Volute Casing Centrifugal Pumps of Inline Design Series NI
|
|
- Nathan Bryant
- 5 years ago
- Views:
Transcription
1 Volute Casing Centrifugal Pumps of Inline Design Series NI Application For pumping pure water, industrial water, sea water, condensates, oils, brines, lyes and hot water. The fluids to be pumped must not contain any abrassive particles nor chemically attack the pump materials. Main fields of application In cooling and heating systems, in circulating, water supply, water treatment, seawater desalination, dedusting and spray painting plants as well as in airconditioning, cooling, swimming pool and industrial engineering. Design and series construction Volute casing centrifugal pump, single entry, single or twostage, of inline design. Pump according to DIN EN 733. Stub and motor shaft are rigidly coupled together. bearing in the motor by means of greaselubricated groove ball bearings. The mating dimensions of the twostage s 2/25 200/01, 2/32 200/01, 2/40 250/01, 2/50 250/01, except for dimensions f and l depending upon the driving motors, correspond to the singlestage designs. Horizontal or vertical installation, motor arrangement downwards is not admissible. Performance data Delivery Q up to 380 m 3 /h Delivery head H up to 145 m Temperature of the fluid pumped t up to 140 C Inlet pressure p s Pump outlet pressure as a function of the shaft diameter and the with diameter 16, 24, 30 p d up to 16 bar with diameter 40 p d up to 10 bar Drive power P 0,25 up to 37 kw Nominal diameter, delivery flange DN d 25 up to 150 Branch position/flanges Suction and outlet branch opposite in one line. Flanges: up to DN 150 acc. to EN PN 16 up to DN 200 acc. to EN PN 10 Explosion protection The pump fulfils the requirements according to EC Explosion Protection Directive 94/9EG (ATEX 100a) for equipment and equipment group II, category 2 G. Categorisation into temperature classes according to EN depends on the temperature of the pumped medium. The max. permissible temperature of the pumped medium for the respective temperature classes are shown in the specific order data sheet. Note: In case of the operation of a category 2 pump, the unacceptable heating of the pump surfaces caused by a possible operational fault must be prevented by a control mechanism. In case of an operation with constant parameters (pressure, temperature, speed = const.), a pump performance controller can be supplied with the pump to detect any operational faults. Drive Surfacecooled threephase squirrelcage induction motors, with locatingtype bearing, IM V1 type of construction, enclosure IP55 according to IEC Standard, class F insulation, performances and main dimensions according to DIN , up to 2.2 kw 230/400V, from 3 kw 400/690 V. Attention: Motors provided by customers must also have a locatingtype bearing! Dismantling the driving unit When dismantling the driving unit, the volute casing may remain in the piping. Connections The following auxiliary connections are always provided: FD Draining FF Filling FV Venting PM1 Pressure measurement pump PM2 Pressure measurement pump inlet pressure plus maximum delivery head must not exceed the admissible pump outlet pressure allocation pump / shaft diameter at the, refer to pages 10 to 16 in case the temperature of fluids pumped exceeds 120 C, the admissible pump outlet pressure changes as follows: Contact protection The requirements of DIN EN 809 Contact protection, are met. seal By maintenancefree mechanical seal in unbalanced design (main dimensions acc. to DlN EN , design K, shape U). Combination of components The table on page 3 shows the combination possibilities of components of all Nl s. The unit assembly system allows reduced stockkeeping of spare parts. Connection PM1 only with shaft diameter 40 at the VM 527 GB/05.06 Ident No
2 seals with temperature and pressure limits Available for all material designs Mechanical seal, uncooled Unbalanced Flushing Internal flushing Internal flushing bores Abbreviation U3D U3.1D U 3.9D U3.12D U3.20D U3.10K U3.11K Rotating seal ring Hard carbon, synthetic resin impregnated Silicon carbide Hard carbon, antimony impregnated Hard carbon, synthetic resin impregnated Stationary seal ring Oxide ceramics Silicon carbide Silicon carbide Metal parts CrNiMo steel CrNiMo steel CrNiMo steel Orings EPDM FPM EPDM FPM EPDM EPDM Viton Bellows EPDM FPM Material key, DIN EN Volute casing centrifugal pumps at bearing bracket singlestage BVEGG BVVGG Q1Q1EGG Q1Q1VGG AQ1EGG BQ1EGG BQ1VGG Admissible temperature of the fluid pumped ( C) and admissible pump outlet pressure p d (bar) C / bar C / bar C / bar C / bar C / bar C / bar C / bar 100 / / / / / / / 12 twostage 100 / / / / / 16 applies to water max. 90 C only possible for s with shaft diameters 16, 24, 30 (at the ) in case of inlet pressure > 5 bar, U3.20 D or U3.10 K must be provided Other mechanical seal designs on inquiery. 120 / / 12 Abbreviation system NI / 01 / 180 U3D W3 38 / 300 Series Size Hydraulic no. Standard nominal width on delivery side Nominal impeller diameter Actual impeller diameter seal Material design Stub shaft bore diameter for fixing to motor shaft end Drive lantern or intermediate ring outside diameter or flange of electric motor The actual impeller diameter of twostage s relates to the second stage. The number of stages is placed in front of the nominal width of the outlet branch, e.g. 2/40 200/... Materials Denomination Part No. Material designs singlestage twostage W 3 W 18 W 19 W 88 W 97 Volute casing CC333G ENGJL250 ENGJL250 ENGJS40015 ENGJS40015 Impeller CC333G CC333G ENGJL200 CC333G ENGJL200 Impeller 1st stage CC333G CC333G ENGJL200 CC333G ENGJL200 Impeller 2nd stage CC333G CC333G ENGJL200 CC333G ENGJL200 Diffuser CC333G CC333G ENGJL200 CC333G ENGJL200 Stage casing CC333G ENGJL250 ENGJL250 ENGJS40015 ENGJS40015 Casing cover CC333G ENGJL250 ENGJL250 ENGJS40015 ENGJS40015 Stub shaft / / / / / Drive lantern ENGJL250 ENGJL250 ENGJL250 ENGJL250 ENGJL250 Intermediate ring CC333G ENGJL250 ENGJL250 ENGJS40015 ENGJS40015 Intermediate ring ENGJL250 or St ENGJL250 or St ENGJL250 or St ENGJL250 oder St ENGJL250 oder St in contact with fluids / motor side VM 527 GB/05.06 Ident No
3 Combination of components The following table shows the combination possibilities of components or spare parts of the NI s. Within a vertical column, parts with identical numbers are interchangeable. diameter at the Pump Volute casing Impeller Impeller Diffuser Stage Intermediate Casing Stub shaft Drive casing cover lantern ring Intermediate ring mm NI 1 st stage 2 nd stage / / / / / The allocation to the s depends on speed, motor performance and motor design / / / / / / / / / / / / two stage 2/25200/01 6 2/32200/ /40250/ /50250/ /3019 2/3024 2/3028 2/3038 2/3042 2/3048 2/ / / / / / / / / / / VM 527 GB/05.06 Ident No
4 Commercial standard motors with locatingtype bearing, construction IM V1, all types of enclosures and speeds of rotation possible. Horizontal and vertical mounting possible with exception of motor downward. Uncooled, unbalanced mechanical seal for cavities according to DIN EN , design K, form U. When dismantling the driving unit (including impeller) the volute casing remains in the piping. Negligible axial thrust by fine adaption of the balancing holes. Optimized hydraulic with very good efficiencies and NPSHvalues of the standard series NT acc. to DIN EN 733, delivery rate partly considerable above the standard demands. No foundation necessary. Larger delivery heads with twostage s (2/25200/01, 2/32200/01, 2/40250/01, 2/50250/01). The outer dimensions correspond with the single stage design. 4 VM 527 GB/05.06 Ident No
5 Performance graphs n = /min n = /min For exact performance data, please refer to the individual characteristics. Valid for ρ = 1 kg/dm³ and ν = 1 mm²/s VM 527 GB/05.06 Ident No
6 n = /min n = /min For exact performance data, please refer to the individual characteristics. Valid for ρ = 1 kg/dm³ and ν = 1 mm²/s 6 VM 527 GB/05.06 Ident No
7 Sectional drawing Singlestage s with shaft diameter 16 at the Fixing of guard plate to the drive lantern. Protection against accidental contact acc. to DIN EN 809 Denomination Part No. Denomination Part No. Denomination Part No. Volute casing.01 Washer Socket head cap screw Casing cover Rivet Impeller nut Stub shaft Bleeder screw Spring washer Impeller Guard plate Key Drive lantern Flangemounted motor Rating plate Gasket Hexagonal screw Joint ring Hexagonal screw Joint ring Hexagonal screw Connections Joint ring Hexagonal screw FD Drainage Mechanical seal Screwed plug FV Venting Spacer sleeve Screwed plug PM2 Pressure measurement VM 527 GB/05.06 Ident No
8 Sectional drawing Singlestage s with shaft diameters 24 and 30 at the Casing cover design at s 2/40250/01 and 2/50250/01 seal: uncooled, unbalanced mechanical seal Abbreviation: U 3 D Fixing of guard plate to the drive lantern. Protection against accidental contact acc. to DIN EN 809 Sizes with diameter 24 at the Design with intermediate ring, s 40250/01 and 50250/01 Twostage s with shaft diameter 30 at the, uncooled, unbalanced mechanical seals U 3 D and U 3.20 D 8 VM 527 GB/05.06 Ident No
9 Sectional drawing Sizes with shaft diameter 40 at the Design with intermediate ring, s 65315/01, 80315/01, /01, 65400/01 seal: uncooled, unbalanced mechanical seal Abbreviation: U 3 D Fixing of guard plate to the drive lantern. Protection against accidental contact acc. to DIN EN 809 Denomination Part No. Denomination Part No. Denomination Part No. Volute casing.01 Intermediate ring Socket head cap screw Stage casing Intermediate ring Socket head cap screw Casing cover Threaded ring Socket head cap screw Casing cover Spacer sleeve Socket head cap screw Casing cover Spacer sleeve Hexagonal nut Diffuser Washer Hexagonal nut Stub shaft Rivet Impeller nut Stub shaft Bleeder screw Spring washer Impeller Guard plate Key Impeller 1 st stage Flangemounted motor Key Impeller 2 nd stage Hexagonal screw Rating plate Drive lantern Hexagonal screw Gasket Hexagonal screw Gasket Hexagonal screw Joint ring Stud bolt Joint ring Stud bolt Connections Joint ring Screwed plug FD Drainage Joint ring Screwed plug FF Filling Joint ring Screwed plug FV Venting Oring Screwed plug PM1 Pressure measurement Mechanical seal Grub screw PM2 Pressure measurement VM 527 GB/05.06 Ident No
10 n = 1450/1750 1/min Aggregate dimensions Sizes with shaft diameters 16, 24, 30, and 40 at the DNd DNs Flanges acc. to EN PN 16 D bf k g No. of holes diameter at the shaft seal Connections Pressure measurement mm FD FF FV PM1 PM2 16 G 1/4 G 1/8 G 1/4 24, 30 G 3/8 G 3/8 G 1/4 G 3/8 40 G 3/8 G 3/8 G 3/8 G 1/2 G 3/8 Tolerances of companion dimensions acc. to DIN EN 735 Sense of rotation: clockwise as seen from the driving side Dimensions in mm without commitment diameter at 10 mm Pump / / / / / /01 Extension dimension 2/25 200/ / /01 Motor Performance Flanges Pump dimensions Aggregate dimensions Motor dimensions approx. dimensions varying depending upon manufacturer Draining Filling Venting Allocation stub shaft/ drive lantern Contained in abbreviation, kw DN s DN d a f a 2 b 1 b 2 f 1 h 1 h 2 a 1 d h 3 I 1 l x v. page ,25 0, / ,55 0, / ,25 0, / ,55 0, / S 1, / ,25 0, / ,55 0, / S 1, / ,25 0, / ,55 0, / S 1, / L 1, / L 2, ,25 0, / ,55 0, / S 1, / L 1, / L 2, ,55 0, / S 1, / L 1, / ,55 0, / S 1, / L 1, / L 2, ,55 0, / S 1, / L 1, / L 2, ,55 0, / S 1, / L 1, / L 2, VM 527 GB/05.06 Ident No
11 n = 1450/1750 1/min diameter at mm 30 Pump 2/32200/ / / /01 2/40250/ / / /01 2/50250/ / / /01 Motor Performance Flanges Pump dimensions Aggregate dimensions Motor dimensions approx. dimensions varying depending upon manufacturerr kw DN S DN d a f a 2 b 1 b 2 f 1 h 1 h 2 a 1 d h 3 I 1 I x Extensiondimension Allocation stub shaft/ drive lantern/ intermediate ring Contained in abbreviation, v. page ,55 0, / S 1, / L 1, / L 2, ,55 0, / S 1, / L 1, / L 2, ,55 0, / S 1, / L 1, / L 2, S 1, / L 1, / L 2, L 2, S 5, / / M ,55 0, / S 1, / L 1, / L 2, ,55 0, / S 1, / L 1, / L 2, S 5, / L 1, / L 2, S 5, / / M L 2, S 5, / / M L ,55 0, / S 1, / L 1, / L 2, S 1, / L 1, / L 2, S 5, / / L 2, S 5, / / M L M 18, /350 The motor dimensions as indicated are approximate dimensions. Exact data depend on the motor make. When using spezial motors, make sure that other performances are allocated to the individual s, depending upon the enclosure. The main dimensions change accordingly. In case of order, binding tables of motor dimensions must be supplied to us. VM 527 GB/05.06 Ident No
12 n = 1450/1750 1/min Aggregate dimensions Sizes with shaft diameter 30 and 40 at the Flanges up to DN 150 acc. to EN PN 16 up to DN 200 acc. to EN PN 10 DNd DNs D bf k g No. of holes diameter at shaft seal Draining Connections Pressure measurement mm FD FF FV PM1 PM2 30 G 3/8 G 3/8 G 1/4 G 3/8 40 G 3/8 G 3/8 G 3/8 G 1/2 G 3/8 Tolerances of companion dimensions acc. to DIN EN 735 Sense of rotation: clockwise, as seen from the driving side Dimensions in mm without commitment diameter at the mm 40 Pump 65315/ / /01 Motor Performance Flanges Pump dimensions Aggregate dimensions Motor dimensions approx. dimensions varying depending upon manufacturer Filling Venting Extension dimension Allocation stub shaft/ drive lantern/ intermediate ring Contained in kw DN S DN d a f a 2 b 1 b 2 f 1 h 1 h 2 a 1 d h 3 I 1 l x abbreviation v. page S 5, / / M L M 18, / L / L / M L M 18, / L / L ,55 0, /200 90S 1, / L 1, / L 2, S 5, / / VM 527 GB/05.06 Ident No
13 n = 1450/1750 1/min diameter at the mm 40 Pump 80200/ / / / / / /01 Motor Performance Flanges Pump dimensions Aggregate dimensions Motor dimensions approx. dimensions varying depending upon manufacturer kw DN S DN d a f a 2 b 1 b 2 f 1 h 1 h 2 a 1 d h 3 I 1 I x Extension dimension Allocation stub shaft/ intermediate ring Contained in abbreviation v. page L 2, S 5, / / M S 5, / / M L M 18, / L / L S 5, / / M L M 18, / L / L L 2, S 5, / / M L S 5, / / M L M 18, / L / L / M L M 18, / L / L / M L M 18, / L / L The motor dimensions as indicated are approximate dimensions. Exact data depend on the motor make. When using special motors, make sure that other performances are allocated to the individual s, depending upon the enclosure. The main dimensions change accordingly. In case of order, binding tables of motor dimensions must be supplied to us. VM 527 GB/05.06 Ident No
14 n = 2900/3500 1/min Aggregate dimensions Sizes with shaft diameters 16, 24, 30 and 40 at the DNd DNs Flanges acc. to EN PN 16 D bf k g No. of holes diameter at the Filling Connections Pressure measurement mm FD FF FV PM1 PM2 16 G 1/4 G 1/8 G 1/4 24, 30 G 3/8 G 3/8 G 1/4 G 3/8 40 G 3/8 G 3/8 G 3/8 G 1/2 G 3/8 Tolerances of companion dimensions acc. to DIN EN 735 Sense of rotation: clockwise, as seen from the driving side Dimensions in mm without commitment diameter at Pump Motor Performance Flanges Pump dimensions Aggregate dimensions Motor dimensions approx. dimensions varying depending upon manufacturer mm kw DN S DN d a f a 2 b 1 b 2 f 1 h 1 h 2 a 1 d h 3 I 1 l x / / / / /01 Draining Venting Extension dimen sion Allocation stub shaft/ drive lantern Contained in abbreviation v. page ,75 1, / S 1, / L 2, / L ,75 1, / S 1, / L 2, / L S 5,5 7, / ,75 1, / S 1, / L 2, / L S 5,5 7, / S 1, / L 2, / L S 5,5 7, / M L 2, / L S 5,5 7, / M L 18, VM 527 GB/05.06 Ident No
15 n = 2900/3500 1/min diameter at mm 30 Pump 25200/01 2/25200/ / /01 2/32200/ / / /01 2/40250/ /01 Motor Performance Flanges Pump dimensions Aggregate dimensions Motor dimensions approx. dimensions varying depending upon manufacturer kw DN S DN d a f a 2 b 1 b 2 f 1 h 1 h 2 a 1 d h 3 I 1 l x Extension dimen sion Allocation stub shaft/ drive lantern Contained in abbreviation v. page L S 5,5 7, / M S 5,5 7, / M L 18, L S 5,5 7, / M L S 5,5 7, / M L 18, M / S 5,5 7, / M L 18, M / L S 5,5 7, / M L 18, L S 5,5 7, / M L 18, M / S 5,5 7, / M L 18, M / M L 18, M / L S 5,5 7, / M L 18, M /350 VM 527 GB/05.06 Ident No
16 n = 2900/3500 1/min diameter at mm 30 Pump 50200/ /01 2/50250/ / / / / / /01 Motor Performance Flanges Pump dimensions Aggregate dimensions Motor dimensions approx. dimensions varying depending upon manufacturer kw DN S DN d a f a 2 b 1 b 2 f 1 h 1 h 2 a 1 d h 3 I 1 l x Extension dimension Allocation stub shaft/ drive lantern/ intermediate ring Contained in abbreviation v. page S 5,5 7, / M L 18, M / S 5,5 7, / M L 18, M / M L 18, M / S 5,5 7, / M L 18, M / S 5,5 7, / M L 18, M / L 18, M / S 5,5 7, / M L 18, M / M L 18, M / M L 18, M / The motor dimensions as indicated are approximate dimensions. Exact data depend on the motor make. When using special motors, make sure that other performances are allocated to the individual s, depending upon the enclosure. The main dimensions change accordingly. In case of order, binding tables of motor dimensions must be supplied to us. Subject to technical alterations. ALLWEILER AG Postfach Radolfzell Allweilerstr Radolfzell Germany Tel. +49 (0) Fax (0) service@allweiler.de Internet: VM 527 GB/05.06 Ident No
Norm-Centrifugal Pumps PN 10
Norm-Centrifugal Pumps PN 10 Pump dimensions acc. to DIN EN 733 with additional sizes Technical requirements acc. to DIN ISO 9908 Application For pumping pure water, industrial water, sea water, condensate,
