The airplanes that follow that have incorporated SB (or latest revision) GARMIN G1000 GPS/WAAS Installation:

Size: px
Start display at page:

Download "The airplanes that follow that have incorporated SB (or latest revision) GARMIN G1000 GPS/WAAS Installation:"

Transcription

1 Single Engine Service Bulletin January 18, 2011 TITLE GARMIN G1000 SYSTEM SOFTWARE UPGRADE TO FOR AIRPLANES EQUIPPED WITH NAV III AND WAAS EFFECTIVITY Group A airplanes The airplanes that follow that are equipped with the Garmin G1000 Nav III Avionics Option and the Wide Area Augmentation System (WAAS): Model Serial Numbers 172R thru S 172S10432 thru 172S T thru T182T T thru T H thru T206H T thru T Group B airplanes The airplanes that follow that have incorporated SB (or latest revision) GARMIN G1000 GPS/WAAS Installation: Model Serial Numbers 172R thru S 172S9810 thru 172S T , thru , thru T182T T thru T , T thru T H thru , thru T206H T thru T , T thru T Page 1 of 19 To obtain satisfactory results, procedures specified in this publication must be accomplished in accordance with accepted methods and prevailing government regulations. Cessna Aircraft Company cannot be responsible for the quality of work performed in accomplishing the requirements of this publication. Cessna Aircraft Company, Customer Service, P.O. Box 7706, Wichita, Kansas 67277, U.S.A. (316) , Facsimile (316) COPYRIGHT 2011

2 REASON This version software Service Bulletin provides an upgrade that includes the following changes: TAWS-B Alerting If installed, implemented terrain clearance and destination airport algorithm changes to reduce nuisance alerts New XM Weather Product, Aviator Pro If installed, implemented display support for AIREP, PIREP, Turbulence, Icing Potential, and Super-Cooled Liquid Droplets Weather Map Orientation Enhanced to make orientation pilot selectable instead of always "north-up" Temporary Flight Restrictions (TFR) Enhanced depiction by combining overlapping TFR circles into a single-shape TFR Course Tracking and Intercept Logic Implemented navigation system changes to improve course intercept and navigation Flight Plan Sequencing Enhanced so that manual activation of a procedure turn will not result in a suspend-state after completing the turn GFC-700 Roll Steering Updated calculations to eliminate the possibility of a roll steering over-correction when engaging the GFC-700 Autopilot Dead Reckoning Mode Added option to allow GPS course and roll steering data to be valid for up to 20 minutes after entering Dead Reckoning (DR) mode Minimum Altitude Alerts Modified so that a previously entered value is cleared when an approach is added to or deleted from the active flight plan Flight Plan Import/Export Provides capability to import and export flight plans between an SD card and the GDU flight plan memory NAV III Engine Gauges Enhanced appearance of the engine gauges to Garmin s 3D EIS Inset Maps Corrected inset map depictions so that they are always synchronized on the PFD and MFD Flight Path Marker (FPM) If Synthetic Vision is installed, the marker was modified to render behind the aircraft symbol and flight director command bars Default Waypoint Storage Duration Updated to allow the pilot to create new user-defined waypoints as either persistent or temporary and to set the defaults NAV III System Configuration Bar END (endurance), FOB (fuel on board), and FOD (fuel over destination) options are now displayed on the MFD status bar Resolution for Garmin Service Advisory No. 0904A If Synthetic Vision is installed, Pathways is now enabled Fixed Content Data Logging Provides capability of logging flight data to a comma-separated-value (CSV) file on an SD card in the upper MFD slot GTS800 TAS System Input/Output Communication If installed via field approval, allows input/output communication on RS-232 and ARINC-429 interfaces Resolution for Garmin Service Advisory No Change implemented to prevent the possibility of flagging primary flight data, COM frequency, and EIS information while all stored flight plans or user waypoints are being deleted Resolution for Garmin Service Advisory No Change implemented to allow an LPV approach to be selected at airports with 3-character identifiers Multiple Waypoint Instances Modified the Flight Plan List so that any instance of a waypoint that appears multiple times can be selected, not just the first AOPA Airport Directory Information Support added for display on the "WPT-Airport Information" page. Field aircraft will need to purchase the AOPA directory via Page 2 January 18, 2011

3 Auto Zoom Range On moving map enhanced to show active leg instead of the entire leg that is ahead of the aircraft GDU 1044B -10 Display Hardware Support Implemented software to support hardware that allows potential for external video inputs Approach Loading Cursor Operation When loading an approach, the cursor will no longer skip the "minimums" field after selecting a transition that prompts for whether to fly the course reversal Display of Groundspeed in DR Mode When DR mode is active, groundspeed is now displayed in yellow on the PFD MFD Page Navigation Updated the MFD selection window to show the Page Group and Page Title for selection. DESCRIPTION This Service Bulletin provides parts and instructions to upgrade the Garmin G1000 software to version COMPLIANCE Recommended: Should be accomplished within the next 100 hours of operation or 12 months, whichever occurs first. NOTE: For airplanes affected by Cessna Service Bulletin SB Revision 1 (Garmin G1000 System Software Upgrade to Version ). If not already accomplished, SB Revision 1 must be accomplished before compliance with this Service Bulletin. NOTE: For airplanes affected by Cessna Service Bulletin SB (Garmin G1000 System Software Upgrade to for Airplanes Equipped with NAV III and GFC 700 AFCS Autopilot). If not already accomplished, SB must be accomplished before compliance with this Service Bulletin. NOTE: Existing Garmin software backup CDs shall be destroyed and discarded to eliminate the possibility of loading the incorrect software at a later date. APPROVAL FAA approval has been obtained on technical data in this publication that affects airplane type design. MANPOWER 3.5 man-hours to load the software upgrade If necessary, 0.3 man-hour to do the applicable configuration upload for airplanes equipped with the Garmin G1000 Terrain Awareness System (TAWS-B) If necessary, 0.3 man-hour to do the applicable configuration upload for airplanes equipped with the Garmin G1000 Chartview System If necessary, 0.3 man-hour to do the applicable configuration upload for airplanes equipped with Garmin G1000 Synthetic Vision Technology (SVT) If necessary, 0.3 man-hour to do the applicable configuration upload for airplanes equipped with Garmin G1000SearchandRescue If necessary, 0.3 man-hour to do the Standby Battery Ammeter Battery Calibration Procedure January 18, 2011 Page 3

4 REFERENCES Model 172 Series 1996 and On Maintenance Manual Model 182/T182T Series 1997 and On Maintenance Manual Model 206/T206 Series 1998 and On Maintenance Manual Garmin G1000 Cockpit Reference Guide for Cessna NAV III, Part Number Rev. A. The following documents can be viewed by Cessna Service Stations by going to Garmin G1000 System Installation Manual, Part Number , Revision H (or latest revision) Garmin GDU 1040 Installation Manual, Part Number , Revision S (or latest revision) Garmin GMA 1347 Installation Manual, Part Number , Revision E (or latest revision) Garmin GIA 63 Installation Manual, Part Number , Revision S (or latest revision) Garmin GRS 77/GMU 44 Installation Manual, Part Number , Revision L (or latest revision) Garmin GDC 74A Installation Manual, Part Number , Revision F (or latest revision) Garmin GEA 71 Installation Manual, Part Number , Revision G (or latest revision) Garmin GTX 33 Installation Manual, Part Number , Revision J (or latest revision) Garmin G1000 NAV III Line Maintenance Manual, Part Number , Revision P (or latest revision) NOTE: Make sure all publications used are complete and current. Refer to NOTE: This information shall be considered an amendment to the Cessna Manufacturer's Service/Maintenance Manual and should be accomplished within the specified time requirement. OTHER PUBLICATIONS AFFECTED Model 172R & Model 172S Illustrated Parts Catalog Model 182S/182T/T182T Illustrated Parts Catalog Model 206H & Model T206H Illustrated Parts Catalog NOTE: Make sure all publications used are complete and current. Refer to Page 4 January 18, 2011

5 MATERIAL PRICE AND AVAILABILITY The following parts are available from Cessna Service Parts and Programs through a Cessna Single Engine Authorized Service Facility: NOTE: Garmin G1000 Pilot's Guide for Cessna NAV III is optional. Part Number Description Qty/Airplane Price REVA Garmin G1000 Integrated Flight Deck Cockpit Reference Guide for Cessna NAV III Models 172R/172S, 182T/T182T and 206H/T206H 1 $ REVA Garmin G1000 Pilot s Guide for Cessna NAVIII 1 $ ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE January 18, 2011 Page 5

6 CREDIT INFORMATION For airplanes out of warranty: Applicable software CD parts credit will be provided to load the software upgrade. For airplanes in warranty: Applicable Cockpit Reference Guide (CRG) and software CD parts credit and a labor allowance credit of 3.5 man-hours per airplane will be provided to load the software upgrade. for airplanes equipped with the Garmin G1000 Terrain Awareness System (TAWS-B). for airplanes equipped with the Garmin G1000 Chartview System. for airplanes equipped with Garmin G1000 Synthetic Vision Technology (SVT). for airplanes equipped with Garmin G1000 Search and Rescue. If necessary, a labor allowance credit of 0.3 man-hour will be provided to do the Standby Battery Ammeter Battery Calibration Procedure. For airplanes with SVT previously installed (in or out of warranty): Applicable CRG and software CD parts credit and a labor allowance credit of 3.5 man-hours per airplane will be provided to load the software upgrade. Only Authorized Service Facilities providing proof of SVT installation may submit a Warranty Claim to accomplish this Service Bulletin. for airplanes equipped with the Garmin G1000 Terrain Awareness System (TAWS-B). for airplanes equipped with the Garmin G1000 Chartview System. for airplanes equipped with Garmin G1000 Synthetic Vision Technology (SVT). for airplanes equipped with Garmin G1000 Search and Rescue. If necessary, a labor allowance credit of 0.3 man-hour will be provided to do the Standby Battery Ammeter Battery Calibration Procedure. NOTE: Proof of SVT purchase is a logbook entry or a purchasing receipt. Freight will be credited at the most economical method unless pre-approved by Cessna. For pre-approval contact Cessna Service Parts and Programs Warranty Administration at Telephone: , Fax: or cpd2claims@cessna.textron.com. To receive credit, the work must be completed and a Warranty Claim submitted by a Cessna Single Engine Authorized Service Facility within 30 calendar days of Service Bulletin compliance before the credit expiration dates shown below. Domestic... January18,2012 International... January18,2012 Special Note to Service Stations: When you complete the Warranty Claim, the labor allowance claimed shall be itemized for each above action completed. Page 6 January 18, 2011

