Class Notes on Thermal Energy Conversion System

Size: px
Start display at page:

Download "Class Notes on Thermal Energy Conversion System"

Transcription

1 Class Notes on Thermal Energy Conversion System For the students of Civil & Rural 3 rd semester Ramesh Khanal Assistant Professorr Nepal Engineering College Bhaktapur, Nepal 2015

2 Course Structure MEC 209.3: Thermal Energy Conversion System (3-1-2) Theory Practical Total Sessional Final Total Course Objective The objective of this course is to make the students familiar with air standard cycles, principle and systems of internal combustion engines and fuels and their combustion properties. Course Contents: 1. Gas Power Cycles and Reversibility (6 hours) Introduction; Air Standard Efficiency of a Cycle; Thermodynamic Reversibility; Carnot s Cycle; Otto Cycle and actual pv diagram for Otto Cycle; Diesel Cycle and actual pv diagram for Diesel Cycle; Dual Combustion Cycle; Comparison of Otto, Diesel and Dual Combustion Cycles; Brayton Cycle; Stirling Cycle. 2. Reciprocating Steam Engine: (5 hours) The Rankine Cycle; Comparison of Rankine and Carnot s Cycle; Rankine Cycle applied to steam engine plant; Rankine Cycle on TS diagram; Steam Engine Indicators; Hypothetical and Actual Indicator Diagram of Steam Engine. 3. Internal Combustion Engines (7 hours) Introduction; Classification of Internal Combustion Engines; Working Cycles of Internal Combustion Engines; Two Stroke Cycle Petrol and Diesel Engines; Four Stroke Cycle Petrol and Diesel Engines; Basic Parameters of Internal Combustion Engines; Components of Internal Combustion Engines. 4. Performance of Internal Combustion Engines (12 hours) Indicated Power, Brake Power, Mean Effective Pressure; Engine Efficiency; Heat Balance for Internal Combustion Engines; Power, Torque, Speed Relationship; Specific Fuel Consumption; Gasoline and Gaseous Fuel Systems: carburation system, temperature and altitude effects, gaseous fuel storage, air-mixing, relative efficiency; Ignition Systems: spark ignition engines, conventional system- primary and secondary circuits, electronic ignition, comparison and effects on engine performance, compression ignition engines, fuel injector characteristics, engine output and efficiency; Cooling Systems: liquid (water/anti-freeze) coolant, dry and wet liners corrosion inhibitors, air cooling, temperature limitations, fan power requirement, comparative advantage of liquid and air cooling system; Lubrication i

3 System: lubrication requirements of spark ignition and compression ignition engines, low pressure splash lubrication system, high pressure gear pumps and distribution system. 5. Reciprocating Air Compressor (8 hours) Primary Components of a Reciprocating Air Compressor; Reciprocating Compression, Clearance Volume Effects, p-v diagram and work done; Volumetric and Adiabatic Efficiencies, Compression Process on T-s Diagram; Multi-stage compression, Intercooling, Optimum pressure distribution Work done, Representation of p-v and T-s diagram; Positive Displacement Compressor Types, Axial flow compressors, Roots Blower, Rotary compressors. 6. Fuels and Combustion (7 hours) Introduction; Classification of Fuels; Solid Fuels; Liquid Fuels; Gaseous Fuels; Calorific and Heating Values of Fuels; Determination of Calorific Values for Solid, Liquid and Gaseous Fuels; Combustion Equations for Hydrocarbon Fuels; Combustion in Spark Ignition and Compression Ignition Engines; Pre-Ignition and Ignition Delays; Detonation and Effects of Operating Variables on Detonation. Total Lectures 45 hours Laboratories: Five laboratory Exercises to be performed in this course, as stated hereunder: i. Studies on Parallel Flow and Counter Flow Heat Exchangers ii. iii. iv. Performance Evaluation of Reciprocating Air-Compressor Study of Systems and Components of Internal Combustion Engines Performance Testing of Spark Ignition Engine: Ignition Timing, Fuel Combustion, Losses, Mechanical Efficiency, Air-Fuel Ratio, Volumetric Efficiency, Compression Ratio, Exhaust Emission, Energy Balance v. Performance Testing of Compression Ignition Engine: BMEP, Injection Timing, Fuel Consumption, Losses, Mechanical Efficiency, Air-Fuel Ratio, Volumetric Efficiency, Compression Ratio, Exhaust Emission, Energy Balance Tutorial: Problem Solving and Assignments Text Books and References: i. J.B. Heywood. Internal Combustion Engine Fundamentals. McGraw Hill Book Co. ii. iii. C.R. Ferguson. Internal Combustion Engine. Wiley Publishers (latest edition). P.L. Ballaney. Thermal Engineering (Heat Engines). Khanna Publishers, New Delhi. ii

4 Content Chapter 1. Gas Power Cycles and Reversibility Introduction Air standard efficiency of a cycle Thermodynamic reversibility Carnot cycle Brief introduction to petrol and diesel engine operation Approximation of real cycle with air standard cycle Otto cycle Diesel cycle Dual cycle Comparison of Otto, Diesel and Dual cycle Brayton cycle Stirling Cycle Chapter 2. Reciprocating Steam Engine Rankine cycle Mean temperature of heat addition Comparison of Rankine and Carnot cycle Effect of pressure and temperature on Rankine cycle Working principle of reciprocating steam engine Steam engine indicators Hypothetical indicator diagram Hypothetical and actual indicator diagram Chapter 3. Internal Combustion Engine Introduction Classification of IC engines Working cycle of IC engines Valve timing diagram of four stroke IC engine Components of IC engines Parts common to SI engine Parts common to CI engine Basic engine parameters Chapter 4. Performance of Internal Combustion Engine Mean effective pressure (MEP) Indicated power (IP) iii

5 4.3 Brake power (BP) Engine efficiencies Heat balance for IC engine Torque-power-speed relationship Gasoline and gaseous fuel system Ignition system Engine cooling system Advantage of liquid cooling Disadvantage of liquid cooling Advantage of air cooling Disadvantage of air cooling Engine lubricating system Chapter 5. Reciprocating air compressor Reciprocating compression Work done in compressor Isothermal compression Effect of polytropic index on work required Compression process in T-s diagram Clearance volume effects, P-v diagram and work done Work done in single stage compressor with clearance volume Volumetric and adiabatic efficiencies Effect of delivery pressure on the performance of air compressor Multi-stage compression Representation of P-v and T-s diagram Optimum pressure distribution work done Positive displacement compressor Chapter 6. Fuels and Combustion Introduction Classification of fuels Calorific and heating values of fuels Determination of caloric values Combustion equation for hydrocarbon fuels Combustion in SI and CI engine Abnormal combustion in SI engine Abnormal combustion in CI engine iv

6 v

7 Chapter 1. Gas Power Cycles and Reversibility 1.1 Introduction In the study of thermodynamics, a cycle is defined as a set of processes involving transfer of heat and work. The cycle starts from one state and after completion of set of processes return back to the initial state. The cycle is capable of continuing same process repeatedly. If the purpose of the cycle is to receive heat from surrounding and transfer work to the surrounding, it is called power cycle. We also know that some kind of medium is required for a cycle to transfer heat and work. If a device that operates in thermodynamics power cycle uses gas as working medium then it is called gas power cycle. We also know that according to the second law of thermodynamics, heat can be converted into work and while doing so some part of heat received from the source must be rejected to the surrounding. The difference in heat received from source and heat rejected to surrounding is work done by the cycle to the surrounding. Generally, four processes are required to complete a gas power cycle and they are: a. Compression of gas b. Head addition from source c. Expansion of gas d. Heat rejection to the surrounding 1.2 Air standard efficiency of a cycle We know that air is freely and abundantly available in our atmosphere. For this reason air is commonly used as working medium in gas power cycle. Though the composition of air in some power cycle may change during the cycle (fuel is burned in presence of air in petrol engine and diesel engine), working medium is always treated as ideal gas. All powerproducing engines such as petrol engine, diesel engine, gas turbine; which use air as working medium are approximated as air standard cycle for analysis. One of the parameters used to measure the performance of a power cycle is thermal efficiency. Thermal efficiency of power cycle working with air is also known as air standard efficiency. From the second law of thermodynamics, we know that efficiency of a power cycle can be expressed as, = h Eq. 1.1 Let us consider that qin amount of heat is supplied to an air standard cycle to produce wout amount of work and in the process qout amount heat is rejected. wout = qin qout Eq. 1.2 So, the equation of air standard efficiency of a cycle can be written as 1

8 = = 1 Eq. 1.3 Air standard efficiency of a cycle is an ideal efficiency and no real cycle can have higher efficiency than air standard efficiency. 1.3 Thermodynamic reversibility Thermodynamics reversibility of a process is defined as the capability of the process to return back to original state without changing the condition of either system or surrounding. Factors causing irreversibility in a process: a. Friction b. Free expansion c. Heat transfer through a finite temperature difference d. Mixing of two different substances 1.4 Carnot cycle We know that the efficiency of a heat engine is always less than 100%. Then there should be an engine that is most efficient among all others. For an engine to be most efficient, all the processes forming the cycle must be reversible. The engine which works on cycle with reversible compression, reversible heat addition, reversible expansion and reversible heat rejection is the most efficient. For the heat transfer (either addition or rejection) to be reversible it should be carried out across infinitesimally small temperature difference or at constant temperature. Therefore, reversible heat transfer is possible in isothermal process. For the expansion/compression process, it should be reversible adiabatic or isentropic process. Therefore, the most efficient reversible cycle has the following four processes a. Reversible isothermal heat addition from high temperature source b. Reversible adiabatic (isentropic) expansion c. Reversible isotheral heat rejection to low temperature sink d. Reversible adiabatic compression The cycle which operates based on above four processes is called Carnot cycle. Carnot cycle is a heat engine cycle which operates between the given high-temperature and lowtemperature reservoirs such that every process is reversible. If every process is reversible, the cycle is also reversible. This cycle was proposed by a French engineer Leonard Sadi Carnot ( ). 2

9 1.4.1 Assumptions for Carnot cycle For the reversibility of the processes following assumptions are made 1. No friction is involved. 2. The transfer of heat does not affect the temperature of source or sink. 3. Compression and expansion are reversible. 4. Perfectly reversible adiabatic conditions are achieved. Fig. 1-1 Cylinder arrangement for Carnot Cycle Process 1-2 It is a reversible isothermal process in which heat is transferred from the high-temperature reservoir at constant temperature (T1 or TH). The source at a high temperature is brought in contact with the bottom of the cylinder so that air expands isothermally from V1 to V2. For an isothermal process: V2 V2 Q 1 2 = PV 1 1 ln( ) = mrt1 ln( ) = mrt1 ln( rc ) V V 1 1 Fig. 1-2 P-v and T-s diagram of Carnot Cycle Process 2-3 It is a reversible adiabatic expansion process in which the temperature of the air decreases from T1 to T2. The source is removed and the bottom of the cylinder is insulated so that the air is allowed to expand adiabatically. The volume increases from V2 to V3. Q 2 3 = 0 3

10 Process 3-4 It is a reversible isothermal process in which heat is rejected to the low temperature reservoir at T2. The bottom of the cylinder is brought in contact with the sink at temperature T2 so that air is compressed isothermally from V3 to V4. Process 4-1 V4 V4 Q 3 4 = P3V 3 ln( ) = mrt3 ln( ) = mrt3 ln( rc ) V V 3 It is a reversible adiabatic process in which temperature of working fluid is increased from T1 to T2 by compressing it reversibly and adiabatically. The sink is removed and the bottom of the cylinder is insulated so that the air is allowed to compress adiabatically so that the volume decreases from V4 to V1. Now, NetWork Done= = Q 1 2 Q And, the efficiency of a Carnot cycle is: Work done η = Heat Supplied mrln( rc )( T1 T3 ) = mrt ln( r ) T1 T = T 1 T = 1 T Q 4 1 = Net Heat Supplied 0 = mrt1 ln( r ) mrt3 ln( c c r c ) 3 = 1 Eq Brief introduction to petrol and diesel engine operation 1 In petrol engine, mixture of air and petrol is enters into the cylinder through the inlet valve in intake stroke. In compression stroke, inlet valve is closed and air fuel mixture is compressed inside the cylinder. At the end of the compression, the fuel is burned with the help of spark plug. Because of high pressure after the combustion of fuel, the burned gases expand inside the cylinder. In exhaust stroke, exhaust valve opens and all the burned gases escape outside the cylinder. In this way the cycle is repeated. 1 Detail description of operation principle of petrol and diesel engine is given in chapter 3 4

11 Fig. 1-3 Working mechanism of IC engine In a diesel engine, only air is drawn inside the cylinder and fuel is burned by spraying diesel over the compressed air. The method of compression and expansion and exhaust of diesel engine are similar to that of petrol engine. 1.6 Approximation of real cycle with air standard cycle The cycle that undergoes inside the cylinder of petrol and diesel engine is very complex. To make the analysis of the engine cycle easier, real cycle is approximated with ideal air standard cycle. Petrol engine cycle is approximated with air standard Otto cycle and diesel engine cycle is approximated with air standard Diesel cycle. The difference and approximation in ideal and real cycles are: 1. The gas mixture in the cylinder is treated as air for the entire cycle, and property values of air are used in the analysis. In real cycle, fuel is mixed with air (in SI engine) in first part of cycle. In second part of the cycle the fuel is burned in presence of air and the composition of gas then after is of mixture of mostly N2, CO2 and H2O. As the fraction of fuel is very less compared to air and mixture of N2, CO2 and H2O can be approximated as air, approximation with air does not result large errors. 2. The real open cycle is changed into a closed cycle by assuming that the gases being exhausted are fed back into the intake system. This works with ideal air standard cycles, as both intake gases and exhaust gases are air. Closing the cycle simplifies the analysis. 3. The combustion process is replaced with a heat addition term Qin of equal energy value. 4. The open exhaust process, which carries a large amount of enthalpy out of the system, is replaced with a closed system heat rejection process Qout of equal energy value. 5. The almost-constant-pressure intake and exhaust strokes are assumed to be constant pressure. 6. Compression strokes and expansion strokes are approximated by isentropic processes. To be truly isentropic would require these strokes to be reversible and adiabatic. There 5

12 is some friction between the piston and cylinder walls but, because the surfaces are highly polished and lubricated, this friction is kept to a minimum and the processes are close to frictionless and reversible. 7. The combustion process is idealized by a constant-volume process (petrol cycle), a constant-pressure process (diesel cycle), or a combination of both (CI Dual cycle). 8. Exhaust blow down is approximated by a constant-volume process. 1.7 Otto cycle Working cycle of petrol engine is approximated with Otto cycle, which is described by four processes. Process 1-2: isentropic compression: Fuel-air mixture is taken into the cylinder through suction and the mixture inside the cylinder is compressed until the piston reaches the Top Dead Center (TDC). This process is reversible and adiabatic. The pressure and temperature of the air increase. Process 2-3: constant volume heat addition: The compressed air-fuel mixture is burned with a spark which makes the pressure and temperature of the combustion gases to rise. This process is assumed to occur at constant volume. Process 3-4: isentropic expansion: The piston begins to move until it reaches Bottom Dead Center (BDC) so the expansion of gas occurs adiabatically and reversibly. This process generates work output and the pressure and temperature of air decreases consequently. Process 4-1: constant volume heat rejection: The exhaust valve opens and the pressure and temperature of gas decreases at constant volume. Then the gas is removed from the cylinder by movement of piston and the cycle is completed. Above processes can be shown in P-v and T-s diagram as in Fig Fig. 1-4 P-v and T-s diagram of Otto Cycle 6

13 7 The thermal efficiency of the cycle is given as: = = = = ) ( ) ( T T T T T T T T mc T T mc Q Q Q Q Q V V H L H L H η Since process 1-2 and 3-4 are isentropic, we can write, ( ) = = γ γ r V V T T Where, = 2 1 V V r is called compression ratio And, T T V V V V T T = = = γ γ So, ( ) = η = γ r T T = 1 1 Eq. 1.5 Mean Effective Pressure (mep) is defined as the pressure that, if it acted on the piston during the entire power stroke, would do an amount of work equal to that actually done on the piston. i.e. = Eq. 1.6

14 The Fig. 1-4 represents the idealized or theoretical P-v diagram of petrol engine but the actual P-v diagram of petrol engine closely resembles to the diagram shown in Fig Fig. 1-5 Actual P-v diagram for Petrol Engine 1.8 Diesel cycle Working cycle of diesel engine can be theoretically approximated with diesel cycle which is completed by four processes. Process 1-2: isentropic compression: Air is taken into the cylinder through suction and air inside the cylinder is compressed until the piston reaches the Top Dead Center (TDC). This process is reversible and adiabatic. The pressure and temperature of the air increase. Fig. 1-6 P-v and T-s diagram of Diesel Cycle Process 2-3: constant pressure heat addition: Fuel is injected in the cylinder so that compressed air and fuel is burned spontaneously which makes the pressure and 8

15 temperature of the combustion gases to rise. Simultaneously, the piston moves maintaining the pressure inside the cylinder. This process is assumed to occur at constant pressure. Process 3-4 isentropic expansion: The piston begins to move until it reaches Bottom Dead Center (BDC) so the expansion of gas occurs adiabatically and reversibly. This process generates work output and the pressure and temperature of air decreases consequently. Process 4-1 constant volume heat rejection: The exhaust valve opens and the pressure and temperature of gas decreases at constant volume. Then the gas is removed from the cylinder by movement of piston and the cycle is completed. All the four processes can be shown in P-v and T-s diagram as in Fig. 1-6 The thermal efficiency of diesel cycle is given by, η = W Q H QH Q = Q =1 H Q Q L H mc = 1 mc V P L ( T ( T 4 3 T1 ) T ) 2 = 1 Eq. 1.7 For a Diesel cycle, Compression Ratio, V r = V 1 2 Cut-off Ratio, i.e. V ρ = V 3 2 = = = Eq. 1.8 For isentropic process 1-2 as shown in Fig. 1-6 = Similarly for isobaric process 2-3 = = Eq

