Blow Off Valve Retrofit Kit

Size: px
Start display at page:

Download "Blow Off Valve Retrofit Kit"

Transcription

1 Instruction Sheet P/N 37 56C low Off Valve Retrofit Kit WRNING: llow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation.. Introduction The blow off valve eases drum change-out on Nordson Series gallon drum melters by allowing an operator to inject air below the platen with the turn of a switch. The air prevents a vacuum from forming under the platen and eases the removal of the platen from the drum when the elevator control is in the UP position. The blow off valve in this installation kit is installed in a platen heater pad and replaces a unit s existing blow off valve.. low Off Valve Installation Use these procedures to replace an existing blow off valve with the new blow off valve in this kit. Refer to the drum melter manual as necessary for component illustrations. Preparing for Installation Follow this procedure to prepare the unit for blow off valve installation.. If there is a drum in the unit, remove it by following the drum removal instructions in the drum melter manual.. Place a heat-resistant support on the frame base below the platen to allow access to the platen heater pads. 3. Use the elevator control to lower the platen onto the support. 4. Press the STOP push-button on the electrical enclosure front panel; then place the main disconnect switch in the OFF position. WRNING: Risk of electrical shock. Disconnect equipment from line voltage before servicing. 5. Disconnect and lock out electrical power to the unit. 999 Nordson Corporation 37 56C

2 low Off Valve Retrofit Kit Preparing for Installation (contd) WRNING: System or material pressurized. Relieve pressure. Failure to observe may result in serious burns. 6. Set the air pressure regulator to 0 bar/psi (fully counterclockwise); then disconnect the air supply from the unit. 7. Move the elevator control to the UP position to bleed all pneumatic pressure from the system. Removing the low Off Valve and Heater Pad Follow this procedure to remove the old blow off valve and heater pad. The new blow off valve will be installed in a new heater pad. WRNING: Wear long-sleeved, heat-protective clothing, safety goggles, and heat-protective gloves.. See Figure. Remove and discard the follower plate cover (9). Retain the screws.. Remove the blow off valve and plug the hole (8). 3. Remove the PTFE joint sealant () and clean the follower plate (7). 4. Disconnect the heater wires from the heater pad opposite the T-handle (); then remove the heater pad. Retain the screws. 5. Remove the flange screw (6) opposite the T-handle. 6. Using the screws removed in steps and 5, attach the drill template (5) to the flange (3) and drill two 7. mm (0.8 in.) holes (4) in the flange C 999 Nordson Corporation

3 low Off Valve Retrofit Kit Fig. low Off Valve and Heater Pad Removal. T-handle location. PTFE joint sealant 3. Flange 4. Drill holes 5. Drill template 6. Flange screw 7. Follower plate 8. low off valve hole 9. Follower plate cover 999 Nordson Corporation 37 56C

4 4 low Off Valve Retrofit Kit Installing the Heater Pad and low Off Valve Follow this procedure to install the new heater pad and blow off valve.. See Figure. Place PTFE joint sealant () on the new heater pad (4).. Install the heater pad using the screws removed earlier. Hand-tighten the screws. 3. Reconnect the heater pad heater wires. 4. Mount the adapter plate () on the flange using the hex nuts (6) and the screws and washers (5) from the kit. Hand-tighten the nuts, screws, and washers. 5. ttach the new blow off valve (7) to the adapter plate using the screws, lock washers, and flat washers (3) from the kit. Orient the air ports as shown in Figure C 999 Nordson Corporation

5 low Off Valve Retrofit Kit É Ç ÇÇ Ç ÇÇ ÇÇÇ ÇÇ ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ 5 Fig. SECTION 7 4 SEE DETIL Heater Pad and low Off Valve Installation. PTFE joint sealant. dapter plate 3. low off valve screw and washer 4. Heater pad DETIL dapter plate screw and washer 6. Hex nut 7. low off valve 8. T-handle location (for reference only) 999 Nordson Corporation 37 56C

6 6 low Off Valve Retrofit Kit Installing the Heater Pad and low Off Valve (contd) Fig. 3 Orientation of low Off Valve ir Ports. low off valve ports. New heater pad 6. Follow these steps to tighten the heater pad screws: a. Restore electrical power to the unit and allow the unit to reach about 77 C (350 F). WRNING: Risk of electrical shock. Disconnect equipment from line voltage before servicing. b. Turn the unit off and disconnect and lock out electrical power to the unit. WRNING: Wear long-sleeved, heat-protective clothing, safety goggles, and heat-protective gloves. c. Tighten the heater pad screws to 4 N m (30 ft lb) C 999 Nordson Corporation

7 low Off Valve Retrofit Kit 7 7. Tighten the adapter plate screws. 8. See Figure. pply PTFE joint sealant () to the adapter plate and follower plate. 9. See Figure 4. Install the follower plate cover () using the screws removed earlier. dd the two new screws () from the kit. Fig. 4 Follower Plate Cover Installation. Follower plate cover. Screw Nordson Corporation 37 56C