7 ACCOMPLISHMENT INSTRUCTIONS WEIGHT AND BALANCE INFORMATION Negligible Material Information To complete this Service Bulletin, use the parts below as applicable: NEW P/N QUANTITY DESCRIPTION OLD P/N DISPOSITION NAVIIIGSW Model 172R Software CD NAVIIIGSW Model 172S Software CD NAVIIIGSW Model 182T Software CD NAVIIIGSW Model T182T Software CD NAVIIIGSW Model 206H Software CD NAVIIIGSW Model T206H Software CD REVA 1 Garmin G1000 Integrated Flight Deck Cockpit Reference Guide for Cessna NAV III Models 172R/172S, 182T/T182T and 206H/T206H General Information Instructions 172RGSW00-08 and prior revisions 172SGSW00-08 and prior revisions 182TGSW00-11 and prior revisions T182TGSW00-10 and prior revisions 206HGSW00-11 and prior revisions T206HGSW00-10 and prior revisions and prior revisions Destroy and Discard Destroy and Discard Destroy and Discard Destroy and Discard Destroy and Discard Destroy and Discard Remove NOTE 1: This software update only supports NAV III installations that are WAAS airplanes. If the aircraft is not a WAAS-equipped aircraft do not perform this software update NOTE 2: If the system software or configuration fails to upload correctly during accomplishment of this Service Bulletin, do the upload again. Do not try to upload more than five times. Ifthe system does not upload after the fifth attempt, contact Cessna Aircraft Customer Service, Telephone or Fax Do not cancel a software or configuration upload that is in progress. Let the system either successfully load or fail. NOTE 3: If the alert chime comes on at any time during the accomplishment of this Service Bulletin, you can go to the Alert Configuration page in the GDU page group, push the soft key directly below the ACK, and this should make the chime stop. 1. Do the software and paper documentation: A. Remove, destroy, and discard the old Cessna NAV III Installation Software CD from the sleeve in the Pilot's Operating Handbook (POH) to eliminate the possibility of reloading the incorrect software at a later date, and get the new Cessna NAV III Installation Software CD to load the new software. January 18, 2011 Page 7

8 B. Remove the old Garmin G1000 Cockpit Reference Guide for Cessna NAV III and replace it with the Garmin G1000 Cockpit Reference Guide for Cessna NAV III, Part Number C. The Garmin G1000 Cockpit Reference Guide for Cessna NAV III, Part Number and the Garmin NAV III Installation Software CD may be ordered through Cessna Service Parts and Programs. You must use the new CD when you do the software upgrade on the airplane. When not in use, the CD should be stored in the Pilot's Operating Handbook sleeve for the NAV III Garmin Software. 2. Make the 006-B Software SD Loader Card as follows: A. Use the new Cessna NAV III Installation software CD shown in TABLE 1 and update the SD Card for the correct model airplane: TABLE 1 Installation Software CD and Garmin System Software (G1000) Part Number File Version 006-B B. Right mouse click on the START button in the lower left corner of the computer screen and click on EXPLORE. C. Find the CD drive with the CD in it on your computer and double click it to open the CD file. D. Double click on the file labeled 006-B _OA.exe. E. When the window opens, click the SETUP button F. Install a blank SD Card into the SD card reader and click the NEXT button. NOTE: SanDisk is the SD card brand that is recommended by Garmin for use in their G1000 system. G. The next window will ask for your SD card reader location. Select the location of the SD card reader and then click the NEXT button. H. Click the NEXT button when the window opens. NOTE: If there is information on the SD card, it will be erased by the Software Application Builder. I. The software will begin to transfer from the CD to the SD Card. J. When the data has transferred to the SD card, click the FINISH button. K. Remove the SD card from the SD card reader and identify the SD card as 006-B L. Remove the CD from the computer and install it in the Nav III/Garmin Software sleeve in the Pilot s Operating Handbook (POH). 3. Turn on the G1000 in configuration mode to verify existing options. A. (Refer to TABLES 2, 3, and 4.) Record which options are installed for later reference. If you do not know which options are installed on your airplane, use TABLE 5 to make a list of the installed options before you go to Step 6. This list is necessary to do the correct software upload and configuration. Record in TABLE 5 all installations and configuration options necessary for the airplane. NOTE: To stop the alert chime in configuration mode, on the Alert Configuration page in the GDU page group, push the soft key that is below ACK. Page 8 January 18, 2011

9 TABLE 2- Model 172R and 172S. 172R/172S AIRPLANE MODEL CONFIGURATION FILE SELECTIONS - PULL-DOWN MENU Cessna 172R B Full Configuration (WAAS) or Cessna 172S B Full Configuration (WAAS) NOTE: All GFC 700-equipped 172R/172S airplanes are WAAS airplanes. Cessna 172R - GFC 700 Installation Option (if applicable) or Cessna 172S - GFC 700 Installation Option (if applicable) NOTE: Factory Kits FK , FK172S604, FK E, FK172S604E, FK F, FK271S604F, FK G, and FK172S604G are not equipped with the GFC 700 option. All other 172S and 172R NAV III 2008 and on airplanes are equipped with the GFC 700. Cessna NAV III CO Guardian Installation Option (if applicable) NOTE: All NAV III 2006 and on Model Year airplanes have the CO Guardian installed. Cessna NAV III CAN BUS FUEL LEVEL SENSORS (if applicable) NOTE: All NAV III 2008 and on Model Year airplanes have the CAN BUS FUEL LEVEL SENSORS installed. Cessna NAV III INITIALIZE FUEL CAL DATA (only for CAN Bus sensors before fuel cal) NOTE: Only use if CAN Bus fuel sensors are installed and you do a full fuel calibration for the airplane. Do not select this option unless a fuel calibration is necessary. Loss of fuel calibration data will result, and you will have to do a full fuel calibration. Cessna NAV III GDL90 Installation Option (if applicable) NOTE: The GDL90 is not the same equipment as the GDL69. Cessna NAV III KAP 140 Installation Option (if applicable) NOTE: Use only if a Honeywell KAP 140 AFCS is installed. A KC140 controller is installed in the instrument panel. All 2008 and later Models only installed the Garmin GFC 700 AFCS autopilot. Cessna NAV III KN 63 DME Installation Option (if applicable) NOTE: All airplanes equipped with the Cessna NAV III KN 63 DME installation option have a DME antenna installed on the bottom of the fuselage below the cabin. Cessna NAV III KR 87 ADF Installation Option (if applicable) NOTE: Airplanes equipped with the NAV III KR 87 ADF installation option have a receiver installed on the instrument panel. Cessna NAV III BP 2007 Comant CI Antenna Configuration NOTE: For WAAS equipped airplanes without a stand alone XM Antenna (CI ) Cessna NAV III (Pre 2007 Model Year Airplanes) Comant CI Antenna Configuration NOTE: All Pre 2007 Model Year Airplanes not equipped with WAAS are equipped with the Comant CI antenna. Cessna NAV III Disable SVT Pathways Option (if desired) NOTE: Most installations will not use this option. January 18, 2011 Page 9

10 TABLE 3- Model 182T and T182T 182T/T182T AIRPLANE MODEL CONFIGURATION FILE SELECTIONS - PULL-DOWN MENU Cessna 182T B Full Configuration (WAAS) or Cessna T182T B Full Configuration (WAAS) NOTE: All GFC 700 equipped 182T/T182T airplanes are WAAS airplanes. Cessna 182T GFC 700 Installation Option (if applicable) or Cessna T182T GFC 700 Installation Option (if applicable) as applicable NOTE: All 182T and T182T NAV III 2007 and on airplanes are equipped with the GFC 700. Cessna NAV III CO Guardian Installation Option (if applicable) NOTE: All NAV III 2006 and on Model Year airplanes have the CO Guardian installed. Cessna NAV III CAN BUS FUEL LEVEL SENSORS (if applicable) NOTE: All NAV III 2008 and on Model Year airplanes have the CAN BUS FUEL LEVEL SENSORS installed. Cessna NAV III INITIALIZE FUEL CAL DATA (only for CAN Bus sensors before fuel cal) NOTE: Only use if CAN Bus fuel sensors are installed and a full fuel calibration must be performed on the aircraft. Do not select this option unless a fuel calibration is required, otherwise loss of fuel calibration data will result and a full fuel calibration must be performed. Cessna NAV III KTA 870 TAS Installation Option (if applicable) NOTE: All airplanes equipped with the Cessna NAV III KTA 870 TAS have a TAS circuit breaker installed on the circuit breaker panel. NOTE: All airplanes equipped with the Cessna NAV III KTA 870 TAS have a directional TAS antenna installed on the top of the airplane and a TAS antenna installed on the bottom of the airplane. Cessna NAV III KAP 140 Installation Option (if applicable) NOTE: Only use if a Honeywell KAP 140 AFCS is installed. A KC140 controller is installed in the instrument panel. All 2007 and later Models only installed the Garmin GFC 700 AFCS autopilot. Cessna NAV III KN63 DME Installation Option (if applicable) NOTE: All airplanes equipped with the Cessna NAV III KN 63 DME installation option have a DME antenna installed on the bottom of the fuselage below the cabin. Cessna NAV III KR 87 ADF Installation Option (if applicable) NOTE: Airplanes equipped with the NAV III KR 87 ADF installation option have a receiver installed on the instrument panel. Cessna NAV III BP 2007 Comant CI Antenna Configuration NOTE: For WAAS equipped airplanes without a stand alone XM Antenna (CI ). Cessna NAV III (Pre 2007 Model Year Airplanes) Comant CI Antenna Configuration NOTE: All Pre 2007 Model Year Airplanes not equipped with WAAS are equipped with the Comant CI antenna. Cessna NAV III Disable SVT Pathways Option (if desired) NOTE: Most installations will not use this option. Page 10 January 18, 2011

