Quick Coupling Products Distribution. Catalogue 3800-DS/UK

Transcription

1 Quick Coupling Products Distribution Catalogue 38-DS/UK

2 For your safety! Under certain circumstances, quick couplings can be subjected to extreme loadings such as vibration and uncontrolled pressure peaks. Only by using genuine Parker Components and following Parker assembly instructions can you be assured of the reliability and safety of the product and their conformity to the applicable standards. Failure to follow this rule can adversely affect the functional safety and reliability of products, cause personal injury, property damage, and result in loss of your guarantee rights. Subject to alteration. For your safety: see safety guide (pages 58-59) All dimensions used in this catalogue are in mm otherwise the units are specifi ed. The rated pressure is in MPa. If necessary you can also use the conversion table on page 6. The products described herein, including without limitation, products features, dimensions, specifications and designs are subject to change by Parker Hannifi n Corporation and its subsidiaries at any time without notice. For the product availability of Parker components, please refer to price list Copyright 24, revised 1/6, Parker Hannifi n Corporation. All Right Reserved.

3 HYDRAULIC QUICK COUPLINGS How to select a quick coupling...page 2 INDUSTRIAL AND CHEMICAL ISO B quick couplings...6 Series...Page 4 Flush-faced quick couplings female thread BSPP...FEF Series...Page 12 ISO 1628 flush-faced quick couplings...fem Series...Page 15 Cooling flush-faced quick couplings...nsi Series...Page 19 HIGH PRESSURE High pressure quick couplings 15 MPa...CM Series...Page 21 High pressure quick couplings 1 MPa...CL Series...Page 23 High pressure screw type quick couplings 7 MPa...3 Series...Page 25 MOBILE ISO A quick couplings female thread BSPP...66 Series...Page 27 ISO A quick couplings other threads...2 Series...Page 3 Rigid couplings Series...Page 35 General purpose quick couplings...4 Series...Page 38 Screw type quick couplings...qhpa Series...Page 41 Multicouplings 2 lines...mach 2...Page 45 Multicouplings 4 to 7 lines...mach System...Page 48 APPENDICES Fluid compatibility chart... Page 52 Safety guide... Page 58 Conversion factors... Page 6 Alpha numeric index... Page 63 Parker Hannifin Corporation... Page 65 1 Parker Hannifin

4 How to select a hydraulic quick coupling? Features Series Industrial and Chemical High pressure Brass 6 Series Steel Stainless Steel FEF FEM NSI CM CL 3 Series Series Series Series Series Series Picture max. Interchangeable Interchangeable Interchangeable Interchangeable Interchangeable Standards ISO B with with with with with similar ISO 1628 similar similar similar similar models models models models models Material Brass Steel Stainless Steel and Size 1/8" 1/4" 3/8" 1/2" 5/8" 3/4" 1" 1 1/2 " 2 1/2 " Rated pressure* MPa 1/8" /4" /8" /2" /8" /4" " /2 " /2 " Temperature range* -4 C -2 C -2 C -2 C -3 C -3 C -3 C (with NBR seal) +11 C +1 C +1 C +2 C +1 C +1 C +11 C Seal NBR or FKM NBR NBR FKM NBR NBR NBR or Polyurethane Coupler style Manual Screw-to-connect Push-Pull Push-to-connect Valving Poppet Flat-faced poppet Ball Connection possible with pressure on* Female body Male tip Locking mechanism Screw type With cam Ball locking mechanism or End configuration BSPP BSPP BSPP BSPP NPTF Metric Metric BSPP BSPP NPTF Full technical data page *Data shown here are indicative for quick selection purposes only. Please check technical data indicated for each individual series and always refer to safety guide pages Parker Hannifin

5 How to select a hydraulic quick coupling? Series Mobile Features QHPA MACH MACH Series Series Series Series Series 2 System Picture max. Interchangeable Standards ISO A ISO A ISO A ISO A with (1/2") similar ISO A ISO A models Material Brass Steel Stainless Steel Size 1/8" 1/4" 3/8" 1/2" 5/8" 3/4" 1" 1 1/2 " 2 1/2 " Rated pressure* MPa 1/8" 1/4" /8" /2" /8" 3/4" " /2 " 2 1/2 " Temperature range* -4 C -25 C -3 C -4 C -25 C -3 C -3 C (with NBR seal) +11 C +11 C +11 C +11 C +11 C +11 C +11 C Seal NBR NBR NBR NBR NBR NBR NBR Coupler style Manual Screw-to-connect Push-Pull Push-to-connect Valving Poppet Flat-faced poppet Ball Connection possible pressure on* Female body Male tip Locking mechanism Screw type With cam Ball locking mechanism or or End configuration BSPP BSPP, NPTF Metric BSPP BSPP Metric UNF NPTF Metric Metric Metric Full technical data page *Data shown here are indicative for quick selection purposes only. Please check technical data indicated for each individual series and always refer to safety guide pages Parker Hannifin

6 Industrial and chemical 6 Series max ISO B Brass, steel, 1/8", 1/4" 35 MPa -4 C + 11 C NBR (brass, Manual Poppet No Ball locking BSPP, stainless 3/8", 1/2" (NBR seal) steel, AISI 33 mechanism NPTF steel 33 3/4", 1" -2 C + 2 C stainless steel), and /2 ", 2 1/2 " (FKM seal : FKM (Viton TM Viton TM ) AISI 316 stainless steel) Main characteristics Meets the requirements of ISO , Series B Can be used for any type of industrial applications because of the broad range of materials, seals and end configurations Applications Semiconductor industry, steel manufacturing Pneumatic and hydraulic hand tools Food and bottling industry Boating, shipbuilding and offshore industry Pharmaceutical industry, laboratories Transport Power generating plants, hydroelectric power stations (filling / connection of mobile filtration equipment) Technical features Single acting sleeve. Connection and disconnection are possible by pulling the sleeve Poppet style valving: the seal is crimped to prevent seal washout at high fl ow rates Body seal: steel versions feature PTFE back-up ring which prevents seal washout at high flow rates. Brass couplers have a double O-ring seal for redundancy in low pressure and vacuum applications Ball locking mechanism 4 Parker Hannifin

7 Industrial and chemical 6 Series Technical performance data Low cycle, non-pulsating pressure rating: Applications with lower cycle time and no severe cyclic pressure fl uctuations, essentially steady pressure during an operating cycle. Typical applications include hydraulic jacks, mine roof support systems, and high pressure fluid transfer (pumping water or slurry in oil wells). Minor pump ripple is considered non-pulsating. Impulse tested at rated pressure. ANSI/ISO Pressure rating: Dynamic applications with normal to moderate hydraulic shocks such as general industrial equipment, hydraulic presses, agricultural equipment. Impulse tested at a multiple (125 % or 133 %) of rated pressure. A uniform cycle rate of.5 to 1. Hz is held over 1, cycles according to ISO & 2. 15% 5% 5% Test pressure ± 5% test pressure 15% test pressure 1 bar (1 kpa) bar ( kpa) 5% 5% 1% (5±5)% 1 period Low cycle, non-pulsating pressure rating MPa Body size Steel Stainless Brass inch steel 1/8" /4" /8" /2" /4" " /2" /2" ANSI/ISO Pressure rating MPa Body size Steel Stainless Brass inch steel 1/8" /4" /8" /2" /4" " /2" /2" * Values shown for stainless steel are valid for both AISI 33 and AISI 316. Temperature rating : Part number suffi x O-ring compound Temperature range Standard No suffi x NBR (Nitrile) -4 C +11 C Y FKM (Viton ) -2 C +2 C Option W EPDM (Ethylene Propylene) -4 C +15 C Z CR (Neoprene) -4 C +1 C Vacuum data : 696 mm Hg both connected and disconnected 5 Parker Hannifin

8 Industrial and chemical 6 Series Pressure drop Tests with oil viscosity 43 cst at 38 C. 1/8" and 1/4" 3/8" and 1/2" /8" 1/4" /8" 1/2".35 3/4" and 1" /4" 1".3 1 1/2".6 2 1/2" /2" /2" 6 Parker Hannifin

9 Industrial and chemical 6 Series Dimensions and part numbers STEEL COUPLERS Body size Thread A d1 Hex 1 LF d2 Hex 2 L LM Ø Part number Weight Part number Weight inch inch mm inch mm mm inch mm mm mm female body gr./piece male tip gr./piece Female BSPP thread 1/8" 1/ /16" /16" H1-62-BSPP 81 H1-63-BSPP 18 1/4" 1/ /16" /4" H2-62-BSPP 13 H2-63-BSPP 38 3/8" 3/ " /8" H3-62-BSPP 241 H3-63-BSPP 68 1/2" 1/ /8 " /8 " H4-62-BSPP 36 H4-63-BSPP 122 3/4" 3/ /16 " /8 " H6-62-BSPP 62 H6-63-BSPP 217 1" /8 " /8 " H8-62-BSPP 96 H8-63-BSPP 341 Female NPTF thread 1/8" 1/ /16" /16" H H /4" 1/ /16" /4" H H /8" 3/ /8" /8" H H /2" 1/ /8 " /8 " H H /4" 3/ /16 " /8 " H H " / /8 " /8 " H H Body size Thread A d1 Hex 1 LF d2 Hex 2 L LM Ø Part number Part number inch inch mm inch mm mm inch mm mm mm female body male tip Female BSPP thread 1 1/2 " 1 1/ /8 " /8 " H12-62L-BSPP H12-63L-BSPP 1 1/ /8 " /8 " H12-62N-BSPP H12-63N-BSPP 2 1/2 " /4 " /4 " H BSPP H BSPP Female NPTF thread 1 1/2 " 1 1/4-11 1/ /8 " /8 " H12-62L H12-63L 1 1/2-11 1/ /8 " /8 " H12-62N H12-63N 2 1/2 " / /4 " /4 " H H / /4 " /4 " H22-62 H22-63 Note : Quick couplings with UNF thread are also available upon request. Please consult us for these confi gurations. 7 Parker Hannifin

10 Industrial and chemical 6 Series AISI 33 STAINLESS STEEL COUPLERS Body size Thread A d1 Hex 1 LF d2 Hex 2 L LM Ø Part number Weight Part number Weight inch inch mm mm mm mm mm mm female body gr./piece male tip gr./piece Female BSPP thread 1/8" 1/ /16" /16" SH1-62-BSPP 81 SH1-63-BSPP 18 1/4" 1/ mm mm SH2-62-BSPP 129 SH2-63-BSPP 36 3/8" 3/ " /8" SH3-62-BSPP 245 SH3-63-BSPP 69 1/2" 1/ /8 " /8 " SH4-62-BSPP 36 SH4-63-BSPP 122 3/4" 3/ /16 " /8 " SH6-62-BSPP 63 SH6-63-BSPP 217 1" /8 " /8 " SH8-62-BSPP 98 SH8-63-BSPP 345 Female NPTF thread 1/8" 1/ /16" /16" SH SH /4" 1/ /16" /4" SH SH /8" 3/ /8" /8" SH SH /2" 1/ /8 " /8 " SH SH /4" 3/ /16 " /8 " SH SH " / /8 " /8 " SH SH Body size Thread A d1 Hex 1 LF d2 Hex 2 L LM Ø Part number Part number inch inch mm inch mm mm inch mm mm mm female body male tip Female BSPP thread 1 1/2 " 1 1/ /2 " /2 " SH12-62N-BSPP SH12-63N-BSPP Female NPTF thread 1 1/2 " 1 1/2-11 1/ /8 " /8 " SH12-62N SH12-63N Note : Quick couplings with UNF thread are also available upon request. Please contact us for these confi gurations. 8 Parker Hannifin

