EB and ER Construction

Size: px
Start display at page:

Download "EB and ER Construction"

Transcription

1 EB and ER Construction EB Element EB elements are suited to slow speed applications having moderate starting and stopping loads. They are used as slip clutches and tension brakes for lighter torque and horsepower applications. EB elements are similar in design and construction to the CB elements and have many of the CB features. A neoprene rubber and cord tube is bonded on its inside diameter to a cylindrical surface. Friction shoes are attached with pins and held in position with lockwires to the outside diameter of the tube. Torque is transmitted by the sidewalls of the rubber tube. Pressurizing the tube forces the friction shoes to engage an inside drum diameter. The expanding design allows the element to behave as a centrifugal clutch. The radial stiffness of the rubber tube determines the element speed at which the friction shoes will retract. The rubber tubes of the three small elements are bonded to the outside diameters of solid hubs, which, in turn, are bored and keyseated for direct shaft mounting. The pressurizing passage can be either a radial hole thru the hub or a port provided in the hub face. Larger element sizes are attached to the shaft by a separate element hub. Element torque is dependent upon the applied pressure and speed. Catalog ratings are given at 75 psi (5,2) and zero rpm. Maximum recommended pressure is 110 psi (7,6 bar). Adjustment for operating pressure and speed is explained under Selection Procedure. EB elements are available in 11 sizes. They are identified by the inside drum diameter in inches to which they expand and the width in inches of their friction lining. For instance, size 16EB475 is designed to expand to a 16 inch diameter drum and has a friction lining width of 4.75 inches. The smallest EB element will expand to a 4 inch (102 mm) diameter drum and the largest to a 24 inch (610 mm) diameter drum. Due to its small diameter, the 4EB125 does not have replaceable friction shoes. Instead, the friction material is bonded to its rubber tube. Construction of the ER element is similar to the EB element, except for friction shoes. ER elements engage their drums directly with the outside rubber surface of their actuating tubes. This interface results in a friction force which provides a large torque in a relatively small package. It also provides electrical isolation between connecting shafts. ER Element ER elements are used as shaft couplings or holding brakes where engagement occurs at zero speed differential between element and drum. They are ideal for applications in which a disconnect is required without stopping the prime mover or in which the driving and or driven equipment must be frequently withdrawn from the drive. ER elements are identified similar to the EB elements. They are available in ten sizes. The smallest expands to a 3 inch (51 mm) diameter drum and the largest to a 24 inch (610 mm) diameter drum. Where Used: Centrifuges Core Expanders Laundry Machines Textile Machines Tire Building Machines C-24

2 EB Components Descriptions thru 24 EB Elements 6 7 4,6&8EBElements Torque 4EB ,1 6EB EB EB EB EB EB EB EB EB EB Torque 3ER ,2 6ER ER ER ER ER ER ER ER ER Item Component Description 1 Rim or hub and tube assembly 2 Elbow assembly 3 Air connection tube 4 Air connection gasket 5 Friction shoe 6 Shoe pin 7 Lockwire 8 Pipe plug 5,6,7 Friction shoe, pin and lockwire kit C-25

3 FormEB701 EB Elements DimensionalandTechnicalData s4to8 D 2 O 4 V W Q O H 6 D 1 D 24 H 13 H 2 psi Dimensions in inches 4EB / / EB / / EB / / Min. Max. No. No. Width Number Torque Bore Range D 1 D 2 D 24 H 2 H 6 H 13 L O O Q 4 (Deg) V W Min. Max. No. No. Width 4EB , / / , EB / / , EB / / , bar Dimensions in psi rpm psi/rpm 2 lb ft 2 lb in 2 inches in 3 in 4EB * EB EB Number Torque Maximum Speed C s Centrifugal Gain 4EB , * 0,004 1,0 84 0, EB ,1 0,11 3, , EB ,1 0,45 8, , New Worn Wk 2 Weight Lining bar Friction Area New Worn Air Tube Cavity Maximum Diameter rpm bar/rpm 2 kg m 2 kg cm 2 millimeters dm 3 mm Referstobasicpartnumberonly.Whenordering, itmustbespecifiedwhichairentryhole,ooro 4 is tobeused. Dynamictorqueshown,statictorqueapproximately25%greater.Torqueineachapplicationis dependentuponairpressureandspeed. AmericanNationalStandardforUnifiedScrew Threads. AmericanNationalPipeThread Baseduponminimumbores. Liningmoldedintorubbertube.Completeelement shouldbereplacedwhendimensionh 6 iswornto 3.88in(98mm)diameter. contactwithwornshoes. CopyrightEatonCorporation,1997,Allrightsreserved. C-26

