HORIZONTAL BLADDER TANKS
|
|
|
- Mavis Doyle
- 5 years ago
- Views:
Transcription
1 HORIZONTAL BLADDER TANKS The Chemguard Horizontal Bladder Tank is one component in a balanced pressure foam proportioning system. It requires no external power, other than the water pressure to ensure correct operation. The horizontal bladder tanks are designed and constructed in accordance with the latest revisions to ASME code, Section VIII for unfired pressure vessels with a working pressure of 175 psi and tested to 1.3 times this pressure. SPECIFICATIONS The tank shell is constructed of SA 516 Grade 70 steel, complying with ASME specifications, possessing a tensile strength of not less than 70,000 psi. The circumferential, as well as the longitudinal body seam, are machine welded. The tank interior welds and edges are ground smooth. The tank shell water inlet and tank shell water drain is screened to prevent bladder blow out or the entrapment of debris between the tank shell and the bladder. The horizontal tank assembly is supported on two saddles welded to the tank and fitted with anchoring holes allowing easy access to the bladder drain/fill valve and the tank shell drain/fill valve. FEATURES UL Listed*. FM Approved*. Chemguard Bladder Tanks comply with the requirements of the Pressure Equipment Directive 97/23/EC. The bladder is manufactured of a vinyl based polymer. Bladder material shall have an ASTM D-412 Tensile Strength of at least 3000 psi and an ASTM D-624 Graves Tear Strength of at least 420 lbs./in. Tanks are supplied with foam concentrate discharge located at the top of the tank. Standard trim piping (vents and drains) material for non-prepiped tanks is stainless steel. All valves are labeled showing normal working position and function. Lifting lugs are permanently welded to the tank with eyes of approximately 2" diameter. Tanks contain a perforated PVC center tube that assures maximum agent discharge. All tanks are oversized to allow for any thermal expansion of the foam concentrate. All tanks are supplied with a label, which identifies the type of foam concentrate the system is designed for, the percentage ratio and the tank size. Tanks are painted red enamel. OPTIONS Coal tar epoxy for coating the interior shell of the tank (for use in salt-water environment). Sight Glass. Red epoxy finish. Custom fabrication of specialty materials, dimensions, and capacities. Actuated valves for water/concentrate. Brass or carbon steel piping for non-prepiped tanks. Insulation and heat tracing packages. Seismic designed tanks available. * Note: Listings, Approvals and/or Certifications for Chemguard foam concentrate and/or equipment are valid only when used with other Chemguard foam concentrates or equipment in a manner as outlined in the applicable Listing, Approval and/or Certification. DATA SHEET #D10D03252 REVISION: 07/2009 Page 1 of 6
2 0 /. 1 3 '! % ) 4 1 / E B J E C K C A I E C B H E B J E C L A I I A M D A A F J O, J K I A J E B J M D A L A I I A? J = E I E G K 6 D E I = O H A I K J E E O D = H H F H F A H J = = C A, - * # 9 ) 4 1 / E B J E C K C A I E C B H E B J E C L A I I A M D A A F J O, J K I A J E B J M D A L A I I A? J = E I E G K 6 D E I = O H A I K J E E O D = H H F H F A H J = = C A " $ HORIZONTAL BLADDER TANKS OUTLINE DRAWING AND NORMAL VALVE POSITION CHART. = +? A J H = J A, E I? D = H C A 5 A A J A * A M 9 = J A H 1 A J 5 A A J A! * A M 5 A A J A # * A M ) 4 VALVE DESCRIPTION NORMAL VALVE POSITION Valve No. Description Manual System Automatic System 1 Manual Foam Concentrate Shut-Off (Not Shown) N.C. N.O. 2 Water Supply Shut-Off (Not Shown) N.C. N.O. 3 Sight Gauge Shut-Off N.C. N.C. 4 Tank Shell Vent N.C. N.C. 5 Bladder Vent N.C. N.C. 6 Tank Shell Drain/Fill N.C. N.C. 7 Bladder Drain/Fill N.C. N.C. 8 Automatic Foam Concentrate Isolation (Not Shown) - N.C. 9 Fill Line Master Shut-Off N.C. N.C. N.O. - Normally Open; N.C. - Normally Closed In this arrangement, Valves listed as Not Shown are either supplied as loose ship items by Chemguard or by others. NOTES: 1. Dimensions are approximate and subject to change without notice. 2. Foam concentrate discharge pipe size: Tank sizes gallon... 2" NPT(F). Tank sizes gallon... 3" Grooved. 3. Water inlet pipe size: Tank sizes gallon... 2" NPT(F). Tank sizes gallon... 3" NPT(F). 4. When designing a building to store bladder tanks, steps shall be taken to allow for removal of the internal center tube(s). Center tubes are the full length and/or height of the bladder tank. 5. *Dimension E: For tanks 500 gallons(1,893 Liters) and larger, Dimension E is 8 in.(203.2 mm) when brass foam piping is used. Page 2 of 6