11 Industrial and chemical 6 Series AISI 316 STAINLESS STEEL COUPLERS Body size Thread A d1 Hex 1 LF d2 Hex 2 L LM Ø Part number Weight Part number Weight inch inch mm mm mm mm mm mm female body gr./piece male tip gr./piece Female BSPP thread 1/8" 1/ mm mm SSH1-62Y-BSPP* 74 SSH1-63Y-BSPP* 22 1/4" 1/ /16" /4" SSH2-62Y-BSPP* 46 SSH2-63Y-BSPP* 42 3/8" 3/ " /8" SSH3-62Y-BSPP* 187 SSH3-63Y-BSPP* 6 1/2" 1/ /8 " /8 " SSH4-62Y-BSPP* 367 SSH4-63Y-BSPP* 123 3/4" 3/ /16 " /8 " SSH6-62Y-BSPP* 61 SSH6-63Y-BSPP* 218 1" mm mm SSH8-62Y-BSPP* 899 SSH8-63Y-BSPP* 34 Filetage femelle NPTF 1/8" 1/ /16" /16" SSH1-62Y* 74 SSH1-63Y* 18 1/4" 1/ /16" /4" SSH2-62Y* 138 SSH2-63Y* 37 3/8" 3/ /8" /8" SSH3-62Y* 18 SSH3-63Y* 55 1/2" 1/ /8 " /8 " SSH4-62Y* 346 SSH4-63Y* 19 3/4" 3/ /16 " /8 " SSH6-62Y* 592 SSH6-63Y* 21 1" / /8 " /8 " SSH8-62Y* 91 SSH8-63Y* 345 *Suffix Y designates FKM (Viton ) seal. Note : Quick couplings with UNF thread are also available upon request. Please contact us for these confi gurations. 9 Parker Hannifin

12 Industrial and chemical 6 Series BRASS COUPLERS Body size Thread A d1 Hex 1 LF d2 Hex 2 L LM Ø Part number Weight Part number Weight inch inch mm inch mm mm inch mm mm mm female body gr./piece male tip gr./piece Female BSPP thread 1/8" 1/ /16" /16" BH1-6-BSPP 87 BH1-61-BSPP 19 1/4" 1/ /16" /4" BH2-6-BSPP 158 BH2-61-BSPP 45 3/8" 3/ " /8" BH3-6-BSPP 26 BH3-61-BSPP 74 1/2" 1/ /8 " /8 " BH4-6-BSPP 383 BH4-61-BSPP 131 3/4" 3/ /16 " /8 " BH6-6-BSPP 642 BH6-61-BSPP 235 1" /8 " /8 " BH8-6-BSPP 971 BH8-61-BSPP 368 Female NPTF thread 1/8" 1/ /16" /16" BH1-6 8 BH /4" 1/ /16" /4" BH BH /8" 3/ /8" /8" BH BH /2" 1/ /8 " /8 " BH BH /4" 3/ /16 " /8 " BH BH " / /8 " /8 " BH BH Body size Thread A d1 Hex 1 LF d2 Hex 2 L LM Ø Part number Part number inch inch mm inch mm mm inch mm mm mm female body male tip Female BSPP thread 1 1/2 " 1 1/ /8 " /8 " BH12-6L-BSPP BH12-61L-BSPP 1 1/ /8 " /8 " BH12-6N-BSPP BH12-61N-BSPP 2 1/2 " /4 " /4 " BH216-6-BSPP BH BSPP Female NPTF thread 1 1/2 " 1 1/4-11 1/ /8 " /8 " BH12-6L BH12-61L 1 1/2-11 1/ /8 " /8 " BH12-6N BH12-61N 2 1/2 " / /4 " /4 " BH216-6 BH Note : Quick couplings with UNF thread are also available upon request. Please contact us for these confi gurations. 1 Parker Hannifin

13 Industrial and chemical 6 Series Options Heavy duty nipples: Parker 6 series heavy duty nipples are recommended for extended life in applications where high cycle rates and pressure surges are encountered. Machined from high tensile steel and specially hardened. To specify a heavy duty nipple, add the prefi x HD to the steel series part number, thus: HDH2-63 and contact us. Sleeve-lock: 6 series couplers (as well as sleeve type couplers) are available with safety locking sleeves. Please add the suffix SL to the part number, e.g. H3-62SL and contact us. Seals: Other seal materials (Ethylene Propylene - EPDM, Neoprene - CR, Perfl uoelastomer - Kalrez ) are available upon request. Please contact us for further information. Dust caps and plugs Body size Plug part number Cap part number inch for female body for male tip Aluminium Rubber Aluminium Rubber 1/8 H1-65 H1-65M H1-66 H1-66M 1/4" H2-65 H2-65M H2-66 H2-66M 3/8" H3-65 H3-65M H3-66 H3-66M 1/2" H4-65 H4-65M H4-66 H4-66M 3/4" H6-65 H6-65M H6-66 H6-66M 1" H8-65 H8-65M H8-66 H8-66M 1 1/2" H H Stainless steel AISI 316 dust plugs and caps are available upon request. Please consult us. Replacement seals Body size Body seal Back-up ring* inch NBR (Nitrile) FKM (Viton TM ) PTFE 1/8" JT213N674 JT213V747 H67A-28 1/4" JT215N674 JT215V747 H67C-28 3/8" JT2116N674 JT2116V /2" JT2213N674 JT2213V /4" JT2218N674 JT2218V " JT2222N674 JT2222V /2" JT2224N674 (2 body seals necessary) - 2 1/2" JT2333N674 - *Brass 6 series couplers use two O-rings but do not use a back-up ring. 11 Parker Hannifin

14 Industrial and chemical FEF Series max Inter- Steel from 1/4" 3 MPa -2 C NBR Push-to- Flush-faced No Ball locking BSPP changeable to 1" + 1 C (nitrile) Connect poppet mechanism with similar with security models Main characteristics Dimensions meet the requirements of ISO 1628 Minimal fluid loss during disconnection Minimal inclusion of air or external contamination during connection Safety system protecting against accidental disconnection Minimal pressure drop Applications Industrial applications Agriculture Road service vehicles, snow ploughs Construction: excavators, rock hammers Technical features Chrome 6 free plated steel Seal : NBR (Nitrile) and backup ring in PTFE to withstand flow surges at high fl ow rates Ball locking mechanism Valving: flush-faced poppet for reduced spillage during disconnection. The seal is crimped to prevent seal washout at high flow rates A safety sleeve lock prevents accidental disconnection. Sleeve is rotated to the stop to engage the lock Push-to-connect system: push on the male tip to connect and pull on the sleeve to disconnect 12 Parker Hannifin

15 Industrial and chemical FEF Series Technical performance data Body size Temperature Max. operating pressure Min. burst pressure inch range connected* connected* MPa MPa 1/4" /8" /2" C + 1 C 5/8" /4" " 25 1 *Warning : the maximum operating pressure and the burst pressure are valid only for the connected position. Do not use the female body disconnected with pressure impulses. Pressure drop Tests with oil viscosity 43 cst at 38 C. 1/4" /8" /2" /8" /4" " Parker Hannifin

16 Industrial and chemical FEF Series Dimensions and part numbers A A d1 Ø d2 HEX 1 LF LM HEX 2 LT Body size Thread A d1 Hex 1 LF d2 Hex 2 LM LT connected Ø Part number Weight Part number Weight pouce pouce mm mm mm mm mm mm mm mm female body gr./pièce male tip gr./pièce Female BSPP thread 1/4" 1/ FEF-251-4FB 147 FEF-252-4FB 86 3/8" 3/ FEF-371-6FB 247 FEF-372-6FB 121 1/ FEF-371-8FB 249 FEF-372-8FB 128 1/2" 1/ FEF-51-8FB 39 FEF-52-8FB 233 3/ FEF-51-12FB 428 FEF-52-12FB 227 5/8" 3/ FEF FB 499 FEF FB 268 3/4" FEF FB 811 FEF FB 394 1" 1-1/ FEF-11-2FB 1266 FEF-12-2FB 641 Dust caps and plugs Plastic Body size Plug part number Cap part number inch for female body for male tip 1/4" PFE-251-P CFE-252-P 3/8" PFE-371-P CFE-372-P 1/2" PFE-51-P CFE-52-P 5/8" PFE-621-P CFE-622-P 3/4" PFE-751-P CFE-752-P 1" PFE-11-P CFE-12-P Automatic dust cap for female body Plastic Body size Cap part number inch for female body 1/2" DFE-51-P Note : Standard dust caps and plugs are black. Please consult us for other colours. 14 Parker Hannifin

17 Industrial and chemical FEM Series max ISO 1628 Steel from 1/4" 31.5 MPa -2 C NBR Push-to- Flush-faced No Ball locking BSPP, and HTMA to 1" + 1 C (nitrile) Connect poppet mechanism Metric (for size 3/8") with security Main characteristics Meets the requirements of ISO 1628 Minimal fluid loss during disconnection Minimal inclusion of air or external agents during connection Safety system protecting against accidental disconnection Modular construction: broad choice of end confi gurations Minimal pressure drop Applications Hydraulic applications: excavators, rock hammers, drilling rigs Road service vehicles, snow ploughs Diffi cult working conditions: pressure impulses Technical features Chrome 6 free plated steel Seal : NBR (Nitrile) and backup ring in PTFE to withstand fl ow surges at high fl ow rates Ball locking mechanism Valving: flush-faced poppet for reduced spillage during disconnection. The seal is crimped to prevent seal washout at high fl ow rates A safety sleeve lock prevents accidental disconnection. Sleeve is rotated to the stop to engage the lock Push-to-connect system: push on the male tip to connect and pull on the sleeve to disconnect 15 Parker Hannifin

18 Industrial and chemical FEM Series Technical performance data Body size Temperature Max. operating pressure Min. burst pressure inch range MPa MPa 1/4" /8" /2" C + 1 C 5/8" /4" " 2. 8 Pressure drop Tests with oil viscosity 43 cst at 38 C..45 1/4".45 3/8" /2".45 5/8" /4".45 1" Parker Hannifin

19 Industrial and chemical FEM Series Dimensions and part numbers Female BSPP thread DIN 3852 Body size Thread A d1 Hex 1 LF d2 Hex 2 LM LT connected Ø Part number Weight Part number Weight inch inch mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece Female BSPP thread 1/4" 1/ FEM-251-4FB 193 FEM-252-4FB 86 3/8" 3/ FEM-371-6FB 286 FEM-372-6FB 146 1/ FEM-371-8FB 286 FEM-372-8FB 146 1/2" 1/ FEM-51-8FB 467 FEM-52-8FB 235 3/ FEM-51-12FB 477 FEM-52-12FB 273 5/8" 3/ FEM FB 64 FEM FB 299 3/4" FEM FB 983 FEM FB 475 1" 1-1/ FEM-11-2FB 1365 FEM-12-2FB cone DIN 2353 Body size Series Tube DN Thread A d1 Hex LF d2 LM LT connected L4 Ø Part number Weight Part number Weight inch O/D D2 mm mm mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece Male metric thread L* 1 8 M16X FEM MCL 27 FEM MCL 155 3/8" L* 12 1 M18X FEM MCL 262 FEM MCL 155 L* M22X FEM MCL 268 FEM MCL 161 1/2" *Light series L* 12 1 M18X FEM-51-18MCL 433 FEM-52-18MCL 259 L* M22X FEM-51-22MCL 441 FEM-52-22MCL Parker Hannifin

20 Industrial and chemical FEM Series 24 cone DIN Bulkhead Body size Series Tube DN Thread A d1 Hex LF d2 LM LT connected L4 Ø Part number Weight Part number Weight inch O/D D2 mm mm mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece Male metric thread L* 1 8 M16X FEM BMCL 284 FEM BMCL 169 3/8" L* 12 1 M18X FEM BMCL 279 FEM BMCL 171 L* M22X FEM BMCL 296 FEM BMCL 188 1/2" *Light series L* 12 1 M18X FEM-51-18BMCL 451 FEM-52-18BMCL 275 L* M22X FEM-51-22BMCL 467 FEM-52-22BMCL 292 Dust caps and plugs Plastic Body size Plug part number Cap part number inch for female body for male tip 1/4" PFE-251-P CFE-252-P 3/8" PFE-371-P CFE-372-P 1/2" PFE-51-P CFE-52-P 5/8" PFE-621-P CFE-622-P 3/4" PFE-751-P CFE-752-P 1" PFE-11-P CFE-12-P Automatic dust cap for female body Plastic Body size Cap part number inch for female body 1/2" DFE-51-P Note : Standard dust caps and plugs are black. Please consult us for other colours 18 Parker Hannifin

21 Industrial and chemical NSI Series Inter- Brass 1/4" 6. MPa -2 C FKM Manual Flat- No Ball locking BSPP, changeable and +2 C (Viton TM ) faced mechanism Metric with Stainless poppet similar steel models Main characteristics Minimal fluid loss during disconnection Minimal inclusion of air or dust during connection Maximal flow Compact design Applications Thermoplastic injection moulding: for cooling of machinery or temperatures control lines Can be used with cold and hot water as well as with heat transfer oils Technical features Valving: flush-faced poppet for reduced spillage during disconnection Seal : Eolastic (ED) for long-term reliability without retightening Single active sleeve: connection and disconnection are possible by pulling the sleeve Ball locking mechanism Seal: FKM (Viton TM ) 19 Parker Hannifin

22 Industrial and chemical NSI Series Technical performance data Body size Temperature Max operating pressure Min burst pressure inch range MPa MPa 1/4" -2 C +2 C Pressure drop Test with oil viscosity 43 cst at 38 C.16 1/4" Dimensions and part numbers Elbowed female version - 24 Cone - DIN /4" Body size Thread A d1 Hex LF L Thread B L4 LM LT connected Ø Part number Weight Part number Weight inch metric mm mm mm mm BSPP mm mm mm mm female body gr./piece male tip gr./piece 1/4 M16x / NSI-251-C16MCL 18 NSI-252-4MBE 48 Straight female version - 24 Cone - DIN 2353 Body size Thread A d1 Hex LF L Thread B L4 LM LT connected Ø Part number Weight Part number Weight inch metric mm mm mm mm BSPP mm mm mm mm female body gr./piece male tip gr./piece 1/4 M16x / NSI MCL 84 NSI-252-4MBE 48 Other quick couplings for temperature regulation on thermoplastic or aluminium injection moulds will be available soon. Please contact your Parker Sales Engineer. 2 Parker Hannifin

23 High pressure CM Series max Inter- Steel 1/4" 15 MPa -3 C NBR Manual Flat-faced No Ball locking BSPP changeable + 1 C (nitrile) poppet mechanism with similar with security models Main characteristics High pressure coupler up to 15 MPa Interchangeable with similar products Reduced spillage Maximal security due to a positive locking mechanism Applications Very high pressure hydraulic equipment, clamping devices, torque wrenches, nut runners Cable cutters Knockout punches Technical features A safety sleeve lock prevents accidental disconnection. Sleeve is rotated to the stop to engage the lock Valving: flush-faced poppet for reduced spillage during disconnection Chrome 6 free plated steel Single active sleeve: connection and disconnection are possible by pulling the sleeve Ball locking mechanism 21 Parker Hannifin

24 High pressure CM Series Technical performance data Body size Temperature Max. operating pressure Min. burst pressure Spillage max inch range MPa MPa per disconnection* (ml) 1/4" -3 C +1 C 15 >35.25 *Test according to ISO Pressure drop Test with oil viscosity 32 cst at 4 C /4" Dimensions and part numbers Body size Thread A d1 d3 Hex1 LF d2 Hex2 LM LT Ø Part number Weight Part number Weight inch BSPP mm mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece 1/4" 1/4" CM-251-4FB-PLP* 192 CM-252-4FB-PLC** 69 * with plug ** with cap Dust caps and plugs Body size Plug part number Cap part number inch for female body for male tip 1/4" CPP-253 CPC-254 Standard dust caps and plugs are yellow. 22 Parker Hannifin

25 High pressure CL Series max Inter- Steel 1/4" 1 MPa -3 C NBR Manual Flat-faced No Ball locking BSPP changeable + 1 C (nitrile) poppet mechanism with similar with security models Main characteristics High pressure coupling up to 1 MPa Interchangeable with similar products Reduced spillage Maximal security due to a positive locking mechanism Applications Rescue equipment: lifting bags, spreaders, cutters Very high pressure hydraulic equipment: hydraulic jacks, rams, clamping devices, torque wrenches, cable cutters Technical features A safety sleeve lock prevents accidental disconnection. Sleeve is rotated to the stop to engage the lock Valving: flush-faced poppet for reduced spillage during disconnection Single active sleeve: connection and disconnection are possible by pulling the sleeve Ball locking mechanism Chrome 6 free plated steel 23 Parker Hannifin

26 High pressure CL Series Technical performance data Body size Temperature Max operating pressure Min burst pressure Spillage max inch range MPa MPa per disconnection* (ml) 1/4" -3 C +1 C 1 >3.25 *Test according to ISO Pressure drop Test with oil viscosity 32 cst at 4 C.14 1/4" Dimensions and part numbers Body size Thread A d1 d3 Hex1 LF d2 Hex2 LM LT Ø Part number Weight Part number Weight inch BSPP mm mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece 1/4" 1/4" CL-251-4FB-PLP* 192 CL-252-4FB-PLC** 69 * with plug ** with cap Dust caps and plugs Body size Plug part number Cap part number inch for female body for male tip 1/4" CPP-253 CPC-254 Standard dust caps and plugs are yellow. 24 Parker Hannifin

27 High pressure 3 Series max Inter- Steel 1/4" & 3/8" 7 MPa -3 C + 11 C NBR (1/4") Screw-to- Ball or No Screw NPTF changeable (NBR seal) Polyurethane connect poppet mechanism with similar -3 C + 8 C (3/8") models (polyurethane seal) Main characteristics High pressure coupler up to 7 MPa Interchangeable with similar products Screw locking mechanism Ball or poppet valving Applications Portable hydraulic rams Hydraulic jacks, rams and clamping devices Clamping hand tools Rescue equipment Technical features Seal : - size 1/4" : NBR (Nitrile) - size 3/8" : Polyurethane Chrome 6 free plated steel. Female body and nipple are in high strength steel to prolong life Screw type locking mechanism Ball or poppet valving. (as per chart on page 26) It is possible to connect a male tip with a ball valving and a female body with a poppet valving, and vice-versa. Be careful! Couplers should be pressurized only when completely connected and should not be coupled or uncoupled when pressurized. 25 Parker Hannifin

28 High pressure 3 Series Technical performance data Body size Temperature range Max. operating pressure (static) inch MPa 1/4" -3 C +11 C 7 3/8" -3 C +8 C 7 Pressure drop Test with oil viscosity 43 cst at 38 C. Ball valving Poppet valving 1.2 1/4" and 3/8".6 1/4" and 3/8" Dimensions and part numbers B HEX 2 d1 Ø d2 A HEX 1 LF LM LT Body size Thread A Thread B d1 Hex 1 LF d2 Hex 2 LM LT connected Ø Valving Part number Weight Part number Weight inch female male mm mm mm mm mm mm mm Ball Poppet female body gr./piece male tip gr./piece NPTF thread 1/4 1/ /16" /4" 1/4 1/ P P 85 3/8" 3/8 3/ " /16" /8 3/ " P P 11 Dust caps and plugs Replacement seals Body size Dust plug part number Dust cap part number inch for female body for male tip 1/4" /8" Body size Material O-ring seal part number inch 1/4" NBR (Nitrile) JT2114N552 3/8" Polyurethane JT1U QE 26 Parker Hannifin

29 Mobile 66 Series max ISO A Steel 1/4", 3/8", 35 MPa -4 C NBR Manual Poppet No Ball locking BSPP 1/2", 3/4" + 11 C (nitrile) mechanism & 1" Main characteristics Meets the requirements of ISO Series A Reference couplings for general purpose hydraulic applications Applications Used for a wide range of agricultural applications: tractors, accessories Mobile and construction equipment In-plant machinery: hydraulic power units, hand tools Technical features Single acting sleeve. Connection and disconnection are possible by pulling the sleeve Seal: NBR (nitrile) and backup ring in PTFE to withstand fl ow surges at high fl ow rate Ball locking mechanism Chrome 6 free plated steel Poppet style valving: the seal is crimped to prevent seal washout at high fl ow rates 27 Parker Hannifin

30 Mobile 66 Series Technical performance data Body size Temperature range Max. operating pressure inch MPa 1/4" 35 3/8" 28 1/2" -4 C +11 C 28 3/4" 28 1" 28 Pressure drop Tests with oil viscosity 43 cst at 38 C. 1/4" 3/8" /4" 3/8" 1/2" /2" 3/4" 1" /4" 1" 28 Parker Hannifin

31 Mobile 66 Series Dimensions and part numbers Body size Thread A d1 Hex 1 LF d2 Hex 2 LM LT Ø Part number Weight Part number Weight inch BSPP mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece 1/4" 1/ /8" 3/ /2" 1/ /4" 3/ " Dust caps and plugs Body size Dust plug part number Dust cap part number inch for female body for male tip 1/4" PL PL 3/8" PL PL 1/2" PL PL 3/4" PL PL 1" PL PL Note : Standard dust caps and plugs are red. Please consult us for other colours. Replacement seals Body size O-ring Back-up ring inch NBR (Nitrile) NBR (Nitrile) 1/4" JT2112N /8" JT2115N /2" JT2211N /4" JT2123N " JT2126N Parker Hannifin

32 Mobile 2 Series max ISO Steel 3/8" and 1/2" 31.5 MPa -25 C NBR Push-Pull Ball No Ball locking BSPP A + 11 C (nitrile) or poppet mechanism NPTF Metric Main characteristics Meets the requirements of ISO Series A Modular construction : broad choice of end configurations (BSPP, NPTF and metric) Applications Used for a wide variety of agricultural applications: tractors, accessories Mobile and construction equipment Industrial equipment Technical features Double acting sleeve (Push-Pull) Ball or three-part poppet style valving with a moulded shaped seal to prevent seal washout at high fl ow rates. Chrome 6 free plated steel Seal: NBR (Nitrile) and back-up ring in PTFE to withstand flow surges at high fl ow rates Ball locking mechanism 3 Parker Hannifin

33 Mobile 2 Series Technical performance data Body size Temperature Max. operating inch range pressure (MPa) Poppet valving 3/8" C +11 C 1/2" 25. Ball valving 1/2" -25 C +11 C 21. Pressure drop Test with oil viscosity 28 cst at 4 C Poppet Valving 3/8" 1/2" Ball Valving.6 1/2" Parker Hannifin

34 Mobile 2 Series Dimensions and part numbers 24 Cone - DIN 2353 Body size Series Tube O/D Thread A d1 Hex LF L LM LT connected L4 ø Part number Weight Part number Weight inch d2 mm mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece Male metric thread 3/8" L* 8 M14x V53D6X2-B 194 4V13D6X2-B 75 L* 1 M16x V53D6X3-B 196 4V13D6X3-B 77 S** 1 M18x V53D7X3-B 21 4V13D7X3-B 82 1/2" L* 8 M14x V54D6X2-B 293 4V14D6X2-B 136 L* 1 M16x V54D6X3-B 295 4V14D6X3-B 137 L* 12 M18x V54D6X4-B 295 4V14D6X4-B 138 L* 15 M22x V54D6X5-B 3 4V14D6X5-B 143 L* 18 M26x V54D6X6-B 36 4V14D6X6-B 148 S** 1 M18x V54D7X3-B 32 4V14D7X3-B 145 S** 16 M24x V54D7X6-B 39 4V14D7X6-B 151 * Light series ** Heavy series 24 Cone - DIN Bulkhead Body size Series Tube O/D Thread A d1 Hex LF L LM LT connected L4 ø Part number Weight Part number Weight inch d2 mm mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece Male metric thread 3/8" L* 1 M16x V53E6X3-B 28 4V13E6X3-B 98 1/2" L* 8 M14x V54E6X2-B 314 4V14E6X2-B 156 L* 1 M16x V54E6X3-B 319 4V14E6X3-B 162 L* 12 M18x V54E6X4-B 325 4V14E6X4-B 166 L* 15 M22x V54E6X5-B 347 4V14E6X5-B 19 L* 18 M26x V54E6X6-B 38 4V14E6X6-B 222 S** 1 M18x V54E7X3-B 334 4V14E7X3-B 176 S** 12 M2x V54E7X4-B 344 4V14E7X4-B 186 S** 16 M24x V54E7X6-B 366 4V14E7X6-B 28 * Light series ** Heavy series 32 Parker Hannifin

35 Mobile 2 Series Dimensions and part numbers Male BSPP thread - DIN Form B Body size Thread A d1 Hex LF L LM LT connected L4 ø Part number Weight Part number Weight inch inch mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece Male BSPP thread 3/8" 3/ V53F4B3-B 195 4V13F4B3-B 75 1/2" 3/ V54F4B3-B 327 4V14F4B3-B 146 1/ V54F4B4-B 311 4V14F4B4-B 154 Female thread - DIN Form Y Body size Thread A d1 Hex LF L LM LT connected L4 ø Part number Weight Part number Weight inch inch mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece Female BSPP thread 3/8" 3/ V53G4X3-B 23 4V13G4X3-B 84 1/2" 3/ V54G4X3-B 327 4V14G4X3-B 168 1/ V54G4X4-B 324 4V14G4X4-B 164 1/ O54G4X4-B* 34 4O14G4X4-B* 11 3/ V54G4X6-B 374 4V14G4X6-B 217 Female metric thread 1/2" M18x V54G8X5-B 322 4V14G8X5-B 165 M22x V54G8X6-B 315 4V14G8X6-B 157 Female NPTF thread 1/2" 1/2NPT O54GZ4-B* 38 4O14GZ4-B* 14 * Ball valving 33 Parker Hannifin

36 Mobile 2 Series Dust caps and plugs Plastic Rubber Steel Body size Dust plug part number Dust cap part number inch for female body for male tip Plastic 3/8" 525-3PR 529-3PR 1/2" 525-4P* 529-4P* Rubber 1/2" 525-4M 529-4M Steel 1/2" * Colour code B = blue G = green R = red O = orange Y = yellow BL = black Automatic dust cap for female body Plastic Body size Cap part number inch for female body 1/2" DFE-51-P Note : Standard dust cap is black. Please consult us for other colours. Replacement seals The KIT contains the O-ring in NBR (nitrile) and the back-up ring in PTFE. Body size Part number inch 3/8" 4V53-KIT 1/2" 4V54-KIT1 1/2" 4V54-KIT2* *KIT 2 is for part numbers 4V54G4X4 and 4O54G4X4. For the other part numbers, use KIT Parker Hannifin

37 Mobile 944 Series max ISO A Steel 1/2" 25 MPa -3 C NBR "Push-Pull" Poppet Yes Ball locking Metric, and + 11 C (nitrile) in the male mechanism UNF ISO 5675 tip up to 25 MPa Main characteristics Rigid coupler which meets the requirements of ISO Series A and ISO 5675 This coupler is a reference for the most important manufacturers of agricultural equipment Must be used with a male tip which meets the requirements of ISO A Optional: connect under max. operating pressure on the female side (please contact us) Applications Medium and high power tractors: direct mounting on the directional valve or rigid piping Technical features Zinc plated steel with a yellow chromate finish Integrated detent system to prevent circuit shut off in back-fl ow condition (15 l./min. with 19 l./min. max from the male tip to the female body) Seal: NBR (Nitrile) and back-up ring of fi lled PTFE to withstand fl ow surges at high fl ow rates Rigid coupling with a double acting sleeve ( Push-Pull ). One hand connection and disconnection: push or pull on male tip to connect or disconnect. Automatic disconnection in case of strong accidental traction on the hose. Ball locking mechanism Valving: three-part poppet with moulded shaped seal 35 Parker Hannifin

38 Mobile 944 Series Technical performance data Body size Temperature range Max. operating pressure Min. burst pressure* inch MPa MPa 1/2" -3 C + 11 C *According to ISO 5675 Pressure drop Tests with oil viscosity 43 cst at 38 C. 1/2" Dimensions and part numbers Male thread to ISO d1 HEX A d2 Body size Thread A d1 Hex LF d2 Part number Weight inch mm mm mm mm mm gr./piece Male metric thread 1/2" M22x F8H6S2 586 LF 24 cone bulkhead - DIN L - ISO 8434 d1 d2 HEX 3 A Body size Tube Thread A d1 Hex LF d2 Part number Weight inch size mm mm mm mm mm gr./piece Male metric thread 1/2" 15L M22x E6Z5S2 71 LF HEX 24 cone bulkhead - SAE J514 - ISO d1 HEX A d2 Body size Thread A d1 Hex LF d2 Part number Weight inch mm mm mm mm mm gr./piece Male UNF thread 1/2" 3/ T5X4S2 615 LF 36 Parker Hannifin

39 Mobile 94 Series Dust caps Single dust cap Body size LT d1 Dust cap inch mm mm part number 1/2" DCP-5* Double dust cap Body size LT d1 A1 Dust cap inch mm mm mm part number DCP-555* 1/2" DCP-572* DCP-582* * Warning: Coloured plugs are not included in the single and double dust caps but have to be ordered separately. Coloured plugs Colour Red Yellow Black Green Blue Part number R J N V B Note : these dust caps are also suitable for the 1/2 2 series. Replacement seals Body size O-ring part number Back-up ring part number inch NBR (Nitrile) fi lled PTFE 1/2" JT2117N F2C 37 Parker Hannifin

40 Mobile 4 Series max ISO A Steel 1/4", 3/8" 2 MPa -4 C NBR Manual Ball No Ball locking BSPP, (1/2" only) 1/2", 3/4" + 11 C (nitrile) or poppet mechanism NPTF 1" Main characteristics The 1/2" body size meets the requirements of ISO Series A Famous coupling widely held on the market Applications Used for a wide range of forestry and agricultural equipment: tractors, agricultural machinery Construction and mobile equipment In-plant machinery Technical features Chrome 6 free plated steel Seal : NBR (Nitrile) Ball locking mechanism Single acting sleeve. Connection and disconnection are possible by handling the sleeve Valving : ball or poppet (as per chart on page 4). The seal is crimped to prevent seal washout at high fl ow rates 38 Parker Hannifin

41 Mobile 4 Series Technical performance data Body size Temperature Max. operating inch range pressure (MPa) 1/4" 2 3/8" 2 1/2" -4 C +11 C 2 3/4" 2 1" 2 Pressure drop Tests with oil viscosity 43 cst at 38 C..3 1/4" & 3/8" /4" 3/8" 1.6 3/4" 1" /2" 3/4 " 1" 39 Parker Hannifin

42 Mobile 4 Series Dimensions and part numbers Body size Thread A d1 Hex 1 LF Hex 2 LM LT connected Ø Valving Part number Weight Part number Weight inch inch mm mm mm mm mm Ball Poppet female body gr./piece male tip gr./piece Female NPTF thread 1/4" 1/ /8" /4" P P 35 3/8" 3/ /16" /16" P P 75 1/2" 3/ /8" /4" /4" 3/ /8" /16" " / /8" /8" P P 28 Female BSPP thread 1/4" 1/ mm mm B B 35 3/8" 3/ mm mm B B 75 Dust caps and plugs Rubber Plastic Steel Body size Dust plug part number Dust cap part number inch for female body for male tip Rubber 1/4" 525-2M 529-2M 3/8" 525-3M 529-3M 1/2" 525-4M 529-4M 3/4" 525-5M 529-5M 1" 525-6M 529-6M Plastic 1/2" 515-4P* 519-4P* Steel 1/2" * Colour code - By ordering, add after the part number the letter corresponding to the colour you wish: B = blue G = green R = red O = orange Y = yellow Example: yellow dust cap = 519-4PY 4 Parker Hannifin