8 8 low Off Valve Retrofit Kit Making the ir Line Connections Follow this procedure to modify the existing air line connections and to add the new air line tubing and hose from the kit. CUTION: Do not overcoat fittings when applying PTFE paste. Overcoating can cause PTFE paste to enter the air lines and clog the air regulator or preset regulator. Use Figure 5 to make the air line modifications and connections. Lightly coat all male taper pipe thread connections with PTFE paste. Cut items 8 and 9 to the lengths specified in Figure 5. NOTE: The dashed-line portion of the illustration represents tubing and components to be removed mm (56 in.) 9 45 mm (49 in.) mm (55 in.) E P E E 0 P E Fig. 5 low Off Valve ir Line Modifications and Connections. 3 / 8 in. x / 4 NPT male elbow 6. / in. x / 4 NPT hose nipple. / 4 in. x / 4 NPT male connector 7. Tubing clamp 3. / 4 NPT pipe tee 8. / in. hose 4. / 4 NPT steel nipple 9. / 4 in. outside diameter PTFE tubing 5. 7 psi preset regulator 0. / 4 in. tube male connector. / in. x 3 / 8 NPT hose nipple. low off valve 3. / 4 in. x / 8 NPT male elbow 37 56C 999 Nordson Corporation

9 low Off Valve Retrofit Kit 9 Verifying the Installation Use Figures 6 and 7 to verify that all modifications are complete and that the new blow off valve air line tubing has been properly connected E P E 0 P E 3 7 Fig. 6 Pneumatic Diagram of Installed low Off Valve. 3 / 8 in. x / 4 NPT male elbow 6. / in. x / 4 NPT hose nipple. / 4 in. x / 4 NPT male connector 7. Tubing clamp 3. / 4 NPT pipe tee 8. / in. hose 4. / 4 NPT steel nipple 9. / 4 in. outside diameter PTFE tubing 5. 7 psi preset regulator 0. / 4 in. tube male connector / in. x 3 / 8 NPT hose nipple. low off valve 3. / 4 in. x / 8 NPT male elbow 4. To top of air cylinders (for reference only) 5. To bottom of air cylinders (for reference only) 999 Nordson Corporation 37 56C

10 0 low Off Valve Retrofit Kit Verifying the Installation (contd) SHOP IR SUPPLY ORIFICE P EXH 4 WY HND VLVE P E E 60 PSI IN LEFT CYLINDER OUT RIGHT CYLINDER REGULTOR PRESET 60 PSI REGULTOR PRESET 0 PSI TO PLTEN Fig. 7 Schematic of Installed low Off Valve Restoring the System to Normal Operation When installation is properly completed and verified, follow these steps to restore the system to normal operation.. Restore electrical power to the system and turn the system on by moving the applicator circuit breaker to the ON position.. Re-establish the air supply to the system, then set the air regulator to no less than 4.4 bar (60 psi). 3. Check for and correct any air leaks in the pneumatic system. 4. Raise the platen and remove the heat-resistant support C 999 Nordson Corporation

11 low Off Valve Retrofit Kit 3. Platen Removal Using the low Off Valve Use this procedure to change out a drum using the blow off valve. Refer to the drum melter manual for illustrations.. llow the unit to reach operating temperature. CUTION: Risk of platen seal damage. Do not continue with this procedure until the unit is at operating temperature.. Place the PUMP OFF/ON switch in the OFF position. 3. Turn the PLTEN REMOVL switch to the ON position. 4. Place the elevator control in the UP position. ir will flow from the blow off valve and the platen will begin to rise. 5. When the platen is out of the drum, turn the PLTEN REMOVL switch to the OFF position. 6. If desired, place a new drum in the unit by following the instructions in the drum melter manual. 4. Troubleshooting Use these troubleshooting procedures if the blow off valve is not working properly.. Set the air pressure regulator to 0 bar/psi.. Disconnect the air line from the blow off valve elbow fitting. 3. Slowly restore the air pressure to.38 bar (0 psi); then rotate the PLTEN REMOVL switch clockwise and slowly move the elevator control to the UP position. ir flows from the air line: normal indication. Reconnect the air line, return the elevator control to neutral, and go to step 4. No air flows from the air line: possible blockage at the PLTEN REMOVL switch or bad air line connection. Clear the blockage at the PLTEN REMOVL switch or correct the bad air line connection. 999 Nordson Corporation 37 56C

12 low Off Valve Retrofit Kit 4. Troubleshooting (contd) 4. Reset the air pressure regulator to 0 bar/psi. Disconnect the large hose from the blow off valve. 5. Slowly restore the air pressure to.38 bar (0 psi): ir flows from the hose: normal indication. Reconnect the hose and go to step 6. No air flows from the hose: defective preset regulator or bad air line connection. Repair or replace the preset regulator or correct the bad air line connection. 6. Reset the air pressure regulator to 0 bar/psi. Disconnect the air line tubing from the top of the blow off valve. 7. Slowly restore the air pressure to.38 bar (0 psi): ir flows from the air line: normal indication. Reconnect the air line and go to step 8. No air flows from the air line: possible blockage at the 3-way piloted valve or blow off valve switch or bad air line connection. Clear the blockage at the 3-way piloted valve or blow off valve switch or correct the bad air line connection. 8. If possible, visually inspect the bottom of the platen for adhesive that may be blocking the blow off valve air outlet. Remove any adhesive blocking the air outlet. 9. If none of these troubleshooting procedures resolves the problem, set the air pressure regulator to 0 bar/psi, shut off the main air supply source, remove the blow off valve and clean or rebuild it, then reinstall it C 999 Nordson Corporation

