Concept Evaluation and Optimization of a 2-Stage Charging System

Size: px
Start display at page:

Download "Concept Evaluation and Optimization of a 2-Stage Charging System"

Transcription

1 Concept Evaluation and Optimization of a 2-Stage Charging System GT Conference 2014, OCTOBER Msc. ETH Pascal Mühlebach, Dr. sc. techn. Christian Lämmle combustion and flow solutions GmbH, Zurich Dipl. Ing. ETH Daniel Gohl, Dipl. Ing. Peter Fledersbacher sa-, Mellingen Dipl. Ing. Peter Obrecht, Prof. Dr. sc. techn. Konstantinos Boulouchos Aerothermochemistry and Combustion Systems Laboratory LAV, Swiss Federal Institute of Technology, ETH Zurich 1

2 Content Project Overview Investigated 2-Stage Charging Systems Methodology of Optimization Process Results Conclusions & Outlook 2

3 Project Overview: Objectives Develop and design a 2-stage charging system for 2.0L 4-cylinder diesel engine flight application up to ft / 7620m (p Amb =0.36bar, T Amb =-35 C /238K) power 3900rpm (target full load from rpm) max cylinder pressure 165bar minimize fuel consumption Estimation of resulting pressure ratio η e = 0.32, λ = 1.3, n = 3900rrr, P = 100kW Ground p AAA = 1.00bar, T AAA = 293K, T III_eee = 350K p III = 2.2bbb π = 2.2 Maaaaaa aaaaaaaa p AAA = 0.36bar, T AAA = 238K, T III_eee = 300K p III = 1.9bbb π = 5.3 3

4 Project: Structure and Partners Optimize the charging system through simulation Develop an universally applicable optimization tool Compare and optimize different charging concepts with GT-POWER Demonstrator of optimized charging system Support engineering / provide TC maps Build a prototype and demonstrate usability Phenomenological Models Enhance existing models for burn rate, NOx and soot Together with CFS: Implement the models into GT- POWER by means of user coding The project is funded by the Swiss Erdöl-Vereinigung 4

5 Content Project Overview Investigated 2-Stage Charging Systems Methodology of Optimization Process Results Conclusions & Outlook 5

6 Investigated 2-Stage Charging Systems System 1: MC + TC System 2: TC + TC IC IC High Pressure mechanically driven compressor IC Low Pressure turbocharger Wastegate High Pressure turbocharger IC Low Pressure turbocharger Wastegate Optimization Parameters Mass Flow Multiplier LP Compressor Mass Flow Multiplier LP Turbine Mass Flow Multiplier HP Compressor Gear Ratio Optimization Parameters Mass Flow Multiplier LP Compressor Mass Flow Multiplier LP Turbine Mass Flow Multiplier HP Compressor Mass Flow Multiplier HP Turbine 6

7 Content Project Overview Investigated 2-Stage Charging Systems Methodology of Optimization Process Results Conclusions & Outlook 7

8 Optimization: Methodology Define optimization goal Choose optimization algorithm (PSO, GA) Define parameters Define constraints Write parameter file Start GT-POWER Analyse results Define new parameters Write output file 8

9 Optimization: Mass Flow Multiplier as a Function of Iteration 9

10 Content Project Overview Investigated 2-Stage Charging Systems Methodology of Optimization Process Results Conclusions & Outlook 10

11 Results: Brake Specific Fuel Consumption 11

12 Results: Compressor Maps MC-TC Low Pressure Compressor (TC) High Pressure Compressor (MC) TC maps provided by sa-charging solutions Considered Engine Speeds [rpm]: 2 250, 2 500, 2 750, 3 000, 3 250, 3 750,

13 Results: Compressor Maps TC-TC Low Pressure Compressor (TC) High Pressure Compressor (TC) TC maps provided by sa-charging solutions Considered Engine Speeds [rpm]: 2 250, 2 500, 2 750, 3 000, 3 250, 3 750,

14 Results: Pumping Mean Effective Pressure 14

15 Results: Maximum Cylinder Pressure 15

16 Content Project Overview Investigated 2-Stage Charging Systems Methodology of Optimization Process Results Conclusions & Outlook 16

17 Conclusions & Outlook Both investigated charging versions fulfil the power target under these challenging conditions The engine equipped with two turbochargers shows 3 to 8% lower fuel consumption lower maximum cylinder pressure The engine equipped with one mechanically driven compressor and one turbocharger has advantages in packaging (size of low pressure parts) lower weight The setups will be run again with the phenomenological models (boundaries for turbines) The engine will be tested on a test bench ( ground conditions ) 17

18 Thanks for your attention

19 Results: Temperature Before Turbine 19

20 Results: Lambda 20

21 Results: Residual Gases 21

22 Results: Turbine Maps MC-TC Low Pressure Compressor (TC) Low Pressure Turbine (TC) Considered Engine Speeds [rpm]: 2 250, 2 500, 2 750, 3 000, 3 250, 3 750,

23 Results: Turbine Maps TC-TC Low Pressure Turbine (TC) High Pressure Turbine (TC) Considered Engine Speeds [rpm]: 2 250, 2 500, 2 750, 3 000, 3 250, 3 750,

24 GT-POWER Models System 1: MC + TC System 2: TC + TC 24

25 Particle Swarm Optimization Algorithm Initialize an array of particles with random values Evaluate the desired minimization function Compare evaluation with particle s previous best value If current value < particle s best value: x l,bbbb = x(t) Compare evaluation with group s previous best value If current value < group s best value: x g,bbbb = x(t) Change velocity: v t + 1 = c 1 v(t) + c 2 r 1 x l,bbbb x t + c 3 r 2 x g,bbbb x t Change position: x t + 1 = x t + v(t + 1) Loop to step 2 and repeat until a criterion is met 25

Comparison of Soot Measurement Instruments during Transient and Steady State Operation

Comparison of Soot Measurement Instruments during Transient and Steady State Operation Comparison of Soot Measurement Instruments during Transient and Steady State Operation Christophe Barro, Philipp Vögelin, Pascal Wilhelm, Peter Obrecht, Konstantinos Boulouchos (Aerothermochemistry and

More information

Ignition- and combustion concepts for lean operated passenger car natural gas engines

