical data 9700 NAMUR /2-, /2- and / Directional control valves Actuation: electromagnetic Indirectly controlled soft seal spool valves Port size: G /4, /4 NPT NAMUR Interface For single and double operated actuators

More information

Screwpump. Series D GB. General Description. Model Code D 4

Screwpump. Series D GB. General Description. Model Code D 4 Screwpump Series D4 A Member of the COLFAX PUMP GROUP Handling of hydraulic oils, seal oils and fuel oils Max. working pressure: 160 bar Flow range: 10-850 I/min General Description Positive constant displacement,

More information

Page - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400

Page - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 203 LPC4 32 205 LPC4 40 206 LPC4 50 211 LPC4 65 215 LPC4 80 219 LPC4 100 222 LPC4 125 225 LPC4 150 226 - CONSTRUCTIONS

More information

A-L O C COOLING SYSTEM OLAER COOLERS. Olaer A-LOC with integrated circulation pump for industrial hydraulic systems

A-L O C COOLING SYSTEM OLAER COOLERS. Olaer A-LOC with integrated circulation pump for industrial hydraulic systems OLAER A-L O C COOLERS COOLING SYSTEM Olaer A-LOC with integrated circulation pump for Olaer A-LOC with integrated circulation pump for industrial hydraulic systems R OLAER A-LOC FOR OPTIMUM EFFICIENCY

More information

IPVP High-pressure Internal Gear Pumps for Variable Speed Drives

IPVP High-pressure Internal Gear Pumps for Variable Speed Drives IPVP High-pressure Internal Gear Pumps for Variable Speed Drives Design and Function 7 6 5 9 2 5 6 7 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing

More information

Volute Casing Centrifugal Pumps in In-line Design with Magnetic Drive. Series CNI-M

Volute Casing Centrifugal Pumps in In-line Design with Magnetic Drive. Series CNI-M Volute Casing Centrifugal Pumps in In-line Design with Magnetic Drive Series CNI-M Usage For pumping toxic, volatile, explosive or other fluids harmful to the environment which call for service of hermetically

More information

Automatic filter AF 113 G

Automatic filter AF 113 G Automatic filter AF 113 G Cast design with internal pressure cleaning and integrated cyclone effect Connection sizes: G2, screw in flange DN 50 and DN 65 1 Short description MAHLE automatic backflush filters

More information

RE 91808/ AA4VSE Plug-in dual displacement motor. High pressure range. Series 10 Axial piston swashplate design, SAE model

RE 91808/ AA4VSE Plug-in dual displacement motor. High pressure range. Series 10 Axial piston swashplate design, SAE model AA4VSE Plug-in dual displacement motor Series Axial piston swashplate design, SAE model RE 91808/09.90 RE 91808/09.90 Brueninghaus Hydromatik Size 250 Nominal pressure 350 bar Peak pressure 400 bar High

More information

Automatic filter AF 172 G

Automatic filter AF 172 G Automatic filter AF 172 G with external pressure cleaning and integrated cyclone effect Connection sizes: DN 40/G1 1/2, cast design 1. Short description MAHLE automatic backflush filters are suitable for

More information

ANKERSMID Temperature controller ATC 510/520/525 for wall-mounting. Application

ANKERSMID Temperature controller ATC 510/520/525 for wall-mounting. Application 2-3.1 ATC 510/520/525 for wall-mounting Application The ATC 510/5205/525 is a modern microprocessor-based (PID) control device featuring easy handling and a digital display. The clear design of the operator

More information

franklinwater.com 50 Hz VR SERIES Vertical Multi-Stage Pumps

franklinwater.com 50 Hz VR SERIES Vertical Multi-Stage Pumps franklinwater.com 5 Hz VR SERIES Vertical Multi-Stage Pumps 5 HZ VR SERIES VERTICAL MULTI-STAGE PUMPS Features 2 Applications 2 Pump Specifications Counter-Flange Kits Motor Specifications 4 Ordering

More information

Explosion-protected surface-mounting Thermostat ATH-Ex Series

Explosion-protected surface-mounting Thermostat ATH-Ex Series JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, 36039 Fulda, Germany Postal address: 36035 Fulda, Germany Phone: +49 661 6003-0 Fax: +49 661 6003-607 e-mail: mail@jumo.net Internet: www.jumo.net

More information

Lowara. Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733. SH Series. 50 Hz

Lowara. Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733. SH Series. 50 Hz Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733 SH Series 50 Hz SERIE SH OPERATING CHARACTERISTICS AT 50 Hz PRINT 05-2007 2 CONTENTS 5 Specifications......................................................................