13 low Off Valve Retrofit Kit 3 5. Parts To order parts, call the Nordson Customer Service Center or contact your local Nordson representative. Use the following parts lists to describe and locate parts correctly. Item Part Description Quantity Note 38 0 Kit, retrofit, blow off valve, 00/40/480 Vac Kit, retrofit, blow off valve, 330 Vac Elbow, male, / 4 in. tube x / 4 NPT Connector, male, / 4 in. tube x / 4 NPT Tee, pipe, / 4 in Nipple, steel, schedule 40, / 4 in., 0.87 in Regulator, preset, 7 psi Nipple, hose, / in. x / 4 NPT Clamp, tubing, worm drive, in Hose, silicone, 0.50 in. ID x 0.3 in. W, 4 ft Tubing, / 4 in. OD x 0.0 in., 8 ft Connector, male, / 4 in. tube Nipple, hose, / in. x 3 / 8 NPT 36 8 Valve assembly, blow off Elbow, male, / 4 in. tube x / 8 NPT Sealant, joint, / 4 in., 4 ft Template, drill Cover assembly, follower plate Plate, adapter Screw, socket-head, M8 x Washer, lock, M, external, Washer, flat, M, regular, Heater pad, smooth, reworked, 00/40/480 Vac Heater pad, smooth, reworked, 330 Vac Screw, pan-head, recessed, M6 x 0 mm Washer, flat, M, regular, M6 C Screw, hex-head, cap, M6 x 30 mm C Nut, hex, M6 C Plug, pipe, socket, flush, 3 / 8 in. NS Sealant, paste NOTE : Used to attach the blow off valve to the adapter plate. : dditional screws for the follower plate cover. C: Used to attach the adapter plate to the follower plate. NS: Not Shown 999 Nordson Corporation 37 56C

14 4 low Off Valve Retrofit Kit 5. Parts (contd) E P E 0 P E , 9, , 4 5 É ÇÇ ÇÇ ÇÇÇÇÇ ÉÉÉ ÉÉÉ SECTION 7 SEE DETIL DETIL Fig. 8 low Off Valve Retrofit Kit Parts Original copyright date 998. Nordson and the Nordson logo are registered trademarks of Nordson Corporation C 999 Nordson Corporation

Installing the Integral Platen Blow Off Valve

Installing the Integral Platen Blow Off Valve Instruction Sheet Installing the Integral Platen Blow Off Valve WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all

More information

Preventive Maintenance for Pail Melters

Preventive Maintenance for Pail Melters Instruction Sheet P/N Preventive Maintenance for Pail Melters 1. Introduction These procedures are recommended in addition to the standard preventive maintenance. Use them to keep yourvista controlled

More information

Installation Instructions for Series 3100V Low Level Indicator

Installation Instructions for Series 3100V Low Level Indicator Instruction Sheet P/N Installation Instructions for Series 3100V Low Level Indicator WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document

More information

Inverted High Pressure Fluid Filters

Inverted High Pressure Fluid Filters Instruction Sheet P/N 33290-03 Description See Figure. Nordson high-pressure fluid filters prevent nozzle-plugging by filtering contaminants out of coating materials. These stainless steel, wall-mounted

More information

Series 3900/M Pump Retrofit Kit

Series 3900/M Pump Retrofit Kit Instruction Sheet P/N Series 900/M Pump Retrofit Kit WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related

More information

TCU Flushing Manifold and RTD Installation

TCU Flushing Manifold and RTD Installation Instruction Sheet P/N 1614041-01 This instruction is for installing temperature control unit (TCU) flush manifold and RTD assembly onto the heat exchanger for both new systems and existing systems. Follow

More information

E-200 O-rings Service Kit

E-200 O-rings Service Kit Instruction Sheet E-00 O-rings Service Kit. Introduction These instructions describe how to replace the o-rings in the E-00 gun module. It is necessary to remove and disassemble the module when replacing

More information

E-200 Module Service Kit

E-200 Module Service Kit Instruction Sheet E-200 Module Service Kit 1. Introduction These instructions describe how to remove and replace the E-200 module. The instructions include the following: S S S S Safety Unit Preparation

More information

Pro-Swirl Manifold Air Heater

Pro-Swirl Manifold Air Heater Instruction Sheet P/N 16107 01 Description The Pro-Swirl manifold heats air coming from the Pro-Swirl coalescent filter. The heater air then flows through the internal passages of the Pro-Swirl to maintain

More information

Inverted Dual High-Pressure Fluid Filter Assemblies

Inverted Dual High-Pressure Fluid Filter Assemblies Instruction Sheet P/N 1093-04 Inverted Dual High Pressure Fluid Filter Assemblies Introduction WARNG: High pressure fluids are hazardous. To prevent serious injury when installing and servicing filters,

More information

Converting an FP-200 Extrusion Gun to an FP-200 Swirl Gun

Converting an FP-200 Extrusion Gun to an FP-200 Swirl Gun Instruction Sheet P/N 237494_02 Converting an FP-200 Extrusion Gun to an FP-200 Swirl Gun WARNING! Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this

More information

Replacing a Gun RTD. Instruction Sheet P/N B. 1. Introduction. Using this Instruction Sheet

Replacing a Gun RTD. Instruction Sheet P/N B. 1. Introduction. Using this Instruction Sheet Instruction Sheet Replacing a Gun RTD WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this document and all other related documentation.

More information

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3700V 3800V 3900V

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3700V 3800V 3900V Part B, Section 1 Model Voltage Pump Manifold Control This section covers the following unit configurations. 3500V 3700V 3800V 3900V All Piston (F) 4-Port (A) 6-Port (B or C) -Port (S or T) Vista Standard

More information

Description. Rhino SD2/XD2 Type-H Control Modules. S 55-Gallon Drum with Pneumatic Changeover S 55-Gallon Drum with Electric Changeover

Description. Rhino SD2/XD2 Type-H Control Modules. S 55-Gallon Drum with Pneumatic Changeover S 55-Gallon Drum with Electric Changeover Description NOTE: Throughout this document, the Rhino SD2/XD2 Type-H Control Modules are referred to as the Control Module. See Figure 1. The Control Module (1) provides the pneumatic operating functions

More information

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3400V 3500V 3700V

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3400V 3500V 3700V Part B, Section 1 This section covers the following unit configurations. Model Voltage Pump Manifold Control 3100V 3400V 3500V 3700V All Piston (E) 4-Port (A) 6-Port (B or C) 2-Port (S or T) Vista Standard

More information

55-Gallon Powder Drum Truck

55-Gallon Powder Drum Truck Instruction Sheet P/N 0 0 -Gallon Powder Drum Truck for Bulk-Feed Powder Transfer Systems Description See Figure. The -gallon powder drum truck automatically adds bulk powder to a powder coating system

More information

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3700V

Hydraulics. Part B, Section 1. This section covers the following unit configurations. 3700V Part B, Section 1 Model Voltage Pump Manifold Control This section covers the following unit configurations. 3500V 3700V 3860 3890 3930 3960 All Piston (D) 4-Port (A) 6-Port (B or C) 2-Port (S or T) Vista

More information

Module. Section 9. NOTE: This section applies to applicators with CC200 modules B Issued 6/01. Manual 42-CF200-CM-01

Module. Section 9. NOTE: This section applies to applicators with CC200 modules B Issued 6/01. Manual 42-CF200-CM-01 Section 9 NOTE: This section applies to applicators with CC200 modules. 9-0 Table of Contents i Table of Contents Section 9 1. Introduction............................................... 9-1 2. Specifications.............................................

More information

Installing an H-200 Integral Right-Angle Module

Installing an H-200 Integral Right-Angle Module Instruction heet P/N 187 723A Installing an H-200 Integral Right-Angle Module WARNING: Allow only qualified personnel to perform the following tasks. Observe and follow the safety instructions in this

More information

Auto-Flo Air-Assist Automatic Dispensing Valve

Auto-Flo Air-Assist Automatic Dispensing Valve Auto-Flo Air-Assist Automatic Dispensing Valve Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries about its

More information

Auto-Flo Panel Reinforcement Automatic Dispensing Valve

Auto-Flo Panel Reinforcement Automatic Dispensing Valve Auto-Flo Panel Reinforcement Automatic Dispensing Valve Customer Product Manual Part NORDSON CORPORATION AMHERST, OHIO USA Nordson Corporation welcomes requests for information, comments and inquiries

More information

8. Illustrated Parts Lists

8. Illustrated Parts Lists Hydraulics B 1-43 8. Illustrated Parts Lists To order parts, call the Nordson Customer Service Center or your local Nordson representative. Use these five-column parts lists, and the accompanying illustrations,

More information

Manifold-Mounted to Flange-Mounted Solenoid Valve Conversion

Manifold-Mounted to Flange-Mounted Solenoid Valve Conversion Instruction Sheet P/N 106501A03 Manifold-Mounted to Flange-Mounted Solenoid Valve Conversion WARNING: Allow only personnel with appropriate training and experience to operate or service the equipment.

More information

Description. Rhino EFD Bulk Unloader Packages

Description. Rhino EFD Bulk Unloader Packages Rhino EFD Bulk Unloader Packages Description See Figure. The Rhino EFD Pail and -Gallon Drum Bulk Unloader Packages consist of the following major components: Pump () Controls () Frame () Follower Plate

More information

Adjustment. Description. Installation. Rhino SD/XD Pump Overlap Time-Delay Module

Adjustment. Description. Installation. Rhino SD/XD Pump Overlap Time-Delay Module Rhino SD/XD Pump Overlap Time-Delay Module Description See Figure. The Rhino SD/XD Pump Overlap Time-Delay module consists of a pneumatic time-delay valve () that is installed into the drum empty circuit.

More information

Sure Coat Modular Gun Control System Part D: Gun Purge Module. Customer Product Manual Part B

Sure Coat Modular Gun Control System Part D: Gun Purge Module. Customer Product Manual Part B Sure Coat Modular Gun Control System Part D: Gun Purge Module Customer Product Manual Issued 4/0 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 4-919

More information

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an in-out filter.

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an in-out filter. Filter 10-1 Section 10 Filter NOTE: This section applies to applicators with an in-out filter. Table of Contents Filter...................................................... 10-1 Introduction................................................

More information

0 900 psi Pressure-Reducing Diaphragm Regulator

0 900 psi Pressure-Reducing Diaphragm Regulator Instruction Sheet P/N 009506-09 0 900 psi Pressure-Reducing Diaphragm Regulator Description The Nordson 0 900 psi diaphragm regulator reduces high primary pressures to lower secondary pressures. It is

More information

Paint/Solvent/Dump Valve and Flow-Through Valve

Paint/Solvent/Dump Valve and Flow-Through Valve Instruction Sheet P/N 08573D Paint/Solvent/Dump Valve and Flow-Through Valve. Description See Figure. The paint/solvent/dump valve is a normally-closed valve that opens to trigger and/or dump coating material.