3 Horizontal Bladder Tanks - Capacity, Dimensions & Weight Chart Capacity Tank Dimensions - Inches Approx. Gallons Liters A B C D E F G H I J K L M N O P Q R Wt. Lbs , , , , , , , , , , , , * , , * , , * , , * , , * ,720 1,000 3, * ,900 1,100 4, * ,150 1,200 4, * ,370 1,300 4, * ,550 1,400 5, * ,760 1,500 5, * ,940 1,600 6, * ,130 1,700 6, * ,330 1,800 6, * ,510 1,900 7, * ,690 2,000 7, * ,030 2,100 7, * ,200 2,200 8, * ,400 2,300 8, * ,610 2,400 9, * ,780 2,500 9, * ,850 2,600 9, * ,200 2,700 10, * ,350 2,800 10, * ,500 2,900 10, * ,700 3,000 11, * ,900 3,100 11, * ,125 3,200 12, * ,350 3,300 12, * ,575 3,400 12, * ,800 3,500 13, * ,025 3,600 13, * ,250 3,700 14, * ,475 3,800 14, * ,700 3,900 14, * ,925 4,000 15, * ,150 4,100 15, * ,375 4,200 15, * ,500 4,300 16, * ,725 4,400 16, * ,925 4,500 17, * ,200 HORIZONTAL BLADDER TANK - STANDARD ARRANGEMENT Page 3 of 6
4 Horizontal Bladder Tanks - Capacity, Dimensions & Weight Chart Capacity Tank Dimensions - Millimeters Approx. Gallons Liters A B C D E F G H I J K L M N O P Q R Wt. Kg , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,893 1, , , * 1, , , , , , ,271 1, , , * 1, , , , , , , ,650 1, , , , * 1, , , , , , , , ,028 1, , , , * 1, , , , , , , , ,407 1, , , , * 1, , , , , , , ,687 1,000 3,785 1, , , , * 1, , , , , , , ,769 1,100 4,164 1, , , * 1, , , , , , , , , ,882 1,200 4,542 1, , , * 1, , , , , , , , , ,982 1,300 4,921 1, , , , * 1, , , , , , , , , ,064 1,400 5,300 1, , , , * 1, , , , , , , , , ,159 1,500 5,678 1, , , , * 1, , , , , , , , , ,241 1,600 6,057 1, , , * 2, , , , , , , , , ,327 1,700 6,435 1, , , * 2, , , , , , , , , ,418 1,800 6,814 1, , , , * 2, , , , , , , , , ,499 1,900 7,192 1, , , , * 2, , , , , , , , , , ,581 2,000 7,571 1, , , , * 2, , , , , , , , , , ,735 2,100 7,949 2, , , * 2, , , , , , , , ,812 2,200 8,328 2, , , * 2, , , , , , , , , ,903 2,300 8,706 2, , , * 2, , , , , , , , , , ,998 2,400 9,085 2, , , * 2, , , , , , , , , , ,075 2,500 9,464 2, , , * 2, , , , , , , , , , ,107 2,600 9,842 2, , , , * 2, , , , , , , , , , ,266 2,700 10,221 2, , , , * 2, , , , , , , , , , ,334 2,800 10,599 2, , , , * 2, , , , , , , , , , ,402 2,900 10,978 2, , , , * 2, , , , , , , , , , ,493 3,000 11,356 2, , , , * 2, , , , , , , , , , ,583 3,100 11,735 2, , , , * 2, , , , , , , , , , ,685 3,200 12,113 2, , , , * 2, , , , , , , , , , ,787 3,300 12,492 2, , , , * 2, , , , , , , , , , ,890 3,400 12,870 2, , , , * 2, , , , , , , , , , ,992 3,500 13,249 2, , , , * 2, , , , , , , , , , ,094 3,600 13,627 2, , , , * 2, , , , , , , , , , ,196 3,700 14,006 2, , , , * 2, , , , , , , , , , ,298 3,800 14,385 2, , , , * 2, , , , , , , , , , ,400 3,900 14,763 2, , , , * 2, , , , , , , , , , ,502 4,000 15,142 2, , , , * 2, , , , , , , , , , ,604 4,100 15,520 2, , , , * 2, , , , , , , , , , ,706 4,200 15,899 2, , , , * 2, , , , , , , , , , ,763 4,300 16,277 2, , , , * 2, , , , , , , , , , ,865 4,400 16,656 2, , , , * 2, , , , , , , , , , ,955 4,500 17,034 2, , , , * 2, , , , , , , , , , ,080 HORIZONTAL BLADDER TANK - STANDARD ARRANGEMENT Page 4 of 6
5 ORDERING INFORMATION Please specify the following: Type of tank required - Horizontal or Vertical Size of tank Exterior finish of tank Whether required for salt water environment Any other options required Below is the format for standard Chemguard Bladder Tanks: Model: CHBT-TD Size: 50 to 4500 Gallon (Horizontal Tanks) Exterior Coating (Option 1): 01 Red Enamel 02 Red Epoxy 03 Custom Interior Coating (Option 2): 01 None 02 Coal Tar 03 Custom Foam Discharge Piping (Top) (Option 3): SS Pipe/SS Valves 02 Carbon Steel Pipe/Brass Valves 03 Brass Pipe/Brass Valves Trim Piping (Vent/Fill Piping) (Option 4): SS Pipe/SS Valves 02 Carbon Steel Pipe/Brass Valves 03 Brass Pipe/Brass Valves Sight Glass (Option 5): 01 None (316 SS Trim Piping) 02 None (Carbon Steel Trim Piping) 03 None (Brass Trim Piping) 04 PVC/SS Valve 05 PVC/Brass Valve Relief Valve (Option 6): 01 None (316 SS Foam Discharge Piping) 02 None (Carbon Steel Foam Discharge Piping) 03 None (Brass Foam Discharge Piping) 04 Thermal Relief Valve 05 ASME (Full Flow), 316 SS Foam Discharge Piping 06 ASME (Full Flow), Carbon Steel Foam Discharge Piping 07 ASME (Full Flow), Brass Foam Discharge Piping Sample Part Number: CHBT-TD Page 5 of 6
