STUDY OF EFFECTS OF FUEL INJECTION PRESSURE ON PERFORMANCE FOR DIESEL ENGINE AHMAD MUIZZ BIN ISHAK
|
|
- Sandra Wade
- 5 years ago
- Views:
Transcription
1 STUDY OF EFFECTS OF FUEL INJECTION PRESSURE ON PERFORMANCE FOR DIESEL ENGINE AHMAD MUIZZ BIN ISHAK Thesis submitted in fulfilment of the requirements for the award of the Bachelor of Mechanical Engineering with Automotive Engineering Faculty of Mechanical Engineering UNIVERSITY MALAYSIA PAHANG JUN 2012
2 ii SUPERVISOR S DECLARATION I hereby declare that I have checked this project and in my opinion, this project is adequate in terms of scope and quality for the award of the Bachelor of Mechanical Engineering with Automotive Engineering. Signature : Name of Supervisor Position : PROF. DR. ROSLI BIN ABU BAKAR : PROFESSOR OF UNIVERSITY MALAYSIA PAHANG Date : 22 JUNE 2012
3 iii STUDENT S DECLARATION I hereby declare that the work in this project is my own except for quotations and summaries which have been duly acknowledged. The project has not been accepted for any degree and is not concurrently submitted for award of other degree. Signature : Name : AHMAD MUIZZ BIN ISHAK ID Number : MH Date : 22 JUNE 2012
4 vii TABLE OF CONTENTS CONTENTS PAGE SUPERVISOR S DECLARATION STUDENT S DECLARATION ACKNOWLEDGMENT ABSTRACT ABSTRAK TABLE OF CONTENTS LIST OF FIGURES LIST OF SYMBOLS LIST OF GREEK SYMBOLS LIST OF SUBSCRIPTS LIST OF ABBREVIATIONS ii iii iv v vi vii ix x xi xii xii CHAPTER 1 INTRODUCTION 1.1 Project Background Fuel Injection System Problem Statement Project Objectives Project Scopes Flowchart Description Thesis Organization 6 CHAPTER 2 LITERATURE REVIEW 2.1 Introduction Diesel Engine and Fuel Injection System Operation Cycle of Electronic Fuel Injection System Advantages of Fuel Injection System Types of Fuel Injections System 15
5 viii CHAPTER 3 METHODOLOGY 3.1 Introduction Overview of Methodology Simulation Model Simulation Model Flowchart Mathematical Formulation Hypotheses Fluid Container of Known Pressure Pipe Container of Unknown Pressure Flow Passage Valve Laminar Flow 32 CHAPTER 4 RESULT AND DISCUSSION 4.1 Introduction Results and Discussion Pump Side Pressure Nozzle Side Pressure Effect of Pump Speed on Pressure of the Pump Side Effect of Pump Speed on Pressure of the Nozzle Side Effect of Pump Speed on the Injection Rate Effect of Nozzle Opening Pressure on the Injection Rate 40 CHAPTER 5 CONCLUSION AND RECOMMENDATION 5.1 Conclusion Recommendations 42 REFERENCES 43
6 ix LIST OF FIGURES FIG. NO. TITLE PAGE 1.1 Fuel injection system بFlowchart بfinalبfor yearبproject Diesel fuel injection system Simulation model flowchart Elementary units of the mathematical model Simplified model for the injection system Characteristic grid Concentrated vapour cavitation in a pipe node i Laminar flow in the gap between the non-moving piston and the sleeve Pump side pressure Nozzle side pressure Effect of pump speed on pressure of the pump side Effect of pump speed on pressure of the nozzle side Effect of pump speed on the injection rate Effect of nozzle opening pressure on the injection rate 40
7 x LIST OF SYMBOLS SYMBOL DESCRIPTION A pipe inside cross section area, cross-section area of a moving part, controlling area geometric cross-section area of a flow passage polynomial coefficients of speed of pressure pulse polynomial coefficients of diesel oil density speed of pressure pulse in diesel oil, speed of pressure pulse in fluid, d pipe inside diameter, piston diameter f friction factor, viscous damping coefficient spring initial force acceleration due to gravity K bulk modulus of elasticity of fluid, modulus of elasticity k spring rate l gap length molar mass of vapour m moving mass of valve number of volumetric flows entering the container number of moving parts number of volumetric flow exiting the container number of controlling pressures P, pressure total derivative of pressure in relation to time initial pressure pressure before the flow passage pressure after the flow passage density, fluid density, density of homogenous fluid vapour density, density of fluid vapour density of diesel oil at initial pressure volume flow rate