11 TABLE 4- Models 206H and T206H 206H/T206H AIRPLANE MODEL CONFIGURATION FILE SELECTIONS - PULL-DOWN MENU Cessna 206H B Full Configuration (WAAS) or Cessna T206H B Full Configuration (WAAS) as applicable NOTE: All GFC 700 equipped 206H/T206H airplanes are WAAS airplanes. Cessna 206H GFC 700 Installation Option or Cessna T206H GFC 700 Installation Option as applicable NOTE: All 206H and T206H NAV III 2007 and on Model Year airplanes are equipped with the GFC 700. Cessna NAV III CO Guardian Installation Option NOTE: All NAV III 2006 and on Model Year airplanes have the CO Guardian installed. Cessna NAV III CAN BUS FUEL LEVEL SENSORS (if applicable) NOTE: All NAV III 2008 and on Model Year airplanes have the CAN BUS FUEL LEVEL SENSORS installed. Cessna NAV III INITIALIZE FUEL CAL DATA (only for CAN Bus sensors before fuel cal) NOTE: Only use if CAN Bus fuel sensors are installed and a full fuel calibration must be performed on the aircraft. Do not select this option unless a fuel calibration is required, otherwise loss of fuel calibration data will result and a full fuel calibration must be performed. Cessna NAV III KTA 870 TAS Installation Option (if applicable) NOTE: All airplanes equipped with the Cessna NAV III KTA 870 TAS have a TAS circuit breaker installed on the circuit breaker panel. NOTE: All airplanes equipped with the Cessna NAV III KTA 870 TAS have a directional TAS antenna installed on the top of the airplane and a TAS antenna installed on the bottom of the airplane. Cessna NAV III KAP 140 Installation Option (if applicable) NOTE: Only use if a Honeywell KAP 140 AFCS is installed. A KC140 controller is installed in the instrument panel. All 2007 and later Models only installed the Garmin GFC 700 AFCS autopilot. Cessna NAV III KN63 DME Installation Option NOTE: All airplanes equipped with the Cessna NAV III KN 63 DME installation option have a DME antenna installed on the bottom of the fuselage below the cabin. Cessna NAV III KR 87 ADF Installation Option NOTE: Airplanes equipped with the NAV III KR 87 ADF installation option have a receiver installed on the instrument panel. Cessna NAV III BP 2007 Comant CI Antenna Configuration NOTE: For WAAS equipped airplanes without a stand alone XM Antenna (CI ) Cessna NAV III Pre BP 2007 Comant CI Antenna Configuration NOTE: All Pre 2007 Model Year Airplanes not equipped with WAAS are equipped with the Comant CI antenna. Cessna NAV III Disable SVT Pathways Option (if desired) NOTE: Most installations will not use this option. January 18, 2011 Page 11

12 TABLE 5- Configuration Selections Cessna (Model) 006-B Full Configuration (WAAS) NOTE: Use this table to list the necessary configuration uploads for the specified airplane installation. CAUTION: FAILURE TO FOLLOW THE INSTRUCTIONS IN EXACT STEP-BY-STEP ORDER COULD RESULT IN DAMAGE TO THE GDU SUPPLEMENTAL DATABASE AND/OR SD CARDS. 4. Do the preparation of the airplane for the software update as follows: A. Remove the GDU Supplemental Data SD Cards from the bottom slot of the PFD and the MFD units. B. Mark the SD Cards PFD or MFD. C. Remove the electronic checklist SD card from the top slot of the MFD as applicable. (1) If the SD cards are Garmin P/N , go to Step 5. (2) If the SD cards are not Garmin P/N , go to Step Remove the AOPA database from the database cards. If you do not remove the AOPA database file, a system error will occur because the previous system software will make the AOPA database invalid. A new AOPA database file must be installed if you want an AOPA database. A. Put the database card into a PC card reader. B. Use Windows Explorer to navigate through the contents of the database card. C. Go to Tools, then Folder Options, and then View tab. (1) Select Show hidden files and folders. (2) Uncheck Hide protected operating system files (Recommended). D. Look for the file apt_dir.gca. If it shows, select and delete it. E. Remove the database card from the PC. F. Do Step 5A thru 5E again for all cards. G. Store the cards in a safe location for later installation. 6. Load the GDU (PFD1 and MFD) software as follows: A. Make sure that all switches are in the OFF/NORM position. B. Connect the airplane to an external power unit. C. Make sure that no SD cards are installed in the PFD and MFD slots. D. Make sure that the PFD (ESS BUS and AVN BUS 1) and the MFD (AVN BUS 2) circuit breakers are disengaged. E. Insert the 006-B SD card into the topcardslotofthemfd. F. Put the BAT MASTER switch to the ON position. Page 12 January 18, 2011

13 G. Put the AVIONICS MASTER switches to the ON position and put the STDBY BATT switch to ARM. H. Push and hold the ENT key on the MFD and engage the MFD (AVN BUS 2) circuit breaker. I. Release the softkey after the INITIALIZING SYSTEM message appears. J. Push the YES soft key to upload GDU system files when the messages that follows shows: DO YOU WANT TO UPDATE SYSTEM FILES? K. If the message that follows shows, push the YES soft key: DO YOU WANT TO UPLOAD THE SPLASH SCREEN? L. Push the ENT key when the splash screen update is complete and you are asked to PRESS ANY SOFTKEY TO CONTINUE. M. Software load to the MFD is complete when the display starts into configuration mode. N. Leave the MFD display powered on. O. Remove the 006-B Garmin SD Card from the MFD and insert it into the top PFD slot. P. Engage the PFD (ESS and AVN BUS 1) circuit breakers and do Steps 6H thru 6M again for the PFD. 7. Initial software load and configuration upload. A. Turn the small FMS knob on the PFD to go to the system group SYSTEM UPLOAD page. B. Use the FMS knob to select the correct airframe from the pull-down menu. C. Push the FMS knob to start the cursor. D. Turn the small FMS knob to highlight the applicable airplane model. E. Push the ENT key. F. Select the applicable Cessna (Model Number) 006-B Full Configuration (WAAS) menu option and push the ENT key. NOTE: The software included in the 006-B SD Card will automatically determine which files must be loaded. G. Press the LOAD softkey to load selected software/config items. Periodically monitor the loading process for failures. A green PASS message is shown beside software and configuration items. NOTE: Periodically monitor the software load for progress. If the upload to a unit is unsuccessful, an UPLOAD FAIL message will be posted and the upload will stop. A red FAIL will be shown beside the software that failed. Press enter to acknowledge the fail message and to continue the same software load. If unable to load the software after several attempts, uncheck the software and configuration boxes using the ENT softkey and press the LOAD softkey to continue with the rest of the software load before troubleshooting cause of failure. H. Monitor the upload status. When the Upload Complete message is shown, push the ENT key to select OK. NOTE: Thiscantakeupto60minutes. WARNING: DO NOT CONFIGURE AN OPTION THAT IS NOT INSTALLED ON THE AIRPLANE. 8. For airplanes equipped with additional items as shown in TABLES 2, 3, or 4 (refer to TABLE 5), do the necessary uploads as follows: A. Turn the large FMS knob counterclockwise to go to the FILE menu. B. Turn the small FMS knob to expand the FILE pull down menu field and highlight one of the Cessna Nav III software uploads that is applicable for your airplane. January 18, 2011 Page 13

14 C. Push the ENT key. D. Push the LOAD soft key to install the software. E. Monitor the upload status. When the Upload Complete message is shown, push the ENT key to select OK. F. Do Steps 8A thru 8E again until all applicable (refer to TABLE 5) software uploads are complete. G. Press the FMS knob to unselect the cursor. 9. Do the PFD configuration module update: A. Push the UPDT CFG softkey. B. Select YES and push the ENT key when the UPDATE CONFIG MODULE? message shows. C. Push the ENT key to select OK after you see the UPDATE CONFIG COMPLETE message. 10. Complete the basic software load and system verification procedures as follows: A. Do the manifest configuration verification: (1) On the PFD, turn the large FMS knob to go to the SYSTEM group. Turn the small FMS knob to go to the MANIFEST CONFIGURATION page. (2) (Refer to TABLE 6.) Make sure that the data file and file version shown in TABLE 6 are shown in the SYSTEM field window. TABLE 6. Data File File Version 006-B (3) Make sure that the applicable information shown in TABLE 7 is shown in the MANIFEST field window. NOTE: This data file is near the bottom of the list. TABLE 7. Model Data File File Version 172R/172S 006-D T/T182T 006-D H/T206H 006-D B. (For airplanes equipped with CAN BUS Fuel Level Sensors only) Do the fuel configuration verification: (1) On the PFD, turn the large FMS knob to go to the CAL page group. Turn the small FMS knob to go to the FUEL TANK CALIBRATION page. (2) Push the TNK SEL soft key to highlight the CURRENT TANK field. (3) Turn the small FMS knob to expand the drop down menu to highlight the LEFT tank. (4) Push the ENT key. (5) On the PFD, make sure that several values in 2.00GL ACTUAL QUANTITY increments are shown in the CALIBRATION TABLE. (a) If several values in 2.00GL ACTUAL QUANTITY increments are shown in the CALIBRATION TABLE, go to Step 10B(6). Page 14 January 18, 2011

15 (b) If several values in 2.00GL ACTUAL QUANTITY increments are not shown in the CALIBRATION TABLE, do as follows: 1 Turn the large FMS knob on the PFD to go to the SYSTEM group and turn the small FMS knob to go to the SYSTEM UPLOAD page. 2 PushthesmallFMSknobonthePFDtostartthecursor. 3 Turn the small FMS knob to highlight the applicable airplane model and push the ENT key. 4 Turn the large FMS knob counterclockwise to go to the FILE menu. 5 Turn the small FMS knob to expand the FILE pull down menu field and highlight the NAV III CAN BUS FUEL LEVEL SENSORS option. 6 Push the ENT key. 7 Push the LOAD soft key to install the software. 8 Monitor the upload status. When the Upload Complete message is shown, push theentkeytoselectok. 9 If a software or configuration upload shows a failure, the software upload process will stop, and you must do the software upload procedure again. Do Steps 10B(5)(b)7 thru 10B(5)(b)9 again as necessary up to a total of five times until you successfully complete the configuration upload. If after five times the software configuration fails, correct the hardware failure and start the configuration upload again. 10 PushthesmallFMSknobtostopthecursor. 11 Push the UPDT CFG soft key. 12 Select YES and push the ENT key when the UPDATE CONFIG MODULE? message shows. 13 PushtheENTkeytoselectOKafteryouseetheUPDATE CONFIG COMPLETE message. 14 PushthesmallFMSknobtostopthecursor. (6) Push the TNK SEL soft key to highlight the CURRENT TANK field. (7) Turn the small FMS knob to highlight the RIGHT tank. (8) Push the ENT key. (9) On the PFD, make sure that several values in 2.00GL ACTUAL QUANTITY increments are shown in the CALIBRATION TABLE. (a) If several values in 2.00GL ACTUAL QUANTITY increments are shown in the CALIBRATION TABLE, go to Step 11. (b) If several values in 2.00GL ACTUAL QUANTITY increments are not shown in the CALIBRATION TABLE, do as follows: 1 Turn the large FMS knob on the PFD to go to the system group SYSTEM UPLOAD page. 2 PushthesmallFMSknobonthePFDtostartthecursor. 3 Turn the small FMS knob to highlight the applicable airplane model and push the ENT key. 4 Turn the large FMS knob counterclockwise to go to the FILE menu. 5 Turn the small FMS knob to expand the FILE pull down menu field and highlight the NAV III CAN BUS FUEL LEVEL SENSORS option. 6 Push the ENT key. January 18, 2011 Page 15

