Installation STUD JOIST A237R SPECIFICATIONS. Width Height Depth Weight Max. Spacing between Mounts Max. Load

Transcription

1 WILREP LTD SPECIAL CONSTRUCTION 14 manufactured sound & vibration control components Installation A237R SPECIFICATIONS Width Height Depth Weight Max. Spacing between Mounts Max. Load FURRING CHANNEL SPECIFICATIONS Minimum Depth Width at Top Width at Bottom is a registered Trademark of Studco Corp inch inch inch Lbs. 48 inch. O.C. 36 Lbs. 25 Gauge with hemmed edge 7/8 inch or 1.5 inch inch inch. STUD JOIST 1-5/8 Resilmount A237R Isolation Clip 3 APPROVED FASTENERS (for all applications). 7/8 (A) Wood: # 8 x 2-1/2 Coarse Threads (B) Steel: # 8, # 10 or # 12 x 1-5/8 Self Tapping Type S (C) Concrete: 3/16 inch. x 2-1/4 Anchor Screws 1.25 DO NOT fasten Resilmount clips to framing members with nails. Use only approved screws. 7/8 (A) 2 1/ MAX. (B) (C) 1-5/8 2-1/4 Washer Supplied When splicing hat channels, overlap 6 inches in between two Resilmount Clips. Secure the channel with two 7/16 framing scews or 18 Gauge wire can be used. 1 AcoustiGuard WILREP LTD Matheson Blvd. East, Unit C-10, Mississauga, Ontario L4W 2P5 Tel.:(905) Toll Free: info@wilrep.com Website:

2 Load Specification Resilmount A237R Clips are designed to carry furring channel with one or more layers of gypsum wallboard attached. The load capacity of the clips depends on the gauge of the hat channel used. 25 Gauge channel is most commonly used and performs better acoustically than a heavier gauge channel.the maximum design load capacity for the Resilmount Clips in shear (Wall Application) or in tension (Ceiling Applications) as follows. Design load calculations are based on testing loading to failure where the furring channel deforms. Align furring channel with Resilmount Clips Maximum Load Wall & Ceiling Resilmount Clips w/ 25 gauge hat channel Resilmount Clips w/ 22 gauge hat channel 2:1 Safety factor 45 Lbs. 60 Lbs. 2.5:1 Safety factor 36 Lbs. 48 Lbs. Suggested safety factor of 2.5:1 for more critical life safety applications. Note: 5/8 thick gypsum drywall weighs 2.3 Lbs. / sq.ft. 1/2 thick gypsum drywall weighs 1.85 Lbs. / sq.ft. Fire Rated Applications Insert bottom hemmed edge into Clip Read Resilmount Installation instructions carefully before installing the clips. Resilmount A237R clips are supplied with a 1/4 x 1 steel washer. VERY IMPORTANT: On Fire Rated Applications the Resilmount washer must be used as shown. If this washer is not installed the clip has NO Fire Rating. Squeeze track and insert top edge Use approved fasteners for wood, steel and concrete. Do not fasten Resilmount clips with nails. On steel truss and C-stud applications, the screws are replaced with a 1/4 x 1-1/2 bolt with nylox nut. 2

3 Wall Installation Guide INSTALLATION NOTES Resilmount A237R shall not exceed 48" on center. Spacing between hat channels shall not exceed 24". Fasten the Resilmount A237R to the substrate with a fastener approved for a minimum pull-out and shear of 120 Lbs. Hat Channels are installed perpendicular to the studs. Locate the bottom row of Resilmount clips within 4" of the floor and the top row within 4 of the ceiling. Use sample calc. formula on Pg. 5 to determine the on center spacing between all of the tracks. A laser pointer or snap chalk line can be used to ensure that the Resilmount Clips and furring channels are installed horizontal and level. Install the drywall vertically from the bottom up leaving a 1/8" to 1/4 thick gap around perimeter of wall to be filled with acoustical caulk. Caulk around the entire perimeter of the gypsum board. Step 1 Review layout guidelines and check measurements before starting the installation. It is recommended that the ceiling is installed after the walls are in place. Step 2 Space Resilmount A237R so not to exceed 48" O.C. along line of furring channel. Secure clips with a single fastner through the washer and the middle screw hole in the clip. Step 3 Snap hat channels onto the Resilmount clips. Step 4 Place 1/4 shims on the floor in front of the sole plate. The shims are crititcal to ensure that the drywall does not touch the floor once attached to the tracks on the Resilmount clips. Use approved screws to attach the drywall to the channels following local building codes. Note: Only remove the shims after all the gypsum board is completely installed. Step 5 Use acoustical caulk around the entire perimeter of each wall. 3

