HIGH-PERFORMANCE LIGHTING EQUIPMENT BASED ON LIGHT-EMITTING DIODE

Transcription

1 HIGH-PERFORMANCE LIGHTING EQUIPMENT BASED ON LIGHT-EMITTING DIODE

2 The UE TETRAEDR offers up-to-date energy and recourse saving products based on semiconductor light sources and developed by TETRAEDR. Every Customer is offered world standard products adapted to the Customer s local environment (electric power consumption, lighting specifications and design) in compliance with the Customer s requirements. White LEDs made at our own plants as well as produced by the leading world manufacturers are employed in our products as light sources. LEDS of any color gamma may be offered at the Customer s request. Solar modular may be used to power LEDs. LEDs main advantages: At the average LED power consumption is 5-10 times less than that of an incandescent lamp; besides the LED service life is times longer than the service life of incandescent lamps. LED modular design and the lack of moving mechanical parts enable them to work in harsh vibration-related environment and decrease significantly operating costs (repair costs and service costs). The LED may emit practically any illumination color. LED efficiency factor is substantially higher than that of the incandescent lamp with the same color filter due to its emission in the narrow spectral band. The LED requires low voltage power. Therefore their application enables us to make a lighting device safe for customers. The lack of detrimental to health substances. The LEDs are resistant to multiple on-off cycles as against the incandescent lamps. The LED response time to change in voltage is measured in nanoseconds. It is essentially less than the incandescent lamp response time. It enables LED to work in the pulsed mode without fails for a long time which makes LED convenient for employment in signaling devices and in stage lighting instruments. Ultraviolet and infrared constituents are not present in the illumination spectrum. Therefore colors of paintings do not fade away and do not become colorless. The illuminated surface does not get warm. These features are useful not only in the museums but also in medicine (complex surgical operations). Colors may be changed dynamically without using additional filters.

3 PRODUCT RANGE OF COMMERCIALLY MANUFACTURED LED DEVICES STREET LIGHTS LED-based street lights are designed to illuminate streets, highways, neighborhood territories, parks, residential and industrial areas. Pendants or lamp posts (6-12 m- high) are optimal variants for installation of LED street lights. The operating temperature range is from -40 o С up to +45 o С. STREET LIGHT IL-DL-L02-180W Cd/klm C0-C180 C90-C270 = 31% The newly-developed modular design has a large area of heat radiators to dissipate heat efficiently. Every module meets the requirements for the IP67 degree of protection. Modules may be assembled and dismantled separately if required. The frame of the Street Light is made of aluminum alloy with protective coating and its absolute cross-section ensures thermal conditions for LEDs. The removable upper cover provides easy access to the device. Installation mode console Mounting hole diameter 60 mm. The Street Light may be equipped with the solar cell power system. Cold white color (Т= К) is available to order. Protection degree Lifetime 730 x 400 x 120 mm, 11 kg IP65 220V АC hours

4 STREET LIGHT DL-L01-180W LEDs are mounted on the aluminum board to ensure maximum heat dissipation and transfer. The frame of the Street Light is made of aluminum alloy with protective coating and its absolute cross-section ensures thermal conditions for LEDs. The following color shades are available to order: cold white Т= К neutral white Т= К warm white Т=3000К Protection degree consumption Light specifications vertical horizontal 530 x 384 x 116 mm 12 kg IP65 220V АC 120 Watt Parameters Designation Value mode unit Luminous flux 220V F 8500 lm Maximum luminous intensity 220V l max 4500 cd Half intensity beam angle 220V 2 0,5 I max 80х110 degrees Maximum illuminance (9m) 220V Е 40 lx Ratio I max /F 220V I max /F 550 cd/kilolumen Lifetime 220V T hours

5 Luminous intensity, cd. TUNNEL LIGHTS The Tunnel Light is designed to illuminate streets, highways, tunnels, store premises, hangars, parks and other infrastructure objects of residential and industrial areas. Pendants or lamp posts (6-12 m-high) are optimal variants for installation of LED street lights. The operating temperature range is from -40 o С up to +45 o С. LEDs are mounted on the aluminum boards to ensure maximum heat dissipation and transfer. The frame of the Street Light is made of aluminum alloy with protective coating and its absolute cross-section ensures thermal conditions for Radiation pattern 5000 LEDs. The following colors are offered to order: 4000 cold white Т= К 3000 neutral white Т= К 2000 warm white Т=3000К TUNNEL LIGHT CL-KS5-180W Angular distribution of radiation luminous Intensity, I v I max cd I ax cd cd Horizontal plant Vertikal plant 220 I max Iv deg 0.5Iv deg Iv deg 0.1Iv deg Vertical plant Horisontal plant All models have identical design Protection degree consumption Light specifications 850 x 305 x 120 mm 11 kg IP65 220V АC 180 W Parameters mode Designation Value unit Luminous flux 220V F lm Maximum luminous intensity 220V l max 4605 cd Half intensity beam angle 220V 2 0,5 I max 113x100 degrees Maximum illuminance (14m) 220V Е 25 lx I max /F 220V I max /F 384 cd/klm Lifetime 220V T h