16 = = = Substituting the value of T2 from Eq. 1.9 = Eq Process 3-4 is isentropic expansion, = = From Eq. 1.8 and Eq = = Eq Now, from Eq. 1.7, Eq. 1.9, Eq and Eq = 1 = Eq The Fig. 1-6 represents the idealized or theoretical P-v diagram of petrol engine but the actual P-v diagram of petrol engine closely resembles to the diagram shown in Fig Fig. 1-7 Actual P-v diagram for Diesel Engine 10

17 1.9 Dual cycle The dual cycle (limited pressure cycle) is the ideal cycle for modern Compression Ignition (CI) engines. The dual cycle differs from Otto cycle and Diesel cycle, in that heat is supplied at both constant volume and constant pressure. There are five processes involved in dual cycle which are explained with the help of P-v and T-s diagram as shown. Process 1-2: isentropic compression: Air is taken into the cylinder through suction and air inside the cylinder is compressed until the piston reaches the Top Dead Center (TDC). This process is reversible and adiabatic. The pressure and temperature of the air increase. Process 2-3: constant volume heat addition: Fuel is injected in the cylinder before the piston reaches the TDC during compression stroke so some of the combustion occurs at almost constant volume at TDC as in Otto cycle. Process 3-4: constant pressure heat addition: The fuel is continued to be injected at TDC so the combustion continues and the piston moves maintaining the pressure inside the cylinder. This process is assumed to occur at constant pressure. Process 4-5: isentropic expansion: The piston begins to move until it reaches Bottom Dead Center (BDC) so the expansion of gas occurs adiabatically and reversibly. This process generates work output and the pressure and temperature of air decreases consequently. Process 5-1: constant volume heat rejection: The exhaust valve opens and the pressure and temperature of gas decreases at constant volume. Then the gas is removed from the cylinder by movement of piston and the cycle is completed. All the processes involved in theoretical dual cycle can be represented in P-v and T-s diagram as shown in Fig Fig. 1-8 P-v and T-s diagram of Dual Cycle Some parameters used in dual cycle based on the P-v and T-s diagram Heat added at constant volume during process 2-3 (Qin1) = mcv(t3 T2) 11

18 Heat added at constant pressure (during process 3-4) (Qin2) = mcp(t4 T3) Total heat added per cycle (Qin)= mcv(t3 T2) + mcp(t4 T3) Heat rejected at constant volume during process 5-1 (Qout) = mcv(t5 T1) Compression ratio (rc) = v1/v2 Cut-off ratio (ρ) = v4/v3 Pressure ratio (rp) = P3/P2 Now air standard thermal efficiency of the dual cycle is = = 1 h = = 1 + = 1 + Eq Process 1-2: Isentropic compression of air = = = = Eq Process 2-3: Constant volume heat addition = = = = Eq Process 3-4: Constant pressure heat addition = = = = = Eq Process 4-5: Isentropic expansion of air 12

19 = = = = = = = = Eq Now from Eq. 1.13, Eq. 1.14, Eq. 1.15, Eq and Eq = = Eq The actual P-v diagram of modern diesel engine something like as shown in Fig Fig. 1-9 Actual P-v diagram of modern Diesel engine 1.10 Comparison of Otto, Diesel and Dual cycle The important factors, which are used as the basis for comparison of different cycles are compression ratio, peak pressure, heat addition, heat rejection and the net work. In order to compare the performance of the Otto, Diesel and Dual combustion cycles, some of the variable factors must be fixed. In this section, a comparison of these three cycles is made for the same compression ratio, same heat addition, constant maximum pressure and temperature, same heat rejection and net work output. This analysis will show which cycle is more efficient for a given set of operating conditions. We know that efficiency of any heat engine can be expressed as 13

20 = 1 Eq Same compression ratio and heat addition Otto cycle 1-2-2a dual cycle Diesel cycle Fig Same compression ratio and heat addition The P-v and T-s diagram of Otto cycle , the Diesel cycle and the dual cycle 1-2-2a are shown in the Fig In P-v diagram, v1 and v2 is same for all cycles which means the compression ratio is same for all. The T-s diagram is plotted in such a way that area under the curve 2-3 (for Otto cycle), curve 2-2a-3 (for dual cycle) and 2-3 (for diesel cycle) is same. We also know that area under the curve in T-s diagram indicates the heat transfer. So heat addition (qin) is same for all cycles. Again from T-s diagram, it is clear that, Area under curve 4-1 < Area under the curve 4-1 < Area under the curve 4-1 i.e. (qout)otto < (qout)dual < (qout)diesel So with the help of Eq. 1.19, it can be concluded that ηotto > ηdual > ηdiesel for same compression ratio and same heat addition Same compression ratio and heat rejection Otto cycle 1-2-2a dual cycle Diesel cycle Fig Same compression ratio and heat rejection 14

21 As in the previous case, compression ratio is same for all three cycles (Fig. 1-11). The cycle in T-s diagram is drawn in such a way that heat rejection (area under the cure 4-1) is same for the all cycles. From the T-s diagram it is also clear that (qin)otto > (qin)dual > (qin)diesel (area under the curve 2-3 for Otto cycle, area under the curve 2-2a-3 for dual cycle and area under the curve 2-3 for Diesel cycle in T-s diagram) So for same compression ratio and heat rejection. ηotto > ηdual > ηdiesel Same peak temperature, peak pressure and heat rejection Otto cycle a dual cycle Diesel cycle Fig Same peak temperature and peak pressure From the Fig. 1-12, it is clear that peak pressure (P3) is same for each cycle. Similarly same heat rejection (area under curve 4-1) is also same for all cycles. But, (qin)diesel > (qin)dual > (qin)otto (Area under the cure 2-3 for diesel, area under the curve 2-2a-3 for dual and area under the curve 2-3 for otto in T-s diagram) So, ηdiesel > ηdual > ηotto 15

22 Same peak pressure and heat addition Otto cycle a dual cycle Diesel cycle Fig For same peak pressure and heat addition For the same peak pressure (P3) and same heat addition (area under the curve 2-3 for diesel, 2-2a-3 for dual and 2-3 for otto) (qout)diesel < (qout)dual < (qout)otto (area under the curve 4-1 for diesel, 4-1 for dual and 4-1 for otto in T-s diagram) So, for same peak pressure and heat addition ηdiesel > ηdual > ηotto Same maximum pressure and work output Otto cycle a dual cycle Diesel cycle Fig Same maximum pressure and work output We know that, = = Eq For same maximum pressure (P3) and same work output (same area of the cycle Otto, a dual, Diesel in either of T-s and P-v diagram) (qout)diesel < (qout)dual < (qout)otto 16

23 (area under the curve 4-1 for diesel, 4-1 for dual and 4-1 for otto in T-s diagram) So, from the Eq. 1.20, for same peak pressure and work output ηdiesel > ηdual > ηotto 1.11 Brayton cycle The Brayton Cycle, also called the Joule Cycle, was developed originally for use in a piston engine with fuel injection. This cycle is the ideal cycle for the simple gas turbine. The air standard Brayton cycle is composed of constant pressure heat transfer processes separated by isentropic expansion and compression processes. a. Closed Brayton Cycle b. Open Brayton Cycle Fig Closed and open Brayton Cycle The closed-cycle Brayton engine is shown in Fig. 1-15a. The working fluid air enters the compressor in state 1, where it is compressed isentropically until state 2 is reached and enters high temperature heat exchanger. In the heat exchanger heat will be added to the fluid at constant pressure until state 3 is reached. Now high temperature air enters the turbine, where an isentropic expansion occurs, producing mechanical work. The working fluid (air) leaves the turbine at state 4 and enters low temperature heat exchanger, where heat will be rejected from the fluid until state 1 is reached. After completing a cycle previous processes will be repeated in same order. Compression in compressor and expansion in turbine are assumed to be isentropic processes in the ideal closed cycle air standard Brayton cycle. It is easier to construct compressor and turbine which operates nearly adiabatic. However, it is difficult to approach reversibility. The P-v and T-s diagram of closed Brayton cycle can be represented as in Fig

24 18 Fig P-v and T-s diagram of Brayton Cycle The efficiency of Brayton cycle is given by, ) ( ) ( T T mc T T mc Q Q P P H L B = = η 1) ( 1) ( = T T T T T T B η Here, process 2-3 and 4-1 are constant pressure process so P2 = P3 and P1 = P4 For isentropic process 1-2, γ γ = P P T T For isentropic process 3-4, So, T T T T = Eq Now, using Eq the equation of efficiency can be written as γ γ η = = = P P T T T T B

25 1 ηb = 1 1 γ ( r ) γ p Eq Where, P r p = P 2 3 = is the pressure ratio 1 P P Effect of isentropic efficiency of pump and turbine In the previous section, we have assumed the turbine and pump are isentropic. But, in real case, they cannot be isentropic. If isentropic efficiency of turbine and pump are considered, the P-v and T-s diagram of Brayton cycle will be as shown in the Fig In the figure, the cycle is the ideal cycle and the cycle is for non-isentropic turbine and pump. Fig Isentropic efficiency of turbine and pump The head addition in the cycle occurs at process 2-3 while heat rejection occurs at 4-1 process. The turbine efficiency can be defined as = = h h h h = Eq Similarly the pump efficiency can be defined as = = h h h h = Eq The equation for efficiency of the cycle can be written as = 1 19

26 = 1 = 1 Eq Stirling Cycle Ideal Stirling cycle consists of two isothermal and two constant volume processes as follow Fig P-v and T-s diagram of Stirling cycle Stirling Cycle Processes: a) The air is compressed isothermally from state 1 to 2. b) The air at state-2 is passed into the regenerator from the top at a temperature T1. The air passing through the regenerator matrix gets heated from TL to TH. c) The air at state-3 expands isothermally in the cylinder until it reaches state-4. d) The air coming out of the engine at temperature TH (condition 4) enters into regenerator from the bottom and gets cooled while passing through the regenerator matrix at constant volume and it comes out at a temperature TL, at condition 1 and the cycle is repeated. e) It can be shown that the heat absorbed by the air from the regenerator matrix during the process 2-3 is equal to the heat given by the air to the regenerator matrix during the process 4-1, then the exchange of heat with external source will be only during the isothermal processes. So we can write net work done as = For isothermal heat addition during process 3-4 = ln For isothermal heat rejection during process

27 = ln So thermal efficiency of the cycle is = = 1 = 1 ln ln = 1 Eq

28 Solved Numerical Problems 1. In a Carnot cycle, the maximum pressure and temperature are limited to 18 bar and 410 C. The ratio of isentropic compression is 6 and isothermal expansion is 1.5. Assuming the volume of the air at the beginning of isothermal expansion as 0.18 m 3, determine: a. The temperature and pressure at main points in the cycle b. Change in entropy during isothermal expansion c. Mean thermal efficiency of the cycle d. Mean effective pressure of the cycle e. Theoretical power if there are 210 working cycles per minute. Maximum pressure (P2) = 18 bar Maximum temperature (T2) = = 683 K V1/V2 = 6 V3/V2 = 1.5 V2 = 0.18 m 3 a. Temperature and pressure at main points Process 1-2 is isentropic = = = =. = = = =. Process 2-3 is isothermal = = = = = = =. Process 3-4 is isentropic = = = =. 22

29 = = = = P4 = kpa b. Change in entropy during isothermal expansion For mass of the working substance = = = = ln = ln 1.5 =. / c. Mean thermal efficiency of the cycle = 1 = =. % 683 d. Mean effective pressure of the cycle = = = ln / / / = ln / / / ln 1.5 = = e. Theoretical power if there are 210 working cycles per minute = = ln / = ln 1.5 = = = =. 23

30 2. A reversible engine converts one-sixth of the heat input into work. When the temperature of the sink is reduced by 70 C, its efficiency is doubled. Find the temperature of the source and the sink. = 1 6 = 70 = = 1 6 We also know that = 1 = 1 6 = 5 6 = 5 6 Again, = = 1 3 = 1 = 70 = 2 3 = = Solving for TL1 and TH TH = 420K TL1 = 350 K 3. An engine working on Otto cycle has a volume of 0.45 m 3, pressure 1 bar and temperature 30 C at the beginning of compression stroke. At the end of compression stroke, the pressure is 11 bar. 210 kj of heat is added at constant volume. Determine: a. Pressure, temperature and volume at salient points in the cycle b. Percentage clearance c. Efficiency d. Net work per cycle e. Mean effective pressure f. Ideal power developed by the engine if the number of working per minute is

31 P1 = 1 bar, V1 = 0.45 m 3 T1 = = 303 K P2 = 11 bar Qin = 210 kj a. Pressure, temperature and volume at salient points For mass of the air = = = For isentropic compression process 1-2 = = = = = 5.54 = = 0.45 = = = =. For constant volume heat addition process 2-3 = = =. = = = = =. = = For isentropic expansion process 3-4 = = = =. = = =. = =. 25

32 b. Percentage clearance = c. Efficiency = = % = 1 1 = 1 1 =. % d. Net work per cycle = = = = e. Mean effective pressure = = =. f. Power if revolution per minute is 210 = = = An engine with 200 mm cylinder diameter and 300 mm stroke works on theoretical Diesel cycle. The initial pressure and temperature of air used are 1 bar and 27 C. The cut off is 8% of the stroke. Determine if compression ratio is 15 and working fluid is air a. Pressure and temperature at all salient points b. Theoretical air standard efficiency c. Mean effective pressure d. Power of the engine if the working cycles per minutes are 380 Diameter (D) = 200 mm, Stroke (L) = 300 mm P1 = 1 bar, T1 = 300 K Cutoff = 8% of stroke, Compression ratio (r)= 15 = 4 = 8% = 8% 1 = = =

33 1 = = = 2.12 a. Pressure and temperature at all silent points For isentropic compression 1-2 = = = =. = = =. For constant pressure heat addition 2-3 = = = = =. = =. For isentropic expansion process 3-4 = = = =. = = =. b. Theoretical efficiency = = =. % c. Mean effective pressure = = = 15 Solving for V1 and V2 V1 = m 3, V2 = m 3 = = = = = = = = =

34 = = = =. d. Power at 380 rpm = = = In an engine working on Dual cycle, the temperature and pressure at the beginning of the cycle are 90 C and 1 bar respectively. The compression ratio is 9. The maximum pressure is limited to 68 bar and total heat supplied per kg of air is 1750 kj. Determine: T1 = = 363 K P1 = 1 bar a. Pressure and temperature at all salient points b. Air standard efficiency c. Mean effective pressure Compression ratio (rc) = 9 P3 = 68 bar qin,total = 1750 kj/kg a. Pressure and temperature at all salient points For the isentropic compression process 1-2 = = = =. = = =. For constant volume heat addition process 2-3 = = = =. Heat supplied at constant volume = = = / For constant pressure heat addition process 3-4 Heat added at constant pressure = = = / 28

35 Also, = = + = = = =. = = = = 1.15 For isentropic expansion process 4-5 = = = = =. = = =. b. Air standard efficiency Heat rejection at constant volume = = = / = 1 = =. % 1750 c. Mean effective pressure = = = = = = Calculate the efficiency and specific work output of a simple gas turbine working on the Brayton cycle. The maximum and minimum temperatures of the cycle are 1000 K and 288 K respectively, the pressure ratio is 6, and the isentropic efficiencies of the compressor and turbine are 85 and 90 percent respectively. T3 = 1000 K T1 = 288 K rp = 6 ηt = 90% ηc = 85% a. Efficiency of the cycle 29

36 For isentropic compression process 1-2 = = 1 = =... = For the turbine efficiency = = = = = For compressor efficiency = 0.85 = The cycle efficiency = = = 1 =. % b. Specific work output = = = = = =. 1. A Carnot engine working between 400 C and 40 C produces 30 kj of work. Determine: a. The engine thermal efficiency b. The heat added c. The entropy changes during heat rejection process 2. An inventor claims that a new heat cycle will develop 0.4 kw for a heat addition of 32.5 kj/min. Temperature of heat source is 1990 K and that of sink is 850 K. Is his claim possible? 30

37 3. An engine of 250 mm bore and 375 mm stroke works on Otto cycle. The clearance volume is m 3. The initial pressure and temperature are 1 bar and 50 C. If the maximum pressure is limited to 25 bar, find the following: a. The air standard efficiency of the cycle [56.5%] b. The mean effective pressure [1.334 bar] 4. In a constant volume Otto cycle, the pressure at the end of compression is 15 times that at the start, the temperature of air at the beginning of compression is 38 C and maximum temperature attained in the cycle is 1950 C. Determine: a. Compression ratio [6.9] b. Thermal efficiency [53.8%] c. Work done [597.5 kj] 5. A diesel engine has a compression ratio of 15 and heat addition at constant pressure takes place at 6% of stroke. Find the air standard efficiency of the engine. [61.2%] 6. The stroke and cylinder diameter of CI engine are 250 mm and 150 mm respectively. If the clearance volume is m 3 and fuel injection takes place at constant pressure for 5% of the stroke determine the efficiency of the engine. [59.3%] 7. Calculate the percentage loss in the ideal efficiency of a diesel engine with compression ratio 14 if the cut off is delayed form 5% to 8%. [2.1%] 8. The mean effective pressure of a Diesel cycle is 7.5 bar and compression ratio is Find the percentage cut off of the cycle if its initial pressure is 1 bar. 9. An oil engine working on the dual combustion cycle has a compression ratio 14 and the explosion ratio obtained form an indicator card is 1.4. If the cut off occurs at 6% of stroke, find the ideal efficiency. Take γ for air = 1.4. [61.4%] 10. The compression ratio for a single cylinder engine operating on dual cycle is 9. The maximum pressure in the cylinder is limited to 60 bar. The pressure and temperature of the air at the beginning of the cycle are 1 bar and 30 C. Heat added during constant pressure process upto 4% of the stroke. Assuming the cylinder diameter and stroke length as 250 mm and 300 respectively, determine: a. the air standard efficiency [57.56%] b. the power developed if the number of working cycles are 3 per second [51 kw] 31

38 Chapter 2. Reciprocating Steam Engine 2.1 Rankine cycle Rankine Cycle is the theoretical cycle on which steam power plant (such as nuclear power plant Fig. 2-1) works. In Rankine cycle has water as working fluid which is used to handle the phase change between liquid and vapor. Fig. 2-1 Rankine cycle when used in steam power plant The processes involved in a Rankine cycle are: Process 1-2: Reversible adiabatic compression in pump Process 2-3: Constant pressure transfer of heat in the boiler/steam generator Process 3-4: Reversible adiabatic expansion in the turbine Process 4-1: Constant pressure transfer of heat in the condenser In an ideal Rankine Cycle as shown in Fig. 2-2, the process 1-2, a pump is used to increase the pressure of the working fluid. The working fluid enters the pump as a saturated liquid (State 1, x1 = 0) and exits the pump as a sub-cooled liquid (state 2). The fluid entered into boiler has relatively low temperature is heated at constant pressure and leaves the boiler as a saturated vapor (state 3, x3 = 1). This saturated vapor is expanded isentropically through turbine to produce the work and leave as state 4. The low pressure saturated mixture is again condensed at constant pressure in the condenser leaving as low pressure low temperature saturated liquid (state 1). Following condensation, the liquid enters the pump. The working fluid is returned to the high pressure for heat addition at the higher boiler temperature, and the cycle is repeated. If we apply SFEE for four components of the Rankine cycle, we have For Boiler: Heat addition qin = h3 h2 For Pump: Work Absorbed wp = h2 h1 For Turbine: work produced wt = h3 h4 32

39 For Condenser: Heat loss qout = h4 h1 Fig. 2-2 Ideal Rankine Cycle So, efficiency of Rankine Cycle is: ( h3 h4 ) ( h2 h1 ) η = Eq. 2.1 ( h h ) As compared to wt, wp is very small so in many cases we can write, 3 2 η = ( h 3 ( h 3 h 4 h 2 ) ) Eq. 2.2 Fig. 2-3 P-v diagram of Rankine Cycle 2.2 Mean temperature of heat addition In Rankine cycle, heat is added reversibly at a constant pressure, but at variable temperature. If Tm is the mean temperature of heat addition, as shown in Fig. 2-4 so that the area under 2-3 is equal to the area under 2-3, then heat added qin = h3 h2 = Tm(s3 s2) 33

40 Tm = (h3 h2)/(s3 s2) qout = h4 - h1 qout = T2(s4 - s1) qout = T2(s3 s2) Fig. 2-4 Mean temperature of heat addition Now, efficiency of Rankine cycle = 1 = 1 = 1 Eq Comparison of Rankine and Carnot cycle We know that Carnot cycle is the most efficient engine for any temperature range but it is not preferred in vapor power cycle. When Carnot cycle is used in vapor power cycle, there are some practical difficulties. In the following section we will compare Carnot cycle and Rankine cycle when used as vapour power cycle. Fig. 2-5 Comparison between Rankine and Carnot cycle Fig. 2-5 considers three different cases for the comparison between Carnot and Rankine cycle. In each case operating temperature range is same for both Carnot and Rankine cycle. We know that the efficiency of Rankine and Carnot cycle depends on the operating temperature range such that (Eq. 2.3 and Eq. 1.4). = 1 = 1 34

41 Case a: TL is same for both cycle whereas (TH)Carnot is more than (Tm)Rankine. Therefore, ηcarnot is greater than ηrankine Case b: TL is same for both cycle whereas (TH)Carnot is more than (Tm)Rankine. Therefore, ηcarnot is greater than ηrankine Case c: TL is same for both cycle whereas (TH)Carnot is more than (Tm)Rankine. Therefore, ηcarnot is greater than ηrankine It shows that theoretically Carnot cycle is more efficient than Rankine cycle. But the Carnot cycle cannot be realized in practice because the pump work to increase the pressure in all cases is very large. Heat addition in case a and case b should be carried out at variable pressure which is difficult to achieve. In case c, the problem of heat addition at constant pressure is eliminated but to achieve the condition, it is difficult to control the quality at Effect of pressure and temperature on Rankine cycle Decreasing condenser pressure Let us consider the exhaust pressure (condenser pressure) is dropped from P4 to P4 as shown in the Fig. 2-6 Because of the drop in pressure, heat rejection temperature also drops to TL from TL. There is no significant change in mean temperature of heat addition (Tm). Therefore, the net result is an increase in efficiency. Fig. 2-6 Decreasing condenser pressure Fig. 2-7 Increasing boiler pressure Fig. 2-8 Superheating steam Increasing boiler pressure If pressure is increased to P2 from P1 keeping the maximum temperature same, the mean temperature of heat addition (Tm) is also increased while the temperature heat rejection (TL) remains same. Hence the efficiency also increases Superheating steam in boiler: When superheating of steam is increased, the mean temperature of heat addition (Tm) increases where as temperature of heat rejection (TL) remains the same which finally leads to the increase in cycle efficiency 35

42 2.5 Working principle of reciprocating steam engine The working principle of a reciprocating steam engine is shown in Fig In a reciprocating engine, the front port is exposed to steam chest pressure allowing the steam to enter the cylinder and start to drive the piston. The valve then starts to travel forward and will soon cut off the steam admission from the front port and expose the rear port. The piston will continue on to the end of its stroke at the rear of the cylinder. The valve traveled forward, exposing the rear port to the pressurized steam and allowed steam to enter the backside of the piston, which will drive it back again. The valve then moves back in the original direction as the piston continues forward. The valve will soon cover the rear port and expose the front port to begin the process all over again. The left port is open allowing steam chest pressure into the left side of the cylinder which pushes the piston towards the right. The valve is starting to travel left and will soon cut off steam through the left port. The piston will continue to the end of its stroke due to flywheel momentum. The valve has traveled fully left exposing the right port to pressurized steam.the piston will be driven towards the left. The left side of the cylinder is now exposed to the exhaust port allowing old steam to vent. Fig. 2-9 Working mechanism of reciprocating steam engine As the piston continues its stroke the valve again begins moving towards the right. It will soon close the right port and open the left port driving the system towards the condition in diagram A. 36

43 Valve action in relation to piston action is shown in Fig Steam chest is filled with high pressure steam at all times. A valve admits the steam into the cylinder through ports in the cylinder wall. The same valve allows steam to escape through a center exhaust port. Since steam force is used on both sides of the piston the engine is called Double Action. This design allows very low rpm and high torque. Single acting engines operate by admitting steam to only one side of a piston. The other side of the piston is exposed to a much lower atmospheric pressure. They produce power for only 50% of the revolution. 2.6 Steam engine indicators Engine indicator is a mechanical device, which is used to analyze the change in pressure with respect to the piston movement. It can plot the graph showing the pressure inside the cylinder at every point of the stroke. Fig Engine indicator The device is fitted with a plotting mechanism, pencil and paper on which the diagram is drawn. As the piston moves back and forth and as the pressure rises and falls, the pencil will draw a diagram indicating the pressure in the cylinder at every point of the stroke. A provision is provided in such a way that the paper move together with the piston. The vertical and horizontal movement of pencil is reduced by appropriate mechanism so that the diagram will be in reduced scale. The diagram obtained from indicator is also called indicator diagram. 2.7 Hypothetical indicator diagram If we consider the single acting steam engine with zero clearance volume, the operations can be divided into following processes: Process 1-2: Constant boiler pressure (Pa) admission of steam Process 2-3: Expansion of steam which is assumed to follow the relation Pv = constant Process 3-4: Constant volume release of steam Process 4-5: Constant pressure release of steam at back pressure (Pb) 37

44 The total work done can be calculated as: If expansion ratio r = V3/V2 We know that, Fig P-v diagram of steam engine = = + log = + log = + log Eq. 2.4 = = + log = + log = 1 + log Eq. 2.5 If clearance volume is not considered zero, the P-v diagram of steam engine will be as shown in Fig As in previous case, work done can be calculated as: 38

45 Fig P-v diagram of engine with clearance volume = = + log Where, V3/V2 = r = + log Eq. 2.6 Similarly = + log Eq Hypothetical and actual indicator diagram The hypothetical and actual indicator diagram is shown in the Fig The solid line represents the hypothetical diagram and dotted line represents actual diagram. Fig Hypothetical and actual indicator diagram 39

46 The various points of actual indicator diagram as shown in the figure are: A Admission of steam B Cutoff of steam C Release of steam D The exhaust port closes and trapped steam in clearance volume is compressed E Admission port opens and the trapped steam is mixed with admission steam. There is some deviation in actual indicator diagram compared with hypothetical indicator diagram. The admission of steam in actual is not at constant pressure. The pressure gradually drops which is because of condensation of steam and pressure loss during steam flow. The expansion process is not hyperbolic as assumed in hypothetical case. The opening and closing of admission and exhaust port take some time so the region around cutoff, release and admission of steam is not sharp. The steam left in clearance volume is compressed at D since exhaust port is closed. The compression continues until the admission port opens at A. The low pressure steam left in clearance volume is mixed with high pressure admission steam which drops the admission pressure to A. The area of actual indicator diagram is less than area of hypothetical indicator diagram. The ratio of the area of actual indicator diagram to the area of hypothetical indicator diagram is called Diagram Factor (DF). = hh = hh = Eq

47 Solved Numerical Problems 1. In a Rankine cycle steam leaves the boiler and enters the turbine at 4 MPa, 400 C. The condenser pressure is 10 kpa. Determine, a. The pump work per kg b. The work output per kg c. The cycle efficiency d. The condenser heat flow per kg Boiler pressure = 4 MPa Temperature T3 = 400 C Condenser pressure = 10 kpa From steam table, at 4 MPa and 400 C the steam is in superheated state. The following properties can be noted from the steam table for 4 MPa and 400 C. h3 = kj/kg s3 = kj/kgk Since process 3-4 is isentropic, the entropy at state 3 and 4 are same. s4 = kj/kgk Since state 4 is in two-phase region, from steam table (saturated water), for 10 kpa sl = kj/kgk and slg = kj/kgk hl = kj/kg and hlg = kj/kg = = = 0.82 Similarly for h4 h = h + h h = h = / The state 1 is in saturated liquid line and has pressure of 10 kpa h1 = hl = kj/kg The process 1-2 is an isentropic pumping of water. The water is incompressible substance so the work required to increase the pressure of water from pressure P1 to P2 can be written as: 41

48 = v1 is the specific volume of saturated water at pressure P1. So from steam table, v1 = m 3 /kg. So, = =. / Pump work can also be expressed as = h h h = + h = = / Work output per kg = h h = =. / The cycle efficiency = h h h h h h =. % Condenser heat flow per kg = = h h = =. / 2. Conventional indicator card without clearance shows the percentage cut-off as 33%. Intake pressure is 9.85 bar and exhaust pressure is bar. For a cm double acting single cylinder steam engine with a mean piston speed of 18 m/s, find the Indicated Power for a diagram factor of Neglect the piston rod area. Pa = 9.85 bar Pb = bar Cutoff = 33% of stroke Bore (D) stroke (L) = cm Mean piston speed = 18 m/s Diagram factor = 0.78 The stroke/swept volume is, = = 4 = Since, the cutoff is 33% of the stroke = = 0.33 = = Theoretical mean effective pressure for single acting cylinder 42

49 = = + ln ln = = 5.72 = = = 4.46 In one revolution, piston covers 2L distance. So in N rpm, the mean piston velocity can be expressed as, = 2 60 = 60 2 = = 900 Actual indicated power for double acting cylinder can be calculated as = 2 60 =. = 2 60 = Determine the actual mean effective pressure for a steam engine receiving steam at a pressure of 6 bar; cut-off takes place when the piston has travelled 0.4 of the stroke in which clearance volume is 10% of the stroke volume. Back pressure is 1.03 bar and the diagram factor is 0.7. Pa = 6 bar Pb = 1.03 bar Cutoff = 0.4 of stroke Clearance volume = 10% of stroke volume Diagram factor = 0.7 = = 0.1 = 0.4 = = 0.5 = = + = = 1.1 Theoretical mean effective pressure is = = + ln + 43

50 = ln = ln = ln = 3.73 = = =. 44

51 Chapter 3. Internal Combustion Engine 3.1 Introduction Any type of engine or machine which derives heat energy form the combustion of fuel or any other source and converts this energy into mechanical work is termed as heat engine. Heat engine may be classified as follow: Fig. 3-1 Classification of heat engine External combustion engine: In external combustion engine, the fuel that runs the engine is burned outside the engine. Example: Steam turbine Internal combustion engine (IC engine): In IC engine, the fuel that runs the engine is burned inside the cylinder of the engine. Example: Automobile In reciprocating engine, piston, connecting rod and crank-shaft are used to convert reciprocating motion into rotary motion. There are two types of reciprocating engines: Spark-Ignition engine (SI engine) and Compression-Ignition engine (CI engine). The differences between the two are: The types of fuel used The way the fuel gets into the engine cylinder The way the fuel is ignited The spark-ignition engine uses a highly volatile fuel which turns to vapor easily, such as gasoline. The fuel is mixed with air before it enters the engine cylinder. The fuel turns into a vapor and mixes with the air to form a combustible air-fuel mixture. This mixture then enters the cylinders and is compressed. Next, an electric spark produced by the ignition system sets fire to, or ignites, the compressed air fuel mixture. In the compression-ignition engine, the fuel is mixed with the air after the air enters the engine cylinder. Air alone is taken into the cylinder of the diesel engine. The air is then compressed as the piston moves up. The air is compressed so much that its temperature goes up to 550 C or higher. Then the diesel-engine fuel is injected into the engine cylinder. The hot air, or heat of compression, ignites the fuel. 45

52 3.2 Classification of IC engines Internal-combustion engine may be classified according to: Number of cylinder: o Single cylinder or multi cylinder Arrangement of cylinder: o Horizontal engine o Vertical engine o V-type engine o Radial engine Fig. 3-2 Cylinder arrangement Arrangement of valves: o Overhead type o T-head type Types of cooling o L-head type o F-head type o Air cooled or liquid cooled Number of strokes per cycle o Two stroke or four stroke Type of fuel used o Gasoline (Petrol) or Diesel Method of ignition o Compression ignition or spark ignition Reciprocating or rotary 3.3 Working cycle of IC engines An internal combustion engine can work on any one of the following cycles: 1. Constant volume or Otto cycle 2. Constant pressure or Diesel cycle 3. Dual combustion cycle 46

53 3.3.1 Engine operation- four stroke SI cycle 1. Intake stroke: During the intake stroke (Suction stroke/induction stroke), the piston moves downward form TDC (Top Dead Centre) to BDC (Bottom Dead Centre). The intake valve is open. As the piston moves down, vacuum is created inside the cylinder. So airfuel mixture enters the cylinder through the inlet valve. As the piston passes through BDC, the intake valve closes. Since the outlet valve is still closed, the upper end of the cylinder is sealed off. 2. Compression stroke: After the piston passes through BDC, it starts moving up. The air fuel mixture is compressed. The degree of compression is based on the compression ratio of the engine. The average compression ratio of SI engine is 8:1. Fig. 3-3 Four stroke SI engine operating cycle 3. Power stroke (Expansion stroke): As the piston nears TDC on the compression stroke, an electric spark is produced by spark plug in the cylinder. The spark sets fire to the compressed air-fuel mixture. The temperature of burning mixture rises up to 3300 C and the pressure inside the cylinder also increases. The work is obtained during this stroke. The high pressure in the cylinder pushes the piston down. The downward push is carried through the connecting rod to the crankshaft. The flywheel is mounted on the engine shaft to store energy so that it can be used during remaining three ideal strokes. 4. Exhaust stroke: As the piston approaches BDC on the power stroke, the exhaust valve opens. Now, as the piston moves up again after BDC, the burned gases escape through the exhaust valve. Then, as the piston nears TDC, the intake valve opens. As the piston passes through TDC and start down again, the exhaust valve closes. Now another intake stroke takes place. 47

54 3.3.2 Engine operation- four stroke CI cycle As in four stroke SI engine, four stroke CI engine is also completed in four strokes: intake stroke, compression stroke, power stroke and exhaust stroke. The working principle of each stroke is almost similar as it is in SI cycle. During intake stroke, only air is pumped in the cylinder unlike air-fuel mixture in SI engine. The air is compressed with compression ratio of around 22:1. As the air is compressed the temperature of air rises up to 538 C. As piston nears TDC on compression stroke, the fuel injector sprays diesel into combustion chamber. The high temperature-air ignites the fuel and the power stroke and then exhaust stroke follows. Fig. 3-4 Four stroke CI engine operating cycle Engine operation-two stroke cycle The Fig. 3-5 shows a two stroke petrol engine. During upward stroke of the piston, the gas in the piston is compressed and at the same time fresh air-fuel mixture enters the crank chamber through the valve V. At the end of the compression, spark plug ignites the air-fuel mixture burns. The increased pressure in the cylinder pushes the piston and near the end of the stroke, the piston uncovers the exhaust gas port and exhaust gas escape through the port. During downward movement, the air-fuel mixture in the crank case (CC) also gets compressed. As soon as the transfer port (TP) is uncovered by the down moving piston, the air-fuel mixture form the crank case enters to the cylinder. The special shape in the piston top helps air-fuel mixture to flow upward and helps the exhaust gas to escape out of the exhaust port. During exhaust, some of the unburned air-fuel mixture also escapes through exhaust port along with the burned gas. As the piston again moves upward, the air-fuel mixture gets compressed and another cycle is repeated. 48

55 Fig. 3-5 Two stroke engine 3.4 Valve timing diagram of four stroke IC engine In describing the operation of the four stroke cycle engine, it was explained that the inlet valve is open during the suction stroke and the exhaust valve during the exhaust stroke. But in real practice the valve opening timing is different. Fig. 3-6 Actual valve timing for four stroke engine The Fig. 3-6 shows the typical valve timing diagram. Intake valve opens about 20 before TDC. This allows the valve to be open completely when suction strokes starts. The intake valve remains open well after the piston reaches the BDC during suction stroke. This gives 49

56 additional time for air-fuel mixture or air to flow into the cylinder. The delivery of adequate amount or charge to the cylinder is the critical item in the engine operation. Actually, the cylinders are never quite filled up when intake valve closes especially during high speed. This period varies from 30 to 70 degree in modern automotive engines. In similar manner, exhaust valve starts to open about 35 before piston reaches BDC on the power stroke and stays open until 10 after TDC on the intake stroke. This gives more time for the exhaust gas to leave the cylinder. By the time the piston reaches 35 before BDC on the power stroke, the combustion pressure has dropped considerably. Little power is lost by giving the exhaust gas this extra time to leave the cylinder. Closing the exhaust valve after TDC on suction stroke allows exhaust gases to move rapidly for the cylinder into exhaust port thus prevents the exhaust gas to be retained in the clearance space of the cylinder. The spark plug produces spark about degree before TDC on power stroke thus fuel gets more time to burn. Exercise for you List the major differences between SI engine and CI engine. What are the differences between two stroke and four stroke engine 50

57 3.5 Components of IC engines Fig. 3-7 Engine components The working principle of CI and SI engine is almost same so the construction of both engines is same. There are numbers of components common to both engines. 1. Cylinder block/cylinder: The cylinder block is the foundation of the engine. Everything else is put inside of or attached to the block. Most cylinder blocks are cast in one piece form grey iron or iron alloy or aluminum alloy. It contains large holes for cylinder bore where the gas is compressed (Fig. 3-7) 51

58 2. Piston and piston rings: Piston is usually made of aluminum alloy. Piston can slide up and down in the cylinder easily. Piston undergoes great stress. During power stroke, up to 1814 kg is suddenly applied to the piston head. This happens 30 to 40 times a second at high speed. The temperature above the piston head can reach 2200 C. The piston must be strong. But it must be light, too, to reduce inertia loads on the bearing. Modern automotive engines use aluminum alloy piston. Since the diameter of piston is smaller than that of cylinder, the gap must be sealed to avoid the leak of compressed air-fuel mixture (in SI engine)/air (in CI engine) and high pressure burned gas. The escape of unburned and burned gas from the combustion chamber, past the pistons, and into the crankcase is called blow by. Blow by would greatly reduce the efficiency of the engine. To avoid this, piston rings are installed on the piston. The piston rings are split at one point so they can be expanded slightly and slipped over the piston and into the grooves cut in the piston. Piston rings are of two types and they do two jobs: a. Compression rings: The compression rings seal in the unburned gas as it is compresses. They also seal in the combustion pressure as the mixture burns. b. Oil-control rings: Oil-control rings scrape excessive oil that is splashed on the wall so that it does not get up into the combustion chamber where it would burn. Fig. 3-8 Piston and piston rings 3. Cylinder head: The cylinder head encloses one end of the engine cylinders and forms the upper end of the combustion chambers. The cylinder head includes water jackets and passages from the valves ports to the openings in the manifolds. 52

59 Fig. 3-9 Combustion chamber 4. Inlet and exhaust manifold: The intake manifold is a series of tubes that carry air to the engine cylinders. The exhaust manifold is a set of tubes that carry the exhaust gases form the engine cylinder. 5. Connecting rod: The connecting rod is attached at one end to a crankpin on the crankshaft. It is attached at other end to a piston, through a piston pin. The connecting rod must be very strong and rigid, and as light as possible. The connecting rod carries the power thrust form the piston to the crankshaft. 6. Crankshaft: The crankshaft is a strong one-piece casting or forging of heat-treated alloy steel. The crankshaft must be strong enough to take the downward push of the piston during the power strokes without excessive twisting. In addition, the crankshaft must be carefully balanced to eliminate undue vibration resulting form the weight of the offset cranks. To provide balance, crankshafts have counterweight opposite to the cranks. Crankshafts have drilled oil passage through which oil flows form the main to the connecting-rod end. Fig Crankshaft 53

60 7. The valves: Most engines have two holes in the enclosed upper end of the cylinder. One of two holes is the intake valve. It allows the air or air-fuel mixture or air to enter the cylinder. The other is exhaust valve. It allows the burned gases to exhaust form the cylinder. Fig Valve mechanism 8. Engine bearing: Bearings are placed in the engine wherever there is rotary motion between engine parts. These engine bearings are called sleeve bearing because they are shaped like sleeves that fit around the rotating shaft. The part of the shaft that rotates in the bearing is called a journal. Connecting-rod and crankshaft bearings are of the split, or half, type. Typical bearing half is made up of a steel or bronze back. The bearing material is soft. Therefore the bearing wears with more ease compared with the other mechanical part of the engine. The cost of bearing is less than that of engine part so the replacement cost of bearing is less. 9. Crank case: The bottom of the cylinder block and the oil pan form crank case. The oil pan holds lubricating oil. When the engine is running, the oil pump sends oil form the oil pan up to the moving engine parts. 10. Fly wheel: Fly wheel attached with one end of crank shaft performs the following functions: a. Stores energy required to rotate the shaft during ideal strokes (intake, compression and exhaust strokes) b. Makes crank shaft rotation more uniform. c. Facilitates the starting of the engine. 3.6 Parts common to SI engine 1. Spark plug: The main function of spark plug is to conduct the high potential form the ignition system into the combustion chamber. The spark plug is a metal shell in which a porcelain insulator is fastened. An electrode extends through the centre of of the 54

61 insulator. The metal shell has a short electrode attached to one side. The outer electrode is bent inward to produce the proper gap between it and the centre electrode. High tension current jumping from the supply electrode produces the necessary spark. The correct type of plug with correct gap between the electrodes is important factor. Fig Spark plug 2. Carburetor: Carburetion is the mixing of gasoline fuel with air to get a combustible mixture. The function of carburetor is to supply a combustible atomized fuel and air mixture of varying degree of richness to suit the engine operation conditions. The mixture must be rich for starting, acceleration and high speed operation. The lean mixture is desirable at intermediate speed with a warm engine. 3.7 Parts common to CI engine 1. Fuel injector: Fuel injector injects the fuel inside the cylinder of CI engine at the start of the expansion stroke. 2. Fuel pump: The fuel form fuel tank is pumped to the fuel injector by fuel pump. 3.8 Basic engine parameters 1. Top dead centre (TDC): The top most position that piston can reach. 2. Bottom dead centre (BDC): The lowest position that piston can reach. 3. Stroke length: The distance between TDC and BDC or length covered by piston during one stroke 4. Bore: Diameter of the cylinder 5. Swept volume (Vs): It is the product of cross-section area of the cylinder and stroke length. It can also be defined as a volume covered by the piston during one stroke. Engine capacity is defined in terms of swept volume expressed in cc. A four cylinder engine marked as 1.2 ltr has four cylinders each having swept volume of 300 cc. 55

62 6. Clearance volume (Vc): Volume left above the piston when the piston is in TDC. 7. Compression ratio (r): r = (Vs + Vc)/Vc Fig Bore stroke 56

63 Chapter 4. Performance of Internal Combustion Engine 4.1 Mean effective pressure (MEP) When work done per cycle is divided by swept volume per cycle, the parameter obtained is called mean effective pressure. Mean Effective Pressure (MEP) can also be defined as the pressure that, if it acted on the piston during the entire power stroke, would do an amount of work equal to that actually done on the piston (Fig. 4-1). Fig. 4-1 Mean effective pressure = Eq Indicated power (IP) Fig. 4-2 Pressure in the cylinder during each stroke Indicated power is the total power that the engine develops inside the combustion chamber during the combustion process. A special device is required to measure IP. It measures the pressure in the engine cylinder. As shown in the Fig. 4-2 pressure is highest during power 57

64 stroke. The average of pressure in four strokes is also called indicated mean effective pressure. The relation between indicated mean effective pressure and IP can be derived as follow: From Eq. 4.1 = = [L = Length of stroke, A = Cross-section area of the cylinder] = = 60 = 60 For n cylinder engine = 60 In four stroke engine, power is generated once in two revolution of the crankshaft but in two stroke engine power is developed in every revolution of engine. So equation of IP can be written in general terms as, = Eq. 4.2 Where, IP = Indicated power (kw) n = Number of cylinder Pm = Indicated mean effective pressure (N/m 2 ) L = Length of stroke (m) A = Cross-section area of cylinder (m 2 ) N = rpm of crank shaft. k = 1 for two stroke engine and 1/2 for four stroke engine. 4.3 Brake power (BP) The power developed by an engine at the output shaft is called the brake power. Not all the IP developed by the engine is available as useful power to do work. Part of is lost in the engine as friction power (FP). FP is the power required to overcome the friction of the moving parts in the engine. One of the major causes of friction loss is piston-ring friction. In addition to the friction loss, FP also includes the work of charging absorbed during exhaust and suction stroke. Resistance of air to flywheel rotation and power required to drive the auxiliaries. 58

65 BP = IP FP BP bmep = knlan Eq. 4.3 Eq. 4.4 Where, BP = Brake Power (kw) n = Number of cylinder bmep = Break mean effective pressure (N/m 2 ) L = Length of stroke (m) A = Cross-section area of cylinder (m 2 ) N = rpm of crank shaft. 4.4 Engine efficiencies Mechanical efficiency BP η mechanical = IP Eq. 4.5 Brake thermal efficiency η B, thermal = BP mc f Eq. 4.6 Indicated thermal efficiency η I, thermal = IP mc f Eq. 4.7 Where, BP = Brake Power, IP = Indicated power, m = mass of fuel, Cf = Calorific value or heating value of the fuel. Volumetric efficiency: During intake stroke, the passage of air is restricted by filter, carburetor and throttle plate. The parameter used to measure the effectiveness of an engine induction process is called volumetric efficiency. It is the ratio of the volume Va of air admitted or air-fuel mixture admitted to the engine cylinder during suction referred to NTP to the suction volume of the piston. η volumetric V = V a p Eq. 4.8 Relative efficiency η relative = actualindicatedthermalefficiency Idealair standardefficiencyfor samecompression ratio Eq. 4.9 Air-fuel ratio (Fuel-air ratio): It is the ratio of mass of air to the mass of fuel in airfuel mixture. Stoichiometric air-fuel ratio: Ratio of amount of air (oxygen in air) required to combust a certain amount of fuel in chemically balanced condition. According to chemical reaction, 14.7 kg of air is required to burn 1 kg of gasoline. So the stoichiometric A/F ratio for gasoline is 14.7:1. Similarly that of diesel is 14.6:1. 59

66 Relative air-fuel mixture: Ratio of actual A/F ratio to stoichiometric A/F ratio. It is also known as lamda. λ = ( A / F ) actual ( A / F ) Stoich Eq Lamda of 1 is stoich mixture, rich mixtures are less than 1 and lean mixtures are more than 1. Equivalence ratio (φ): Ratio of actual F/A ratio to stoichiometric F/A ratio. It is an φ = inverse of λ ( F / A) actual ( F / A) Stoich Eq Specific fuel consumption m f sfc = (kg/kwh) BP Eq Where, mf= mass of fuel used per hour 4.5 Heat balance for IC engine First law of thermodynamics for a steady flow open system can be well applied for the analysis of the overall heat (energy) balance for the IC engine. According the principle, total energy leaving the system is equal to the total energy incoming to the system. In case of an IC engine, the relation can be expressed as P b Q cool + Q misc + H e = m f Q LHV Eq In the above Eq. 4.13, m f is the mass flow rate of fuel entering the cylinder. It combined with lower heating value of fuel (QLHV), represents the total energy incoming the cylinder in the form of fuel. The fraction of heat produced upon burning of fuel is used for brake power (Pb). Remaining heat is lost through the cooling water ( Q ), exhaust gas enthalpy ( cool H e). and miscellaneous loss ( Q ). Miscellaneous heat loss includes the friction power lost in misc bearings, valve mechanism and heat lost during cooling by lubricating oil. Typical values of each of each of these terms with reference to percentage of fuel heating value are given in the table below... Pb... Q cool Q misc H e Percentage of fuel heating value SI engine CI engine

67 Energy balance can be illustrated through the Fig. 4-3below. Fig. 4-3 Energy balance in IC engine 4.6 Torque-power-speed relationship The torque that an engine can develop changes with engine rpm. During intermediate speeds, volumetric efficiency is high. There is sufficient time for the cylinder to become fairly well filled up. This means that with a fairly full charge of air-fuel mixture, higher combustion pressure will develop. With higher combustion pressure, the engine torque is higher. But, at higher speed, volumetric efficiency drops off. There is not enough time for the cylinders to become filled up with air-fuel mixture. Since there is less air-fuel mixture to burn, the combustion pressure is not as high. There is less push on the pistons. Therefore, engine torque is lower. The Fig. 4-4 shows how the torque drops off as engine speed increases. The decrease in BP is due to reduced torque at higher speed and to increased FP at the higher speed. Note that the curves are for one particular engine only. Different engines have different torque and BP. Peaks may be at higher or lower speed. Fig. 4-4 Torque-power-speed relationship 61

68 The empirical equation that defines the relation between shaft power and the engine speed is N N N P = P + max N max N max N max 2 Eq Where, P = Brake Power Pmax = maximum power an engine can produce (obtained in engine specification) Nmax= shaft rpm at which engine can produce maximum power Engine shaft power and shaft torque that engine can develop can be related as P = 2πNT 60 Eq Where, P = Brake Power, N = engine rpm, T = torque at engine shaft sfc kg/kwh Power kw sfc kg/kwh Torque N-m sfc 40 Torque sfc 10 Power RPN r pm Gasoline and gaseous fuel system Figure 4-1 Torque-sfc and Power-sfc relationship Gasoline Gasoline is a hydrocarbon (abbreviated HC), made up largely of hydrogen and carbon compounds. The resulting exhaust gas contains water vapor, carbon dioxide, and the pollutants carbon monoxide (partly burned gasoline) and hydrocarbons (unburned gasoline). Gasoline is made from crude oil by a refining process that also produce engine lubricating oil, diesel fuel oil, and other products. During the refining process, several additives are put into the gasoline to improve its characteristics. Good gasoline should have: 1. Proper volatility, which determines how quickly gasoline vaporizes 2. Resistance to spark knock, or detonation 3. Oxidation inhibitors, which prevent formation of gum in the fuel system 4. Antirust agents, which prevent rusting of metal parts in the fuel system 62

69 5. Anti-icers, which retard carburetor icing and fuel-line freezing 6. Detergents, which help keep the carburetor clean 7. Dye for identification After gasoline is mixed with air in the carburetor, the gasoline must vaporize quickly, before it enters the engine cylinder. If the gasoline is slow to vaporize, tiny drops of liquid gasoline will enter the cylinders. Because these drops do not burn, some of the fuel is wasted. It goes out the tail pipe and helps create atmospheric pollution. Also, the gasoline drops tend to wash the lubricating oil off the cylinder walls. This increases the wear on the cylinder walls, piston rings, and pistons. The ease with which gasoline vaporizes is called its volatility. A high-volatility gasoline vaporizes very quickly. A good gasoline should have just the right volatility for the climate in which the gasoline is to be used. If the gasoline is too volatile, it will vaporize in the fuel system. The result will be a condition called vapor lock. It prevents the flow of gasoline to the carburetor. Vapor lock causes the engine to stall from lack of fuel Carburetion system: Carburetion is the mixing of gasoline fuel with air to get a combustible mixture. The function of carburetor is to supply a combustible atomized fuel and air mixture of varying degree of richness to suit the engine operation conditions. Atomization is breaking of fuel into fine droplets. Each droplet is then exposed to air so that it vaporized quickly. It would be desirable to pass on the fuel in completely vaporized phase mixed with air but complete vaporization is not possible. The mixture must be rich for starting, acceleration and high speed operation. The lean mixture is desirable at intermediate speed with a warm engine. Fig. 4-5 Basic carburetor construction Basic components of carburetor are venturi tube, fuel reservoir, throttle valve and float system. The carburetor works on Bernoulli s principle. As air passes the venture tube, some of static head of air is converted to velocity head. The high velocity air through the venture creates partial vacuum or suction in it. The suction draws the gasoline form the discharge jet. The fuel gets mixed with the air flowing through the venture. The level of fuel in fuel reservoir and in the discharge tube is maintained by the float system in the reservoir. As the fuel level in the reservoir falls, the float moves down and the needle valve opens thus the 63

70 fuel flows in the reservoir. When fuel level rises to certain level, the float moves up and pushes needle valve into the valve seat Air mixing As discussed in the previous section, air is mixed with fuel in carburetor and combustible mixture is sent to the combustion chamber in intake stroke. The ideal mixture of air and fuel is called stoichiometric mixture (λ or φ = 1). But mixture requirements are different depending on operating condition. Different operating conditions and their respective air mixing process are discussed as follow. Idle system: When throttle valve is closed or only slightly opened, only a small amount of air can pass through the air horn. The air speed is low, and very little vacuum develops in the venture. This means fuel nozzle does not discharge fuel. Therefore the carburetor must have another system to supply fuel when the throttle is closed or slightly open. This system, called idle system, is shown in the Fig It includes passage through which air and fuel can flow. The air passage is called air bleed. With the throttle valve closed there is a high vacuum below the throttle valve form the intake manifold. Atmospheric pressure pushed air and fuel through the idle mixture screw. The mixture has high proportion of fuel. Fig. 4-6 Idle system Fig. 4-7 Low speed operation Low-speed operation: When the throttle valve is open slightly, as shown in Fig. 4-7, the edge of the throttle valve moves past the low speed-operation port in the side of the air horn. Therefore additional fuel is fed into the intake manifold through the low-speed port. This fuel mixes with the additional air moving past the slightly opened throttle valve. The additional mixture fuel provides sufficient mixture richness for part-throttle low-speed operation. Main-metering system: When the throttle valve is opened enough, sufficient air moves through the air horn to produce a vacuum in the venture. As a result, the fuel nozzle begins to discharge fuel. The wider the throttle is opened and the faster the air flows through the air horn, the greater the vacuum in the venture. This means that additional fuel will be 64

71 discharged from the main nozzle. As the result nearly constant air-fuel ratio is maintained by the main-metering system form part to wide opened throttle. Fig. 4-8 Main metering system Power enrichment system: For high-speed full power wide-open-throttle operation, the air-fuel mixture must be enriched so engine can deliver its maximum power but utilizing all the oxygen present in induced air. The rich mixture ensures the consumption of all the oxygen. Additional device are incorporated in the carburetor to provide the enriched mixture during high-speed-full-power operation. Accelerator pump: When the throttle plate is opened rapidly, the fuel-air mixture flowing into the engine cylinder leans out temporarily. The primary reason for this is time lag between fuel flow into the air stream at the carburetor and fuel flow past the intake valve. While much of the fuel flow into the cylinder is fuel vapor or small fuel droplets carried by the air stream, a fraction of the fuel flows into the manifold and port walls and form a liquid film. The fuel which impacts on the walls evaporates more slowly than fuel carried by the air stream and introduces a lag between the air/fuel ratio produced at the carburetor and air/fuel ratio delivered to the cylinder. An accelerator pump is used as the throttle plate is opened rapidly to supply additional fuel into the air stream at the carburetor to compensate for this leaning effect Temperature effect When the temperature of the surrounding drops considerably than normal, only part of the fuel vaporizes. Therefore extra fuel must be delivered to get the combustible air fuel mixture that permits the engine to start. So during cold weather, the carburetor must supply rich mixture. The elementary carburetor cannot enrich the mixture as required for cold start up. For this purpose, choke system is supplied with elementary carburetor. Primary element of choke system is a plate kept upstream of the carburetor. Choke system The working of choke can be explained with the help with the help of the Fig During cranking, air speed through the carburetor air horn is very low. Vacuum form the venturi 65

72 action and vacuum below the throttle valve would be insufficient to produce adequate fuel flow for starting. To produce enough fuel flow during cranking, the carburetor has a choke. When the choke is closed, it is almost horizontal. Only a small amount of air can get past it. The valve has choked off the air flow. Then, when the engine is cranked with choke closed, a fairly high vacuum develops in the air horn. This vacuum causes the main nozzle to discharge a heavy stream of fuel. The quantity delivered is sufficient to produce the air-fuel mixture needed for starting the engine. Fig. 4-9 Choke system Altitude effect An inherent characteristic of the conventional carburetor is that it meters fuel flow in proportion to the air volume flow rate. Air density changes with ambient pressure and temperature but change in pressure with altitude is most significant. To reduce the impact of changes in altitude, modern carburetors are fitted with provisions for altitude compensation Gasoline fuel injection system Fig Distribution of air fuel mixture in intake manifold One of the most difficult problems in a carbureted system is to get the same amount and richness of air-fuel mixture to each cylinder. The problem is that the intake manifold acts as 66

73 sorting device, sending a richer air-fuel mixture to the end cylinders (Fig. 4-10) since the air flow readily around corners and through variously shaped passages. However, the fuel is unable to travel as easily around the bends in the intake manifold. As a result, some of the fuel particles continue to move to the end of the intake manifold, accumulating or puddling there. This enriches the mixture going to the end cylinders. The centre cylinder, closest to the carburetor, get the leanest mixture. The port fuel-injection system (Fig. 4-11) solves this problem because the same amount of fuel is injected at each intake-valve port. Each cylinder gets the same amount of air-fuel mixture of the same mixture richness. In port fuel-injection system, the fuel is injected into the intake manifold through fuel-injection valves. Injection valve is positioned in the intake port near the intake valve. Fig Port injection system Electronic fuel injection The development of solid-state electronic devices such as diodes and transistors made electronic fuel injection possible. In this system, fuel metering is controlled primarily by engine speed and the amount of air that actually enters the engine. Fig Basic block diagram of Electronic Fuel Injection system 67

74 The airflow sensor in the air intake measures the amount of air that enters. Modern electronic fuel-injection systems include an oxygen sensor to measure the amount of oxygen in the exhaust gas and send this information to the electronic control unit. If there is too much oxygen, the mixture is too lean. If there is too little, the mixture is too rich. In either case, the ECU adjusts air-fuel ratio by changing the amount of fuel injected. 4.8 Ignition system The ignition system supplies high voltage surges to the spark plugs in the cylinders. These surges produce electric sparks across the spark-plug s electrode gap. The spark ignites the air-fuel mixture. It must create this spark at the appropriate time during the compression stroke. Usually spark timing is set to give maximum brake torque for the specific operating condition. For a given engine design, this optimum spark timing varies as engine speed, inlet manifold pressure and mixture composition vary. Thus, in most applications, and especially the automotive application, the system must have means for automatically changing the spark timing as engine speed and load vary. When the engine is idling, the spark appears at the plug gap just as the piston nears TDC on the compression stroke. When the engine is operating at higher speed, or with part throttle, the spark is advanced. It is moved ahead and occurs earlier in the compression stroke. This gives the compressed mixture more time to burn and deliver its energy to the piston Contact point ignition system (Conventional system) The basic circuit of contact point ignition system is shown in the Fig It includes the battery, the primary and secondary coil, the ignition distributor, the spark plugs and the wires and cables that connect them. The distributor has a shaft that is driven by gear on the cam shaft. There are two separate circuits through the distributor. One is primary circuit and the other is secondary circuit. The primary circuit includes the battery, the ignition switch, primary resistance, primary winding (consists few hundred turns of relatively heavy wires) in the ignition coil, contact point circuit breaker, and primary wiring. As the distributor cam rotates, the cam lobe pushes the arm out so that the contact point is moved away from the stationary point and primary circuit breaks. As soon as the lobe passes out, the spring bring back the arm the primary circuit is connected. There are same numbers of lobes on the cam as there are cylinders in the engine. The secondary circuit consists of the cables that connect the secondary winding (consists of thousands of turns of a very fine wire) to the cap centre terminal and the outer cap terminal to the spark plugs. 68

75 Fig Circuit diagram of contact point ignition system When the contact points are closed, they connect the primary winding of the ignition coil with the battery. Current flows through the coil, causing a magnetic field to build up around it. Then, when the points are opened, this disconnects the primary winding form the battery. The resulting decay of magnetic flux in primary coil induces the short pulse of high voltage in the secondary winding of the coil. The high-voltage surge (equal to break down potential of spark plug) flows through the distributor cap and rotor to the spark plug in the cylinder in which piston is nearing the end of compression stroke. Centrifugal advance: As engine speed increases, the spark must occur in the combustion chamber earlier in the cycle. If the engine is idling, the spark must occur just before the piston reaches TDC. At low speed, the spark has enough time to ignite the compressed airfuel mixture. However, at higher speeds, the spark must occur earlier. The spark must be given enough time to ignite the mixture. Without this spark advance, the piston would be up over TDC and moving down before the combustion pressure reaches a maximum. As a result the piston would keep ahead of the pressure rise. A weak power stroke would result. The action of centrifugal-advance mechanism causes the contact points to open and close earlier. Therefore, the ignition coil produces high voltage surge earlier and and the spark appear earlier in the combustion chamber Limitations of conventional ignition system The major limitations of the breaker-operated induction-coil system are the decrease in available voltage as engine speed increases due to decreasing time available to build up the primary coil stored energy. In addition to this, the breaker points are subjected electrical and mechanical wear, which results in short maintenance interval. 69

76 4.8.3 Electronic ignition system To eliminate the limitations of conventional ignition system, electronic ignition system is used electronic ignition system is widely used. The basic difference between the contactpoint and electronic ignition system is in the primary circuit. The primary circuit in the contact-point is opened and closed by contact points. In electronic system, the primary circuit is opened and closed by electronic control unit (ECU). For example, the distributor points and cam assembly of the conventional ignition system are replaced by a magnetic pulse generating system which detects the distributor shaft position and sends electrical pulses to an electronic control unit. The unit switches off the flow of current to the coil primary windings, inducing the high voltage in the secondary windings which is distributed to the spark plugs as in the conventional breaker system. With the help of electronic ignition system, maintenance of ignition system is reduced; spark plug life is extended and ignition of lean and dilute mixtures is improved Compression ignition engine In a compression ignition engine, self-ignition of the air-fuel mixture is a necessity. The correct fuel must be chosen which will self-ignite at the precise proper time in the engine cycle. It is therefore necessary to have knowledge and control of the ignition delay time of the fuel. The property that quantifies this is called the Cetane number. Fuel is injected by the fuel-injection system into the engine cylinder toward the end of the compression stroke, just before the desired start of combustion. The liquid fuel, usually injected at high velocity as one or more jets through small orifices or nozzles in the injector tip, atomizes into small drops and penetrates into the combustion chamber. The fuel vaporizes and mixes with the high-temperature high-pressure cylinder air. Since the air temperature and pressure are above the fuel's ignition point, spontaneous ignition of portions of the already-mixed fuel and air occurs. The cylinder pressure increases as combustion of the fuel-air mixture occurs. The consequent compression of the unburned portion of the charge shortens the delay before ignition for the fuel and air which has mixed to within combustible limits, which then bums rapidly. It also reduces the evaporation time of the remaining liquid fuel. Injection continues until the desired amount of fuel has entered the cylinder Types of diesel combustion system Based on combustion chamber design, diesel engine is divided into two categories, direct injection (DI) engine which have single open combustion chamber into which fuel is injected directly; and indirect injection (IDI) engine in which combustion chamber is divided into two regions and the fuel is injected into the pre-chamber which is connected to main chamber via nozzle. IDI design engines are only used in small engine sizes. 70

77 4.8.6 Fuel injector characteristics Fuel is introduced into the cylinder of the diesel engine through the nozzle in fuel injector. There is very high pressure differential across the nozzle which enables the fuel to penetrate through the pressurized air. The cylinder pressure at injection is generally in the range of atm. Fuel injection pressure is in the range of atm are used depending on the engine size and type. These large pressure differences across the injector nozzle are required so that injected liquid fuel jet will enter the chamber at sufficiently high velocity to (i) atomize into small sized droplets to enable rapid evaporation and (ii) traverse the combustion chamber in the time available and fully utilize the air charge. The task of fuel injector is to meter appropriate quantity of fuel for the given speed and load to each cylinder and inject fuel at the appropriate time. To accomplish this task, fuel is usually drawn from the fuel tank by a supply pump, and forced through a filter to the injection pump. The injection pump sends fuel under pressure to the nozzle pipes which carry fuel to the injector nozzles located in each cylinder head. Excess fuel goes back to the fuel tank. 4.9 Engine cooling system The purpose of the cooling system is to keep the engine at its most efficient operating temperature at all speeds and under all operating conditions. During the combustion of the air-fuel mixture in the cylinder, temperature of 2200 C or higher may be reached by the burning gases. At such high temperature the metals will their characteristics and piston will expand considerably and seize the liner. Of course theoretically thermal efficiency of the engine will improve without cooling but actually the engine will seize to run. Cylinder wall temperature must not go higher than about 200 to 260 C. Temperature higher than this causes the lubricating oil film to break down and lose its lubricating properties. The cooling system removes excess heat when the engine is hot and slowly or not at all when the engine is cold or warming up. Generally, cooling systems are designed to remove about 30 to 35% of heat produced in the combustion chamber by the burning of air-fuel mixture. Two general types of cooling systems are used in heat engines: air cooled and liquid cooled Air cooled In this method, heat is carried away by the air flowing over and around the engine cylinder. Fins and flanges on the outer surface of the cylinder are used to increase the exposed area to cooling air which raises the cooling rate. The common applications of air cooled engine are motorcycles and airplanes. In this type of cooling, the cylinders are semi-independent. They are not grouped in a block so the cylinder design is simpler and light. The main disadvantage of air cooling is non uniform cooling of cylinder especially for multiple cylinders Liquid cooled In the liquid cooling system, a liquid (generally water) is circulated around the cylinders to absorb heat form the cylinder walls. The liquid water to which an antifreeze solution and corrosion inhibitor is added is called coolant. The coolant absorbs heat as it passes through 71

78 the engine. Then the hot coolant is passed on to air that flowing through the radiator. The cooled coolant is then passed to the engine. The circulation of coolant continuously removes heat form the engine. The major components of liquid cooling are: Figure 4-2 Liquid cooling in engine Water Jacket: Water jacket is designed to keep the cylinder block and cylinder head cool. The water jacket is open space between the outside wall of the cylinder and the inside of the cylinder block and head. Water pump: Water pump is impeller-type centrifugal pumps. The driving force for the pump is taken from the engine shaft. Coolant from the radiator is drawn into the pump and sent to the engine block. Engine fan: The fan is driven by the same belt that drives pump. The purpose of fan is to pull air through radiator. This improves cooling at slow speeds and idle. At higher speeds, the air rammed through the radiator by the forward motion of the vehicle provides al the cooling air that is needed. Radiator: In the cooling system, the radiator is a heat exchanger that removes heat form coolant passing through it. The radiator holds a large volume of coolant in close contact with a large volume of air so that heat will transfer from the coolant to the air. 72

79 Figure 4-3 Radiator Thermostat: Thermostat is placed in the coolant passage between the cylinder head and the top of the radiator. Its purpose is to close off this passage when the engine is cold. Radiator pressure cap: The cooling systems on engines today are sealed pressurized by a radiator pressure cap. There are two advantages to sealing and pressurizing the cooling system. First, the increased pressure raises the boiling point of the coolant. Second, sealing the cooling system reduces coolant looses form evaporation. Antifreeze solution: If water freezes in the engine cooling system, it stops coolant circulation thus some part of the engine will overheat. On the other hand, water expands while freezing. Water freezing in the cylinder block and head could expand enough to crack the block or head. Water freezing in the radiator could split the radiator tubes. To prevent freezing of the water in the cooling system, antifreeze is added to form the coolant. Some antifreeze compounds plug small leaks in the cooling system. Corrosion inhibitor: Corrosion shortens the life of metal parts. Also, corrosion forms an insulating layer which reduces the amount of heat transferred from the metal part to the coolant. So corrosion inhibitor is also added in anti-freeze solution Advantage of liquid cooling Compact design of engine The fuel consumption of high compression liquid cooled engine is rather than for air cooled one. Uniform cooling 73

80 Engine can be installed anywhere since cooling system can be conveniently located wherever required where as air cooled engine requires it to be installed in the frontal area. The size of the engine does not involve serious problem as far as design of cooling system is concerned. In case of air cooled engines particularly in high power range difficulty is encountered in circulation of required quantity of air for cooling purpose Disadvantage of liquid cooling This is dependent system in which supply of water for circulation in the jacket is required. Power is absorbed by the pump and radiator fan. In the event of failure of cooling system serious damage may be caused to the engine. Cost of system is considerably high. Requires continuous maintenance Advantage of air cooling Simpler design due to absence of water jacket Simpler cooling system due to absence of pipes, fan and radiator assembly Easier installation No problem of freezing 4.13 Disadvantage of air cooling Non-uniform cooling The output of air cooled engine is less than that of a liquid cooled engine Smaller useful compression ratio 4.14 Engine lubricating system Engine lubricating system supplies lubricating oil to all engine moving parts. The lubricant and lubricating system function can be summarized as follow: 1. Protection of the engine against the wear. 2. Minimization of the frictional resistance of the engine to a minimum to ensure maximum mechanical efficiency. 3. Cooling the piston and region of the engine where friction work is dissipated. 4. The clearance between bearings and rotating journals are filled with oil. When heavy loads are suddenly imposed on the bearings, the oil helps to cushion the load. This reduces the bearing wear. 74

81 5. Forming a gas tight seal between piston rings and cylinder walls. 6. Removing all impurities form lubricated regions Desired property of lubricants Oxidation Stability: The lubricating oil subjected to atmospheric oxygen and high temperature, through oxidation, contribute to deposit formation. These deposits would eventually lead to ring sticking. Anti-oxidant and anti corrosive additives are used to control these problem. Detergency/Dispersion: The function of detergent additive is to reduce the amount of deposits formed and make their removal. It loosens and detaches particles of carbon and grit form engine parts and carry then down to the oil pan as oil circulates. Wear Reduction: Wear is due to the individual and combined effects of corrosion, adhesive and abrasion. Corrosive wear is effectively prevented by the use of detergent oils which neutralize the corrosive acids as they form. Oils with anti-wear additives and low viscosity at low temperature provide a remedy. Abrasion result form the presence of atmospheric dust, and metallic derbies from corrosive and adhesive wear, in the lubricating oil. Efficient air filtration is therefore most important. Elimination of abrasive particle impurities form the oil system by filtration and periodic oil change is essential. Viscosity: Oil viscosity is the most important parameter of lubricating oil. There are several grade of viscosity oil. They are rated for winter, for other than winter and for both purpose. For example SAE 20W is rated as winter use oil. SAE stands for Society for Automotive Engineers and W stands for winter. For other than winter use, the rating is given as SAE20. Higher the number higher is the viscosity of the oil. Now day multiple-viscosity oil is used. For example multiple viscosity oil or multi grade oil is graded as SAE 10W-30. This means that oil is same as SAE 10W when cold and SAE 30 when hot. Sludge formation Sludge is a thick, creamy, black substance that sometimes forms in the crankcase. It clogs oil screens and oil lines, preventing oil circulation. Water is collected in crankcase by combustion byproduct and the air. During cold operation the moisture condensates into water and gets deposited into the oil. The crankcase mixes the water, oil and carbon deposits continuously to form black thick substance called sludge. If the engine is run for long time, the water gets evaporated and leaves through the crank case ventilation but when the engine is used for short trip the water does not get enough time to evaporate and hence sludge forms Low pressure splash lubricating system The crankcase is used as the oil sump (reservoir) in a splash system, and the crankshaft rotating at high speed in the oil distributes it to the various moving parts by splash; no oil pump is used. All components, including the valve train and camshaft, must be open to the 75

82 crankcase. Oil is splashed into the cylinders behind the pistons acting both as a lubricant and a coolant. Many small four-stroke cycle engines (lawn mowers, golf carts, etc.) use splash distribution of oil High pressure distribution system An engine with a pressurized oil distribution system uses an oil pump to supply lubrication to the moving parts through passages built into the components. A typical automobile engine has oil passages built into the connecting rods, valve stems, push rods, rocker arms, valve seats, engine block, and many other moving components. These make up a circulation network through which oil is distributed by the oil pump. In addition, oil is sprayed under pressure onto the cylinder walls and onto the back of the piston crowns. Most automobiles actually use dual distribution systems, relying on splash within the crankcase in addition to the pressurized flow from the oil pump. 76

83 Chapter 5. Reciprocating air compressor 5.1 Reciprocating compression The air compression process in reciprocating air compressor (clearance volume is neglected in this case) involves the following steps (Fig. 5-1): a. Induction of air When piston moves from TBC to BDC, partial vacuum is created in the space above the piston. The pressure at inlet manifold is at atmospheric level so the inlet valve is pushed by higher pressure outside the valve. The pressure at delivery manifold is high because of the high pressure in storage tank. The high delivery manifold pressure closes the delivery valve. When the piston reaches BDC, the cylinder space is filled with air. It is assumed that the induction of the air occurs at constant pressure. TDC BDC TDC BDC TDC BDC P P P P 2 P 1 P 1 P 1 Piston moves from TDC to BDC. Air enters the cylinder at atm pressure v The air is compressed until the delivery valve is open v v Once the pressure inside the cylinder reaches the delivery pressure, delivery valve gets open and compressed air is delivered to the storage tank Fig. 5-1 Working principle of reciprocating air compressor b. Compression of air The piston moves from BDC to TDC. The compression of the air inside the cylinder starts. The volume decreases and the pressure increases. The increased pressure closes the inlet valve but it is still not sufficient to open the delivery valve since delivery manifold pressure is still higher. With the both valves closed, the air is compressed polytropically inside the cylinder 77

84 c. Delivery of air As the pressure inside the cylinder increases and reaches the delivery pressure, it is sufficient to open the delivery valve. Now the piston forces the compressed air out of the compressor to the storage tank. 5.2 Work done in compressor P-v diagram of the compressor without clearance is shown in Fig We can express the total work transfer during the air compressor cycle as the sum of work transfer in each process. Fig. 5-2 P-v diagram of reciprocating air compressor without clearance volume Total work done in the cycle = = Since, v4 and v3 = 0 for zero clearance volume = + = 1 = = 1 1 Eq. 5.1 Since the process 1-2 is polytropic = = / 78

85 = / Substituting Eq. 5.1 = 1 / 1 = / 1 = 1 / 1 Eq. 5.2 We know that an air compressor is driven by energy from external means. The sign convention that we adopt for work input in the system is negative. Therefore, the work transfer is negative in the air compressor. However, our interest is only on the amount of work/energy required in the compressor, we can eliminate the negative sign from our equation. If we only consider the magnitude of the work, we can express the work required for a reciprocating air compressor with zero clearance volume as, = 1 / 1 Eq. 5.3 Where, n = polytropic index of compression P1 = Intake pressure of air (Suction pressure) P2 = Delivery pressure of compressor v1 = Volume of air drawn inside the compressor during suction (swept volume) If swept volume is termed as vs, we can further express the equation for the work required in compressor as: OR = 1 / 1 Eq. 5.4 = 1 / 1 Eq. 5.5 OR (in extensive term) = 1 / 1 Eq

86 5.3 Isothermal compression We cannot use above equation when compression process is isothermal (n = 1). If the compression process follows isothermal law (n = 1), work required for the compressor can be expressed as = = + ln = + ln (since P1v1 = P2v2) = + ln = ln = ln = ln If only magnitude of the work required is considered OR = ln Eq. 5.7 = ln Eq. 5.8 OR (in extensive term) = ln Eq Effect of polytropic index on work required We have already discussed that the compression of air in a reciprocating air compressor is a polytropic process. From the Eq. 5.3, we can say that the work required also depends on the polytropic index. If the suction pressure, the delivery pressure and the swept volume are same and only the value of polytropic index is different, we can have the following cases: n > γ (=1.4 for air) n = γ (Adiabatic compression) 1<n < γ n = 1(Isothermal compression) We also know that inclination of curve Pv n = constant increases as the value of n increases. The P-v diagram for above four cases will be as shown in Fig

87 Process 1-2 for n > γ (=1.4 for air) Process 1-2 for n = γ (Adiabatic compression) Process 1-2 for 1<n < γ Fig. 5-3 Effect of polytropic index Process 1-2 for n = 1(Isothermal compression) We also know that area bounded by a cycle in P-v coordinate system represents the work transfer. In Error! Reference source not found., the area bounded by the cycle is the work required for the reciprocating air compressor. When we compare the area enclosed by the cycle for different value of n, we come to know that work required is the least when the compression is isothermal (area enclosed between ). As the value of n increases, the area enclosed increases and thus the work required also increases. In actual practice, it is impossible to achieve isothermal compression. But an attempt is made to achieve the value of n as close to 1 as possible. To get the compression as close to isothermal, the compressor is cooled by air or by any other cooling medium like water. 5.5 Compression process in T-s diagram The four different compression processes can be shown in T-s diagram as shown in the figure. Fig. 5-4 Compression process in T-s diagram 81

88 In the Fig. 5-4 path -2 represents isothermal compression (n = 1), path 1-2 represents polytropic compression (1 < n < γ), path 1-2 represents isentropic compression (n = γ) and finally path 1-2 represents polytropic compression with polytropic index n> γ. 5.6 Clearance volume effects, P-v diagram and work done So far, in the previous section we discussed about the air compressor without clearance volume. In actual scenario, it is impossible to have zero clearance space. In this section, the effects of clearance volume in operating parameters of reciprocating air compressor will be discussed. Fig. 5-5 Compression with clearance volume As shown in the Fig. 5-5 the compressor has clearance volume vc above the TDC. The piston cannot move past TDC and only moves between TDC and BDC. The volume contained between TDC and BDC is called displacement volume (vd). Displacement volume is the volume covered by the piston while moving between TDC and BDC. The fundamental working principle of compressor with or without clearance volume is almost similar. In former case, during the delivery of air (process 2-3) some amount of air is left in the clearance volume since piston cannot move beyond TDC. The residual air in the clearance volume has pressure P2 (delivery pressure). When the piston returns back to BDC from TDC, the air left in clearance volume expands polytropically (process 3-4). During the expansion process, the pressure inside the cylinder is higher than atmospheric pressure. The higher inside pressure prevents the inlet valve from getting open. As the inlet value is still closed, the air from atmosphere cannot be drawn inside the cylinder. When the pressure finally drops to P1 (suction pressure), the inlet valve opens and air is drawn inside the compressor. So suction of air only starts from point 4 and ends at point 1. Here we 82

89 should note that the displacement volume of the compressor is vd while the volume of air drawn in the cylinder is vs (often called effective swept). Now we can conclude that when clearance volume of the compressor is not zero, the volume of air drawn in the compressor is less than the actual cylinder capacity of the compressor. 5.7 Work done in single stage compressor with clearance volume The P-V diagram as shown in Fig. 5-5can be divided as in Fig Fig. 5-6 P-v diagram of compressor with clearance volume P-v diagram in Fig. 5-6 is same as that of compressor when clearance volume is neglected as discussed in section 5.4. So work done in compressor with clearance volume can be written as w = w1 w2 Where, w1 and w2 can be written in the form of Eq. 5.3 = 1 / 1 1 / 1 = 1 / = 1 / 1 = 1 1 / = 1 / 1 Eq Alternatively, the above expression can be derived as follow: From the Fig. 5-6, work can be calculated as = =

90 = Since, P2= P3 and P1 = P4 = = = = 1 + = 1 + = 1 1 Eq From the Fig. 5-6 we know that v1 - v4 = vs And, for compression and expansion process = = = = 1 = 1 = = = / = / Substituting in Eq = 1 / 1 =

91 = 1 / 1 Which is same as Eq If indices of compression and expansion are different, the equation for work required can be written as = 1 / 1 1 / 1 Eq Where, m is index of expansion and n is index of compression 5.8 Volumetric and adiabatic efficiencies For a compressor with clearance volume, the volume of air induced during the suction is less than the displacement volume of the compressor. To establish the relation between volume of cylinder and the actual volume of air coming in the compressor, volumetric efficiency of the compressor is established. The volumetric efficiency of an air compressor is defined as the ratio of volume of air induced in the cylinder to the displacement volume of the cylinder. Mathematically, = h h Let us define another term called clearance factor (C) such that C = vc/vd Since, = Eq = = + Eq For polytropic expansion process 3-4 = = = = Substituting in Eq

92 = + = 1 + Eq Adiabatic efficiency of an air compressor is defined as = 1 + Eq Effect of delivery pressure on the performance of air compressor The performance of a reciprocating air compressor varies significantly with the increase in delivery pressure. The effect of delivery pressure on the performance of an air compressor can be explained with the help of Fig. 5-7 Let us take a compressor with clearance volume vc and displacement volume vd. The suction pressure is P1. Initially the compressor is run to deliver the air at pressure P2. In this case, we can draw a cycle as (Fig. 5-7). The volume of air delivered for delivery pressure P2 is vs1 (v1 v4). Fig. 5-7 Effect of delivery pressure 86

93 If we increase the delivery pressure to P3, the cycle will be Since clearance volume is fixed for a given compressor size, the volume of air trapped in clearance volume will be same even we increase the pressure. For the delivery pressure P3, the volume of air delivered is vs2 (v1-v4 ). If we further increase delivery pressure to P4, from the Fig. 5-7 we can say that all the air is compressed in clearance space at the end of compression. As the air left in clearance volume cannot get out of outlet valve, there is no delivery of air when delivery pressure is P4. When the piston moves back to BDC, all the air left in clearance volume expands. The expansion process follows same path followed by compression process (1-2 -1). At the end of expansion (state 1), the air left in clearance volume occupies the cylinder which prevents additional air to enter from atmosphere to the cylinder. From above three cases, we can say that, for same intake condition, if delivery pressure is increased, the volumetric efficiency of the compressor will be decreased. If we keep on increasing the delivery pressure, at some point there will be a case where volumetric efficiency of the compressor will be zero i.e., no air is delivered Multi-stage compression Multistage compression is a serial arrangement of compressor cylinders in which compressed air from the one cylinder is fed to the next cylinder for the further compression. An intercooler is connected between two compressors, which cools the compressed air coming from low pressure compressor and supplies to high pressure compressor. Fig. 5-8 Two stage compression Intercooling Intercooler is a type of heat exchanger which is fitted between low pressure compressor and high pressure compressor. It cools the compressed air delivered by low pressure compressor. The cooled air is then passed to the high pressure compressor for the further 87

94 compression. The ideal intercooler (or perfect intercooler) should satisfy the flowing condition. The air is cooled at constant pressure. The temperature of the cooled air is same as the temperature of the air at the start of compression in low pressure compressor Representation of P-v and T-s diagram The P-v and T-s diagram of double stage compressor fitted with perfect intercooler is shown in the Fig The clearance volume is neglected in this case. The low pressure compressor compress the air from P1 (state 1) to P2 (state 2). The compressed air is then cooled in perfect intercooler from state 2 to state 2. During the cooling process, the pressure is constant at P2. The temperature of cooled air is equal to the temperature of the air at the start of compression (state 1 and 2 are in the isothermal curve). The air received from the intercooler is further compressed to P3 (state 3) in the high pressure compressor. P-v diagram of double stage compression Compression process in T-s diagram Fig. 5-9 P-v and T-s diagram of double stage compressor From the P-v diagram show in the Fig. 5-9, we can say that is the path followed by compression process in two stage air compressor fitted with perfect intercooler. If the intercooler is not included, the path followed by the compressor process will be The shift of compression from process 2-3 to process 2-3 is only due to the intercooling of air. From the P-v diagram in the Fig. 5-9, we can say that due to the shift in the compression process, work as represented by the shaded area is saved. In other word, with intercooler, we need less work to compress the air compared to without intercooler. So, we can say that the multistage compression process is efficient when intercoolers are used in between the compressors. The work required to compress in above case will be 88

95 = + From Eq. 5.4, we have = Since, 1 and 2 state are in same isothermal line for a perfect intercooling = So we have, = = Eq Optimum pressure distribution work done In the previous section, we discussed about the two stage compressor where low pressure compressor rises the pressure of air up to certain level and then high pressure compressor further compresses the air up to delivery pressure. In the following section, we will discuss about how the pressure should be distributed between the low pressure compressor and the high pressure compressor so that minimum required work is achieved. Total work required in two stage compressor with perfect intercooler is (from Eq. 5.17) = 1 / + / 2 Since the induction pressure P1 and delivery pressure P3 are fixed, we can only change intermediate pressure P2 to obtain the minimum work required. For the work to be minimum, the first derivative of the expression of work with respect to P2 must be zero. = / / / + / 2 = 0 + / 2 = 0 / / = 0 89

96 1 1 / 1 1 / / = 1 1 / / = 1 1 / 1 / / = 1 / 1 / / = / / = / = / = = Eq Eq is the condition for optimum pressure distribution in two stage compressor. Substituting in Eq. 5.17, we have = 1 / = 1 / + / 2 + / 2 = 1 / + / 2 = 2 1 / 1 = 2 1 / 1 Eq This is the required expression for work required in two stage air compressor with perfect intercooler and optimum pressure distribution. For the pressure distribution in multistage (N-stage) compression process, Eq can be written as = = = = Eq Similarly work required in multi stage (N-stage) compressor is: 90

97 = 1 / 1 Eq Positive displacement compressor Positive displacement compressors are those compressors in which air is compressed by being trapped in the reduced space formed by two sets of engaging surfaces. This type of compressor deliver fixed volume of air at high pressure. Positive displacement machines ensure positive admission and delivery preventing undesired reversal of flow. For example, reciprocating compressor, root blower, rotary screw compressor Axial flow compressor An axial flow compressor is one in which the flow enters the compressor in an axial direction (parallel with the axis of rotation), and exits in an axial direction. The axial-flow compressor compresses its working fluid by first accelerating the fluid and then diffusing it to obtain a pressure increase. The air is accelerated by a row of rotating airfoils (blades) called the rotor, and then diffused in a row of stationary blades (the stator). The diffusion in the stator converts the velocity increase gained in the rotor to a pressure increase. Axial flow compressors produce a continuous flow of compressed air, and have the benefits of high efficiencies and large mass flow capacity. Axial compressors are widely used in gas turbines, such as jet engines, high speed ship engines, and small scale power stations. In an axial flow compressor, air passes from one stage to the next, each stage raising the pressure slightly. By producing low pressure increases on the order of 1.1:1 to 1.4:1, very high efficiencies can be obtained. The use of multiple stages permits overall pressure increases of up to 40:1 in some aerospace applications and a pressure ratio of 30:1 in some Industrial applications. Front part of axial compressor Position of rotor and stator Fig Axial flow compressor Roots blower The Roots type compressor (supercharger) or Roots blower is a positive displacement lobe pump which operates by pumping air with a pair of meshing vanes (lobes). The roots type compressor is two counter-rotating meshed lobed rotors. The two rotors trap air in the gaps between rotors and push it against the compressor housing as they rotate towards the 91

98 outlet/discharge port. During each rotation, a specific fixed amount of air is trapped and moved to the outlet port where it is compressed, which is why the roots type compressor falls under the broader category of fixed-displacement superchargers. Roots blowers are typically used in applications where a large volume of air must be moved across a relatively small pressure differential. This includes low vacuum applications, with the Roots blower acting alone, or use as part of a high vacuum system, in combination with other pumps. Two lobe and three lobe type roots blower are shown in the Fig Three lobe root blower Two lobe root blower Fig Root blower Rotary compressor A rotary compressor, or rotary vane compressor, is a device used for moving a fluid through a system. A rotary vane compressor has a central, spinning rotor and a number of vanes. The rotor assembly is encased inside of a sealed container with an inlet and outlet valve. The vanes are spring-loaded so that they constantly push against the outside of the case, creating a tight seal. Fig Rotary compressor The rotor is offset to one side. When a rotary blade spins past the inlet valve, it creates a vacuum. The air flows out of the valve behind it, filling the vacuum. As it approaches the outlet valve, the chamber shrinks. This creates more pressure on the air. The air has nowhere to go but out of the outlet valve, so it shoots out of it. Then the vane continues on to draw more air at the inlet valve. Common uses of vane pumps include high pressure hydraulic pumps and automotive uses 92

Process 1-2: Reversible adiabatic compression process. Process 2-3: Reversible isothermal heat addition

Process 1-2: Reversible adiabatic compression process. Process 2-3: Reversible isothermal heat addition Vapor Power Cycles Process 1-2: Reversible adiabatic compression process from P1 to P2. Process 2-3: Reversible isothermal heat addition process at constant temperature TH. Process 3-4: Reversible adiabatic

More information

CHAPTER I GAS POWER CYCLES

CHAPTER I GAS POWER CYCLES CHAPTER I GAS POWER CYCLES 1.1 AIR STANDARD CYCLES Air standard cycles are used for comparison of thermal efficiencies of I.C engines. Engines working with air standard cycles are known as air standard

More information

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions

L34: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Introduction to Gas Cycles Definitions Page L: Internal Combustion Engine Cycles: Otto, Diesel, and Dual or Gas Power Cycles Review of Carnot Power Cycle (gas version) Air-Standard Cycles Internal Combustion (IC) Engines - Otto and Diesel Cycles

More information

USO4CICV01/US04CICH02:

USO4CICV01/US04CICH02: Natubhai V. Patel College of Pure & Applied Sciences S. Y. B.Sc. Semester-4 Industrial chemistry/ IC (Vocational) USO4CICV0/US04CICH02: Chemical Plant Utilities UNIT 5 Internal combustion engine In an

More information

(v) Cylinder volume It is the volume of a gas inside the cylinder when the piston is at Bottom Dead Centre (B.D.C) and is denoted by V.

(v) Cylinder volume It is the volume of a gas inside the cylinder when the piston is at Bottom Dead Centre (B.D.C) and is denoted by V. UNIT II GAS POWER CYCLES AIR STANDARD CYCLES Air standard cycles are used for comparison of thermal efficiencies of I.C engines. Engines working with air standard cycles are known as air standard engines.

More information

ME2301 THERMAL ENGINEERING L T P C OBJECTIVE:

ME2301 THERMAL ENGINEERING L T P C OBJECTIVE: ME2301 THERMAL ENGINEERING L T P C 3 1 0 4 OBJECTIVE: To integrate the concepts, laws and methodologies from the first course in thermo dynamics into analysis of cyclic processes To apply the thermodynamic

More information

Internal Combustion Engines

Internal Combustion Engines Internal Combustion Engines Reading Problems 8-3 8-7 8-35, 8-45, 8-52 Definitions 1. spark ignition: a mixture of fuel and air is ignited by a spark plug applications requiring power to about 225 kw (300

More information

MEB THERMAL ENGINEERING - I QUESTION BANK UNIT-I PART-A

MEB THERMAL ENGINEERING - I QUESTION BANK UNIT-I PART-A MEB 420 - THERMAL ENGINEERING - I QUESTION BANK UNIT-I Each question carries 1 mark. PART-A 1. Define temperature. 2. Define intensive property 3. Explain the term absolute zero of temperature 4. State

More information

In this lecture... Gas power cycles

In this lecture... Gas power cycles 7 Lect-7 Gas power cycles In this lecture... he Carnot cycle and its significance Air-standard assumptions An oeriew of reciprocating engines Otto cycle: the ideal cycle for sparkignition engines Diesel

More information

(a) then mean effective pressure and the indicated power for each end ; (b) the total indicated power : [16]

(a) then mean effective pressure and the indicated power for each end ; (b) the total indicated power : [16] Code No: R05220304 Set No. 1 II B.Tech II Semester Regular Examinations, Apr/May 2007 THERMAL ENGINEERING-I ( Common to Mechanical Engineering and Automobile Engineering) Time: 3 hours Max Marks: 80 Answer

More information

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE

VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE VALVE TIMING DIAGRAM FOR SI ENGINE VALVE TIMING DIAGRAM FOR CI ENGINE Page 1 of 13 EFFECT OF VALVE TIMING DIAGRAM ON VOLUMETRIC EFFICIENCY: Qu. 1:Why Inlet valve is closed after the Bottom Dead Centre

More information

2013 THERMAL ENGINEERING-I

2013 THERMAL ENGINEERING-I SET - 1 II B. Tech II Semester, Regular Examinations, April/May 2013 THERMAL ENGINEERING-I (Com. to ME, AME) Time: 3 hours Max. Marks: 75 Answer any FIVE Questions All Questions carry Equal Marks ~~~~~~~~~~~~~~~~~~~~~~~~

More information

Combustion engines. Combustion

Combustion engines. Combustion Combustion engines Chemical energy in fuel converted to thermal energy by combustion or oxidation Heat engine converts chemical energy into mechanical energy Thermal energy raises temperature and pressure

More information

GYANMANJARI INSTITUTE OF TECHNOLOGY (GMIT) SUBJECT: ELEMENTS OF MECHANICAL ENGINEERING Assignment Ch 1

GYANMANJARI INSTITUTE OF TECHNOLOGY (GMIT) SUBJECT: ELEMENTS OF MECHANICAL ENGINEERING Assignment Ch 1 1. 3. GYANMANJARI INSTITUTE OF TECHNOLOGY (GMIT) Assignment Ch 1 A steel ball having mass of 10 kg and a specific heat of 460 J/kg K is heated from 50 o C to 200 o C. Determine the heat required. In a

More information

Chapter 8 Production of Power from Heat

Chapter 8 Production of Power from Heat Chapter 8 Production of Power from Heat Different sources of power, such as solar energy (from sun), kinetic energy from atmospheric winds and potential energy from tides. The most important source of

More information

Comparative Study Of Four Stroke Diesel And Petrol Engine.

Comparative Study Of Four Stroke Diesel And Petrol Engine. Comparative Study Of Four Stroke Diesel And Petrol Engine. Aim: To study the construction and working of 4- stroke petrol / diesel engine. Theory: A machine or device which derives heat from the combustion

More information

Noble Group of Institutions, Junagadh. Faculty of Engineering Department of Mechanical Engineering

Noble Group of Institutions, Junagadh. Faculty of Engineering Department of Mechanical Engineering Semester:1 st Subject: Elements of Mechanical Engineering (2110006) Faculty: Mr. Ishan Bhatt Year: 2017-18 Class: Comp. & IT Ele TUTORIAL 1 INTRODUCTION Q.1 Define: Force, Work, Pressure, Energy, Heat

More information

Idealizations Help Manage Analysis of Complex Processes

Idealizations Help Manage Analysis of Complex Processes 8 CHAPTER Gas Power Cycles 8-1 Idealizations Help Manage Analysis of Complex Processes The analysis of many complex processes can be reduced to a manageable level by utilizing some idealizations (fig.

More information

UNIT IV INTERNAL COMBUSTION ENGINES

UNIT IV INTERNAL COMBUSTION ENGINES UNIT IV INTERNAL COMBUSTION ENGINES Objectives After the completion of this chapter, Students 1. To know the different parts of IC engines and their functions. 2. To understand the working principle of

More information

Gas Power Cycles. Tarawneh

Gas Power Cycles. Tarawneh Gas Power Cycles Dr.Mohammad Tarawneh ) Carnot cycle 2) Otto cycle ) Diesel cycle - Today 4) Dual Cycle 5) Stirling cycle 6) Ericsson cycles 7) Brayton cycle Carnot Cycle Reversible isothermal expansion

More information

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING. Question Bank. UNIT-I THERMODYNAMIC CYCLES Part-A (2 Marks)

KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING. Question Bank. UNIT-I THERMODYNAMIC CYCLES Part-A (2 Marks) KINGS COLLEGE OF ENGINEERING DEPARTMENT OF MECHANICAL ENGINEERING Question Bank Sub. Code/Name: ME1351 - THERMAL ENGINEERING Year/Sem: III/VI 1. What is a thermodynamic cycle? UNIT-I THERMODYNAMIC CYCLES

More information

SET - 1 II B. Tech II Semester Regular/Supplementary Examinations, April/May-2017 THERMAL ENGINEERING-I (Mechanical Engineering) Time: 3 hours Max. Marks: 70 Note: 1. Question Paper consists of two parts

More information

Chapter 9 GAS POWER CYCLES

Chapter 9 GAS POWER CYCLES Thermodynamics: An Engineering Approach Seventh Edition in SI Units Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2011 Chapter 9 GAS POWER CYCLES Mehmet Kanoglu University of Gaziantep Copyright The McGraw-Hill

More information

Chapter 9 GAS POWER CYCLES

Chapter 9 GAS POWER CYCLES Thermodynamics: An Engineering Approach, 6 th Edition Yunus A. Cengel, Michael A. Boles McGraw-Hill, 2008 Chapter 9 GAS POWER CYCLES Copyright The McGraw-Hill Companies, Inc. Permission required for reproduction

More information

SIDDHARTH INSTITUTE OF ENGINEERING & TECHNOLOGY :: PUTTUR (AUTONOMOUS) QUESTION BANK UNIT I I.C ENGINES

SIDDHARTH INSTITUTE OF ENGINEERING & TECHNOLOGY :: PUTTUR (AUTONOMOUS) QUESTION BANK UNIT I I.C ENGINES SIDDHARTH INSTITUTE OF ENGINEERING & TECHNOLOGY :: PUTTUR UNIT I I.C ENGINES 1 (a) Explain any six types of classification of Internal Combustion engines. (6M) (b) With a neat sketch explain any three

More information

Thermodynamic Cycles. Alicia Ma. Esponda Cascajares

Thermodynamic Cycles. Alicia Ma. Esponda Cascajares Thermodynamic Cycles Alicia Ma. Esponda Cascajares Power Cycles Cycles which convert a heat input into a mechanical work output. Power cycles can be divided according to the type of heat engine they seek

More information

Engine Cycles. T Alrayyes

Engine Cycles. T Alrayyes Engine Cycles T Alrayyes Introduction The cycle experienced in the cylinder of an internal combustion engine is very complex. The cycle in SI and diesel engine were discussed in detail in the previous

More information

The Internal combustion engine (Otto Cycle)

The Internal combustion engine (Otto Cycle) The Internal combustion engine (Otto Cycle) The Otto cycle is a set of processes used by spark ignition internal combustion engines (2-stroke or 4-stroke cycles). These engines a) ingest a mixture of fuel

More information

Assignment-1 Air Standard Cycles

Assignment-1 Air Standard Cycles Assignment-1 Air Standard Cycles 1. What do u mean by air standard cycle? List assumptions for air standard cycle & give reasons why air standard cycle differs from actual cycle. 2. Derive an equation

More information

2. Discuss the effects of the following operating variables on detonation

2. Discuss the effects of the following operating variables on detonation Code No: RR220303 Set No. 1 II B.Tech II Semester Regular Examinations, Apr/May 2006 THERMAL ENGINEERING-I ( Common to Mechanical Engineering and Automobile Engineering) Time: 3 hours Max Marks: 80 Answer

More information

VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING ME6404 THERMAL ENGINEERING

VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING ME6404 THERMAL ENGINEERING VETRI VINAYAHA COLLEGE OF ENGINEERING AND TECHNOLOGY DEPARTMENT OF MECHANICAL ENGINEERING ME6404 THERMAL ENGINEERING UNIT I - GAS POWER CYCLES 1. What is a thermodynamic cycle? Thermodynamic cycle is defined

More information

Hours / 100 Marks Seat No.

Hours / 100 Marks Seat No. 17529 14115 3 Hours / 100 Seat No. Instructions (1) All Questions are Compulsory. (2) Answer each next main Question on a new page. (3) Illustrate your answers with neat sketches wherever necessary. (4)

More information

Gas Power System. By Ertanto Vetra

Gas Power System. By Ertanto Vetra Gas Power System 1 By Ertanto Vetra Outlines Introduction Internal Combustion Engines Otto Cycles Diesel Cycles Gas Turbine Cycles Gas Turbine Based Combined Cycles Gas Turbines for Aircrafts Turbojets

More information

Heat engine. Heat engine

Heat engine. Heat engine Heat engine Device that transforms heat into work. It requires two energy reservoirs at different temperatures An energy reservoir is a part of the environment so large wrt the system that its temperature

More information

UNIT 2 POWER PLANTS 2.1 INTRODUCTION 2.2 CLASSIFICATION OF IC ENGINES. Objectives. Structure. 2.1 Introduction

UNIT 2 POWER PLANTS 2.1 INTRODUCTION 2.2 CLASSIFICATION OF IC ENGINES. Objectives. Structure. 2.1 Introduction UNIT 2 POWER PLANTS Power Plants Structure 2.1 Introduction Objectives 2.2 Classification of IC Engines 2.3 Four Stroke Engines versus Two Stroke Engines 2.4 Working of Four Stroke Petrol Engine 2.5 Working

More information

η th W = Q Gas Power Cycles: Working fluid remains in the gaseous state through the cycle.

η th W = Q Gas Power Cycles: Working fluid remains in the gaseous state through the cycle. Gas Power Cycles: Gas Power Cycles: Working fluid remains in the gaseous state through the cycle. Sometimes useful to study an idealised cycle in which internal irreversibilities and complexities are

More information

Week 10. Gas Power Cycles. ME 300 Thermodynamics II 1

Week 10. Gas Power Cycles. ME 300 Thermodynamics II 1 Week 10 Gas Power Cycles ME 300 Thermodynamics II 1 Today s Outline Gas power cycles Internal combustion engines Four-stroke cycle Thermodynamic cycles Ideal cycle ME 300 Thermodynamics II 2 Gas Power

More information

Principles of Engine Operation. Information

Principles of Engine Operation. Information Internal Combustion Engines MAK 4070E Principles of Engine Operation Prof.Dr. Cem Soruşbay Istanbul Technical University Information Prof.Dr. Cem Soruşbay İ.T.Ü. Makina Fakültesi Motorlar ve Taşıtlar Laboratuvarı

More information

Chapter 9. Two important areas of application for thermodynamics GAS POWER CYCLES. Objectives

Chapter 9. Two important areas of application for thermodynamics GAS POWER CYCLES. Objectives Chapter 9 GAS POWER CYCLES Two important areas of application for thermodynamics are power generation and refrigeration. Both are usually accomplished by systems that operate on a thermodynamic cycle.

More information

SAMPLE STUDY MATERIAL

SAMPLE STUDY MATERIAL IC Engine - ME GATE, IES, PSU 1 SAMPLE STUDY MATERIAL Mechanical Engineering ME Postal Correspondence Course Internal Combustion Engine GATE, IES & PSUs IC Engine - ME GATE, IES, PSU 2 C O N T E N T 1.

More information

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5

Kul Internal Combustion Engine Technology. Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Kul-14.4100 Internal Combustion Engine Technology Definition & Classification, Characteristics 2015 Basshuysen 1,2,3,4,5 Definitions Combustion engines convert the chemical energy of fuel to mechanical

More information

Scheme G Sample Question Paper Course Name : Diploma in Automobile Engineering Course Code : AE

Scheme G Sample Question Paper Course Name : Diploma in Automobile Engineering Course Code : AE Sample Question Paper Semester : Fourth Marks : 100 Time: 03 Hours Q1.A. Attempt any SIX a. State different types of ideal gas processes 12 Marks b. Define dryness fraction and degree of superheat. c.

More information

Assignment-1 Introduction

Assignment-1 Introduction Assignment-1 Introduction 1. Compare S.I. engines with C.I engines. 2. Explain with the help of neat sketch, the working of a 2-stroke petrol engine. 3. Derive an equation of efficiency, work output and

More information

Unit WorkBook 4 Level 4 ENG U13 Fundamentals of Thermodynamics and Heat Engines UniCourse Ltd. All Rights Reserved. Sample

Unit WorkBook 4 Level 4 ENG U13 Fundamentals of Thermodynamics and Heat Engines UniCourse Ltd. All Rights Reserved. Sample Pearson BTEC Levels 4 Higher Nationals in Engineering (RQF) Unit 13: Fundamentals of Thermodynamics and Heat Engines Unit Workbook 4 in a series of 4 for this unit Learning Outcome 4 Internal Combustion

More information

Thermodynamics cycles can be classified into different categories depending on fluid used or the different processes:

Thermodynamics cycles can be classified into different categories depending on fluid used or the different processes: Classification of thermodynamics cycles Thermodynamics cycles can be classified into different categories depending on fluid used or the different processes: Gas and vapor cycles - Gas cycle: the working

More information

DEPARTMENT OF MECHANICAL ENGINEERING ME ENGINEERING THERMODYNAMICS TWO MARKS QUESTION AND ANSWER

DEPARTMENT OF MECHANICAL ENGINEERING ME ENGINEERING THERMODYNAMICS TWO MARKS QUESTION AND ANSWER DEPARTMENT OF MECHANICAL ENGINEERING ME 6301- ENGINEERING THERMODYNAMICS TWO MARKS QUESTION AND ANSWER 1. Define the term thermal engineering. Ans: Thermal engineering is the science that deals with the

More information

DEPARTMENT OF MECHANICAL ENGINEERING Question Bank ME THERMAL ENGINEERING. Part-A (2 Marks)

DEPARTMENT OF MECHANICAL ENGINEERING Question Bank ME THERMAL ENGINEERING. Part-A (2 Marks) DEPARTMENT OF MECHANICAL ENGINEERING Question Bank ME1351 - THERMAL ENGINEERING UNIT I GAS POWER CYCLES Part-A (2 Marks) 1. What is a thermodynamic cycle? 2. What is meant by air standard cycle? 3.. Name

More information

Scheme - G. Sample Test Paper-I. Course Name : Diploma in Mechanical Engineering Course Code : ME Semester : Fifth Subject Title : Power Engineering

Scheme - G. Sample Test Paper-I. Course Name : Diploma in Mechanical Engineering Course Code : ME Semester : Fifth Subject Title : Power Engineering Sample Test Paper-I Marks : 25 Time:1 hour Q1. Attempt any Three 3X3=9 a) Define i) Mean Effective Pressure ii) Piston Speed iii) Swept Volume b) Draw Carnot cycle on P-V and T-S Diagram c) State the need

More information

UNIT 1 GAS POWER CYCLES

UNIT 1 GAS POWER CYCLES THERMAL ENGINEERING UNIT 1 GAS POWER CYCLES Air Standard Cycles - Otto, Diesel, Dual, Brayton cycle with intercooling, reheating and regeneration- Calculation of airstandard efficiency and mean effective

More information

ME Thermal Engineering Question Bank

ME Thermal Engineering Question Bank ME2301 - Thermal Engineering Question Bank UNIT I GAS POWER CYCLES Otto, Diesel, Dual, Brayton cycles, Calculation of mean effective pressure, and air standard efficiency -Actual and theoretical PV diagram

More information

Chapter 6. Supercharging

Chapter 6. Supercharging SHROFF S. R. ROTARY INSTITUTE OF CHEMICAL TECHNOLOGY (SRICT) DEPARTMENT OF MECHANICAL ENGINEERING. Chapter 6. Supercharging Subject: Internal Combustion Engine 1 Outline Chapter 6. Supercharging 6.1 Need

More information

GAS POWER CYCLES. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University

GAS POWER CYCLES. Dr Ali Jawarneh Department of Mechanical Engineering Hashemite University Chapter 9 GAS POWER CYCLES Dr Ali Jawarneh Department of Mechanical Engineering i Hashemite University 2 Objectives Evaluate the performance of gas power cycles for which h the working fluid remains a

More information

Page 2. (a) (i) Show that during the change AB the gas undergoes an isothermal change.