More information

Section 8. Parts A Issued 7/00. Manual V -MA -01 (formerly 7-505/6V -MA -01) E 2000 Nordson Corporation All rights reserved

Section 8. Parts A Issued 7/00. Manual V -MA -01 (formerly 7-505/6V -MA -01) E 2000 Nordson Corporation All rights reserved Section 8 E 000 Nordson Corporation 00 497A Manual 47-506V -MA -0 (formerly 7-505/6V -MA -0) 8-0 Manual 47-506V -MA -0 (formerly 7-505/6V -MA -0) 00 497A E 000 Nordson Corporation 8- Section 8. Introduction

More information

Solenoid Valve Installation Kit

Solenoid Valve Installation Kit Instruction Sheet P/N 7 5A Solenoid Valve Installation Kit WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related

More information

0-800 psi Carbide Seat Fluid Pressure Regulator

0-800 psi Carbide Seat Fluid Pressure Regulator Instruction Sheet P/N 0350C 0-800 psi Carbide Seat Fluid Pressure Regulator Description The Nordson 0-800 psi carbide seat fluid pressure regulator is designed for use with general liquid coatings. The

More information

SP30 10:1 Piston Pump

SP30 10:1 Piston Pump Instruction Sheet P/N SP30 10:1 Piston Pump 1. Safety Read this section before using the equipment. This section contains recommendations and practices applicable to the safe installation, operation, and

More information

5000 Gerotor Pump Service Instructions

5000 Gerotor Pump Service Instructions Instruction Sheet P/N 237569B WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction This

More information

8. Illustrated Parts Lists

8. Illustrated Parts Lists Hydraulics B 1-41 8. Illustrated Parts Lists To order parts, call the Nordson Customer Service Center or your local Nordson representative. Use these five-column parts lists, and the accompanying illustrations,

More information

Miniature Soft Seat Fluid Pressure Regulator

Miniature Soft Seat Fluid Pressure Regulator Instruction Sheet P/N 1. Description The Nordson miniature soft seat fluid pressure regulator is designed for use with hydraulic and pneumatic medias. The regulator body and wetted parts are constructed

More information

Series 3000V Low Level Indicator

Series 3000V Low Level Indicator Instruction Sheet P/N 237 473A Series 3000V Low Level Indicator 1. Introduction The low level indicator sends a signal to an external device when the adhesive level in the applicator s tank is low. The

More information

Fluidizing Pickup Tube Kits

Fluidizing Pickup Tube Kits Instruction Sheet P/N 303787-02 Introduction The fluidizing pickup tube kit retrofits your existing mobile powder system with fluidizing air. It injects fluidizing air at the pickup tube inlet with minimal

More information

Rhino VE Follower Modules

Rhino VE Follower Modules Instruction Sheet P/N 08 0 Description See Figure. The follower module attaches onto the hydraulic section of the pump (). It is designed to force material out of straight-sided containers. Follower plate

More information

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with a Universal in-out filter.

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with a Universal in-out filter. Filter 10-1 Section 10 Filter NOTE: This section applies to applicators with a Universal in-out filter. Table of Contents Filter...................................................... 10-1 Introduction................................................

More information

OBSOLETE. RA-16 Rotary Atomizer Upgrade Kit. Instruction Sheet P/N A. 1. Introduction. 2. Disassembly

OBSOLETE. RA-16 Rotary Atomizer Upgrade Kit. Instruction Sheet P/N A. 1. Introduction. 2. Disassembly Instruction Sheet P/N RA-16 Rotary Atomizer Upgrade Kit 1. Introduction This instruction sheet explains the procedure for installing the upgrade kit onto your RA-16 rotary atomizer. 2. Disassembly The

More information

OPERATOR S CARD. Select Series H-400 Hot Melt Dispensing Guns. Safety. Description/Intended Use. Nordson Corporation P/N E

OPERATOR S CARD. Select Series H-400 Hot Melt Dispensing Guns. Safety. Description/Intended Use. Nordson Corporation P/N E Nordson Corporation OPERATOR S CARD P/N 32 96E Select Series H-400 Hot Melt Dispensing Guns Safety WARNING: System pressurized! Relieve system hydraulic pressure before breaking any hydraulic connection

More information

Module. Table of Contents. Section 9. Module NOTE: This section applies to applicators with CF200PAD right-angle modules.

Module. Table of Contents. Section 9. Module NOTE: This section applies to applicators with CF200PAD right-angle modules. 9-1 Section 9 NOTE: This section applies to applicators with CF200PAD right-angle modules. Table of Contents.................................................... 9-1 Introduction................................................

More information

Sure Coat 90 Degree Spray Extension

Sure Coat 90 Degree Spray Extension Instruction Sheet P/N 076A Sure Coat 90 Degree Spray Extension Description The 90 Degree Spray Extension is used on Sure Coat Automatic Powder Spray Guns. It allows powder to be sprayed at right angles

More information

EP-2 Three-Piston Pump

EP-2 Three-Piston Pump EP- Three-Piston Pump Customer Product Manual Issued 0/ For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.

More information

OPERATOR S CARD. Select Series H-440 Hot Melt Dispensing Guns. Safety. Description. Nordson Corporation P/N D

OPERATOR S CARD. Select Series H-440 Hot Melt Dispensing Guns. Safety. Description. Nordson Corporation P/N D Nordson Corporation OPERATOR S CARD P/N 321 198D Select Series H-440 Hot Melt Dispensing Guns Safety WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions

More information

AN-8 Plus Air Spray Gun Solvent-Based to Waterborne Conversion Kit

AN-8 Plus Air Spray Gun Solvent-Based to Waterborne Conversion Kit Instruction Sheet P/N 10874C AN-8 Plus Air Spray Gun Solvent-Based to Waterborne Conversion Kit 1. Description Use the solvent-based to waterborne conversion kit to convert your Nordson AN-8 Plus Air Spray

More information

EP-2 Si Three-Piston Pump

EP-2 Si Three-Piston Pump EP- Si Three-Piston Pump Customer Product Manual Issued 0/ For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.