Ignition- and combustion concepts for lean operated passenger car natural gas engines Ignition- and combustion concepts for lean operated passenger car natural gas engines Patrik Soltic 1, Thomas Hilfiker 1 Severin Hänggi 2, Richard Hutter 2 1 Empa, Automotive Powertrain Technologies Laboratory,

More information

Impact of the Operation Strategy and Fuel Composition on the Emissions of a Heavy-Duty Diesel Engine

Impact of the Operation Strategy and Fuel Composition on the Emissions of a Heavy-Duty Diesel Engine Impact of the Operation Strategy and Fuel Composition on the Emissions of a Heavy-Duty Diesel Engine Dr. C. Barro LAV / Vir2sense M. Parravicini LAV Prof. Dr. Boulouchos LAV www.vir2sense.com Outline Motivation

More information

Determination of a turbocharged gasoline engine for hybrid powertrains. F. Kercher,

Determination of a turbocharged gasoline engine for hybrid powertrains. F. Kercher, Determination of a turbocharged gasoline engine for hybrid powertrains F. Kercher, 26.10.2015 Determination of a turbocharged gasoline engine for hybrid powertrains Agenda Introduction Hybrid Electric

More information

DEVELOPMENT OF A VIRTUAL SOOT SENSOR IN DIESEL ENGINES

DEVELOPMENT OF A VIRTUAL SOOT SENSOR IN DIESEL ENGINES RESEARCH ENGINE MANAGEMENT AUTHORS DEVELOPMENT OF A VIRTUAL SOOT SENSOR IN DIESEL ENGINES DR. CHRISTOPHE BARRO is Research Assistant at the Aerothermochemistry and Combustion Systems Laboratory (LAV) at

More information

GT-Suite Users Conference

GT-Suite Users Conference GT-Suite Users Conference Thomas Steidten VKA RWTH Aachen Dr. Philip Adomeit, Bernd Kircher, Stefan Wedowski FEV Motorentechnik GmbH Frankfurt a. M., October 2005 1 Content 2 Introduction Criterion for

More information

C. Christen, D. Brand, CIMAC 2013 Simulation-based study on turbocharging dual-fuel engines Paper no. 187

C. Christen, D. Brand, CIMAC 2013 Simulation-based study on turbocharging dual-fuel engines Paper no. 187 C. Christen, D. Brand, CIMAC 2013 Simulation-based study on turbocharging dual-fuel engines Paper no. 187 Dual-fuel engines As a solution for IMO Tier III GAS MODE Low NO x emission NO x Level < IMO Tier

More information

Scaling Functions for the Simulation of Different SI-Engine Concepts in Conventional and Electrified Power Trains

Scaling Functions for the Simulation of Different SI-Engine Concepts in Conventional and Electrified Power Trains Scaling Functions for the Simulation of Different SI-Engine Concepts in Conventional and Electrified Power Trains Dipl.-Ing. Michael Huß BMW Group (05/2007 04/2010) Prof. Dr.-Ing Georg Wachtmeister LVK

More information

FLUID DYNAMICS TRANSIENT RESPONSE SIMULATION OF A VEHICLE EQUIPPED WITH A TURBOCHARGED DIESEL ENGINE USING GT-POWER

FLUID DYNAMICS TRANSIENT RESPONSE SIMULATION OF A VEHICLE EQUIPPED WITH A TURBOCHARGED DIESEL ENGINE USING GT-POWER GT-SUITE USERS CONFERENCE FRANKFURT, OCTOBER 20 TH 2003 FLUID DYNAMICS TRANSIENT RESPONSE SIMULATION OF A VEHICLE EQUIPPED WITH A TURBOCHARGED DIESEL ENGINE USING GT-POWER TEAM OF WORK: A. GALLONE, C.

More information

Boosting the Starting Torque of Downsized SI Engines GT-Suite User s Conference 2002

Boosting the Starting Torque of Downsized SI Engines GT-Suite User s Conference 2002 GT-Suite User s Conference 2002 Hans Rohs Inst. For Combustion Engines (VKA) RWTH Aachen Knut Habermann, Oliver Lang, Martin Rauscher, Christof Schernus FEV Motorentechnik GmbH Acknowledgement: Some of

More information

Holistic 1D-Model for Cooling Management and Engine Analysis of a Heavy-Duty Truck

Holistic 1D-Model for Cooling Management and Engine Analysis of a Heavy-Duty Truck Holistic 1D-Model for Cooling Management and Engine Analysis of a Heavy-Duty Truck Dominik Renner Dr. Alexander Schydlo 26 th October 2015 MAN Truck & Bus AG < 1 > Agenda 1 Introduction 2 Model Description

More information

Experimental Investigations of Transient Emissions Behaviour Using Engine-in-the-Loop

Experimental Investigations of Transient Emissions Behaviour Using Engine-in-the-Loop TSI.InP.P_User5.Temperature7 [degc] TSI.InP.P_User4.Temperature [degc] TSI.InP.P_User4.Temperature3 [degc] Car.v [m/s] IO.Emission.CO_ DM.Gas Car.ay [m/s^] Car.ax [m/s^] Experimental Investigations of

More information

GT Conference 2017: Simulation Tool for Predictive Control Strategies for an ORC- System in Heavy Duty Vehicles

GT Conference 2017: Simulation Tool for Predictive Control Strategies for an ORC- System in Heavy Duty Vehicles GT Conference 217: Simulation Tool for Predictive Control Strategies for an ORC- System in Heavy Duty Vehicles October 9-1, 217 Dipl.-Ing. Jörg Kreyer M.Sc. Prof. Dr.-Ing. Thomas Esch FH Aachen FH Aachen

More information

Potential of Turbocharging

Potential of Turbocharging 29119_VB_PES_GT-Suite-Coference.ppt Vincenzo Bevilacqua, PE-AB Potential of Turbocharging 11.12.28 Seite 1 von 24 29119_VB_PES_GT-Suite-Coference.ppt Vincenzo Bevilacqua, PE-AB Potential of Turbocharging

More information

Highly transient gas engine operation from a turbocharging perspective

Highly transient gas engine operation from a turbocharging perspective HERVÉ MARTIN, ABB TURBO SYSTEMS LTD Highly transient gas engine operation from a turbocharging perspective 10th CIMAC CASCADES, Kobe, 12 th October 2018 Overview Introduction Basics of load pick-up Modeling