8 xi R Re T t v V x volume flow rate into a node, volumetric flow entering the container volume flow rate out of a node, volumetric flow exiting the container molar gas constant Reynolds number temperature time fluid velocity, velocity of the moving part, valve velocity volume cavitation volume velocity at the inlet point of the flow passage distance along pipe axis, lift of a moving part, valve lift LIST OF GREEK SYMBOLS SYMBOL DESCRIPTION pipe angle to horizontal plane clearance between piston and sleeve relative roughness of the inside surface of the pipe pressure difference between the sleeve ends time step flow coefficient fictive flow coefficient dynamic viscosity of the fluid
9 xii LIST OF SUBSCRIPTS SUBSCRIPT DESCRIPTION c0 c2 cav g in m out v vin vout polynomial coefficients of speed of pressure pulse cavitation volume geometric cross-section area of a flow passage volumetric flows entering the container moving parts volumetric flow exiting the container polynomial coefficients of diesel oil density controlling pressures, vapour, fluid vapour, volume volume flow rate into a node, volumetric flow entering the container volume flow rate out of a node, volumetric flow exiting the container LIST OF ABBREVIATIONS ABBREVIATION DESCRIPTION NO HC CO SO HSDI ECU EFI TBI Nitrogen Monoxide Nitrogen Oxides Hydrocarbon Carbon Monoxide Sulphur Monoxide High Speed Direct Injection Electronic Control Unit Electronic Fuel Injection Throttle Body Injection
COMPUTATIONAL ANALYSIS OF TWO DIMENSIONAL FLOWS ON A CONVERTIBLE CAR ROOF ABDULLAH B. MUHAMAD NAWI
COMPUTATIONAL ANALYSIS OF TWO DIMENSIONAL FLOWS ON A CONVERTIBLE CAR ROOF ABDULLAH B. MUHAMAD NAWI Report submitted in partial of the requirements for the award of the degree of Bachelor of Mechanical
More informationDEVELOPMENT OF COMPRESSED AIR POWERED ENGINE SYSTEM BASED ON SUBARU EA71 MODEL CHEN RUI
DEVELOPMENT OF COMPRESSED AIR POWERED ENGINE SYSTEM BASED ON SUBARU EA71 MODEL CHEN RUI A project report submitted in partial fulfillment of the requirements for the award of the degree of Bachelor of
More informationEXPERIMENT AND ANALYSIS OF MOTORCYCLE EXHAUST DESIGN ABDUL MUIZ BIN JAAFAR
EXPERIMENT AND ANALYSIS OF MOTORCYCLE EXHAUST DESIGN ABDUL MUIZ BIN JAAFAR Report submitted in partial fulfilment of the requirement for the award of the degree of Bachelor of Mechanical Engineering with
More informationANALYSIS OF OVERCURRENT PROTECTION RELAY SETTINGS OF A COMMERCIAL BUILDING NURUL SYAQIRAH BINTI MOHD SUFI UNIVERSITI MALAYSIA PAHANG
ANALYSIS OF OVERCURRENT PROTECTION RELAY SETTINGS OF A COMMERCIAL BUILDING NURUL SYAQIRAH BINTI MOHD SUFI UNIVERSITI MALAYSIA PAHANG ANALYSIS OF OVERCURRENT PROTECTION RELAY SETTINGS OF A COMMERCIAL BUILDING
More informationUNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS
UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: DESIGN IMPROVEMENT FOR POWER WINDOW MECHANISM - SCISSOR TYPE SESI PENGAJIAN: 2009/2010 Saya, BADRUL HISYAM BIN AHMAD (871103-06-5557) mengaku
More informationPREDICTION OF REMAINING USEFUL LIFE OF AN END MILL CUTTER SEOW XIANG YUAN
PREDICTION OF REMAINING USEFUL LIFE OF AN END MILL CUTTER SEOW XIANG YUAN Report submitted in partial fulfillment of the requirements for the award of the degree of Bachelor of Engineering (Hons.) in Manufacturing
More informationENERGY BALANCE STUDY FOR 4 STROKE GASOLINE ENGINE ANALYSES ABDULLAH SHARIFFUDIN MOHAMAD BACHELOR OF MECHANICAL ENGINEERING UNIVERSITI MALAYSIA PAHANG
ENERGY BALANCE STUDY FOR 4 STROKE GASOLINE ENGINE ANALYSES ABDULLAH SHARIFFUDIN MOHAMAD BACHELOR OF MECHANICAL ENGINEERING UNIVERSITI MALAYSIA PAHANG UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS
More informationCOMPARISON OF AUTOMATIC AND CVT TRANSMISSION FOR A CAR UNDER 1 LITER ENGINE
COMPARISON OF AUTOMATIC AND CVT TRANSMISSION FOR A CAR UNDER 1 LITER ENGINE AHMAD MUSTAKIM BIN MOHD RUSLI BACHELOR OF ENGINEERING UNIVERSITI MALAYSIA PAHANG 2010 UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN
More informationTHE ANALYSIS OF WING PERFORMANCE FOR RECONNAISSANCE UAV ZULKIFLI BIN YUSOF UNIVERSITI MALAYSIA PAHANG
THE ANALYSIS OF WING PERFORMANCE FOR RECONNAISSANCE UAV ZULKIFLI BIN YUSOF UNIVERSITI MALAYSIA PAHANG The Analysis of Wing Performance for Reconnaissance UAV ZULKIFLI BIN YUSOF Report submitted in partial