More information

Description. Rhino SD2/XD2 Follower Modules

Description. Rhino SD2/XD2 Follower Modules Rhino SD/XD Follower Modules Description See Figure. The follower module attaches onto the hydraulic section of the pump (). It is designed to force material out of straight-sided containers. Standard

More information

Description. Rhino SD2/XD2 Follower Modules

Description. Rhino SD2/XD2 Follower Modules Rhino SD/XD Follower Modules Description See Figure. The follower module attaches onto the hydraulic section of the pump (). It is designed to force material out of straight-sided containers. Standard

More information

Spray Pressure Control Manifold

Spray Pressure Control Manifold Instruction Sheet P/N 0870G0 WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction The

More information

Iso-Flo Coupling Repair

Iso-Flo Coupling Repair Instruction Sheet P/N 229782C Iso-Flo Coupling Repair Introduction This instruction sheet covers the repair of the male and female couplings used in the Automatic and Manual Iso-Flo HD Voltage Block Systems,

More information

Spray Pressure Control Manifold

Spray Pressure Control Manifold Instruction Sheet P/N 0870-0 WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction The

More information

Prodigy HDLV Manual System Installation Instructions

Prodigy HDLV Manual System Installation Instructions Prodigy HDLV Manual System Installation Instructions Instruction Sheet P/N 1062384C WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document

More information

11-1 Electrical System NOTE: Table of Contents Electrical System

11-1 Electrical System NOTE: Table of Contents Electrical System Electrical System - Section Electrical System NOTE: This section applies to applicators with Universal C-style cordsets. Table of Contents Electrical System........................................... -

More information

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an out-in filter.

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with an out-in filter. Filter 10-1 Section 10 Filter NOTE: This section applies to applicators with an out-in filter. Table of Contents Filter...................................................... 10-1 Introduction................................................

More information

High-Pressure Fluid Swivel Connectors. Description. Select the Proper Swivel Combination. Specifications. Tube OD (in.) Dash Numbers (JIC-)

High-Pressure Fluid Swivel Connectors. Description. Select the Proper Swivel Combination. Specifications. Tube OD (in.) Dash Numbers (JIC-) High-Pressure Fluid Swivel onnectors escription The figures in this document are for general reference only. High-pressure fluid swivel connectors can be used in a variety of different combinations, and

More information

Hard Seat Fluid Pressure Regulator

Hard Seat Fluid Pressure Regulator Instruction Sheet P/N 04742-02 Description The Nordson hard seat fluid pressure regulator is designed for use with abrasive coatings. The regulator body is constructed of stainless steel with a nickel-plated

More information

0-500 PSI Soft Seat Fluid Pressure Regulator

0-500 PSI Soft Seat Fluid Pressure Regulator Instruction Sheet P/N 0953A Description The Nordson 0-500 psi soft seat fluid pressure regulator is designed for use with nonabrasive liquid coatings. The regulator body is constructed of stainless steel

More information

Soft Seat Fluid Pressure Regulator

Soft Seat Fluid Pressure Regulator Instruction Sheet P/N 04622F Description The Nordson soft seat fluid pressure regulator is designed for use with nonabrasive liquid coatings. The regulator body is constructed of stainless steel with a

More information

Maintenance. Part A, Section 5. This section covers the following unit configurations.

Maintenance. Part A, Section 5. This section covers the following unit configurations. Part A, Section 5 This section covers the following unit configurations. Model 3100V 3400V 3830V 3860V 3890V 3930V Voltage 1, 2 Pump AC Gear (K or L) Manifold 4-Port (J)) Control Vista Standard (V) Vista

More information

Circulation Kits for CP Pumps

Circulation Kits for CP Pumps Instruction Sheet P/N 08000C Description This instruction sheet covers two circulation kits for CP Pumps: Stainless steel circulation kit, with Viton O-rings Stainless steel circulation kit, with EPR O-rings

More information

Standard and Conical AN Series Air Spray Nozzles

Standard and Conical AN Series Air Spray Nozzles Instruction Sheet P/N 107967E Standard and Conical AN Series Air Spray Nozzles Introduction The Nordson air spray nozzles described in this instruction sheet are categorized by their type of spray pattern:

More information

Two Component Meter Cylinder Assembly Replacement

Two Component Meter Cylinder Assembly Replacement Instruction Sheet P/N Two Component Meter Cylinder Assembly Replacement WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other

More information

8. Illustrated Parts Lists

8. Illustrated Parts Lists Hydraulics B 1-45 8. Illustrated Parts Lists To order parts, call the Nordson Customer Service Center or your local Nordson representative. Use these five-column parts lists, and the accompanying illustrations,

More information

RA-20 Paint/Solvent/Dump Valve

RA-20 Paint/Solvent/Dump Valve Instruction Sheet P/N 74B0 RA-0 Paint/Solvent/Dump Valve Description The paint/solvent valve is a normally closed valve used to trigger coating material. The valve may be used alone to actuate paint or

More information

One-Gun Add-On Kit For Smart-Coat Controllers

One-Gun Add-On Kit For Smart-Coat Controllers Instruction Sheet P/N One-Gun Add-On Kit For Smart-Coat Controllers 1. Introduction This document contains procedures for installing a one-gun add-on kit to your Smart-Coat Controller. For additional information,

More information

Electrical System. Table of Contents. Section 11. Electrical System NOTE: This section applies to applicators with C-style cordsets.

Electrical System. Table of Contents. Section 11. Electrical System NOTE: This section applies to applicators with C-style cordsets. Electrical System - Section Electrical System NOTE: This section applies to applicators with C-style cordsets. Table of Contents Electrical System........................................... - Introduction................................................

More information

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with a threaded filter.