16 7 Push the LOAD soft key to install the software. 8 Monitor the upload status. When the Upload Complete message is shown, push theentkeytoselectok. 9 If a software or configuration upload shows a failure, the software upload process will stop, and you must do the software upload procedure again. Do Steps 10B(9)(b)7 thru 10B(9)(b)9 again as necessary up to a total of five times until you successfully complete the configuration upload. If after five times the software configuration fails, correct the hardware failure and start the configuration upload again. 10 Push the small FMS knob to stop the cursor. 11 Push the UPDT CFG soft key. 12 Select YES and push the ENT key when the UPDATE CONFIG MODULE? message shows. 13 Push the ENT key to select OK after you see the UPDATE CONFIG COMPLETE message. 14 Push the small FMS knob to stop the cursor. 11. Put the AVIONICS and BAT MASTER switches in the off position. 12. Make sure that the STDBY BATT switch is in the off position. 13. Remove the SD card from the top slot on the MFD. 14. Do the system checks as follows: A. Install the GDU Supplemental Data SD Cards in to the bottom slot on the PFD and the MFD units. B. Install the Electronic Checklist SD Card in to the top slot on the MFD. C. Put the BAT MASTER switch to the ON position. D. Put the AVIONICS MASTER switches to the ON position. E. Make sure that no G1000 system messages, alerts, annunciations, or Red X s are shown on the PFD or the MFD on the AUX-SYSTEM STATUS page. NOTE: Reference Garmin Line Maintenance Manual Revision P (or later revision) for troubleshooting instructions. F. Do the GFC-700 Autopilot Operation Checks in accordance with Section of the Garmin G1000 NAV III Line Maintenance Manual. (Refer to the Garmin G1000 NAV III Line Maintenance Manual, Part Number , Revision P (or latest revision).) 15. Put the AVIONICS and BAT MASTER switches in the off position. 16. Make sure that the STDBY BATT switch is in the off position. 17. Remove external power receptacle. 18. Make an entry in the airplane logbook that states compliance and method of compliance with this Service Bulletin. 19. (For airplanes equipped with TAWS-B) Do the enablement of Garmin G1000 Terrain Awareness Warning System Class-B (TAWS-B), SB Revision 1 or later revision. 20. (For airplanes equipped with Chartview) Do the Garmin G1000 NAV III Avionics Chartview Option, SB Revision 1 or later. NOTE: Airplanes equipped with GDU Supplemental Database SD Cards will do the same procedures as cards described in SB Revision 1 or later. 21. (For airplanes equipped with Garmin Synthetic Vision Technology) Do the enablement of Garmin G1000 Synthetic Vision Installation, SB (or latest revision). Page 16 January 18, 2011

17 22. (For airplanes equipped with Garmin Search and Rescue) Do the Garmin G1000 Search and Rescue Enablement, SB (or latest revision). 23. If necessary, do the Standby Battery Ammeter Calibration Procedure. (Refer to Section 2.2 of the Garmin G1000 NAV III Line Maintenance Manual Revision P (or latest revision).) NOTE: GDU software version is with installed. OWNER NOTIFICATION On January 18, 2011 the following message will be sent to applicable owners of record in A. Dear Cessna Restart Owner: This Owner Advisory is to inform you that has been issued. Version software provides enhancements to the Garmin G1000 avionics system. provides a software upgrade that includes the following changes: TAWS-B Alerting If installed, implemented terrain clearance and destination airport algorithm changes to reduce nuisance alerts New XM Weather Product, Aviator Pro If installed, implemented display support for AIREP, PIREP, Turbulence, Icing Potential, and Super-Cooled Liquid Droplets Weather Map Orientation Enhanced to make orientation pilot selectable instead of always "north-up" Temporary Flight Restrictions (TFR) Enhanced depiction by combining overlapping TFR circles into a single-shape TFR Course Tracking and Intercept Logic Implemented navigation system changes to improve course intercept and navigation Flight Plan Sequencing Enhanced so that manual activation of a procedure turn will not result in a suspend-state after completing the turn GFC-700 Roll Steering Updated calculations to eliminate the possibility of a roll steering over-correction when engaging the GFC-700 Autopilot Dead Reckoning Mode Added option to allow GPS course and roll steering data to be valid for up to 20 minutes after entering Dead Reckoning (DR) mode Minimum Altitude Alerts Modified so that a previously entered value is cleared when an approach is added to or deleted from the active flight plan Flight Plan Import/Export Provides capability to import and export flight plans between an SD card and the GDU flight plan memory NAV III Engine Gauges Enhanced appearance of the engine gauges to Garmin s 3D EIS Inset Maps Corrected inset map depictions so that they are always synchronized on the PFD and MFD Flight Path Marker (FPM) If Synthetic Vision is installed, the marker was modified to render behind the aircraft symbol and flight director command bars Default Waypoint Storage Duration Updated to allow the pilot to create new user-defined waypoints as either persistent or temporary and to set the defaults NAV III System Configuration Bar END (endurance), FOB (fuel on board), and FOD (fuel over destination) options are now displayed on the MFD status bar Resolution for Garmin Service Advisory No. 0904A If Synthetic Vision is installed, Pathways is now enabled Fixed Content Data Logging Provides capability of logging flight data to a comma-separated-value (CSV) file on an SD card in the upper MFD slot January 18, 2011 Page 17

18 GTS800 TAS System Input/Output Communication If installed via field approval, allows input/output communication on RS-232 and ARINC-429 interfaces Resolution for Garmin Service Advisory No Change implemented to prevent the possibility of flagging primary flight data, COM frequency, and EIS information while all stored flight plans or user waypoints are being deleted Resolution for Garmin Service Advisory No Change implemented to allow an LPV approach to be selected at airports with 3-character identifiers Multiple Waypoint Instances Modified the Flight Plan List so that any instance of a waypoint that appears multiple times can be selected, not just the first AOPA Airport Directory Information Support added for display on the "WPT-Airport Information" page. Field aircraft will need to purchase the AOPA directory via Auto Zoom Range On moving map enhanced to show active leg instead of the entire leg that is ahead of the aircraft GDU 1044B -10 Display Hardware Support Implemented software to support hardware that allows potential for external video inputs Approach Loading Cursor Operation Whenloadinganapproach,thecursorwillnolongerskipthe "minimums" field after selecting a transition that prompts for whether to fly the course reversal Display of Groundspeed in DR Mode When DR mode is active, groundspeed is now displayed in yellow on the PFD MFD Page Navigation Updated the MFD selection window to show the Page Group and Page Title for selection. provides parts and instructions to upgrade the Garmin G1000 software to version Compliance is Recommended: Should be accomplished within the next 100 hours of operation or 12 months, whichever occurs first. The information contained in the referenced Cessna Service Bulletin shall be considered an amendment to the Cessna Manufacturer's Service/Maintenance Manual and should be accomplished within the specified time requirement. Page 18 January 18, 2011

19 For airplanes out of warranty: Applicable software CD parts credit will be provided to load the software upgrade. For airplanes in warranty: Applicable Cockpit Reference Guide (CRG) and software CD parts credit and a labor allowance credit of 3.5 man-hours per airplane will be provided to load the software upgrade. for airplanes equipped with the Garmin G1000 Terrain Awareness System (TAWS-B). for airplanes equipped with the Garmin G1000 Chartview System. for airplanes equipped with Garmin G1000 Synthetic Vision Technology (SVT). for airplanes equipped with Garmin G1000 Search and Rescue. If necessary, 0.3 man-hour to do the Standby Battery Ammeter Battery Calibration Procedure For airplanes with SVT previously installed (in or out of warranty): Applicable CRG and software CD parts credit and a labor allowance credit of 3.5 man-hours per airplane will be provided to load the software upgrade. Only Authorized Service Facilities providing proof of SVT installation may submit a Warranty Claim to accomplish this Service Bulletin. for airplanes equipped with the Garmin G1000 Terrain Awareness System (TAWS-B). for airplanes equipped with the Garmin G1000 Chartview System. for airplanes equipped with Garmin G1000 Synthetic Vision Technology (SVT). for airplanes equipped with Garmin G1000 Search and Rescue. If necessary, a labor allowance credit of 0.3 man-hour will be provided to do the Standby Battery Ammeter Battery Calibration Procedure. NOTE: Proof of SVT purchase is a logbook entry or a purchasing receipt. Freight will be credited at the most economical method unless pre-approved by Cessna. For pre-approval contact Cessna Service Parts and Programs Warranty Administration at Telephone: , Fax: or cpd2claims@cessna.textron.com. To receive credit, the work must be completed and a Warranty Claim submitted by a Cessna Single Engine Authorized Service Facility within 30 calendar days of Service Bulletin compliance before the credit expiration dates shown below. Domestic... January18,2012 International... January18,2012 Special Note to Service Stations: When you complete the Warranty Claim, the labor allowance claimed shall be itemized for each above action completed. * * * * * * * January 18, 2011 Page 19

20

SERVICE BULLETIN REVISION TRANSMITTAL

SERVICE BULLETIN REVISION TRANSMITTAL REVISION TRANSMITTAL TO: Cessna Distributors, Single Authorized Service Facilities and CPC's SUBJECT: Single Service Bulletin Revision 2: Navigation - Garmin G1000 System Software Upgrade to Version 0563.26

More information

NOTE: SB is a WAAS only supported build. If the autopilot is not WAAS equipped, the unlock card cannot be used at this time.