4 Ceiling Installation Guide INSTALLATION NOTES Resilmount A237R shall not exceed 48" on center. Spacing between hat channels shall not exceed 16. Fasten the Resilmount A237R to the substrate with a fastener approved for a minimum pull-out and shear of 120 Lbs. Hat Channels are installed perpendicular to the joists. Locate the first row of Resilmount clips within 4 inches a wall and within 4 inches of the opposite wall use sample calc. formular on Pg. 5 to determine the on center spacing between all of the tracks. Use a laser pointer or snap chalk line to ensure the channels are accurately spaced. Install the gypsum board leaving 1/8 to 1/4" wide gap around perimeter to be filled with acoustical caulk. Caulk around the entire perimeter of the gypsum board. Step 1 Review layout guidelines and check measurements before starting the installation of walls or ceilings. It is recommended that the walls are in place before the ceiling is installed. Step 2 Space Resilmount A237R so not to exceed 48" OC. along the line of the furring channel. Secure clips with a single fastener through the washer and middle screw hole in the clip. Step 3 Snap hat channel onto the Resilmount clips. Step 4 Use approved screws to attach the drywall to the channels following local building codes. Step 5 Use acoustical caulk around the entire perimeter of each wall. 4

5 Installation Guide WALL STUD 9 x 16 Wall Sample Layout 16 MAXIMUM Track Spacing for WALLS 24" O.C. Actual 20" O.C. for this sample layout 9 STUDS Resilmount A237R Clips on 7/8 Furring Channel CALC. FOR SPACING OF HAT TRACKS* 108" - 4" (top) - 4" (bottom) = " 24" = 4.166" 5 spaces 5 spaces = 6 hat tracks 100" 5 = 20" apart O.C. * Also called Furring Channel max. 48 clip spacing 16 O.C. CEILING JOIST 9 x 16 Ceiling Sample Layout 16 MAXIMUM Track Spacing for CEILINGS 16" O.C. Actual 14-1/4" O.C. for this sample layout 9 JOISTS Resilmount A237R Clips on 7/8 Furring Channel CALC. FOR SPACING OF HAT TRACKS* 108" - 4" (wall side) - 4" (opposite wall side) = " 16" = 6.25" 7 spaces 7 spaces = 8 hat tracks 100" 7 = ¼" apart O.C. * Also called Furring Channel max. 48 clip spacing 16 O.C. 5

6 LENGTHHEIGH Clip Usage Guide For WALLS Resilmount A237R Usage Chart Metal Furring Channel at 24" O.C. with Resilmount at 48" O.C. Field Conditions May Effect Quantity Required T39-41' ' ' 5-8' 9-12' 13-16' 17-20' 21-24' 25-28' 29-32' 33-36' 37-40' 41-44' 45-48' 49-52' 53-56' 57-60' 61-64' 1-3' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' Note: Add 4 Resilmount Clips at each drywall butt joint condition for optimum acoustical UL Fire resistive assembly compliance. See UL Fire Resistive Design Specifications. 6

7 Clip Usage Guide For CEILINGS Resilmount A237R Usage Chart Metal Furring Channel at max. 16" O.C. with Resilmount at 48" O.C. Field Conditions May Effect Quantity Required LENGTHWIDTH ' ' ' 5-8' 9-12' 13-16' 17-20' 21-24' 25-28' 29-32' 33-36' 37-40' 41-44' 45-48' 49-52' 53-56' 57-60' 61-64' 1-1.3' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' ' Note: Add 4 Resilmount Clips at each drywall butt joint condition for optimum acoustical UL Fire resistive assembly compliance. See UL Fire Resistive Design Specifications. 7

8 HEIGHTLENGT Ceilings - Track and Joist Orientation WHEN THE TRACKS RUN LONGER THAN THE JOISTS; Use the chart on Pg. 7 as shown WIDTH AXIS on the user chart for the width of the ceiling and the LENGTH AXIS for the length of the ceiling. LENGTHHEIGHTNote: JOISTS TRACKS Note: WHEN THE JOISTS RUN LONGER THAN THE TRACKS; Use the LENGTH AXIS on the User Chart for the width of the ceiling and the WIDTH AXIS on the User Chart for the length of the ceiling. JOISTS HTRACKS Issue Date: September 12, Check online for the most up to date copy. This document is subject to change without notice. Resilmount is registered Trademark of Studco Building Systems