Filter. Table of Contents. Section 10. Filter NOTE: This section applies to applicators with a threaded filter. Filter 10-1 Section 10 Filter NOTE: This section applies to applicators with a threaded filter. Table of Contents Filter... 10-1 Introduction... 10-3 Filter Overview... 10-3 Filter Service... 10-4 Relieving

More information

Sure Coat Modular Gun Control System Part B: Pneumatic Modules. Customer Product Manual Part B

Sure Coat Modular Gun Control System Part B: Pneumatic Modules. Customer Product Manual Part B Sure Coat Modular Gun Control System Part B: Pneumatic Modules Customer Product Manual Issued 4/03 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800)

More information

NRPS-100 Rotary Sieve

NRPS-100 Rotary Sieve NRPS-100 Rotary Sieve Customer Product Manual Part For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative.

More information

Electrical System. Table of Contents. Section 11. Electrical System NOTE: This section applies to applicators with M-style cordsets.

Electrical System. Table of Contents. Section 11. Electrical System NOTE: This section applies to applicators with M-style cordsets. Electrical System - Section Electrical System NOTE: This section applies to applicators with M-style cordsets. Table of Contents Electrical System........................................... - Introduction................................................

More information

Prodigy Generation II High-Capacity HDLV Powder Transfer Pump

Prodigy Generation II High-Capacity HDLV Powder Transfer Pump Prodigy Generation II High-Capacity HDLV Powder Transfer Pump Customer Product Manual Issued 0/0 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. This document

More information

Parts. Part B, Section 5. This section covers the following unit configurations Model 3500 Voltage 1. 2 Piston (E,) Issued 11/00

Parts. Part B, Section 5. This section covers the following unit configurations Model 3500 Voltage 1. 2 Piston (E,) Issued 11/00 Part B, Section 5 This section covers the following unit configurations Model 5 Voltage. Pump Piston (E,) Manifold -Port (A) Control UniScan Nordson Corporation Issued / B 5- Issued / 999 Nordson Corporation

More information

Upgrading the Sure Coat Modular Gun Control System

Upgrading the Sure Coat Modular Gun Control System Instruction Sheet P/N 007365B Upgrading the Sure Coat Modular Gun Control System WARNING: Read the Safety section in the Sure Coat Modular Gun Control System manual before performing any of the following

More information

Use and Care Guide.

Use and Care Guide. Model # Part # 53301111 L-40-802-SV-N-BZ 53301112 L-40-802-SV-N-W Use and Care Guide LED OUTDOOR RE LIGHT Questions, problems, missing parts? Call ETi SSL Customer Service 8:30 a.m. 5 p.m., EST, Monday

More information

Back Pressure Regulator

Back Pressure Regulator Instruction Sheet P/N 108652H Description The Nordson back pressure regulator is a spring-loaded, hand-operated fluid pressure regulator designed for use with general liquid coating materials. The regulator

More information

Module. Table of Contents. Section 9. Module NOTE: This section applies to applicators with MB200 modules.

Module. Table of Contents. Section 9. Module NOTE: This section applies to applicators with MB200 modules. 9- Section 9 NOTE: This section applies to applicators with MB200 modules. Table of Contents.................................................... 9- Introduction................................................

More information

Introduction. Pressed Shaft Flowmeter. Flowmeter Service Kits. Disassembly. Idler Shaft Removal

Introduction. Pressed Shaft Flowmeter. Flowmeter Service Kits. Disassembly. Idler Shaft Removal Flowmeter Service Kits Introduction See Figure. This instruction sheet provides repair procedures for flowmeters that use either pressed or screw-in shafts. Refer to the applicable repair procedure: Pressed

More information

Electric Vibratory Box Feeder Retrofit Kit

Electric Vibratory Box Feeder Retrofit Kit Instruction Sheet P/N 008E WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Description This

More information

Series AD-31 Handgun Swivel Connector Replacement Kit P/N and P/N

Series AD-31 Handgun Swivel Connector Replacement Kit P/N and P/N Instruction heet eries AD-31 Handgun wivel Connector Replacement Kit P/N 238 808 and P/N 238 809 1. Description This instruction sheet contains procedures for replacing the swivel connector on eries AD-31

More information

Parts. Part B, Section 5. Model 3500 Voltage 1, 2. Manifold 6-Port (B or C) 2-Port (S or T) Issued 11/00 B5EN-05-[3-PARTS]-6

Parts. Part B, Section 5. Model 3500 Voltage 1, 2. Manifold 6-Port (B or C) 2-Port (S or T) Issued 11/00 B5EN-05-[3-PARTS]-6 Part B, Section 5 Model 500 Voltage, Pump Piston (E) Manifold -Port (B or C) -Port (S or T) Control MultiScan (M) 000Nordson Corporation -000 Issued /00 B 5-0 -000 Issued /00 000 Nordson Corporation B

More information

VL400 Melters. Safety. Introduction. Nordson Corporation OPERATOR S CARD P/N A

VL400 Melters. Safety. Introduction. Nordson Corporation OPERATOR S CARD P/N A Nordson Corporation OPERATOR S CARD P/N 052644A VL400 Melters Safety WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other

More information

Module. Table of Contents. Section 9. Module NOTE: This section applies to applicators with bead or slot modules.

Module. Table of Contents. Section 9. Module NOTE: This section applies to applicators with bead or slot modules. 9-1 Section 9 NOTE: This section applies to applicators with bead or slot modules. Table of Contents... 9-1 Introduction... 9-3 Overview... 9-7 Service... 9-9 Adjusting a ClassicBlue Zero-Cavity... 9-9

More information

High Flow and 100 PLUS FB Powder Pumps

High Flow and 100 PLUS FB Powder Pumps Instruction Sheet P/N 07 987C High Flow and 00 PLUS FB Powder Pumps. Description The Nordson High Flow and 00 PLUS Powder Pumps are highly efficient venturi-type pumps designed primarily for pipe-coating

More information

:,Rhino SD/XD G/D 24 Vdc ISO

:,Rhino SD/XD G/D 24 Vdc ISO :,Rhino SD/XDG/D Vdc ISO ()Rhino SD/XD() SD/XD Rhino SD/XDG/D Vdc ISO Rhino SD/XD, Rhino SD/Xd, (Rhino SD/XD) 006 Nordson Corporation P/N 75606A-0 Rhino SD/XDG/D Vdc ISO 0 9 5 8 7 6 P/N 75606A-0 006 Nordson

More information

Rhino SD/XD Depressurization Modules for Electric Changeover Controls

Rhino SD/XD Depressurization Modules for Electric Changeover Controls Instruction Sheet 1041-04 Rhino SD/XD Depressurization Modules for Electric Changeover Controls Description Rhino SD/XD depressurization modules relieve material pressure by flowing material under the

More information

Prodigy HDLV Generation II Manual System Installation Instructions

Prodigy HDLV Generation II Manual System Installation Instructions Prodigy HDLV Generation II Manual System Installation Instructions Instruction Sheet P/N 1081707A WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions

More information

Mobile Powder Spray System Dolly with Hopper

Mobile Powder Spray System Dolly with Hopper Instruction Sheet P/N 08766H Mobile Powder Spray System Dolly with Hopper WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all

More information

Normally Open H200 and 90_ CF200 Module Seal Rebuild Kit

Normally Open H200 and 90_ CF200 Module Seal Rebuild Kit Instruction Sheet 108 792A Normally Open H200 and 90_ CF200 Module Seal Rebuild Kit 1. Description Use this rebuild kit to service the following modules: S Normally Open H200 (N.O. H200) Module -- P/N

More information

Encore and Spectrum (Global) Powder Feed Center Clamping Cylinder

Encore and Spectrum (Global) Powder Feed Center Clamping Cylinder Instruction Sheet P/N 6480-0 Encore and Spectrum (Global) Powder Feed Center Clamping Cylinder WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in

More information

A7A Single and Dual Automatic Airless Spray Guns

A7A Single and Dual Automatic Airless Spray Guns A7A Single and Dual Automatic Airless Spray Guns Customer Product Manual Issued 8/06 For parts and technical support, call the Finishing Customer Support Center at (800) 433-939. This document is available

More information

Control System. Part B, Section 1. This section covers the following unit configurations. Model Voltage 1, 2 Pump Piston (E, F, or G)

Control System. Part B, Section 1. This section covers the following unit configurations. Model Voltage 1, 2 Pump Piston (E, F, or G) Part B, Section 1 This section covers the following unit configurations. Model 3100 3400 3500 Voltage 1, 2 Pump Piston (E, F, or G) Manifold 4-Port (A) 6-Port (B or C) Control UniScan (1) B 1-0 B 1-1 Section

More information

Rhino SD2/XD2 Electric Container Level Sensors for 125-mm Frames

Rhino SD2/XD2 Electric Container Level Sensors for 125-mm Frames Instruction Sheet P/N 1613207 01 Rhino SD2/XD2 Electric Container Level Sensors for 125-mm Frames Description See Figure 1. The Rhino SD2/XD2 electric container level sensor module uses magnetic sensors

More information

Mobile Powder Spray System Dolly with Hopper for Cable-Fed Systems

Mobile Powder Spray System Dolly with Hopper for Cable-Fed Systems Instruction Sheet P/N Mobile Powder Spray System Dolly with Hopper for Cable-Fed Systems WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document

More information

Low Level Indicator. Part E, Section 1. This section covers the following unit configurations. 3500V 3700V 3800V 3900V E2EN 03 [3V LLI] 4

Low Level Indicator. Part E, Section 1. This section covers the following unit configurations. 3500V 3700V 3800V 3900V E2EN 03 [3V LLI] 4 Part E, Section 1 This section covers the following unit configurations. Model 3400V 3500V 3700V 3800V 3900V Voltage All Pump All Manifold All Control All E 1-0 E 1-1 Section E 1 WARNING: Allow only qualified

More information

Installing the Low Level Indicator (P/N or P/N )

Installing the Low Level Indicator (P/N or P/N ) Instruction Sheet Installing the Low Level Indicator (P/N 276 176 or P/N 276 4) 1. Introduction There are two Low Level indicator kits, one for flat bottomed tanks and one for the new finned tanks. P/N

More information

B Manifold K or O Assembly Parts List. Parts

B Manifold K or O Assembly Parts List. Parts B -0 Parts. Manifold K or O Assembly Parts List The manifold assembly includes the manifold block, manifold filter, pressure relief valve, and drain valve. Depending on the configuration of the melter,

More information

Control. Part B, Section 2. This section covers the following unit configurations. 3400V 3500V. Voltage 4. Pump Piston (E, F, G)

Control. Part B, Section 2. This section covers the following unit configurations. 3400V 3500V. Voltage 4. Pump Piston (E, F, G) Part B, Section 2 Model This section covers the following unit configurations. Voltage 4 3100V 3400V 3500V Pump Piston (E, F, G) Manifold 4-Port (A) 6-Port (B, C) 2-Port (S, T) Vista Standard (V) B 2-0

More information