6 Page 6 of 6
BALANCED PRESSURE PROPORTIONING BLADDER TANK SYSTEM
BLNCD PRSSUR PROPORTIONING BLDDR TNK SYSTM Features ccurate Proportioning of Foam Concentrate into firewater stream to produce the optimum extinguishing solution Shell constructed of Steel complying to
Horizontal Pre-Piped Bladder Tanks with Proportioner
DATA SHEET Horizontal Pre-Piped Bladder Tanks with Proportioner Features Pre-piped configurations with a wide selection of proportioner sizes, including the ANSUL FLOWMAX CL for closed-head sprinkler systems
Vertical Pre-Piped Bladder Tanks with Proportioner
DATA SHEET Vertical Pre-Piped Bladder Tanks with Proportioner Features Pre-piped configurations with a wide selection of proportioner sizes, including the ANSUL FLOWMAX CL for closed-head sprinkler systems
ANSUL. Vertical and Horizontal Bladder Tanks
NSUL SYSTEM OMPONENTS U.S..G. PPROVL NO. 162.033/14/0 REV. 0 UL EX-3933 7-1-94 Page 2-59 Vertical and Horizontal ladder Tanks PPLITION The nsul bladder tank is one component in a balanced pressure proportioning
TECHNICAL DATA OBSOLETE
March 21, 2008 Foam 180a 1. DESCRIPTION The Viking bladder tank consists of an inner tank (bladder) fabricated of a flexible material (Buna-N over nylon) and an outer tank fabricated from carbon steel.
Model MTB-ASME Horizontal Pre-Piped Bladder Tanks
DATA SHEET Model MTB-ASME Horizontal Pre-Piped Bladder Tanks Features n Pre-piped configurations with a wide selection of proportioner sizes, including the SKUM TPW-150 MK2 for closedhead sprinkler systems
Model MTB-ASME Vertical Pre-Piped Bladder Tanks
DATA SHEET Model MTB-ASME Vertical Pre-Piped Bladder Tanks Features n Pre-piped configurations with a wide selection of proportioner sizes, including the SKUM TPW-150 MK2 for closedhead sprinkler systems
Vertical & Horizontal Bladder Tank Foam Storage Devices Model MXC
1 General description The KCA bladder tank together with KCA ratio controllers, form a balanced pressure proportioning system used to mix water and firefighting foam concentrate together to produce an
TECHNICAL DATA. VERTICAL AND HORIZONTAL BLADDER TANKS MODEL VFT ASME Sec.VIII Div.1 - U-1A
Page 1 of 11 1. GENERAL DESCRIPTION The bladder tank together with ratio controllers, form a balanced pressure proportioning system used to mix water and firefighting foam concentrate together to produce
QUICK START ORDERING GUIDE. Bladder Tank Quick Start Ordering Guide
QUICK START ORDERING GUIDE Bladder Tank Quick Start Ordering Guide New Bladder Tanks - Quick Start Ordering Guide The new Bladder Tanks allow a lot of flexibility in the way they can be configured to fit
QUICK START ORDERING GUIDE. Bladder Tank Quick Start Ordering Guide
QUICK START ORDERING GUIDE Bladder Tank Quick Start Ordering Guide New Bladder Tanks - Quick Start Ordering Guide The new Bladder Tanks allow a lot of flexibility in the way they can be configured to fit
Installation & Design Maintenance for ILBP System
Installation & Design Maintenance for ILBP System Before installation of the Chemguard ILBP system(s), check all components to ensure that no damage has occurred during shipment and read the manual before
Section R Foam Systems
Section R TABLE OF CONTENTS... R-1 R-3 Concentrate Control Valves and Trim... R-4 Valve Trim for Premixed... R-4 Release Trim Packages... R-4 Foam Concentrates... R-5 Accessories, Foam Concentrates...
Section R Foam Systems
Section R TABLE OF CONTENTS... R-1 R-3 Concentrate Control Valves and Trim... R-4 Valve Trim for Premixed... R-4 Release Trim Packages... R-4 Foam Concentrates... R-5 Accessories, Foam Concentrates...
Hydraulic Concentrate Control Valve
Hydraulic Concentrate Control Valve DESCRIPTION The standard hydraulic actuated valve assembly consists of a factory assembled and tested quarter turn regular port ball valve to which a hydraulic actuator
Quality is Behind the Diamond
Quality is Behind the Diamond SKID UNIT OVERVIEW Amerex is pleased to introduce a complete line of Manual Fire Fighting Skid Units for industrial and extreme hazard environments that require maximum capacity
Wet pipe low flow foam/water manifold system
December 6, 2010 Foam 15a 1. Description With the Wet Pipe Low Flow Foam/Water Manifold System, multiple risers can be supplied from a single proportioning device. A riser manifold is installed with various
SECTION PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY
SECTION 230533 - PIPING SPECIALTIES PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Static pressure
SECTION H3 TRAYMASTER SERIES DEAERATORS
SECTION H3 TRAYMASTER SERIES DEAERATORS SAMPLE SPECIFICATIONS PART 1 GENERAL... H3-12 1.1 Packaged Deaerator Specification... H3-12 PART 2 PRODUCTS... H3-12 2.1 Deaerator... H3-12 2.2 Deaerator Vessel...
Large Capacity Dry Chemical Skid Mounted Units
DRY CHEMICAL UNITS Large Capacity Dry Chemical Skid Mounted Units Description: Amerex Dry Chemical Skid Units are designed and constructed for one-person operation and pre-pressurized ready for immediate
1541/1543 Series. Consolidated * Valves. Safety Valve
GE Oil & Gas Technical Specifications 11/2014 Consolidated * Valves 1541/1543 Series Safety Valve Designed for steam and other compressible fluids, these valves are most commonly used in pharmaceutical,
VENT SILENCER PRODUCT GUIDE
VENT SILENCER Copyright 200 by PULSCO Incorporated. All rights reserved. Reproduction without permission is prohibited. PRODUCT GUIDE PULSCO VENT SILENCER TABLE OF CONTENTS DESCRIPTION PAGE PULSCO VENT
SECTION H4 BOILERMATE DEAERATORS
SAMPLE SPECIFICATIONS PART 1 SECTION H4 BOILERMATE DEAERATORS GENERAL...H4-14 1.01 General...H4-14 PART 2 PRODUCTS...H4-14 2.01 Hardware...H4-14 A. Deaerator...H4-14 B. Make Up Valve and Controller...H4-15
Pressure Relief Valves Series. Consolidated Safety Valve
Pressure Relief Valves 1511 Series Consolidated Safety Valve Consolidated Type 1511 safety valves are designed for low pressure, steam heating boilers and steam generators as well as air service applications.
Darley UHP-HV Diesel Specification 1
Darley UHP-HV Diesel Specification 1 This dual pump is designed for either a powerhead type unit or a full module. The module provides a self-contained diesel powered slide-in type ultra high pressure
DETAILED EQUIPMENT SPECIFICATION MDAS SERIES DEALKALIZERS
5356 Hillside Avenue Indianapolis, IN 46220 P: +1 888-56-Water (569-2837) F: +1 317-255-4727 info@nancrede.com www.nancrede.com DETAILED EQUIPMENT SPECIFICATION MDAS SERIES DEALKALIZERS 1.0 SCOPE 1.1 Provide
Ford Service Saddles and Tapping Sleeves
DQS Inc. Section AA 09/2017 THE FORD METER BOX COMPANY, INC. CERTIFIED TO ISO 9001:2015 10004466 Ford Service Saddles and Tapping Sleeves Contents Recommended Product Application *Steel *C900/909*** Cast
88A-100 Series. Carbon Steel ANSI Class 150 Flanged Std. Port Ball Valve - 1-1/2 through 2 STANDARDS COMPLIANCE STANDARD FEATURES
Carbon Steel ANSI Class 150 Flanged Std. Port Ball Valve - 1-1/2 through 2 2. Retainer ASTM A108 Type 1215 3. Ball ASTM A108 Type 1215 Chrome Plated 9. Gland Plate 302 or 304 SS 10. Stem Nut 316 SS 11.
CAT231.1 SHUT OFF KIT (SOK) TO PREVENT BYPASS PRESSURE GAUGE AND TEST TAP KIT SKID MOUNTING 220V, 50HZ, 1Ø
CAT231.1 STANDARD TASK MASTER III - 1 ½ VALVE 316 SS - SIDE MOUNT SERVICE FLOW BYPASS DIAPHRAGM VALVES. ERCt ELECTRONIC TIMER 100 PSI EPOXY LINED AND COATED CARBON STEEL MINERAL TANKS ACCUMATIC BRINE SYSTEM.
DETAILED EQUIPMENT SPECIFICATION MR SERIES WATER SOFTENERS
5356 Hillside Avenue Indianapolis, IN 46220 P: +1 888-56-Water (569-2837) F: +1 317-255-4727 info@nancrede.com www.nancrede.com DETAILED EQUIPMENT SPECIFICATION MR SERIES WATER SOFTENERS 1.0 SCOPE 1.1
SECTION GENERAL-SERVICE AIR COMPRESSOR PART 1 - GENERAL
13686.00 GENERAL SERVICE AIR COMPRESSOR 221519-1 SECTION 22 1519 - GENERAL-SERVICE AIR COMPRESSOR 1.1 RELATED DOCUMENTS PART 1 - GENERAL A. Drawings and general provisions of the Contract, including General
YARWAY HANCOCK Y-PATTERN FORGED STEEL GLOBE STOP VALVES SERIES 4000
Direct contact and metal-to-metal seating make this Y-pattern globe stop valve ideal for most shut-off applications. FEATURES All valves feature integral Stellite hardfacing on both body and disc seating
FIRE PROECTION EQUIPMENT
FIRE PROECTION EQUIPMENT TO PROTECT LIVES, ASSETS AND THE ENVIRONMENT Balanced Pressure Foam Proportioning Bladder Tanks Inline Balanced Pressure Foam Proportioners Balanced Pressure Foam Proportioning
Ford Brass Saddles Style 101B and 202B
101B Ford Brass Saddles 101B and 202B 101B, 3/4" and 1" Taps 202B, 3/4" through 2" Taps Specifications Body - 85-5-5-5 brass alloy as per ASTM B62, ASTM B584 and AW WA C800. Threads may be FIP, AW WA,
LINE SILENCER. Copyright 2009 by PULSCO Incorporated. All rights reserved. Reproduction without permission is prohibited.
LINE SILENCER Copyright 2009 by PULSCO Incorporated. All rights reserved. Reproduction without permission is prohibited. PRODUCT GUIDE PULSCO LINE SILENCER TABLE OF CONTENTS DESCRIPTION PAGE PULSCO LINE
DETAILED EQUIPMENT SPECIFICATION MHC SERIES WATER SOFTENERS
2227 South Street P.O. Box 044170 Racine, Wisconsin 53404-7003 Phone: 262-681-1300 Fax: 262-681-1318 www.marlo-inc.com DETAILED EQUIPMENT SPECIFICATION MHC SERIES WATER SOFTENERS 1.0 SCOPE 1.1 Provide
TECHNICAL DATA. Notes: For use with Trim Charts on Pages 227b - d
April 15, 2011 Deluge Trim 227a Order Deluge Valve Separately This Trim Chart is for use with the following Viking Trim Sets Valve Size Galvanized Trim Part No. Brass Trim Part No. 3 (DN80) 14631-1 14631-2
Carbon Steel ANSI Class 150 Flanged Full Port Ball Valve -
Description (1/2 & 3/4 Valves) Material 2. Retainer ASTM A108 Type 1215 3. Ball ASTM A108 Type 1215 8. Stem Nut 300 Series Stainless Steel 9. Lever 300 Series Stainless Steel w/vinyl Grip 10. Stem Bearing
SECTION VIII. (Sub-section 430) Wastewater Valves and Appurtenances. 1. General thru Gate Valves thru 430-3
SECTION VIII (Sub-section 430) Wastewater Valves and Appurtenances Article Page 1. General 430-1 thru 430-2 2. Gate Valves 430-2 thru 430-3 3. Plug Valves 430-3 thru 430-4 4. Check Valves 430-4 5. Tapping
Automatic Roof Door Vents
DATA SHEET Automatic Roof Door Vents Features n UL Listed for use as an automatic smoke vent n FM Approved as an automatic door vent for use in high expansion foam systems n Available in multiple sizes
Rodney Hunt. A GA Industries Company Bascule and Pelican Gates
Rodney Hunt A GA Industries Company Bascule and Pelican Gates Hinged Crest Gates Precise Flow and Level Control Fully Functional in Ice Conditions Proven Performance One Source: Design, Build, Actuate
Series 105 Simplex Strainer Cast Iron Swing Bolt O-Ring Closure, Flanged Connection Class 125 ANSI Flat Face Flange Rating VENT 'A' FLOW
Series 105 Simplex Strainer Cast Iron Swing Bolt O-Ring Closure, Flanged Connection Class 125 ANSI Flat Face Flange Rating 1/4" NPT VENT 'A' 1/4" NPT 2 - REQ'D 'D' REQ D FOR BASKET REMOVAL 'B' FLOW 'C'
A. American National Standards Institute: 1. ANSI Z Relief Valves for Hot Water Supply Systems.
SECTION 220523 - PLUMBING VALVES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Ball valves. 2. Butterfly valves. 3. Swing check valves. 4. Spring loaded check valves. 5. Water pressure reducing
Ford Service Saddles and Tapping Sleeves
Section AA 04/2013; web revision 02/2014 Ford Service Saddles and Tapping Sleeves The Ford Meter Box Company, Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 260-563-3171
Fabricated Duplex Strainers
Applications Chemical Industry Metals & Mining Process Industry Water & Waste Water Power Industry Pulp & Paper Oil & Gas Fabricated Duplex Strainers Pressures to 1480 PSIG Temperatures to 800ºF FEATURES
Check Valve MODEL. Schematic Diagram. Product Dimensions Data:
Check Valve Simple Proven Design No-Slam Operation Drip-Tight Shut-Off No Packing Glands or Stuffing Boxes Easy to Install & Maintain 8-0 (Full Internal Port) MODEL 68-0 (Reduced Internal Port) The Cla-Val
W4100, W4200 & W4300 Electric Pump
Electric Condensate Pumps W4100, W4200 & W4300 Model W4100 W4200 W4300 Connections NPT NPT NPT Tank Material Carbon Steel Cast Iron Stainless Steel Max Disch. Press. 50 PSIG 50 PSIG 50 PSIG TMO/TMA 190
TECHNICAL DATA. Q= C v P Cv = Flow Factor (GPM/1 PSI P)
1 of 9 1. DESCRIPTION The Viking 2 (DN50) is a quick-opening, differential diaphragm, flood valve with one moving part. The deluge valve is used to control water flow in deluge and preaction sprinkler
Fixed or Semi-Fixed Foam Fire Protection Systems for Storage Tanks
Fixed or Semi-Fixed Foam Fire Protection Systems for Storage Tanks In the early years of the oil industry, fire in a storage tank was a common occurrence. Virtually all products were stored in cone roof
Series Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features
Direct contact, metal-to-metal seating, make the globe valve ideal for most shut-off applications. Features General application Designed for ASME boiler and pressure vessel code, section I applications
SV418 Series Bronze Safety Valves ASME Section VIII - NB Certified for Air, Gas, Steam, and Liquid
Safety SV418 Series Bronze Safety Description Spirax Sarco's SV418 safety and relief valve is designed for accuracy and reliability. Engineered for heavy-duty industrial usage. Multiple purpose safety
Pressure Relief Valves. 1541/1543 Series. Consolidated Safety Valve
Pressure Relief Valves 1541/1543 Series Consolidated Safety Valve Table of Contents Conversion Table 1541/1543.2 Features & Benefits 1541/1543.3 Applications 1541/1543.3 Scope of Design 1541/1543.4 Materials
SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems.
SECTION 210500 - COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe, fittings, valves, and connections for sprinkler systems. 1.2 RELATED REQUIREMENTS A. Section 099000
High Pressure 2-way 2 1/2-6 Globe Valves
Overview Datasheet High Pressure 2-way 2 1/2-6 Globe Valves Designed to work with either an electronic actuator with a 3/4-inch (20 mm) or 1-1/2-inch (40 mm) stroke, the two-way globe valves are available
1.1 PURPOSE A. This section is intended to define the general installation and minimum product requirements for hydronic and steam valves.
Date Description of Change Pages / Sections Modified ID 6/15/16 Entire document - mgl44 PART 1 - INTRODUCTION 1.1 PURPOSE A. This section is intended to define the general installation and minimum product
SECTION DOMESTIC-WATER PACKAGED BOOSTER PUMPS
SECTION 221123.13 - DOMESTIC-WATER PACKAGED BOOSTER PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
CAT231.1 PRESSURE GAUGE AND TEST TAP KIT SKID MOUNTING 220V, 50HZ, 1Ø OPERATING CONDITIONS 25 TO 100 PSI 100 F MAX IMUM TEMPERATURE SERIES METER
CAT231.1 STANDARD FEATURES TASK MASTER III - 1 ½ / 2 - FIVE CYCLE 316 STAINLESS STEEL VALVE - SIDE MOUNT SUPER FLOW KIT S ON 2, 3 & 4 SYSTEMS (SERVICE FLOW BYPASS DIAPHRAGM VALVES) ERCt ELECTRONIC TIMER
87A-200 Series. Stainless Steel ANSI Class 150 Flanged Full Port Ball Valve - 1/2 through 1 STANDARD FEATURES STANDARDS COMPLIANCE
Description (1/2 & 3/4 Valves) 2. Retainer ASTM A276 Type 316 3. Ball ASTM A276 Type 316 8. Stem Nut 300 Series Stainless Steel 9. Lever 300 Series Stainless Steel w/ Vinyl Grip 10. Stem Bearing RPTFE
KINGSTON. KNG Series Product Catalog. Ph: Toll:
KEst.1908 KINGSTON KNG Product Catalog Storm Manufacturing Group, Inc. 23201 Normandie Ave., Torrance, CA 90501-5050 Ph: 310.326.8287 Toll: 800.210.2525 Email: sales@kingstonvalves.com Kingston Safety
Foam Ratio Controller Proportioning Devices Model KFP
1 General description The KCA ratio controller accurately proportions foam concentrate into a water stream over a wide range of water flow rates. The controller proportions foam at concentrations of 1%
SECTION PANELBOARDS
SECTION 16470 PANELBOARDS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. The general provisions of the contract including General and Special Conditions and General Requirements shall apply to all work under
Series Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications.
7 YARWAY Hancock T-Pattern Globe valves Direct contact and metal-to-metal seating makes the T-pattern globe stop valve ideal for most shut-off applications Features Heavy integral stellite hardfacing on
SECTION VALVES PART 1 -GENERAL
SECTION 1571 0 VALVES PART 3- EXECUTION General Shut-off Valves Balancing Valves Drain Valves RELATED WORK Section 15430- Plumbing Specialties Section 15450- Plumbing Equipment PART 1 -GENERAL SCOPE This
MODULATING FLOAT CONTROL VALVE
PROJECT NAME LOCATION MODULATING FLOAT CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 2 in. (50 mm) through 36 in. (900 mm) Control Valves PART 1 - GENERAL
Guide Specification SECTION HYDRONIC PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY
SECTION 23 21 16 - HYDRONIC PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Air
DSZ3. EBARA Submersible Propeller Pumps Contents Project: Model: Chk d: Date: Model
Contents Model A0553 C1125 V0494 A0713 C1285 V0554 A0843 C1455 V0754 A1003 C1605 V0854 C1915 V0974 C2185 V1154 C2905 Section Page Specifications 3-203 Model Designation 3-206 Impeller Data 3-208 Material
SAMPLE SPECIFICATIONS
SAMPLE SPECIFICATIONS CONTENTS PART 1 GENERAL...H1a-12 1.1 DEAERATOR SPECIFICATION...H1a-12 PART 2 PRODUCTS...H1a-12 2.1 HARDWARE...H1a-12 A. Deaerator...H1a-12 B. Make Up Valve and Controller...H1a-14
SECTION PUMPS GENERAL PUMPS PART RELATED DOCUMENTS
SECTION 15160 - PUMPS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Basic Requirements: Provisions of Section 15010, BASIC MECHANICAL REQUIREMENTS and Section 15030, ELECTRICAL REQUIREMENTS FOR MECHANICAL
YStrainers. Applications. Pressures to 3705 PSIG Temperatures to 800ºF FEATURES MATERIALS END CONNECTIONS RATINGS SIZES
Applications Process Industry Metals and Mining Power Industry Water and Waste Chemical Industry Pulp and Paper Oil and Gas YStrainers Pressures to 3705 PSIG Temperatures to 800ºF FEATURES Low pressure
505F. Multi-Port Ball Valve. Full Port ISO 5211 Mounting Pad. For Automated & Manual Service. General Chemical. Industrial
505F Multi-Port Ball Valve Full Port ISO 5 Mounting Pad For Automated & Manual Service General Chemical Industrial and Other Corrosion Resistant Applications The 505F Series 3//5-Way Ball Valve The 505F
Foam Maker Discharge Devices Model KLF
1 General description Foam makers are in-line fixed foam aspirating devices. They are used in low expansion foam discharge applications to protect tank farm dikes and other low-level discharge applications.
TECHNICAL DATA. Q= C v P S
1 of 9 1. DESCRIPTION The Viking Model E-1 Deluge Valve is a quick-opening, differential diaphragm, flood valve with one moving part. The deluge valve is used to control water flow in deluge and preaction
GENERAL FEATURES / SPEC M&H AWWA C502 FIRE HYDRANTS Style 929 Traffic Model 250 PSI Working Pressure 500 PSI Hydrostatic Test AWWA UL / FM Approval Type: Compression type, opening against line pressure.
505F Multi-Port Ball Valve
505F Multi-Port Ball Valve Full Port ISO 5 Mounting Pad For Automated & Manual Service General Chemical Industrial Corrosion Resistant Applications The 505F Series Ball Valve The 505F is a true multi-way
CASH VALVE K SERIES BACK PRESSURE VALVES
High capacity angle bypass regulators or back pressure control valves with models for pressures to 1500 psig (103.4 barg) and capacities to 200 gallons per minute (757 l/min.) FEATURES GENERAL APPLICATION
SECTION FACILITY FUEL OIL PIPING
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Specification Sections, apply to this Section. B. Related Sections:
LPCO 2 System. Refrigerated Storage Units FEATURES
LPCO 2 System Refrigerated Storage Units Janus Fire Systems Low Pressure Carbon Dioxide Refrigerated Storage Units are specifically designed to store the carbon dioxide agent supply utilized in the Janus
Fabricated Tee Strainers Style T & TQ; 150#, 300# and 600# Flanged or Butt Weld Connections...6 Technical Data...7
07/1 Fabricated Strainers Fabricated Y Strainers Style FSA & FSSA; 10#, 00# and 600# Flanged or Butt Weld Connections... Technical Data... Style FSA & FSSA; 900#, 100# and 00# Flanged or Butt Weld Connections...*
HANGERS, STRUT, AND FITTINGS SUBMITTAL
HANGERS, STRUT, AND FITTINGS SUBMITTAL Prepared By: Submitted by: Enter Company Name INTERNATIONAL SEISMIC APPLICATION TECHNOLOGY A Division of Tomarco Contractor Specialties Enter Project Name 4848 Northam
Instruction Sheet. 1/2 HP Portable Electric Pumps SAFETY FIRST. L2062 Rev. F 02/ IMPORTANT RECEIVING INSTRUCTIONS 2.
Instruction Sheet 1/2 HP Portable Electric Pumps L2062 Rev. F 02/12 Index: English:...................................... 1-7 Français:.................................... 8-14 Deutsch:...................................
ALTITUDE CONTROL VALVES FOR ONE WAY FLOW
PROJECT NAME LOCATION ALTITUDE CONTROL VALVES FOR ONE WAY FLOW INTRODUCTION This specification covers the design, manufacture, and testing of 2 in. (50 mm) through 36 in. (900 mm) Control Valves PART 1
TUV India Private Ltd. APPROVED
TUV India Private Ltd. DELUGE VALVES HD Deluge Valves are automatic reset or field manual reset type. The valves are intended for use in deluge, pre-action, foam water system and many more fire protection
Kingston Safety Relief Valves
Kingston Safety Relief Valves ASME Section VIII - NB Certified for Liquid, Air/Gas and Steam The safety and relief valve is designed for accuracy and reliability. Engineered for heavy-duty industrial usage.
