Booster Pumps. Non-Submersible Pumps. BT4 Series. Cast Iron Features: Applications:
|
|
|
- Marian Taylor
- 5 years ago
- Views:
Transcription
1 BT4 Series CSA ENC 3 COF CSA 3 C US CSA 18 UL 8 Applications: Boosting water pressure from either city mains or private water systems. Pressure washing buildings and floors. Poultry houses. Spray cooling equipment. Lawn and crop irrigation. Evaporative cooling system/misters. Water circulation. General purpose pumping. Reverse osmosis - stainless steel BT4. Filtration - stainless steel BT4. Note: 3 hp BT4 pumps are for indoor installations only. They are not rated for outdoor installations. Cast Iron Features: Designed for boosting water pressure from a variety of sources including municipal and private water systems. Stainless steel discharge head on all models. Cast iron motor bracket with a rugged support foot for horizontal or vertical mounting and a handle for portability of the unit. 1 suction and 1 discharge are the same across the entire line, simplifying installation and maintenance. The booster pump is built by Franklin Electric s patented (U.S.) Patent,29,984) Tri-Seal floating stage system, for maximum efficiency, longevity and performance. Assembled with the highest quality materials of construction, such as Celcon for impellers, Noryl for the diffusers and 3 series stainless steel for the hub, eye seals, shaft and shell. Easily serviced through a back pull-out design, which leaves all plumbing and the pump undisturbed in their original location. Industry proven square flange motors from A.O. Smith. Single-phase:1/3 through 2 hp motors are dual voltage, set to run with either 1 V or 23 V incoming power, while 3 hp are 23 V only. Motors are high service factor A.O. Smith. Shut-off pressures up to 2 psi, flow rates from 5 to gpm, and temperatures up to 1 F / 49 C. Stainless Steel Features: Includes all of the Cast Iron features above plus: Stainless steel models: Viton mechanical seal for corrosive fluids Three-phase also available: 1/2 through 3 hp motors are dual voltage set to run with either 8-23 V or 46 V incoming power. Stainless steel motor bracket with a rugged support foot for horizontal or vertical mounting, and a handle for portability of the unit. Designed for industrial applications. Celcon is a Registered Trademark of the Celanese Corporation. Noryl is a Registered Trademark of G.E. Viton is a Registered Trademark of Dupont Dow Elastomers. 1
2 BT4 Series - 5 Performance Curves /4 hp /2 hp 1/3 hp FT
3 BT4 Series - Performance Curves hp /4 hp 1 3 1/2 hp FT
4 BT4 Series - 1 Performance Curves hp hp /4 hp 1/2 hp FT
5 BT4 Series - Performance Curves hp hp /4 hp FT
6 BT4 Series - Performance Curves hp 14 2 hp hp /4 hp FT
7 BT4 Series - Performance Curves hp hp hp FT
8 126 Non-Submersible Pumps BT4 Series Ordering Information (See pgs. 2-3 for model number explanation) Single-Phase Stainless Steel (With Viton mechanical seal) HP Discharge x Suction Voltage Model No. Order No. Wt. 1/3 1 x 1 1/23 5FBT3S /2 1 x 1 1/23 5FBT5S /4 1 x 1 1/23 5FBTS x 1 1/23 5FBT1S /2 1 x 1 1/23 FBT5S /4 1 x 1 1/23 FBTS x 1 1/23 FBT1S x 1 1/23 FBTS /2 1 x 1 1/23 1FBT5S /4 1 x 1 1/23 1FBTS x 1 1/23 1FBT1S x 1 1/23 1FBTS x 1 1/23 1FBT2S /4 1 x 1 1/23 FBTS x 1 1/23 FBT1S x 1 1/23 FBTS x 1 1/23 FBT2S /4 1 x 1 1/23 FBTS x 1 1/23 FBT1S x 1 1/23 FBTS x 1 1/23 FBT2S x 1 23 FBT3S x 1 1/23 FBT1S x 1 1/23 FBTS x 1 1/23 FBT2S x 1 23 FBT3S Viton is a registered trademark of Dupont Dow Elastomers. Single-Phase Cast Iron HP Discharge x Suction Voltage Model No. Order No. Wt. 1/3 1 x 1 1/23 5FBT3C /2 1 x 1 1/23 5FBT5C /4 1 x 1 1/23 5FBTC x 1 1/23 5FBT1C Note: Weight in pounds. 1/2 1 x 1 1/23 FBT5C /4 1 x 1 1/23 FBTC x 1 1/23 FBT1C x 1 1/23 FBTC /2 1 x 1 1/23 1FBT5C /4 1 x 1 1/23 1FBTC x 1 1/23 1FBT1C x 1 1/23 1FBTC x 1 1/23 1FBT2C /4 1 x 1 1/23 FBTC x 1 1/23 FBT1C x 1 1/23 FBTC x 1 1/23 FBT2C /4 1 x 1 1/23 FBTC x 1 1/23 FBT1C x 1 1/23 FBTC x 1 1/23 FBT2C x 1 23 FBT3C x 1 1/23 FBT1C x 1 1/23 FBTC x 1 1/23 FBT2C x 1 23 FBT3C
9 BT4 Series Ordering Information (See pgs. 2-3 for model number explanation) Three-Phase Stainless Steel Non-Submersible Pumps HP Discharge x Suction Voltage Model No. Order No. Wt. 1/2 1" x 1" 8-23/46 5FBT5S4-T /4 1" x 1" 8-23/46 5FBTS4-T " x 1" 8-23/46 5FBT1S4-T /2 1" x 1" 8-23/46 FBT5S4-T /4 1" x 1" 8-23/46 FBTS4-T " x 1" 8-23/46 FBT1S4-T " x 1" 8-23/46 FBTS4-T /2 1" x 1" 8-23/46 1FBT5S4-T /4 1" x 1" 8-23/46 1FBTS4-T " x 1" 8-23/46 1FBT1S4-T " x 1" 8-23/46 1FBTS4-T " x 1" 8-23/46 1FBT2S4-T /4 1" x 1" 8-23/46 FBTS4-T " x 1" 8-23/46 FBT1S4-T " x 1" 8-23/46 FBTS4-T " x 1" 8-23/46 FBT2S4-T /4 1" x 1" 8-23/46 FBTS4-T " x 1" 8-23/46 FBT1S4-T " x 1" 8-23/46 FBTS4-T " x 1" 8-23/46 FBT2S4-T " x 1" 8-23/46 FBT3S4-T " x 1" 8-23/46 FBT1S4-T " x 1" 8-23/46 FBTS4-T " x 1" 8-23/46 FBT2S4-T " x 1" 8-23/46 FBT3S4-T Note: All weights in pounds. BT4 Pump End: HP Discharge x Suction Model No. Order No. Wt. 1/3 1" x 1" 5BT3S4-PE /2 3/4 1" x 1" 1" x 1" 5BT5S4-PE 5BTS4-PE " x 1" 5BT1S4-PE /2 1" x 1" BT5S4-PE /4 1" x 1" BTS4-PE " x 1" BT1S4-PE " x 1" BTS4-PE /2 1" x 1" 1BT5S4-PE /4 1" x 1" 1BTS4-PE " x 1" 1BT1S4-PE " x 1" 1BTS4-PE " x 1" 1BT2S4-PE /4 1" x 1" BTS4-PE " x 1" BT1S4-PE " x 1" BTS4-PE " x 1" BT2S4-PE /4 1" x 1" BTS4-PE " x 1" BT1S4-PE " x 1" BTS4-PE " x 1" BT2S4-PE " x 1" BT3S4-PE " x 1" BT1S4-PE " x 1" 1" x 1" BTS4-PE BT2S4-PE " x 1" BT3S4-PE Notes: All weights in pounds. 56Z motor size frame. BT4 pump ends are stainless steel construction. 12
10 BT4 Series Dimensional Data B A 9.4 C Single-Phase Stainless Steel & Cast Iron: HP Stage A B C 1/3 9.63" 13.49" 23.12" 1/ ".14".52" 5 3/ " 1.6" 28.6" ".6" 31.94" 1/ " 14.31" 24.69" 3/ ".96" 26.69" " 19.24" 31.12" " 23.35" 35.98" 1/2 1.38" 14." 24.45" 3/ " 14.98".98" " 1.69" 29.5" " 21.31" 33.94" " 24.2" 36.65" 3/ " 13.1" 24.1" " 14.98" 26.86" " 18.59" 31.22" " 21.31" 23.94" 3/ " 13.8" 24.8" " 16.31" 28.19" " 19.99" 32.62" " 22.43" 35.6" " 26.11" 39.29" ".9" 26.9" " 1.54" 3.1" " 19.99" 32.62" " 23.66" 36.84" 134 Three-Phase Stainless Steel: HP Stage A B C 1/ ".14" 24.99" 5 3/ " 1.6" 28.1" ".3" 3.88" 1/ " 14." 23.85" 3/ " 14.31" 24.81" ".96" 26.81" " 23.35" 35." 1/2 9.85" 14." 23.92" 3/ " 14.98".48" " 1.69" 28.54" " 21.31" 33.16" " 24.2" 36.62" 3/ " 13.1" 23.6" " 14.98".83" " 18.59" 3.44" " 21.31" 33.91" 3/ " 13.8" 24.3" " 16.31" 2.16" " 19.99" 31.84" " 22.43" 35.3" " 26.11" 38.8" ".9".94" " 1.54" 29.39" " 19.99" 32.59" " 23.66" 36.35"
Non-Submersible Pumps
BT4 Series CSA ENC 3 COF CSA 3 C US LR 898 Applications: Boosting water pressure from either city mains or private water systems Pressure washing buildings and floors Poultry houses Spray cooling equipment
Non-Submersible Pumps
BT4 Series Booster Pumps Cast Iron Features: Designed for boosting water pressure from a variety of sources including municipal and private water systems. Available with either cast iron or stainless steel
BOOSTER PUMPS PRODUCT FAMILY APPLICATIONS FAMILY COMPARISON CHART
BOOSTER PUMPS Franklin s booster pumps feature a stainless steel construction and are designed to meet any pressure-boosting need. The selection is available in a range of horsepower sizes, in single-
franklinwater.com 50 Hz 4 SUBMERSIBLE PUMPS
franklinwater.com 50 Hz 4 SUBMERSIBLE PUMPS 01 4 SUBMERSIBLE PUMPS 4400 Tri-Seal Pumps 3 18 LPM Tri-Seal 5 25 LPM Tri-Seal 7 30 LPM Tri-Seal 9 45 LPM Tri-Seal 11 60 LPM Tri-Seal 13 70 LPM Tri-Seal 15 4400
PRODUCT CATALOG SURFACE PUMPS RESIDENTIAL & LIGHT COMMERCIAL. franklinwater.com