More informationDEVELOPMENT HYDROGEN GAS GENERATOR FOR DUAL FUEL ENGINE USING YULL BROWN METHOD AHMAD ZAKI BIN ZAIMANI UNIVERSITI MALAYSIA PAHANG
DEVELOPMENT HYDROGEN GAS GENERATOR FOR DUAL FUEL ENGINE USING YULL BROWN METHOD AHMAD ZAKI BIN ZAIMANI UNIVERSITI MALAYSIA PAHANG ii UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: DEVELOPMENT
More informationUNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS
UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: DESIGN AND FABRICATE AL-QURAN AND BOOK RACK FOR UMP MOSQUE Saya, AMIR YUSRI MOHD YUSOF SESI PENGAJIAN: 2009/2010 mengaku membenarkan tesis
More informationDESIGN, DETAIL ANALYSIS AND PERFORMANCE TESTING OF UAV PROPULSION SYSTEM CHE MUHAMMAD RIDHWAN BIN CHE HASHIM
DESIGN, DETAIL ANALYSIS AND PERFORMANCE TESTING OF UAV PROPULSION SYSTEM CHE MUHAMMAD RIDHWAN BIN CHE HASHIM Faculty of Mechanical Engineering UNIVERSITI MALAYSIA PAHANG UNIVERSITI MALAYSIA PAHANG BORANG
More informationDESIGN AND ANALYSIS OF THE SOLAR CAR BODY YUSRI BIN YUSOF. Report submitted in partial fulfillment of the requirements
DESIGN AND ANALYSIS OF THE SOLAR CAR BODY YUSRI BIN YUSOF Report submitted in partial fulfillment of the requirements for the award of Diploma in Mechanical Engineering Faculty of Mechanical Engineering
More informationBORANG PENGESAHAN STATUS TESIS
UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: BATTERY LEVEL MONITORING SYSTEM SESI PENGAJIAN: 2011/2012 Saya AIESYAH BINTI GHAZALI (HURUF BESAR) mengaku membenarkan tesis (Sarjana Muda/Sarjana
More informationFINAL PROJECT RESEARCH PAPER
FINAL PROJECT COMPARISON ANALYSIS OF ENGINE PERFOMANCE BETWEEN CONVENTIONAL ENGINE (CARBURETOR) SYSTEM AND ELECTRONIC FUEL INJECTION (EFI) ENGINE SYSTEM OF TOYOTA KIJANG SERIES 7K-E RESEARCH PAPER Submitted
More informationDESIGN AND FABRICATION OF A PALM KERNEL CRACKING MACHINE DIKEOCHA NKIRUKA OLIVE EM DEPARTMENT OF MECHANICAL ENGINEERING
DESIGN AND FABRICATION OF A PALM KERNEL CRACKING MACHINE ;. BY DIKEOCHA NKIRUKA OLIVE 2006124481EM DEPARTMENT OF MECHANICAL ENGINEERING SCHOOL OF ENGINEERING AND ENGINEERING TECHNOLOGY FEDERAL UNIVERSITY
More informationDIRECT TORQUE CONTROL OF A THREE PHASE INDUCTION MOTOR USING HYBRID CONTROLLER. RAJESHWARI JADI (Reg.No: M070105EE)
DIRECT TORQUE CONTROL OF A THREE PHASE INDUCTION MOTOR USING HYBRID CONTROLLER A THESIS Submitted by RAJESHWARI JADI (Reg.No: M070105EE) In partial fulfillment for the award of the Degree of MASTER OF
More informationDESIGN OF COMPRESSED NATURAL GAS MIXER USING COMPUTATIONAL FLUID DYNAMICS. D. Ramasamy, S. Mahendran, K. Kadirgama and M. M. Noor
National Conference in Mechanical Engineering Research and Postgraduate Students (1 st NCMER 2010) 26-27 MAY 2010, FKM Conference Hall, UMP, Kuantan, Pahang, Malaysia; pp. 614-620 ISBN: 978-967-5080-9501
More informationDEVELOPMENT OF MICROHYDRO GENERATOR SYSTEM AHMAD ZUBAIDI BIN ABDUL MD RANI UNIVERSITI MALAYSIA PAHANG
DEVELOPMENT OF MICROHYDRO GENERATOR SYSTEM AHMAD ZUBAIDI BIN ABDUL AZIZ @ MD RANI UNIVERSITI MALAYSIA PAHANG UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: Saya DEVELOPMENT OF MICROHYDRO
More informationUNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS
UNIVERSITI MALAYSIA PAHANG BORANG PENGESAHAN STATUS TESIS JUDUL: DESIGN AND DEVELOPMENT OF 1-SEATED URBAN CAR CHASSIS USING ALUMINIUM SESI PENGAJIAN: 2010/2011 Saya, FAZLIANA BINTI FAUZUN (880216-01-5438)
More informationFischer-Tropsch Refining
Fischer-Tropsch Refining by Arno de Klerk A thesis submitted in partial fulfillment of the requirements for the degree Philosophiae Doctor (Chemical Engineering) in the Department of Chemical Engineering
More informationPREDICTION STUDIES FOR THE PERFORMANCE OF A SINGLE CYLINDER HIGH SPEED SI LINEAR ENGINE MOHD NORDIN BIN ZAZALLI
iii PREDICTION STUDIES FOR THE PERFORMANCE OF A SINGLE CYLINDER HIGH SPEED SI LINEAR ENGINE MOHD NORDIN BIN ZAZALLI A report submitted in partial fulfillment of the requirements for the award of the degree
More informationFoundations of Thermodynamics and Chemistry. 1 Introduction Preface Model-Building Simulation... 5 References...
Contents Part I Foundations of Thermodynamics and Chemistry 1 Introduction... 3 1.1 Preface.... 3 1.2 Model-Building... 3 1.3 Simulation... 5 References..... 8 2 Reciprocating Engines... 9 2.1 Energy Conversion...
More informationPOTENTIALITY OF INTRODUCING ABSORPTION CHILLER SYSTEMS TO IMPROVE THE DIESEL POWER PLANT PERFORMANCE IN SRI LANKA A
POTENTIALITY OF INTRODUCING ABSORPTION CHILLER SYSTEMS TO IMPROVE THE DIESEL POWER PLANT PERFORMANCE IN SRI LANKA MTN Albert Master of Engineering 118351A Department of Mechanical Engineering University
More informationOptimal Design and Analysis of Hybrid Energy Systems
Yarmouk University Hijjawi Faculty for Engineering Technology Department of Electrical Power Engineering Optimal Design and Analysis of Hybrid Energy Systems (HES) for Some Study Cases in Jordan A Thesis
More informationEFFECT OF SOME PROCESS VARIABLES ON THE PRODUCTION OF BIODIESEL FROM CASTOR OIL JERRY OGHENEVO EYA WONOWE
]'7757 EFFECT OF SOME PROCESS VARIABLES ON THE PRODUCTION OF BIODIESEL FROM CASTOR OIL BY JERRY OGHENEVO EYA WONOWE 2004/18494EH DEPARTMENT OF CHEMICAL ENGINEERING FEDERAL UNIVERSITY OF TECHNOLOGY MINNA,
More informationMODELING AND SIMULATION OF MODIFIED SKYHOOK CONTROLLER FOR ACTIVE SUSPENSION SYSTEM MUHAMAD RUSYDI BIN ALI
MODELING AND SIMULATION OF MODIFIED SKYHOOK CONTROLLER FOR ACTIVE SUSPENSION SYSTEM MUHAMAD RUSYDI BIN ALI A report submitted in partial fulfillment of the requirements for the award of the degree of Bachelor
More informationINNOVATION AND DEVELOPMENT OF A HIGH PRESSURE WATER NOZZLE DISCHARGED WITH CURTAIN SPRAY FOR OIL LEAKAGE IN OFFSHORE MUHAMMAD NADZIR BIN NORDIN
INNOVATION AND DEVELOPMENT OF A HIGH PRESSURE WATER NOZZLE DISCHARGED WITH CURTAIN SPRAY FOR OIL LEAKAGE IN OFFSHORE MUHAMMAD NADZIR BIN NORDIN Report submitted in partial fulfillment of the requirements
More informationDESIGN AND FABRICATION OF POLYVINYL CHLORIDE TIE-ROD CYLINDER FOR LOW PRESSURE WATER HYDRAULIC SYSTEM
DESIGN AND FABRICATION OF POLYVINYL CHLORIDE TIE-ROD CYLINDER FOR LOW PRESSURE WATER HYDRAULIC SYSTEM TEO CHUN EARN UNIVERSITI TEKNIKAL MALAYSIA MELAKA i SUPERVISOR DECLARATION I hereby declare that I
More informationState Legislation, Regulation or Document Reference. Civil Aviation Rule (CAR) ; Civil Aviation Rules (CAR) Part 21. Appendix C.
Annex or Recommended Practice Definition INTERNATIONAL STANDARDS AND RECOMMENDED PRACTICES PART I. DEFINITIONS AND SYMBOLS Civil Aviation Rule (CAR) 91.807; Civil Aviation Rules (CAR) Part 21 The s of
More informationDESIGN AND FAllRlCATION OF DUAL OPERATED PALM-FRUIT. DIGESTING lviachine
DESIGN AND FAllRlCATION OF DUAL OPERATED PALM-FRUIT DIGESTING lviachine BY ",., ALADE RIDWAN ADENIYI MA TRIC No. 2005/23545EA I,. DEPARTMENT OF AGRICUL1~ URAL & BIORESOURCES ENGINEERING FEDERAL UNIVERSITY
More informationLead Acid Batteries Modeling and Performance Analysis of BESS in Distributed Generation
Murdoch University Faculty of Science & Engineering Lead Acid Batteries Modeling and Performance Analysis of BESS in Distributed Generation Heng Teng Cheng (30471774) Supervisor: Dr. Gregory Crebbin 11/19/2012
More informationCFD analysis of triple concentric tube heat exchanger
Available online at www.ganpatuniversity.ac.in University Journal of Research ISSN (Online) 0000 0000, ISSN (Print) 0000 0000 CFD analysis of triple concentric tube heat exchanger Patel Dharmik A a, V.
More informationThis item is protected by original copyright
THE INVESTIGATION OF HYBRID SYSTEM WITH AC TURBINE GENERATOR AND PHOTOVOLTAIC MOHD HAKIMI BIN WAHAT SCHOOL OF ELECTRICAL SYSTEM ENGINEERING UNIVERSITI MALAYSIA PERLIS 2011 THE INVESTIGATION OF HYBRID SYSTEM
More informationRESEARCH PROJECT REPORT
RESEARCH PROJECT REPORT MODELING OF LIQUID FUEL PRODUCTION VIA CATALYTIC CRACKING OF PALM OIL USING MCM-41 AS CATALYST PROPOSED BY: HENGKY KURNIAWAN IVAN YARED 5203004011 5203004023 DEPARTMENT OF CHEMICAL
More informationSPRAY SIMULATION OF HYDROGEN FUEL FOR SPARK IGNITION ENGINE USING COMPUTATIONAL FLUID DYNAMIC (CFD)
SPRAY SIMULATION OF HYDROGEN FUEL FOR SPARK IGNITION ENGINE USING COMPUTATIONAL FLUID DYNAMIC (CFD) ABDUL RAHMAN BIN MOHD SABRI BACHELOR OF ENGINEERING UNIVERSITI MALAYSIA PAHANG 2010 ABDUL RAHMAN BIN
More informationScroll Compressor Oil Pump Analysis
IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Scroll Compressor Oil Pump Analysis To cite this article: S Branch 2015 IOP Conf. Ser.: Mater. Sci. Eng. 90 012033 View the article
More informationMODELING AND SIMULATION OF A HYBRID ELECTRIC VEHICLE SYSTEM
MODELING AND SIMULATION OF A HYBRID ELECTRIC VEHICLE SYSTEM by Eng. Hala Shaban Mohamed Khalil Electronics Research Institute A Thesis Submitted To The Faculty of Engineering at Cairo University In Partial
More informationMaster of Engineering
STUDIES OF FAULT CURRENT LIMITERS FOR POWER SYSTEMS PROTECTION A Project Report Submitted in partial fulfilment of the requirements for the Degree of Master of Engineering In INFORMATION AND TELECOMMUNICATION