43 Mobile QHPA Series max Inter- Steel 3/8", 1/2", 45 MPa -25 C NBR Screw-to Poppet Yes Screw type BSPP, changeable 3/4" & 1" + 11 C (nitrile) connect up to 5 MPa metric with similar models Main characteristics High pressure coupler up to 45 MPa Interchangeable with similar products Connection with pressure up to 5 MPa is possible Applications Agricultural and mobile equipment Rock hammers Forestry equipment Snow groomers Excavators Technical features Black nitrile seal: - Visual check for correct connection - Prevents accidental disconnection - Prevents external contamination entering the system Three-part poppet style valving with a moulded shaped seal to prevent seal washout at high fl ow rates The sleeve is mounted on the male tip to protect the sealing area Chrome 6 free plated steel Locking: screw type. Self locking thread prevents sleeve from being loosened by vibration Seal: NBR (Nitrile) with a PTFE back-up ring to withstand fl ow surges 41 Parker Hannifin

44 Mobile QHPA Series Technical performance data Body size Temperature Max. operating inch range pressure (MPa) 2 3/8" /2" -25 C /4" +11 C " 2. Be careful! The maximum operating pressures for couplings with metric adaptors light series (DIN 2353) are 31.5 MPa up to 18L and 16. MPa for 22 L Pressure drop Test with oil viscosity 28 cst at 4 C.45 3/8".6 1/2" Flow Flow in (l/min) 3/4" Flow Flow in (l/min) (l/min) 1" Flow in (l/min) Flow in (l/min) 42 Parker Hannifin

45 Mobile QHPA Series Dimensions and part numbers 24 cone - DIN 2353 Body size Series Tube O/D Thread A d1 Hex 1 Hex 2 LF LM LT connected L4 Part number Weight Part number Weight inch d2 mm mm mm mm mm mm mm mm female body gr./piece male tip gr./piece Male metric thread 2 3/8" L* 8 M14x QHPA53-D6X2-B 147 QHPA13-D6X2-B 153 L* 1 M16x QHPA53-D6X3-B 148 QHPA13-D6X3-B 154 S** 1 M18x QHPA53-D7X3-B 154 QHPA13-D7X3-B 16 S** 12 M2x QHPA53-D7X4-B 156 QHPA13-D7X4-B /2" L* 12 M18x QHPA54-D6X4-B 285 QHPA14-D6X4-B 242 L* 15 M22x QHPA54-D6X5-B 29 QHPA14-D6X5-B 247 S** 14 M22x QHPA54-D7X5-B 277 QHPA14-D7X5-B 254 S** 16 M24x QHPA54-D7X6-B 298 QHPA14-D7X6-B /4" L* 18 M26x QHPA56-D6X6-B 729 QHPA16-D6X6-B 656 L* 22 M3x QHPA56-D6X7-B 736 QHPA16-D6X7-B 663 S** 2 M3x QHPA56-D7X7-B 747 QHPA16-D7X7-B 674 S** 25 M36x QHPA56-D7X8-B 765 QHPA16-D7X8-B " S** 3 M42x QHPA58-D7X9-B 1572 QHPA18-D7X9-B 282 * Light series ** Heavy series 24 cone - DIN Bulkhead Body size Series Tube O/D Thread A d1 Hex 1 Hex 2 LF LM LT connected L4 Part number Weight Part number Weight inch d2 mm mm mm mm mm mm mm mm male tip gr./piece female body gr./piece Male metric thread 2 3/8" L* 8 M14x QHPA53-E6X2-B 167 QHPA13-E6X2-B 173 L* 1 M16x QHPA53-E6X3-B 179 QHPA13-E6X3-B 173 S** 1 M18x QHPA53-E7X3-B 188 QHPA13-E7X3-B 194 S** 12 M2x QHPA53-E7X4-B 198 QHPA13-E7X4-B /2" L* 12 M18x QHPA54-E6X4-B 313 QHPA14-E6X4-B 27 L* 15 M22x QHPA54-E6X5-B 337 QHPA14-E6X5-B 294 S** 16 M24x QHPA54-E7X6-B 356 QHPA14-E7X6-B /4" L* 18 M26x QHPA56-E6X6-B 822 QHPA16-E6X6-B 749 S** 2 M3x QHPA56-E7X7-B 865 QHPA16-E7X7-B 792 S** 25 M36x QHPA56-E7X8-B 918 QHPA16-E7X8-B " S** 3 M42x QHPA58-E7X9-B 1757 QHPA18-E7X9-B 235 * Light series ** Heavy series 43 Parker Hannifin

46 Mobile QHPA Series Dimensions and part numbers Male BSPP thread - DIN Form B Body size Thread A d1 Hex 1 Hex 2 LF LM LT connected L4 Part number Weight Part number Weight inch inch mm mm mm mm mm mm mm male tip gr./piece female body gr./piece Male BSPP thread 2 3/8" 3/ QHPA53-F4A3-B 183 QHPA13-F4A3-B /2" 1/ QHPA54-F4A4-B 31 QHPA14-F4A4-B 258 Female BSPP thread - DIN Form Y Body size Thread A d1 Hex 1 Hex 2 LF LM LT connected L4 Part number Weight Part number Weight inch inch mm mm mm mm mm mm mm male tip gr./piece female body gr./piece Female BSPP thread 2 3/8" 3/ QHPA53-G4X3-B 155 QHPA13-G4X3-B /2" 1/ QHPA54-G4X4-B 311 QHPA14-G4X4-B /4" 3/ QHPA56-G4X6-B 838 QHPA16-G4X6-B /4" QHPA56-G4X8-B 786 QHPA16-G4X8-B 713 Dust caps and plugs Replacement seals Polyethylene Body size Dust plug part number Cap part number inch for male tip for female body 3/8" QHPA53-DP QHPA13-DC 1/2" QHPA54-DP QHPA14-DC 3/4" QHPA56-DP QHPA16-DC 1" QHPA58-DP QHPA18-DC Standard dust caps and plugs are red. Body size Part number inch 3/8" QHPA53-KIT* 1/2" QHPA54-KIT* 3/4" QHPA56-KIT* 1" QHPA58-KIT* * The KIT contains the O-ring and the outside ring in NBR (nitrile) as well as the back-up ring in PTFE. 44 Parker Hannifin

47 Mobile MACH 2 max ISO A Steel 1/2" 25 MPa -3 C NBR Manual Poppet Yes Cam Metric + 11 C (nitrile) mechanism Main characteristics Meets the requirements of ISO Series A Possibility of connecting 2 hydraulic lines simultaneously No coupling misconnection or accidental disconnection Possibility of connecting under pressure up to 25 MPa in one hydraulic line only Applications Agricultural applications: front loaders, hedge cutters Road service vehicles: road service lorries, road sweepers, snowploughs Industrial applications: easy and fast connection and disconnection of implements or tooling Technical features Seal : NBR (Nitrile) Steel Central came locking system Poppet style valving with a moulded shaped seal. The seal is crimped to prevent seal washout at high flow rates 45 Parker Hannifin

48 Mobile MACH 2 Technical performance data Body size Temperature range Max. operating pressure Min. burst pressure inch MPa MPa 1/2" -3 C +11 C Pressure drop Tests with oil viscosity 43 cst at 38 C..7 1/2" Functioning Mechanical attachment: 2 mounting holes Ø 8.5 mm Functioning: Locating Locking It is connected Using one hand, the plug is pushed to open the dust cover and then is introduced into the connecting box. Just move the handle with the other hand. The MACH 2 is connected and locked. 46 Parker Hannifin

49 Mobile MACH 2 Dimensions and part numbers Plug : Description : Complete unit including the connecting plug and 2 male tips, which meet the requirements of ISO A. Number of End confi guration Part number Weight hydraulic lines gr./piece 2 DIN L (M22x1.5) MACH2-IA-P 123 Connecting box: Description : Complete unit including the base connector unit, its dust cover, a lever acting as a central locking device and 2 female bodies, which meet the requirements of ISO A. Number of End confi guration Part number Weight hydraulic lines gr./piece 2 DIN L (M22x1.5) MACH2-IA-B 2723 Note : Other types of MACH 2 with non-spill connections are also available upon request. Please consult us for further information. Spare parts Part Female body seal Female body Male tip Part number JT2117N552 LV54D6X5MLXC LV14E6X5MLX 47 Parker Hannifin

50 Mobile MACH System max ISO A Steel 1/2" 25 MPa -3 C NBR Manual Poppet Yes Ball and cam Metric + 11 C (nitrile) locking mechanism Main characteristics Meets the requirements of ISO Series A Possible to connect 4, 5, 6 or 7 hydraulic lines simultaneously No coupling misconnection or accidental disconnection Using a standard interface will still allow end users to connect their standard quick coupling equipped implements In the version with seven lines (MACH 7), the base connector is equipped with an electrical connector as standard feature, which is an option on the MACH 4, 5 and 6. Possible to connect with two lines under 2 MPa, if other lines are not under pressure Applications Agricultural applications: front loaders, hedge cutters Road service vehicles: road systems lorries, road sweepers, snowploughs Industrial applications: easy and fast connection and disconnection of implements or tooling Technical features Steel Body seal : NBR (Nitrile) Individual ball locking system AND : Central cam locking mechanism: a simple movement enables to connect all the hydraulic lines. Three part poppet style valving with a moulded shaped seal to prevent seal washout at high fl ow rates. 48 Parker Hannifin

51 Mobile MACH System Technical performance data Body size Temperature Max. operating Min. burst pressure (MPa) Connection force Disconnection force inch range pressure (MPa) Connected female body male tip without pressure without pressure under 5 MPa 1/2" -3 C +11 C dan 5.5 dan 37. dan Pressure drop Tests with oil viscosity 43 cst at 38 C..7 1/2" Functioning Base unit: Mounted with 4 screws M8x1.25 mm. Functioning: The dust cover is lifted and the top connector put on the base connector. The centring is automatically realised. When it is disconnected, the automatic dust cover assures a complete dust and moisture protection of the base connector. Push down in only one action. It is locked with little effort. 49 Parker Hannifin

52 Mobile MACH System Dimensions and part numbers Top connectors: Description : This top connector unit includes the top casting with 4 to 7 female quick couplings and the complete cam locking system. In the most common version with 7 lines, the top connector is also equipped with a 6-line female electrical connector as a standard feature. Number of Number of threads DIN 2353 Part number Part number hydraulic lines 15L (M22x1.5) 12L (M18x1.5) without electrical connector with electrical connector 4 4 MACH4/715LT MACH4/715LTE 5 5 MACH5/715LT MACH5/715LTE 6 6 MACH6/715LT MACH6/715LTE MACH7T Base connector: Description : This base connector unit includes the base casting and automatic protective cover, 4 to 7 male quick couplings and the positioning pins. Also included are an adaptor and a plastic hose to drain oil. In the most common version with 7 lines, the base connector is also equipped with a 6 line male electrical connector as a standard feature. Number of Number of threads DIN 2353 Part number Part number hydraulic lines 15L (M22x1.5) 12L (M18x1.5) without electrical connector with electrical connector 4 4 MACH4/715LB MACH4/715LBE 5 5 MACH5/715LB MACH5/715LBE 6 6 MACH6/715LB MACH6/715LBE MACH7B 5 Parker Hannifin

53 Mobile MACH System Accessories Oil drain kit: Description : This kit includes the removable tank to contain oil spillage and a holding fi xture. Part number MACH A Spare parts Part Part number Electrical socket MACH Washer MACH Grommet MACH Electrical plug MACH Snap ring MACH Counter plate MACH F87673 Cover MACH 5433 Adaptor outside seal JT2117N552 MACH Part End confi guration Part number Female body DIN L 3V54D6X5MCH Male tip DIN L 4V14E6X5MCHA Female body DIN L 3V54D6X4MCH Male tip DIN L 4V14E6X4MCHA MACH MACH MACH MACH F87673 JT2117N552 Female body Male tip MACH MACH Parker Hannifin

54 Appendices Fluid compatibility chart Fluid compatibility chart The following seal compound and body material compatibility chart is provided as an aid in selecting a specifi c synthetic rubber compound or body material for a particular application. Shown here is a list of the seal materials available, with their temperature ranges and the corresponding Parker seal code. Operating and environmental conditions must be considered when making the selection of a quick coupling. Code used in the part Seal material Temperature range number Without NBR: Nitrile C W EPDM: Ethylene Propylene C Y FKM: Viton C Z CR: Neoprene C To indicate a special material just add the appropriate code letter as a suffix to the part number of the coupler. It is not necessary to use the code "STD" as the standard NBR ( Nitrile Butadienne Rubber) seal will be used. For recommendations for media not listed here, please contact your Parker representative. Note : This chart is intended as a guide only and is not to be considered as a recommendation to use Parker quick couplings in a specifi c application or with a specific fluid. Other factors that must be considered include but are not limited to: fl uid and ambient temperature, system pressure, both operating and peaks, frequency of connection and disconnection, and applicable standards or regulations. Codes: 1 = satisfactory 2 = fair 3 = not recommended 4 = insuffi cient data available Media Body material Seal material Brass Steel 316 S.S. 33 S.S. NBR (Nitrile) EPDM (EP) FKM (Viton TM ) CR ( Neoprene) 3M FC Acetamide Acetic acid (5%) Acetone Acetophenone Acetyl acetone Acetyl chloride Acetylene Air (1 C) Air (15 C) Air (2 C) Aluminium acetate Aluminium bromide Aluminium chloride (1%) Aluminium chloride (1%) Aluminium fluoride Aluminium nitrate Aluminium salts Aluminium sulphate Alums (NH3, Cr, K) Ammonia (anhydrous) Ammonia (cold, gas) Ammonia (hot, gas) Ammonium carbonate Ammonium chloride Ammonium hydroxide Ammonium nitrate Ammonium persulfate solution Ammonium phosphate (Mono-, Di-, Tri-basic) Ammonium salts Ammonium sulphate Amyl borate Amyl chloride Amyl chloronaphtalene Parker Hannifin

55 Appendices Fluid compatibility chart Media Body material Seal material Brass Steel 316 S.S. 33 S.S. NBR (Nitrile) EPDM (EP) FKM (Viton TM ) CR ( Neoprene) Amyl naphthalene Animal oil (lard oil) Aroclor Aroclor Aroclor Aromatic fuel -5% Arsenic acid Asphalt ASTM oil, n ASTM oil, n ASTM oil, n ASTM oil, n ASTM reference fuel A ASTM reference fuel B ASTM reference fuel C Automotive brake fluid Barium chloride Barium hydroxide Barium salts Barium sulphide Beer Beet sugar liquors Benzaldehyde Benzene Benzenesulfonic acid (1%) Benzine Benzoic acid Benzyl alcohol Benzyl chloride Bleach liquor Borax Bordeaux mixture Boric acid Brake fluid (non-petroleum) Brine (sodium chloride) Bromine Bromine water Bunker oil Butadiene (monomer) Butane Butane (2.2 & 2.3-dimethyl) Butanol (butyl alcohol) Butter (animal fat) Butyl butyrate Butyl stearate Calcine liquors Calcium acetate Calcium bisulphite Calcium carbonate Calcium chloride Calcium hydroxide Calcium hypochlorite Calcium salts Calcium sulphide Caliche liquors Cane sugar liquors Carbon bisulphide Carbon dioxide Carbon disulfide Carbon monoxide Carbon tetrachloride Parker Hannifin

56 Appendices Fluid compatibility chart Media Body material Seal material Brass Steel 316 S.S. 33 S.S. NBR (Nitrile) EPDM (EP) FKM (Viton TM ) CR ( Neoprene) Carbon acid Castor oil Celluguard Cellulube (now fyrquel) China wood oil (Tung oil) Chlorinated salt brine Chlorinated solvents Chlorobenzene Chlorobutadiene Chloroform Chlorophenol Coconut oil Copper chloride Copper salts Copper sulphate Corn oil Cottonseed oil Creosols Creosote Cresylic acid Crude oil Cutting oil Decane Denatured alcohol Detergent (water solution) Diesel fuel Diethylene glycol Dimethyl formamide Dow chemical HD Dow corning 2, 51, Dowtherm A, E Ethanol Ethyl chloride Ethyl hexanol Ethylene dichloride Ethylene glycol Fatty acids Freon Freon Freon Fuel oil Gallic acid Gas, liquid, propane (LPG) Gas, natural Gasoline / petrol Gelatine Glucose Glycerine (glycerol) Glycols Green sulphate liquor Gulf FR fluid emulsion Gulf FR fluid G Gulf FR fluid P Helium Heptane Hydraulic oil (petroleum base) Hydraulic oil (water base) Hydrazine Hydrogen gas Hydrolube Iso octane Parker Hannifin

57 Appendices Fluid compatibility chart Media Body material Seal material Brass Steel 316 S.S. 33 S.S. NBR (Nitrile) EPDM (EP) FKM (Viton TM ) CR ( Neoprene) Isobutyl alcohol Isopropyl alcohol Isopropyl ether JP3 and JP Kerosene Lard (animal fat) Linseed oil Lubricating oil SAE 1, 2, 3, 4, Magnesium salts Magnesium sulphate Mercury Methane Methanol Methyl bromide Methyl chloride (wet) Methyl chloride (dry) Methyl ether Methyl ethyl ketone (MEK) MIL-F81912 (JP-9) MIL-H MIL-H MIL-H MIL-H-8446 (MLO-8515) MIL-L-214 & 214B MIL-L Milk Mineral oils MLO-7277 and MLO Mobile HF Monomethyl hydrazine Naphtha (coal or petroleum) Naphthalene Naphthenic acid Neatsfoot oil Nickel acetate Nickel chloride Nickel salts Nickel sulphate Nitrogen Nitrous oxide Octyl alcohol Olive oil Ortho-dichlorobenzene Oxalic acid Oxygen (1-2 C) Oxygen (cold) Ozone Palmitic acid Para-dichlorobenzene Parker O-Lube Peanut oil Pentane (2-3 methyl & 2-4 dimethyl) Perchloric acid - 2N Perchloroethylene Petrolatum Petroleum oil (below 12 C) Phenol Phosphoric acid (3 molar) Phosphoric acid (concentrated) Phosphorous trichloride Picric acid (molten) Parker Hannifin

58 Appendices Fluid compatibility chart Media Body material Seal material Brass Steel 316 S.S. 33 S.S. NBR (Nitrile) EPDM (EP) FKM (Viton TM ) CR ( Neoprene) Picric acid (water solution) Pine oil Plating solutions (chrome) Plating solutions (other) Pneumatic service Potassium acetate Potassium chloride Potassium cyanide Potassium dichromate Potassium hydroxide (5%) Potassium nitrate Potassium salts Potassium sulphate PRL - high temp. hydr. oil Producer gas Propane Propyl acetate Propyl alcohol Propylene Pydraul 1E Pydraul A-2 (C series) Pydraul (3 series) Pyrogard 42, 43, 53, 55 (phosphate ester) Pyrogard D Sea water (salt water) Shell irus Silicone greases Silver nitrate Skydrol 5 (type 2) Skydrol 7 (type 2) Soap solutions Sodium acetate Sodium bicarbonate Sodium bisulphate or bisulphite Sodium borate Sodium carbonate Sodium chloride Sodium cyanide Sodium hydroxide Sodium hydroxide (5%) Sodium metaphosphate Sodium nitrate Sodium perborate Sodium peroxide Sodium phosphates Sodium salts Sodium sulphate Sodium sulphite & sulphide Sodium thiosulphate Soybean oil Stannous chloride (15 %) Steam (below 2 C) Stoddard solvents Sucrose solutions Sulphur Sulphur liquors Sulphur (molten) Sulphur dioxide (dry) Sulphur trioxide (dry) Sunsafe Tannic acid (1%) Parker Hannifin

59 Appendices Fluid compatibility chart Media Body material Seal material Brass Steel 316 S.S. 33 S.S. NBR (Nitrile) EPDM (EP) FKM (Viton TM ) CR ( Neoprene) Tar (bituminous) Tartaric acid Terpineol Tertiary butyl alcohol Tetrachloroethane Tetrachloroethylene Tetraethyl lead Tetraethyl lead (blend) Titanium tetrachloride Toluene Transformer oil Transmission fluid (type A) Trichloroethane Trichloroethylene Tricresyl phosphate Turbine oil #15 (MIL-L-788A) Turpentine Varnish Water Whiskey Wine Wood oil Xylene Zinc sulphate Parker Hannifin

60 Appendices Safety guide SAFETY GUIDE FOR SELECTING AND USING QUICK ACTION COUPLINGS AND RELATED ACCESSORIES DANGER: failure or improper selection or improper use of quick action couplings or related accessories can cause death, personal injury and property damage. Possible consequences of failure or improper selection or improper use of quick action couplings or related accessories include but are not limited to: Couplings or parts thrown off at high speed High velocity fluid discharge Contact with suddenly moving or falling objects that are to be held in position or moved by the conveyed fl uid Dangerously whipping hose Explosion or burning of the conveyed fl uid Contact with conveyed fl uids that may be hot, cold, toxic, or otherwise injurious Sparking or explosion while paint or fl ammable liquid spraying Before selecting or using any Parker quick action couplings or related accessories, it is important that you read and follow the following instructions. 1. GENERAL INSTRUCTIONS 1.1 Scope: this safety guide provides instructions for selecting and using (including installing connecting, disconnecting, and maintaining) quick action couplings and related accessories (including caps, plugs, blow guns). This safety guide is a supplement to and is to be used with the specific Parker publications for the specifi c quick action couplings and related accessories that are being considered for use. 1.2 Fail-Safe: quick action couplings or the hose they are attached to can fail without warning for many reasons. Design all systems and equipment in a fail-safe mode, so that failure of the quick action coupling or hose will not endanger persons or property. 1.3 Distribution : provide a copy of this safety guide to each person who is responsible for selecting or using quick action coupling products. Do not select or use quick action couplings without thoroughly reading and understanding this safety guide as well as the specifi c Parker publications for the products considered or selected. 1.4 User responsibility: due to the wide variety of operating conditions and uses for quick action couplings, Parker and its distributors do not represent or warrant that any particular quick action coupling is suitable for any specifi c end use system. This safety guide does not analyse all technical parameters that must be considered in selecting a product. The user, through its own analysis and testing, is solely responsible for: Making the final selection of the quick action couplings. Assuring that the user s requirements are met and that the use presents no health or safety hazards. Providing all appropriate health and safety warnings on the equipment on which the quick action couplings are used. 1.5 Additional questions: call the appropriate Parker customer service department if you have any questions or require any additional information. For the telephone numbers of the appropriate customer service department, see the Parker publication for the product being considered or used. 2. QUICK ACTION COUPLINGS SELECTION INSTRUCTIONS 2.1 Pressure: quick action couplings selection must be made so that the published rated pressure of the coupling is equal to or greater than the maximum system pressure. Pressure surges in the system higher than the rated pressure of the coupling will shorten the quick action coupling s life. Do not confuse burst pressure or other pressure values with rated pressure and do not use burst pressure or other pressure values for this purpose. 2.2 Fluid compatibility: quick action couplings selection must assure compatibility of the body and seal materials with the fl uid media used. See the fluid compatibility chart. 2.2 Temperature: be certain that fl uid and ambient temperatures, both steady and transient, do not exceed the limitations of the quick action couplings. Use caution and hand protection when connecting or disconnecting quick action couplings that are heated or cooled by the media they are conducting or by their environment. 2.4 Size: transmission or power by means of pressurised liquid varies with pressure and rate of fl ow. The size of the quick action couplings and other components of the system must be adequate to keep pressure losses to a minimum and avoid damage due to heat generation or excessive fluid velocity. 2.5 Pressurised connection or disconnection: if connecting or disconnecting under pressure is a requirement, use only quick action couplings designed for that purpose. The rated operating pressure of a quick action coupling may not be the pressure at which it may be safely connected or disconnected. 2.6 Environment: care must be taken to ensure that quick action couplings are either compatible with or protected from the environment (that is, surrounding conditions) to which they are exposed. Environmental conditions including but not limited to ultraviolet radiation, ozone, moisture, water, salt water, chemicals, and air pollutants can cause degradation and premature failure. 58 Parker Hannifin

61 Appendices Safety guide 2.7 Locking means: ball locking quick action couplings can unintentionally disconnect if they are dragged over obstructions on the end of a hose or if the sleeve is bumped or moved enough to cause disconnection. Sleeves designed with fl anges to provide better gripping for oily or gloved hands are especially susceptible to accidental disconnection and should not be used where these conditions exist. Sleeve lock or union (threaded) sleeve designs should be considered where there is a potential for accidental uncoupling. 2.8 Mechanical loads: external forces can signifi cantly reduce quick action couplings life or cause failure. Mechanical loads which must be considered include excessive tensile or side loads, and vibration. Unusual applications may require special testing prior to quick action couplings selection. 2.9 Specifications and standards: when selecting quick action couplings, government, industry, and Parker specifi cations must be reviewed and followed as applicable. 2.1 Vacuum: not all quick action couplings are suitable or recommended for vacuum service. Quick action couplings used for vacuum applications must be selected to ensure that the quick action couplings will withstand the vacuum and pressure of the system Fire resistant fluids: some fi re resistant fl uids require seals other than the standard NBR (nitrile) used in many quick action couplings Radiant heat: quick action couplings can be heated to destruction or loss of sealing without contact by such nearby items as hot manifolds or molten metal. The same heat source may then initiate a fi re. This can occur despite the presence of cool air around the quick action couplings Welding and brazing: heating of plated parts, including quick action couplings and port adapters, above 45 F (232 C) such as during welding, brazing, or soldering may emit deadly gases and may cause coupling seal damage. 3. QUICK ACTION COUPLINGS INSTALLATION INSTRUCTIONS 3.1 Pre-installation inspection: before installing a quick action coupling, visually inspect it and check for correct style, body material, seal material, and catalogue number. Before fi nal installation, coupling halves should be connected and disconnected with a sample of the mating half with which they will be used. 3.2 Quick action coupling halves from other manufacturers: if a quick action coupling assembly is made up of one Parker half and one half from another manufacturer, the lowest pressure rating of the two halves should not be exceeded. 3.3 Fitting installation: use a thread sealant, when assembling taper pipe thread joints in quick action couplings. Be sure the sealant is compatible with the system fl uid or gas. To avoid system contamination, use a liquid or paste type sealant rather than a tape style. Use the flats provided to hold the quick action coupling when installing fi ttings. Do not use pipe wrenches or a vice on other parts of the coupling to hold it when installing or a removing fi ttings as damage or loosening of threaded joints in the coupling assembly could result. Do not apply excessive torque to taper pipe threads because cracking or splitting of the female component can result. 3.4 Caps and plugs: use dust caps and plugs when quick action couplings are not coupled to exclude dirt and contamination and to protect critical surfaces from damage. 3.5 Coupling location: locate quick action couplings where they can be reached for connection or disconnection without exposing the operator to slipping, falling, getting sprayed, or coming in contact with hot or moving parts. 3.6 Hose whips: use a hose whip (a short length of hose between the tool and the coupling half) instead of rigidly mounting a coupling half on hand tools or other devices. This reduces the potential for coupling damage if the tool is dropped and provides some isolation from mechanical vibration which could cause uncoupling. 4. QUICK ACTION COUPLINGS MAINTENANCE INSTRUCTIONS 4.1 Even with proper selection and installation, quick action coupling life may be signifi cantly reduced without a continuing maintenance program. Frequency should be determined by the severity of the application and risk potential. A maintenance program must be established and followed by the user and must include the following as a minimum: 4.2 Visual inspection of quick action couplings: any of the following conditions require immediate shut down and replacement of the quick action coupling: Cracked, damaged, or corroded quick action couplings parts. Leaks at the fitting, valve or mating seal. Broken coupling mounting hardware, especially breakaway clamps. 4.3 Visual inspection all other: Leaking seals or port connections. Excess dirt build-up on the coupling locking means or on the interface area of either coupling half. Defective clamps, guards, and shields. System fluid level, fl uid type and any entrapment. 4.4 Functional test: operate the system at maximum operating pressure and check for possible malfunctions and freedom from leaks. Personnel must avoid potential hazardous areas while testing and using the system. 4.5 Replacement intervals: specifi c replacement intervals must be considered based on previous service life, government or industry recommendations, or when failures could result in unacceptable downtime, damage or injury risk. See instruction 1.2 above. 59 Parker Hannifin

62 Appendices Conversion table Dimensions Size of Tube O/D Tube O/D the unit mm inch 4 6 1/ / / / / / / / Dimensions In (") x 25.4 = mm mm 25.4 = In (") Weight Flow rate Weight Weight in LB x = Weight in grams Weight in grams = Weight in LB l/min UK GPM US GPM Flow rate l/min x = gal/min (UK) l/min x = gal/min (US) Pressure Bar MPa PSI Pressure bar x = PSI 1 MPa = 1 bars Material Designations used NF. EN in the catalogue Numerical Symbolical AISI X5 Cr Ni 18-1 AISI X8 Cr Ni S 18-9 AISI X5 Cr Ni Mo AISI 316 L X2 Cr Ni Mo AISI 316 L X2 Cr Ni Mo Parker Hannifin

63 Appendices Conversion table Temperature F C F C C F C F Temperature ( C x 1.8) + 32 = F ( F - 32) 1.8 = C Assembly torque BSPP thread (ISO / DIN 3852-T2) O-Ring with Retaining Ring Thread Series Tube O/D Assembly torque G mm Nm +1% - G 1/8A L 6 18 G 1/4A L 8 35 L 1 35 G 3/8A L 12 7 G 1/2A L 15 9 L 18 9 G 3/4A L G 1A L G 1 1/4A L G 1 1/2A L G 1/4A S 6 55 S 8 55 G 3/8A S 1 8 S 12 8 G 1/2A S S G 3/4A S 2 18 G 1A S G 1 1/4A S 3 45 G 1 1/2A S Note : Lubricate threads before assembly. Tightening torques are for steel fi ttings assembled in steel components. 61 Parker Hannifin

64 Appendices Conversion table Metric thread (ISO 6149 / DIN T3) Series Thread Assembly torque mm Nm +1% - L M8x1 8 L M1x1 15 L M12x L M14x L M16x1.5 4 L M18x L M22x1.5 6 L M27x2 1 L M33x2 16 L M42x2 21 L M48x2 26 L M6x2 315 S M8x1 1 S M1x1 2 S M12x S M14x S M16x S M18x1.5 7 S M22x1.5 1 S M27x2 17 S M33x2 31 S M42x2 33 S M48x2 42 S M6x2 5 Note : Lubricate threads before assembly. Tightening torques are for steel fi ttings assembled in steel components. NPTF thread Thread TFFT* inch 1/ / / / / / /4-11 1/ /2-11 1/ / * Turn From Finger Tight: The proper method of assembling tapered threaded connectors is to assemble them fi nger tight and then wrench tighten further to the specified number of turns from fi nger tight (TFFT). Assembly Turns From Finger Tight values for steel, stainless steel and brass fittings. UNF thread (SAE J 1926/1, ISO 11926) Size of Thread Assembly torque the unit inch Nm +1% - 2 5/16-24 UNF - 2B 1 3 3/8-24 UNF - 2B /16-2 UNF - 2B /2-2 UNF - 2B 3 6 9/16-18 UNF - 2B /4-16 UNF - 2B /8-14 UNF - 2B /16-12 UN - 2B /16-12 UN - 2B /16-12 UN - 2B /8-12 UN - 2B /8-12 UN - 2B /2-12 UN - 2B Parker Hannifin