More information

Automatic filter AF 173 G

Automatic filter AF 173 G Automatic filter AF 7 G with external pressure cleaning and integrated cyclone effect Connection sizes: G, screw-in flange DN 0 and DN, cast design Short description MAHLE automatic backflush filters are

More information

Oil/Air Cooler Units. Mobile series with DC motor OK-ELD Type. Test procedure certified following EN 1048

Oil/Air Cooler Units. Mobile series with DC motor OK-ELD Type. Test procedure certified following EN 1048 MOBILE OIL / AIR COOLERS NEW COMPACT DESIGN WITH DC ELECTRIC FANS AND HIGH COOLING PERFORMANCE Application These coolers are designed specifically for mobile hydraulic applications where high performance

More information

Volute Casing Centrifugal Pumps in High Temperature Design with Magnetic Drive. Series CNH-ML

Volute Casing Centrifugal Pumps in High Temperature Design with Magnetic Drive. Series CNH-ML Volute Casing Centrifugal Pumps in High Temperature Design with Magnetic Drive Series CNH-ML Usage For pumping toxic, volatile, explosive or other fluids harmful to the environment which call for service

More information

Data sheet: Wilo-Drain TP 65 F 91/11 (1~230 V)

Data sheet: Wilo-Drain TP 65 F 91/11 (1~230 V) Data sheet: Wilo-Drain TP 65 F 91/11 (1~230 V) Pump curves Wilo-Drain TP 65 F - 50 Hz - 2900 rpm Unit Max. delivery head H max 9.5 m Max. volume flow Q max 36 m 3 /h Optimal delivery head H opt 6.0 m Optimum

More information

Page - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING TECHNICAL DATA 500

Page - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING TECHNICAL DATA 500 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE BEST 2 203 PERFORMANCE CURVE BEST 3 203 PERFORMANCE CURVE BEST 4 203 PERFORMANCE CURVE BEST

More information

FNA 008 FNA 016 Operating pressure up to 4 bar / 58 psi Nominal flow rate up to 16 l/min / 4.2 gpm

FNA 008 FNA 016 Operating pressure up to 4 bar / 58 psi Nominal flow rate up to 16 l/min / 4.2 gpm Off-line Filter Units FNA 008 FNA 016 Operating pressure up to 4 bar / 58 psi Nominal flow rate up to 16 l/min / 4.2 gpm Description Application In the by-pass flow of hydraulic and lubrication systems.

More information

MMD. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page

MMD. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 202 PERFORMANCE CURVE 65-250 204 PERFORMANCE CURVE 80-160 205 PERFORMANCE CURVE 80-200 206 PERFORMANCE CURVE 80-250

More information

Feed Pumps Direct Drive Series 1.1.

Feed Pumps Direct Drive Series 1.1. 1.1. FEED PUMP SERIES FZP AND MFZP 1. GENERAL The feed pump, type FZP, is a direct drive vane pump with constant flow rate. It is available with flanged motor (MFZP) and comes with internal pressure relief

More information

VED*HL-*-KD2 - HAZARDOUS LOCATION, PROPORTIONAL, DIRECT & PILOT OPERATED VALVES

VED*HL-*-KD2 - HAZARDOUS LOCATION, PROPORTIONAL, DIRECT & PILOT OPERATED VALVES CONTINENTAL HYDRAULICS VED*HL-*-KD2 HAZARDOUS LOCATION, PROPORTIONAL, DIRECT & PILOT OPERATED VALVES (IN COMPLIANCE WITH ATEX 94/4/EC) 5505 WEST 123RD STREET SAVAGE, MN 55378-1299 / PH: 952.895.6400 /