NOTE: SB is a WAAS only supported build. If the autopilot is not WAAS equipped, the unlock card cannot be used at this time. Single Engine Service Bulletin July 22, 2011 TITLE GARMIN G1000 / FLINT AERO, INC AUXILIARY FUEL GALLON REMAINING ENABLEMENT EFFECTIVITY The following airplanes equipped with the Garmin G1000 Nav III Avionics

More information

SERVICE INFORMATION NO. SI

SERVICE INFORMATION NO. SI Diamond Aircraft Industries G.m.b.H. N.A. Otto-Straße 5 A-2700 Wiener Neustadt Austria DAI SI 42-141 Page 1 of 1 25-Aug-2010 FT SERVICE INFORMATION NO. SI-42-141 : SI s are used only: 1) To distribute

More information

Service Bulletin No.: D42L Rev 0 Date Issued: 06 June 2016 Title: GTX 33ES Installation Page: 1 of 6

Service Bulletin No.: D42L Rev 0 Date Issued: 06 June 2016 Title: GTX 33ES Installation Page: 1 of 6 Title: GTX 33ES Installation Page: 1 of 6 1. ATA Code: 3450 2. Effectivity: All DA42 aircraft with TCCA STC SA09-54 or FAA STC SA02725NY installed with Garmin GIA 63W (WAAS). 3. General: This Service Bulletin

More information

SERVICE BULLETIN NAVIGATION - GARMIN G1000 SYSTEM UPGRADES INCLUDING TERRAIN AWARENESS AND WARNING SYSTEM (TAWS-B) FUNCTION PER STC SA01725SE

SERVICE BULLETIN NAVIGATION - GARMIN G1000 SYSTEM UPGRADES INCLUDING TERRAIN AWARENESS AND WARNING SYSTEM (TAWS-B) FUNCTION PER STC SA01725SE Beechcraft TITLE: NAVIGATION - GARMIN G1000 SYSTEM UPGRADES INCLUDING TERRAIN AWARENESS AND WARNING SYSTEM (TAWS-B) FUNCTION PER STC SA01725SE SYNOPSIS OF CHANGE This Service Bulletin (SB) has been revised

More information

This Service Bulletin is applicable only to airplanes equipped with placards that are written in English.

This Service Bulletin is applicable only to airplanes equipped with placards that are written in English. Caravan Service Bulletin June 25, 2007 TITLE FUEL CAPACITY PLACARD REPLACEMENT EFFECTIVITY This Service Bulletin is applicable only to airplanes equipped with placards that are written in English. The

More information

All KODIAK 100 Series Aircraft; see Compliance section below for details of applicability.

All KODIAK 100 Series Aircraft; see Compliance section below for details of applicability. KODIAK MANDATORY SERVICE BULLETIN SB12-04 NUMBER: SB12-04 REVISION: 00 DATE: May 31, 2012 SUBJECT: KODIAK 100 Fuel Quantity Calibration *MANDATORY SERVICE BULLETIN* EFFECTIVITY: All KODIAK 100 Series Aircraft;

More information

Service Information Letter

Service Information Letter Service Information Letter Open Rotor Circuit 9910591 Series Alternators Issue Date: December 20, 2006, Revision 1 Original Issue Date: November 29, 2006 INTRODUCTION: Kelly Aerospace Turbine Rotables

More information

SERVICE NOTICE. 1. The configuration of each Garmin LRU specific to the KODIAK The Garmin LRU software.

SERVICE NOTICE. 1. The configuration of each Garmin LRU specific to the KODIAK The Garmin LRU software. SUBJECT: G1000 Configurations and Updates EFFECTIVITY: As required BACKGROUND This Service Notice is to make customers aware of the different software configurations available for their G1000-equipped

More information

It has been determined that some airplanes may have a hose plug installed in the inflatable belt assembly hose end.

It has been determined that some airplanes may have a hose plug installed in the inflatable belt assembly hose end. Single Engine Service Bulletin November 19, 2007 TITLE AMSAFE INFLATABLE RESTRAINTS HOSE PLUG INSPECTION EFFECTIVITY Group A airplanes: The following airplanes were delivered from the factory equipped

More information

FAA approval has been obtained on technical data in this publication that affects airplane type design.

FAA approval has been obtained on technical data in this publication that affects airplane type design. Caravan Service Bulletin July 20, 2010 TITLE RIGHT INBOARD FLAP BELL CRANK BEARING INSPECTION / REPLACEMENT EFFECTIVITY The airplanes that follow that have had part number S3952-5 Bearing(s) installed

More information

G1000 Synthetic Vision & Pathways Option

G1000 Synthetic Vision & Pathways Option G1000 Synthetic Vision & Pathways Option Activation Instructions For G1000 Installations in Diamond DA40 / DA40 F Aircraft Contains Instructions for Continued Airworthiness for STC #SA01480WI-D 190-00545-10

More information

Affected , RX, , and RX alternators in Service Station stock should be returned to Cessna.

Affected , RX, , and RX alternators in Service Station stock should be returned to Cessna. Single Engine Service Bulletin December 18, 2006 TITLE 60 AMPERE ALTERNATOR BRUSH REPLACEMENT EFFECTIVITY The following airplanes currently equipped with part number 9910591-11, 9910591-11RX, 9910591-12

More information

SERVICE INFORMATION NO. SI

SERVICE INFORMATION NO. SI Diamond Aircraft Industries GmbH N.A. Otto-Straße 5 A-2700 Wiener Neustadt Austria DAI SI-40-139 Page 1 of 2 24-Oct-2013 FT SERVICE INFORMATION NO. SI-40-139 NOTE: SI s are used only: 1) To distribute

More information

Single Engine. Service Bulletin TITLE ELEVATOR TRIM TAB ACTUATOR ASSEMBLY INSPECTION EFFECTIVITY. Group A airplanes: Serial Numbers

Single Engine. Service Bulletin TITLE ELEVATOR TRIM TAB ACTUATOR ASSEMBLY INSPECTION EFFECTIVITY. Group A airplanes: Serial Numbers Single Engine Service Bulletin March 12, 2007 TITLE ELEVATOR TRIM TAB ACTUATOR ASSEMBLY INSPECTION EFFECTIVITY Group A airplanes: Model Serial Numbers 172R 17281353 thru 17281364, 17281369 thru 17281372

More information

SUBJECT: Single Engine Service Bulletin SB Revision 1: Cosmetic Window Repair

SUBJECT: Single Engine Service Bulletin SB Revision 1: Cosmetic Window Repair Revision Transmittal TO: Cessna Distributors, Single Engine Service Stations SUBJECT: Single Engine Service Bulletin Revision 1: Cosmetic Window Repair REASON FOR REVISION To revise the Compliance section

More information

*MANDATORY SERVICE BULLETIN*

*MANDATORY SERVICE BULLETIN* NUMBER: SB11-12 REVISION: 00 DATE: 08/05/2011 EFFECTIVITY: KODIAK 100 Series Aircraft Serial Numbers: 100-0001 through 100-0054. KO D I A K SUBJECT: FUEL QUANTITY CALIBRATION PROCEDURES SUMMARY: It has

More information

SERVICE LETTER. Single Engine SEL TITLE LANDING GEAR - DRAG LINK REPLACEMENT

SERVICE LETTER. Single Engine SEL TITLE LANDING GEAR - DRAG LINK REPLACEMENT SERVICE LETTER TITLE LANDING GEAR - DRAG LINK REPLACEMENT EFFECTIVITY Group A Airplanes: The following airplane serial numbers were delivered with a suspect 1243600-1 Drag Link Assembly: MODEL SERIAL NUMBERS

More information

MANDATORY SERVICE BULLETIN NO. MSB D4-045/9

MANDATORY SERVICE BULLETIN NO. MSB D4-045/9 Page 1 of 9 MANDATORY SERVICE BULLETIN NO. MSB D4-045/9 SUPERSEDES MSB D4-045/8 I TECHNICAL DETAILS I.1 Category Mandatory. I.2 Airplanes affected Type: Serial s: DA 40 D 40.080, 40.084, D4.001 and subsequent,

More information

G600 PFD/MFD System Instructions for Continued Airworthiness as installed in

G600 PFD/MFD System Instructions for Continued Airworthiness as installed in Instructions for Continued Airworthiness as installed in (Make and Model Airplane) Reg. No. S/N Dwg. Number: 190-00601-00 Rev. A Garmin Ltd. Or its subsidiaries c/o Garmin International, Inc. 1200 E. 151st

More information

SERVICE BULLETIN. COMPLIANCE MANDATORY. This service bulletin must be accomplished at the next 100-hour or 12-month (annual-type) inspection.

SERVICE BULLETIN. COMPLIANCE MANDATORY. This service bulletin must be accomplished at the next 100-hour or 12-month (annual-type) inspection. TITLE EQUIPMENT/FURNISHINGS - SEAT BELT BRACKET INSPECTION EFFECTIVITY MODEL SERIAL NUMBERS 120 8000 thru 15075 140 8000 thru 15075 REASON Cessna Aircraft Company wishes to update the seat belt bracket

More information

Please replace any copy of SEB07-2 with the attached copy of SEB07-2 Revision 1 which is printed in its entirety.

Please replace any copy of SEB07-2 with the attached copy of SEB07-2 Revision 1 which is printed in its entirety. Revision Transmittal May 14, 2007 TO: Cessna Distributors, Single Engine Service Stations and CPC's SUBJECT: Single Engine Service Bulletin SEB07-2 Revision 1: Engine Mount Bracket Inspection. REASON FOR

More information

SERVICE BULLETIN REVISION TRANSMITTAL

SERVICE BULLETIN REVISION TRANSMITTAL REVISION TRANSMITTAL This sheet transmits Revision 1 to, which: A. Rearranges the sub-steps in Step 5 for better flow. NOTE: There are no technical changes in Step 5. B. Adds Steps 6 thru 9 to the Accomplishment

More information

Single Engine. Service Bulletin TITLE ENGINE MOUNT BRACKET INSPECTION

Single Engine. Service Bulletin TITLE ENGINE MOUNT BRACKET INSPECTION Single Engine Service Bulletin April 16, 2007 TITLE ENGINE MOUNT BRACKET INSPECTION EFFECTIVITY Model Year Serial Numbers 172 1956 thru 1959 28000 thru 29999 172 1956 thru 1959 36000 thru 36999 172 1956

More information

SERVICE BULLETIN SB

SERVICE BULLETIN SB TITLE COMMUNICATIONS - AUTOMATIC FLIGHT INFORMATION SYSTEM (AFIS) DATA MANAGEMENT UNIT (DMU) UPGRADE EFFECTIVITY MODEL SERIAL NUMBERS 750 (Citation X) -0001 thru -0283 The equivalent of this service bulletin

More information

ATTACHMENT. Orders for the required parts listed below must be placed by using this form only. Service Station/Company Code: Company Name:

ATTACHMENT. Orders for the required parts listed below must be placed by using this form only. Service Station/Company Code: Company Name: Single Engine ATTACHMENT CREW SEAT RECLINE MODIFICATION SB04-25-01 Revision 4 Orders for the required parts listed below must be placed by using this form only. NOTE: All web orders for these kits/parts

More information

Single Engine. Service Bulletin TITLE PILOT AND COPILOT SECONDARY SEAT STOP INSTALLATION

Single Engine. Service Bulletin TITLE PILOT AND COPILOT SECONDARY SEAT STOP INSTALLATION Single Engine Service Bulletin May 14, 2007 TITLE PILOT AND COPILOT SECONDARY SEAT STOP INSTALLATION EFFECTIVITY Model Year Serial Numbers 170 1948 18000 thru 18729 170A 1949 thru 1951 18730 thru 19400

More information

Single Engine MODIFICATION KIT

Single Engine MODIFICATION KIT Single Engine MODIFICATION KIT TITLE SECURITY LOCK INSTALLATION EFFECTIVITY Model Serial Numbers 172R 17280001 and On 172S 172S8001 and On 182S 18280001 thru 18280944 182T 18280945 and On T182T T18208001

More information

Indicating. 1. General. A. Fuel Quantity. B. Fuel Flow

Indicating. 1. General. A. Fuel Quantity. B. Fuel Flow Indicating GENERAL 28-40: INDICATING. General A. Fuel Quantity A dual reading fuel quantity indicator is displayed in the Fuel Qty block of the ENGINE page along calibrated vertical bars. The fuel quantity

More information

LOG OF REVISIONS. Model G58 Baron (Serials TH-2125 and After) Pilot s Operating Handbook and FAA Approved Airplane Flight Manual

LOG OF REVISIONS. Model G58 Baron (Serials TH-2125 and After) Pilot s Operating Handbook and FAA Approved Airplane Flight Manual LOG OF REVISIONS Model G58 Baron (Serials TH-2125 and After) Pilot s Operating Handbook and FAA Approved Airplane Flight Manual Revision A12 - May, 2015 Title Page LOEP LOR Section 1 All Reformatted to

More information

SERVICE LETTER REVISION TRANSMITTAL

SERVICE LETTER REVISION TRANSMITTAL REVISION TRANSMITTAL This sheet transmits Revision 1 to, which: A. Changes the Inspection warranty time to 0.2 from 3.0. B. Adds the note in the LABOR HOURS section. C. Adds the QR Code and internet address

More information

SERVICE BULLETIN. NO.: 0713 Revision C. All Garmin Aviation Service Centers and Aircraft OEM Service Centers DATE: 29 May 2007

SERVICE BULLETIN. NO.: 0713 Revision C. All Garmin Aviation Service Centers and Aircraft OEM Service Centers DATE: 29 May 2007 SERVICE BULLETIN NO.: 0713 Revision C TO: All Garmin Aviation Service Centers and Aircraft OEM Service Centers DATE: 29 May 2007 SUBJECT: GSM 85 Inspection Procedure REVISION B: Revision C changes some

More information

500W Series Instructions for Continued Airworthiness

500W Series Instructions for Continued Airworthiness Instructions for Continued Airworthiness Document Number Garmin International, Inc. 1200 E. 151st Street Olathe, Kansas 66062 USA Record of Revision Rev. Date Description of Change 1 10-19-06 Initial Release

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL ANALYZERS - ENGINE MONITORING. DESCRIPTION This section describes that portion of the engine indicating system which is used to analyze engine performance, temperature, and condition. Serials 00 thru 8

More information

To learn more about additional safety features available on the Matrix, visit piper.com.

To learn more about additional safety features available on the Matrix, visit piper.com. TM VALUE PROPOSITION Synonymous with value, Piper builds quality aircraft that simplify your life. The Piper Matrix is the only six-place unpressurized cabin class aircraft available today. Step into the

More information

Cessna Distributors and Single Engine Authorized Service Facilities and CPC's

Cessna Distributors and Single Engine Authorized Service Facilities and CPC's Revision Transmittal June 11, 2015 TO: Cessna Distributors and Single Engine Authorized Service Facilities and CPC's SUBJECT: Single Engine Service Bulletin, Pilot and Copilot Secondary Seat Stop Installation.

More information

SERVICE BULLETIN REVISION TRANSMITTAL

SERVICE BULLETIN REVISION TRANSMITTAL REVISION TRANSMITTAL This sheet transmits Revision 2 to, which: A. Adds the CI401-460 GPS Antenna to Step 10A and Step 10B. B. Adds the CI401-460 GPS Antenna to Figure 5. C. Adds the CI401-460 GPS Antenna

More information

500W Series Instructions for Continued Airworthiness

500W Series Instructions for Continued Airworthiness Instructions for Continued Airworthiness Document Number 190-00357-65 Rev. B Garmin Ltd. Or its subsidiaries c/o Garmin International, Inc. 1200 E. 151st Street Olathe, Kansas 66062 USA Record of Revision

More information

SERVICE BULLETIN. Citation CIB TITLE FUEL - FIREWALL SHUTOFF VALVE GROUND IMPROVEMENT

SERVICE BULLETIN. Citation CIB TITLE FUEL - FIREWALL SHUTOFF VALVE GROUND IMPROVEMENT TITLE FUEL - FIREWALL SHUTOFF VALVE GROUND IMPROVEMENT EFFECTIVITY MODEL SERIAL NUMBERS 525 (CJ1+) -0680, -0685 thru -0799 525A (CJ2+) -0417, -0439 thru -0524 525B (CJ3) -0263, -0294 thru -0414 REASON

More information

SERVICE LETTER REVISION TRANSMITTAL

SERVICE LETTER REVISION TRANSMITTAL REVISION TRANSMITTAL TO: Cessna Distributors, Multi-Engine Authorized Service Facilities, and CPC's SUBJECT: Multi-Engine Service Letter Revision 1: Hydraulic Power Pack Inspection REASON To add a coarse-threaded

More information

Company Proprietary Information

Company Proprietary Information Company Proprietary Information This document and the specifications contained herein are the property of Garmin Ltd. or its subsidiaries and may not be reproduced or used in whole or in part as the basis

More information

SERVICE BULLETIN REVISION TRANSMITTAL

SERVICE BULLETIN REVISION TRANSMITTAL REVISION TRANSMITTAL This sheet transmits Revision 2 to, which: A. Adds the reference to Figure 7, Sheet 1 and Sheet 2 to Step 10D. B. Adds Step 10D(7). C. Removes the After Modification view for PN343

More information

SERVICE LETTER SERIAL NUMBERS. 550/ thru -0505, thru -0733, thru -0969

SERVICE LETTER SERIAL NUMBERS. 550/ thru -0505, thru -0733, thru -0969 TITLE FUSELAGE - DORSAL FIN VANE INSPECTION EFFECTIVITY MODEL SERIAL NUMBERS 550/551-0002 thru -0505, -0550 thru -0733, -0801 thru -0969 REASON The equivalent of this service letter has been incorporated

More information

SERVICE BULLETIN SB

SERVICE BULLETIN SB TITLE LIGHTS - LED POSITION, TAIL POSITION, AND ANTI-COLLISION (PTA) LIGHT INSTALLATION EFFECTIVITY MODEL SERIAL NUMBERS 560 (Citation Encore) -0539 thru -0707 560 (Citation Encore+) -0751 thru -0802 NOTE:

More information

INTEGRATED ENGINE INSTRUMENT SYSTEMS

INTEGRATED ENGINE INSTRUMENT SYSTEMS All INTEGRATED ENGINE INSTRUMENT SYSTEMS. DESCRIPTION This section describes that portion of the engine indicating system which is used to analyze engine performance, temperature, and condition. Serials

More information

CREEPING LINE SEARCH PROCEDURE

CREEPING LINE SEARCH PROCEDURE CREEPING LINE SEARCH PROCEDURE Garmin Integrated Flight Deck Trainer Version 12.00 AND Updated G1000 aircraft software FOR G1000 MISSION PILOTS MISSION CO-PILOTS AND MISSION OBSERVERS FOR A CREEPING LINE

More information

SERVICE LETTER TITLE EXHAUST - TRANSMITTAL OF LYCOMING SERVICE BULLETIN NO 627C, EXHAUST SYSTEM INSPECTION SERIAL NUMBERS

SERVICE LETTER TITLE EXHAUST - TRANSMITTAL OF LYCOMING SERVICE BULLETIN NO 627C, EXHAUST SYSTEM INSPECTION SERIAL NUMBERS Single Engine MANDATORY SERVICE LETTER SEL-78-03 TITLE EXHAUST - TRANSMITTAL OF LYCOMING SERVICE BULLETIN NO 627C, EXHAUST SYSTEM INSPECTION EFFECTIVITY REASON MODEL T206H SERIAL NUMBERS T20608001 and

More information

ATTACHMENT DAMAGE REPORT FORM. Page: 1 of Pages Includes this cover sheet Date: (month/day/year) This form is for the: Left Wing: Right Wing: Other:

ATTACHMENT DAMAGE REPORT FORM. Page: 1 of Pages Includes this cover sheet Date: (month/day/year) This form is for the: Left Wing: Right Wing: Other: ATTACHMENT DAMAGE REPORT FORM TO: Cessna Aircraft Company Propeller Aircraft Customer Service/Dept 753 P.O. Box 7706 Wichita, Kansas 67277-7706 Phone Number: 316-517-5800 Fax Number: 316-942-9006 Page:

More information

SERVICE BULLETIN TITLE ENGINE CONTROLS - FULL AUTHORITY DIGITAL ENGINE CONTROL (FADEC) SOFTWARE UPGRADE VERSION C10

SERVICE BULLETIN TITLE ENGINE CONTROLS - FULL AUTHORITY DIGITAL ENGINE CONTROL (FADEC) SOFTWARE UPGRADE VERSION C10 Citation SB750-76-12 TITLE ENGINE CONTROLS - FULL AUTHORITY DIGITAL ENGINE CONTROL (FADEC) SOFTWARE UPGRADE VERSION C10 EFFECTIVITY REASON MODEL SERIAL NUMBERS 750 (Citation X) -0001 thru -0313 NOTE: Airplanes

More information

SERVICE BULLETIN SB

SERVICE BULLETIN SB TITLE LIGHTS - LED TAIL POSITION LIGHT INSTALLATION EFFECTIVITY MODEL UNIT NUMBERS 500 (Citation) -0001 thru -0349 with SB500-33-07 incorporated 500 (Citation I) -0350 thru -0528 with SB500-33-07 incorporated,

More information

2011 DAHER-SOCATA TBM850 S/N569 D-FRAS Garmin 1000 Avionics / MT 5-blade propeller

2011 DAHER-SOCATA TBM850 S/N569 D-FRAS Garmin 1000 Avionics / MT 5-blade propeller 2011 DAHER-SOCATA TBM850 S/N569 D-FRAS Garmin 1000 Avionics / MT 5-blade propeller If you want to stay in your comfort zone, but while cruising at 31,000 feet and with an approach speed slow enough to

More information

SERVICE BULLETIN. This service bulletin provides parts and instructions to install fuel caps that have a locking feature.