65 Appendices Alpha numeric index Part number Page Part number Page Part number Page Part number Page Part number Page P P P P V54D6X4MCH V54D6X5MCH B B P P P B B P P P F2C O14GZ4-B O14G4X4-B O54GZ4-B O54G4X4-B V13D6X2-B V13D6X3-B V13D7X3-B V13E6X3-B V13F4B3-B V13G4X3-B V14D6X2-B V14D6X3-B V14D6X4-B V14D6X5-B V14D6X6-B V14D7X3-B V14D7X6-B V14E6X2-B V14E6X3-B V14E6X4-B V14E6X4MCHA V14E6X5-B V14E6X5MCHA V14E6X6-B V14E7X3-B V14E7X4-B V14E7X6-B V14F4B3-B V14F4B4-B V14G4X3-B V14G4X4-B V14G4X6-B V14G8X5-B V14G8X6-B V53D6X2-B V53D6X3-B V53D7X3-B V53E6X3-B V53F4B3-B V53G4X3-B V53-KIT V54D6X2-B V54D6X3-B V54D6X4-B V54D6X5-B V54D6X6-B V54D7X3-B V54D7X6-B V54E6X2-B V54E6X3-B V54E6X4-B V54E6X5-B V54E6X6-B V54E7X3-B V54E7X4-B V54E7X6-B V54F4B3-B V54F4B4-B V54G4X3-B V54G4X4-B V54G4X6-B V54G8X5-B V54G8X6-B V54-KIT V54-KIT P P PR P PR P M M M M M M M M M M PL PL PL PL PL PL PL PL PL PL E6Z5S F8H6S T5X4S B J N R V...37 BH12-6L...1 BH12-6L-BSPP...1 BH12-6N...1 BH12-6N-BSPP...1 BH12-61L...1 BH12-61L-BSPP...1 BH12-61N...1 BH12-61N-BSPP...1 BH BH1-6-BSPP...1 BH BH1-61-BSPP...1 BH BH216-6-BSPP...1 BH BH BSPP...1 BH BH2-6-BSPP...1 BH BH2-61-BSPP...1 BH BH3-6-BSPP...1 BH BH3-61-BSPP...1 BH BH4-6-BSPP...1 BH BH4-61-BSPP...1 BH BH6-6-BSPP...1 BH BH6-61-BSPP...1 BH BH8-6-BSPP...1 BH BH8-61-BSPP...1 CFE-12-P CFE-252-P CFE-372-P CFE-52-P CFE-622-P CFE-752-P CL-251-4FB-PLP...24 CL-252-4FB-PLC...24 CM-251-4FB-PLP...22 CM-252-4FB-PLC...22 CPC CPP DCP DCP DCP DCP DFE-51-P FEF-11-2FB...14 FEF-12-2FB...14 FEF-251-4FB...14 FEF-252-4FB...14 FEF-371-6FB...14 FEF-371-8FB...14 FEF-372-6FB...14 FEF-372-8FB...14 FEF-51-12FB...14 FEF-51-8FB...14 FEF-52-12FB...14 FEF-52-8FB...14 FEF FB...14 FEF FB...14 FEF FB...14 FEF FB...14 FEM-11-2FB...17 FEM-12-2FB...17 FEM-251-4FB...17 FEM-252-4FB...17 FEM BMCL...18 FEM MCL...17 FEM BMCL...18 FEM MCL...17 FEM BMCL...18 FEM MCL...17 FEM-371-6FB...17 FEM-371-8FB...17 FEM BMCL...18 FEM MCL...17 FEM BMCL...18 FEM MCL...17 FEM BMCL...18 FEM MCL...17 FEM-372-6FB...17 FEM-372-8FB...17 FEM-51-12FB...17 FEM-51-18BMCL...18 FEM-51-18MCL...17 FEM-51-22BMCL...18 FEM-51-22MCL...17 FEM-51-8FB...17 FEM-52-12FB...17 FEM-52-18BMCL...18 FEM-52-18MCL...17 FEM-52-22BMCL...18 FEM-52-22MCL...17 FEM-52-8FB...17 FEM FB...17 FEM FB...17 FEM FB...17 FEM FB...17 H12-62L...7 H12-62L-BSPP...7 H12-62N...7 H12-62N-BSPP...7 H12-63L...7 H12-63L-BSPP Parker Hannifin

66 Appendices Alpha numeric index Part number Page Part number Page Part number Page Part number Page Part number Page H12-63N...7 H12-63N-BSPP...7 H H H H1-62-BSPP...7 H H1-63-BSPP...7 H H1-65M H H1-66M H H BSPP...7 H H BSPP...7 H H H H2-62-BSPP...7 H H2-63-BSPP...7 H H2-65M H H2-66M H H3-62-BSPP...7 H H3-63-BSPP...7 H H3-65M H H3-66M H H4-62-BSPP...7 H H4-63-BSPP...7 H H4-65M H H4-66M H H6-62-BSPP...7 H H6-63-BSPP...7 H H6-65M H H6-66M H67A H67C H H8-62-BSPP...7 H H8-63-BSPP...7 H H8-65M H H8-66M JT1U QE...26 JT213N JT213V JT215N JT215V JT2112N JT2114N JT2115N JT2116N JT2116V JT2117N JT2123N JT2126N JT2211N JT2213N JT2213V JT2218N JT2218V JT2222N JT2222V JT2224N JT2333N LV14E6X5MLX...47 LV54D6X5MLXC...47 MACH MACH MACH MACH MACH MACH MACH A...51 MACH F MACH2-IA-B...47 MACH2-IA-P...47 MACH4/715LB...5 MACH4/715LBE...5 MACH4/715LT...5 MACH4/715LTE...5 MACH5/715LB...5 MACH5/715LBE...5 MACH5/715LT...5 MACH5/715LTE...5 MACH6/715LB...5 MACH6/715LBE...5 MACH6/715LT...5 MACH6/715LTE...5 MACH7B...5 MACH7T...5 NSI MCL...2 NSI-251-C16MCL...2 NSI-252-4MBE...2 PFE-11-P PFE-251-P PFE-371-P PFE-51-P PFE-621-P PFE-751-P QHPA13-D6X2-B...43 QHPA13-D6X3-B...43 QHPA13-D7X3-B...43 QHPA13-D7X4-B...43 QHPA13-DC...44 QHPA13-E6X2-B...43 QHPA13-E6X3-B...43 QHPA13-E7X3-B...43 QHPA13-E7X4-B...43 QHPA13-F4A3-B...44 QHPA13-G4X3-B...44 QHPA14-D6X4-B...43 QHPA14-D6X5-B...43 QHPA14-D7X5-B...43 QHPA14-D7X6-B...43 QHPA14-DC...44 QHPA14-E6X4-B...43 QHPA14-E6X5-B...43 QHPA14-E7X6-B...43 QHPA14-F4A4-B...44 QHPA14-G4X4-B...44 QHPA16-D6X6-B...43 QHPA16-D6X7-B...43 QHPA16-D7X7-B...43 QHPA16-D7X8-B...43 QHPA16-DC...44 QHPA16-E6X6-B...43 QHPA16-E7X7-B...43 QHPA16-E7X8-B...43 QHPA16-G4X6-B...44 QHPA16-G4X8-B...44 QHPA18-D7X9-B...43 QHPA18-DC...44 QHPA18-E7X9-B...43 QHPA53-D6X2-B...43 QHPA53-D6X3-B...43 QHPA53-D7X3-B...43 QHPA53-D7X4-B...43 QHPA53-DP...44 QHPA53-E6X2-B...43 QHPA53-E6X3-B...43 QHPA53-E7X3-B...43 QHPA53-E7X4-B...43 QHPA53-F4A3-B...44 QHPA53-G4X3-B...44 QHPA53-KIT...44 QHPA54-D6X4-B...43 QHPA54-D6X5-B...43 QHPA54-D7X5-B...43 QHPA54-D7X6-B...43 QHPA54-DP...44 QHPA54-E6X4-B...43 QHPA54-E6X5-B...43 QHPA54-E7X6-B...43 QHPA54-F4A4-B...44 QHPA54-G4X4-B...44 QHPA54-KIT...44 QHPA56-D6X6-B...43 QHPA56-D6X7-B...43 QHPA56-D7X7-B...43 QHPA56-D7X8-B...43 QHPA56-DP...44 QHPA56-E6X6-B...43 QHPA56-E7X7-B...43 QHPA56-E7X8-B...43 QHPA56-G4X6-B...44 QHPA56-G4X8-B...44 QHPA56-KIT...44 QHPA58-D7X9-B...43 QHPA58-DP...44 QHPA58-E7X9-B...43 QHPA58-KIT...44 SH12-62N...8 SH12-62N-BSPP...8 SH12-63N...8 SH12-63N-BSPP...8 SH SH1-62-BSPP...8 SH SH1-63-BSPP...8 SH SH2-62-BSPP...8 SH SH2-63-BSPP...8 SH SH3-62-BSPP...8 SH SH3-63-BSPP...8 SH SH4-62-BSPP...8 SH SH4-63-BSPP...8 SH SH6-62-BSPP...8 SH SH6-63-BSPP...8 SH SH8-62-BSPP...8 SH SH8-63-BSPP...8 SSH1-62Y...9 SSH1-62Y-BSPP...9 SSH1-63Y...9 SSH1-63Y-BSPP...9 SSH2-62Y...9 SSH2-62Y-BSPP...9 SSH2-63Y...9 SSH2-63Y-BSPP...9 SSH3-62Y...9 SSH3-62Y-BSPP...9 SSH3-63Y...9 SSH3-63Y-BSPP...9 SSH4-62Y...9 SSH4-62Y-BSPP...9 SSH4-63Y...9 SSH4-63Y-BSPP...9 SSH6-62Y...9 SSH6-62Y-BSPP...9 SSH6-63Y...9 SSH6-63Y-BSPP...9 SSH8-62Y...9 SSH8-62Y-BSPP...9 SSH8-63Y...9 SSH8-63Y-BSPP Parker Hannifin

67 Parker Hannifin Corporation About Parker Hannifin Corporation Parker Hannifi n is a leading global motion-control company dedicated to delivering premier customer service. A Fortune 5 corporation listed on the New York Stock Exchange (PH), our components and systems comprise over 1,4 product lines that control motion in some 1, industrial and aerospace markets. Parker is the only manufacturer to offer its customers a choice of hydraulic, pneumatic, and electro mechan ical motion-control solutions. Our Company has the largest distribution network in its fi eld, with over 7,5 distributors serving nearly 4, customers worldwide. Parker s Charter To be a leading worldwide manufacturer of components and systems for the builders and users of durable goods. More specifi cally, we will design, market and manufacture products controlling motion, fl ow and pressure. We will achieve profi table growth through premier customer service. Product Information Customers seeking product infor mation, the location of a nearby distributor, or repair services will receive prompt attention by calling the Parker Product Information Centre. The Centre can be called toll free from France, Germany, Austria, Switzerland or the United Kingdom. You will be answered by a Parker employee in your own language. Call Freephone: (8 C PARKER). The Aerospace Group is a leader in the development, design, manufacture and servicing of control systems and components for aerospace and related high- technology markets, while achieving growth through premier customer service. The Climate & Industrial Controls Group designs, manufactures and markets system-control and fl uidhandling components and systems to refrigeration, air-conditioning and industrial customers worldwide. The designs, manu factures and markets rigid and flexible connectors, and associated products used in pneumatic and fluid systems. The Seal Group designs, manufactures and distributes industrial and commercial sealing devices and related products by providing superior quality and total customer satisfaction. The Hydraulics Group designs, produces and markets a full spectrum of hydraulic com ponents and systems to builders and users of industrial and mobile machinery and equipment. The Filtration Group designs, manufactures and markets quality fi ltration and clarifi cation products, providing customers with the best value, quality, technical support, and global availability. The Automation Group is a leading supplier of pneumatic and electromechanical components and systems to automation customers worldwide. The Instrumentation Group is a global leader in the design, manufacture and distribution of high-quality critical fl ow components for worldwide process instrumentation, ultra-high-purity, medical and analytical applications.