Page 2. (a) (i) Show that during the change AB the gas undergoes an isothermal change. Q1.The Carnot cycle is the most efficient theoretical cycle of changes for a fixed mass of gas in a heat engine. The graph below shows the pressure volume (p V) diagram for a gas undergoing a Carnot cycle

More information

Introduction to I.C Engines CH. 1. Prepared by: Dr. Assim Adaraje

Introduction to I.C Engines CH. 1. Prepared by: Dr. Assim Adaraje Introduction to I.C Engines CH. 1 Prepared by: Dr. Assim Adaraje 1 An internal combustion engine (ICE) is a heat engine where the combustion of a fuel occurs with an oxidizer (usually air) in a combustion

More information

I.C ENGINES. CLASSIFICATION I.C Engines are classified according to:

I.C ENGINES. CLASSIFICATION I.C Engines are classified according to: I.C ENGINES An internal combustion engine is most popularly known as I.C. engine, is a heat engine which converts the heat energy released by the combustion of the fuel taking place inside the engine cylinder

More information

ENGINE & WORKING PRINCIPLES

ENGINE & WORKING PRINCIPLES ENGINE & WORKING PRINCIPLES A heat engine is a machine, which converts heat energy into mechanical energy. The combustion of fuel such as coal, petrol, diesel generates heat. This heat is supplied to a

More information

Important Instructions to examiners: 1) The answers should be examined by key words and not as word-to-word as given in the model answer scheme. 2) The model answer and the answer written by candidate

More information

OBJECTIVE: GENERAL ASPECTS ABOUT ENGINES MECHANISM:

OBJECTIVE: GENERAL ASPECTS ABOUT ENGINES MECHANISM: LANDMARK UNIVERSITY, OMU-ARAN LECTURE NOTE 3 COLLEGE: COLLEGE OF SCIENCE AND ENGINEERING DEPARTMENT: MECHANICAL ENGINEERING Course code: MCE 211 Course title: Introduction to Mechanical Engineering Credit

More information

Power Cycles. Ideal Cycles, Internal Combustion

Power Cycles. Ideal Cycles, Internal Combustion Gas Power Cycles Power Cycles Ideal Cycles, Internal Combustion Otto cycle, spark ignition Diesel cycle, compression ignition Sterling & Ericsson cycles Brayton cycles Jet-propulsion cycle Ideal Cycles,

More information

Prepared by: Dr. Assim Adaraje

Prepared by: Dr. Assim Adaraje Air-standard cycles Prepared by: Dr. Assim Adaraje CH. 2 ۱ Cold-air-standard assumptions: When the working fluid is considered to be air with constant specific heats at room temperature (25 C). Air-standard

More information

ENGINES ENGINE OPERATION

ENGINES ENGINE OPERATION ENGINES ENGINE OPERATION Because the most widely used piston engine is the four-stroke cycle type, it will be used as the example for this section, Engine Operation and as the basis for comparison in the

More information

Template for the Storyboard stage

Template for the Storyboard stage Template for the Storyboard stage Animation can be done in JAVA 2-D. Mention what will be your animation medium: 2D or 3D Mention the software to be used for animation development: JAVA, Flash, Blender,

More information

Comparison of Air-Standard Atkinson, Diesel and Otto Cycles with Constant Specific Heats

Comparison of Air-Standard Atkinson, Diesel and Otto Cycles with Constant Specific Heats Comparison of Air-Standard Atkinson, Diesel and Otto Cycles with Constant Specific Heats Sethi Upasna Vijay 1, Mansha Kumari 2 1 Assistant Professor, Mechanical Engineering Department, Vadodara Institute

More information

ACTUAL CYCLE. Actual engine cycle

ACTUAL CYCLE. Actual engine cycle 1 ACTUAL CYCLE Actual engine cycle Introduction 2 Ideal Gas Cycle (Air Standard Cycle) Idealized processes Idealize working Fluid Fuel-Air Cycle Idealized Processes Accurate Working Fluid Model Actual

More information

Internal Combustion Engine. Prepared by- Md Ferdous Alam Lecturer, MEE, SUST

Internal Combustion Engine. Prepared by- Md Ferdous Alam Lecturer, MEE, SUST Internal Combustion Engine Prepared by- Md Ferdous Alam Lecturer, MEE, SUST What is an Engine? -a machine designed to convert one form of energy into mechanical energy Two types of engines : 1. Internal

More information

Approved by AICTE, Government of India & affiliated to Dr. A.P.J. Abdul Kalam Technical University, Lucknow Department of Mechanical Engineering

Approved by AICTE, Government of India & affiliated to Dr. A.P.J. Abdul Kalam Technical University, Lucknow Department of Mechanical Engineering Experiment No. - 1 Object: Study and working of four stroke petrol engine. Apparatus Required: S. No. Name of Apparatus Specifications Model of Four stroke petrol engine NA Figure 1: Working of four stroke

More information

IC ENGINES. Differences between SI and CI engines: Petrol is fuel, which has a high self ignition temperature

IC ENGINES. Differences between SI and CI engines: Petrol is fuel, which has a high self ignition temperature IC ENGINES SI Engines work at constant volume. They have a compression ratio of around 6-10. But CI engines work at constant pressure and has a compression ratio of 16-20. In four stroke engines, one power

More information

Combustion Systems What we might have learned

Combustion Systems What we might have learned Combustion Systems What we might have learned IMechE ADSC, 6 December 2012 Chris Whelan Contents Engines Big & Small Carnot, Otto & Diesel Thermodynamic Cycles Combustion Process & Systems Diesel & Otto

More information

Internal Combustion Engines TUTORIAL

Internal Combustion Engines TUTORIAL Internal Combustion Engines TUTORIAL College of Engineering Mechanical Engineering Department Academic Year 2012-2013 Class 3 rd Year Class Subject Lecturer Internal Combustion Engines Dr. Raoof M. Radhi

More information

Content : 4.1 Brayton cycle-p.v. diagram and thermal efficiency. 4Marks Classification of gas turbines.

Content : 4.1 Brayton cycle-p.v. diagram and thermal efficiency. 4Marks Classification of gas turbines. Content : 4.1 Brayton cycle-p.v. diagram and thermal efficiency. 4Marks Classification of gas turbines. 4.2 Construction and working of gas turbines i) Open cycle ii) Closed cycle gas Turbines, P.V. and

More information

A REVIEW ON STIRLING ENGINES

A REVIEW ON STIRLING ENGINES A REVIEW ON STIRLING ENGINES Neeraj Joshi UG Student, Department of Mechanical Engineering, Sandip Foundation s Sandip Institute of Technology and Research Centre,Mahiravani, Nashik Savitribai Phule Pune

More information

UNIVERSITY POLYTECHNIC B.I.T., MESRA, RANCHI

UNIVERSITY POLYTECHNIC B.I.T., MESRA, RANCHI COURSE STRUCTURE SEMESTER V (Total Unit 7.0) Course Code Theory Unit Course Code Sessional Unit DMM 5001 Automobile Engineering 1.0 DMM 5002 Automobile Engineering 0.5 Lab. DMM 5003 CAD/CAM 1.0 DMM5004

More information

AT AUTOMOTIVE ENGINES QUESTION BANK

AT AUTOMOTIVE ENGINES QUESTION BANK AT6301 - AUTOMOTIVE ENGINES QUESTION BANK UNIT I: CONSTRUCTION & WORKING PRINCIPLE OF IC ENGINES 1. State the application of CI engines? 2. What is Cubic capacity of an engine? 3. What is the purpose of

More information

ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY

ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY 1 INTERNAL COMBUSTION ENGINES ADDIS ABABA UNIVERSITY INSTITUTE OF TECHNOLOGY MECHANICAL ENGINEERING DEPARTMENT DIVISON OF THERMAL AND ENERGY CONVERSION IC Engine Fundamentals 2 Engine Systems An engine

More information

Applied Thermodynamics Internal Combustion Engines

Applied Thermodynamics Internal Combustion Engines Applied Thermodynamics Internal Combustion Engines Assoc. Prof. Dr. Mazlan Abdul Wahid Faculty of Mechanical Engineering Universiti Teknologi Malaysia www.fkm.utm.my/~mazlan 1 Coverage Introduction Operation

More information

EEN-E2002 Internal Combustion Definitions and Characteristics, lecture 3. January 2017, Martti Larmi

EEN-E2002 Internal Combustion Definitions and Characteristics, lecture 3. January 2017, Martti Larmi EEN-E2002 Internal Combustion Definitions and Characteristics, lecture 3 January 2017, Martti Larmi Textbooks on Internal Combustion Internal combustion engine handbook : basics, components, systems, and

More information

8.21 The Physics of Energy Fall 2009

8.21 The Physics of Energy Fall 2009 MIT OpenCourseWare http://ocw.mit.edu 8.21 The Physics of Energy Fall 2009 For information about citing these materials or our Terms of Use, visit: http://ocw.mit.edu/terms. 8.21 Lecture 11 Internal Combustion

More information

Thermodynamics Third Law Heat Engines

Thermodynamics Third Law Heat Engines Thermodynamics Third Law Heat Engines Lana Sheridan De Anza College May 11, 2018 Last time heat engines heat pumps Carnot engines Overview efficiency of Carnot engines the Third Law real engines Heat Engine

More information

Government of Karnataka Department of Technical Education Board of Technical Examinations, Bangalore

Government of Karnataka Department of Technical Education Board of Technical Examinations, Bangalore CIE- 25 Marks Government of Karnataka Department of Technical Education Board of Technical Examinations, Bangalore Prerequisites: Knowledge of basic mathematics and Applied Science Course Objectives: 1.

More information

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING

COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COVENANT UNIVERSITY NIGERIA TUTORIAL KIT OMEGA SEMESTER PROGRAMME: MECHANICAL ENGINEERING COURSE: MCE 320 DISCLAIMER The contents of this document are intended for practice and leaning purposes at the

More information

Operating Characteristics

Operating Characteristics Chapter 2 Operating Characteristics 2-1 Engine Parameters 2-22 Work 2-3 Mean Effective Pressure 2-4 Torque and Power 2-5 Dynamometers 2-6 Air-Fuel Ratio and Fuel-Air Ratio 2-7 Specific Fuel Consumption

More information

Simple Finite Heat Release Model (SI Engine)

Simple Finite Heat Release Model (SI Engine) Simple Finite Heat Release Model (SI Engine) Introduction In the following, a finite burn duration is taken into account, in which combustion occurs at θ soc (Start Of Combustion), and continues until

More information

Internal Combustion Engine

Internal Combustion Engine Internal Combustion Engine 1. A 9-cylinder, 4-stroke cycle, radial SI engine operates at 900rpm. Calculate: (1) How often ignition occurs, in degrees of engine rev. (2) How many power strokes per rev.

More information

Internal Combustion Engines

Internal Combustion Engines Internal Combustion Engines The internal combustion engine is an engine in which the burning of a fuel occurs in a confined space called a combustion chamber. This exothermic reaction of a fuel with an

More information

Heat Transfer in Engines. Internal Combustion Engines

Heat Transfer in Engines. Internal Combustion Engines Heat Transfer in Engines Internal Combustion Engines Energy Distribution Removing heat is critical in keeping an engine and lubricant from thermal failure Amount of energy available for use: Brake thermal

More information

The Mechanics of Tractor Implement Performance

The Mechanics of Tractor Implement Performance The Mechanics of Tractor Implement Performance Theory and Worked Examples R.H. Macmillan CHAPTER 2 TRACTOR MECHANICS Printed from: http://www.eprints.unimelb.edu.au CONTENTS 2.1 INTRODUCTION 2.1 2.2 IDEAL

More information

FUNDAMENTALS OF POWER PLANTS. Asko Vuorinen

FUNDAMENTALS OF POWER PLANTS. Asko Vuorinen FUNDAMENTALS OF POWER PLANTS Asko Vuorinen 1 Engine cycles Carnot Cycle Otto Cycle Diesel Cycle Brayton Cycle Rankine Cycle Combined Cycles 2 Carnot Engine 3 Carnot Cycle 4 Carnot Cycle, continued Ideal

More information

Chapter 1 Internal Combustion Engines

Chapter 1 Internal Combustion Engines Chapter 1 Internal Combustion Engines 1.1 Performance Parameters Engine performance parameters can be measured by two means; the indicator equipment or the dynamometer. The indicator system consists of

More information

Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition

Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition Chapter 1 Introduction 1-3 ENGINE CLASSIFICATIONS Internal combustion engines can be classified in a number of different ways: 1. Types of Ignition 1 (a) Spark Ignition (SI). An SI engine starts the combustion

More information

LABORATORY MANUAL I. C. ENGINES & GAS TURBINES (ME-317-E)

LABORATORY MANUAL I. C. ENGINES & GAS TURBINES (ME-317-E) LABORATORY MANUAL I. C. ENGINES & GAS TURBINES (ME-317-E) LIST OF EXPERIMENTS S.No. Name of the Experiment 1. To study the constructional details & working principles of two-stroke petrol/ four-stroke

More information

WEEK 4 Dynamics of Machinery

WEEK 4 Dynamics of Machinery WEEK 4 Dynamics of Machinery References Theory of Machines and Mechanisms, J.J.Uicker, G.R.Pennock ve J.E. Shigley, 2003 Prof.Dr.Hasan ÖZTÜRK 1 DYNAMICS OF RECIPROCATING ENGINES Prof.Dr.Hasan ÖZTÜRK The

More information

Analysis of Parametric Studies on the Impact of Piston Velocity Profile On the Performance of a Single Cylinder Diesel Engine

Analysis of Parametric Studies on the Impact of Piston Velocity Profile On the Performance of a Single Cylinder Diesel Engine IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) e-issn: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 2 Ver. II (Mar - Apr. 2015), PP 81-85 www.iosrjournals.org Analysis of Parametric Studies

More information

2.61 Internal Combustion Engines Design Project Solution. Table 1 below summarizes the main parameters of the base engine. Table 1 Base Engine Summary

2.61 Internal Combustion Engines Design Project Solution. Table 1 below summarizes the main parameters of the base engine. Table 1 Base Engine Summary .6 Internal Combustion Engines Design roject Solution Here is a possible solution for the design problem.. Base Engine Table below summarizes the main parameters of the base engine Table Base Engine Summary

More information

Evaluation Of Parameters Affecting The Performance Of Spark-Ignition Engine BY Bello Lawal And Dr. Isa Garba

Evaluation Of Parameters Affecting The Performance Of Spark-Ignition Engine BY Bello Lawal And Dr. Isa Garba Evaluation Of Parameters Affecting The Performance Of Spark-Ignition Engine BY Bello Lawal And Dr. Isa Garba ABSTRACT This paper focused on the performance of a spark-ignition (engine, which is affected

More information

Al-Balqa Applied University

Al-Balqa Applied University تا سست عام 997 Specialization Common Course Number 202073 Course Title Internal Combustion Engines Credit Hours 3 Theoretical Hours 3 Practical Hours 0 صفحة () من (0) تا سست عام 997 Brief Course Description:

More information

AT 2303 AUTOMOTIVE POLLUTION AND CONTROL Automobile Engineering Question Bank

AT 2303 AUTOMOTIVE POLLUTION AND CONTROL Automobile Engineering Question Bank AT 2303 AUTOMOTIVE POLLUTION AND CONTROL Automobile Engineering Question Bank UNIT I INTRODUCTION 1. What are the design considerations of a vehicle?(jun 2013) 2..Classify the various types of vehicles.

More information

AME 436. Energy and Propulsion. Lecture 6 Unsteady-flow (reciprocating) engines 1: Basic operating principles, design & performance parameters

AME 436. Energy and Propulsion. Lecture 6 Unsteady-flow (reciprocating) engines 1: Basic operating principles, design & performance parameters AME 436 Energy and Propulsion Lecture 6 Unsteady-flow (reciprocating) engines 1: Basic operating principles, design & performance parameters Outline Classification of unsteady-flow engines Basic operating

More information

INTERNAL COMBUSTION ENGINES

INTERNAL COMBUSTION ENGINES Second Edition Fundamentals of INTERNAL COMBUSTION ENGINES Solenoid winding Electrical connection Pintle Valve needle Return spring H.N. Gupta FUNDAMENTALS OF INTERNAL COMBUSTION ENGINES SECOND EDITION

More information

Vol-3 Issue India 2 Assistant Professor, Mechanical Engineering Dept., Hansaba College of Engineering & Technology, Gujarat, India

Vol-3 Issue India 2 Assistant Professor, Mechanical Engineering Dept., Hansaba College of Engineering & Technology, Gujarat, India Review Paper on Effect of Variable Thermal Properties of Working Fluid on Performance of an IC Engine Cycle Desai Rahulkumar Mohanbhai 1, Kiran D. Parmar 2 1 P. G. Student, Mechanical Engineering Dept.,

More information

Fundamentals of steam turbine systems

Fundamentals of steam turbine systems Principles of operation Fundamentals of steam turbine systems - The motive power in a steam turbine is obtained by the rate of change in momentum of a high velocity jet of steam impinging on a curved blade

More information