More informationCFD Flow Analysis and Optimization of Exhaust Muffler
CFD Flow Analysis and Optimization of Exhaust Muffler Saumil Mahesh Trivedi 1, Sangita Bansode 2, Pankaj Pawar 3 1 Mtech CAD-CAM & Robotics Student Somaiya college of engineering 2 Professor, Department
More informationFluid Power with Applications
Fluid Power with Applications Sixth Edition Anthony Esposito Professor Emeritus Department of Manufacturing Engineering Miami University Oxford, Ohio Prentice Hall Upper Saddle River, New Jersey Columbus,
More informationEffect of Helix Parameter Modification on Flow Characteristics of CIDI Diesel Engine Helical Intake Port
Effect of Helix Parameter Modification on Flow Characteristics of CIDI Diesel Engine Helical Intake Port Kunjan Sanadhya, N. P. Gokhale, B.S. Deshmukh, M.N. Kumar, D.B. Hulwan Kirloskar Oil Engines Ltd.,
More informationMODEL UPDATING FOR FUN KART CHASSIS MOHD SAHRIL BIN MOHD FOUZI UNIVERSITI MALAYSIA PAHANG
MODEL UPDATING FOR FUN KART CHASSIS MOHD SAHRIL BIN MOHD FOUZI UNIVERSITI MALAYSIA PAHANG MODEL UPDATING FOR FUN KART CHASSIS MOHD SAHRIL BIN MOHD FOUZI A report submitted in partial fulfillment of the
More informationEFFECT OF EXHAUST TEMPERATURE ON THE PERFORMANCE OF A DIESEL ENGINE WITH EGR
EFFECT OF EXHAUST TEMPERATURE ON THE PERFORMANCE OF A DIESEL ENGINE WITH EGR NAVINDRAN AlL. SUBRAMANIAM Report submitted in partial fulfillment of the requirements For the award of Bachelor of Mechanical
More informationCONTENTS Duct Jet Propulsion / Rocket Propulsion / Applications of Rocket Propulsion / 15 References / 25
CONTENTS PREFACE xi 1 Classification 1.1. Duct Jet Propulsion / 2 1.2. Rocket Propulsion / 4 1.3. Applications of Rocket Propulsion / 15 References / 25 2 Definitions and Fundamentals 2.1. Definition /
More informationImpacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics
Impacts of Short Tube Orifice Flow and Geometrical Parameters on Flow Discharge Coefficient Characteristics M. Metwally Lecturer, Ph.D., MTC, Cairo, Egypt Abstract Modern offset printing machine, paper
More informationDESIGN AND OPTIMIZATION OF HTV FUEL TANK ASSEMBLY BY FINITE ELEMENT ANALYSIS
DESIGN AND OPTIMIZATION OF HTV FUEL TANK ASSEMBLY BY FINITE ELEMENT ANALYSIS GAJENDRA G 1, PRAKASHA A M 2, DR NOOR AHMED R 3, DR.K.S.BADRINARAYAN 4 1PG Scholar, Mechanical department, M S Engineering College,
More informationDEVELOPMENT OF AUTO RE-CLOSER EARTH LEAKAGE CIRCUIT BREAKER (AR-ELCB) AHMAD KHAIRUL AZWAN BIN JANTAN ANUA JAH
DEVELOPMENT OF AUTO RE-CLOSER EARTH LEAKAGE CIRCUIT BREAKER (AR-ELCB) AHMAD KHAIRUL AZWAN BIN JANTAN ANUA JAH A thesis submitted in fulfillment of the requirements for the award of the degree of Bachelor
More informationIntroduction to Particulate Emissions 1. Gasoline Engine Particulate Emissions Introduction 3. References 7 About the Authors 8
contents SECTION 1 Introduction to Particulate Emissions 1 CHAPTER 1 Gasoline Engine Particulate Emissions Introduction 3 References 7 About the Authors 8 CHAPTER 2 Health Impact of Particulates from Gasoline
More informationFINITE ELEMENT ANALYSIS OF AUTOMOTIVE INTAKE MANIFOLD USING CAE SOFTWARE MUHAMMAD HAIKAL BIN HARON
FINITE ELEMENT ANALYSIS OF AUTOMOTIVE INTAKE MANIFOLD USING CAE SOFTWARE MUHAMMAD HAIKAL BIN HARON A report submitted in partial fulfilment of the requirements for the award of the degree of Bachelor of
More informationSimulation of Pressure Variation in Hydraulic circuit with & without Hydraulic Accumulator in MATLAB-Simhydraulics
Simulation of Pressure Variation in Hydraulic circuit with & without Hydraulic Accumulator in MATLAB-Simhydraulics Cherian Johny 1, Dr.K.RSivadas 2 1 PG Student, Department. of Mechanical Engineering,
More informationESTIMATION OF VEHICLE KILOMETERS TRAVELLED IN SRI LANKA. Darshika Anojani Samarakoon Jayasekera
ESTIMATION OF VEHICLE KILOMETERS TRAVELLED IN SRI LANKA Darshika Anojani Samarakoon Jayasekera (108610J) Degree of Master of Engineering in Highway & Traffic Engineering Department of Civil Engineering
More informationPRELIMINARY DESIGN OF PRECIPITATED SILICA PLANT FROM SULPHURIC ACID AND SODIUM SILICATE WITH CAPACITY OF 45,000 TON/ YEAR
PRELIMINARY DESIGN OF PRECIPITATED SILICA PLANT FROM SULPHURIC ACID AND SODIUM SILICATE WITH CAPACITY OF 45,000 TON/ YEAR By: Linda Fatmawati D500112005 Supervisor: Dr. Ir. Ahmad M. Fuadi, MT Kun Harismah
More informationFlow Computation of Total Head Losses and Total Pressure Losses in a Typical Gasoline Fuel Injector System
International Academic Institute for Science and Technology International Academic Journal of Science and Engineering Vol. 3, No. 10, 2016, pp. 30-47. ISSN 2454-3896 International Academic Journal of Science
More informationKINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD
Jurnal Mekanikal June 2014, No 37, 16-25 KINEMATICAL SUSPENSION OPTIMIZATION USING DESIGN OF EXPERIMENT METHOD Mohd Awaluddin A Rahman and Afandi Dzakaria Faculty of Mechanical Engineering, Universiti
More informationResearch in hydraulic brake components and operational factors influencing the hysteresis losses
Research in hydraulic brake components and operational factors influencing the hysteresis losses Shreyash Balapure, Shashank James, Prof.Abhijit Getem ¹Student, B.E. Mechanical, GHRCE Nagpur, India, ¹Student,
More informationDesign and Modeling of Fluid Power Systems ME 597/ABE 591
Systems ME 597/ABE 591 Dr. Monika Ivantysynova MAHA Professor Flud Power Systems MAHA Fluid Power Research Center Purdue University Systems Dr. Monika Ivantysynova, Maha Professor Fluid Power Systems Mivantys@purdue.edu
More informationModal analysis of Truck Chassis Frame IJSER
Modal analysis of Truck Chassis Frame 158 Shubham Bhise 1, Vaibhav Dabhade 1, Sujit Pagi 1, Apurvi Veldandi 1. 1 B.E. Student, Dept. of Automobile Engineering, Saraswati College of Engineering, Navi Mumbai,
More informationDesign and Analysis of a Two-Stage Anti-Tank Missile
Design and Analysis of a Two-Stage Anti-Tank Missile by David Qi Zhang A Project Submitted to the Graduate Faculty of Rensselaer Polytechnic Institute in Partial Fulfillment of the Requirements for the
More informationAppendix A.1 Calculations of Engine Exhaust Gas Composition...9
Foreword...xi Acknowledgments...xiii Introduction... xv Chapter 1 Engine Emissions...1 1.1 Characteristics of Engine Exhaust Gas...1 1.1.1 Major Components of Engine Exhaust Gas...1 1.1.2 Units Used for
More informationDesign of Self-Adjusting Strainer Assembly for Off-road Conditions used in Diesel Engine
Design of Self-Adjusting Strainer Assembly for Off-road Conditions used in Diesel Engine #1 Aditya C. Zod, #2 Dr. A. B. Kanase-Patil 1 PG Student, Department of Mechanical Engineering, Sinhgad College
More informationAnalysis. Techniques for. Racecar Data. Acquisition, Second Edition. By Jorge Segers INTERNATIONAL, Warrendale, Pennsylvania, USA
Analysis Techniques for Racecar Data Acquisition, Second Edition By Jorge Segers INTERNATIONAL, Warrendale, Pennsylvania, USA Preface to the Second Edition xiii Preface to the First Edition xv Acknowledgments
More informationEffect of Varying Load on Performance and Emission of C.I. Engine Using WPO Diesel Blend
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 2 Ver. V (Mar - Apr. 2015), PP 37-44 www.iosrjournals.org Effect of Varying Load on Performance
More informationDiagnostics of Rotor and Stator Problems in Industrial Induction Motors
Diagnostics of Rotor and Stator Problems in Industrial Induction Motors by Fang Duan B.E. (Telecommunication Engineering), Southwest Jiaotong University, China, 2005 Thesis submitted for the degree of
More informationSMART SUN TRACKING WITH AUTOMATED CLEANING SYSTEM FOR PV MODULES AMIRAH AFIQAH BINTI AHMED
SMART SUN TRACKING WITH AUTOMATED CLEANING SYSTEM FOR PV MODULES AMIRAH AFIQAH BINTI AHMED This thesis is submitted as partial fulfillment of the requirements for the award of the Bachelor of Electrical
More informationCOMPRESSIBLE FLOW ANALYSIS IN A CLUTCH PISTON CHAMBER
COMPRESSIBLE FLOW ANALYSIS IN A CLUTCH PISTON CHAMBER Masaru SHIMADA*, Hideharu YAMAMOTO* * Hardware System Development Department, R&D Division JATCO Ltd 7-1, Imaizumi, Fuji City, Shizuoka, 417-8585 Japan
More informationMack T-11 D EGR Engine Oil Test. Report Packet Version No. Conducted For
Report Packet Version No. Conducted For V = I = N = Valid; The reference oil/non-reference oil was evaluated in accordance with the test procedure. Invalid; The reference oil/non-reference oil was not
More informationSTUDIES AND DESIGN OF SUSPENSION SYSTEM FOR A FORMULA SAE RACING CAR AIZAT FUAD BIN AHMAD SHATAR UNIVERSITI TEKNIKAL MALAYSIA MELAKA
STUDIES AND DESIGN OF SUSPENSION SYSTEM FOR A FORMULA SAE RACING CAR AIZAT FUAD BIN AHMAD SHATAR UNIVERSITI TEKNIKAL MALAYSIA MELAKA STUDIES AND DESIGN OF SUSPENSION SYSTEM FOR A FORMULA SAE RACING CAR
More informationABSTRACT I. INTRODUCTION III. GEOMETRIC MODELING II. LITERATURE REVIW
2017 IJSRSET Volume 3 Issue 5 Print ISSN: 2395-1990 Online ISSN : 2394-4099 Themed Section: Engineering and Technology Performance Analysis of Helical Coil Heat Exchanger Using Numerical Technique Abhishek
More informationCKING OF NAPHTHA TO PRODUCE BENZENE, TOLUENE AND XYLENE (BTX)