SERVICE BULLETIN. This service bulletin provides parts and instructions to install fuel caps that have a locking feature. TITLE FUEL - LOCKING FUEL CAP INSTALLATION EFFECTIVITY MODEL SERIAL NUMBERS 510 (Citation Mustang) -0001 and On NOTE: If the marketing designation for your airplane does not appear in the EFFECTIVITY section,

More information

SERVICE BULLETIN REVISION

SERVICE BULLETIN REVISION Revision 1 REVISION TRANSMITTAL SHEET This sheet transmits Revision 1 to, which: A. Adds a Note to the EFFECTIVITY section and Step 1 to the ACCOMPLISHMENT INSTRUCTIONS section to include a reference to

More information

SERVICE BULLETIN. EFFECTIVITY SERIAL NUMBERS 680 (Citation Sovereign) thru (Citation Sovereign+) thru -0549

SERVICE BULLETIN. EFFECTIVITY SERIAL NUMBERS 680 (Citation Sovereign) thru (Citation Sovereign+) thru -0549 TITLE DOORS - CABIN DOOR SUPPORT STRUT FITTING MODIFICATION EFFECTIVITY MODEL SERIAL NUMBERS 680 (Citation Sovereign) -0001 thru -0349 680 (Citation Sovereign+) -0501 thru -0549 REASON The equivalent of

More information

GNS 400W/500W Series SW Version 4.00 Upgrade Supplement

GNS 400W/500W Series SW Version 4.00 Upgrade Supplement GNS 400W/500W Series SW Version 4.00 Upgrade Supplement This supplement provides information regarding new features of software version 4.00 for 400W/500W Series units. The Pilot s Guide and Garmin Displays

More information

SERVICE LETTER. SERIAL NUMBERS 210 & T thru P thru P

SERVICE LETTER. SERIAL NUMBERS 210 & T thru P thru P TITLE SERVICE LETTER WINGS - LOWER MAIN SPAR CAP INSPECTION EFFECTIVITY REASON MODEL SERIAL NUMBERS 210 & T210 21058819 thru 21065009 P210 P2100001 thru P2100874 Reports have been received of cracks found

More information

CESSNA 172S NAV III VFR CHECKOUT POH EXAMINATION (Based on N1129K, serial no. 172S revised 10/05/06)

CESSNA 172S NAV III VFR CHECKOUT POH EXAMINATION (Based on N1129K, serial no. 172S revised 10/05/06) INTRODUCTION, POH CESSNA 172S NAV III VFR CHECKOUT POH EXAMINATION (Based on N1129K, serial no. 172S10315 - revised 10/05/06) 1. Rate of climb at sea level: 2. Service ceiling: 3. Takeoff performance,

More information

ATTITUDE AND DIRECTION

ATTITUDE AND DIRECTION All ATTITUDE AND DIRECTION 1. DESCRIPTION This section contains information pertaining to those portions of the system which use magnetic, gyroscopic, and inertia forces. Included is the magnetic compass,

More information

EPAS Desktop Pro Software User Manual

EPAS Desktop Pro Software User Manual Software User Manual Issue 1.10 Contents 1 Introduction 4 1.1 What is EPAS Desktop Pro? 4 1.2 About This Manual 4 1.3 Typographical Conventions 5 1.4 Getting Technical Support 5 2 Getting Started 6 2.1

More information

SERVICE BULLETIN. To prevent the wing fuel boost pump wiring from chafing on the wing structure and/or fuel tube assemblies.

SERVICE BULLETIN. To prevent the wing fuel boost pump wiring from chafing on the wing structure and/or fuel tube assemblies. TITLE FUEL - WING FUEL BOOST PUMP WIRE ROUTING IMPROVEMENT EFFECTIVITY MODEL SERIAL NUMBERS 560-0001 thru -0538 REASON To prevent the wing fuel boost pump wiring from chafing on the wing structure and/or

More information

INDULGENCE MEETS PERFORMANCE

INDULGENCE MEETS PERFORMANCE M600 INDULGENCE MEETS PERFORMANCE The perfect balance of performance and luxury, the M600 is the modern businessperson s plane. With unprecedented range, power, payload, and an obsession with safety, the

More information

TRADITION COMES STANDARD

TRADITION COMES STANDARD M350TM TRADITION COMES STANDARD Traditions are meant to be celebrated and handed down to future generations. At Piper, we believe in building on tradition, manufacturing a reliable, quality product that

More information

G1000 / GFC 700. Diamond DA 40 & DA 40 F. Instructions for Continued Airworthiness May, 2006 Revision A

G1000 / GFC 700. Diamond DA 40 & DA 40 F. Instructions for Continued Airworthiness May, 2006 Revision A G1000 / GFC 700 Instructions for Continued Airworthiness Diamond DA 40 & DA 40 F 190-00492-03 May, 2006 Revision A Copyright 2006 Garmin Ltd. or its subsidiaries All Rights Reserved Except as expressly

More information

SERVICE BULLETIN REVISION TRANSMITTAL

SERVICE BULLETIN REVISION TRANSMITTAL REVISION TRANSMITTAL This sheet transmits Revision 1 to, which: A. Adds HDWR kit to the MATERIAL INFORMATION section. NOTE: This revision replaces the original issue of in its entirety. REVISION COMPLIANCE

More information

SERVICE BULLETIN. The equivalent of this service bulletin has been incorporated on production airplanes and On.

SERVICE BULLETIN. The equivalent of this service bulletin has been incorporated on production airplanes and On. TITLE ICE AND RAIN PROTECTION - WING ANTI-ICE SYSTEM IMPROVEMENT EFFECTIVITY MODEL SERIAL NUMBERS 525B -0002 thru -0012 The equivalent of this service bulletin has been incorporated on production airplanes

More information

SERVICE BULLETIN SERIAL NUMBERS. The equivalent of this service bulletin has been incorporated on production airplanes and On.

SERVICE BULLETIN SERIAL NUMBERS. The equivalent of this service bulletin has been incorporated on production airplanes and On. TITLE FUSELAGE - TAILCONE GROUND RECEPTACLE INSTALLATION EFFECTIVITY MODEL SERIAL NUMBERS 560-0539 thru -0649 REASON The equivalent of this service bulletin has been incorporated on production airplanes

More information

Pilot's Operating Handbook Supplement AS-03

Pilot's Operating Handbook Supplement AS-03 POH / AFM SECTION 9 Pilot's Operating Handbook Supplement ASPEN EFD1000 PFD This supplement is applicable and must be inserted into Section 9 of the POH when the Aspen Avionics Evolution Flight Display

More information

SUBJECT: ELECTRICAL POWER SYSTEM UNIT AND ROTORCRAFT FLIGHT MANUAL TEMPORARY REVISION, CANCELLATION OF

SUBJECT: ELECTRICAL POWER SYSTEM UNIT AND ROTORCRAFT FLIGHT MANUAL TEMPORARY REVISION, CANCELLATION OF MODEL AFFECTED: 505 ALERT SERVICE BULLETIN 505-17-03 PSL 7000000247 28 November 2017 Revision A, 14 February 2018 Revision B, 6 March 2018 Revision C, 18 September 2018 SUBJECT: ELECTRICAL POWER SYSTEM

More information

Revision Transmittal Sheet

Revision Transmittal Sheet 2 APPROVED WHITE IN LEARJET 31 RT 31-32-24 Revision Transmittal Sheet This page transmits Revision 1 to No. 31-32-24, Main Landing Gear Torque Link Replacement. Rework: No rework is required for aircraft

More information

2015 CITATION M2 S/N N927AA

2015 CITATION M2 S/N N927AA MAX CRUISE SPEED 404 Ktas PASSENGERS 7 RANGE(NM) 1,550 SPECIFICATIONS AIRFRAME Hours Since New: 176 Cycles Since New: 166 ENGINES Williams International FJ44-1AP-21 (FADEC) LEFT ENGINE RIGHT ENGINE Serial

More information

Central Warning Systems

Central Warning Systems CIRRUS AIRPLANE MAINTENANCE MANUAL Central Warning Systems CHAPTER 31-50: CENTRAL WARNING SYSTEMS GENERAL 31-50: CENTRAL WARNING SYSTEMS 1. General This section describes the Indicating/Recording Systems

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL All ATTITUDE AND DIRECTION 1. DESCRIPTION This section contains information pertaining to those portions of the system which use magnetic, gyroscopic, and inertia forces. Included is the magnetic compass,

More information

CAPABLE AIRCRAFT MAKE PROFICIENT PILOTS

CAPABLE AIRCRAFT MAKE PROFICIENT PILOTS TR INERS CAPABLE AIRCRAFT MAKE PROFICIENT PILOTS At Piper Aircraft, we believe in training the most confident, capable pilots. We know the future of aviation depends on it, which is why we offer a complete

More information

CESSNA SECTION 4. Unless otherwise noted, the following speeds are based on a maximum weight of 2550 pounds and may be used for any lesser weight.