More information

Digital Shaping and Optimization of Fuel Injection Pattern for a Common Rail Automotive Diesel Engine through Numerical Simulation

Digital Shaping and Optimization of Fuel Injection Pattern for a Common Rail Automotive Diesel Engine through Numerical Simulation Digital Shaping and Optimization of Fuel Injection Pattern for a Common Rail Automotive Diesel Engine through Numerical Simulation European GT Conference 2017 - Frankfurt am Main Politecnico di Torino:

More information

Chip Simulation for Virtual ECUs

Chip Simulation for Virtual ECUs Chip Simulation for Virtual ECUs QTronic User Conference 2018 Virtual ECUs and Applications 18th of October, Berlin, Germany Dr. Yutaka Murata Honda R&D Co., Ltd. Automotive R&D Center 1 Contents Background

More information

SCCER Mobility. Swiss Competence Center for Energy Research Efficient Technologies and Systems for Mobility

SCCER Mobility. Swiss Competence Center for Energy Research Efficient Technologies and Systems for Mobility SCCER Mobility Swiss Competence Center for Energy Research Efficient Technologies and Systems for Mobility Mission Currently, the transport sector accounts for more than one third of the total energy demand

More information

AUTOMATED CFD-SIMULATION OF A TURBOCHARGER ON A HIGH PERFORMANCE BMW DIESEL ENGINE BY USE OF DFBI M. REICHHART

AUTOMATED CFD-SIMULATION OF A TURBOCHARGER ON A HIGH PERFORMANCE BMW DIESEL ENGINE BY USE OF DFBI M. REICHHART STAR Global Conference 2016, Prague BMW Group, March 7, 2016 AUTOMATED CFD-SIMULATION OF A TURBOCHARGER ON A HIGH PERFORMANCE BMW DIESEL ENGINE BY USE OF DFBI M. REICHHART CONTENT TURBOCHARGER FORMER WORKFLOW

More information

MoBEO: Model based Engine Development and Calibration

MoBEO: Model based Engine Development and Calibration MoBEO: Model based Engine Development and Calibration Innovative ways to increase calibration quality within the limits of acceptable development effort! Dr. Prakash Gnanam, AVL Powertrain UK Ltd 1 25

More information

Analytical and Experimental Evaluation of Cylinder Deactivation on a Diesel Engine. S. Pillai, J. LoRusso, M. Van Benschoten, Roush Industries

Analytical and Experimental Evaluation of Cylinder Deactivation on a Diesel Engine. S. Pillai, J. LoRusso, M. Van Benschoten, Roush Industries Analytical and Experimental Evaluation of Cylinder Deactivation on a Diesel Engine S. Pillai, J. LoRusso, M. Van Benschoten, Roush Industries GT Users Conference November 9, 2015 Contents Introduction

More information

Whither Diesel? An Overview of Combustion Concepts and Research Directions for Compression Ignition Engines

Whither Diesel? An Overview of Combustion Concepts and Research Directions for Compression Ignition Engines An Overview of Combustion Concepts and Research Directions for Compression Ignition Engines Martin H. University of Oxford, UK FPC2015 Future Powertrain Conference National Motorcycle Museum, Solihull

More information

Kyoto a lot of talking. Copenhagen a lot of talking. We believe in action: the sustainable concept

Kyoto a lot of talking. Copenhagen a lot of talking. We believe in action: the sustainable concept Kyoto a lot of talking Copenhagen a lot of talking We believe in action: the sustainable concept PANOLIN helps you convert your machine into a green machine l Since 25 years PANOLIN ECLs* help protect

More information

Highly dynamic control of a test bench for highspeed train pantographs

Highly dynamic control of a test bench for highspeed train pantographs PAGE 26 CUSTOMERS Highly dynamic control of a test bench for highspeed train pantographs Keeping Contact at 300 km/h Electric rail vehicles must never lose contact with the power supply, not even at the

More information

GT-Suite European User Conference

GT-Suite European User Conference GT-Suite European User Conference E-Charging on a High Performance Diesel engine D. Peci, C. Venezia EMEA Region - Powertrain Engineering Powertrain Research&Technology Frankfurt, Germany October 26th,

More information

EGR Transient Simulation of a Turbocharged Diesel Engine using GT-Power

EGR Transient Simulation of a Turbocharged Diesel Engine using GT-Power GT-SUITE USERS CONFERENCE FRANKFURT, OCTOBER 4 TH 2004 EGR Transient Simulation of a Turbocharged Diesel Engine using GT-Power TEAM OF WORK: G. GIAFFREDA, C. VENEZIA RESEARCH CENTRE ENGINE ENGINEERING

More information

THE POTENTIAL OF ELECTRIC EXHAUST GAS TURBOCHARGING FOR HD DIESEL ENGINES

THE POTENTIAL OF ELECTRIC EXHAUST GAS TURBOCHARGING FOR HD DIESEL ENGINES GT-Suite Users International Conference Frankfurt a.m., October 1 th 25 THE POTENTIAL OF ELECTRIC EXHAUST GAS TURBOCHARGING FOR HD DIESEL ENGINES F. Millo, F. Mallamo, (POLITECNICO DI TORINO, ITALY) E.

More information

GT-Suite Users International Conference Frankfurt a.m., October 22 nd 2012

GT-Suite Users International Conference Frankfurt a.m., October 22 nd 2012 GT-Suite Users International Conference Frankfurt a.m., October 22 nd 2012 Computational Analysis of Internal and External EGR Strategies combined with Miller Cycle Concept for a Two Stage Turbocharged

More information

17/11/2016. Turbomachinery & Heat Transfer Laboratory Faculty of Aerospace Engineering Technion Israel Institute of Technology, Israel

17/11/2016. Turbomachinery & Heat Transfer Laboratory Faculty of Aerospace Engineering Technion Israel Institute of Technology, Israel 17/11/2016 Turbomachinery & Heat Transfer Laboratory Faculty of Aerospace Engineering Technion Israel Institute of Technology, Israel 1 Motivation New challenges rise due to increase in demands from small

More information

Performance analysis of TEGs applied in the EGR path of a heavy duty engine for a Transient Drive Cycle