More information

Air Cooler Industry AC-LN 8-14 / ACA-LN 8-11 / ACAF-LN 8-11

Air Cooler Industry AC-LN 8-14 / ACA-LN 8-11 / ACAF-LN 8-11 Air Cooler Industry AC-LN 8-14 / ACA-LN 8-11 / ACAF-LN 8-11 Symbol General The AC-LN 8-14 air cooler series can be used in all areas where either oil or water-glycol is to be cooled with air. The coolers

More information

Pilot Operated Pressure Relief Valve Series R5V (Denison)

Pilot Operated Pressure Relief Valve Series R5V (Denison) Characteristics Pilot operated pressure relief valves series R5V have a similar design to the subplate mounted R4V series. The SAE flanges allow to mount the valves directly on the outlet flanges of pumps

More information

Cooling Systems CC Series TT rail 20/30lpm

Cooling Systems CC Series TT rail 20/30lpm CC Series 20/30lpm General Data And Details The oil / air coolers of our CC series are autonomous cooling systems with an integrated circulation pump. They work as a separate cooling unit or as a ilter

More information

3D SERIES. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page

3D SERIES. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page CONTENTS Page SPECIFICATIONS 0 PERFORMANCE RANGE and SELECTION CHART 1 TYPE KEY 3 PERFORMANCE CURVE SPECIFICATIONS 4 MEI INDEX SPECIFICATIONS 5 PERFORMANCE CURVE 32 6 PERFORMANCE CURVE 32 7 PERFORMANCE

More information

Operating Instructions for Float Flow Meter / Monitor. Model: SWK

Operating Instructions for Float Flow Meter / Monitor. Model: SWK Operating Instructions for Float Flow Meter / Monitor Model: SWK 1. Contents 1. Contents... 2 2. Note... 3 3. Instrument Inspection... 3 4. Regulation Use... 4 5. Operating Principle... 4 6. Use in Hazardous

More information

Contents. Identification

Contents. Identification Contents Identification Type key Product data Introduction Applications Features and benefits Performance range pole pole Construction Sectional drawing Construction features Test pressure Operating conditions

More information

Automatic filter AF 112 G

Automatic filter AF 112 G Automatic filter AF 112 G Cast design with internal pressure cleaning and integrated cyclone effect Connection size: flange DN 40 or G1 1/2 1 Short description MAHLE automatic backflush filters are suitable

More information

LPC. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page

LPC. EBARA PUMPS EUROPE S.p.A. CENTRIFUGAL PUMPS. Page CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY AND CURVE SPECIFICATIONS 203 32 205 40 206 50 210 65 213 80 216 100 218 - CONSTRUCTIONS 300 SECTIONAL VIEW 300 MECHANICAL SEAL 302 - DIMENSIONS

More information

ARBO. Pompen en Filters b.v.

ARBO. Pompen en Filters b.v. ARBO Pompen en Filters b.v. Product group 1.1 Chemical pumps SealPro Applications For all transport or circulation duties of corrosive liquids, even high viscosity, with maximum efficiency. This series

More information

Automatic metal-edge filter AF 71 G

Automatic metal-edge filter AF 71 G Automatic metal-edge filter AF 71 G with radial scraper cleaning Connection size G1 1 Features MAHLE automatic metal-edge filters are suitable for all applications where low or high-viscosity liquids or

More information

Oil/Air Cooler Units. Mobile application and Hydraulic motor OK ELH Type. Test procedure certified following EN 1048

Oil/Air Cooler Units. Mobile application and Hydraulic motor OK ELH Type. Test procedure certified following EN 1048 MOBILE OIL / AIR COOLERS NEW COMPACT DESIGN WITH HYDRAULIC MOTOR AND HIGH COOLING PERFORMANCE Application These coolers are designed specifically for mobile hydraulic applications where high performance

More information

- CONSTRUCTIONS 300 SECTIONAL VIEW 300 SECTIONAL VIEW TABLE 301 MECHANICAL SEAL 302 FITTINGS DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING 401

- CONSTRUCTIONS 300 SECTIONAL VIEW 300 SECTIONAL VIEW TABLE 301 MECHANICAL SEAL 302 FITTINGS DIMENSIONS AND WEIGHT 400 PUMP 400 PACKING 401 CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 SELECTION CHART TABLE 202 TYPE KEY AND CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 25/08 204 PERFORMANCE CURVE 25/15 205 PERFORMANCE CURVE 25/25 206