CESSNA SECTION 4. Unless otherwise noted, the following speeds are based on a maximum weight of 2550 pounds and may be used for any lesser weight. CESSNA SECTION 4 INTRODUCTION Section 4 provides procedures and amplified instructions for normal operations using standard equipment. Normal procedures associated with optional systems can be found in

More information

SR22 Airplane Flight Manual (AFM) Temporary Change

SR22 Airplane Flight Manual (AFM) Temporary Change Cirrus Design TPOH Airplane Flight Manual (AFM) Temporary Change Information in this Temporary Change adds to, supersedes, or deletes information in the basic Pilot s Operating Handbook. Affected Publications:

More information

AIRPLANE FLIGHT MANUAL AQUILA AT01 AIRPLANE FLIGHT MANUAL - SUPPLEMENT AVE28 GLASS COCKPIT. equipped with ASPEN EFD1000 PFD

AIRPLANE FLIGHT MANUAL AQUILA AT01 AIRPLANE FLIGHT MANUAL - SUPPLEMENT AVE28 GLASS COCKPIT. equipped with ASPEN EFD1000 PFD SECTION 9 AIRPLANE FLIGHT MANUAL - SUPPLEMENT AVE28 GLASS COCKPIT equipped with ASPEN EFD1000 PFD This AFM supplement is applicable and must be inserted into Section 9 of the Airplane Flight Manual when

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL CENTRAL WARNING SYSTEMS 1. GENERAL This section describes the Central Warning Systems which consists of a Crew Alerting System (CAS) and related sensors and switches. A. Crew Alerting System Aircraft annunciations

More information

SERVICE BULLETIN CERTIFICATION REQUIREMENTS - FOREIGN CERTIFICATION PLACARD INSTALLATION

SERVICE BULLETIN CERTIFICATION REQUIREMENTS - FOREIGN CERTIFICATION PLACARD INSTALLATION TITLE CERTIFICATION REQUIREMENTS - FOREIGN CERTIFICATION PLACARD INSTALLATION EFFECTIVITY MODEL UNIT NUMBERS 550-1040 NOTE: This Service Bulletin may only be accomplished at a Cessna-owned or an authorized

More information

SECTION 3 ENGINE INDICATION SYSTEM (EIS)

SECTION 3 ENGINE INDICATION SYSTEM (EIS) ENGINE INDICATION SECTION ENGINE INDICATION () NOTE: Refer to the Pilot s Operating Handbook (POH) for limitations. The Engine Indication System () displays critical engine, electrical, fuel, and other

More information

Attitude And Direction

Attitude And Direction CIRRUS AIRPLANE MAINTENANCE MANUAL Attitude And Direction CHAPTER 34-20: ATTITUDE AND DIRECTION GENERAL 34-20: ATTITUDE AND DIRECTION 1. General This section contains information pertaining to those portions

More information

certified aircraft GENERAL PRICE LIST 2018 P2008JC mkii P TwentyTen cs-23 - FAR 23 P2002JF

certified aircraft GENERAL PRICE LIST 2018 P2008JC mkii P TwentyTen cs-23 - FAR 23 P2002JF certified P92JS cs-vla P2002JF cs-vla P2008JC mkii aircraft cs-vla P TwentyTen cs-23 - FAR 23 p2006t cs-23 - FAR 23 GENERAL PRICE LIST 2018 CS-23 FAR 23 & CS-VLA 18040312 T1001 STANDARD ANALOGUE IFR RETRACTABLE

More information

CurveMaker DFS v2.0 Dyna FS Ignition Programming Software

CurveMaker DFS v2.0 Dyna FS Ignition Programming Software CurveMaker DFS v2.0 Dyna FS Ignition Programming Software Contents Dynatek 164 S. Valencia St. Glendora, CA 91741 phone (626)963-1669 fax (626)963-7399 page 1) Installation 1 2) Overview 1 3) Introduction

More information

EFFECTIVITY Serial Numbers thru , 698

EFFECTIVITY Serial Numbers thru , 698 Conquest TITLE AILERON HINGE BRACKET REPLACEMENT EFFECTIVITY Model Serial Numbers 441 441-0001 thru 441-0349, 698 DESCRIPTION To install stainless-steel aileron hinge brackets as a replacement for aluminum

More information

Issue 2.0 December EPAS Midi User Manual EPAS35

Issue 2.0 December EPAS Midi User Manual EPAS35 Issue 2.0 December 2017 EPAS Midi EPAS35 CONTENTS 1 Introduction 4 1.1 What is EPAS Desktop Pro? 4 1.2 About This Manual 4 1.3 Typographical Conventions 5 1.4 Getting Technical Support 5 2 Getting Started

More information

FAA approval has been obtained on technical data in this publication that affects airplane type design.

FAA approval has been obtained on technical data in this publication that affects airplane type design. Single Engine Service Bulletin January 28, 2008 TITLE ENGINE COWLING ALIGNMENT INSPECTION AND MODIFICATION EFFECTIVITY Model Serial Numbers 172R 17280725 thru 17281262 172S 172S8202 thru 172S10006 REASON

More information

Citation Mustang. Throttle Lever Rigging. TLA Rigging Guide REFERENCE ONLY

Citation Mustang. Throttle Lever Rigging. TLA Rigging Guide REFERENCE ONLY Citation Mustang Throttle Lever Rigging TLA Rigging Guide This guide is designed to assist maintenance and avionics technicians in using the Pratt & Whitney Ground Based Software or GBS to rig the throttle

More information

SERVICE BULLETIN. To prevent the wing fuel boost pump wiring from chafing on the wing structure and/or fuel tube assemblies.

SERVICE BULLETIN. To prevent the wing fuel boost pump wiring from chafing on the wing structure and/or fuel tube assemblies. TITLE FUEL - WING FUEL BOOST PUMP WIRE ROUTING IMPROVEMENT EFFECTIVITY MODEL UNIT NUMBERS 500/501-0001 thru -0689 REASON To prevent the wing fuel boost pump wiring from chafing on the wing structure and/or

More information

Service Bulletin. ATA 52-10: Passenger and Crew Doors Door Latching Assembly Upgrade

Service Bulletin. ATA 52-10: Passenger and Crew Doors Door Latching Assembly Upgrade Service Bulletin Issued: 5 Oct 00 Models SR0 and SR ATA 5-10: Passenger and Crew Doors Door Latching Assembly Upgrade COMPLIANCE Optional: Accomplishment of this Service Bulletin is at the owner s option.

More information

ALERT SERVICE LETTER

ALERT SERVICE LETTER Citation TITLE ALERT SERVICE LETTER ASL525-32-21 LANDING GEAR - TRANSMITTAL OF GOODRICH 2-1559-32-4, MAIN LANDING GEAR - BRAKE ASSEMBLY - P/N S 2-1559-1 AND 2-1559-2 - CESSNA CITATION AIRCRAFT - INTRODUCTION

More information

Service Bulletin. ATA 27-00: Flight Controls Rudder-Aileron Interconnect Modification

Service Bulletin. ATA 27-00: Flight Controls Rudder-Aileron Interconnect Modification Service Bulletin Issued: 09 May 2007 Models SR20 and SR22 ATA 27-00: Flight Controls Rudder-Aileron Interconnect Modification COMPLIANCE Mandatory: Accomplish this Service Bulletin within 25 Flight Hours

More information

TEMPORARY REVISION NUMBER

TEMPORARY REVISION NUMBER TEMPORARY REVISION NUMBER 7 DATED 1 DECEMBER 2011 MANUAL TITLE MANUAL NUMBER - PAPER COPY TEMPORARY REVISION NUMBER Model 188 & T188 Series 1966 Thru 1984 Service Manual D2054-1-13 D2054-1TR7 MANUAL DATE

More information

2008 CITATION MUSTANG SN

2008 CITATION MUSTANG SN KNOTS 340 PASSENGERS 5 RANGE (NM) 1,200 AIRCRAFT LISTING DETAILS: Total Hours: 1410 Total Landings: 1200 ENGINES: PRATT & WHITNEY PW 615F-A #1 #2 Total Hours: 1410 1410 Engine Cycles: 1210 1210 Serial

More information

CIRRUS AIRPLANE MAINTENANCE MANUAL

CIRRUS AIRPLANE MAINTENANCE MANUAL All INDICATING. DESCRIPTION A. Fuel Quantity Serials 005 thru 885: A fuel quantity gage is installed in the center console directly forward of the fuel selector valve. The fuel quantity gage indicates

More information

PROPELLERS - PROPELLER SLIP RING MOUNTING PLATE INSPECTION AND REPAIR

PROPELLERS - PROPELLER SLIP RING MOUNTING PLATE INSPECTION AND REPAIR Beechcraft TITLE: PROPELLERS - PROPELLER SLIP RING MOUNTING PLATE INSPECTION AND REPAIR 1. Planning Information A. Effectivity (1) Airplanes Airplanes that have accomplished installation of Hartzell STC

More information

SERVICE BULLETIN MANDATORY. SB , Rev Planning Information

SERVICE BULLETIN MANDATORY. SB , Rev Planning Information SERVICE BULLETIN TITLE: STABILIZERS - INSPECTION/REPLACEMENT OF ELEVATOR BALANCE WEIGHT ASSEMBLIES SYNOPSIS OF CHANGE This Service Bulletin has been revised to add a balance weight inspection every 100

More information

SmarTire TPMS Maintenance Hand Tool. Revision User Manual

SmarTire TPMS Maintenance Hand Tool. Revision User Manual SmarTire TPMS Maintenance Hand Tool Revision 1.04 User Manual Page 2 Table of Contents FCC Compliance Label... 4 User Interface Illustration... 4 Introduction... 5 Testing Tire Sensors... 5 Main Menu...

More information

CITATION MUSTANG SN RANGE (NM) PASSENGERS 4 KNOTS 340 CONTACT: DAVID LEE 1,200 I

CITATION MUSTANG SN RANGE (NM) PASSENGERS 4 KNOTS 340 CONTACT: DAVID LEE 1,200 I KNOTS 340 PASSENGERS 4 RANGE (NM) 1,200 AIRCRAFT LISTING DETAILS: Total Hours: 2000 ENGINES: Pratt & Whitney PW615F-A Left Right Total Hours: 2000 1970 Engine Cycles: 1225 1205 AIRCRAFT HIGHLIGHTS: Synthetic

More information

The engine cowling installation and firewall should be inspected and modified as specified in this Service Bulletin.

The engine cowling installation and firewall should be inspected and modified as specified in this Service Bulletin. Single Engine Service Bulletin August 25, 2008 TITLE ENGINE COWLING ALIGNMENT INSPECTION AND MODIFICATION EFFECTIVITY Model Serial Numbers 172R 17280001 thru 17280724 172S 172S8001 thru 172S8201 REASON

More information

Copyright 2017, 2018 Garmin Ltd. or its subsidiaries All Rights Reserved

Copyright 2017, 2018 Garmin Ltd. or its subsidiaries All Rights Reserved Copyright 2017, 2018 Garmin Ltd. or its subsidiaries All Rights Reserved Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or

More information

2014 Cessna Citation Mustang 510 Serial Number: 0448 Registration: N448WT

2014 Cessna Citation Mustang 510 Serial Number: 0448 Registration: N448WT Airframe: Total Hours: 96.4 Since New Total Cycles: 96.4 Since New Highlights: U.S. Registered Fresh Cessna GSO PPI/Import and 12/24 month Inspections Enrolled on Cescom No Damage History Engines enrolled

More information