CKING OF NAPHTHA TO PRODUCE BENZENE, TOLUENE AND XYLENE (BTX) By AFOLAYAN ATINUKE ADEOLA 2006/24163EH DEPARTMENT OF CHEMICAL ENGINEERING, FEDERAL;UNIVE~SITY OF TECHNOLOGY, MINNA, NIGERIA NOVEMBER,.2011
More informationRESOLUTION MEPC.198(62) Adopted on 15 July GUIDELINES ADDRESSING ADDITIONAL ASPECTS TO THE NOx TECHNICAL CODE 2008 WITH REGARD TO
ANNEX 6 MEPC 62/24 Annex 6, page 1 2011 GUIDELINES ADDRESSING ADDITIONAL ASPECTS TO THE NO x TECHNICAL THE MARINE ENVIRONMENT PROTECTION COMMITTEE, RECALLING Article 38(a) of the Convention on the International
More informationMODAL ANALYSIS TEST RIG FOR CLAMPED-CLAMPED BOUNDRY CONDITION MOHD HAFIZ BIN RAZILAH
MODAL ANALYSIS TEST RIG FOR CLAMPED-CLAMPED BOUNDRY CONDITION MOHD HAFIZ BIN RAZILAH Report submitted in partial fulfillment of the requirements for the award of the Diploma of Mechanical Engineering Faculty
More informationDETERMINATION OF AERODYNAMIC DRAG FORCE ACTING ON MOVING HEAVY DUTY TRUCK-TRAILER IN MALAYSIA MOHAMAD HAFIZ BIN MOHAMAD
i DETERMINATION OF AERODYNAMIC DRAG FORCE ACTING ON MOVING HEAVY DUTY TRUCK-TRAILER IN MALAYSIA MOHAMAD HAFIZ BIN MOHAMAD This report is presented in Partial fulfillment of the requirements for the Degree
More informationCOMPARISON OF STANDARD EXHAUST AND RACING EXHAUST ON MACHINE PERFORMANCE
FINAL PROJECT COMPARISON OF STANDARD EXHAUST AND RACING EXHAUST ON MACHINE PERFORMANCE Arranged by: BONDAN SENOAJI PRAKOSA D200102007 MECHANICAL ENGINEERING DEPARTMENT INTERNATIONAL PROGRAM IN AUTOMOTIVE/MOTORCYCLE
More informationSignature of the candidate. The above candidate has carried out research for the Masters Dissertation under my supervision.
DECLARATION I declare that this is my own work and this dissertation does not incorporate without acknowledgement any material previously submitted for a Degree or Diploma in any other University or institute
More informationGEAR RATIO INVESTIGATION OF AUTOMOTIVE MANUAL TRANSMISSION MUHAMAD AMIR SHAH ARIF HARUN. A thesis submitted in partial fulfillment of the
GEAR RATIO INVESTIGATION OF AUTOMOTIVE MANUAL TRANSMISSION MUHAMAD AMIR SHAH ARIF HARUN A thesis submitted in partial fulfillment of the requirement for the award of the Diploma of Mechanical Engineering
More informationDesign Analysis and Optimization of Disc Brake
Design Analysis and Optimization of Disc Brake Assembly of A 4- Wheeler Race C ar Avijit Singh Gangwar B.E. Automobile Engineer Manipal Institute Of Technology Abstract-A disc brake is a wheel brake which
More informationTHERMAL STRESS ANALYSIS OF HEAVY TRUCK BRAKE DISC ROTOR
Thermal Stress Analysis of heavy Truck Brake Disc Rotor THERMAL STRESS ANALYSIS OF HEAVY TRUCK BRAKE DISC ROTOR M.Z. Akop 1, R. Kien 2, M.R. Mansor 3, M.A. Mohd Rosli 4 1, 2, 3, 4 Faculty of Mechanical
More informationManufacturer: Address: ZIP Code: City: Country: VAT #: Signatory, Name: Signatory, Title: Phone: Fax: WWW: Head of Engineering:
CERTIFICATION APPLICATION Reciprocating internal combustion engines Certificate No.: EX Exhaust emission measurement - Part 1: Test-bed measurement of gaseous and particulate exhaust emissions Ref.: ISO
More informationFinite Element Analysis on Thermal Effect of the Vehicle Engine
Proceedings of MUCEET2009 Malaysian Technical Universities Conference on Engineering and Technology June 20~22, 2009, MS Garden, Kuantan, Pahang, Malaysia Finite Element Analysis on Thermal Effect of the
More information2. Write the expression for estimation of the natural frequency of free torsional vibration of a shaft. (N/D 15)
ME 6505 DYNAMICS OF MACHINES Fifth Semester Mechanical Engineering (Regulations 2013) Unit III PART A 1. Write the mathematical expression for a free vibration system with viscous damping. (N/D 15) Viscous
More informationTRAFFIC SIMULATION IN REGIONAL MODELING: APPLICATION TO THE INTERSTATEE INFRASTRUCTURE NEAR THE TOLEDO SEA PORT
MICHIGAN OHIO UNIVERSITY TRANSPORTATION CENTER Alternate energy and system mobility to stimulate economic development. Report No: MIOH UTC TS41p1-2 2012-Final TRAFFIC SIMULATION IN REGIONAL MODELING: APPLICATION
More informationEffectiveness of Oil Consumption at Motoring Test Case Study: Automotive Company
TECHNICAL UNIVERSITY OF MALAYSIA MALACCA Effectiveness of Oil Consumption at Motoring Test Case Study: Automotive Company Thesis submitted in accordance with the requirements of the National Technical
More informationCharging Electric Vehicles in the Hanover Region: Toolbased Scenario Analyses. Bachelorarbeit
Charging Electric Vehicles in the Hanover Region: Toolbased Scenario Analyses Bachelorarbeit zur Erlangung des akademischen Grades Bachelor of Science (B. Sc.) im Studiengang Wirtschaftsingenieur der Fakultät
More informationSemi-Active Suspension for an Automobile
