Table of Contents. Ara Brace Technical Notes... 74

Transcription

1

2 Table of Contents Redefining Linear Lighting... 2 Sample Applications Clean Room... 4 Classroom... 8 Offi ce Conference Room Lab Corridor/Hall Lynk Series (Defi ned by optic) Surface Mount/Suspended Lynk Linear Fluorescent Lynk Linear LED Styk Linear LED Tryg Linear LED Beam Linear Fluorescent Beam Linear LED Wall Beam Linear Fluorescent Beam Linear LED Lynk Linear Fluorescent Lynk Linear LED Styk Linear LED Tryg Linear LED Exterior Suspended Styk Linear LED Tryg Linear LED Exterior Wall Styk Linear LED Tryg Linear LED Application Shots of Pendants/Wall Sconces Pendants Curvus Lyra Pavo Pictor Wall Ara Bow Curvus Indus Lyra Pictor Tryg Exterior Wall Tryg Ara Brace Technical Notes... 74

3 linear lighting you can do more with STILE. flexibility in the field Rotate in 30 increments from 0 all the way to 360. adjustability to fit Infinitely adjustable in the field. HVAC system in the way? No problem. Slide the mounting point over. personalizing to target Create a bulkhead specific for your project to add a personal touch. 2

4 add color to the bulkhead to add interest (ABF option) interrupted runs for placement Only place fixtures where light is needed, an interrupted run allows precise fixture placement. elevations are easy The system can easily follow the elevation of stairs, up or down. circular runs to match The linear system can follow curves or bends in the space, creating a perfect blend. 3

5 clean room PROJECT GOAL Provide an energy-efficient lighting solution that meets IES-recommended light levels for medium bench or machine work. ROOM DETAILS Room Dimensions: 23' x 74' x 14' Reflectance Values: 65/50/20 Fixtures: 10' AFF 14' LIGHT LEVELS 50fc at work plane ENERGY CODE ASHRAE 90.1 (2007) Lighting Power Density (LPD) 1.2 Watt/square foot 23' 74' OUR SOLUTIONS EASILY QUALIFY F LEED* Layout Catalog Number Lighting Power Density (LPD) Maintained Foot Candles Additional LEED Points A LYNK SFSP I2 F28 L8 56' Watts/ft 2 57fc Yes - 25% below recommended LPD B LYNK SFSB I1 F54 L8 56' 0.95 Watts/ft 2 59fc Yes - 20% below recommended LPD C LYNK SFPT I2 F54 L4-6' 64' 0.95 Watts/ft 2 48fc Yes - 20% below recommended LPD D LYNK SFFT V4 F54 L4-6' 64' 0.96 Watts/ft 2 48fc Yes - 20% below recommended LPD E LYNK SFSB V2 F28 L8-3' 63' Watts/ft 2 60fc Yes - 35% below recommended LPD *Calculations done to current LEED 2009 standards. LEED 2009 references ASHRAE standards. LYNK SFSP I2 F28 L8 (2) 56' runs with seven 2-lamp 8' fi xtures. This layout uses a solid top lens with a perforated bottom shield. Great for use with dark ceilings, and maintaining a glare free environment. 4

6 LYNK SFSB I1 F54 L8 (2) 56' runs with seven 1-lamp 8' fi xtures. This layout uses a solid top lens. Great for use with dark ceilings. LYNK SFPP I2 F54 L4 BK01 (2) 64' interrupted runs with seven 2-lamp 4' fi xtures. The fi xtures are mounted on 10-foot centers. This layout uses a perforated top and bottom shield. 5

7 clean room PROJECT GOAL Provide an energy-efficient lighting solution that meets IES-recommended light levels for medium bench or machine work. ROOM DETAILS Room Dimensions: 23' x 74' x 14' Reflectance Values: 65/50/20 Fixtures: 10' AFF 14' LIGHT LEVELS 50fc at work plane ENERGY CODE ASHRAE 90.1 (2007) Lighting Power Density (LPD) 1.2 Watt/square foot 23' 74' OUR SOLUTIONS EASILY QUALIFY F LEED* Layout Catalog Number Lighting Power Density (LPD) Maintained Foot Candles Additional LEED Points A LYNK SFSP I2 F28 L8 56' Watts/ft 2 57fc Yes - 25% below recommended LPD B LYNK SFSB I1 F28 L8 56' 0.95 Watts/ft 2 59fc Yes - 20% below recommended LPD C LYNK SFPT I2 F54 L4-6' 64' 0.95 Watts/ft 2 48fc Yes - 20% below recommended LPD D LYNK SFFT V4 F54 L4-6' 64' 0.96 Watts/ft 2 48fc Yes - 20% below recommended LPD E LYNK SFSB V2 F28 L8-3' 63' Watts/ft 2 60fc Yes - 35% below recommended LPD *Calculations done to current LEED 2009 standards. LEED 2009 references ASHRAE standards. 64' LYNK SFFT V4 F54 L ' 10' (1) 64' run with seven 4-lamp 4' fi xtures on 10' centers. Using our forward throw refl ector we are able to use only one run, cutting installation labor in half

8 63' 11.5' 11' LYNK SFSB V2 F28 BK01 (2) 63' interrupted runs with six 2-lamp 8' fi xtures. The fi xtures are mounted on 11-foot centers. This layout uses a solid top lens

9 classroom PROJECT GOAL Provide an energy-efficient lighting solution that meets IES-recommended light levels for Classroom/Lecture/Training. ROOM DETAILS Room Dimensions: 30' x 30' x 10' Reflectance Values: 80/50/20 Fixtures: 8' 9" AFF 10' LIGHT LEVELS 40fc (general reading) at work plane ENERGY CODE ASHRAE 90.1 (2007) Lighting Power Density (LPD) 1.4 Watt/square foot 30' 30' OUR SOLUTIONS EASILY QUALIFY F LEED* Layout Catalog Number Lighting Power Density (LPD) Maintained Foot Candles Additional LEED Points A LYNK SFPP I2 F28 L8 24' Watts/ft 2 44fc Yes - 41% below recommended LPD B LYNK SFPP I3 F28 L8 24' Watts/ft 2 16fc (up) Calculation with top lamp only Watts/ft 2 44fc (down) Yes - 41% below recommended LPD C LYNK SFPP I2 F54 L4-6' 24' Watts/ft 2 39fc Yes - 37% below recommended LPD *Calculations done to current LEED 2009 standards. LEED 2009 references ASHRAE standards. LYNK SFPP I2 F28 L8 (2) 24' runs with three 2-lamp 8' fi xtures per run. Shown with twolamp fi xture utilizing a perforated top and bottom shield. 8' 24' 14' 8

10 LYNK SFPP I3 F28 L8 (2) 24' runs with three 3-lamp 8' fi xtures showing best practices for a classroom layout. Two downlights and one up light. Wired so that you cannot have all three on at the same time ' 24' ' LYNK SFPP I2 F54 L4 BK01 (2) 24' interrupted runs with 2-lamp 4' fi xtures. The runs are made of three fi xtures with 6' extrusions between the fi xtures. A higher wattage lamp maintains desired light levels ' 24' ' 9

11 office PROJECT GOAL Provide an energy-efficient lighting solution for an open office space that meets IES-recommended light levels. ROOM DETAILS Room Dimensions: 37' x 133' x 12' Reflectance Values: 75/50/20 Fixtures: 10' AFF 12' LIGHT LEVELS 40fc (basic tasks) at work plane 133' ENERGY CODE ASHRAE 90.1 (2007) Lighting Power Density (LPD) 1.0 Watt/square foot 37' OUR SOLUTIONS EASILY QUALIFY F LEED* Layout Catalog Number Lighting Power Density (LPD) Maintained Foot Candles Additional LEED Points A LYNK SFPP W2 F28 L8 120' Watts/ft 2 37fc Yes - 32% below recommended LPD B LYNK SFSP X2 F54 L8-X 120' Watts/ft 2 43fc Yes - 13% below recommended LPD C LYNK SFPB Z2 F28 L8-X 120' Watts/ft 2 27fc 1 Yes - 59% below recommended LPD *Calculations done to current LEED 2009 standards. LEED 2009 references ASHRAE standards. 1 Provides 38fc of light for the cubicle workstations. 120' ' LYNK SFPP W2 F28 L8 BK01 8' (2) 120' runs with 15 2-lamp 8' fi xtures per run. Shown with traditional two-lamp fi xture utilizing a perforated top and bottom shield

12 120' LYNK SFSP X2 F54 L ' 8' (2) 120' runs with nine 2-lamp 8' fi xtures per run. Taking advantage of the interrupted runs the light fi xtures are located above each workstation, maximizing light where you want it LYNK SFPB Z2 F28 L8 (2) 120' runs with nine 2-lamp 8' fi xtures per run. This layout uses the same wattage lamp as layout A (28W). The placement of the lamps still provides 38fc for the workspace. 11

13 conference room PROJECT GOAL Provide an energy-efficient lighting solution that meets IES-recommended light levels for a conference room. ROOM DETAILS Room Dimensions: 12' x 32' x 10' Reflectance Values: 80/50/20 Fixtures: 8' AFF 10' LIGHT LEVELS 30fc at work plane ENERGY CODE ASHRAE 90.1 (2007) Lighting Power Density (LPD) 1.3 Watt/square foot 12' 32' OUR SOLUTIONS EASILY QUALIFY F LEED* Layout Catalog Number Lighting Power Density (LPD) Maintained Foot Candles Additional LEED Points A LYNK SFPP V2 F28 L4-1' 19' Watts/ft 2 30fc Yes - 44% below recommended LPD B LYNK SFPP I1 F54 L4-1' 19' Watts/ft 2 26fc Yes - 49% below recommended LPD C STYK SLCS 051 L58W 21' Watts/ft 2 19fc 1 Yes - 42% below recommended LPD *Calculations done to current LEED 2009 standards. LEED 2009 references ASHRAE standards. 1 Provides 35fc of light on the conference room table. LYNK SFPP V2 F28 L4 (1) 19' run with four 2-lamp 4' fi xtures per run. Shown with traditional twolamp fi xture utilizing a perforated top and bottom shield. 12

14 LYNK SFPP I1 F54 L4 (1) 19' run with four 1-lamp 4' fi xtures per run. One lamp 54W per fi xture achieves 0.656W/ft2. This is a 49% reduction, compared to ASHRAE allowable of 1.3W/ft2. 4' 3" 6' 21' STYK SLCS 051 L58W (1) 21' run with fi ve 051 modules STYK fi xtures have 35fc maintained on the conference table. Lit with LEDs, it easily meets current energy codes

15 lab PROJECT GOAL Provide an energy-efficient lighting solution that meets IES-recommended light levels for Classroom/Lecture/Training. ROOM DETAILS Room Dimensions: 30' x 50' x 14' Reflectance Values: 80/50/20 Fixtures: 11' AFF 14' LIGHT LEVELS 50fc (performance of a visual task of medium or small size) at work plane ENERGY CODE ASHRAE 90.1 (2007) Lighting Power Density (LPD) 1.4 Watt/square foot OUR SOLUTIONS EASILY QUALIFY F LEED* 30' 50' Layout Catalog Number Lighting Power Density (LPD) Maintained Foot Candles Additional LEED Points A LYNK SFPP I2 F28 L8 24' Watts/ft 2 50fc Yes - 36% below recommended LPD B LYNK SFPB C2 F28 L8 24' Watts/ft 2 62fc Yes - 36% below recommended LPD C LYNK SFSP W2 F28 L8 24' Watts/ft 2 55fc Yes - 36% below recommended LPD *Calculations done to current LEED 2009 standards. LEED 2009 references ASHRAE standards LYNK SFPP I2 F28 L8 (4) 24' runs with three 2-lamp 8' fi xtures per run. Shown with traditional two-lamp fi xture utilizing a perforated top and bottom shield ' 24' 13' 14

16 LYNK SFPB C2 F28 L8 (4) 24' runs with three 2-lamp 8' fi xtures per run. Shown with traditional two-lamp fi xture utilizing a perforated top shield. We removed the bottom perforated shield to help increase light levels to 62fc LYNK SFSP W2 F28 L8 BK01 (4) 24' runs with three 2-lamp 8' fi xtures per run. If you have a dark ceiling, a solid top lens will maximize light levels. Shown with a perforated bottom shield ' 24' 13' 15

17 corridor PROJECT GOAL Provide an energy-efficient lighting solution that meets IES-recommended light levels for hallways. ROOM DETAILS Room Dimensions: 10' x 50' x 10' Reflectance Values: 80/50/20 Fixtures: 8' 6" AFF LIGHT LEVELS 15fc at floor ENERGY CODE ASHRAE 90.1 (2007) Lighting Power Density (LPD).5 Watt/square foot 10' 10' 50' OUR SOLUTIONS EASILY QUALIFY F LEED* Layout Catalog Number Lighting Power Density (LPD) Maintained Foot Candles Additional LEED Points A LYNK SFBL I1 F28 L4-6' 44' Watts/ft 2 13fc Yes - 26% below recommended LPD B LYNK SFPB I1 F28 L4-6' 44' Watts/ft 2 11fc Yes - 26% below recommended LPD C STYK SLCS 051 L19W 47' Watts/ft 2 14fc Yes - 16% below recommended LPD *Calculations done to current LEED 2009 standards. LEED 2009 references ASHRAE standards. LYNK SFBL I1 F28 L4 BK01 (1) 44' interrupted run with fi ve 4' fi xtures on ten-foot centers. This is done with a bare lamp, to achieve high uniformity in the space. 16