More information

Variable Vane Pump, Direct Controlled PV7...A Series 1X / 2X

Variable Vane Pump, Direct Controlled PV7...A Series 1X / 2X Variable Vane Pump, Direct Controlled PV7...A Series 1X / X RE 1 Issue: 1.13 Replaces: 8.8 Sizes 1 to Maximum pressure 1 bar Displacement volume 1 to cm 3 Features Very short control times Low noise Mounting

More information

Side channel pumps PN 16 SOH - SOHB - SOHM. Self-priming centrifugal pumps. Technical description

Side channel pumps PN 16 SOH - SOHB - SOHM. Self-priming centrifugal pumps. Technical description Side channel pumps PN 16 Self-priming centrifugal pumps SOH - SOHB - SOHM Technical description ATEX certified The SOH side channel pump models are available in a variety of designs. Design base plate

More information

GMP-Type. Key Features: Integrated Motor-Pump Units

GMP-Type. Key Features: Integrated Motor-Pump Units Integrated Motor-Pump Units GMP-Type Key Features: Direct coupling between motor and pump Rotation: Right (viewed from shaft end) Electric motor mounting type: special B3-B14 (IEC 34-7) Rated Voltage:

More information

Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 202 CURVE SPECIFICATIONS 203 PERFORMANCE CURVE RIGHT PERFORMANCE CURVE RIGHT

Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 202 CURVE SPECIFICATIONS 203 PERFORMANCE CURVE RIGHT PERFORMANCE CURVE RIGHT CONTENTS Page - SPECIFICATIONS 200 SELECTION CHART 201 TYPE KEY 202 CURVE SPECIFICATIONS 203 PERFORMANCE CURVE 75 204 PERFORMANCE CURVE 100 205 - CONSTRUCTIONS 300 SECTIONAL VIEW 300 BEARINGS 301 MECHANICAL

More information

Magnetic-inductive flow meter for hazardous areas

Magnetic-inductive flow meter for hazardous areas Magnetic-inductive flow meter for hazardous areas Technical Datasheet EPX / UMF3 high accuracy: 0.3 % of actual maintenance-free no pressure drop numerous lining materials numerous electrode materials

More information

4/3, 4/2 proportional directional valves solenoid operated (for open loop control)

4/3, 4/2 proportional directional valves solenoid operated (for open loop control) /, / proportional directional valves solenoid operated (for open loop control) RE -/7. Replaces: RE7/.7 / Type L (LCP) Size Series Maximum operating pressure bar [ psi] Nominal flow rated l/min [.7 gpm]

More information

Coolers. OK Series. Air Cooled Oil Coolers Hydraulic Symbol OK 1-11 OKF Cooling Systems Catalog. Applications

Coolers. OK Series. Air Cooled Oil Coolers Hydraulic Symbol OK 1-11 OKF Cooling Systems Catalog. Applications OK Series Air Cooled Oil Coolers Hydraulic Symbol OK 1-11 OKF 3-11 OKA 4-6 OKAF 4-6 OKA 8-11 OKAF 8-11 Description The OK Series cooler design uses a axial fan assembly which draws air through the cooler.

More information

IPVS High-pressure Internal Gear Pumps Technical Data Sheet

IPVS High-pressure Internal Gear Pumps Technical Data Sheet IPVS High-pressure Internal Gear Pumps Technical Data Sheet Functional Drawing 5 9 2 8 2 9 4a 4b 3 Pinion shaft 2 Internal gear 3 Filler pin 4a Filler segment carrier 4b Filler sealing segment 5 Axial

More information

Hermetical Standard Chemical Pump of PTFE / PFA with permanent magnet synchronous motor ISO 2858 / DIN EN 22858

Hermetical Standard Chemical Pump of PTFE / PFA with permanent magnet synchronous motor ISO 2858 / DIN EN 22858 Hermetical Standard Chemical Pump of PTFE / PFA with permanent magnet synchronous motor ISO 2858 / DIN EN 22858 Hermetical Standard Chemical Pump of PTFE / PFA with permanent magnet synchronous motor ISO

More information