6 Luminous intensity, cd TUNNEL LIGHT CL-KS4-120W Angular distribution of radiation luminous Intensity, I v I max cd I ax cd cd Horizontal plant Vertikal plant 220 I max Iv deg 0.5Iv deg Iv deg 0.1Iv deg Vertical plant Horisontal plant All models have identical design. Protection degree consumption 730 x 305 x 120 mm 8 kg IP65 220V АC 120 W Light specifications Parameters Designation Value mode unit Luminous flux 220V F 8000 lm Maximum luminous intensity 220V l max 2943 cd Half intensity beam angle 220V 2 0,5 I max 117x104 degrees Maximum illuminance (9m) 220V Е 34 lx I max /F 220V I max /F 368 cd/klm Lifetime 220V T h

7 TUNNEL LIGHT IL-DS-CD-C01072 vertical horizontal Protection degree consumption 560 x 310 x 150 mm 8 kg IP65 220V АC 60 W Light specifications Parameters Designation Value mode unit Luminous flux 220V F 5100 lm Maximum l;uminous intensity 220V l max 4600 cd Half intensity beam angle 220V 2 0,5 I max 60x75 degrees Maximum illuminance (9m) 220V Е 50 lx I max /F 220V I max /F 900 cd/klm Lifetime 220V T h

8 HOUSING AND COMMUNAL SERVICES LIGHT LED Lights featuring electric power form 24 to 250 W for housing and communal services and general lighting. The Light is designed to illuminate underground crossings, entrances, stairway enclosures, elevators (lifts), passages, back offices. It also may be used in transport means and industry. Vertical and horizontal surfaces (height m) are optimal variants for installation of this Light. LEDs are mounted on the aluminum board to ensure maximum heat dissipation and transfer. Light specifications vertical horizontal Parameters Designation Value mode unit Luminous flux 30V F 400 lm Maximum luminous intensity 30V l max 180 cd Half intensity beam angle 30V 2 0,5 I max 100х100 degrees Maximum illuminance (3m) 30V Е 20 lx I max /F 30V I max /F 440 cd/klm Lifetime 30V T h

9 LED LIGHTS, INDICATORS AND SIGNALING DEVICES FOR RAIL WAY TRANSPORT AND UNDERGROUND (SUBWAY) HEAD LIGHT LPB-01 It does not have analogues in the world Produced using 100% domestic hardware components Superpower Head Light based on LEDs vertical horizonta The Head Light is designed to illuminate railway lines in front of the train at nights. White LEDS with a special optical system using Fresnel lens are the source of lighting. LEDs are mounted on the aluminum board to ensure maximum heat dissipation and transfer. The frame of the Street Light is made of aluminum alloy with protective coating and its absolute cross-section ensures thermal conditions for LEDs. The Head Light is designed for operation in cold temperature environment (М25 ГОСТ ). Permissible mechanical impact (М25 ГОСТ ). The beam may be adjusted ± 5 horizontally and vertically. The setting dimensions and port sizes of the Head Light allow its application in locomotives instead of the currently employed head lights.

10 External exposure protection degree (ГОСТ IP 63) Current consumption Light specification Axial luminous intensity: BRIGHT mode DIM mode 470 х 150 х 380 mm 18 kg trai embedded network 50V and 110V DC 350 W ±10% cd ±20% cd The beam dispersion angle in the horizontal and vertical planes is 2Ө/2 = 3 5 (half intensity beam angle).

11 SOLAR MODULE SOLAR MODULE TO POWER LED LIGHTS Module MSW - 170/85(24) type Electric parameters Front surface Back surface ±5% (W) Current at maximum power Imp (А) Voltage at maximum powervmp (V) 34 Nominal voltage (V) 24 Short-circuit current Isc (А) Open-circuit voltage Voc (V) Dimension: Length (mm) 1575 Height (mm) 807 Width (mm) 46 Solar cell type (mm) [ps pseudosquare] p/s 125 mm Solar cell elements number (arrangement) 72 (6х12) (kg) 18 Guarantee: 1 year fort manufacturing defects. Performance deterioration no more than by 20% during 20 years of service life LED devices main advantages Efficiency Energy saving Energy efficiency Longevity Ecological compatibility Electrical safety Vibration resistance Speed performance (nanoseconds) Brightness level control (0% - 100%) Usability Maintainability Light flux directed Operating life