18 LYNK SFPB I1 F28 L4 (1) 44' interrupted run with fi ve 4' fi xtures on ten-foot centers. This layout uses a perforated top shield to reduce the uplight component, in case you have a dark ceiling. STYK SLCS 051 L19W (1) 47' continuous run with fi xtures. LEDs can be used and can meet current energy codes. 17

19 Lynk Series Linear Fluorescent Optical Distribution SFPP Symmetric Perforated Perforated Shield Actual Size 25% Perforated Top and Bottom Shield 86.3% efficiency 33% open perforated top shield 40% open perforated bottom shield This shielding provides great uniformity Makes the space feel light and airy The optic can be rotated in the field in 30 increments 75% SFPB Symmetric Perforated Shield Actual Size 10% Perforated Top Shield 100%+ efficiency 33% open peforated top shield Increases efficiency to optimize performance 90% downlight helps increase light levels The optic can be rotated in the field in 30 increments 90% 18 Tel

20 SFPT Symmetric Perforated Shield - Low-Profile Actual Size 25% Perforated Top Shield 98.6% efficiency Low-profile 40% perforated top shield Low-profile shielding makes the shielding disappear Rotate the shield to reduce lamp image The optic can be rotated in the field in 30 increments 75% SFFT Asymmetric Reflector Actual Size Forward Throw High Performance Asymmetric Reflector 90.3% efficiency 22% open perforated Perforated uplight Asymmetric distribution increases the coverage The optic can be rotated in the field in 30 increments Tel contact@specstile.com 19

21 Lynk Series Linear Fluorescent Optical Distribution SFSP Symmetric Solid Perforated Shield Actual Size 0% 100% Solid Top Reflector and Perforated Bottom Shield 82.4% efficiency 40% open perforated bottom shield 100% downlight with a perforated shield to reduce lamp image Great for dark or high ceilings The optic can be rotated in the field in 30 increments SFSB Symmetric Solid Reflector Actual Size 0% 100% Solid Top Reflector 100%+ efficiency Great for dark ceilings 100% downlight Efficiency is great The optic can be rotated in the field in 30 increments 20 Tel contact@specstile.com

22 SFST Symmetric Solid Reflector - Low Profile Actual Size 0% 100% Solid Top Reflector 87.6% efficiency Low-profile version of the symmetric solid reflector Use the reflector to aim the light and fit your needs The optic can be rotated in the field in 30 increments SFBL Bare Lamp Actual Size 360 No Shielding 100%+ efficiency Lowest cost, highest efficiency Provides great uniformity Tel contact@specstile.com 21

23 Lynk Linear Fluorescent Suspended Integral Ballast Series SFPP SFPB SFPT SFFT SFSP SFSB SFST SFBL 25% Uplight, 75% Downlight 10% Uplight, 90% Downlight 25% Uplight, 75% Downlight Forward Throw 100% Downlight 100% Downlight 100% Downlight 360 of Light Bulkhead Shapes and Lamp Configurations SIX STANDARD SHAPES SHAPES C I V W X Z 1 LAMP 2 LAMP 3 LAMP 4 LAMP Module Run Sections L4-X' MC L4 (48") Fixture L4 L4-X' Extrusion X' L8 (96") These modules feature adjustable mounting centers. See page 2 for additional information. YY' The capability to create interrupted runs is a unique feature of Stile linear lighting solutions. This allows you to meet Energy Codes by delivering light only where it is necessary. Order by selecting the L4 fixture module then add the length of the extrusion in one foot increments up to six feet maximum. Field Adjustments 0 Rotation 0 and 180 Rotation 30 Rotation 22 Tel contact@specstile.com

24 SERIES SHAPE LAMPS LAMPING VOLTAGE CIRCUITS MODULE RUN MOUNTING SUSPENSION FINISH OPTIONS CONTROLS Sample model number: SFST C 4 F C L8 48' MCA 072 PT01 LV4 LES SERIES SHAPE NUMBER OF LAMPS LAMPING VOLTAGE NUMBER OF CIRCUITS MODULE LENGTH OF RUN MOUNTING SUSPENSION FINISH OPTIONS CONTROLS SFPP SFPB SFPT SFFT SFSP SFSB SFST SFBL C I V W X Z Code Definitions F28 F C 2C L4 L8 L4-X' YY' BUL MCA MCS CAA CAS PT_ BK01 ABF LV4 MBP SGN EMI 1 EMR F C090 C135 1 Not availabe in 3 or 4 lamp version with 28W lamping or with a dimming option. LES LHL LET LH3 LEF LE1 LE2 AMX AMS WS1 WSR WSO W LAMPING CIRCUITS (See page 75 for details.) OPTIONS CONTROLS F28 2 F28WT5/Mini Bipin 1C One Circuit BK01 Bulkhead with Accent Tubes LES Lutron EcoSystem Ballast WS1 Watt Stopper Daylight Sensor F54 2 F54WT5HO/Mini Bipin. 2C. Two Circuit ABF LV4 Alternate Bulkhead Finish White Louver LHL LET Lutron Hi-Lume Ballast Lutron Eco-10 Ballast WSR Watt Stopper Daylight Sensor Remote MOUNTING (See page 78 for details.) SUSPENSION MBP Metal Braided Cord LH3 Lutron Hi-Lume 3D WSO Watt Stopper Occupancy Sensor BUL Ceiling Coupler MCA 2" Mini Canopy and Aircraft Cable (with T-Bar Clip) MCS 2" Mini Canopy and Stem CAA 5" Canopy and Aircraft Cable CAS 5" Canopy and Stem " " ". FINISHES (See Finishes on page 79.) PT Painted. (Include Paint Number) SGN Sign Mounting Brackets EMI Emergency Ballast Integral EMR Emergency ballast Remote F Fusing C Corner C Corner LEF LE1 LE2 Lutron Sensor Feed Lutron Daylight Sensor Lutron Infrared Receiver Controller Remote AMX Advance Mark X AMS Advance Mark VII W Watt Stopper Occupant Controller Remote 2 T5 FL linear lamp(s) not included. Customize Your Layout Options Corner pieces can be added to make any of our linear runs fit your application. We offer 90 and 135 corner pieces as standard. The bends are made using 2" conduit, matching the diameter of the extrusion containing the ballast. Elevation changes also available. Contact factory for details. C090 18" C135 R12" 90 18" R12" 6" 135 BK01 Bulkhead with Accent Tubes ABF Alternate Bulkhead Finish (Shown with PT19) 6" Specifications: Extruded aluminum construction provides durable protection for internal components and is recyclable. Adjustable mounting centers ease the installation process by allowing the fixture to adjust for each building system and structure. L4 is adjustable 6" to 48" mounting centers standard. Standard thermoset polyester powder coat paint provides durable protection in a palette of color options. Custom colors available upon request. Integral electronic ballast utilizes the latest energy-saving technology to maintain consistent color temperature, CRI and lumen maintenance, while eliminating the need for remote mounting and simplifying installation. Asymmetric and multiple symmetric optics allow increased light control and distribute light into a space exactly where it is needed. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. EMI Emergency Ballast Integral LV4 White Louver SGN Sign Mounted Bracket Tel contact@specstile.com 23

25 Lynk Linear LED Suspended Integral Power Supply Lynk Linear LED Inspired by the drive to push the lighting design barrier, Lynk delivers modern components creating a base upon which unique lighting designs can develop. A modernized pendant defined by its unique bulkheads, Lynk is a great alternative to traditional linear lighting designs. Its flexible, modular design LED lampings have the ability to deliver light where needed. Colors and designs are easily customized to fit your design. SMA Bulkhead Shapes and Lamp Configurations THREE STANDARD SHAPES SHAPES C I V 1 LAMP SMB C1 V1 2 LAMP C2 I2 V2 3 LAMP C3 V3 4 LAMP C4 I4 FT Module Run Sections L4-X' MC L4 (48") Fixture L4 L4-X' Extrusion X' L8 (96") These modules feature adjustable mounting centers. See page 2 for additional information. YY' The capability to create interrupted runs is a unique feature of Stile linear lighting solutions. This allows you to meet Energy Codes by delivering light only where it is necessary. Order by selecting the L4 fixture module then add the length of the extrusion in one foot increments up to six feet maximum. Field Adjustments 0 Rotation 30 Rotation 30 and 0 Rotation 24 Tel contact@specstile.com

26 SERIES Sample model number: SLCL SHAPE LAMPS C 4 LED TEMPERATURE OPTICS VOLTAGE CIRCUITS MODULE RUN MOUNTING SUSPENSION FINISH OPTIONS CONTROLS L34W 35K SMA 120 1C L4 48' BUL 048 AN04 F DML SERIES SLCL SHAPE NUMBER OF LAMPS LED LED TEMP OPTICS VOLTAGE NUMBER OF CIRCUITS MODULE LENGTH OF RUN MOUNTING SUSPENSION FINISH OPTIONS CONTROLS C I V WHITE LED L19W 30K L34W 35K L48W 1 45K L58W 1 COL LED B34W 2 Blue G34W 2 Green R34W 2 Red A34W 2 Amber C72W 1,2 RGB SMA SMB FT 120V 277V 1C 2C L4 L8 L4-X' YY' BUL MCA MCS CAA CAS AN04 AN08 BK01 ABF MBP SGN F C090 C135 DML DMR SQR MXR 1 DMR, SQR and MXR not available in 3 and 4 lamp configuration. 2 Color LED not available with the FT optic. Code Definitions OPTICS SMA Symmetric 60 Beam Spread SMB Symmetric 30 Beam - 60 Spread FT Forward Throw. CIRCUITS (See Finishes on page 75.) 1C One Circuit 2C Two Circuit MOUNTING (See page 78 for details.) BUL Ceiling Coupler MCA 2" Mini Canopy and Aircraft Cable (with T-Bar Clip) MCS 2" Mini Canopy and Stem CAA 5" Canopy and Aircraft Cable CAS 5" Canopy and Stem SUSPENSION " " ". FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS BK01 Bulkhead with Accent Tubes ABF Alternate Bulkhead Finish MBP Metal Braided Cord SGN Sign Mounting Brackets F Fusing C Corner C Corner CONTROLS DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming Customize Your Layout We offer two standard corner pieces to be used with any run you are building. We offer 90 and 135 as a standard. Custom bends are available. The bends are made using a 3" tube. Elevation changes also available. Contact factory for details. Options C090 18" C135 R12" 90 18" R12" 6" 135 BK01 Bulkhead with Accent Tubes ABF Alternate Bulkhead Finish (Shown with PT18) 6" Specifications: Asymmetric and multiple symmetric optics allow increased light control that delivers light into a space exactly where it is needed. Can be locked in desired orientation for precise fixture alignment. Extruded aluminum construction provides durable protection for internal components and is recyclable. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. L70 life = 50,000 + hours. Patent Pending. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. Tel contact@specstile.com 25

27 Styk Linear LED Surface Mount/Suspended Remote Power Supply Styk Linear LED Styk was built to provide the most lumens with the smallest luminaire package, while optimizing life. Not limited to decorative lighting, effective functional lighting is provided through the optimal light control in this minimal package. Styk boasts three white LED color temperatures, RGB and four color offerings. Styk is a durable interior linear LED fixture. Styk s patent pending optical offerings enable tremendous flexibility offering wall washing, wall grazing, indirect pendants and asymmetric lighting solutions. SMA Run Sections and Suspension SLCS Bracket Mount 1.5" MC 3" SLCS Stem Mount SMB OAH MC 1.5" FT Mounting Dimensions MODULE MOUNTING CENTER (MC) " " " " " Mounting Options BRK 3" Bracket MCS 2" Mini Canopy and Stem CAS 5" Canopy and Stem 26 Tel contact@specstile.com

28 SERIES MODULE LED TEMPERATURE OPTICS VOLTAGE RUN MOUNTING SUSPENSION FINISH OPTIONS Sample model number: SLCS 051 L34W 35K SMA ' CAS 072 AN04 PS SERIES SLCS MODULE LED LED WHITE COL WHITE TEMP LED COL OPTICS VOLTAGE LENGTH OF RUN MOUNTING SUSPENSION FINISH OPTIONS L19W L34W L48W L58W L24W L42W L60W L72W 30K 35K 45K 30K 35K 45K B34W 1 G34W 1 R34W 1 A34W 1 C72W 1 B42W 1 G42W 1 R42W 1 A42W 1 C91W 1 Blue Green Red Amber RGB Blue Green Red Amber RGB SMA SMB FT 24V DC YY' BRK MCS CAS AN04 AN08 PS PSN PSE F DML DMR SQR MXR 077 L29W L50W L72W L86W 30K 35K 45K B50W 1 G50W 1 R50W 1 A50W 1 C109W 1 Blue Green Red Amber RGB 089 L34W L59W L84W L101W 30K 35K 45K B59W 1 G59W 1 R59W 1 A59W 1 C127W 1 Blue Green Red Amber RGB 101 L38W L67W L96W L115W 30K 35K 45K B67W 1 G67W 1 R67W 1 A67W 1 C145W 1 Blue Green Red Amber RGB 1 Color LED not available with the FT optic. Code Definitions OPTICS SMA Symmetric 60 Beam Spread SMB Symmetric 30 Beam - 60 Spread FT Forward Throw MOUNTING (See page 78 for details.) BRK 3" Bracket MCS 2" Mini Canopy and Stem CAS 5" Canopy and Stem SUSPENSION 003 3" (BRK Only) " " " FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS PS Power Supply PSN No Power Supply PSE Power Supply Enclosure F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming Specifications: Asymmetric and multiple symmetric optics allow increased light control and distribute light into a space exactly where it is needed. Extruded aluminum construction provides durable protection for internal components and is recyclable. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. L70 life = 50,000+ hours. Stem mount versions include (2) 5/8" aluminum stem(s) painted to match anodized finish. Patent Pending. Fixture requires connection to a 24V constant voltage power supply. Fixtures over 68W may require multiple power supplies/feeds. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. Tel contact@specstile.com 27

29 Tryg Linear LED Surface Mount/Suspended Remote Power Supply Tryg Linear LED Tryg, a low-profile LED fixture offers a unique design and durability suitable for any project. LEDs enable this luminaire to feature a low-profile housing, while its creative design acts as an efficient heat sink, maximizing output and life by allowing the LEDs to operate at an optimal temperature. 9% 91% MUSR Adjustable Mounting Points SLCT Fixed Mounting Points Run Sections MUSR/SLCT Fixed Bracket Mount MC 7.1" MUSR 3.5" 4.9" SLCT 2.1" 100% MUSR/SLCT Aircraft Cable Mount MC OAH MUSR SLCT Mounting Dimensions Mounting Options MODULE MOUNTING CENTER (MC) " FBK Fixed Bracket BUL.6" Ceiling Coupler CAA 5" Canopy and Aircraft Cable CAS 5" Canopy and Stem 28 Tel contact@specstile.com

30 SERIES MODULE LED TEMPERATURE VOLTAGE RUN MOUNTING SUSPENSION FINISH OPTIONS Sample model number: SLCT 048 L34W 35K ' CAS 072 AN04 PSN SERIES MODULE LED LED WHITE COL WHITE TEMP LED COL VOLTAGE LENGTH OF RUN MOUNTING SUSPENSION FINISH OPTIONS MUSR SLCT 048 L19W L34W L38W L48W L58W L67W L96W L115W 30K 35K 45K B34W G34W R34W A34W C72W B67W G67W R67W A67W Blue Green Red Amber RGB Blue Green Red Amber 24V DC YY' FBK BUL CAA CAS AN04 AN08 PS PSN PSE BK01 ABF F DML DMR SQR MXR Code Definitions MOUNTING (See page 78 for details.) FBK BUL CAA CAS Fixed Bracket.6" Ceiling Coupler 5" Canopy and Aircraft Cable 5" Canopy and Stem SUSPENSION 002 2" (FBK Only) " " " FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS PS Power Supply PSN No Power Supply PSE Power Supply Enclosure BK01 Bulkhead with Accent Tubes ABF Alternative Bulkhead Finish F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming ABF Alternate Bulkhead Finish (Shown with PT10) Specifications: Extruded aluminum construction provides durable protection for internal components and is recyclable. External fasteners are flush, providing a clean design. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. L70 = 50,000+ hours. Stem mount versions include (2) 5/8" aluminum stem(s) painted to match anodized finish. Fixture requires connection to a 24V constant voltage power supply. Fixtures over 68W may require multiple power supplies/feeds. Frosted acrylic shield enhances a space with diffused illumination. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. Tel contact@specstile.com 29

31 Tryg Linear LED Suspended Integral Power Supply MUSE SLCI Tryg Linear LED Tryg, a low-profile LED fixture offers a unique design and durability suitable for any project. LEDs enable this luminaire to feature a low-profile housing, while its creative design acts as an efficient heat sink, maximizing output and life by allowing the LEDs to operate at an optimal temperature. 9% 91% Bulkhead Shapes and Lamp Configurations FOUR STANDARD SHAPES SHAPES J K L M 100% 1 LAMP Run Sections MUSE/SLCI Canopy and Stem MUSE SLCI OAH 7.8" 5.9" MC 7.3" 4.9" Module 048-X' MC Fixture Extrusion 048 X' 048-X' These modules feature adjustable mounting centers. See page 2 for additional information. The capability to create interrupted runs is a unique feature of Stile linear lighting solutions. This allows you to meet Energy Codes by delivering light only where it is necessary. Order by selecting the L4 fixture module then add the length of the extrusion in one foot increments up to six feet maximum. YY' Mounting Dimensions MODULE MOUNTING CENTER (MC) " Mounting Options BUL.6" Ceiling Coupler CAA 5" Canopy and Aircraft Cable CAS 5" Canopy and Stem 30 Tel contact@specstile.com

32 SERIES SHAPE MODULE LED TEMPERATURE VOLTAGE RUN MOUNTING SUSPENSION FINISH OPTIONS Sample model number: SLCI J 048 L34W 35K ' CAS 072 AN04 F SERIES SHAPE MODULE LED LED WHITE COL WHITE TEMP LED COL VOLTAGE LENGTH OF RUN MOUNTING SUSPENSION FINISH OPTIONS MUSE SLCI J K L M X' L19W L34W L38W L48W L58W L67W L96W L115W 30K 35K 45K B34W G34W R34W A34W C72W B67W G67W R67W A67W Blue Green Red Amber RGB Blue Green Red Amber YY' BUL CAA CAS AN04 AN08 BK01 ABF F DML DMR SQR MXR Code Definitions MOUNTING (See page 78 for details.) BUL.6" Ceiling Coupler CAA 5" Canopy and Aircraft Cable CAS 5" Canopy and Stem SUSPENSION " " " FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS BK01 Bulkhead with Accent Tubes ABF Alternate Bulkhead Finish F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming ABF Alternate Bulkhead Finish (Shown with PT19) Specifications: Extruded aluminum construction provides durable protection for internal components and is recyclable. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. L70 = 50,000+ hours. Stem mount versions include (2) 5/8" aluminum stem(s) painted to match anodized finish. Optical grade diffuse acrylic lens optimizes performance. SPI Lighting uses strict guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. Tel contact@specstile.com 31

33 Beam Linear Fluorescent and LED Suspended/Wall Remote or Integral Ballast/Remote Power Supply Beam Linear Fluorescent and LED Beam delivers quality illumination in an award-winning fixture. It has the versatility to be mounted on the wall or ceiling. Its standard 18" projection can be shortened to meet ADA requirements and is offered with integral and remote ballast options. Beam s ETL damp location listing and multiple shielding options enable this low-profile fixture to adapt to many applications. Run Sections and Suspension SFCB/SLCB Interior Pendant Remote Ballast/Remote Power Supply Shielding Options APS OAH MC 1" SFWB/SLWB Interior Wall Remote Ballast/Remote Power Supply OAP 1" SPS MC SFWB/SLWB Interior Wall Integral Ballast/Remote Power Supply 1" OAP PLS MC Mounting Dimensions Mounting Options MODULE MOUNTING CENTER (MC) " " " " CAS 5" Canopy and Stem ICS 1.4" Canopy LBC 4" J-Box Cover TS SBC Switch-Box Cover SMT Surface Mount SJB Surface Mount w/ Standard J-Box Cover Fixture shown with 18" overall projection. 32 Tel contact@specstile.com

34 SERIES Sample model number: SFCB MODULE 041 SUSPENSION/ LAMPING VOLTAGE RUN MOUNTING PROJECTION FINISH OPTIONS 1F ' CAS 048 AN01 F Fluorescent SERIES MODULE LAMPING VOLTAGE LENGTH OF RUN MOUNTING SUSPENSION PROJECTION FINISH OPTIONS SFCB SFWB F14 1F24 1F21 1F39 1F28 1F54 1F YY CAS 2 SBC LBC ICS SMT SJB 2 For SFCB only PT_ AN01 TS PLS SPS APS EMI EMR F DM 1F DM not available LED SERIES MODULE LAMPING VOLTAGE LENGTH OF RUN MOUNTING SUSPENSION PROJECTION FINISH OPTIONS SLCB SLWB L10W L17W L14W L25W L19W L34W L24W L42W 24V DC YY' CAS 3 SBC LBC ICS SMT 4 SJB 4 3 For SLCB only. 4 Remote power supply PT_ AN01 PS PSN PSE TS PLS SPS APS F DML Code Definitions FLUESCENT LAMPING F14 5 F14WT5/Mini Bipin F24 5 F24WT5H0/Mini Bipin F21 5 F21WT5/Mini Bipin F39 5 F39WT5/Mini Bipin F28 5 F28WT5/Mini Bipin F54 5 F54WT5H0/Mini Bipin F35 5 F35WT5/Mini Bipin F80 5 F80WT5/Mini Bipin 5 T5 FL linear lamp(s) not included. MOUNTING (See page 78 for details.) CAS 5" Canopy and Stem ICS 1.4" Mini Canopy and Stem LBC 4" J-Box Cover SBC Switch-Box Cover SMT Surface Mount SJB Surface Mount with Standard J-Box Cover SUSPENSION " " " PROJECTION 004 4" ADA 006 6" " " FINISHES (See Finishes on page 79.) PT Painted Coat Finish AN01 Anodized Satin Aluminum OPTIONS PS Power Supply (LED Only) PSN No Power Supply (LED Only) PSE Power Supply Enclosure TS Translucent Shield PLS 7 Perforated Lamp Screen SPS 7 Symmetric Perforated Screen APS 7 Asymmetric Perforated Screen EMI 6 Emergency Ballast Integral EMR 6 Emergency Ballast Remote F Fusing DM Lutron ECO-10 DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming 6 For FL only. 7 Available in PT_ and AN01. Specifications: Standard thermoset polyester powder coat paint provides durable protection in a palette of color options. Custom colors available upon request. Field adjustable housing locks into position, enabling precise fixture alignment for high quality design performance. Fluorescent remote or integral electronic ballast utilizes the latest energy-saving technology to maintain consistent color temperature, CRI and lumen maintenance. LED fixtures requires connection to a 24V constant voltage power supply. LED comes with remote power supply. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. Tel contact@specstile.com 33

35 Lynk Linear Fluorescent Wall Integral or Remote Ballast Lynk Linear Fluorescent Inspired by the drive to push the lighting design barrier, Lynk delivers modern components creating a base upon which unique lighting designs can develop. Lynk is a great alternative to traditional linear lighting designs. Its flexible, modular design, has the ability to deliver light where it is needed. Colors and designs are easily customized to fit your design. Series SWPP SWPB SWPT SWFT SWSP SWSB SWST SWBL 25% Uplight, 75% Downlight 10% Uplight, 90% Downlight 25% Uplight, 75% Downlight Forward Throw 100% Downlight 100% Downlight 100% Downlight 360 of Light Bulkhead Projections Mounting Options TWO STANDARD SHAPES SHAPE I Integral Ballast I Remote Ballast SMT Surface Mount MBK 2" Mini Bracket LBK Bracket 1 LAMP Run Sections Module L4 (48") Surface Mount Integral Ballast 5" MC (48") 2.4" Mini Bracket Mount Remote Ballast OAP MC (48") 2" 34 Tel contact@specstile.com

36 SERIES SHAPE LAMPS LAMPING VOLTAGE CIRCUITS MODULE RUN MOUNTING PROJECTION FINISH OPTIONS CONTROLS Sample model number: SWPP I 1 F C L4 48' SMT 005 PT01 EMI AMX SERIES SHAPE NUMBER OF LAMPS LAMPING VOLTAGE NUMBER OF CIRCUITS MODULE LENGTH OF RUN MOUNTING PROJECTION FINISH OPTIONS CONTROLS SWPP I 1 F C L4 YY' SMT PT_ BK01 LES SWPB F MBK 006 ABF LHL SWPT LBK 012 LV4 LET SWFT 018 EMI 1 LH3 SWSP 1 Integral ballast only. EMR 2 LEF SWSB F LE1 SWST SWBL 1 Integral ballast only. 2 Remote ballast only. LE2 AMX AMS WS1 WSR WSO W Code Definitions LAMPING PROJECTION OPTIONS CONTROLS F28 3 F28WT5/Mini Bipin 005 5" Integral Ballast BK01 Bulkhead with Accent Tubes LES Lutron EcoSystem Ballast AMS Advance Mark VII F54 3 F54WT5H0/Mini Bipin 006 6" Remote Ballast ABF Alternate Bulkhead Finish LHL Lutron Hi-Lume Ballast WS1 Watt Stopper Daylight Sensor MOUNTING (See page 78 for details.) " Remote Ballast " Remote Ballast LV4 White Louver EMI 4 Emergency Ballast Integral LET LH3 Lutron Eco-10 Ballast Lutron Hi-Lume 3D WSR Watt Stopper Daylight Sensor Remote SMT Surface Mount MBK 2 Mini Bracket Mount. FINISHES (See Finishes on page 79.) EMR 5 Emergency Ballast Remote F Fusing LEF LE1 Lutron Sensor Feed Lutron Daylight Sensor WSO Watt Stopper OccupancySensor LBK Bracket 3 T5 FL linear lamp(s) not included. PT Painted. (Include Paint Number) 4 Integral ballast only. 5 Remote ballast only. LE2 Lutron Infrared Receiver Controller Remote W Watt Stopper Occupant Controller Remote AMX Advance Mark X Specifications: Options Aluminum construction provides durable protection for internal components and is recyclable. Rotates and locks in desired orientation for precise fixture alignment. Asymmetric and multiple symmetric optics allow increased light control and distribute light into a space exactly where it is needed. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. BK01 Bulkhead with Accent Tubes ABF Alternate Bulkhead Finish (Shown with PT32) Tel contact@specstile.com 35

37 Lynk Linear LED Wall Remote Power Supply Lynk Linear LED Inspired by the drive to push the lighting design barrier, Lynk delivers modern components creating a base upon which unique lighting designs can develop. A modernized fixture defined by its unique bulkheads, Lynk is a great alternative to traditional linear lighting designs. Its flexible, modular design LED lampings has the ability to deliver light where needed. Colors and designs are easily customized to fit your design. SMA Bulkhead Projections ONE STANDARD SHAPE SHAPE I Remote Power Supply MODULE SMB Run Sections Module 048 (48") Mini Bracket Mount Remote Power Supply OAP FT MC 2" Bracket Mount Remote Power Supply OAP 2" MC Mounting Dimensions MODULE MOUNTING CENTER (MC) " " " " " Mounting Options MBK 2" Mini Bracket LBK Bracket 36 Tel contact@specstile.com

38 SERIES MODULE LED TEMPERATURE OPTICS VOLTAGE RUN MOUNTING PROJECTION FINISH OPTIONS Sample model number: SLLS 048 L34W 35K SMA ' MBK 012 AN04 PS SERIES SLLS MODULE LED LED WHITE COL WHITE TEMP LED COL OPTICS VOLTAGE LENGTH OF RUN MOUNTING PROJECTION FINISH OPTIONS 048 L19W 30K B34W 1 Blue SMA 24V DC YY' MBK 003 L34W L48W 35K 45K L58W 060 L24W 30K L42W 35K L60W 45K L72W G34W 1 Green R34W 1 Red A34W 1 Amber C72W 1 RGB B42W 1 Blue G42W 1 Green R42W 1 Red A42W 1 Amber C91W 1 RGB SMB LBK 006 FT AN04 AN08 PS PSN PSE BK01 ABF F DML DMR SQR MXR 072 L29W L50W L72W L86W 30K 35K 45K B50W 1 Blue G50W 1 Green R50W 1 Red A50W 1 Amber C109W 1 RGB 084 L34W L59W L84W L101W 30K 35K 45K B59W 1 Blue G59W 1 Green R59W 1 Red A59W 1 Amber C127W 1 RGB 096 L38W L67W L96W L115W 30K 35K 45K B67W 1 Blue G67W 1 Green R67W 1 Red A67W 1 Amber C145W 1 RGB 1 Color LED not available with FT optic. Code Definitions OPTICS SMA Symmetric 60 Beam Spread SMB Symmetric 30 Beam - 60 Spread FT Forward Throw MOUNTING (See page 78 for details.) MBK 2" Mini Bracket Mount LBK Bracket PROJECTION 006 6" " " FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS PS Power Supply PSN No Power Supply PSE Power Supply Enclosure BK01 Bulkhead with Accent Tubes ABF Alternate Bulkhead Finish F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming Specifications: Aluminum construction provides durable protection for internal components and is recyclable. Rotates and locks in desired orientation for precise fixture alignment. Asymmetric and multiple symmetric optics allow increased light control and distribute light into a space exactly where it is needed. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. Patent Pending. LED fixtures requires connection to a 24V constant voltage power supply. Fixtures over 68W may require multiple power supplies/feeds. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. Tel contact@specstile.com 37

39 Styk Linear LED Wall Remote or Integral Power Supply Styk Linear LED Styk was built to provide the most lumens with the smallest luminaire package, while still optimizing lamp output and life. Not limited to decorative lighting, effective functional lighting is provided through optimal light control in this minimal package. Styk boasts three white LED color temperatures, RGB and four color offerings. Styk is a durable interior linear LED fixture. Styk s patent pending optical offerings enable tremendous flexibility offering wall washing, wall grazing, indirect pendants and asymmetric lighting solutions. SMA Run Sections and Suspension SLWS Bracket Mount BRK 3" LBK LBI 1.5" MC SMB SLWS Horizontal Stem Mount MCS 1.6" 2" MC FT Mounting Dimensions MODULE MOUNTING CENTER (MC) " " " " " Mounting Options BRK 3" Bracket Mount MCS 2" Mini Canopy and Stem LBK Bracket LBI Bracket w/integral Power Supply SBC Switch-Box Cover and Stem COV Cove Mount Two Adjustable Mounting Brackets (standard) 38 Tel contact@specstile.com

40 SERIES MODULE LED TEMPERATURE OPTICS VOLTAGE RUN MOUNTING PROJECTION FINISH OPTIONS Sample model number: SLWS 051 L34W 35K SMA ' MCS 012 AN04 PS SERIES SLWS MODULE LED LED WHITE COL WHITE TEMP LED COL OPTICS VOLTAGE LENGTH OF RUN MOUNTING PROJECTION FINISH OPTIONS L19W L34W L48W L58W L24W 30K 35K 45K 30K B34W 12 G34W 12 R34W 12 A34W 12 C72W 12 B42W 2 Blue Green Red Amber RGB Blue SMA SMB FT 24V DC YY' BRK MCS SBC LBK LBI 3 COV BRK only V. L42W 35K G42W 2 Green L60W 45K R42W 2 Red L72W 1 A42W 2 Amber C90W 2 RGB AN04 AN08 PS PSN PSE F DML DMR SQR MXR 077 L29W L50W L72W 1 L86W 1 30K 35K 45K B50W 2 Blue G50W 2 Green R50W 2 Red A50W 2 Amber C108W 2 RGB 089 L34W L59W L84W 1 L101W 1 30K 35K 45K B59W 2 Blue G59W 2 Green R59W 2 Red A59W 2 Amber C126W 2 RGB 101 L38W 30K L67W 35K L96W 1 45K L115W 1 1 Not available with LBI B67W 2 Blue G67W 2 Green R67W 2 Red A67W 2 Amber C144W 2 RGB 2 Color LED not available with FT optic. Code Definitions OPTICS SMA Symmetric 60 Beam Spread SMB Symmetric 30 Beam - 60 Spread FT Forward Throw MOUNTING (See page 78 for details.) BRK 3" Bracket Mount MCS 2" Mini Canopy and Stem SBC Switch-Box Cover LBK Bracket LBI Bracket w/integral Power Supply COV Cove Mount PROJECTION 003 3" (BRK Only) 006 6" " " FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS PS Power Supply PSN No Power Supply PSE Power Supply Enclosure F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming Specifications: Extruded aluminum construction provides durable protection for internal components and is recyclable. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. L70 life = 50,000+ hours. Stem mount versions include (2) 5/8" aluminum stem(s) painted to match anodized finish. LED optical grade acrylic lens optimizes performance. Patent Pending. Remote fixture requires connection to a 24V constant voltage power supply. Fixtures over 68W may require multiple power supplies/feeds. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. Tel contact@specstile.com 39

41 Tryg Linear LED Wall Remote Power Supply MUWR SLWT Tryg Linear LED Tryg, a low-profile LED fixture offers a unique design and durability suitable for any project. LEDs enable this luminaire to feature a low-profile housing, while its creative design acts as an efficient heat sink, maximizing output and life by allowing the LEDs to operate at an optimal temperature. Run Sections MUWR Fixed Bracket mount 7.1" MC 3.5" SLWT Fixed Bracket mount 4.9" MC 2.1" Mounting Dimensions MODULE MOUNTING CENTER (MC) " " " Mounting Options FBK Fixed Bracket FBK Fixed Bracket 40 Tel contact@specstile.com

42 SERIES Sample model number: SLWT MODULE 048 LED TEMPERATURE VOLTAGE RUN MOUNTING FINISH OPTIONS L34W 35K ' FBK AN04 PSN SERIES MODULE LED LED WHITE COL WHITE TEMP LED COL VOLTAGE LENGTH OF RUN MOUNTING FINISH OPTIONS MUWR SLWT L19W L34W L38W L48W L58W L67W L96W L115W L38W L67W L77W L96W L115W L134W L192W L230W 30K 35K 45K 30K 35K 45K B34W G34W R34W A34W C72W B67W G67W R67W A67W B67W G67W R67W A67W C145W B134W G134W R134W A134W Blue Green Red Amber RGB Blue Green Red Amber Blue Green Red Amber RGB Blue Green Red Amber 24V DC YY' FBK AN04 AN08 PS PSN PSE BK01 ABF F DML DMR SQR MXR 144 L58W L101W L115W L144W L172W L202W L288W L346W 30K 35K 45K B101W G101W R101W A101W C217W B202W G202W R202W A202W Blue Green Red Amber RGB Blue Green Red Amber Code Definitions MOUNTING (See page 78 for details.) FBK Fixed Bracket FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS PS Power Supply PSN No Power Supply PSE Power Supply Enclosure BK01 Bulkhead with Accent Tubes ABF Alternate Bulkhead Finish F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming BK01 Bulkhead with Accent Tubes ABF Alternate Bulkhead Finish (Shown with PT15) Specifications: Extruded aluminum construction provides durable protection for internal components and is recyclable. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. L70 = 50,000+ hours. LED optical grade acrylic lens optimizes performance. Fixture requires connection to a 24V constant voltage power supply. Fixtures over 68W may require multiple power supplies/feeds. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. Tel contact@specstile.com 41

43 Styk Exterior Linear LED Surface Mount/Suspended Remote Power Supply Styk Exterior Linear LED Styk was built to provide the most lumens with the smallest luminaire package, while still optimizing lamp output and life. Not limited to decorative lighting, effective functional lighting is provided through optimal light control in this minimal package. Styk boasts three white LED color temperatures, RGB and four color offerings. Styk is a durable interior linear LED fixture. Styk s patent pending optical offerings enable tremendous flexibility offering wall washing, wall grazing, indirect pendants and asymmetric lighting solutions. SMA Run Sections and Suspension SECS Bracket Mount 1.5" MC 3" SECS Stem Mount SMB OAH MC 1.5" FT Mounting Dimensions MODULE MOUNTING CENTER (MC) " " " " " Mounting Options BRK 3" Bracket MCS 2" Mini Canopy and Stem CWS 6.2" Canopy and Stem 42 Tel contact@specstile.com

44 SERIES MODULE LED TEMPERATURE OPTICS VOLTAGE RUN MOUNTING SUSPENSION FINISH OPTIONS Sample model number: SECS 051 L34W 35K SMA ' MCS 072 AN04 PS SERIES SECS MODULE LED LED WHITE COL WHITE TEMP LED COL OPTICS VOLTAGE LENGTH OF RUN MOUNTING SUSPENSION FINISH OPTIONS L19W L34W L48W L58W L24W L42W L60W L72W 30K 35K 45K 30K 35K 45K B34W 1 G34W 1 R34W 1 A34W 1 C72W 1 B42W 1 G42W 1 R42W 1 A42W 1 C91W 1 Blue Green Red Amber RGB Blue Green Red Amber RGB SMA SMB FT 24V DC YY' BRK MCS CWS BRK only. AN04 AN08 PS PSN PSE F DML DMR SQR MXR 077 L29W L50W L72W L86W 30K 35K 45K B50W 1 Blue G50W 1 Green R50W 1 Red A50W 1 Amber C109W 1 RGB 089 L34W L59W L84W L101W 30K 35K 45K B59W 1 Blue G59W 1 Green R59W 1 Red A59W 1 Amber C127W 1 RGB 101 L38W L67W L96W L115W 30K 35K 45K B67W 1 Blue G67W 1 Green R67W 1 Red A67W 1 Amber C145W 1 RGB 1 Color LED not available with FT optic. Code Definitions OPTICS SMA Symmetric 60 Beam Spread SMB Symmetric 30 Beam - 60 Spread FT Forward Throw MOUNTING (See page 78 for details.) BRK 3" Bracket MCS 2" Mini Canopy and Stem CWS 6.2" Canopy and Stem SUSPENSION 003 3" (BRK Only) " " " FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS PS Power Supply PSN No Power Supply PSE Power Supply Enclosure F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming Specifications: IP66 rated fixture per International Electrotechnical Commission (IEC) certifies fixture as dust tight and protected against powerful water jets. External fasteners are flush stainless steel, providing a clean design. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. L70 life = 50,000+ hours. Stem mount versions include (2) 5/8" aluminum stem(s) painted to match anodized finish. LED optical grade acrylic lens optimizes performance. Fixture requires connection to a 24V constant voltage power supply. Fixtures over 68W may require multiple power supplies/feeds. Patent Pending. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C ). ETL listed to UL standards (US and Canada) for ground mounting and use in wet locations. Tel contact@specstile.com 43

45 Tryg Exterior Linear LED Surface Mount/Suspended Remote Power Supply Tryg Exterior Linear LED Tryg, a low-profile LED fixture offers a unique design and durability suitable for any project. LEDs enable this luminaire to feature a low-profile housing, while its creative design acts as an efficient heat sink, maximizing output and life by allowing the LEDs to operate at an optimal temperature. Run Sections SECT Fixed Bracket Mount MC 1.9" SECT Stem Mount OAH MC Mounting Dimensions MODULE MOUNTING CENTER (MC) " Mounting Options FBK Fixed Bracket CWS 6.2" Canopy and Stem 44 Tel contact@specstile.com

46 SERIES Sample model number: SECT MODULE 050 LED TEMPERATURE VOLTAGE RUN MOUNTING SUSPENSION FINISH OPTIONS L34W 35K ' FBK 072 AN04 PSN SERIES SECT MODULE LED LED WHITE COL WHITE TEMP LED COL VOLTAGE LENGTH OF RUN MOUNTING SUSPENSION FINISH OPTIONS 050 L19W L34W L38W L48W L58W L67W L96W 1 L115W 1 30K 35K 45K B34W G34W R34W A34W C72W B67W G67W R67W A67W Blue Green Red Amber RGB Blue Green Red Amber 24V DC YY' FBK CWS AN04 AN08 PS PSN PSE CA01 F DML DMR SQR MXR 1 Not available with FBK mount. Code Definitions MOUNTING (See page 78 for details.) FBK Fixed Bracket CWS 6.2" Canopy and Stem SUSPENSION 002 2" (FBK Only) " " " FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS PS Power Supply PSN No Power Supply PSE Power Supply Enclosure CA01 Color Accent F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming CA01 Color Accent (Shown with PT33) Specifications: IP66 rated fixture per International Electrotechnical Commission (IEC) certifies fixture as dust-tight and protected against powerful water jets. Extruded aluminum construction provides durable protection for internal components and is recyclable. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. L70 life = 50,000+ hours. Stem mount versions include (2) 5/8" aluminum stem(s) painted to match anodized finish. LED optical grade acrylic lens optimizes performance. Fixture requires connection to a 24V constant voltage power supply. Fixtures over 68W may require multiple power supplies/feeds. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for ground mounting and use in wet locations. Tel contact@specstile.com 45

47 Styk Exterior Linear LED Wall Remote or Integral Power Supply Styk Exterior Linear LED Styk was built to provide the most lumens with the smallest luminaire package, while still optimizing lamp output and life. Not limited to decorative lighting, effective functional lighting is provided through optimal light control in this minimal package. Styk boasts three white LED color temperatures, RGB and four color offerings. Styk is a durable interior linear LED fixture. Styk s patent pending optical offerings enable tremendous flexibility offering wall washing, wall grazing, indirect pendants and asymmetric lighting solutions. SMA Run Sections and Suspension SEWS Bracket Mount BRK 3" LBK LBI 1.5" MC SMB SEWS Horizontal Stem Mount MCS 1.6" 2" MC FT Mounting Dimensions MODULE MOUNTING CENTER (MC) " " " " " Mounting Options BRK 3" Bracket Mount MCS 2" Mini Canopy and Stem LBK Bracket LBI Bracket w/integral Power Supply SBC Switch-Box Cover and Stem COV Cove Mount Two Adjustable Mounting Brackets (standard) 46 Tel contact@specstile.com

48 SERIES MODULE LED TEMPERATURE OPTICS VOLTAGE RUN MOUNTING PROJECTION FINISH OPTIONS Sample model number: SEWS 051 L34W 35K SMA ' MCS 012 AN04 F SERIES SEWS MODULE LED LED WHITE COL WHITE TEMP LED COL OPTICS VOLTAGE LENGTH OF RUN MOUNTING PROJECTION FINISH OPTIONS L19W L34W L48W L58W L24W L42W L60W L72W 1 30K 35K 45K 30K 35K 45K B34W 2 Blue G34W 2 Green R34W 2 Red A34W 2 Amber C72W 1,2 RGB B42W 2 Blue G42W 2 Green R42W 2 Red A42W 2 Amber C91W 1,2 RGB SMA SMB FT 24V DC YY' BRK 003 MCS 006 SBC 012 LBK 018 LBI 3 COV 3 Wet listed, but does not include IP66. AN04 AN08 PS PSN PSE F DML DMR SQR MXR 077 L29W L50W L72W 1 L86W 1 30K 35K 45K B50W 2 Blue G50W 2 Green R50W 2 Red A50W 2 Amber C108W 1,2 RGB 089 L34W L59W L84W 1 L101W 1 30K 35K 45K B59W 2 Blue G59W 2 Green R59W 2 Red A59W 2 Amber C127W 1,2 RGB 101 L38W 30K L67W 35K L96W 1 45K L115W 1 1 Not available with LBI. B67W 2 Blue G67W 2 Green R67W 2 Red A67W 2 Amber C145W 1,2 RGB 2 Color LED not available with FT optic. Code Definitions OPTICS SMA Symmetric 60 Beam Spread SMB Symmetric 30 Beam - 60 Spread FT Forward Throw MOUNTING (See page 78 for details.) BRK 3" Bracket MCS 2" Mini Canopy and Stem SBC Switch-Box Cover LBK Bracket LBI Bracket w/ Integral Power Supply PROJECTION 003 3" (BRK Only) 006 6" " " FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS PS Power Supply PSN No Power Supply PSE Power Supply Enclosure F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming COV Cove Mount Specifications: IP66 rated fixture per International Electrotechnical Commission (IEC) certifies fixture as dust-tight and protected against powerful water jets. Extruded aluminum construction provides durable protection for internal components and is recyclable. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. L70 life = 50,000+ hours. Stem mount versions include (2) 5/8" aluminum stem(s) painted to match anodized finish. LED optical grade acrylic lens optimizes performance. Fixture requires connection to a 24V constant voltage power supply. Fixtures over 68W may require multiple power supplies/feeds. Patent Pending. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for ground mounting and use in wet locations. Tel contact@specstile.com 47

49 Tryg Exterior Linear LED Wall Remote Power Supply Tryg Exterior Linear LED Tryg, a low-profile LED fixture offers a unique design and durability suitable for any project. LEDs enable this luminaire to feature a low-profile housing, while its creative design acts as an efficient heat sink, maximizing output and life by allowing the LEDs to operate at an optimal temperature. Run Sections SEWT Fixed Bracket Mount MC 5.0" 1.9" Mounting Dimensions MODULE MOUNTING CENTER (MC) " " " Mounting Options FBK Fixed Bracket 48 Tel contact@specstile.com

50 SERIES Sample model number: SEWT MODULE 050 LED TEMPERATURE VOLTAGE RUN MOUNTING FINISH OPTIONS L34W 35K ' FBK AN04 F SERIES SEWT MODULE LED LED WHITE COL WHITE TEMP LED COL VOLTAGE LENGTH OF RUN MOUNTING FINISH OPTIONS L19W 30K B34W Blue 24V DC YY' FBK AN04 L34W 35K G34W Green AN08 L38W 45K R34W Red L48W A34W Amber L58W B67W Blue L67W G67W Green L96W R67W Red L115W A67W Amber C72W RGB PS PSN PSE CA01 F DML DMR SQR MXR 098 L38W L67W L77W L96W L115W L134W L192W L230W 30K 35K 45K B67W G67W R67W A67W C145W B134W G134W R134W A134W Blue Green Red Amber RGB Blue Green Red Amber 146 L58W L101W L115W L144W L172W L202W L288W L346W 30K 35K 45K B101W G101W R101W A101W C217W B202W G202W R202W A202W Blue Green Red Amber RGB Blue Green Red Amber 2 Color LED not available with FT optic. Code Definitions MOUNTING FBK Fixed Bracket FINISHES (See Finishes on page 79.) AN04 Anodized Aluminum (clear) AN08 Black Anodized OPTIONS PS Power Supply PSN No Power Supply PSE Power Supply Enclosure CA01 Color Accent F Fusing DML 0-10V Dimming DMR RGB 0-10V Dimming SQR RGB Sequencer MXR RGB DMX Dimming CA01 Color Accent (Shown with PT33) Specifications: IP66 rated fixture per International Electrotechnical Commission (IEC) certifies fixture as dust-tight and protected against powerful water jets. Extruded aluminum construction provides durable protection for internal components and is recyclable. Available in anodized finishes with some parts painted to match. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. LED optical grade acrylic lens optimizes performance. Fixture requires connection to a 24V constant voltage power supply. Fixtures over 68W may require multiple power supplies/feeds. CA01 available to specify a Color Accent for the narrow band between end cap and extrusion. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LED s we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for ground mounting and use in wet locations. Tel contact@specstile.com 49

51 custom design ARA Interior/Exterior Wall Integral Power Supply Pages 63, 71 50

52 BOW Interior Wall Remote Ballast/Remote Power Supply Pages 64, 65 51

53 BRACE Exterior Wall Remote Ballast/ Integral Ballast Pages 72, 73 52

54 custom design CURVUS Interior Pendant/Interior Wall Integral Ballast Pages 59, 66 53

55 INDUS Interior Wall Integral Ballast/Integral Power Supply Page 67 54

56 LYRA Interior Pendant/Interior Wall Integral Ballast Pages 60, 68 55

57 custom design PAVO Interior Pendant Integral Ballast Page 61 56

58 PICT Interior Pendant/Interior Wall Integral Ballast Pages 62, 69 57

59 TRYG Interior/Exterior Wall Integral Ballast Page 70 58

60 CURVUS Interior Pendant Integral Ballast Aircraft Cable 2 Lamp Fixture EMI W L H OAH SIP " 48.5" 4.7" 48.0" Up to 48" OAH W H SIP11048 shown with AP01 AP01 L AP02 Aircraft Cable 4 Lamp Fixture EMI W L H OAH SIP " 50.5" 6.8" 48.0" Up to 48" OAH H W SIP11052 shown with AP02 and BK01 AP01 AP02 L Shown with BK01 Specifications: Adjustable 48" long aircraft cables with 48" white power cord. Aluminum construction provides durable protection for internal components and is recyclable. Separate switching standard on non-dimming, non-emergency versions. (4 Lamp Only) Mounting centers adjustable from 6" - 48". Integral electronic ballast utilizes the latest energysaving technology to maintain consistent color temperature, CRI and lumen maintenance, while eliminating the need for remote mounting and simplifying installation. Ballasts are thermally protected and have Class A sound rating. Standard paint finish is thermoset polyester powder coat. Finish includes center extrusion, end caps and shielding, if specified. Custom colors available upon request. BK01 adds 2" to the length (L). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH MOUNTING OPTIONS COL ACCENTS Lamping Detail SIP11048 SIP F28 1 2F54 1 4F28 1,2 4F54 1,3 (2) F28WT5/Mini Bipin (2) F54WT5HO/Mini Bipin (4) F28WT5/Mini Bipin (4) F54WT5HO/Mini Bipin 1 T5 FL linear lamp(s) not included. 2 EMI not available. 3 EMI not available with DM option PT Painted (Include Paint Number) See STILE Finish Selection Guide on page 79. BUL Ceiling Coupler MCA 2" Mini Canopy & Aircraft Cable (with T-Bar Grip) CAA 5" Canopy & Aircraft Cable CAS 5" Canopy & Stem PCC Power Cord Canopy See page 78 for mounting details. EMI Emergency Ballast Integral F Fusing AP01 4 Perforated Accent Panel AP02 4 Slotted Accent Panel BK01 Bulkhead with Accent Tubes ABF 4 Alternate Bulkhead Finish MBP Metal Braided Power Cord SSR Symmetric Solid Reflector SPS DM Symmetric Perforated Shield Dimming CG00 White Color Gel CG01 Red Color Gel CG02 Orange Color Gel CG03 Green Color Gel CG04 Blue Color Gel See page 78 for color gels. 4 Available in a PT or BAL finish. ABF Pick accent finish for the bulkhead (Shown with PT16). Tel contact@specstile.com 59

61 LYRA Interior Pendant Integral Ballast Aircraft Cable 2 Lamp Fixture EMI W L H OAH SIP " 48.5" 3.3" 48.0" Up to 48" OAH H SIP11049 shown with AP02 AP01 W L AP02 Aircraft Cable 4 Lamp Fixture EMI W L H OAH SIP " 50.5" 3.3" 48.0" Up to 48" OAH H W SIP11053 shown with AP01 and BK01 AP01 L AP02 Specifications: Shown with BK01 Adjustable 48" long aircraft cables with 48" white power cord. Aluminum construction provides durable protection for internal components and is recyclable. Separate switching standard on non-dimming, non-emergency versions. (4 Lamp Only) Mounting centers adjustable from 6" - 48". Integral electronic ballast utilizes the latest energysaving technology to maintain consistent color temperature, CRI and lumen maintenance, while eliminating the need for remote mounting and simplifying installation. Ballasts are thermally protected and have Class A sound rating. Standard paint finish is thermoset polyester powder coat. Finish includes center extrusion, end caps and shielding, if specified. Custom colors available upon request. BK01 adds 2" to the length (L). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH MOUNTING OPTIONS COL ACCENTS Lamping Detail SIP11049 SIP F28 1 2F54 1 (2) F28WT5/Mini Bipin (2) F54WT5HO/Mini Bipin 4F28 1,2 (4) F28WT5/Mini Bipin 4F54 1,3 (4) F54WT5HO/Mini Bipin 1 T5 FL linear lamp(s) not included. 2 EMI not available. 3 EMI not available with DM option PT Painted (Include Paint Number) See STILE Finish Selection Guide on page 79. BUL Ceiling Coupler MCA 2" Mini Canopy & Aircraft Cable (with T-Bar Grip) CAA 5" Canopy & Aircraft Cable CAS 5" Canopy & Stem PCC Power Cord Canopy See page 78 for mounting details. EMI Emergency Ballast Integral F Fusing AP01 4 Perforated Accent Panel AP02 4 Slotted Accent Panel BK01 Bulkhead with Accent Tubes ABF 4 Alternate Bulkhead Finish MBP Metal Braided Power Cord SSR Symmetric Solid Reflector SPS DM Symmetric Perforated Shield Dimming CG00 White Color Gel CG01 Red Color Gel CG02 Orange Color Gel CG03 Green Color Gel CG04 Blue Color Gel See page 78 for color gels. 4 Available in a PT or BAL finish. ABF Pick accent finish for the bulkhead (Shown with PT18). 60 Tel contact@specstile.com

62 PAVO Interior Pendant Intergral Ballast Cord Mounted 2 Lamp Fixture W H OAH SIP " 71.0" 120.0" 24.0" OAH H SIP11575 shown with 24" Cord 4.0" W ACC SIP11575 shown with 24" Cord & ACC ANG Specifications: 48" white power cord standard with a white plastic canopy that fits over a standard 4" octagonal junction box. Aluminum construction provides durable protection for internal components and is recyclable. Opal diffuser lens enhances a space with filtered illumination. External fasteners are not visible, providing a clean fixture design. Standard thermoset polyester powder coat paint provides durable protection in a palette of color options. Custom colors available upon request. Integral electronic ballast utilizes the latest energysaving technology to maintain consistent color temperature, CRI and lumen maintenance, while eliminating the need for remote mounting and simplifying installation. Fixture design allows relamping without the use of tools, simplifying maintenance. Consult factory for downlight option. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE OPTIONS FINISH (for ACC or CAS only) Lamping Detail SIP F28 1 (2) F28WT5/Mini Bipin 1 T5 FL linear lamp(s) not included F Fusing ACC Decorative Accent Tube MBP Metal Braided Power Cord CAS 5" Canopy & 48" Stem ANG 2 Adjustable Angle Mount DM Dimming PT Painted. (Include Paint Number) See STILE Finish Selection Guide on page Not available with CAS. ANG Angle mount. Tel contact@specstile.com 61

63 PICT Interior Pendant Intergral Ballast Aircraft Cable 2 Lamp Fixture EMI W L H OAH SIP " 52.0" 4.3" 48.0" Up to 48" OAH H W SIP11043 shown with AP01 L AP01 AP02 AP03 SIP11043 shown with AP03 and BK01 Specifications: Adjustable 48" long aircraft cables with 48" white power cord. Mounting centers adjustable from 6" - 48". Integral electronic ballast utilizes the latest energysaving technology to maintain consistent color temperature, CRI and lumen maintenance, while eliminating the need for remote mounting and simplifying installation. Aluminum construction provides durable protection for internal components and is recyclable. Ballasts are thermally protected and have Class A sound rating. Standard paint finish is thermoset polyester powder coat. Finish includes center extrusion, end caps and shielding, if specified. Custom colors available upon request. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH MOUNTING OPTIONS COL ACCENTS Lamping Detail SIP F28 1 2F T5 FL linear lamp(s) not included. (2) F28WT5/Mini Bipin (2) F54WT5HO/Mini Bipin PT Painted (Include Paint Number) See STILE Finish Selection Guide on page 79. BUL Ceiling Coupler MCA 2" Mini Canopy & Aircraft Cable (with T-Bar Grip) CAA 5" Canopy & Aircraft Cable CAS 5" Canopy & Stem PCC Power Cord Canopy See page 78 for mounting details. EMI Emergency Ballast Integral F Fusing AP01 2 Perforated Accent Panel AP02 2 Slotted Accent Panel AP03 2 Decorative Accent Panel BK01 Bulkhead with Accent Tubes ABF 2 Alternate Bulkhead Finish MBP Metal Braided Power Cord SSR Symmetric Solid Reflector SPS DM Symmetric Perforated Shield Dimming CG00 3 White Color Gel CG01 3 Red Color Gel CG02 3 Orange Color Gel CG03 3 Green Color Gel CG04 3 Blue Color Gel 3 Not available with AP01. See page 78 for color gels. 2 Available in a PT or BAL finish. ABF Pick accent finish for the bulkhead (Shown with PT19). 62 Tel contact@specstile.com

64 ARA Interior Wall Integral Power Supply Wall Mount ADA W H D MC SIW " 13.5" 4.0" 6.0" SIW " 19.5" 4.0" 9.0" SIW " 25.5" 4.0" 12.0" H MC W D SIW11576 shown with AP01 W MC AP01 AP02 AP03 AP04 H D SIW11578 shown with AP07 AP05 AP06 AP07 AP08 Specifications: Aluminum construction provides durable protection for internal components and is recyclable. Formed metal construction provides durable protection for internal components and is recyclable. Versatile design allows fixture to be mounted in a horizontal or vertical orientation. Fixture is available in several decorative panels, enabling the fixture to blend into a space or make an artistic statement. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LEDs we use meet or exceed ANSI Binning Standards (ANSI C78.377). Compliant with Americans with Disabilities Act (ADA) requirements. Integral 24V LED, Class II power supply included, eliminating the need for remote mounting simplifying installation. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH OPTIONS Lamping Detail SIW11576 SIW11577 SIW11578 L7W L14W L22W 7.2W LED Module, 3500K 14.4W LED Module, 3500K 21.6W LED Module, 3500K PT Painted. (Include Paint Number) BAL Brushed Aluminum See STILE Finish Selection Guide on page 79. AP01 Keyhole Window AP02 Narrow Window AP03 Prairie Window AP04 Three Narrow Windows AP05 Large Window AP06 Curved Window AP07 Multi Window AP08 Slotted Windows SIW11576 shown with AP05 in horizontal orientation. Tel contact@specstile.com 63

65 BOW Interior Wall Remote Ballast/Remote Power Supply Elbow Mount Conduit Mount ADA EMR L H OAP MC SIW " 1.0" 3.0" 33.0" SIW " 1.0" 3.0" 45.0" H OAP MC L SIW9869 Elbow Mount Miniature Canopy ADA EMR L H OAP MC SIW " 1.0" 3.2" 33.0" SIW " 1.0" 3.2" 45.0" H OAP MC L SIW9878 Specifications: 1" diameter extruded tube with aluminum end caps. Conduit mount fits over standard 1/2" EMT conduit. Miniature canopy mount units include 72" flexible connection to remote ballast. (Canopy fixture only) Field adjustable housing locks into position, enabling precise fixture alignment for high-quality design performance. Standard paint finish is thermoset polyester powder coat. Custom colors available upon request. Fluorescent ballasts are thermally protected and have Class A sound rating. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LEDs we use meet or exceed ANSI Binning Standards (ANSI C78.377). Compliant with Americans with Disabilities Act (ADA) requirements. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH OPTIONS Lamping Detail SIW9869 SIW9878 SIW9870 SIW9879 L10W 1 L17W 1 1F14 2 1F24 2 L14W 1 L25W 1 1F21 2 1F Not available with EMR. 2 T5 FL linear lamp(s) not included. 9.6W LED Module, 3500K 16.8W LED Module, 3500K (1) F14WT5/Mini Bipin (1) F24WT5HO/Mini Bipin 14.4W LED Module, 3500K 25.2W LED Module, 3500K (1) F21WT5/Mini Bipin (1) F39WT5HO/Mini Bipin 24V DC LED option only. PT Painted. (Include Paint Number) AN01 Anodized Satin Aluminum See STILE Finish Selection Guide on page 79. PS W Power Supply PSE 3 Power Supply Enclosure PSN 3 Power Supply Not Included EMR 4 Emergency Ballast Remote F Fusing APS 5 Asymmetric Perforated Screen PLS 5 Perforated Lamp Shield SPS 5 Symmetric Perforated Shield TS Transluscent Shield DM 4 Dimming DML 3 Dimming 3 LED option only. 4 For Fluorescent lamping only. 5 Available in PT & AN01. See page 74 for shielding details. 64 Tel contact@specstile.com

66 BOW Interior Wall Remote Ballast/Remote Power Supply Elbow Mount Conduit Mount ADA EMR L H OAP MC SIW " 1.0" 3.0" 57.0" SIW " 1.0" 3.0" 69.0" H OAP MC L SIW9871 Elbow Mount Miniature Canopy ADA EMR L H OAP MC SIW " 1.0" 3.2" 57.0" SIW " 1.0" 3.2" 69.0" H OAP MC L SIW9880 Specifications: 1" diameter extruded tube with aluminum end caps. Conduit mount fits over standard 1/2" EMT conduit. Miniature canopy mount units include 72" flexible connection to remote ballast. (Canopy fixture only) Field adjustable housing locks into position, enabling precise fixture alignment for high-quality design performance. Standard paint finish is thermoset polyester powder coat. Custom colors available upon request. Fluorescent ballasts are thermally protected and have Class A sound rating. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LEDs we use meet or exceed ANSI Binning Standards (ANSI C78.377). Compliant with Americans with Disabilities Act (ADA) requirements. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH OPTIONS Lamping Detail SIW9871 SIW9880 SIW9877 SIW9881 L19W 1 L34W 1 1F28 2 1F W LED Module, 3500K 33.6W LED Module, 3500K 1F28WT5/Mini Bipin 1F54WT5HO/Mini Bipin L24W W LED Module, 3500K L42W W LED Module, 3500K 1F35 2,3 1F35WT5/Mini Bipin 1F80 2,3 1F80WT5HO/Mini Bipin 1 Not available with EMR. 2 T5 FL linear lamp(s) not included. 3 DM not available. 24V DC LED option only. PT Painted. (Include Paint Number) AN01 Anodized Satin Aluminum See STILE Finish Selection Guide on page 79. PS W Power Supply PSE 4 Power Supply Enclosure PSN 4 Power Supply Not Included EMR 5 Emergency Ballast Remote F Fusing APS 6 Asymmetric Perforated Screen PLS 6 Perforated Lamp Shield SPS 6 Symmetric Perforated Shield TS Transluscent Shield DM 5 Dimming DML 4 Dimming 4 LED option only. 5 For Fluorescent lamping only. 6 Available in a PT & AN01. See page 74 for shielding details. Tel contact@specstile.com 65

67 CURVUS Interior Wall Integral Ballast Wall Mount 2 Lamp Fixture ADA W H D MC SIW " 27.0" 3.0" 13.5" D MC H Auxiliary Mounting AP01 SIW11039 shown with AP01 and CG04 W Fixtures shown without faceplates. AP02 SIW11039 shown with AP02 and CG00 TS Translucent Shield SPS Symmetric Perf Shield Specifications: Curved faceplate to soften the look of the fixture. Versatile design allows fixture to be mounted in a horizontal or vertical orientation. Mounts to standard 4" octagonal junction box. Auxiliary mounting 6.75" from center provided. Formed metal construction provides durable protection for internal components and is recyclable. Integral electronic ballast utilizes the latest energysaving technology to maintain consistent color temperature, CRI and lumen maintenance, while eliminating the need for remote mounting and simplifying installation. Standard paint finish is thermoset polyester powder coat. Custom colors available upon request. Compliant with Americans with Disabilities Act (ADA) requirements. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH OPTIONS COL ACCENTS Lamping Detail SIW F14 1 2F T5 FL linear lamp(s) not included. (2) F14WT5/Mini Bipin (2) F24WT5HO/Mini Bipin PT Painted. (Include Paint Number) BAL Brushed Aluminum See STILE Finish Selection Guide on page 79. AP01 Perforated Accent Panel AP02 Slotted Accent Panel SPS Symmetric Perforated Shield TS Translucent Shield DM Dimming CG00 White Color Gel CG01 Red Color Gel CG02 Orange Color Gel CG03 Green Color Gel CG04 Blue Color Gel See page 78 for color gels. SIW11039 shown with AP02 and CG00 in horizontal orientation. 66 Tel contact@specstile.com

68 INDUS Interior Wall Integral Ballast/Integral Power Supply Wall Mount 1 Lamp Fixture ADA EMR W H D MC SIW " 32.8" 3.9" 16.4" W MC H SIW11571 SOS SSR D AOS ASR Base Model LBC 4" J-Box Cover APS SPS Specifications: Formed metal construction provides durable protection for internal components and is recyclable. Versatile design allows fixture to be mounted in a horizontal or vertical orientation. Standard paint finish is thermoset polyester powder coat. Custom colors available upon request. Integral electronic ballast or Integral 24V LED, Class II power supply included, eliminating the need for remote mounting, simplifying installation. Compliant with Americans with Disabilities Act (ADA) requirements. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LEDs we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH OPTIONS Lamping Detail SIW11571 L19W 1F W LED Module, 3500K (1) F14WT5/Mini Bipin F17 1 (1) F17WT8/Med Bipin 1F24 1 (1) F24WT5HO/Mini Bipin 1 T5 FL linear lamp(s) not included. PT Painted. (Include Paint Number) See STILE Finish Selection Guide on page 79. EMR 2 F AOS 2 APS 2 ASR 2 SOS SPS SSR LBC 3 DM 2 Emergency Ballast Remote Fusing Asymmetric Opal Shield Asymmetric Perf Screen Asymmetric Solid Reflector Symmetric Opal Shield Symmetric Perforated Shield Symmetric Solid Reflector 4" J-Box Cover Dimming SIW11571 shown in horizontal orientation. 2 Not available with LEDs. 3 Standard with LEDs. See page 74 for shielding details. Tel contact@specstile.com 67

69 LYRA Interior Wall Integral Ballast Wall Mount 2 Lamp Fixture ADA W H D MC SIW " 27.0" 2.5" 13.5" D MC H Auxiliary Mounting SIW11038 shown with AP01 and CG00 W AP01 Fixtures shown without faceplates. AP02 SIW11038 shown with AP02 and CG04 TS Translucent Shield SPS Symmetric Perf Shield Specifications: Versatile design allows fixture to be mounted in a horizontal or vertical orientation. Mounts to standard 4" octagonal junction box. Auxiliary mounting 6.75" from center provided. Formed metal construction provides durable protection for internal components and is recyclable. Integral electronic ballast utilizes the latest energysaving technology to maintain consistent color temperature, CRI and lumen maintenance, while eliminating the need for remote mounting and simplifying installation. Ballasts are thermally protected and have Class A sound rating. Standard paint finish is thermoset polyester powder coat. Custom colors available upon request. Compliant with Americans with Disabilities Act (ADA) requirements. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH OPTIONS COL ACCENTS Lamping Detail SIW F14 1 2F T5 FL linear lamp(s) not included. (2) F14WT5/Mini Bipin (2) F24WT5HO/Mini Bipin PT Painted. (Include Paint Number) BAL Brushed Aluminum See STILE Finish Selection Guide on page 79. AP01 Perforated Accent Panel AP02 Slotted Accent Panel SPS Symmetric Perforated Shield TS Transluscent Shield DM Dimming CG00 White Color Gel CG01 Red Color Gel CG02 Orange Color Gel CG03 Green Color Gel CG04 Blue Color Gel See page 78 for color gels. SIW11038 shown with AP02 and CG03 in horizontal orientation. 68 Tel contact@specstile.com

70 PICT Interior Wall Integral Ballast Wall Mount 2 Lamp Fixture ADA W H D MC SIW " 27.0" 2.3" 13.5" D MC H Auxiliary Mounting AP01 SIW11033 shown with AP01 W Fixtures shown without faceplates. AP02 AP03 SIW11033 shown with AP03 and CG04 TS Translucent Shield SPS Symmetric Perf Shield Specifications: Versatile design allows fixture to be mounted in a horizontal or vertical orientation. Mounts to standard 4" octagonal junction box. Auxiliary mounting 6.75" from center provided. Formed metal construction provides durable protection for internal components and is recyclable. Integral electronic ballast utilizes the latest energysaving technology to maintain consistent color temperature, CRI and lumen maintenance, while eliminating the need for remote mounting and simplifying installation. Ballasts are thermally protected and have Class A sound rating. Standard paint finish is thermoset polyester powder coat. Custom colors available upon request. Finish specifies aluminum panel finish. Clear acrylic panel with frosted accent and superwhite lamp engine standard. Compliant with Americans with Disabilities Act (ADA) requirements. ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH OPTIONS COL ACCENTS Lamping Detail SIW F14 1 2F T5 FL linear lamp(s) not included. (2) F14WT5/Mini Bipin (2) F24WT5HO/Mini Bipin PT Painted. (Include Paint Number) BAL Brushed Aluminum See STILE Finish Selection Guide on page 79. AP01 2 Solid Accent Panel AP02 2 Linear Accent Panel AP03 2 Decorative Accent Panel SPS Symmetric Perforated Shield TS Transluscent Shield DM Dimming 2 Available in a PT or BAL finish. CG00 3 White Color Gel CG01 3 Red Color Gel CG02 3 Orange Color Gel CG03 3 Green Color Gel CG04 3 Blue Color Gel 3 Not available with AP01. See page 78 for color gels. SIW11033 shown with AP02 and CG02 in horizontal orientation. Tel contact@specstile.com 69

71 TRYG Interior/Exterior Wall Remote Power Supply Wall Mount ADA D W W H D SIW " 26.0" 1.9" SIW " 50.0" 1.9" Exterior Wall Mount ADA H SIW11351 W H D SEW " 26.0" 1.9" SEW " 50.0" 1.9" Wall Mount ADA D W W H D SIW " 25.1" 3.8" SIW " 49.1" 3.8" H SIW11676 Specifications: Frosted acrylic shield enhances a space with diffused illumination. External fasteners are flush mounted, providing a clean design. Compliant with Americans with Disabilities Act (ADA) requirements. Versatile design allows fixture to be mounted in a horizontal or vertical orientation. Extruded aluminum construction provides durable protection for internal components and is recyclable. Anodized finish provides optimal thermal effectiveness and durable corrosion protection. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LEDs we use meet or exceed ANSI Binning Standards (ANSI C78.377). ETL listed to UL standards (US and Canada) for use in damp locations. Not recommended for exterior applications. STYLE LAMPING VOLTAGE FINISH OPTIONS Lamping Detail SIW11351 SIW11675 SEW11287 L10W B17W G17W A17W R17W 9.6W LED Module, 3500K Blue Green Amber Red 24V DC ANO4 Anodized Satin Aluminum (Clear) AN08 Anodized Black See STILE Finish Selection Guide on page 79. PS Power Supply PSE LED Power Supply Enclosure PSN Power Supply Not Included ABF 1 Alternate Bulkhead Finish CA01 Color Accent F Fusing SIW11351 shown in horizontal orientation. SIW11353 SIW11676 SEW11289 L19W B34W G34W A34W R34W 19.2W LED Module, 3500K Blue Green Amber Red 1 For & CA01 Color Accent (Shown with PT33) ABF Alternate Bulkhead Finish Higher wattage available. See online. 70 Tel contact@specstile.com

72 ARA Exterior Wall Integral Power Supply Wall Mount ADA W H D MC SEW " 13.5" 4.0" 6.0" SEW " 19.5" 4.0" 9.0" SEW " 25.5" 4.0" 12.0" H MC W D SEW11625 shown with AP08 W MC AP01 AP02 AP03 AP04 H D SEW11627 shown with AP03 AP05 AP06 AP07 AP08 Specifications: Aluminum construction provides durable protection for internal components and is recyclable. Formed metal construction provides durable protection for internal components and is recyclable. Versatile design allows fixture to be mounted in a horizontal or vertical orientation. Fixture is available in several decorative panels, enabling the fixture to blend into a space or make an artistic statement. SPI Lighting uses strict quality guidelines in LED selection to ensure the White LEDs we use meet or exceed ANSI Binning Standards (ANSI C78.377). Compliant with Americans with Disabilities Act (ADA) requirements. Integral 24V LED, Class II power supply included, eliminating the need for remote mounting simplifying installation. ETL listed to UL standards (US and Canada) for use in wet locations. STYLE LAMPING VOLTAGE FINISH OPTIONS Lamping Detail SEW11625 SEW11627 SEW11629 L7W L14W L22W 7.2W LED Module, 3500K 14.4W LED Module, 3500K 21.6W LED Module, 3500K PT Painted. (Include Paint Number) BAL Brushed Aluminum See STILE Finish Selection Guide on page 79. AP01 Keyhole Window AP02 Narrow Window AP03 Prairie Window AP04 Three Narrow Windows AP05 Large Window AP06 Curved Window AP07 Multi Window AP08 Slotted Windows SEW11627 shown with AP02 in horizontal orientation. Tel contact@specstile.com 71

73 BRACE Exterior Wall Remote Ballast Wall Mount Switch Box Cover ADA W H D MC SEW " 36.6" 3.2" 29.8" SEW " 48.3" 3.2" 41.6" SEW " 60.2" 3.2" 53.5" SEW " 72.0" 3.2" 65.2" MC H SEW10347 D W Wall Mount Standard J-Box Cover ADA W H D MC SEW " 36.6" 3.2" 29.8" SEW " 48.3" 3.2" 41.6" SEW " 60.2" 3.2" 53.5" SEW " 72.0" 3.2" 65.2" MC H SEW10348 Shown in Horizontal Orientation D W Specifications: Extruded acrylic tube with aluminum end caps maximizes output and creates uniform illumination. Remote electronic ballast utilizes the latest energy-saving technology to maintain consistent color temperature, CRI and lumen maintenance, while allowing for consolidation of ballasts. Standard thermoset polyester powder coat paint provides durable protection in a palette of color options. Custom colors available upon request. Versatile design allows fixture to be mounted in a horizontal or vertical orientation. Compliant with Americans with Disabilities Act (ADA) requirements. ETL listed to UL standards (US and Canada) for use in wet locations. STYLE LAMPING VOLTAGE FINISH OPTIONS Lamping Detail SEW10347 SEW10348 SEW10349 SEW10350 SEW10351 SEW10352 SEW10353 SEW F14 1 1F24 1 1F21 1 1F39 1 1F28 1 1F54 1 1F35 1,2 1F80 1,2 (1) F14WT5/Mini Bipin (1) F24WT5HO/Mini Bipin (1) F21WT5/Mini Bipin (1) F39WT5HO/Mini Bipin (1) F28WT5/Mini Bipin (1) F54WT5HO/Mini Bipin (1) F35WT5/Mini Bipin (1) F80WTHO/Mini Bipin 1 T5 FL linear lamp(s) not included. 2 DM not available PT Painted. (Include Paint Number) AN01 Anodized Satin Aluminum See STILE Finish Selection Guide on page 79. AOS Asymmetric Opal Shield APS 3 Asymmetric Perf Screen ASR 3 Asymmetric Solid Reflector SOS Symmetric Opal Shield SPS 3 Symmetric Perf Shield SSR 3 Symmetric Solid Reflector CT 3 AFT DM Cut-off Tube Frosted Tube Dimming 3 Available in a PT & AN01. See page 74 for shielding details. 72 Tel contact@specstile.com

74 BRACE Exterior Wall Integral Ballast Wall Mount Switch Box Cover ADA W H D MC SEW " 36.6" 4.0" 16.8" SEW " 48.3" 4.0" 22.7" SEW " 60.2" 4.0" 28.6" SEW " 72.0" 4.0" 34.5" MC H SEW10355 D W Wall Mount Standard J-Box Cover W H D MC SEW " 36.6" 4.1" 16.8" SEW " 48.3" 4.1" 22.7" SEW " 60.2" 4.1" 28.6" SEW " 72.0" 4.1" 34.5" MC H SEW10356 Shown in Horizontal Orientation D W Specifications: Extruded acrylic tube with aluminum end caps maximizes output and creates uniform illumination. Integral electronic ballast utilizes the latest energy-saving technology to maintain consistent color temperature, CRI and lumen maintenance, while eliminating the need for remote mounting and simplifying installation. Standard thermoset polyester powder coat paint provides durable protection in a palette of color options. Custom colors available upon request. Versatile design allows fixture to be mounted in a horizontal or vertical orientation. ETL listed to UL standards (US and Canada) for use in wet locations. STYLE LAMPING VOLTAGE FINISH OPTIONS Lamping Detail SEW10355 SEW10356 SEW10357 SEW10358 SEW10359 SEW F14 1 1F24 1 1F21 1 1F39 1 1F28 1 1F54 1 (1) F14WT5/Mini Bipin (1) F24WT5HO/Mini Bipin (1) F21WT5/Mini Bipin (1) F39WT5HO/Mini Bipin (1) F28WT5/Mini Bipin (1) F54WT5HO/Mini Bipin PT Painted. (Include Paint Number) AN01 Anodized Satin Aluminum See STILE Finish Selection Guide on page 79. AOS APS 3 ASR 3 SOS SPS 3 SSR 3 CT 3 AFT Asymmetric Opal Shield Asymmetric Perf Screen Asymmetric Solid Reflector Symmetric Opal Shield Symmetric Perf Shield Symmetric Solid Reflector Cut-off Tube Frosted Tube SEW10361 SEW F35 1,2 1F80 1,2 (1) F35WT5/Mini Bipin (1) F80WT5HO/Mini Bipin 3 Available in a PT & AN01. See page 74 for shielding details. 1 T5 FL linear lamp(s) not included. 2 DM not available. Tel contact@specstile.com 73

75 Technical Notes Shielding Options Beam, Bow, Brace and Indus Beam/Bow Shield Dimensions 3.8" 1.7" APS Asymmetric Perforated Screen SPS Symmetric Perforated Screen 1.5" APS Option 3.9" SPS Option 1.3" 1.4" 1.4" 1.6" PLS Option TS Option PLS Perforated Lamp Screen TS Translucent Shield Brace/Indus 6.0" 6.0" 1.5" 1.5" SOS Symmetric Opal Shield SPS Symmetric Perforated Screen SSR Symmetric Solid Reflector SOS Option SPS and SSR Option 5.0" 5.0" 3.4" 3.5" AOS Option APS and ASR Option AOS Asymmetric Opal Shield APS Asymmetric Perforated Screen ASR Asymmetric Solid Reflector 74

76 Technical Notes Controls Linear Fluorescent STILE is proud to offer controls from some of the most respected companies in the industry. We fully integrate them into our products. Just add the ordering code to your linear run, and we will take care of the rest. Contact the factory if there is another control, and we will check to assure compatibility. Lutron Ecosystem Lutron Ecosytem offers the quality and convenience of a whole system by one manufacturer, including ballasts, sensors, controls and software. LES LEF LE1 ECOSYSTEM BALLAST SENS FEED; TO INTEGRATE WALL CONTROLS, SENSS AND RECEIVERS 1.2" (30mm) DAYLIGHT SENS LUTRON CATALOG NO#EC-DIR-WH.7" (17mm) LE2 1.2" (30mm) IR RECEIVER LUTRON CATALOG NO#EC-IR-WH.7" (17mm) Lutron BALLAST LES Lutron EcoSystem Ballast LHL Lutron Hi-Lume Ballast (54W Only) LET Lutron Eco-10 Ballast LH3 Lutron Hi-Lume 3D CONTROLS LEF Lutron Sensor Feed LE1 Lutron Daylight Sensor LE2 Lutron Infrared Receiver Advance BALLAST AMX Advance Mark X (line voltage) (54W Only) AMS Advance Mark VII (0-10V) WattStopper CONTROLS WS1 Watt Stopper Daylight Sensor WSR Watt Stopper Daylight Setup Remote WSO Watt Stopper Occupancy Sensor W Watt Stopper Occupant Controller Remote WS1 WS0.2" (4mm).2" (4mm) 1.0" (25mm) DAYLIGHT SENS WATT STOPPER CATALOG NO#FD " (25mm) OCCUPANCY SENS WATT STOPPER CATALOG NO#205V2 Lynk 1 Circuit and 2 Circuit Details 1 CIRCUIT ONLY 1 CIRCUIT/2 CIRCUIT 1 CIRCUIT/2 CIRCUIT 1 CIRCUIT/2 CIRCUIT OUTSIDE ON OUTSIDE LAMPS GROUPED OUTSIDE LAMPS GROUPED 75

77 Technical Notes Power Supplies LED Determine the maximum fixture wattage per circuit by adding the wattage of each fixture together and choose an LED power supply that has an available output wattage greater than the total wattage of the fixtures. MODEL NUMBER/STYLE LED POWER SUPPLY INPUT VOLTAGE PSE OPTION CPS Not all options are available in all configurations, consult factory for details. LED POWER SUPPLY DETAILS AVAILABLE OUTPUT WATTS RATED OUTPUT WATTS INPUT VOLTAGE OUTPUT VOLTAGE DESCRIPTION PS W 75W V AC 24V DC DAMP LOCATION LISTED, CLASS PS W 96W V AC 24V DC DRY LOCATION LISTED, CLASS PS W 96W V AC 24V DC WET LOCATION LISTED, CLASS 2 IP66 RATED PS04 (2)PS W X2 75W X V AC 24V DC DAMP LOCATION LISTED, CLASS PS05 (2)PS W X2 96W X V AC 24V DC WET LOCATION LISTED, CLASS 2 IP66 RATED PS06 (2)PS W X2 96W X V AC 24V DC DRY LOCATION LISTED, CLASS PS07 (2)PS W X4 96W X V AC 24V DC WET LOCATION LISTED, CLASS 2 IP66 RATED PS08 (4)PS W X4 75W X V AC 24V DC DAMP LOCATION LISTED, CLASS PS W/CH 80W/CH V AC 24V DC WET LOCATION LISTED, CLASS 2 (3) 80W OUTPUTS, IP66 RATED, /CH3 PS W 20W/CH V AC 24V DC DAMP LOCATION LISTED, CLASS See CPS11411 for LED dimming, RGB and DMX interface options. LED Specification Notes Multiple fixtures may be connected to one LED power supply to create a circuit. Total fixture wattage should not exceed 90% of power supply rating. Use Available Output Wattage. Power Supplies are not shipped with an enclosure. PSE option will include a Damp Power Supply Enclosure. Power Supply Dimensions * Have lead wires with a direct conduit connection. 2.4" 2.4" 1.6" 9.8" 2.4" 7.6" 2.6" 12.3" 6.0" 12.0" 1.2" PS10 PS01 1.2" *PS02 1.5" *PS03 1.7" *PS04 2.4" Remote Wiring Requirements Low voltage circuits are limited by current capacity and voltage drops through conductors. Determine the appropriate cable following the Maximum Cable Length table provided. All fixtures and circuit branches are to be wired in parallel (positive to positive, negative to negative). Install and connect LED power supply to fixtures in accordance with NEC and local regulations. If remote distance is over 32', additional EMI precautions need to be taken (contact factory for assistance). Maximum Cable Length (ft) WIRE AWG V DC 20W 90' 144' 24V DC 75W 24' 38' 24V DC 96W 19' 30' 76

78 Technical Notes Controls LED.8" MODEL NUMBER/STYLE CPS LED CONTROL 6.8" DIM RGB DIM DIMMER MODULE, 1-CHANNEL, OSRAM OT DIM RGB DIMMER MODULE, 3-CHANNEL, OSRAM OT RGB DIM.1" 1.7" RGB SEQ RGB DMX RGB SEQUENCER, OSRAM OT RGB SEQ RGB DMX MODULE, 3-CHANNEL, OSRAM RGB DMX 6.5" LED Specification Notes An LED Control Module is required for each power supply. Some fixtures (over 68W) may require multiple power supplies. Contact factory for assistance. See CPS for power supply options and specification. Power supplies may be specified with fixture, as a separate component (CPS10875) or by others. If supplied by others, specifier must ensure compatibility and quality of supplies. Install and connect fixture, power supply and control module in accordance with NEC and local regulations. The "Designed to be LED" logo was created to help you identify products that were designed with LED s in mind. As a lighting fixture manufacturing company we feel it is important to design products to maximize the output of current LED technology. We utilize the latest in LED diodes, and have them added to our proprietary STILE circuit board. These products, with built in heat sinks, will perform better than a fixture where LED s were added as an afterthought. Look for the logo and know you have a high quality "Designed to be LED" product. Success with solid-state lighting We sit on the leading edge of an industry poised for explosive growth. As innovative LED lighting products emerge, the facts about LED lighting performance must hit the market with equal speed. Clear labeling on lighting performance is the critical link between innovation and successful market introduction. Lighting Facts showcases LED luminaire manufacturers who commit to testing products and reporting performance results according to industry standards. For lighting buyers, designers, and energy efficiency programs, the Lighting Facts label provides information essential to evaluating products and identifying the best options. 77

79 Technical Notes Mounting Options and Color Gels Mounting Options Ceiling W=.6" H=.9" W=2" H=1.1" W=2" H=.5" W=5" H=1.8" W=5" H=1.3" BUL.6" Ceiling Coupler MCA 2" Mini Canopy and Aircraft Cable(with T-Bar Clip) MCS 2" Canopy and Stem CAA 5" Canopy and Aircraft Cable CAS 5" Canopy and Stem W=6.2" H=.8" W=2" H=.5" H=3" H=2.1" W=2.1" CWS 6.2" Canopy and Stem PCC Power Cord Canopy BRK 3" Bracket FBK Fixed Bracket Wall H=4.4" W=2.5" H=2.5" W=4.4" H=4.4" W=4.4" W=2" H=2.4" LBK/LBI Bracket SBC Switch-Box Cover LBC 4" J-Box Cover MCS 2" Mini Canopy and Stem SMT Surface Mount W=12"-18" H=4.5" H=1.4" H=2" H=2.5" SJB Surface Mount w/standard J-Box Cover ICS 1.4" Canopy and Stem MBK 2" Mini Bracket COV Cove Mount Color Gel CG00 White CG01 Red CG02 Orange CG03 Green CG04 Blue 78

80 Technical Notes Color Chart Paint Finishes PT01 2 Superwhite PT02 1 White PT03 1 Morning Light PT04 1 Warm White PT05 1 Putty PT06 1 Warm Beige PT07 1 Light Taupe PT08 1 Medium Taupe PT09 1 Medium Gray PT10 1 Dark Gray PT11 1 Black PT12 1 Dark Chocolate PT13 1 Warm Gray PT14 1 Light Gray PT15 1 Sage PT16 1 Spruce PT17 1 Red PT18 1 Deep Red PT19 1 Blue PT20 1 Dark Green PT33 1 Dark Blue PT40 1 Yellow PT41 1 Orange PT42 1 Sky Blue PT43 1 Teal PT44 1 Green PT45 1 Purple Metallic Paint Finishes PT21 4 Pearl White PT22 4 Platinum PT27 4 Deep Copper PT28 4 Dark Stainless PT29 4 Red Brass PT31 4 Medium Bronze PT32 4 Dark Bronze PT46 3 Aluminum PT47 3 Deep Red Brass PT48 3 Brass PT49 3 Bronze Anodized Finishes AN01 Anodized Satin AN04 Anodized AN08 Anodized Black The finishes shown here are printed representations of the standard color selections available for STILE products. STILE is able to match any RAL, Pantone or custom colors. There may be slight variations in color, texture and finish between the samples shown here and the actual product finishes. If a more accurate paint color or metal finish is required, please contact us at contact@specstile.com. 1 Textured 2 Glossy 3 Metallic Textured 4 Metallic Glossy 79

81 Catalog Index Linear Series Interior Surface Mount and Suspended Name Series Lamping Page Lynk SFPP T5/T5HO 22 SFPB T5/T5HO 22 SFPT T5/T5HO 22 SFFT T5/T5HO 22 SFSP T5/T5HO 22 SFSB T5/T5HO 22 SFST T5/T5HO 22 SFBL T5/T5HO 22 SLCL LED 24 Styk SLCS LED 26 Tryg MUSR LED 28 SLCT LED 28 MUSE LED 30 SLCI LED 30 Beam SFCB T5/T5HO 32 SLCB LED 32 Wall Name Series Lamping Page Beam SFWB T5/T5HO 32 SLWB LED 32 Lynk SWPP T5/T5HO 34 SWPB T5/T5HO 34 SWPT T5/T5HO 34 SWFT T5/T5HO 34 SWSP T5/T5HO 34 SWSB T5/T5HO 34 SWST T5/T5HO 34 SWBL T5/T5HO 34 Lynk SLLS LED 36 Styk SLWS LED 38 Tryg MUWR LED 40 SLWT LED 40 Linear Series Exterior Surface Mount and Suspended Name Series Lamping Page Styk SECS LED 42 Tryg SECT LED 44 Wall Name Series Lamping Page Styk SEWS LED 46 Tryg SEWT LED 48 By Catalog Number Pendant Catalog Number Name Page SIP11043 Pictor 62 SIP11048 Curvus 59 SIP11049 Lyra 60 SIP11052 Curvus 59 SIP11053 Lyra 60 SIP11575 Pavo 61 Wall Catalog Number Name Page SIW9869 Bow 64 SIW9870 Bow 64 SIW9871 Bow 65 SIW9877 Bow 65 SIW9878 Bow 64 SIW9879 Bow 64 SIW9880 Bow 65 SIW9881 Bow 65 SIW11033 Pictor 69 SIW11038 Lyra 68 SIW11039 Curvus 66 SIW11351 Tryg 70 SIW11353 Tryg 70 SIW11571 Indus 67 SIW11576 Ara 63 SIW11577 Ara 63 SIW11578 Ara 63 SIW11675 Tryg 70 SIW11676 Tryg 70 Exterior Catalog Number Name Page SEW10347 Brace 72 SEW10348 Brace 72 SEW10349 Brace 72 SEW10350 Brace 72 SEW10351 Brace 72 SEW10352 Brace 72 SEW10353 Brace 72 SEW10354 Brace 72 SEW10355 Brace 73 SEW10356 Brace 73 SEW10357 Brace 73 SEW10358 Brace 73 SEW10359 Brace 73 SEW10360 Brace 73 SEW10361 Brace 73 SEW10362 Brace 73 SEW11625 Ara 73 SEW11627 Ara 73 SEW11629 Ara 73 By Name Family Name Catalog Number Page Ara SIW Ara SIW Ara SIW Ara SEW Ara SEW Ara SEW Bow SIW Bow SIW Bow SIW Bow SIW Bow SIW Bow SIW Bow SIW Bow SIW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Brace SEW Curvus SIW Curvus SIP Curvus SIP Indus SIW Lyra SIW Lyra SIP Lyra SIP Pavo SIP Pictor SIW Pictor SIP Tryg SIW Tryg SIW Tryg SIW Tryg SIW

82 SPI Lighting Inc. is a privately owned company headquartered just north of Milwaukee, Wisconsin. Founded in the mid-1970s, the company produces and sells commercial lighting fi xtures under three brands: SPI, Advent and Stile. Stile is a unique line of fixtures with simple, clean lines designed with today s budget and energy constraints in mind. Utilizing effi cient fl uorescent and long-lasting LEDs, Stile offers a fresh approach to multi-lamp and single-lamp linear lighting. It also provides various looks in both interior and exterior designs. Complemented by a number of crisply designed wall sconces, Stile offers a new aesthetic for contemporary environments. SPI is a recognized leader in the manufacturing of high performance ambient lighting systems. SPI produces both symmetrical and asymmetrical products available in a variety of lampings, including LED. These highly effi cient fi xtures accommodate a number of different optical systems that fulfi ll demanding energy and performance requirements in a wide range of applications. From small hallways to giant warehouses, SPI has both interior and exterior products for any size project. Advent is a complete line of architectural grade luminaires available in numerous styles, materials and fi nishes. This line offers many effi cient light sources, including LEDs, and affords designers the opportunity to choose from multiple levels of photometric performance within a single housing. While designed to fit a wide range of styles and tastes, Advent products are intentionally designed to accommodate a designer s individual application requirements, aesthetic or performance based.