More informationVolute Casing Centrifugal Pumps in In-line Design with Magnetic Drive. Series CNI-M
Volute Casing Centrifugal Pumps in In-line Design with Magnetic Drive Series CNI-M Usage For pumping toxic, volatile, explosive or other fluids harmful to the environment which call for service of hermetically
More informationVolute Casing Centrifugal Pumps in High Temperature Design with Magnetic Drive. Series CNH-ML
Volute Casing Centrifugal Pumps in High Temperature Design with Magnetic Drive Series CNH-ML Usage For pumping toxic, volatile, explosive or other fluids harmful to the environment which call for service
More informationVolute Casing Centrifugal Pumps PN 16 for Heat Transfer Oils up to 350 C Series NTT Pump dimensions acc. to DIN EN 733 with additional sizes
Volute Casing Centrifugal Pumps PN 16 for Heat Transfer Oils up to 350 C Series NTT Pump dimensions acc. to DIN EN 733 with additional sizes Application For handling organic heat-transfer oils in heat
More informationHigh-Pressure Centrifugal Pumps
High-Pressure Centrifugal Pumps L LV Application For handling fluids which do not contain any abrasive particles nor chemically attack the pump materials. Main fields of application In water supply, booster,
More informationVolute Casing Centrifugal Pumps according to EN 22858, ISO 2858 with Magnetic Drive. Series CNH-M
Volute Casing Centrifugal Pumps according to EN 22858, ISO 2858 with Magnetic Drive Series CNH-M Usage For pumping toxic, volatile, explosive or other fluids harmful to the environment which call for service
More informationVolute Casing Centrifugal Pumps of the Block-Type Construction with Magnetic Coupling
Volute Casing Centrifugal Pumps of the BlockType Construction with Magnetic Coupling ALLMAG Series CMA ATEX 0 a Application For handling toxic, volatile, explosive or other fluids harmful to the environment
More informationVolute Casing Centrifugal Pumps PN 16 for heat-transfer liquids Heat-transfer oil up to 350 C Hot water up to183 C
Volute Casing Centrifugal Pumps PN 16 for heat-transfer liquids Heat-transfer oil up to 350 C Hot water up to183 C Series CMIT in inline design Series CMAT with axial inlet ATEX 0 a Series CMAT Series
More informationPN 16/PN 25 Volute Centrifugal-Pumps for Heat Transfer Media Thermal Oil up to 400 C Hot Water up to 207 C
PN 16/PN 25 Volute Centrifugal-s for Heat Transfer Media Thermal Oil up to 00 C Hot Water up to 7 C Series NTWH/CTWH Series NBWH/CBWH Series NIWH/CIWH Application For circulating heat transfer media such
More informationSupply plus delivery pressure must not exceed the admissible internal pump pressure.
Vertical High-Pressure Centrifugal Pump Series CVP Application For handling pure water and condensates. The fluids to be pumped must not contain any abrasive particles nor chemically attack the pump materials.
More informationScrew Pumps Series SPF
Screw umps Application For the delivery of fuel oils, lube oils, hydraulic oils or other lubricating liquids. The fluid media must not contain any abrasive particles nor attack the pump materials chemically.
More informationPN 16 Volute Centrifugal Pumps (depending on materials up to PN 25) according to EN 22858/ISO 2858 and EN ISO 5199
PN 16 Volute Centrifugal Pumps (depending on materials up to PN 25) according to EN 22858/ISO 2858 and EN ISO 5199 Utilization Used to pump non-aggressive or aggressive liquids, cold or hot liquids, clean
More informationScrew Pumps Series EMTEC HIGH-TECH FOR EMULSION. 20 DQ axial branch with pipe thread. 140 D8.6 radial branch with SAE flange
Screw Pumps 20 DQ axial branch with pipe thread HIGH-TECH FOR EMULSION 140 D8.6 radial branch with SAE flange Application For handling good, medium or mal-lubricating, abrasive fluids in cooling lubricant
More informationScrew Pump Twin Aggregates Series SPZ/M MagDrive
Screw Pump Twin Aggregates Series SPZ/M MagDrive Application For the delivery of fuel oils, hydraulic oils or other lubricating liquids. The fluid media must not contain any abrasive particles nor attack
More informationALLWEILER. Block Macerators Series ABM Designs S and I. Design I with controller and seal water unit
Block Macerators Series ABM Designs S and I Design S Design I with controller and seal water unit Usage Macerators chop solids conveyed in liquids; materials like wood, textiles, plastics, paper, rubber,
More informationALLWEILER. Pressure-relief valves, indirectly pilot-controlled. Series DVI
Pressure-relief valves, indirectly pilot-controlled Series DVI Range of application The pressure-relief valves of Series DVI can be applied for maximum operating temperatures up to 150 C (higher temperatures
More informationBoiler Feed Booster Pump YNK. Type Series Booklet
YNK Type Series Booklet Legal information/copyright Type Series Booklet YNK All rights reserved. The contents provided herein must neither be distributed, copied, reproduced, edited or processed for any
More informationVolute Casing Pump additional sizes to those of ISO 2858/EN 22858
Volute Casing Pump additional sizes to those of ISO 2858/EN 22858 CBTA 150200...350400 + 2 additional sizes 100160 and 125200 TECHNICAL DATA Output: up to 2200 m 3 /h Delivery head: up to 160 m Speed:
More informationVolute Centrifugal Pumps PN 16 / PN 25 for Heat Transfer Media Thermal Oil up to 350 C Hot Water up to 204 C. Series NTWH/CTWH process model
Volute Centrifugal s PN 16 / PN 25 for Heat Transfer Meia Thermal Oil up to 350 C Hot Water up to 20 C Series NTWH/CTWH process moel Series NTWH/CTWH Series NBWH/CBWH block moel Series NIWH/CIWH in-line
More informationHigh-pressure pumps Series HP49
High-pressure pumps Series HP49 www.andritz.com/pumps General Description / Application Multi-stage high pressure pumps for water supply, irrigation and industrial applications, for hot and cold water
More informationNon-clogging Pump DBS TECHNICAL DATA. Output: up to 1200 m 3 /h
Non-clogging Pump DBS 3216...30040 TECHNICAL DATA Output: up to 1200 m 3 /h Delivery head: up to 100 m Speed: up to 3600 rpm depending of the pump size and material execution Medium temperature: max. 110
More informationHigh-pressure pumps Series HP45
High-pressure pumps Series HP45 www.andritz.com/pumps General Description / Application Multi-stage high pressure pumps for water supply, irrigation and industrial applications, for hot and cold water
More informationNTT CENTRIFUGAL PUMPS TO EN733 (DIN 24255) FOR HEAT TRANSFER OILS UP TO 350 C
FOR HEAT TRANSFER OILS UP TO 350 C WE HAVE ALL THE TICKS Version 1 - NTT: Rapid Allweiler Pumps Whilst all care has been taken to ensure the accuracy of the information contained in this brochure was correct
More informationEtaprime B Type Series Booklet
Self-priming Pump Etaprime B Type Series Booklet Legal information/copyright Type Series Booklet Etaprime B All rights reserved. The contents provided herein must neither be distributed, copied, reproduced,
More informationNon-clogging Pump DBS TECHNICAL DATA. Output: up to 1200 m 3 /h. depending of the pump size and material execution
Non-clogging Pump DBS 3216...30040 TECHNICAL DATA Output: up to 1200 m 3 /h Delivery head: up to 100 m Speed: Medium temperature: max. 110 C Casing pressure: Shaft sealing: up to 3600 rpm depending of
More informationSelf-priming Pump. Etaprime B. Type Series Booklet
Self-priming Pump Etaprime B Type Series Booklet Legal information/copyright Type Series Booklet Etaprime B All rights reserved. The contents provided herein must neither be distributed, copied, reproduced,
More informationPropeller Pump. Performance data Delivery flow Q up to m³/h Delivery head H up to 1,5 m Liquid temperature t up to 100 C Delivery branch
Propeller Pump Utilization and main fields of application For pumping sewage containing nitrate or activated sludge from the nitrification basin to the denitrification basin (recirculation). Further for
More informationVolute pumps for heat carrier oils up to 350 C. SIHI SuperNova ZTND TECHNICAL DATA. Temperature: max. 350 C Casing pressure: PN 16
Volute pumps for heat carrier oils up to 350 C SIHI SuperNova ZTND 032-125... 200-500 TECHNICAL DATA Output: Delivery head: Speed: max. 0 m³/h max. 95 m max. 3600 rpm Temperature: max. 350 C Casing pressure:
More informationThermoplastic Centrifugal Pump Type NMB-S
ASV Stübbe GmbH & Co. KG Hollwieser Straße 5 D-32602 Vlotho Fon +49 (0) 57 33.7 99-0 Fax +49 (0) 57 33.7 99-2 00 www.asv-stuebbe.de contact@asv-stuebbe.de Thermoplastic Centrifugal Pump Type NMB-S Suction
More informationEtaline MN. In-line Pumps
Type Series Booklet 1146.51/05--EN Etaline In-line Pumps Automation products available: Hyamaster hyatronic Fields of Application F Heating systems F Air-conditioning systems F Cooling circuits F Service
More informationChemical Motor Pump Unit BN
MB / General Pump BN-type motor pump units are normal-priming, singlestage, plastic centrifugal pumps in block design with horizontal axis. Their dimensions and flow rates mainly correspond to DIN/EN.
More informationVolute pumps for hot water
Volute pumps for hot water ZLI 25-125... 80-200 TECHNICAL DATA output: max. 140 m³/h delivery head: max. 60 m speed: max. 3600 1/min material: spheroidal graphite iron temperature: max. 150 C casing pressure:
More informationVolute pumps for heat carrier oils up to 350 C SIHI SuperNova ZTND 032-125... -500 TECHNICAL DATA Output: max. 0 m³/h Delivery head: max. 95 m Speed: max. 3600 rpm Temperature: max. 350 C Casing pressure:
More informationThe e-nsc End Suction Pump Series
NEW The e-nsc End Suction Pump Series Your go-to single-stage pump for heavy-duty use STANDARDIZED TO EN733, ISO 5199 AND DIRECTIVE 9/125/EC. POTABLE WATER APPROVED (ACS AND DM174). It s not your standard
More informationThermoplastic Centrifugal pump, Type NM
Thermoplastic Centrifugal pump, Type NM acc. to DIN 24256, EN 22858 and ISO 2858 Size: 32-125 up to 150-400 Capacity Q: up to 450 m 3 / h Head H: up to 100 m Operating temperature t: PE up to + 70 C PP
More informationSIHI SuperNova. Volute casing pumps. Type ZLIC TECHNICAL DATA. 0B, 0C, 4B max. 120 C Casing pressure: PN 16 / PN 10 1)
Volute casing pumps SIHI SuperNova Type ZLIC 040160... 200 TECHNICAL DATA Output: Head: Speed: Material: Temperature: max. 330 m³/h max. 60 m max. 3600 rpm grey cast iron: 0B, 0C material design: 0B, 0C,
More informationSide channel pumps ADH/CDH AEH TECHNICAL DATA. Temperature: max. 120 C. PN 40 for AEH
Side channel pumps ADH/CDH 0801... 2504 AEH 0805... 0808 TECHNICAL DATA Capacity: Head: Speed: max. 7,2 m³/h max. 400 m max. 3000 rpm Temperature: max. 120 C Casing pressure: Shaft sealing: PN 25 for ADH/CDH
More informationAxially split volute casing pumps. Applications. Bearings. Shaft seal. Operating data
Type series booklet 1385.52/3--10 RDLV Axially split volute casing pumps Applications Waterworks, irrigation and drainage pumping stations, power stations, industrial water supply systems, fire fighting
More informationData sheet. Page: 1 / 5. ETL GGSAV11D BKSBIE3 Inline pump. Operating data. Design
Data sheet Page: 1 / 5 Operating data Requested flow rate Operating data determined for maximum inlet pressure Requested developed head 15.00 m Pumped medium Ambient air temperature 20.0 C Fluid temperature
More informationILN, ILNC. In Line vertical pumps. ILN single suction ILN double suction ILNC. 1. Fields of Application. 3. Design. 4. Designation. 2.
Type series booklet CTI-2600/04 [04-2017] ILN, ILNC In Line vertical pumps ILN single suction ILN double suction ILNC sizes 65/ to 250/... sizes 300/ all sizes 1. Fields of Application Suitable for a wide
More informationTPED /4-A-F-A-BQQE 3X400 50HZ
GRUNDFOS DATA BOOKLET TPED 125-3/4-A-F-A-BQQE 3X4 5HZ Grundfos pump 98742617 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tped/98742617/tped-125-3-4-a-f-a-bqqe.html
More informationTechnical data 50 & 60 Hz. Vertical centrifugal pumps Series: DPLHS
Technical data 50 & 60 Hz Vertical centrifugal pumps Series: DPLHS 2 Table of Contents 1 Pump introduction 1.1 General... 4 1.2 Model key... 4 1.3 Description of the product... 4 1.4 Operation... 5 1.5
More informationNBE50-250/205 A-F2-A-BAQE
GRUNDFOS DATA BOOKLET NBE5-25/25 A-F2-A-BAQE Grundfos pump 9518635 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/nbe/9518635/nbe-5-25-25-a-f2-a-e-baqe.html
More informationVolute pumps for hot water up to 230 C
Volute pumps for hot water up to 230 C SIHI SuperNova ZEND 031125... 125250 TECHNICAL DATA Output: Delivery head: Speed: max. 600 m³/h max. 90 m max. 3600 rpm Temperature: max. 230 C (1) Casing pressure:
More informationType ZEND. SIHI Model: ZEND / ZDND / ZHND Hot Water Transfer Pumps Product Reference Manual. Experience In Motion. FPD-xxxx
Type ZEND SIHI Model: ZEND / ZDND / ZHND Hot Water Transfer Pumps Product Reference Manual FPD-xxxx Experience In Motion Volute pumps for hot water up to 230 C SIHI SuperNova ZEND 031125... 125250 TECHNICAL
More informationNB /263 AS-F2-A-BAQE
GRUNDFOS DATA BOOKLET NB125-25/263 AS-F2-A-BAQE Grundfos pump 9832195 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/nb/9832195/nb-125-25-263-as-f2-a-e-baqe.html
More informationALLWEILER. Pressure relief valves, directly controlled. Series DS/DT
ALLWEILER Pressure relief valves, directly controlled Range of application The pressure relief valves of can be applied for maximum operating temperatures up to 150 C (higher temperatures on request).
More informationContents. Identification
Contents Identification Type key Product data Introduction Applications Features and benefits Performance range pole pole Construction Sectional drawing Construction features Test pressure Operating conditions
More informationTP /2-A-F-A-BAQE 400D 50HZ
GRUNDFOS DATA BOOKLET TP 32-38/2-A-F-A-BAQE 4D 5HZ Grundfos Pump 968677 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tp/968677/tp-32-38-2-a-f-a-baqe.html
More informationVolute pumps for hot water up to 207 C
Volute pumps for hot water up to 207 C SIHI SuperNova ZDND 032160... 250 TECHNICAL DATA Output: Delivery head: Speed: max. 600 m³/h max. 90 m max. 3600 Temperature: max. 207 C Casing pressure: PN 25 Shaft
More informationTP /4-A-F-A-BQQE 400Y 50HZ
GRUNDFOS DATA BOOKLET TP 4-1/4-A-F-A-BQQE 4Y 5HZ Grundfos Pump 9686883 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tp/9686883/tp-4-1-4-a-f-a-bqqe.html
More informationData sheet. Page: 1 / 5 ETN GG A 11GA201502B. Operating data. Design. Requested developed head m. Efficiency 74.
Data sheet Page: 1 / 5 Operating data Requested flow rate 160.00 m³/h Actual flow rate 159.85 m³/h Operating data determined for maximum inlet pressure Actual developed head 20.96 m Requested developed
More informationThermoplastic Centrifugal Pump type NMB
ASV Stübbe GmbH & Co. KG Hollwieser Straße 5 D-32602 Vlotho Fon +49 (0) 57 33.7 99-0 Fax +49 (0) 57 33.7 99-2 00 www.asv-stuebbe.de contact@asv-stuebbe.de Thermoplastic Centrifugal Pump type NMB Suction
More informationTP /4-A-F-A-BUBE 400Y 50HZ
GRUNDFOS DATA BOOKLET TP 1-6/4-A-F-A-BUBE 4Y 5HZ Grundfos Pump 9642628 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tp/9642628/tp-1-6-4-a-f-a-bube.html
More informationScrew Pumps Series EMTEC. with ALLSPEED Controller HIGH-TECH FOR EMULSION. 20 DQ axial suction branch with pipe thread
Screw Pumps DQ axial suction branch with pipe thread with ALLSPEED Controller HIGH-TECH FOR EMULSION 1 D8.6 radial suction branch with SAE flange Applications For handling liquids with good, limited or
More informationNB /193 A-F2-A-BAQE
GRUNDFOS DATA BOOKLET NB100-200/193 A-F2-A-BAQE Grundfos Pump 98305367 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/nb000/98305367/nb-100-200-193-a-f2-a-e-baqe.html
More informationClose-coupled pumps Series ES04
Close-coupled pumps Series ES04 www.andritz.com/pumps General Description / Application Pumps of series ES04 are extremely compact units which require very little space. They are particularly suitable
More informationSeries PRODUCTS. self-priming Horizontal screw pump for non lubricating liquids. Water. Seawater. Heavy fuel oils. Bilge/Ballast pumps
self-priming Horizontal screw pump for non lubricating liquids PRODUCTS Water Seawater Oils Heavy fuel oils Light products Labelling Bilge/Ballast pumps General service pumps Cargo pumps Transfer pumps
More informationNBE40-125/139 AS-F2-A-BAQE
GRUNDFOS DATA BOOKLET NBE-125/139 AS-F2-A-BAQE Grundfos pump 999983 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/nbe/999983/nbe--125-139-as-f2-a-e-baqe.html
More informationLowara. Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733. SH Series. 60 Hz
Centrifugal Electric Pumps Manufactured in AISI 316 Stainless Steel in Compliance with EN 733 SH Series 60 Hz SERIE SH HYDRAULIC PERFORMANCE RANGE AT 60 Hz WEB 10-2006 2 CONTENTS 5 Specifications... 6
More informationSide channel pumps PN 16 SOH - SOHB. Self-priming centrifugal pumps. Technical description
Side channel pumps PN 16 Self-priming centrifugal pumps SOH - SOHB Technical description Operating data Design Industries Media pumped: Nominal diameter: 1-1 1 /2 Flow rate: 0.3-7.5 m 3 /h Pump head: 5-155
More informationTP /2-A-F-A-BUBE 1X230 50HZ
GRUNDFOS DATA BOOKLET TP 8-12/2-A-F-A-BUBE 1X23 5HZ Grundfos pump 9642448 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tp/9642448/tp-8-12-2-a-f-a-bube.html
More informationour contribution for environmental protection Sealless magnetic coupled centrifugal pumps acc. to EN Type NML / NMB
Sealless magnetic coupled centrifugal pumps acc. to EN 22858 our contribution for environmental protection Type NML / NMB General Magnetic coupled DICKOW-pumps of the series NM are sealless pumps. The
More informationTPE /4-A-F-A-BAQE 3X400 50HZ
GRUNDFOS DATA BOOKLET TPE 1-11/-A-F-A-BAQE 3X 5HZ Grundfos Pump 99113 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tpe/99113/tpe-1-11--a-f-a-baqe.html
More informationNB80-160/161 A-F2-A-BQQE
GRUNDFOS DATA BOOKLET NB8-16/161 A-F2-A-BQQE Grundfos pump 9943539 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/nbe/9943539/nbe-125-315-275-as-f2-a-e-bqqe.html
More informationTPE 25-80/2-A-O-A-BUBE 1X230 50HZ
GRUNDFOS DATA BOOKLET TPE 25-8/2-A-O-A-BUBE 1X23 5HZ Grundfos pump 98525643 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tpe/98525643/tpe-25-8-2-a-o-a-bube.html
More informationBearings. Shaft seal. Materials
Type series booklet 1385.51/3--10 RDL Axially split volute casing pumps Applications Waterworks, irrigation and drainage pumping stations, power stations, industrial water supply systems, fire fighting
More informationTPE N-A-F-I-BUBE
GRUNDFOS DATA BOOKLET TPE2 50-200-N-A-F-I-BUBE Grundfos pump 98416629 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tpe3ni/98416629/tpe2-50-200-n-a-f-i-bube.html
More informationMultistage Pumps MP, MPA, MPB, MPV SIZES DN 40 - DN 125. Jansen Pompentechniek T: +31(0) E:
Multistage Pumps MP, MPA, MPB, MPV SIZES DN 40 - DN 125 Technical Data Performance range: m Capacities up to 340m 3 /h (1500USgpm) m Head up to 500m (1640feet) m Max. speed up to 3600rpm Multistage pumps
More informationNB /438 A-F1-A-GQQE
GRUNDFOS DATA BOOKLET NB15-4/438 A-F1-A-GQQE Grundfos pump 983626 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/nb/983626/nb-15-4-438-a-f1-a-e-gqqe.html
More informationNK40-160/172A1F2AE-SBAQE
GRUNDFOS DATA BOOKLET NK4-16/172A1F2AE-SBAQE Grundfos pump 9782923 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/nkbasis/9782923/nk-4-16-172-a1-f-a-e-baqe.html
More informationSIHI LPH-X - Liquid Ring Vacuum Pump Two Stage
- Liquid Ring Vacuum Pump Two Stage 45008, 45311, 45316 Pressure Range: Suction Volume: 33 to 1013 mbar 55 to 258 m³/h CONSTRUCTION Sterling SIHI liquid ring vacuum pumps have a simple but robust construction
More informationTP /2-A-F-A-BQQE 400D 50HZ
GRUNDFOS DATA BOOKLET TP 65-46/2-A-F-A-BQQE 4D 5HZ Grundfos Pump 9687526 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tp/9687526/tp-65-46-2-a-f-a-bqqe.html
More informationChemical Magnetic Pumps with PTFE/PFA lining ATEX- and FDA compliant
Chemical Magnetic Pumps with PTFE/PFA lining ATEX- and FDA compliant Highly corrosionresistant pumps for absolute aggressive liquids and dangerous liquids. Energy-efficient pumps and chemical pumps Sustainable
More informationTPE /2-S-A-F-A-BAQE 3X400 50HZ
GRUNDFOS DATA BOOKLET TPE -33/2-S-A-F-A-BAQE 3X HZ Grundfos Pump 99116 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tpes2/99116/tpe--33-2-s-a-f-a-baqe.html
More informationCRE20-08 A-F-A-E-HQQE 3x HZ
GRUNDFOS DATA BOOKLET CRE2-8 A-F-A-E-HQQE 3x4 6 HZ Grundfos pump 96514642 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/cre2/96514642/cre-2-8-a-f-a-e-hqqe.html
More informationRDLO / RDLO V. Axially Split Volute Casing Pumps. Fields of Application. Bearings. Operating Data. Materials. Design. Shaft Seal. Designation 01 P F
Type Series Booklet 1387.5/2--10 RDLO / RDLO V Axially Split Volute Casing Pumps Fields of Application Waterworks, irrigation and drainage pumping stations, power stations, industrial water supply systems,
More informationXFLO XS SERIES. Single Stage Double Suction Split Casing Centrifugal Pump
XFLO P U M P S XS SERIES Single Stage Double Suction Split Casing Centrifugal Pump General and Construction 1. Applications Waterworks, Irrigation, Drainage pumping stations, Power stations, Industrial
More informationChemical pump with plastic liner in close-coupled design
Type series booklet 793.5/40 G3 TyachemBloc Chemical pump with plastic liner in closecoupled design Fields of Application TyachemBloc pumps are used for handling highly aggressive, corrosive and abrasive
More informationRWCP, RWCN. Vertical pumps for tanks for loaded liquids. 1. Fields of Application. 3. Design. 4. Designation. 2. Operating Data
Type series booklet CTI-4900/01 [04-2012] RWCP, RWCN Vertical pumps for tanks for loaded liquids 1. Fields of Application RWCP and RWCN are vertical, centrifugal pumps designed for wells, ditches and tanks.
More informationTP /2-A-F-A-BQQE 400D 50HZ
GRUNDFOS DATA BOOKLET TP 1-36/2-A-F-A-BQQE 4D 5HZ Grundfos pump 9619194 Thank you for your interest in our products. Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tp/9619194/tp-1-36-2-a-f-a-bqqe.html
More informationMultistage Pumps. Vogel Series P, PVa, MP 300
Multistage Pumps Vogel Series P, PVa, MP 300 Technical Data Performance range: m Capacities up to 1800m 3 /h (8800USgpm) m Head up to 300m (1000feet) m Max. speed up to 1750rpm Multistage pumps of series
More informationProgressive Cavity Pumps in Block Design TECFLOW Series
Progressive Cavity Pumps in Block Design TECFLOW Series Applications In waste water and waste water treatment engineering and in environmental industries for pumping low and high viscous liquids, neutral,
More informationHTM Circulation Pumps acc. to DIN EN 733 Type NKLs
HTM Circulation Pumps acc. to DIN EN 733 Type NKLs General The DICKOW standard HTM pumps, series NKLs according to EN 733, are designed as centrifugal pumps of light duty for handling heat transfer media.
More informationNK /310A2F1AE-SBAQE
GRUNDFOS DATA BOOKLET NK15-315/31A2F1AE-SBAQE Grundfos Pump 98318632 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/nkbasis/98318632/nk-15-315-31-a2-f-a-e-baqe.html
More informationTechnical Data 50 Hz. Vertical centrifugal pumps Series: DPVE / DPV(S) / DPVCF / DPLHS
Technical Data 50 Hz Vertical centrifugal pumps Series: DPVE / DPV(S) / DPVCF / DPLHS DPVE DPV(S) DPVCF DPLHS Table of Contents 1 Pump introduction 1.1 General... 5 1.2 Model key... 5 1.3 Description of
More informationMultistage Submerged Centrifugal Pump Type HZV
Multistage Submerged Centrifugal Pump Type HZV GENERAL, FIELD OF APPLICATION The DICKOW vertical submersible long shaft pump is a one or multistage centrifugal pump. The performance range covers capacities
More informationALLWEILER. Pressure relief valves, indirectly pilot controlled. Series DVI
Pressure relief valves, indirectly pilot controlled Series DVI Range of application The pressure relief valves of Series DVI can be applied for maximum operating temperatures up to 150 C (higher temperatures
More informationData sheet. Etaline GN /3002 G11 Version no.: 1 Inline pump. Operating data. Design. Clean water. Efficiency 61.6 % 20.0 C.
Data sheet Item no.: 1900 Page: 1 / 5 Operating data Pumped medium Water Actual flow rate 72.19 m ³/h Operating data determined for maximum inlet pressure Actual developed head 70.26 m Clean water Efficiency
More informationData sheet. Customer item no.: Communication dated: Number: ES Doc. no.: Item no.: 100 Quantity: 1 Date: 19/03/2015 Page: 1 / 6
Data sheet Item no.: Page: 1 / 6 Operating data Operating data determined for maximum inlet pressure Pumped medium Water Clean water Not containing chemical and mechanical substances which affect the materials
More informationChemical Pumps. With mechanical seal. Non-Metallic Standardized Chemical Pump Type NP. In PP / PE-UHMW / PVDF Dimensions to EN / ISO 2858
Chemical Pumps With mechanical seal Non-Metallic Standardized Chemical Pump Type NP In PP / PE-UHMW / PVDF Dimensions to EN 22 / ISO 2 Applications Type NP standardized chemical pumps are the solution
More informationLowara. Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733. SH Series. 50 Hz
Centrifugal electric pumps made of AISI 316 stainless steel in compliance with EN 733 SH Series 50 Hz SERIE SH OPERATING CHARACTERISTICS AT 50 Hz PRINT 05-2007 2 CONTENTS 5 Specifications......................................................................
More informationWaste Water, Condensate and Heat Transfer Fluid Pump. Type Series Booklet
Waste Water, Condensate and Heat Transfer Fluid Pump Type Series Booklet Legal information/copyright Type Series Booklet All rights reserved. The contents provided herein must neither be distributed, copied,
More informationTPED /4-S-A-F-A-BAQE 3X400 50HZ
GRUNDFOS DATA BOOKLET TPED -9/-S-A-F-A-BAQE 3X 5HZ Grundfos Pump 99137 Thank you for your interest in our products Please contact us for more information, or visit our website https://www.lenntech.com/grundfos/tpeds/99137/tped--9--s-a-f-a-baqe.html
More informationSCHMITT. product information. Kreiselpumpen. U Pump Series. normal priming, centrifugal pumps with a single mechanical seal.
SCHMITT Kreiselpumpen chemical resistant pumps for corrosive and highly pure media product information U Pump Series normal priming, centrifugal pumps with a single mechanical seal materials: PVDF Description
More informationSide channel pumps PN 16 SOH - SOHB - SOHM. Self-priming centrifugal pumps. Technical description
Side channel pumps PN 16 Self-priming centrifugal pumps SOH - SOHB - SOHM Technical description ATEX certified The SOH side channel pump models are available in a variety of designs. Design base plate
More informationDouble Mechanical Seals
Double Mechanical Seals Back-to-back Arrangement With Seal Supply System Supplementary Operating Manual Legal information/copyright Supplementary Operating Manual Double Mechanical Seals Original operating
More informationTOE-GN / GA / GI Series. Heat transfer pumps for heat transfer oils up to 350 C and hot water up to 160 C
TOE-GN / GA / GI Series Heat transfer pumps for heat transfer oils up to 350 C and hot water up to 160 C with uncooled mechanical seals volute casing PN 16 bearing brackets 360 and 470 2 Pumps for heat
More informationSIHI LPH-X - Liquid Ring Vacuum Pump Two Stage
- Liquid Ring Vacuum Pump Two Stage LPH 45008, LPH 45311, LPH 45316 Pressure Range: Suction Volume: 33 to 1013 mbar 55 to 258 m³/h CONSTRUCTION Sterling SIHI liquid ring vacuum pumps have a simple but
More informationTOE-MN / MA / MI Series. Heat transfer pumps for heat transfer oils up to 350 C
TOE-MN / MA / MI Series Heat transfer pumps for heat transfer oils up to 350 C with magnetic coupling volute casing PN 16 bearing brackets 360 and 470 2 Pumps for heat transfer technology Main applications
More information