Performance analysis of TEGs applied in the EGR path of a heavy duty engine for a Transient Drive Cycle Performance analysis of TEGs applied in the EGR path of a heavy duty engine for a Transient Drive Cycle Thermo-electric Group Department of Aeronautical and Automotive Engineering Prof. Richard Stobart

More information

Dynamic Behaviour of a Fuel Cell with Ultra Capacitor Peak Power Assistance for a Light Vehicle

Dynamic Behaviour of a Fuel Cell with Ultra Capacitor Peak Power Assistance for a Light Vehicle Dynamic Behaviour of a Fuel Cell with Ultra Capacitor Peak Power Assistance for a Light Vehicle Jörg Folchert, Dietrich Naunin, Sina Block Abstract The operation of a Fuel Cell inside of a vehicle is a

More information

Modeling a Phlegmatized Diesel-Engine in a Hybrid Electric Vehicle Using a Transient Predictive Model Michael Auerbach, October 25th, 2010, Frankfurt

Modeling a Phlegmatized Diesel-Engine in a Hybrid Electric Vehicle Using a Transient Predictive Model Michael Auerbach, October 25th, 2010, Frankfurt Modeling a Phlegmatized Diesel-Engine in a Hybrid Electric Vehicle Using a Transient Predictive Model Michael Auerbach, October 25th, 2010, Frankfurt a. M. Institut für Verbrennungsmotoren und Kraftfahrwesen

More information

All fuel is not the same fuel

All fuel is not the same fuel All fuel is not the same fuel Energy conversion during the combustion process is exceptionally well researched - but continues to lead to new, fascinating questions. Researchers who study engines are currently

More information

All-in-one Simulation and DoE Methodology for the Evaluation and Optimisation of HEV Configurations. W.-R. Landschoof, M. Kämpfner, Dr. M.

All-in-one Simulation and DoE Methodology for the Evaluation and Optimisation of HEV Configurations. W.-R. Landschoof, M. Kämpfner, Dr. M. All-in-one Simulation and DoE Methodology for the Evaluation and Optimisation of HEV Configurations W.-R. Landschoof, M. Kämpfner, Dr. M. Zillmer 1 Contents 1. Motivation 2. Hybrid concepts 3. Significance

More information

APPLICATION OF STAR-CCM+ TO TURBOCHARGER MODELING AT BORGWARNER TURBO SYSTEMS

APPLICATION OF STAR-CCM+ TO TURBOCHARGER MODELING AT BORGWARNER TURBO SYSTEMS APPLICATION OF STAR-CCM+ TO TURBOCHARGER MODELING AT BORGWARNER TURBO SYSTEMS BorgWarner: David Grabowska 9th November 2010 CD-adapco: Dean Palfreyman Bob Reynolds Introduction This presentation will focus

More information

Fuel Consumption, Exhaust Emission and Vehicle Performance Simulations of a Series-Hybrid Electric Non-Automotive Vehicle

Fuel Consumption, Exhaust Emission and Vehicle Performance Simulations of a Series-Hybrid Electric Non-Automotive Vehicle 2017 Published in 5th International Symposium on Innovative Technologies in Engineering and Science 29-30 September 2017 (ISITES2017 Baku - Azerbaijan) Fuel Consumption, Exhaust Emission and Vehicle Performance

More information

OPTIMIZATION STUDIES OF ENGINE FRICTION EUROPEAN GT CONFERENCE FRANKFURT/MAIN, OCTOBER 8TH, 2018

OPTIMIZATION STUDIES OF ENGINE FRICTION EUROPEAN GT CONFERENCE FRANKFURT/MAIN, OCTOBER 8TH, 2018 OPTIMIZATION STUDIES OF ENGINE FRICTION EUROPEAN GT CONFERENCE FRANKFURT/MAIN, OCTOBER 8TH, 2018 M.Sc. Oleg Krecker, PhD candidate, BMW B.Eng. Christoph Hiltner, Master s student, Affiliation BMW AGENDA

More information

Furnace-based optimisation of a lignite-fired steam generator

Furnace-based optimisation of a lignite-fired steam generator Vo lu me 9 Is sue / Pa ge to Furnace-based optimisation of a lignite-fired steam generator by Daniel Sommer, Piotr Olkowski, Dieter Rüsenberg and Heinz-Jürgen Wüllenweber VGB PowerTech l Optimisation

More information

Virtual Sensors for Diesel Engines

Virtual Sensors for Diesel Engines RESEARCH Diesel Engines Virtual Sensors for Diesel Engines To enable efficient operation while simultaneously producing low levels of exhaust emissions, modern passenger car diesel engines have significantly

More information

Vehicle simulation with cylinder deactivation

Vehicle simulation with cylinder deactivation Vehicle simulation with cylinder deactivation Potential analysis of cylinder deactivation using a detailed Cyrille Frottier, Lars Böttcher, GT-SUITE Users Conference, October 2011 Vehicle simulation with

More information

P. Teufel and A. Böhmer, ABB Turbo Systems, SIMULIA Customer Conference Thrust Collar Bearing Optimization using Isight

P. Teufel and A. Böhmer, ABB Turbo Systems, SIMULIA Customer Conference Thrust Collar Bearing Optimization using Isight P. Teufel and A. Böhmer, ABB Turbo Systems, SIMULIA Customer Conference 2012 Thrust Collar Bearing Optimization using Isight May 23, 2012 Thrust Collar Bearing Optimization Using Isight Contents Turbocharging:

More information

HYSYS System Components for Hybridized Fuel Cell Vehicles

HYSYS System Components for Hybridized Fuel Cell Vehicles HYSYS System Components for Hybridized Fuel Cell Vehicles J. Wind, A. Corbet, R.-P. Essling, P. Prenninger, V. Ravello This document appeared in Detlef Stolten, Thomas Grube (Eds.): 18th World Hydrogen

More information

Health Relevance of Aerosols from Biomass Combustion in Comparison to Diesel Soot Indicated by Cytotoxicity Tests

Health Relevance of Aerosols from Biomass Combustion in Comparison to Diesel Soot Indicated by Cytotoxicity Tests Health Relevance of Aerosols from Biomass Combustion in Comparison to Diesel Soot Indicated by Cytotoxicity Tests Norbert Klippel, Thomas Nussbaumer, Michael Oser, Zurich (Switzerland), www.verenum.ch

More information

OME Vorstellung. Introduction, Overview. Technical University of Munich Department of Mechanical Engineering Institute of Internal Combustion Engines

OME Vorstellung. Introduction, Overview. Technical University of Munich Department of Mechanical Engineering Institute of Internal Combustion Engines OME Vorstellung Introduction, Overview Technical University of Munich Department of Mechanical Engineering Institute of Internal Combustion Engines Institute of Internal Combustion Engines Overview The

More information

VIRTUAL HYBRID ON THE ENGINE TEST BENCH SMART FRONTLOADING

VIRTUAL HYBRID ON THE ENGINE TEST BENCH SMART FRONTLOADING VIRTUAL HYBRID ON THE ENGINE TEST BENCH SMART FRONTLOADING RDE ENGINEERING [EIL] J. GERSTENBERG, DR. S. STERZING-OPPEL, C. FISCHER, B. SEIDEL, D. TRENKLE, M. OFF, DR. M. GLORA Overview RDE tool chain Virtual

More information

Predictive Control Strategies using Simulink

Predictive Control Strategies using Simulink Example slide Predictive Control Strategies using Simulink Kiran Ravindran, Ashwini Athreya, HEV-SW, EE/MBRDI March 2014 Project Overview 2 Predictive Control Strategies using Simulink Kiran Ravindran

More information

TURBOPROP ENGINE App. K AIAA AIRCRAFT ENGINE DESIGN

TURBOPROP ENGINE App. K AIAA AIRCRAFT ENGINE DESIGN CORSO DI LAUREA SPECIALISTICA IN Ingegneria Aerospaziale PROPULSIONE AEROSPAZIALE I TURBOPROP ENGINE App. K AIAA AIRCRAFT ENGINE DESIGN www.amazon.com LA DISPENSA E E DISPONIBILE SU http://www.ingindustriale.unisalento.it/didattica/

More information

Porsche Engineering driving technologies

Porsche Engineering driving technologies European GT-Suite User Conference 2016 Frankfurt am Main, 17. Oktober 2016 Real Drive Efficiency Improvement in turbocharged Engines by the use of Expansion Intake Manifold Content > Introduction Motivation

More information

Asian Marine Engineering Conference 2015 MAN Diesel & Turbo SE Turbocharger. Malte Oltmanns Promotion Manager October 2015

Asian Marine Engineering Conference 2015 MAN Diesel & Turbo SE Turbocharger. Malte Oltmanns Promotion Manager October 2015 Asian Marine Engineering Conference 2015 MAN Diesel & Turbo SE Turbocharger Malte Oltmanns Promotion Manager October 2015 MAN Diesel & Turbo Malte Oltmanns Asian Marine Engineering Conference 2015 / MDT

More information

Dipl.-Ing. Frank Pflüger. A new charging system for commercial diesel engines. Academy

Dipl.-Ing. Frank Pflüger. A new charging system for commercial diesel engines. Academy Dipl.-Ing. Frank Pflüger A new charging system for commercial diesel engines Academy Regulated Two-Stage Turbocharging - 3K-Warner's New Charging System for Commercial Diesel Engines Dipl.-Ing. Frank Pflüger,

More information

Engine Turbo/Super Charging. Super and Turbo-charging. Why super/ turbo-charging? Fuel burned per cycle in an IC engine is air limited

Engine Turbo/Super Charging. Super and Turbo-charging. Why super/ turbo-charging? Fuel burned per cycle in an IC engine is air limited Engine urbo/super Charging Super and urbo-charging Why super/ turbo-charging? Fuel burned per cycle in an IC engine is air limited (F/A) stoich = /4.6 orq m Q f, v fuel conversion and volumetric efficiencies

More information

Development of Two-stage Electric Turbocharging system for Automobiles

Development of Two-stage Electric Turbocharging system for Automobiles Development of Two-stage Electric Turbocharging system for Automobiles 71 BYEONGIL AN *1 NAOMICHI SHIBATA *2 HIROSHI SUZUKI *3 MOTOKI EBISU *1 Engine downsizing using supercharging is progressing to cope

More information

The Chances and Potentials for Low-Voltage Hybrid Solutions in Ultra-Light Vehicles

The Chances and Potentials for Low-Voltage Hybrid Solutions in Ultra-Light Vehicles Switzerland, Schlatt, 9 th -10 th October 2014 The Chances and Potentials for Low-Voltage Hybrid Solutions in Ultra-Light Vehicles Dipl.-Ing. Robert Steffan Prof. Dr. Peter Hofmann Prof. Dr. Bernhard Geringer

More information

Designing for Reliability and Robustness with MATLAB

Designing for Reliability and Robustness with MATLAB Designing for Reliability and Robustness with MATLAB Parameter Estimation and Tuning Sensitivity Analysis and Reliability Design of Experiments (DoE) and Calibration U. M. Sundar Senior Application Engineer

More information

THE FKFS 0D/1D-SIMULATION. Concepts studies, engineering services and consulting

THE FKFS 0D/1D-SIMULATION. Concepts studies, engineering services and consulting THE FKFS 0D/1D-SIMULATION Concepts studies, engineering services and consulting r e s e a r c h i n m o t i o n. VEHICLE IN MOTION On the basis of constant engine speeds and loads, the combustion engine

More information

Fuel Cell Application in a New Configured Aircraft PUBLISHABLE REPORT

Fuel Cell Application in a New Configured Aircraft PUBLISHABLE REPORT Fuel Cell Application in a New Configured Aircraft PUBLISHABLE REPORT Document Reference CELINA Publishable Report Contract Nr. AST4-CT-2005-516126 Version/Date Version 1.3 January 2009 Issued by Airbus

More information

Particle Sensor Performance & Durability for OBD Applications & Beyond

Particle Sensor Performance & Durability for OBD Applications & Beyond Particle Sensor Performance & Durability for OBD Applications & Beyond Imad Khalek & Vinay Premnath, SwRI June 30, 2015 19 th ETH Conference on Combustion Generated Nanoparticles, Zurich, Switzerland Southwest

More information

Objectives. WP7: On-engine aftertreatment systems. WP Leader: Jukka Leinonen. Partners:

Objectives. WP7: On-engine aftertreatment systems. WP Leader: Jukka Leinonen. Partners: WP7: On-engine aftertreatment systems Objectives Integration of SCR (Selective Catalytic Reduction) with the existing strong Miller cycle 4-stroke diesel engine and combining it with particulate emission

More information

Boosting System Challenges for Extreme Downsizing

Boosting System Challenges for Extreme Downsizing Department of Mechanical Engineering Powertrain & Vehicle Research Centre Boosting System Challenges for Extreme Downsizing 1 Thanks to contributors to this presentation UNIVERSITY OF BATH Andrew Lewis

More information

Behavior of a turbocharged gas engine during a low voltage ride through

Behavior of a turbocharged gas engine during a low voltage ride through Behavior of a turbocharged gas engine during a low voltage ride through Peter Schäffert, Josef Thalhauser, Herbert Schaumberger, Uwe Liebscher GE Jenbacher GmbH & Co OG Content Introduction Grid code Behavior

More information

SuperGen - Novel Low Cost Electro-Mechanical Mild Hybrid and Boosting System. Jason King, Chief Engineer

SuperGen - Novel Low Cost Electro-Mechanical Mild Hybrid and Boosting System. Jason King, Chief Engineer SuperGen - Novel Low Cost Electro-Mechanical Mild Hybrid and Boosting System Jason King, Chief Engineer FPC2015 Quick overview of Integral Powertrain (IPT) SuperGen concept Analysis results Test results

More information

Analysis of Sequential Turbocharger Systems for Diesel Engines Rob Stalman, Vanco Smiljanowski, Uwe Späder, Ford Research & Advanced Europe

Analysis of Sequential Turbocharger Systems for Diesel Engines Rob Stalman, Vanco Smiljanowski, Uwe Späder, Ford Research & Advanced Europe Analysis of Sequential Turbocharger Systems for Diesel Engines Rob Stalman, Vanco Smiljanowski, Uwe Späder, Ford Research & Advanced Europe October 24 th 2011, Ford Forschungszentrum Aachen GmbH, All rights

More information

Staged combustion concept for increased operational flexibility of gas turbines

Staged combustion concept for increased operational flexibility of gas turbines Staged combustion concept for increased operational flexibility of gas turbines Dieter Winkler, Antony Marrella, Janine Bochsler, Geoffrey Engelbrecht, Timothy Griffin, Peter Stuber Tagung Verbrennungsforschung,

More information

Design and Calculation of Fast-Running Shunting Locomotives

Design and Calculation of Fast-Running Shunting Locomotives Design and Calculation of Fast-Running Shunting Locomotives Dipl.-Ing. Claudia Kossmann Stadler Bussnang AG (Switzerland) SIMPACK User Meeting 2011 Shunting Locomotive Ee 922 - Introduction 2007: Swiss

More information

Simulation of the Mixture Preparation for an SI Engine using Multi-Component Fuels

Simulation of the Mixture Preparation for an SI Engine using Multi-Component Fuels ICE Workshop, STAR Global Conference 2012 March 19-21 2012, Amsterdam Simulation of the Mixture Preparation for an SI Engine using Multi-Component Fuels Michael Heiss, Thomas Lauer Content Introduction

More information

Studying Turbocharging Effects on Engine Performance and Emissions by Various Compression Ratios

Studying Turbocharging Effects on Engine Performance and Emissions by Various Compression Ratios American Journal of Energy and Power Engineering 2017; 4(6): 84-88 http://www.aascit.org/journal/ajepe ISSN: 2375-3897 Studying Turbocharging Effects on Engine Performance and Emissions by arious Compression

More information

The Generator-Electric Vehicle- A New Approach for Sustainable and Affordable Mobility

The Generator-Electric Vehicle- A New Approach for Sustainable and Affordable Mobility FORMForum 2016 1 The Generator-Electric Vehicle- A New Approach for Sustainable and Affordable Mobility M.Sc. Alexander Dautfest, Dipl.-Ing Christian Debes, Dipl.-Ing. Rüdiger Heim Fraunhofer Institute

More information

Engineering Success by Application of Star-CCM+ for Modern Gas Turbine Design

Engineering Success by Application of Star-CCM+ for Modern Gas Turbine Design March 18 th, 2014, Vienna, Austria STAR Global Conference Engineering Success by Application of Star-CCM+ for Modern Gas Turbine Design Karsten Kusterer B&B-AGEMA GmbH, Aachen, Germany Ryozo Tanaka Kawasaki

More information

Implementation of a Control Concept for the Car-in-the-Loop Test Rig on the IPG Xpack4 Real-Time Target

Implementation of a Control Concept for the Car-in-the-Loop Test Rig on the IPG Xpack4 Real-Time Target Implementation of a Control Concept for the Car-in-the-Loop Test Rig on the IPG Xpack4 Real-Time Target Kevin Engleson Control Concepts for the Car-in-the-Loop Test Rig Institut für Mechatronische Systeme

More information

"Power-to-X": Fuel quality - Potential of P2X-Fischer-Tropsch products in aviation

Power-to-X: Fuel quality - Potential of P2X-Fischer-Tropsch products in aviation "Power-to-X": Fuel quality - Potential of P2X-Fischer-Tropsch products in aviation 9 th International Freiberg Conference Session 7: Power-to-X Dr. Sophie Jürgens DLR Institute of Combustion Technology

More information

Velocity Optimization of Pure Electric Vehicles with Traffic Dynamics Consideration

Velocity Optimization of Pure Electric Vehicles with Traffic Dynamics Consideration Velocity Optimization of Pure Electric Vehicles with Traffic Dynamics Consideration Liuwang Kang, Haiying Shen, and Ankur Sarker Department of Computer Science, University of Virginia Outline Introduction

More information

German Weisser WÄRTSILÄ SWITZERLAND LTD. 3rd Technical Meeting 2013/14 of The Greek Section of The Society of Naval Architects and Marine Engineers

German Weisser WÄRTSILÄ SWITZERLAND LTD. 3rd Technical Meeting 2013/14 of The Greek Section of The Society of Naval Architects and Marine Engineers German Weisser WÄRTSILÄ SWITZERLAND LTD Current Trends in the Development of Large Two-Stroke Marine Diesel Engines in the Light of Significantly Changing Market Requirements and Environmental Regulations