PRODUCT CATALOG SURFACE PUMPS RESIDENTIAL & LIGHT COMMERCIAL franklinwater.com RESIDENTIAL & LIGHT COMMERCIAL SURFACE PUMPS Jet Pumps... 2 Shallow Well VersaJet...3 SWJ (Cyclone) Series...5 Convertible
NEW! BOOSTER PUMPS. HBP/HBPS series 4" horizontal booster pumps. booster pumps
HBP/HBPS series 4" horizontal The HBP/HBPS Series Booster Pumps are the most durable available. The patented SignaSeal floating impeller design minimizes thrust loads, allowing for continuous operation
V6 Vertical Pumps. Multi-Stage Pumps. Features: BOOK: MSP-010 DATE: Jan. 1, 2012
BOOK: MSP-1 DATE: Jan. 1, 212 The V6 Booster Pump is ideal for industrial/commercial applications where water pressure boosting is required. Designed with premium hydraulics for reliability and excellent
Series. NV Vertical Multistage Booster Pump
NV Vertical Multistage Booster Pump Series This series of vertical multistage booster pumps offer technically advanced designs to meet market demands including hot water applications. Every NV Series pump
5GB, 7GB, 10GB, 18GB, 25GB, 33GB
B-33GB GB, 7GB, GB, 18GB, 2GB, 33GB High Pressure Multi-Stage Booster Pump FEATURES Multi-stage Design: Provides steady, quiet, vibration free, operation. Optional Stainless Steel Construction: Standard
Table of Contents. 4 Submersible Pumps
5 Hz 4 Submersible Pumps Table of Contents 4 Submersible Pumps 44 Tri-Seal Pumps... 2 18 LPM Tri-Seal... 5 25 LPM Tri-Seal... 7 3 LPM Tri-Seal... 9 45 LPM Tri-Seal... 11 6 LPM Tri-Seal... 13 7 LPM Tri-Seal...
4" Submersible Pumps. The Company You Trust Deep Down
4" Submersible Pumps The Company You Trust Deep Down 4" Submersible Series Five The standard J-Class Series Five submersible pump features unique hydraulics that improve effi ciency and minimize wear even
Six-Inch Submersible Pumps
FW1 87 5 thru 5 5 to GPM Supersedes Six-Inch Submersible Pumps Series 6P and 6T High capacity six-inch submersible pumps for commercial, industrial, agricultural, municipal and other deep well, large water
WG / WGS HIGH PRESSURE BOOSTER PUMPS
Date: June 1, 6 Section: 9 Page: 1 Cancel & replace: 03-01-1 WG / WGS HIGH PRESSURE BOOSTER PUMPS This type of pump is ideal for pressure up to 320 P.S.I. (2 kpa) and when boosting is necessary. In addition
ITT. Goulds Pumps. 5GB, 7GB, 10GB, 18GB, 25GB, 33GB High Pressure Multi-Stage Booster Pump. Engineered for life. Residential Water Systems FEATURES
Goulds Pumps GB, 7GB, 1GB, 18GB, 2GB, 33GB High Pressure Multi-Stage Booster Pump FEATURES Multi-stage Design: Provides steady, quiet, vibration free, operation. Optional Stainless Steel Construction:
Aermotor 4 Submersible Pumps - 5, 8, 12, 16, 20, 22 & 25 GPM
A+ SUPER SUB series stainless steel Precision engineered stainless steel 4 submersible pumps that deliver dependable performance and efficiency in all applications. Heads to 000 feet and capabilities to
High Capacity Centrifugal & Sprinkler Pumps
High Capacity Centrifugal & Sprinkler Pumps FW0724 1016 Supersedes 0212 Stainless steel or cast iron construction Stainless steel impellers Discharge rotates in 90 increments on some models Pressures to
TECHNICAL BROCHURE B5-33GB R4 5GB, 7GB, 10GB, 18GB, 25GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP
TECHNICAL BROCHURE B-33GB R4 GB, 7GB, GB, 1GB, 2GB, 33GB HIGH PRESSURE MULTI-STAGE BOOSTER PUMP FEATURES Multi-stage Design: Provides steady, quiet, vibration free, operation. applications. O-Ring Casing
ITT. Red Jacket Water Products GRIZZLY. red JaCKet Water Products. Engineered for life BRJGRIZZ. Residential Water Systems.
BRJGRIZZ ITT Red Jacket Water Products GRIZZLY Features n Nylon impact and corrosion resistant discharge head and motor adapter. n Pump shell constructed with a press and roll process for better performance.
ITT. Goulds Pumps 45J and 70J. Engineered for life B45-70J. Residential Water Systems. Features. 60 Hz High Capacity Flat Bowl 6" Submersible Pumps
B45-7J Goulds Pumps 45J and 7J Hz High Capacity Flat Bowl 6" Submersible Pumps For 6" and larger wells Goulds Pumps is a brand of Corporation. www.goulds.com Engineered for life Features n Powered for
HIGH CAPACITY CENTRIFUGAL & SPRINKLER PUMPS
HIGH CAPACITY CENTRIFUGAL & SPRINKLER PUMPS FW0724 0707 Supersedes 1005 Straight Centrifugal Pumps Electric Motors Heavy Duty Straight Centrifugal Pumps High Head Straight Centrifugal Pumps Stainless Steel
franklinwater.com 50 Hz VR SERIES Vertical Multi-Stage Pumps
franklinwater.com 5 Hz VR SERIES Vertical Multi-Stage Pumps 5 HZ VR SERIES VERTICAL MULTI-STAGE PUMPS Features 2 Applications 2 Pump Specifications Counter-Flange Kits Motor Specifications 4 Ordering
VERTICAL SERIES BOOSTER PUMPS
VERTICAL SERIES BOOSTER PUMPS Stainless Steel Vertical Multistage Centrifugal Pump The Webtrol V Series Vertical multistage pumps offer technically advanced designs to meet market demands including hot
VERTICAL SERIES BOOSTER PUMPS
VERTICAL SERIES BOOSTER PUMPS Stainless Steel Vertical Multistage Centrifugal Pump The Webtrol V Series Vertical multistage pumps offer technically advanced designs to meet market demands including hot
TECHNICAL BROCHURE BSPMSPH R1 SOLD SEPARATELY OR BUILT IN. PrimeLine SP SPM & SPH SERIES
TECHNICAL BROCHURE BSPMSPH R1 SOLD SEPARATELY OR BUILT IN PrimeLine SP SPM & SPH SERIES FEATURES Self Priming Design: Features a replaceable check valve which acts to retain sufficient liquid in the casing
REDUCED DIAMETER SUBMERSIBLE PUMPS
3200 SERIES REDUCED DIAMETER SUBMERSIBLE PUMPS The 3200 Series submersible pumps are designed so that all parts of the pump end, including the cable guard, fall within the diameter of Franklin Electric
PRODUCT CATALOG SUBMERSIBLE PUMPS RESIDENTIAL & LIGHT COMMERCIAL. franklinwater.com
PRODUCT CATALOG SUBMERSIBLE PUMPS RESIDENTIAL & LIGHT COMMERCIAL franklinwater.com SUBMERSIBLE PUMPS Model Number Nomenclature...2 4" 32 Series Pumps...4 Ordering Information...5 5 gpm...6 7 gpm...8 1
4" SUBMERSIBLE PUMPS 5, 8, 12, 16, 20, 22 AND 25 GPM
4" SUBMERSIBLE PUMPS 5, 8, 12, 16, 2, 22 AND 25 GPM Precision engineered stainless steel that deliver dependable performance and efficiency in all applications. Heads to 1 feet and capabilities to 35 GPM.
VERTICAL MULTI-STAGE PUMPS
VR SERIES - 6 HZ FEATURES All 316 stainless steel hydraulic components for superior durability, efficiency, and performance over a wide variety of applications Rugged NEMA motor mounting with oversized
EZ SERIES BOOSTER PUMPS
EZ SERIES BOOSTER PUMPS Cast Iron And Stainless Steel Booster Pumps Webtrol has been building Booster Pumps for over years for various industrial, commercial and agricultural uses and has long been a leader
VERTICAL MULTI-STAGE PUMPS
VR SERIES - 6 HZ FEATURES All 316 SS hydraulic components for superior durability, efficiency, and performance over a wide variety of applications Rugged NEMA motor mounting with oversized ball bearings
5LS, 7LS, 10LS, 13LS, 18LS & 25LS 5-25 GPM, ½ 1½ HP, 60 HZ, SUBMERSIBLE PUMPS
TECHNICAL BROCHURE B5-25LS FEATURES Powered for Continuous Operation: All ratings are within the working limits of the motor as recommended by the motor manufacturer. can be operated continuously without
S SERIES 4" SUBMERSIBLE PUMPS FEATURES. Smooth and Quiet Precision-crafted, 4" submersible well pumps for quieter operation
S SERIES The S Series 4" submersibles have been a successful entry in the Myers well pump line for many years and have a history of tremendous reliability. The all stainless steel construction is ideal
RSV Series In-Line Vertical Multi-Stage, Ring Section Pump September 2013
1.0 Overview. The RSV series is Carver s multi-stage pump for water with maximum working pressures below 440 PSI. For other clean liquids please contact Carver Pump Company or your local distributor. The
50 to 250 GPM Submersible Pumps For Six-Inch Wells. 325 & 400 GPM Submersible Pumps For Eight-Inch Wells
FW5 39B Supersedes 39 5 to 25 GPM Submersible Pumps For Six-Inch Wells & GPM Submersible Pumps For Eight-Inch Wells Series 6P, 6T and 8T High capacity six or eight inch submersible pumps for commercial,
Technical Data Sheet PF Series 4" (100 mm) Submersible Effluent Pumps. 1 8-inch (3-mm) bypass orifice (patent pending) to ensure flow
Technical Data Sheet PF Series 4" (1 mm) Submersible Effluent Pumps Applications Our 4" (1 mm) Submersible Effluent Pumps are designed to transport screened effluent (with low TSS counts) from septic tanks
SELF-PRIMING PUMPS PRODUCT FAMILY APPLICATIONS FAMILY COMPARISON CHART
SLF-PRIMING PUMPS Irrigation and sprinkler pumps are designed for supplying large volumes of water from a lake or pond supply to an irrigation system. They can also be in highvolume applications transferring
5GS, 7GS, 10GS, 13GS, 18GS & 25GS 5-25 GPM, ½ 5 HP, 60 HZ, SUBMERSIBLE PUMPS
TECHNICAL BROCHURE B5-25GS FEATURES Powered for Continuous Operation: All ratings are within the working limits of the motor as recommended by the motor manufacturer. can be operated continuously without
PF Series 60-Hz, 4-inch (100-mm) Submersible Effluent Pumps
PF Series 6-Hz, 4-inch (1-mm) Submersible Effluent Pumps Applications Our 4-inch (1-mm) Submersible Effluent Pumps are designed to transport screened effluent (with low TSS counts) from septic tanks or
Aermotor 4 SUBMERSIBLE PUMPS 35, 50, 75, 90 GPM A+ SUPER SUB Series stainless steel
A+ SUPER SUB Series stainless steel The A+ Super Sub Series Stainless Steel 4 Submersible Pumps deliver efficient and dependable performance even in rough, aggressive water. Heads to 640 feet and capabilities
Jet Pumps - Convertible
Jet Pumps - onvertible onvertible VersaJet Series imensions: 92 S EN 3 OF S 3 US 3.68" 10.33" 2.19" 1" - 11 1/2 NPT 5.75" ISHRGE 1.69" 3.70" 3.70" 1 1/4" - 11 1/2" NPT 1" - 11 1/2" NPT imensional illustration
D Series. Centrifugal Pumps. Pump End Kits. Features: PAGE: CP-435 DATE: June 5, 2006
D Series Pump End Kits PAGE: CP-43 DATE: June, 06 D Maximize your fl exibility and response time for standard or special applications using end suction centrifugal pumps... industrial use, transfer circulation
5CS, 7CS, 10CS, 13CS, 18CS & 25CS 5-25 GPM, ½ 3 HP, 60 HZ, SUBMERSIBLE PUMPS
FEATURES Powered for Continuous Operation: All ratings are within the working limits of the motor as recommended by the motor manufacturer. can be operated continuously without damage to the motor. Sand
EZ SERIES BOOSTER PUMPS
EZ SERIES BOOSTER PUMPS Cast Iron And Stainless Steel Booster Pumps Webtrol has been building Booster Pumps for over years for various industrial, commercial and agricultural uses and has long been a leader
EZ SERIES BOOSTER PUMPS
EZ SERIES BOOSTER PUMPS Cast Iron And Stainless Steel Booster Pumps Webtrol has been building Booster Pumps for over 4 years for various industrial, commercial and agricultural uses and has long been a
EZ SERIES BOOSTER PUMPS
EZ SERIES BOOSTER PUMPS Cast Iron And Stainless Steel Booster Pumps Webtrol has been building Booster Pumps for over 4 years for various industrial, commercial and agricultural uses and has long been a
EZ SERIES BOOSTER PUMPS
EZ SERIES BOOSTER PUMPS Cast Iron And Stainless Steel Booster Pumps Webtrol has been building Booster Pumps for over 4 years for various industrial, commercial and agricultural uses and has long been a
EZ SERIES BOOSTER PUMPS
EZ SERIES BOOSTER PUMPS Cast Iron And Stainless Steel Booster Pumps Webtrol has been building Booster Pumps for over years for various industrial, commercial and agricultural uses and has long been a leader
EZ SERIES BOOSTER PUMPS
EZ SERIES BOOSTER PUMPS Cast Iron And Stainless Steel Booster Pumps Webtrol has been building Booster Pumps for over 4 years for various industrial, commercial and agricultural uses and has long been a
NDP-25 Specifications
NDP-25 Specifications Port Dimensions (46.2 GPM Max.) Intake & discharge connection: Polypropylene (PPG) Kynar (PVDF) Aluminum (ADC-12) Stainless Steel (316) Cast Iron Air inlet (incl. ball valve): Air
Submersible Pumps. 5'' CS Series Pumps
5'' CS Series Pumps 1 Submersible Pumps 5 5 CS CS Series Pumps Features Ordering Information Model Number Explanation 3 CS 4-1 Ordering Information Phase No. of Stages Series m 3 /hr @ BEP Model FE Order
Webtrol s Family of Pumps
www.webtrol.com Webtrol s Family of Pumps Vertical Series Booster Pumps Stainless Steel Multistage Centrifugals The Webtrol V Series multistage pumps offer technically advanced designs to meet market demands
NDP-50 Specifications
NDP-50 Specifications Port Dimensions Intake & discharge connection: (164 GPM Max.) Polypropylene (PPG) 2" ANSI B16.5 #150 Kynar (PVDF) 2" ANSI B16.5 #150 Aluminum (ADC-12) 2" ANSI B16.5 #150 (with tapped
ITT. Engineered for Life. GS Subs, New Guardian System and You, Stronger Together!
GS Subs, New Guardian System and You, Stronger Together! GS Submersibles have always had a reputation for being reliable and tough pumps. Now the best is even better! The new Guardian System now makes
BVM SERIES.
BERKELEY BVM SERIES vertical multi-stage pumps www.berkeleypumps.com Berkeley BVM SERIES vertical multi-stage pumps Standing tall in demanding high-pressure and high-temperature applications Berkeley Vertical
CENTRIFUGAL PUMPS GAS ENGINE FTSP FEATURES APPLICATIONS SPECIFICATIONS
FEATURES Volute: Ductile iron rugged construction. Self-priming with priming and drain plugs. Removable front cover features a built-in check valve to facilitate priming Impeller: Cast iron semi-open,
33GS, 40GS, 55GS, 60GS, 75GS & 80GS GPM, 1 10 HP, 60 HZ, SUBMERSIBLE PUMPS
TECHNICAL BROCHURE B33-8GS FEATURES Powered for Continuous Operation: All ratings are within the working limits of the motor as recommended by the motor manufacturer. can be operated continuously without
Spray Pressure Control Manifold
Instruction Sheet P/N 0870G0 WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction The
ITT. Goulds Pumps G&L Series NPO. Engineered for life. Commercial Water. Open Impeller All Stainless Steel End Suction Pumps.
ITT Goulds Pumps G&L Series NPO Open Impeller All Stainless Steel End Suction Pumps www.goulds.com Engineered for life A Full Range of Product Features NPO Product Line Numbering System Superior Materials
DPS. The SSV Dual Pump System
DPS The SSV Dual Pump System A Full Range of Product Features The DPS series of 36L stainless steel vertical multi-stage pumps from G&L has been designed to provide reliable high pressure boosting to serve
ITT. Goulds Pumps. Marlow Series 20EVP. Engineered for life. Commercial Water
Goulds Pumps Marlow Series 2EVP Vertical In-Line Self-Priming Centrifugal Pumps for Petroleums and Solvents STANDARD UNIT INCLUDES: Goulds Pumps is a brand of ITT Corporation. www.goulds.com Engineered
Spray Pressure Control Manifold
Instruction Sheet P/N 0870-0 WARNING: Allow only qualified personnel to perform the following tasks. Follow the safety instructions in this document and all other related documentation. Introduction The
ITT. Goulds Pumps 5GS, 7GS, 10GS, 13GS, 18GS & 25GS. Engineered for life B5-25GS. Residential Water Systems FEATURES
B5-25GS ITT Goulds s 5GS, 7GS, 1GS, 13GS, 18GS & 25GS 5-25, ½ 5, 6 Hz, Submersible s Goulds s is a brand of ITT Corporation. www.goulds.com Engineered for life FEATURES n Powered for Continuous Operation:
4 WT SERIES SUBMERSIBLE
4 WT SERIES SUBMERSIBLE Webtrol s 4 WT Series Webtrol s WT Series pumps offer superior performance and exceptional resistance to abrasives, due to the floating stack design. An excellent choice for residential
MGP/MGPS Series SPECIFICATIONS
The MGP/MGPS Booster Pumps are the most durable booster pump available. The proven SignaSeal floating impeller design minimizes thrust loads allowing for continuous operation without damage to motor bearings,
ELECTRIC SUBMERSIBLE. ESP Pumping Systems. franklin-energy.com
ELECTRIC SUBMERSIBLE ESP Pumping Systems franklin-energy.com ESP Pumping Systems Franklin Electric s submersible pumps feature proven hydraulic components. Designed for marginal oil and gas wells, our
CENTRIFUGAL PUMPS CLOSE-COUPLED 9" FEATURES SPECIFICATIONS APPLICATIONS
FEATURES Volute: Heavy-duty cast iron construction; back pullout design; can be rotated for ease of installation Impeller: Enclosed, cast iron design for high efficiency; hydraulically balanced for reduced
MOTOR SPEED PRODUCT LINE: CAST IRON PUMPS TABLE OF CONTENTS SERIES DESCRIPTION RELATED PRODUCTS OPERATING RANGE. Section 1442 Page 1442.
Page 1442.1 TABLE OF CONTENTS Features & Benefits...2 Standard Materials of Construction...2 Specifications...2 Model Number Key...3 Cutaway View & Pump Features...3 Dimensions C, F, FH Sizes...4 Dimensions
Model 133 Models 134 & 135 AURORA 130 SERIES SINGLE STAGE TURBINE TYPE PUMPS
Model Models 4 & AURORA 0 SERIES SINGLE STAGE TURBINE TYPE PUMPS WWW.AURORAPUMP.COM AURORA 0 SERIES Single Stage Turbine Type Pumps Capacities to 0 G.P.M. Heads to 700 Ft. Temperatures to F A Pioneer in
20EVP-A SERIES. Vertical In-Line Self-Priming Centrifugal Pumps for Petroleums and Solvents. Marlow Pumps. Marlow Pumps.
2EVP-A SERIES Vertical In-Line Self-Priming Centrifugal Pumps for Petroleums and Solvents PUMP: Heavy-duty cast iron construction, with 2 NPT female threaded, in-line suction and discharge ports. This
4" SUBMERSIBLE PUMP 4" SUBMERSIBLE PUMP. "GS" series. "ST" series. "SL" series. ST Series (stainless steel) SL Series (thermoplastic)
4" SUBMERSIBLE PUMP 4" SUBMERSIBLE PUMP ST / GS SERIES (stainless steel) SL SERIES (thermoplastic) The "ST / GS / SL" series are built with such precision that they provide a superior output for many years.
TECHNICAL BROCHURE B5-18SB R1 5SB, 7SB, 10SB & 18SB 5-18 GPM, ½ 1½ HP, 60 HZ SUBMERSIBLE PUMPS
TECHNICAL BROCHURE B5-18SB R1 5SB, 7SB, 1SB & 18SB 5-18, ½ 1½ HP, 6 HZ SUBMERSIBLE PUMPS FEATURES Abrasive Handling Construction: Impellers designed with flat wearing surface which provides effective sand
D/G-12 Series. Up to 8 gpm (30.3 l/min)
D/G-12 Series Up to 8 gpm (3.3 l/min) D/G-12 Vertical Applications The D/G-12 is specifically designed for vertical pumping installations such as machine tool cooling applications. D/G-12 shown with Hydra-Cell
Goulds High-Pressure Multi-Stage Pumps
Goulds 3311 High-Pressure Multi-Stage Pumps Goulds Model 3311 Multistage Pumps Designed for a Wide Range of High Pressure Services Goulds Model 3311 is a radial split, segmented ring multistage pump...
TC & FC SERIES CENTRIFUGAL PUMPS
TC & FC SERIES CENTRIFUGAL PUMPS Pro-Stainless Steel Series Centrifugal Pumps The Webtrol Pro-Stainless Steel Series Centrifugal are designed for dependable performance and rugged continuous duty service.
4 5 GPM 7 GPM 10 GPM 15 GPM 20 GPM 30 GPM 35 GPM 55 GPM 95 GPM
PRO SERIES STAINLESS STEEL SUBMERSIBLE S 4 5 GPM 7 GPM 0 GPM 5 GPM 20 GPM 30 GPM 35 GPM 55 GPM 95 GPM SPECIFICATIONS Capacity: 5 to 20 GPM Heads: Up to 200 Feet 3450 RPM - 60 HZ Recommended for Clean Water
RSV In-Line Vertical Multi-Stage, Ring Section Pumps
RSV In-Line Vertical Multi-Stage, Ring Section s Technical Specification Pages RSV In-Line Vertical Multi-Stage, Ring Section This page left intentionally blank. RSV In-Line Vertical Multi-Stage, Ring
SUBMERSIBLE PUMPS 6" STAINLESS STEEL SR SERIES FEATURES
FEATURES Stainless steel impellers and diffusers to resist corrosion Heavy-duty stainless steel shell assures permanent alignment of all components to increase longevity and enables higher pressures than
Pipe connection All pump types have a treaded pipe connection: Rp2 1/2 for 6 WPS 16 N, Rp 3 for 6 WPS 30 N and Rp 4 for 6 WPS 45 N and 6 WPS 60 N.
All the internal and external metal components of the 6 WPS N pumps are constructed of stainless steel AISI 316 throughout and are being cold pressed from stainless steel sheet. 6 WPS N submersible pumps
Flow Range Horsepower Best Eff. Discharge Minimum Rotation➀ GPM Range GPM Connection Well Size 5LS " CCW " CCW
6 Hz LS EXTENSION 4" Submersible Pumps MODEL LS 5LS, 7LS, LS, LS, 8LS, 25LS FEATURES Powered for Continuous Operation: All ratings are within the working limits of the motor as recommended by the motor
Patent Pending. High Performance Self-Priming. Centrifugal Trash Pumps.
High Performance Self-Priming Centrifugal Trash Pumps www.gormanrupp.com A History of Innovation Gorman-Rupp has been revolutionizing the pumping industry since. Many of the innovations introduced by Gorman-Rupp
Pumps and Water Systems
Pumps and Water Systems U.S. 2010 List Prices Table of Contents A5817P 8-1-10 Description Page Description Page 4" Submersible Pumps A+ and S Series, PENTEK Fitted 2-4 T Composite Series, PENTEK Fitted
SUBMERSIBLE PUMPS 6" STAINLESS STEEL SR SERIES FEATURES SPECIFICATIONS APPLICATIONS
FEATURES n Stainless steel impellers and diffusers to resist corrosion n Heavy-duty stainless steel shell assures permanent alignment of all components to increase longevity and enables higher pressures
4SR 4 submersible pumps
4SR 4 submersible pumps PERFORMANCE RANGE Flow rate up to 375 l/min (22.5 m³/h) Head up to 405 m APPLICATION LIMITS Maximum liquid temperature +35 C Maximum sand content 150 g/m³ 100 m immersion limit
4SR 4 submersible pumps
4SR 4 submersible pumps PERFORMANCE RANGE Flow rate up to 375 l/min (22.5 m³/h) Head up to 405 m APPLICATION LIMITS Maximum liquid temperature +35 C Maximum sand content 150 g/m³ 100 m immersion limit
Nothing Better Top-of-the-line 4 submersible pump is unequalled in the marketplace. Stainless Steel
PREDATOR PLUS The Series 4 submersible pumps have a proven track record for reliability and performance, and are the preferred brand by many industry professionals. Stainless steel construction and self-lubricating
245 W. Roosevelt Road Building 12, Suite 83 West Chicago, IL
45 W. Roosevelt Road Building, Suite 83 West Chicago, IL 6085 800-33-448 www.aquamarkboosters.com AM-Q, AM-80V- & AM-80V-3 AM-00V & AM-50V Installation, Operation & Maintenance Manual AquaMark models:
High pressure centrifugal pumps
Series description H[ft] 5 5 4 8 Wilo-Multivert-MVIS 6 Hz - North America Q[m³/h] H[m] 5 4 MVIS 5 MVIS MVIS 5 5 4 6Q[US g.p.m.] 8 6 Pump series Wilo-Multivert MVIS 5..,.., 5.. Design Non-self priming multistage
TECHNICAL BROCHURE B45-70HB R2 45HB, 70HB HIGH PRESSURE CENTRIFUGAL BOOSTER PUMP
TECHNICAL BROCHURE B45-7HB R2 45HB, 7HB HIGH PRESSURE CENTRIFUGAL BOOSTER PUMP FEATURES Multi-Stage Design: This configuration provides a steady, quiet and vibration-free operation for years of trouble-free
Pump Specifications. LE50 Series ½ HP Submersible Sewage Pump
Pump Specifications LE50 Series ½ HP Submersible Sewage Pump LE50_P1 R11/16/2015 Copyright 2015 Liberty Pumps Inc. All rights reserved. Specifications subject to change without notice. LE50-Series Dimensional
Model and Series 115 VAC INDUSTRIAL DIAPHRAGM PUMPS. PumpAgents.com - buy pumps and parts online INDUSTRIAL DIAPHRAGM PUMPS
Model 31801 and 31800 Series 115 VAC INDUSTRIAL DIAPHRAGM PUMPS INDUSTRIAL DIAPHRAGM PUMPS FEATURES Run Dry Ability Self-Priming Thermal Overload Protected Motor Easy Installation Low Amp Draw Compact
Features: Applications: Irrigation. Commercial. Construction. Municipal. Mining
Frame Mount 7.5" BOOK: FMT-015 DATE: Mar. 1, 2012 Features: Volute: Ductile iron for heavy-duty service. Back pullout design. Can be rotated for ease of installation. Impeller: Enclosed design for high
FE Frame-Mounted End Suction Pumps. Leading The Flow. TACO.
FE Frame-Mounted End Suction Pumps Leading The Flow. TACO. Quiet, dependable power and proven performance. FE Series Pumps meet the latest standards for hydraulic performance and dimensional characteristics.
Vertical Multistage Pumps
Vertical Multistage Pumps Vertical multistage pumps are built intelligently for a variety of applications. The pump series classify as non-self priming centrifugal pumps with multiple stages to achieve
CE Close-Coupled End Suction Pumps. Leading The Flow. TACO.
CE Close-Coupled End Suction Pumps Leading The Flow. TACO. Quiet, dependable power and proven performance. CE Series Pumps meet the latest standards for hydraulic performance and dimensional characteristics.
ITT. Goulds Pumps. G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps. Engineered for life. Commercial Water.
ITT Goulds Pumps G&L Series SSH S & M-Group 316 Stainless Steel End Suction Pumps www.goulds.com Engineered for life A Full Range of Product Features Superior Materials of Construction: AISI Type 316L
Model Performance SW VersaJet. Shut-off PSI 118 Max. Lift 90 Conv. VersaJet Pro. Shut-off PSI 111 Max. Lift 90 Pro (RM2) Series
JET PUMPS Franklin s jet pumps can be configured for a variety of pressures and flow choices, and are Ideal for supplying fresh water to homes, cabins, farms, or practically anywhere that has a suction
Submittal Data 3450 RPM 60 Hertz JOB or CUSTOMER:
Redi-Flo4 Environmental Submersible Pumps 5E Submittal Data 3450 RPM 60 Hertz JOB or CUSTOMER: ENGINEER: CONTRACTOR: SUBMITTED BY: APPROVED BY: ORDER NO: SPECIFICATION REF: QUANTITY TAG NO. MODEL NO. GPM
UNIT TAG: TYPE OF SERVICE: SUBMITTED BY: APPROVED BY: ORDER NO.: UP B5. Circulator pumps. Motor Data Flow: Head: Efficiency: Pump Data
Submittal Data PROJECT: REPRESENTATIVE: ENGINEER: CONTRACTOR: UNIT TAG: TYPE OF SERVICE: SUBMITTED BY: APPROVED BY: ORDER NO.: UP 15-18 B5 Circulator pumps QUANTITY: DATE: DATE: DATE: Product photo could
Submersible Turbine Pumps
Submersible Turbine Pumps FW54 62 Supersedes NEW 5 to GPM For 5, 6, 7 and 8 inch wells High capacity submersible pumps for commercial, industrial, agricultural, municipal and other deep well, large water
OVIM/OVIMF. OVIM 60Hz OVIMF 60Hz. A New Vision for Quality Pumps. Light Vertical Multistage Centrifugal Pumps
OVIM/OVIMF A New Vision for Quality Pumps OVIM 60Hz OVIMF 60Hz Light Vertical Multistage Centrifugal Pumps PERFORMANCE SCOPE OVIM/OVIMF PRODUCT RANGE OVIM OVIM2 OVIM3 OVIM4 OVIM8 OVIM6 OVIM32 OVIM42 OVIM65