The enginewithintegrated water cooling

Transcription

1 1500 RPM 400/230 V 50 Hz Type IDGPC 45JD 45 /36 kva/kw (PRP) 49.5 /39.6 kva/kw (LTP) The enginewithintegrated water cooling 45kVA/36kW Johndeere diesel engine generator with ISO and CE certificate Engine: Alternator: Engine 4045DF158 Stamford single Bearing with Insulation Class H Generator Supply Scope: Engine, alternator, radiator, auto control panel. Base frame, base fuel tank,flexible pipes, flange, exhaust silencer. Battery, battery charger, battery wires, internal cables, circuit breaker. Manual books of engine, alternator, genset, control panel, wires diagram. Johndeere : 4045DF158 Displacement: 4.5 dm 3 Cylinder quantity :4 Cylinder Fuel consumption: 223g/kw.h Cooling Method: Water-cooled Air intake way: Turbocharged Fuel Tank capacity: 50 L Governor method: Electrical Governor Alternator Bearing: Single Insulation Class: H Phase: 3 Phase/Single Phase Protection Degree: IP 23 Excitation way: Brushless excitationing Stamford Benefits Low noise emission, cost savings as no noise attenation measures are required. Long service intervals: 1,000 hour oil change intervals and low fuel consumption bring savings in operating costs. Low installation costs. Low noise emission, cost savings as no noise attenation measures are required. Combined oil cooling and lubrication prevents corrosion and cavitation. High reliability and durability together with reduced maintenance requirement and wear parts. 1 -

2 Standby Power Standby Power is the nominal engine power available at varying load factors for up to 500 hours per year. This rating conforms to ISO "limited time running power(ltp)". The calculated generator set rating range for standby applications is based on minimum engine power (normal -5%) to provide 100% meet-or-exceed performance for assembled standby generator sets. Prime Power prime power is the nominal power an engine is capable of delivering with a variable load for an unlimited number of hours per year. This rating conforms to ISO "Prime power (PRP)". Key Features Efficient water cooled John Deere diesel engine. Single bearing CGT Stamford alternator Radiator with pressure cap and drain point Fully guarded engine-driven fan Fully welded steel skid base with fork lift pockets Integral fuel tank with filler cap and gauge Heavy duty rubber anti-vibration mountings 12V starter battery and connecting cables Separate engine-driven battery charging alternator Spin on oil and fuel filters and dry type air filter element Industrial silencer (15dBA reduction) supplied loose Key Start control system with analogue instruments Main line circuit breaker Factory Test Certificate Operation & Maintenance Manual Wide range of optional extra features available 2

3 General Data Model 4045DF158 Number of Cylinder 4 Bore x stroke mm In 106x x5 Displacement dm 3 In Compression ratio 17.6:1 Valves per Cylinder intake/exhaust 1/1 Firing order Combustion system Direct Injection Engine type In-line, 4 cycle Aspiration Natural Engine Crankcase Vent system Open Engine Crankcase Pressure kpa In. H 2O Physical Data Length mm in Width mm in Height mm in Weight, dry Kg lb Center of Gravity Location From Rear Face of block (X-axis) mm in Right of Crankshaft (Y-axis) mm in Above Crankshaft (Z-axis) mm in Electrical Data Recommended Battery Capacity (CCA) 12 Volt System Amp Volt system Amp 570 Maximum Allowable starting circuit 12 Volt System Ohm Volt System Ohm Starter Rolling current -12 volt system At 0 C(32 F) Amp 780 At -30 C(-22 F) Amp 1000 Starter Rolling current -24 Volt system At 0 C(32 F) Amp 600 At -30 C(-22 F) Amp 700 Air System Maximum Allowable Rise Ambient Air to Engine Inlet C F 8 15 Maximum Air Intake Restriction Dirty Air Cleaner kpa In. H 2O Clean Air Cleaner kpa In. H 2O 3 12 Engine Air Flow m 3 /min m 3 /min Recommended Intake Pipe Dia mm/in Exhaust System Exhaust flow

4 Prime (PRP) m 3 /min ft 3 /min Standby(LTP) m 3 /min ft 3 /min Exhaust Temperature Prime (PRP) C F Standby(LTP) C F Max Allow Back Pressure kpa(in. H 2O) Recommended Exhaust pipe Dia mm in Cooling System Thermostart start to open C F Power unit Coolant Capacity L qt Minimum air to Boil Temperature C F Fuel System Fuel Injection Pump Stanadyne Governor Regulation 5% Governor Type Mechanical Total Fuel Flow Prime (PRP) kg/h lb/h Standby(LTP) kg/h lb/h Maximum Fuel Transfer Pump Suction m ft Fuel liter Micron Efficiency 8 Lubrication System Oil Pressure at Rated Speed kpa psi Oil Pressure at Low idle kpa psi In Pan Oil Temperature C F Total Engine Oil Capacity with liters L qt Engine Angularity Limits (Continuous) Any Direction -degrees 20

5 Performance Data Gross Rated Power (without fan) kw hp Rated Speed kw hp rpm 1500 Low Idle Speed rpm No BMEP Friction Rated speed Altitude Capability kpa psi kpa psi kw hp m ft Air: Fuel Ratio Noise 1 m 1 m 18.6:1 18.3: Greenpower AB Helsingborgsvägen Varalöv Ängelholm Tel: Fax: info@greenpower.se web: