SAFE - ANSI. Angle pattern safety valve 1 to 6 (DN 25 to 150) Safety valves ARI-SAFE-ANSI
|
|
|
- Phillip Green
- 5 years ago
- Views:
Transcription
1 SAFE - ANSI Safety valves Angle pattern safety valve 1 to 6 (DN 25 to 150) ARI-SAFE-ANSI ASME Code Section VIII-Division 1. UV-stamp NB-stamp Type-test approved acc. to TRD and AD2000-A2 Direct loaded with spring: TÜV SV D/G Figure TÜV SV F Figure 901/911 Further approvals: see inside Fig Page 2 Fig. 900 Features: Direct loaded with spring Wear resistant seat/disc Precision disc alignment and guide Possible with soft seal disc Possible with EPDM bellow Possible with stainless steel bellow Edition 01/05 - Data subject to alteration Data sheet
2 SAFE - ANSI ANSI - safety valve Fig closed lifting device Fig open lifting device Fig gastight cap Fig open lifting device Registration Figure Pressure class Material Nominal diameter Temperature range Flanges ASME Code Section VIII-Division EN ISO , VdTÜV-100, AD2000-A2,TRD ANSI 150 / 150 ANSI 300 / 150 SA 216 WCB 1 x2 up to 6 x10-20 F up to +800 F - 29 C up to +427 C ASME B16.5 Requirement ASME Code Section VIII-Division 1. EN ISO , VdTÜV-leaflet 100, AD2000-A2,TRD 421 Marking UV-stamp NB-stamp BKZ TÜV SV D/G TÜV SV F Application neutral gases, vapours and liquids steam, neutral gases, vapours and liquids Construction Safety valve, spring loaded, direct loaded Sizing Calculation acc. to ASME Calculation acc. to EN ISO , AD2000-A2, TRD 421 Medium gasform: Medium liquid: Order data: Mass flow (lb/h), SCFM, molar mass (kg/kmol), temperature ( F), set gauge pressure (psig), back gauge pressure (psig) Volume flow (gal/min), density, viscosity, temperature ( F), set gauge pressure (psig), back gauge pressure (psig) ARI-SAFE-ANSI-safety valve - Figure..., Nominal diameter..., Class..., Material..., set gauge pressure... psig Mass flow (kg/h), molar mass (kg/kmol), temperature ( C), set gauge pressure (bar), back gauge pressure (bar) Mass flow (kg/h), density (kg/m3), viscosity, temperature ( C), set gauge pressure (bar), back gauge pressure (bar) ARI-SAFE-ANSI-safety valve - Figure..., DN... /..., PN.. /.., Material..., set gauge pressure... bar Nominal diameter 1 x 2 1 1/2 x 2 11/2 x 2 1/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 Orifice letter D/E F G H (H) J (K) L (L) M (N) P Q R Weight (lbs) Weight (kg) Weight, bellow design (lbs) Weight, bellow design (kg) 13, , without metal bellow with metal bellow static back pressure no backpressure allowed on request dynamic back pressure max. 10% from set pressure (gauge) (higher on request) on request 2 Edition 06/04 - Data subject to alteration
3 Calculation acc. to ASME Capacity saturated steam / air incl. 10% overpressure 1) SAFE - ANSI Fig. 901 / 902 / 911 / 912 Set gaugepressure I Saturated steam lb/hr (pounds per hour) II Air scfm (60 F; 14,7 psia) (standard cubic feet per minute) psig 1 x 2 1 1/2 x 2 11/2 x 2 1/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 orifice D/E F G H (H) J (K) L (L) M (N) P Q R letter I II I II I II I II I II I II I II I II I II I II ) Capacities below 30 psig set pressure are calculated at 3 psig overpressure. Spring ranges in psig 1 x 2 1 1/2 x 2 11/2 x 2 1/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 6 x 8 6 x Edition 09/02 - Data subject to alteration 3
4 Calculation acc. to ASME Capacity water incl. 10% overpressure 1) SAFE - ANSI Fig. 901 / 911 Set gaugepressure Water gal/min (U.S. Gallons per minute) psig 1 x 2 1 1/2 x 2 11/2 x 21/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 orifice letter D/E F G H (H) J (K) L (L) M (N) P Q R ) Capacities below 30 psig set pressure are calculated at 3 psig overpressure. Stainless steel-bellow: Spring ranges in psig 11/2 x 2 1 x 2 11/2 x 21/2 1 1/2 x 3 2 x 3 3 x 4 4 x Design with bellow as standard valve (only Fig. 901/911) 4 Edition 02/03 - Data subject to alteration
5 Calculation acc. to ASME (SI-units) Capacity saturated steam / air incl. 10% overpressure SAFE - ANSI Fig. 901 / 902 / 911 / 912 Set gaugepressure I Saturated steam kg/h II Air in Nm 3 /h (16 C; 1,013 bara) bar 1 x 2 1 1/2 x 2 11/2 x 2 1/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 orifice D/E F G H (H) J (K) L (L) M (N) P Q R letter I II I II I II I II I II I II I II I II I II I II 1 1, , , , Edition 09/02 - Data subject to alteration 5
6 Calculation acc. to ASME (SI-units) Capacity water incl. 10% overpressure SAFE - ANSI Fig. 901 / 911 Set gaugepressure Water in m 3 /h bar 1 x 2 1 1/2 x 2 11/2 x 21/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 orifice letter D/E F G H (H) J (K) L (L) M (N) P Q R , , , , Edition 08/02 - Data subject to alteration
7 Calculation acc. to TRD 421 and AD-leaflet A2 Capacity saturated steam / air incl. 10% overpressure SAFE - ANSI Fig. 901 / 902 / 911 / 912 Set gaugepressure I Saturated steam kg/h II Air in Nm 3 /h (0 C; 1,013 bara) bar 1 x 2 1 1/2 x 2 11/2 x 2 1/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 orifice D/E F G H (H) J (K) L (L) M (N) P Q R letter I II I II I II I II I II I II I II I II I II I II 0, , , , , , , TÜV SV D/G 40 Spring ranges in bar (gauge) 1 x 2 1 1/2 x 2 11/2 x 2 1/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 6 x 8 6 x 10 0,2-0,5 0,2-0,5 0,2-0,5 0,2-0,5 0,2-0,5 0,2-0,5 0,2-0,4 0,2-0,5 0,52-1 0,52-1 0,52-1 0,52-1 0,52-1 0,52-1 0,42-0,75 0,52-1 1,05-1,5 1,05-1,5 1,05-1,5 1,05-1,5 1,05-1,5 1,05-1,5 0,77-1,1 1,05-1,5 1,55-2 1,55-2 1,55-2 1,55-2 1,55-2 1,55-2 1,15-1,5 1,55-1,9 2,05-2,7 2,05-2,7 2,05-2,7 2,05-2,7 2,05-2,7 2,05-2,7 1,55-1,9 1,95-2,3 2,75-3,6 2,75-3,6 2,75-3,6 2,75-3,6 2,75-3,6 2,55-3 1,95-2,5 2,35-2,7 3,7-5 3,7-5 3,7-5 3,7-5 3,7-5 3,05-3,6 2,55-2,95 2,75-3,3 5,1-9 5,1-9 5,1-9 5,1-9 5,1-9 3, ,35-4,1 9,1-16 9,1-16 9,1-16 9,1-16 9,1-16 5,1-9 4,1-5,7 4,2-5,5 16, , , , ,1-22 9,1-14 5,8-8,2 5,6-7,4 22, , , , , ,1-19 8,3-12 7, , , , , , , , , , , ,1-26 Edition 02/03 - Data subject to alteration 7
8 Calculation acc. to TRD 421 and AD-leaflet A2 Capacity water incl. 10% overpressure SAFE - ANSI Fig. 901 / 911 Set gaugepressure Water in m 3 /h (20 C) bar 1 x 2 1 1/2 x 2 11/2 x 21/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 orifice letter D/E F G H (H) J (K) L (L) M (N) P Q R 0,2 5,13 8,53 8,53 13,1 20,5 30,8 73,0 73,0 94,9 132,0 0,5 8,12 13,5 13,5 20,8 32,5 48,8 115,0 115,0 150,0 209,0 1 11,5 19,1 19,1 29,4 45,9 69,0 163,0 163,0 212,0 295,0 2 16,2 27,0 27,0 41,6 64,9 97,5 231,0 231,0 300,0 417,0 3 19,9 33,0 33,0 50,9 79,5 119,0 283,0 283,0 368,0 511,0 4 22,9 38,1 38,1 58,7 91,8 138,0 326,0 326,0 424,0 590,0 5 25,7 42,6 42,6 65,5 102,0 154,0 365,0 365,0 474,0 660,0 6 28,1 46,7 46,7 72,0 112,0 169,0 400,0 400,0 520,0 723,0 7 30,4 50,4 50,4 77,7 121,0 182,0 432,0 432,0 562,0 781,0 8 32,5 53,9 53,9 83,1 130,0 195,0 461,0 461,0 600,0 835,0 9 34,4 57,2 57,2 88,1 138,0 207,0 490,0 490,0 637,0 885, ,3 60,3 60,3 92,9 145,0 218,0 516,0 516,0 671,0 933, ,0 63,2 63,2 97,4 152,0 229,0 540,0 540,0 703,0 977, ,7 66,0 66,0 102,0 159,0 239,0 565,0 565,0 735,0 1022, ,4 68,7 68,7 106,0 165,0 249,0 587,0 587,0 764,0 1062, ,9 71,3 71,3 110,0 172,0 258,0 611,0 611,0 794,0 1104, ,9 76,3 76,3 117,0 184,0 276,0 653,0 653,0 849,0 1181, ,7 80,9 80,9 125,0 195,0 293,0 692,0 692,0 900,0 1252, ,9 82,9 82,9 128,0 200,0 300,0 710,0 710,0 923,0 1284, ,3 85,3 85,3 131,0 205,0 308,0 730,0 730,0 949,0 1320, ,6 87,4 87,4 135,0 210,0 316,0 748,0 748,0 973,0 1350, ,2 93,4 93,4 144,0 225,0 338,0 800,0 800,0 1040,0 1443, ,4 95,3 95,3 147,0 229,0 345,0 1059,0 1473, ,5 97,2 97,2 150,0 234,0 352,0 1080,0 1502, ,6 99,0 99,0 153,0 238,0 358,0 1100, ,7 101,0 101,0 155,0 243,0 365, ,9 104,0 104,0 161,0 251, ,8 108,0 108,0 166,0 259, ,9 111,0 111,0 171,0 268,0 Stainless steel-bellow: Spring ranges in bar (gauge) 11/2 x 2 1 x 2 11/2 x 21/ /2 x 3 2 x 3 3 x 4 4 x 6 2,5-3,3 2,5-3,2 2,6-3,6 2,8-3,4 2,5-3,7 2,5-3,5 3,4-4,6 3,3-4,0 3,7-4,5 3,5-4,5 3,8-4,6 3,6-4,2 4,7-5,4 4,1-5,5 4,6-5,6 4,6-8,4 4,7-5,9 4,3-4,9 5,5-7,0 5,6-6,4 5,7-7,5 8,5-10,0 6,0-8,0 5,0-5,6 7,1-9,0 6,5-7,9 7,6-10,0 10,1-11,5 8,1-10,0 5,7-7,0 9,1-11,7 8,0-11,5 10,1-12,5 11,6-16,0 10,1-18,0 7,1-8,0 11,8-16,0 11,6-18,5 12,6-16,0 16,1-18,5 8,1-9,3 16,1-22,0 18,6-25,0 16,1-22,0 18,6-23,0 9,4-11,5 22,1-30,0 11,6-13,0 Design with bellow as standard valve (only Fig. 901/911) Edition 09/03 - Data subject to alteration
9 SAFE - ANSI Edition 04/02 - Data subject to alteration 9
10 10 Edition 06/04 - Data subject to alteration
11 SAFE - ANSI Safety valve-approvals Safety valveapprovals ASME Code Section VIII-Division 1 UV-stamp NB-stamp USA Canada Registration - CRN (only version with UV-stamp) VdTÜV - Germany (only version without UV-stamp) Pressure Equipment Directive 97/23/EG (PED) SAFE BR 900 Fig X X X X Edition 04/03 - Data subject to alteration 11
12 SAFE - ANSI Parts Pos. Description Material, Material-No. 1 Body SA 216 WCB 2 Seat SA 479 Gr.316 Ti 3 Stud SA 193 B7 4 Spindle guide DN 2 : AISI 420 DN > 2 : SA 395 / AISI Hexagon nut SA 194 2H 11 Bonnet, closed SA Disc unit AISI Spindle AISI Adjusting screw AISI Cap, closed SA Cap, open SA Cap, gastight SA Lift fork SA Lifting lever, closed SA Spring AISI 9254, AISI Lever, open SA Bonnet, open SA Bellow EPDM 55 Bellow unit SA 240 Gr. 316 Ti / SA 479 Gr. 316 Ti 70 Balanced piston SA 240 Gr. 316 Ti Pressure-temperature-ratings Temperature F -20 up to ANSI 150 Operating press. psig Temperature C -29 up to Operating press. bar 19,6 17,9 15,8 13,8 11,7 9,6 8,6 7,6 6,6 5,5 Temperature F -20 up to ANSI 300 Operating press. psig Temperature C -29 up to Operating press. bar 51,1 46,6 45,2 43,6 41,4 39,2 37,9 36,6 34,8 28,8 Intermediate values for max. permissible operational pressures can be determined by linear interpolation of the given temperature / pressure chart. Information / Restrictions of technical rules to be observed! A production allowance acc. to TRB 801 No. 45 exists. The engineer, designing a system or a plant, is responsible for the selection of the correct valve. Edition 01/05 - Data subject to alteration 12
13 SAFE - ANSI Dimensions in inch and mm SAFE-ANSI Figure Nominal diameter 1 x 2 1 1/2 x 2 11/2 x21/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 inch do 0,88 1,14 1,14 1,42 1,77 2,30 3,54 3,54 4,17 4,92 D1 ANSI 150 4, , ANSI 300 4,88 6,12 6,12 6,12 6,5 8, ,5 12,5 D2 ANSI ,5 7, ,5 16 b1 ANSI 300/150 0,69 0,81 0,81 0,81 0,88 1,12 1,25 1,44 1,44 b2 ANSI 150 0,75 0,75 0,88 0,94 0,94 0,94 1 1,12 1,19 l 4 1/2 4 3/4 4 3/4 4 7/8 4 7/8 6 1/2 7 1/ /2 10 1/2 l1 4 1/8 4 7/8 4 7/8 5 1/8 5 3/8 6 1/ /8 9 7/16 9 7/16 H , , ,3 35 H bellow design 13,2 15,4 15,4 17,5 19,7 24,4 30,3 30,3 36,2 37 X Center to face dimensions acc. to API 526 Flange dimensions acc. to ASME / ANSI B16.5 Nominal diameter 1 x 2 1 1/2 x 2 11/2 x21/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 API-orifice letter D E F G H (H) J (K) L (L) M (N) P Q R inch do 0,886 1,142 1,142 1,417 1,772 2,303 3,543 3,543 4,173 4,921 Ao (inch 2 ) 0,617 1,024 1,024 1,578 2,465 4,166 9,861 9,861 13,678 19,022 Flange dimension Nominal diameter 1 1 1/ / ANSI K (inch) 3,12 3,88 4,75 5,5 6 7,5 9,5 11,75 14, n x d (inch) 4 x 0,62 4 x 0,62 4 x 0,75 4 x 0,75 4 x 0,75 8 x 0,75 8 x 0,88 8 x 0,88 12 x 1 ANSI 300 K (inch) ,62 7,88 10, n x d (inch) 4 x x x x x x Nominal diameter 1 x 2 1 1/2 x 2 11/2 x21/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 mm do 22, , D1 ANSI ANSI D2 ANSI b1 ANSI 300/150 17,5 20,6 20,6 20,6 22,3 28,6 31,8 36,5 36,5 b2 ANSI ,1 19,1 22,3 23,8 23,8 23,8 25,4 28,6 30,2 l 114,3 120,7 120,7 123,8 123,8 165,1 184,2 228,6 241,3 266,7 l1 104,8 123,8 123,8 130,2 136,5 155,6 177, ,7 239,7 H H bellow design X Center to face dimensions acc. to API 526 Flange dimensions acc. to ASME / ANSI B16.5 Nominal diameter 1 x 2 1 1/2 x 2 11/2 x21/2 1 1/2 x 3 2 x 3 3 x 4 4 x 6 4 x 6 6 x 8 6 x 10 API-orifice letter D E F G H (H) J (K) L (L) M (N) P Q R mm do 22, , Ao (mm 2 ) Flange dimension Nominal diameter 1 1 1/ / ANSI K (mm) , ,5 190,5 241,5 298, n x d (mm) 4 x 16 4 x 16 4 x 19 4 x 19 4 x 19 8 x 19 8 x 22 8 x x 25 ANSI 300 K (mm) , n x d (mm) 4 x 19 4 x 22 8 x x 22 8 x x Edition 04/03 - Data subject to alteration 13
14 SAFE - ANSI Special designs EPDM Viton (FPM) Neoprene (CR) -31 F up to +302 F / -35 C up to +150 C Abbreviation E -13 F up to +356 F / -25 C up to +180 C Abbreviation V -22 F up to +257 F / -30 C up to +125 C Abbreviation N Bellow - stainless steel EPDM bellow (max F / +120 C) Metal seal Soft sealing disc Balanced stainless steel-bellow with balanced piston (Only for closed version!) Body material Nominal diameter A B S H 2 x /4 9/16 7/16 5 5/8 SA 216 WCB 3 x 4 8 3/8 3 1/2 3/4 9/16 6 3/8 4 x /8 6 1/2 7/8 5/8 7 5/16 6 x /2 7 1/4 7/8 13/16 9 3/4 6 x /8 7 7/8 7/8 13/16 9 7/8 Proximity switch Support tongues Lock bushing Test gag Rupture disc Heating jacket Seat SA 479 Gr.316 Ti / Stellite No. 21 Disc SA 479 Gr.316 Ti / Stellite No. 6 and removable lifting aid Removable lifting aid Chemical-version SA 479 Gr.316 Ti Technology for the future. GERMAN QUALITY VALVES ARI-Armaturen Albert Richter GmbH & Co. KG, D Schloß Holte-Stukenbrock, Tel / 994-0, Telefax / or 159 Internet: info.vertrieb@ari-armaturen.com 14 Edition 06/04 - Data subject to alteration
SAFE - ANSI / -TC / -TCP / -TCS
SAFE - ANSI / -TC / -TCP / -TCS Safety valves Angle pattern safety valve 1 to 6 ARI-SAFE-ANSI ASME Code Section VIII-Division 1. UV-stamp NB-stamp Type-test approved acc. to TRD and AD2000-A2 Direct loaded
Fig Page 2. Fig Page 10. Fig Page 14. Fig Page 16. Fig Page 20
SAFE Safety valves ARI-SAFE - Full lift- / Standard - safety valve ARI-SAFE Full lift safety valve D/G Standard safety valve F Type-test approved acc. to TRD and AD2000-A2 Direct loaded with spring: TÜV
Fig Page 2. Fig Page 6. Fig Page 10. Fig Page 14. Fig Page 16
SAFE Safety valves ARI-SAFE - Full lift- / Standard - safety valve ARI-SAFE Full lift safety valve D/G Standard safety valve F Type-test approved acc. to TRD and AD-A2 Direct loaded with spring: TÜV SV..
ARI-FABA -ANSI LongLife Stop valve with bellows seal
Stop valve with bellows seal Free of maintenance stop valve with bellows seal - metallic sealing ARI-FABA -ANSI LongLife - Class 150 Straight through with flanges German TA - Luft TÜV-Test-No. 088-945053
ARI-STEVI 470 / ANSI (DN25-200)
With pneumatic and electric actuators Control valve - straight through with screwed seat ring, shaftguided plug and blow-out protected stem ARI-STEVI 470 / 471 - ANSI Pneumatic actuator ARI-DP 32-35 Reversible
with pneumatic actuator Pneumatic process valve, Y-pattern DN ARI-STEVI AS 350 Pneumatic actuator - with screwed sockets
with pneumatic actuator Pneumatic process valve, Y-pattern DN 15-50 ARI-STEVI AS 350 - with screwed sockets Piston actuator Required air supply pressure, max. 10 bar Operating pressure, max. 16 bar Page
ARI-STEVI ANSI (NPS 1/2" - 2") with electric and pneumatic actuators Control valve in straightway form
with electric and pneumatic actuators Control valve in straightway form ARI-STEVI 440 - ANSI Pneumatic actuator ARI-DP 32-33 Reversible pneumatic actuator Actuator with rolling diaphragm Air supply pressure
Cast iron Nodular iron Cast steel BR 050 Page 2. Stainless steel BR 059 Page 2. Cast steel BR 080 Page 3
Strainer ARI-Strainer ARI-Strainer Y-pattern with flanges TRB 801 No. 45 (except GG-25) Cast iron Nodular iron Cast steel BR 050 Page 2 ARI-Strainer Y-pattern with flanges TRB 801 No. 45 Stainless steel
Strainer. ARI-Strainer. ARI-Strainer Y-pattern with flanges. ARI-Strainer Y-pattern with flanges. ARI-Strainer Y-pattern with butt weld ends
Strainer ARI-Strainer ARI-Strainer Y-pattern with flanges German "TA-Luft" TÜV-Test-No. 922-9204866 TRB 801 No. 45 (except cast iron) Cast iron Nodular iron Cast steel BR 050 Page 2 ARI-Strainer Y-pattern
ARI-FABA -Plus / -Supra ANSI Stop valve with bellows seal Free of maintenance stop valve with bellow seal - metallic sealing
ARI-FABA -Plus / -Supra ANSI Stop valve with bellows seal Free of maintenance stop valve with bellow seal - metallic sealing ARI-FABA -Plus ANSI Class 150 / Class 300 Straight through with flanges EN ISO
ARI-FABA -Plus / -Supra ANSI Stop valve with bellows seal Free of maintenance stop valve with bellow seal - metallic sealing
ARI-FABA -Plus / -Supra ANSI Stop valve with bellows seal Free of maintenance stop valve with bellow seal - metallic sealing ARI-FABA -Plus ANSI Class 150 / Class 300 Straight through with flanges EN ISO
-ANSI. maintenance-free. Stop valve with bellows seal,
Stop valve with bellow seal -ANSI ARI-FABA Long Life - Stop valve with bellows seal, maintenance-free ARI-FABA -ANSI Long Life Class 150 with flanges TA-Air (zero emission) TÜV-Test-No. 088-945053 Cast
with electric and pneumatic actuators Stop valve in straightway form DN ARI-STEVI 405 / 460 Electric actuator AUMA SA with LE
with electric and pneumatic actuators Stop valve in straightway form DN 300-500 ARI-STEVI 405 / 460 Electric actuator AUMA SA with LE Electric multiturn actuator capable of high closing pressures Enclosure
ARI-STEVI 450 / 451 (DN15-150) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring)
With pneumatic and electric actuators ARI-STEVI 450 / 451 (DN15-150) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring) ARI-STEVI 450 / 451 Pneumatic actuator ARI-DP
ARI-STEVI 450 / 451 Pneumatic actuator ARI-DP 32-34T. Electric actuator ARI-PREMIO 2,2-25 kn ARI-PREMIO-Plus 2G 2,2-25 kn
ARI-STEVI 450 / 451 (DN15-150) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring) With pneumatic and electric actuators ARI-STEVI 450 / 451 Pneumatic actuator ARI-DP
ARI-FABA -Plus / -Supra ANSI Stop valve with bellows seal
ARI-FABA -Plus / -Supra ANSI Stop valve with bellows seal Free of maintenance stop valve with bellows seal - metallic sealing ARI-FABA -Plus ANSI Class 150 / Class 300 Straight through with flanges TA
ARI-STEVI 448 / 449 (DN15-100) Control valve in straightway form with screwed seat ring With pneumatic and electric actuators
ARI-STEVI 8 / 9 (DN5-00) Control valve in straightway form with screwed seat ring With pneumatic and electric actuators ARI-STEVI 8 / 9 Pneumatic actuator ARI-DP 30-3 Reversible pneumatic actuator Actuator
ARI-STEVI 450 / 451 (DN15-150) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring)
With pneumatic and electric actuators Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring) ARI-STEVI 450 / 451 Pneumatic actuator ARI-DP 32-34T Reversible pneumatic actuator
with electric actuators Feedwater control valve with pump spill back DN
ARI-STEVI 453 with electric actuators Feedwater control valve with pump spill back DN 25-100 ARI-STEVI 453 Electric actuator ARI-PREMIO 2,2-15 kn ARI-PREMIO-Plus 2G 2,2-15 kn Enclosure IP 65 2 torque switches
ARI-STEVI 470 / 471 (DN15-150)
With pneumatic and electric actuators ARI-STEVI 470 / 47 (DN5-50) Control valve - straight through with screwed seat ring, shaftguided plug and blow-out protected stem ARI-STEVI 470 / 47 Pneumatic actuator
ARI-STEVI 470 / ANSI (DN25-200)
ARI-STEVI 470 / 471 - ANSI (DN25-200) Control valve - straight through with screwed seat ring, shaftguided plug and blow-out protected stem With pneumatic and electric actuators ARI-STEVI 470 / 471 - ANSI
ARI-Strainer PN63-160
ARI-Strainer PN63-160 ARI-Strainer - Screen of stainless steel DN 10-100 ARI-Strainer - Straight through with flanges TRB 801 Annex II No. 45 Cast steel Forged steel High temp. Steel Fig. 050 Page 2 +
ARI-Strainer. ARI-Strainer - Screen and supporting basket made of stainless steel. ARI-Strainer - Y-pattern with flanges
ARI-Strainer ARI-Strainer - Screen and supporting basket made of stainless steel ARI-Strainer - Y-pattern with flanges TRB 801 Annex II No. 45 (except EN-JL1040) EN ISO 15848-1 / TA - Luft TÜV-Test-No.
3-way control valve in mixing and diverting design
with electric and pneumatic actuators 3-way control valve in mixing and diverting design 1/2-6 STEVI 450 / 451 Electric actuator Enclosure IP 65 2 torque switches 1 travel switch Handwheel Additional devices
Forged steel High temperature steel Stainless steel BR 640 / BR 641 (Y) Page 2. with system connectors. Stainless steel BR 642 / BR 643 (Y) Page 4
Thermodynamic steam traps TRACO CONA TD Thermodynamic steam trap PN40 - with flanges (BR 640/641...1) - with screwed sockets (BR 640/641...2) - with socket weld ends (BR 640/641...3) - with butt weld ends
ARI-STEVI 423 / 463 Pneumatic actuator ARI-DP 34-34T. Electric actuator ARI-PREMIO 5-25 kn ARI-PREMIO-Plus 2G 5-25 kn
Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring) With pneumatic and electric actuators ARI-STEVI 423 / 463 Pneumatic actuator ARI-DP 34-34T Reversible pneumatic actuator
ARI-Strainer. Strainer - Screen and supporting basket made of stainless steel. ARI-Strainer - Y-pattern with flanges
Strainer - Screen and supporting basket made of stainless steel ARI-Strainer - Y-pattern with flanges TRB 801 Annex II No. 45 (except EN-JL1040) German TA - Luft TÜV-Test-No. 922-9204866 Grey cast iron
STEVI 450 / way control valve in mixing and diverting design DN
STEVI 450 / 451 with electric and pneumatic actuators 3-way control valve in mixing and diverting design DN 15-150 STEVI 450 / 451 Electric actuator ARI-PREMIO Enclosure IP 65 2 torque switches 1 travel
with electric and pneumatic actuators Control valve straight through with V-port plug DN ARI-STEVI 425 / 426
with electric and pneumatic actuators Control valve straight through with V-port plug DN 300-500 ARI-STEVI 425 / 426 Electric actuator AUMA SAR with LE Electric multiturn actuator capable of high closing
STEVI 440 / 441. Straight through control valve DN
with electric and pneumatic actuators Straight through control valve DN 15-100 Electric actuator ARI-PREMIO Enclosure IP 65 2 torque switches 1 travel switch Handwheel Additional devices available, e.g.
ARI-ZETRIX ANSI. with worm gear. with electric rotary actuator Auma or Schiebel. with pneumatic actuator. with hydraulic actuator
Process valve - Fig. 016 - Double flanged process valve with metallic sealing - Triple offset - Fig. 018 - Fully lugged process valve with metallic sealing - Triple offset - Fig. 019 - Butt weld ended
Type 455, 456. Type 455, 456. Flanged Safety Relief Valves spring loaded
Type 455, 456 Flanged Safety Relief Valves spring loaded Contents Chapter/Page Type 456 Packed lever H4 Closed bonnet Materials 08/02 Balanced bellows design 08/04 How to order Numbering system 08/06 Article
ARI-FABA -Plus Stop valve with bellows seal
Stop valve with bellows seal Free of maintenance stop valve with bellows seal - metallic sealing ARI-FABA -Plus - Straight through with flanges DIN DVGW-Type approval TA - Luft TÜV-Test-No. 973-10183778
Stop valve with soft seal Free of maintenance stop valve - soft sealed (to 120 C)
ARI-EURO-WEDI Stop valve with soft seal Free of maintenance stop valve - soft sealed (to 120 C) ARI-EURO-WEDI - Fig. 070 Page 2 ARI-EURO-WEDI - Fig. 071 Page 2 Fig. 070 ARI-EURO-WEDI - Hood valve Fig.
ARI-STEVI BBD 415 (DN25-50) Straight through blow down valve
With pneumatic actuator ARI-STEVI BBD 415 (DN25-50) Straight through blow down valve ARI-STEVI BBD 415 Pneumatic actuator Required air supply pressure max. 6 bar Options: - Assembly of additional devices
ARI-CHECKO -V / -D Check valve ARI-Check valve, metallic sealing
ARI-CHECKO -V / -D Check valve ARI-Check valve, metallic sealing Straight through with flanges (except EN-JL1040) Straight through with flanges Straight through with flanges Angle pattern with flanges
Cast iron Nodular iron Cast steel BR 003/303 Page 2. Cast iron Nodular iron Cast steel BR 004/304 Page 3. Forget steel BR 030 Page 4
Check valve Straight through with flanges (except GG-25) Cast iron Nodular iron Cast steel BR 003/303 Page 2 Straight through with flanges Forged steel BR 003 Page 2 BR 003 Straight through with flanges
Pressure reducing valve Pressure reducing valve in straightway form DN
Pressure reducing valve Pressure reducing valve in straightway form DN 15-150 ARI-PREDU Pressure regulating valve, straight through with diaphragm actuator DMA Actuator with rolling diaphragm Grey cast
STEVI 440 / 441. Straight through control valve DN
with electric and pneumatic actuators Straight through control valve DN 15-100 Electric actuator ARI-PREMIO Enclosure IP 65 2 torque switches 1 travel switch Handwheel Additional devices available, e.g.
ARI-STEVI 423 / 463 (DN ) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring)
With pneumatic and electric actuators ARI-STEVI 423 / 463 (DN200-300) Control valve - 3-way-form (mixing/diverting valve) (optional with screwed seat ring) ARI-STEVI 423 / 463 Pneumatic actuator ARI-DP
Excess pressure regulator Excess pressure regulator, straight through DN
ARI-PREDEX Excess pressure regulator Excess pressure regulator, straight through DN 15-150 ARI-PREDEX Excess pressure regulator, straight through with diaphragm actuator UDA Actuator with rolling diaphragm
PN63 - PN160. ARI-STOBU PN Stuffing box valve. Stop valve with gland seal - metallic sealing. ARI-STOBU - Straight through with flanges
Stuffing box valve Stop valve with gland seal - metallic sealing ARI-STOBU - Straight through with flanges PN63 - PN160 Forged steel High temperature steel Fig. 006 Seite 2 ARI-STOBU - Straight through
Cast iron Nodular iron BR 006/306 Page 2. BR 006/306 Page 2. Forged steel BR 006 Page 3. Stainless steel BR 006 Page 3. Forged steel BR 005 Page 5
ARI-STOBU - Stop valve with gland seal STOBU Stop valve with gland seal ARI-STOBU Globe valve with flanges TRB 801 No.45 (except cast iron) ARI-STOBU Globe valve with flanges TRB 801 No.45 Test approvals
Spring Loaded Safety Valve. SiC 11/13/14
Spring Loaded Safety Valve SiC 11/13/14 General Features and Benefits Acc. Directive 97/23/EC of the European Parliament and the Council of 29 May 1997 on the approximation of the laws of the Member States
Cast iron Nodular iron BR 006/306 Page 2. Cast steel BR 006/306 Page 2. Forged steel BR 006 Page 3. Stainless steel BR 006 Page 3
ARI-STOBU - Stop valve with gland seal STOBU Stop valve with gland seal ARI-STOBU Globe valve with flanges TRB 801 No.45 (without GG-25) Cast iron Nodular iron BR 006/306 Page 2 ARI-STOBU Globe valve with
ARI-STEVI 440 / 441 DVGW type approval
ARI-STEVI 440 / 441 DVGW type approval Control valve in straightway form for combustible gases DIN-DVGW type approval DN 15-100 ARI-STEVI 440-G / 441-G for electric and pneumatic actuators DIN-DVGW type
Control valve - 3-way with flanges (3-way mixing valve / 3-way diverting valve) DN 200 and 250
with electric and pneumatic actuators Control valve - 3-way with flanges (3-way mixing valve / 3-way diverting valve) DN 200 and 250 Electric actuator ARI-PREMIO Enclosure IP 65 2 torque switches Handwheel
Type 441 CATALOG. Flanged Safety Relief Valves. The-Safety-Valve.com
Type 441 Flanged Safety Relief Valves CATALOG The-Safety-Valve.com General Information LESER India Safety Relief Valves The safety valve Type 441 represents High capacity related to the safety valve size
Temperature regulator Temperature regulator DN
Temperature regulator Temperature regulator DN 15-100 Fig. 771 ARI-TEMPTROL Thermal closing valve straight through with flanges Fig. 771 Fig. 772 Page 2 Fig. 773 ARI-TEMPTROL LCG Thermal closing valve
Butterfly valves ARI-ZIVA -Z / ARI-ZIVA -G. with notch lever. with worm gear. with electric rotary actuator rotork
Butterfly valves ARI-ZIVA -Z - Fig. 014 - Free of maintenance wafer pattern butterfly valve - soft sealed - industrial range ARI-ZIVA -G - Fig. 015 - Free of maintenance butterfly valve with threaded eyelets
Type. Type 457, , 458. Flanged Safety Relief Valves spring loaded
Type Type 458 Packed lever H4 Closed bonnet Conventional design 457, 458 Flanged Safety Relief Valves spring loaded Contents Chapter/Page Materials Conventional design 09/02 Balanced bellows design 09/04
ARI-FABA LA Stop valve with bellows seal Free of maintenance stop valve with bellow seal - metallic sealing - long construction
ARI-FABA LA Stop valve with bellows seal Free of maintenance stop valve with bellow seal - metallic sealing - long construction ARI-FABA LA - Straight through with flanges EN ISO 15848-1 / TA - Luft TÜV-Test-No.
with electric and pneumatic actuators Control valve in 3-way-form (3-way mixing valve) DN 300 ARI-STEVI 423 Electric actuator ARI-PREMIO
with electric and pneumatic actuators Control valve in 3-way-form (3-way mixing valve) DN 300 Electric actuator ARI-PREMIO Enclosure IP 65 2 torque switches Handwheel Additional devices available, e.g.
API CATALOG. Flanged Safety Relief Valves Series 526. The-Safety-Valve.com
API Flanged Safety Relief Valves Series 526 CATALOG The-Safety-Valve.com NH 3 HCL Product Range LESER Safety Valves for every industrial application API High Performance Series 526 Type 526 Compact Performance
ARI-Check valve. ARI-Check valve, metallic sealing. ARI-Check valve - Straight through with flanges. ARI-Check valve - Straight through with flanges
ARI-Check valve, metallic sealing Straight through with flanges (except EN-JL1040) Grey cast iron SG iron Cast steel Fig. 003/303 Page 2 Straight through with flanges Straight through with flanges Angle
Forged steel Fig. 640/641 (Y) Page 6
Thermodynamic steam trap CONA TD ANSI Thermodynamic steam trap Thermodynamic steam trap ANSI150 / - with flanges (Fig. 640/641...1) - with screwed sockets (Fig. 640/641...2) - with socket weld ends (Fig.
ARI-STOBU PN16-40 Stuffing box valve Stop valve with gland seal metal seat
ARI-STOBU PN16-40 Stuffing box valve Stop valve with gland seal metal seat Straight through with flanges TRB 801 Annex II No. 45 (except EN-JL1040) (optional) Straight through with flanges TRB 801 Annex
Type 459. Type. 459 Safety Relief Valves spring loaded
Type Plain lever H3 459 Safety Relief Valves spring loaded Contents Chapter/Page Cap H2 Materials Available designs 05/02 Available designs materials 05/03 How to order Numbering system 05/04 Article numbers
Page 6. Page 6. Page 6. Page 7. Page 8. Page 9. Page 10 / 11
Butterfly valves ARI-ZIVA -Z - Fig. 014 - Free of maintenance wafer pattern butterfly valve - soft sealed - industrial range ARI-ZIVA -G - Fig. 015 - Free of maintenance butterfly valve with threaded eyelets
Forged steel Stainless steel Fig. 610/612 (Y) Page 2. Forged steel Fig. 616 Page 6
Thermostatic steam trap CONA M ANSI Thermostatic steam trap Thermostatic steam trap ANSI150 / - with flanges (Fig. 610/612...1) - with screwed sockets (Fig. 610/612...2) - with socket weld ends (Fig. 610/612...3)
Butterfly valves. ARI-ZIVA -Z - Fig Free of maintenance wafer pattern butterfly valve - soft sealed - industrial range
ARI-ZIVA -Z - Fig. 014 - Free of maintenance wafer pattern butterfly valve - soft sealed - industrial range ARI-ZIVA -Z / ARI-ZIVA -G Butterfly valves ARI-ZIVA -G - Fig. 015 - Free of maintenance butterfly
Type 455, 456. Facts. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. US Units
Type 455, 456 Flanged Safety Relief Valves spring loaded US Units Facts The-Safety-Valve.com LWN 468.08-E 462.01-D 40 Cap H2 19 Lock nut 18 Adjusting screw 16 Upper spring plate 9 Bonnet 12 Spindle 54
ARI-STOBU PN16-40 Stuffing box valve
Stuffing box valve Stop valve with gland seal - metallic sealing Straight through with flanges TRB 801 Annex II No. 45 (except EN-JL1040) German TA-Luft TÜV-Test-No. 922-9204866 Grey cast iron SG iron
ARI-STEVI H / with electric actuators
Control valve in 3-way-/straightway form in compact-design for HVAC Applications - Fig. 491 / Fig. 492 Control valve in 3-way-/straightway form for HVAC Applications - Fig. 485/487 / Fig. 486/488 ARI-STEVI
High temperature steel Fig. 600 Page 8. High temperature steel Fig. 600 Page 10. High temperature steel Fig. 600 Page 12
Bimetallic steam trap CONA B ANSI Bimetallic steam trap Bimetallic steam trap ANSI150 / - with flanges (Fig. 600/601...1) - with screwed sockets (Fig. 600/601...2) - with socket weld ends (Fig. 600/601...3)
ARI-ZESA / ARI-GESA / THEA Butterfly valves
ARI-ZESA - Fig. 012 - Free of maintenance butterfly valve with elongated eyelets - soft sealed ARI-GESA - Fig. 013 - Free of maintenance butterfly valve with threaded eyelets - soft sealed / THEA Butterfly
High CATALOG 2. Performance. Flanged Safety Relief Valves Series 441 Full nozzle Series 458
High Performance Flanged Safety Relief Valves Series 441 Full nozzle Series 458 CATALOG 2 NH 3 HCL Product Range LESER Safety Valves for every industrial application High Performance Compact Performance
AN ISO 9001:2008 CERTIFIED COMPANY. Safety Valve
AN ISO 9001:2008 CERTIFIED COMPANY Safety Valve SAFETY VALVE FEATURE : - The Cr-V spring & novel disc & seat design provide reliable bubble tight seal. - Excellent re-seating ability - It features heavy-duty
High CATALOG 1. Performance. Flanged Safety Relief Valves Series 441 Series XXL Series 444
High Performance Flanged Safety Relief Valves Series 441 Series XXL Series 444 CATALOG 1 Product Range LESER Safety Valves for every industrial application High Performance Compact Performance Series 441
Si Safety valves for pressure relief in accordance to PED, DIN/EN and ASME. Engineering GREAT Solutions
Safety valves for pressure relief in accordance to PED, DIN/EN and ASME Engineering GREAT Solutions Features Typical regular safety valve for many applications The modern pressure safety valve for regular
PN63 - PN160. with electric and pneumatic actuators. Control valve in straightway form with flanges and butt weld ends (shoed ends) DN
with electric and pneumatic actuators Control valve in straightway form with flanges and butt weld ends (shoed ends) DN 15-100 PN63 - PN160 ARI-STEVI 472 Electric actuator ARI-PREMIO Enclosure IP 65 2
High CATALOG 1. Performance. Flanged Safety Relief Valves Series 441 Series XXL Series 444. The-Safety-Valve.com
High Performance Flanged Safety Relief Valves Series 441 Series XXL Series 444 CATALOG 1 The-Safety-Valve.com NH 3 HCL Product Range LESER Safety Valves for every industrial application High Performance
Compact. Performance. Safety Relief Valves Series 437 Series 459. The-Safety-Valve.com
Compact Performance Safety Relief Valves Series 437 Series 459 EXTENDED CATALOG The-Safety-Valve.com Valve Finder How to find the right Product Group High operating to set pressure ratio, high backpressure
Spring loaded Thermal Relief Safety Valves, manufacturers standard Medium and high pressure
Series Thermal Relief Safety Valves Spring loaded Thermal Relief Safety Valves, manufacturers standard Medium and high pressure Applications The Sempell series provides a complete and comprehensive range
High temperature steel Fig. 600 Page 8. High temperature steel Fig. 600 Page 10. High temperature steel Fig. 600 Page 12
Bimetallic steam trap CONA B ANSI Bimetallic steam trap Bimetallic steam trap ANSI150 / - with flanges (Fig. 600/601...1) - with screwed sockets (Fig. 600/601...2) - with socket weld ends (Fig. 600/601...3)
Si Safety valves for pressure relief in accordance to PED, DIN/EN and ASME. Engineering GREAT Solutions
Safety valves for pressure relief in accordance to PED, DIN/EN and ASME Engineering GREAT Solutions Features The regular safety valve for low pressures: > Cost-effective body design with seat bushing >
Si Engineering GREAT Solutions. Process and steam safety valves to PED and DIN/EN standards
Engineering GREAT Solutions Process and steam safety valves to PED and DIN/EN standards Si 4302 Features Engineered with high discharge The state-of-the-art IMI Bopp & Reuther medium-pressure safety valve:
Si Engineering GREAT Solutions. Process and steam safety valves to PED and DIN/EN standards
Engineering GREAT Solutions Process and steam safety valves to PED and DIN/EN standards Features Basic valve for low pressure Cost-efficient IMI Bopp & Reuther low pressure safety valve: > Semi nozzle
SVL488 Stainless Steel Safety Valve for Clean Service Applications
Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without
Float-operated condensate pump ARI Condensate pump (mechanical) Displacement: 16,5-20 litres. High temperature steel. Stainless steel.
Float-operated condensate pump ARI Condensate pump (mechanical) Displacement: 16,5-20 litres Condensate pump No electricity required / float-operated PN 16 (82.691) Body: Jacket P235GH-TC, Bottom flanges
CROSBY STYLE JB PRESSURE RELIEF VALVE
A large orifice pressure relief valve engineered to provide high quality, dependable overpressure protection for air, gas, vapor and steam applications FEATURES Ten size product range is the broadest available.
Type 441 ANSI 442 ANSI. Facts. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. US Units
Type 441 ANSI 442 ANSI Flanged Safety Relief Valves spring loaded US Units Facts The-Safety-Valve.com LWN 462.05-E 462.01-D Conventional design 40 Cap H2 18 19 16 Adjusting screw Lock nut Upper spring
Forged steel High temperature steel Stainless steel Fig. 640/641 (Y) Page 2. High temperature steel Fig. 640/641 (Y) Page 6
Thermodynamic steam trap CONA TD Thermodynamic steam trap Thermodynamic steam trap PN40 - with flanges (Fig. 640/641...1) - with screwed sockets (Fig. 640/641...2) - with socket weld ends (Fig. 640/641...3)
Pneumatic process valve, Y-pattern with pneumatic actuator of stainless steel DN 15-50
with pneumatic actuator of staless steel Pneumatic process valve, Y-pattern with pneumatic actuator of staless steel DN 15-50 ARI-STEVI AS 350 Pneumatic actuator - with screwed sockets Piston actuator
Type 441 DIN 442 DIN. Facts. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. US Units
Type 441 DIN 442 DIN Flanged Safety Relief Valves spring loaded US Units Facts The-Safety-Valve.com LWN 462.02-E 462.01-D Conventional design 40 Cap H2 18 Adjusting screw 19 Lock nut 16 Upper spring plate
Si 6303 / Si 6304 / Si 6305
Si 6303 / Si 6304 / Si 6305 Engineering GREAT Solutions Process and steam safety valves to PED and DIN/EN standards Si 6303 / Si 6304 / Si 6305 Si 6303 / Si 6304 / Si 6305 Features Engineered for high
API Flanged Safety Relief Valves Series 526 API CATALOG. LESER worldwide. The-Safety-Valve.com. The-Safety-Valve.com
LESER UK Bristol, United Kingdom sales@leser.co.uk André Ramseyer AG Flamatt, Switzerland info@ramseyer.ch API LESER worldwide Hong Kong LESER Shenzen, China sales@leserchina.com API Flanged Safety Relief
Si 2323 / Si 2324 / Si 2325
Safety valves for pressure relief in accordance to PED, DIN/EN and ASME Engineering GREAT Solutions Si 2323 / Si 2324 / Si 2325 Features Straightforward design for high pressures The regular flow safety
Model 1415 TOSACA TECHNICAL DATA SHEET. Construction and materials. Technical information
Model 1415 TECHNICAL DATA SHEET Description Requirements Type Safety and Relief valve Calculation API RP 520 Connections Flanged ASME/ANSI B16.5 Design / Size API STD 526, ASME Section VIII Rating 150#/300#
GERMAN QUALITY VALVES
The pneumatic Y-pattern process valve: Up to 31% energy saving Excellent value for money Convenient handling Reliable even at high differential pressures: Stays tight for up to 1,000,000 cycles! NEW from
SV80H Safety and Relief Valves
Page 1 of 18 BR Rev.02 U SH Safety and Relief alves Description The SH is a full nozzle safety and relief valve with orifices D to T, comply with the API STD 526, beyond others with super capacity. Suitable
High Flow Safety Valves
High Flow Safety Valves Engineering GREAT Solutions Process and steam safety valves to PED and DIN/EN standards High Flow Safety Valves Valve summary Si 6301 Size DN 20 to DN 150 Set Pressure up to16 bar
Grey cast iron Fig. 610 Page 2. Forged steel Stainless steel Fig. 610/612 (Y) Page 4
Thermostatic steam trap CONA M Thermostatic steam trap Thermostatic steam trap PN16 - with flanges (Fig. 610...1) - union with butt weld ends (Fig. 610...5) Grey cast iron Fig. 610 Page 2 Thermostatic
Compact. performance. Threaded Safety Relief Valves. Series 437 Type Series 459 Type CATALOG.
Compact performance Threaded Safety Relief Valves Series 437 Type 437 438 439 Series 459 Type 459 46 CATALOG The Safety Valve Series 459 Packed lever H4 Series 459 Balanced bellows design Series 459 Cap
Si 910. Engineering GREAT Solutions. Safety Valves acc. to ASME Sec. I, Sec. III and Sec. VIII
Engineering GREAT Solutions Safety Valves acc. to ASME Sec. I, Sec. III and Sec. VIII Features IMI Bopp & Reuther steam safety valve acc. to ASME Sec. I > High capacity > Fixed overpressure and blowdown
Type. 437 Safety Relief Valves spring loaded
Type Packed knob H4 437 Safety Relief Valves spring loaded Packed knob H4 Flanged connection Cap H2 Contents Chapter/Page Materials Available designs 01/02 Available designs materials 01/03 How to order
Type 441 ANSI 442 ANSI. Facts. Flanged Safety Relief Valves spring loaded. The-Safety-Valve.com. Metric Units LWN E
Type 441 ANSI 442 ANSI Flanged Safety Relief Valves spring loaded Metric Units Facts The-Safety-Valve.com LWN 462.04-E Conventional design 40 Cap H2 18 19 16 Adjusting screw Lock nut Upper spring plate
Seri e s C ATA L O G. Series 526. The Safety Va l v e
API Seri e s Series 526 C ATA L O G The Safety Va l v e Type 526 Type 526 Balanced bellows design Type 526 Plain lever 3 Type 526 Open bonnet d Safety Relief s API Series Contents Contents Applications
Type 431, 433. Balanced bellows design. Type Cap H2. 18 Adjusting screw with bushing. 19 Lock nut. 16 Upper spring plate. 12 Spindle.
Balanced bellows design 40 Cap H2 18 Adjusting screw with bushing 19 Lock nut 16 Upper spring plate 12 Spindle 9 Bonnet 54 Spring 14 Split ring 17 Lower spring plate 55 Stud 56 Nut 8 Guide with bushing
CONA ANSI Further components / Accessories
CONA ANSI Further components / Accessories Liquid drainer ANSI150 / 300 - with flanges (Fig. 665...1) - with screwed sockets (Fig. 665...2) - with socket weld ends (Fig. 665...3) - with butt weld ends