Distributed By: M&M Control Service, Inc
Fabricated Strainers Fabricated Y Strainers Style FSA & FSSA; 150#, 300# and 600# Flanged or Butt Weld Connections...2 Technical Data...3 Style FSA & FSSA; 900#, 1500# and 2500# Flanged or Butt Weld Connections...*
Spring loaded Thermal Relief Safety Valves, manufacturers standard Medium and high pressure
Series Thermal Relief Safety Valves Spring loaded Thermal Relief Safety Valves, manufacturers standard Medium and high pressure Applications The Sempell series provides a complete and comprehensive range
TStrainers. Applications. Pressures to 3705 PSIG Temperatures to 800ºF FEATURES MATERIALS END CONNECTIONS SIZES RATINGS
Applications Steam, Liquid, Gas and Oil Service Process Equipment Water and Waste Power Industry Pulp and Paper Chemical Industry Metals and Mining TStrainers Pressures to 3705 PSIG Temperatures to 800ºF
Page 6-6. Page 6-3. Page 6-3. Page 6-5. Self- Educting Foam. Foam Compatible. Location
SELECTOR GUIDE 6-1 AUTOMATIC AUTOMATIC X-STREAM SM-10FE AVAILABLE BASE 1.5 2.5 3.5 1.5 2.5 3.5 300-2000 (1136-7571) 20-120 (76-454) PRODUCT DESCRIPTION MATERIAL Page 6-6 Page 6-3 Simplifies fireground
Features 1. Differential Latch-type, lightweight, dependable
Bulletin 516 Rev. B Model DDX-SS Deluge Valve (100mm), (150mm) & (200mm) Bulletin 516 Rev. B Features 1. Differential Latch-type, lightweight, dependable construction. 2. Easily trimmed for releasing by:
MCS TYPE B FOAM MAKER & FOAM CHAMBER NDD010. Approvals: UL, ULC
Approvals: UL, ULC Superior Foam Quality Operates At 30 PSI (2.1 bar) Minimum Tool Free Maintenance Corrosion Resistant Polyester Finish Double Aeration Foam Maker Description The MCS Foam Maker and Foam
PRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE
PROJECT NAME LOCATION PRESSURE RELIEF / SURGE ANTICIPATOR CONTROL VALVE INTRODUCTION This specification covers the design, manufacture, and testing of 2-1/2 in. (65 mm) through 18 in. (450 mm) Control
Foam Supply Kits FOAM EDUCTORS FOAM EDUCTORS FOAM EDUCTORS FOAM SUPPLY KITS
FOAM SUPPLY KITS Foam Supply Kits Elkhart offers two supply kits. Both kits include: One.75 quarter-turn, inlet valve assembly with elbow Quick-connect female coupling Quick-connect plug with chain Brushed
Foam Supply Kits FOAM EDUCTORS FOAM EDUCTORS FOAM EDUCTORS FOAM SUPPLY KITS
FOAM SUPPLY KITS Foam Supply Kits Elkhart offers two supply kits. Both kits include: One.75" quarter-turn, inlet valve assembly with elbow Quick-connect female coupling Quick-connect plug with chain Brushed
JST Series. Cemline STONESTEEL Jacketed Storage Tanks
JST Series Cemline STONESTEEL Jacketed Storage Tanks STONESTEEL is a registered trademark of Cemline Corporation CEMLINE CORPORTION P.O. BOX 55 CHESWICK, PENNSYLVNI 15024 Phone: (724) 274-5430 FX: (724)
Foam Chambers DATA SHEET. Features. Application. Flow Range. Description
DATA SHEET Foam Chambers Features n Choice of four foam chamber sizes for various foam solution flow rate requirements n Hinged inspection hatch with captive bolt securement for ease of inspection and
TEMPERATURE REGULATORS W91/W94 Series
Self-Operated Temperature Regulators Watson McDaniel reserves the right to change the designs and/or materials of its products without notice. 2010 Watson McDaniel Company Self-Operating Design Indicating
A. This Section includes piping and related specialties for general-service compressed-air systems operating at 150 psig or less.
SECTION 221513 - COMPRESSED-AIR PIPING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes piping and related specialties for general-service compressed-air systems operating at 150 psig or less. 1.2
ASME Section I and VIII - NB Certified for Air/Gas and Steam. Series 560. Series 570. Series Stainless steel whetted trimming.
SAFETY VALVES Safety Valves SIZES FROM 1/2 TO 2 1/2 RATED TO 300 PSI TEMPERATURES TO 450 F ASME Section I and VIII - NB Certified for Air/Gas and Steam Aquatrol s Series / valve line is a high capacity
P40 Series Foam Concentrate Pump
Description Chemguard foam concentrate pumps are constructed of corrosion resistant brass and stainless steel, and are designed for use with all types of fire fighting foam concentrates. The pumps are
26000 litre ISOTANK SPECIFICATION FOR HAZARDOUS CHEMICALS TRANSPORT AND STORAGE SPECIFICATION T11.
26000 litre ISOTANK SPECIFICATION FOR HAZARDOUS CHEMICALS TRANSPORT AND STORAGE SPECIFICATION T11. DESCRIPTION: 26 000 LITRE INSULATED UN PORTABLE TANK, TYPE T11 For transport of product classes 3, 4,
TRUNNION MOUNTED METAL SEATED BALL VALVES
TRUNNION MOUNTED METAL SEATED BALL VALVES HIGH PERFORMANCE BALL VALVES FOR SEVERE SERVICES PROCESS VALVES STANDARD FEATURES FOR SIDE ENTRY & BOTTOM ENTRY DESIGN 1. Trunnion Mounted The ball is trunnion