More information

Modeling the Effect on Engine Performance of Heat Transfer and Friction losses in the Turbocharger

Modeling the Effect on Engine Performance of Heat Transfer and Friction losses in the Turbocharger Modeling the Effect on Engine Performance of Heat Transfer and Friction losses in the Turbocharger H. Tartoussi, A. Lefebvre, S. Guilain, Renault, A. J. Torregrosa, J. R. Serrano, F. Arnau, CMT 1 INTRODUCTION

More information

TDG-F-113 CEC New Test Development Proposal for a New Engine Fuels Test Procedure

TDG-F-113 CEC New Test Development Proposal for a New Engine Fuels Test Procedure TDG-F-113 CEC New Test Development Proposal for a New Engine Fuels Test Procedure DISI (Direct Injection spark ignited engine) Injector fouling Test 1. Demonstrated need- The proposed test will address

More information

SIMULATION AND EVALUATION OF ENGINE FRICTION EUROPEAN GT CONFERENCE, FRANKFURT/MAIN, OCTOBER 9TH, 2017

SIMULATION AND EVALUATION OF ENGINE FRICTION EUROPEAN GT CONFERENCE, FRANKFURT/MAIN, OCTOBER 9TH, 2017 SIMULATION AND EVALUATION OF ENGINE FRICTION EUROPEAN GT CONFERENCE, FRANKFURT/MAIN, OCTOBER 9TH, 2017 Prof. Dr.-Ing. Peter Steinberg, BTU Cottbus M.Sc. Oleg Krecker, PhD candidate, BMW AGENDA 1 2 3 4

More information

Dave Bone. DREAM Project Coordinator

Dave Bone. DREAM Project Coordinator Validation of radical engine architecture systems the alternative solution for a cleaner future Dave Bone Rolls-Royce plc Dave Bone Rolls-Royce plc DREAM Project Coordinator DREAM Project Coordinator This

More information

Hot Gas Stand durability tests for Turbine Housing design validation

Hot Gas Stand durability tests for Turbine Housing design validation Hot Gas Stand durability tests for Turbine Housing design validation SyTec M2A 2015 13 th October 2015 A. Loret - Turbo Engineering 2015 MITSUBISHI TURBOCHARGER AND ENGINE EUROPE BV All Rights Reserved.

More information

Optimising Aeristech FETT (Fully Electric Turbocharger Technology) for Future Gasoline Engine Requirements

Optimising Aeristech FETT (Fully Electric Turbocharger Technology) for Future Gasoline Engine Requirements Optimising Aeristech FETT (Fully Electric Turbocharger Technology) for Future Gasoline Engine Requirements Dr Sam Akehurst, Dr Nic Zhang 25 th April 2017 1 Contents Introduction to the Fully Electric Turbocharging

More information

WELCOME to the FLOX-COAL II Workshop

WELCOME to the FLOX-COAL II Workshop Institute of Combustion and Power Plant Technology Prof. Dr. techn. G. Scheffknecht WELCOME to the FLOX-COAL II Workshop Institute of Combustion and Power Plant Technology Prof. Dr. techn. G. Scheffknecht

More information

Part Load Engine Performance prediction for a gasoline engine using Neural Networks. Sreekanth R, Sundar S, Rangarajan S, Anand G -System Simulation

Part Load Engine Performance prediction for a gasoline engine using Neural Networks. Sreekanth R, Sundar S, Rangarajan S, Anand G -System Simulation Part Load Engine Performance prediction for a gasoline engine using Neural Networks Sreekanth R, Sundar S, Rangarajan S, Anand G -System Simulation CAE-2 System Simulation GT-SUITE User Conference Feb

More information

CONCEPTUAL CAR DESIGN AT BMW WITH FOCUS ON NVH PERFORMANCE

CONCEPTUAL CAR DESIGN AT BMW WITH FOCUS ON NVH PERFORMANCE CONCEPTUAL CAR DESIGN AT BMW WITH FOCUS ON NVH PERFORMANCE Dr. Manfred Kroiss (IABG) Dr. Luc Cremers (BMW Group) Dipl.-Ing. Vasilis Evangelou (BETA CAE Systems SA) 5th ANSA & µeta International Conference

More information

1-D Cycle Simulation. exemplified as a helpful Tool within the Scope of Truck Engine Development

1-D Cycle Simulation. exemplified as a helpful Tool within the Scope of Truck Engine Development 1-D Cycle Simulation exemplified as a helpful Tool within the Scope of Truck Engine Development Overview 1D Cycle Simulation exemplified as a helpful Tool within the Scope of Truck Engine Development 4General

More information

PHEV Control Strategy Optimization Using MATLAB Distributed Computing: From Pattern to Tuning

PHEV Control Strategy Optimization Using MATLAB Distributed Computing: From Pattern to Tuning PHEV Control Strategy Optimization Using MATLAB Distributed Computing: From Pattern to Tuning MathWorks Automotive Conference 3 June, 2008 S. Pagerit, D. Karbowski, S. Bittner, A. Rousseau, P. Sharer Argonne

More information

RHOMBUS BRIQUETTING MECHANISM MODELLING

RHOMBUS BRIQUETTING MECHANISM MODELLING RHOMBUS BRIQUETTING MECHANISM MODELLING Edgars Repsa, Eriks Kronbergs Institute of Mechanics, Faculty of Engineering, Latvia University of Agriculture edgars.repsa@llu.lv, eriks.kronbergs@llu.lv Abstract.

More information

Objectives / Expected Results

Objectives / Expected Results Objectives / Expected Results WP Leader: Dr. M. Moser, T. Moeller Cut operating, maintenance and deployment costs Develop systems, methods an processes for improved engine lifetime performance Reduction

More information

Crankcase scavenging.