Semi-Active Suspension for an Automobile Pavan Kumar.G 1 Mechanical Engineering PESIT Bangalore, India M. Sambasiva Rao 2 Mechanical Engineering PESIT Bangalore, India Abstract Handling characteristics
More informationACTUAL CYCLE. Actual engine cycle
1 ACTUAL CYCLE Actual engine cycle Introduction 2 Ideal Gas Cycle (Air Standard Cycle) Idealized processes Idealize working Fluid Fuel-Air Cycle Idealized Processes Accurate Working Fluid Model Actual
More informationARC FLASH ANALYSIS STUDY IN INDUSTRY HARNA A/P ELAVARASU
ARC FLASH ANALYSIS STUDY IN INDUSTRY HARNA A/P ELAVARASU Report submitted in partial fulfillment of the requirements For the award of the degree of Bachelor of Electrical Engineering with Power System
More informationDESIGN AND DEVELOPMENT A SMALL STIRLING ENGINE NURUL HUDA BINTI BASO
DESIGN AND DEVELOPMENT A SMALL STIRLING ENGINE NURUL HUDA BINTI BASO A report submitted in fulfillment of the requirements for the award of Bachelor of Mechanical Engineering. Faculty of Mechanical Engineering
More informationPROGRESS IN QUALITY ASSESSMENT OF CONVEYOR IDLERS
PROGRESS IN QUALITY ASSESSMENT OF CONVEYOR IDLERS W. Bartelmus and W. Sawicki Wroc³aw University of Technology Faculty of Mining Machinery Systems Division Wroc³aw Poland Abstract: The paper deals with
More informationWP5 - Computational Mechanics B5 - Temporary Vertical Concrete Safety Barrier MAIN REPORT Volume 1 of 1
ROBUST PROJECT TRL Limited WP5 - Computational Mechanics B5 - Temporary Vertical Concrete Safety Barrier MAIN REPORT Volume 1 of 1 December 2005 Doc. No.: ROBUST-5-010c Rev. 0. (Logo here) Main Report
More informationALKALI AND RARE EARTH METALS LOADING ON DEOILED-SPENT BLEACHING CLAY AS CATALYSTS IN TRANSESTERIFICATION OF WASTE OILS
ALKALI AND RARE EARTH METALS LOADING ON DEOILED-SPENT BLEACHING CLAY AS CATALYSTS IN TRANSESTERIFICATION OF WASTE OILS REHAN BINTI ZAINOL ABIDIN Master of Science UNIVERSITI MALAYSIA PAHANG SUPERVISOR
More informationFABRICATION OF HYBRID ELECTRIC CHOPPER TYPE MOTORCYCLE FRONT SUSPENSION MUHAMMAD AMIR AKMAL BIN AHAMAD KHALID
FABRICATION OF HYBRID ELECTRIC CHOPPER TYPE MOTORCYCLE FRONT SUSPENSION MUHAMMAD AMIR AKMAL BIN AHAMAD KHALID Report submitted in partial fulfilment of the requirements for the award of Diploma in Mechanical
More informationManual for Assessing Safety Hardware
American Association of State Highway and Transportation Officials Manual for Assessing Safety Hardware 2009 vii PREFACE Effective traffic barrier systems, end treatments, crash cushions, breakaway devices,
More informationCOMPARISON OF THE LEAKAGE CHARACTERISTICS OF THE STRAIGHT ANNULAR AND CONVERGENT SEALS. A Thesis SERAFETTIN USTUN
COMPARISON OF THE LEAKAGE CHARACTERISTICS OF THE STRAIGHT ANNULAR AND CONVERGENT SEALS A Thesis by SERAFETTIN USTUN Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment
More informationThis thesis is proposed to fulfill a part of conferment condition for
SUSPENSION GEOMETRY ANALYSIS OF FORMULA VARSITY RACE CAR AMRUL BIN OMAR This thesis is proposed to fulfill a part of conferment condition for Bachelor Mechanical Engineering (Automotive) Faculty of Mechanical
More informationTHE ANALYSIS OF THE FORCES THAT ACT ON THE MOTORCYCLE BRAKE PEDAL DURING EMERGENCY BRAKE
THE ANALYSIS OF THE FORCES THAT ACT ON THE MOTORCYCLE BRAKE PEDAL DURING EMERGENCY BRAKE SUTHAN A/L ERIN UNIVERSITI TEKNIKAL MALAYSIA MELAKA THE ANALYSIS OF THE FORCES THAT ACT ON THE MOTORCYCLE BRAKE
More informationCOMPARISON OF DIFFERENT SOFTWARE PACKAGES IN POWER FLOW AND SHORT-CIRCUIT SIMULATION STUDIES. A Project
COMPARISON OF DIFFERENT SOFTWARE PACKAGES IN POWER FLOW AND SHORT-CIRCUIT SIMULATION STUDIES A Project Presented to the faculty of the Department of Electrical and Electronic Engineering California State
More informationContent. Chapter 1 Hydraulic energy converters... 10
Content Chapter 1 Hydraulic energy converters... 10 1.1 List of symbols... 13 1.2 Hydraulic pump types, constant output... 14 1.2.1 External gear pumps... 16 1.2.2 Internal gear pumps... 17 1.2.3 Vane
More informationPI CONTROLLER FOR BATTERY CHARGER SYSTEM MOHD AZHAR BIN AZMI
PI CONTROLLER FOR BATTERY CHARGER SYSTEM MOHD AZHAR BIN AZMI This thesis is submitted as partial fulfillment of the requirements for the award of Bachelor of Electrical Engineering (Hons.) (Electronics)
More informationInternational Journal of Engineering Research and General Science Volume 5, Issue 3, May-June, 2017 ISSN
HEAT TRANSFER AND FLUID FLOW ANALYSIS OF CIRCULAR RECEIVER TUBE OF SOLAR COLLECTOR Swati Patel 1, M.A.Kadam 2 1 P.G. Student, Department of Mechanical Engineering, Bharati Vidyapeeth Deemed University,
More information