Crankcase scavenging. Software for engine simulation and optimization www.diesel-rk.bmstu.ru The full cycle thermodynamic engine simulation software DIESEL-RK is designed for simulating and optimizing working processes of two-

More information

PIEZO ELECTRIC CONTROL HYDRAULIC STACKS FOR THE CAMLESS ENGINE

PIEZO ELECTRIC CONTROL HYDRAULIC STACKS FOR THE CAMLESS ENGINE PIEZO ELECTRIC CONTROL HYDRAULIC STACKS FOR THE CAMLESS ENGINE PROJECT REFERENCE NO. : 37S0751 COLLEGE : BASAVAKALYAN ENGINEERING COLLEGE, BIDAR BRANCH : MECHANICAL ENGINEERING GUIDE : SANTOSH PATIL STUDENTS

More information

Determination of the integration and influencing potential of rapid-charging systems for electric vehicles in distribution grids

Determination of the integration and influencing potential of rapid-charging systems for electric vehicles in distribution grids Foto: Martin Braun Determination of the integration and influencing potential of rapid-charging systems for electric vehicles in distribution grids Marcel Kurth, M.Sc. 4356 2241 6138 2821 7497 3819 10401

More information

EU Projekt HySYS Fuel Cell Hybrid Vehicle System Component Development

EU Projekt HySYS Fuel Cell Hybrid Vehicle System Component Development EU Projekt HySYS Fuel Cell Hybrid Vehicle System Component Development Dr. Jörg Wind, Daimler AG ECPE - HOPE Symposium Automotive Power Electronics 7-8 October 2008, Sindelfingen FC Hybrid Vehicle System

More information

Turbostroje 2015 Návrh spojení vysokotlaké a nízkotlaké turbíny. Turbomachinery 2015, Design of HP and LP turbine connection

Turbostroje 2015 Návrh spojení vysokotlaké a nízkotlaké turbíny. Turbomachinery 2015, Design of HP and LP turbine connection Turbostroje 2015 Turbostroje 2015 Návrh spojení vysokotlaké a nízkotlaké turbíny Turbomachinery 2015, Design of HP and LP turbine connection J. Hrabovský 1, J. Klíma 2, V. Prokop 3, M. Komárek 4 Abstract:

More information

NEWAC Overall Specification, Assessment and Concept Optimization

NEWAC Overall Specification, Assessment and Concept Optimization NEWAC Overall Specification, Assessment and Concept Optimization Andrew Rolt, Rolls-Royce plc. with contributions from: Konstantinos Kyprianidis, Cranfield University; Stefan Donnerhack and Wolfgang Sturm,

More information

DESTA - Demonstration of 1 st European SOFC Truck APU Jürgen Rechberger AVL List GmbH

DESTA - Demonstration of 1 st European SOFC Truck APU Jürgen Rechberger AVL List GmbH DESTA - Demonstration of 1 st European SOFC Truck APU 278899 Jürgen Rechberger AVL List GmbH Project and Partnership General Overview Demonstration of 1st European SOFC Truck APU 36 months Total Budget:

More information

SIP-adus Workshop A Traffic-based Method for Safety Impact Assessment of Road Vehicle Automation. Tokyo, 14 th November 2018

SIP-adus Workshop A Traffic-based Method for Safety Impact Assessment of Road Vehicle Automation. Tokyo, 14 th November 2018 SIP-adus Workshop 2018 A Traffic-based Method for Safety Impact Assessment of Road Vehicle Automation Tokyo, 14 th November 2018 Dr.-Ing. Adrian Zlocki, Christian Rösener, M.Sc., Univ.-Prof. Dr.-Ing. Lutz

More information

Green Mobility Technology Roadmap

Green Mobility Technology Roadmap Green Mobility Technology Roadmap Prof. Dr.-Ing. Horst E. Friedrich Institute of Vehicle Concepts German Aerospace Center (DLR) SCCER-Mobility 1st Annual Conference at ETH Zürich 11 th September 2014 www.dlr.de

More information

Performance Enhancement of Multi-Cylinder Common Rail Diesel Engine for Automotive Application

Performance Enhancement of Multi-Cylinder Common Rail Diesel Engine for Automotive Application Performance Enhancement of Multi-Cylinder Common Rail Diesel Engine for Automotive Application SUNDHARAM K, PG student, Department of Mechanical Engineering, Internal Combustion Engineering Divisions,

More information

Bicycle Hardware in the Loop Simulator for Braking Dynamics Assistance System

Bicycle Hardware in the Loop Simulator for Braking Dynamics Assistance System Bicycle Hardware in the Loop Simulator for Braking Dynamics Assistance System IPG Apply & Innovate 2016 Conference Session: Off Highway Cornelius Bott, Martin Pfeiffer, Oliver Maier, Jürgen Wrede 21.09.2016

More information

THERMAL ANALYSIS OF PISTON BLOCK USING FINITE ELEMENT ANALYSIS

THERMAL ANALYSIS OF PISTON BLOCK USING FINITE ELEMENT ANALYSIS THERMAL ANALYSIS OF PISTON BLOCK USING FINITE ELEMENT ANALYSIS Pushpandra Kumar Patel 1, Vikky Kumhar 2 1 BE Student, 2 Assistant Professor Department of Mechanical Engineering, SSTC-SSGI, Junwani, Bhilai,

More information

HYBRID-PROCEDURES AND CHALLENGES FOR EMISSION MEASUREMENT SYSTEMS

HYBRID-PROCEDURES AND CHALLENGES FOR EMISSION MEASUREMENT SYSTEMS HYBRID-PROCEDURES AND CHALLENGES FOR EMISSION MEASUREMENT SYSTEMS K. Engeljehringer AVL List GmbH, Graz, Austria Prof. Dr. C. Beidl Technische Universität Darmstadt Dr. B. Lenzen Technische Universität

More information

Simulation of Collective Load Data for Integrated Design and Testing of Vehicle Transmissions. Andreas Schmidt, Audi AG, May 22, 2014

Simulation of Collective Load Data for Integrated Design and Testing of Vehicle Transmissions. Andreas Schmidt, Audi AG, May 22, 2014 Simulation of Collective Load Data for Integrated Design and Testing of Vehicle Transmissions Andreas Schmidt, Audi AG, May 22, 2014 Content Introduction Usage of collective load data in the development

More information

USING OF dspace DS1103 FOR ELECTRIC VEHICLE MODELING

USING OF dspace DS1103 FOR ELECTRIC VEHICLE MODELING USING OF dspace DS1103 FOR ELECTRIC VEHICLE MODELING T. Haubert, T. Hlinovsky, P. Mindl Czech Technical University in Prague, Faculty of El. Engineering, Dept. of El. Drives and Traction Abstract This

More information