4 EB Element Form EB 702 Technical Data s 9 to 24 rpm psi/rpm 2 lb ft 2 lb in 2 inches in 3 in 9EB E EB E EB E EB E EB E EB E EB E EB E New Worn Number Torque Maximum C s Wk 2 Weight Speed Centrifugal Friction Max.Air Max. Gain Area Lining Thickness Cavity Diameter New Worn 9EB ,1 E-06 0,042 4, , EB ,2 E-06 0,042 4, , EB ,2 E-06 0,126 7, , EB ,3 E-06 0, , EB ,4 E-06 0, , EB ,7 E-06 0, , EB ,9 E-06 1, , EB ,4 E-06 1, , rpm bar/rpm 2 kg m 2 kg cm 2 millimeters dm 3 mm Refers to basic part number only. Dynamic torque shown, static torque approximately 25% greater. Torque in each application is dependent upon air pressure and speed. Tolerances for sizes: 9 thru / in (0,13/-0,00 mm) 16 thru / in (0,25/-0,00 mm) contact with worn shoes. C-27

5 EB Elements Form EB 702 Dimensional Data s 9 to 24 O 3 V D 2 W L Q D 24 H 2 D 25 H 6 H 13 G H 7 Dimensions in inches 9EB EB EB EB EB EB EB EB No. Dia. No. Width Number Torque D 2 D 24 D 25 G H 2 H 6 H 7 H 13 L O Q 3 (Deg) V W No. Dia. No. Width 9EB , , EB , , EB , , EB , , EB , , EB , EB , , EB , , Dimensions in millimeters C-28

6 EB Clutch Application Forms EB 705 and 706 Coupling Mounting ArrangementDimensional Data s 6 to 12 D Shafts and keys by customer. Refer to component D 6 D D 45 Element D 6 D 45 Element B3 Rotorseal O Hub Element Hub O Hub D 1 X D 7 M D 1 M X D 7 H s 6 and 8 Form EB705 D 37 D 38 C.G. Element C.G. & Hub s 10 and 12 Form EB706 D 37 D 38 C.G. Element & Hub C.G. & Hub lb Dimensions in inches 6EB EB EB EB Number Torque Weight Min. Max. Bore Range MIn. Max. D D 1 D 6 D 7 D 37 D 38 D 45 H M O X 6EB EB EB EB kg Dimensions in millimeters Refer to Rotorseal Section for mounting and dimension information. For larger sizes, it is recommended that the E product line be used. See Form E604. Refers to basic part number only and does not include the rotorseal and hose. Dynamic torque shown, static torque approximately 25% greater. Torque in each application is dependent upon air pressure and speed. Based upon minimum bores. Rotorseal and hose not included. C-29

7 EB Clutch Application Forms EB 707 and 708 Bearing Arrangement Dimensional Data s 6 to 12 Shaft and keys by customer. Refer to component catalog pages for component details. D 6 D D 45 D30 B3 Rotorseal O M D 1 D D 6 D D 7 D 30 H Element O M D 7 D (6.4 mm) Bearing Mounted Hub H Element Hub D 40 s 6 and 8 Form EB707 C.G. s 10 and 12 Form EB708 C.G. D 40 lb Dimensions in inches 6EB EB EB EB Number Torque Weight Min. MIn. Bore Range Max. Max. D D 1 D 6 D 7 D 30 D 40 H MAX M O 6EB , EB , EB , EB , kg Dimensions in millimeters Refer to Rotorseal Section for mounting and dimension information. For larger sizes, it is recommended that the E product line be used. See Form E604. Refers to basic part number only and does not include the rotorseal and hose. Dynamic torque shown, static torque approximately 25% greater. Torque in each application is dependent upon air pressure and speed. Based upon minimum bores. Rotorseal and hose not included. C-30

8 EB Brake Application Forms EB 709 and 710 Dimensional Data s 6 to 12 Shaft, key, and reaction members by customer. Refer to component catalog pages for component details. D 45 D 6 D D 45 D 6 D Element Hub Hub D 9 D 7 H D 9 D 7 H s6&8 Form EB 709 C.G. & Hub D 38 s 10 & 12 Form EB710 C.G. & Hub D 38 lb Dimensions in inches 6EB EB EB EB Number Torque Weight Min. MIn. Bore Range Max. Max. D D 6 D 7 D 9 D 38 D 45 H 6EB EB EB EB kg Dimensions in millimeters Refers to basic part number only. Dynamic torque shown, static torque approximately 25% greater. Torque in each application is dependent upon air pressure and speed. Based upon minimum bores. C-31

9 ER Elements Form ER 703 Dimensional and Technical Data s 3 to 8 O 4 V D 2 W Q O D 24 D 1 H 6 H 13 H 2 L Dimensions in inches 3ER NA NA NA NA 0.38 NA NA ER / / ER / / Min. Max. No. Depth Number Torque Bore Range D 1 D 2 D 24 H 2 H 6 H 13 L O O Q 4 (Deg) V W Min. Max. No. Depth 3ER , NA NA NA NA 10 NA NA ER / / ER / / Dimensions in millimeters rpm lb ft 2 lb in 3 in 3ER ER ER Number Torque Maximum Speed Wk 2 Weight Maximum Air Cavity 3ER , ,001 0,5 0,07 78 Maximum Diameter 6ER ,004 3,2 0, ER ,02 8,2 0, rpm kg m 2 kg dm 3 mm Refers to basic part number only. When ordering, it must be specified which air entry hole, O or O 4 is to be used. Static torque. American National Standard for Unified Screw Threads. American National Pipe Thread contact with worn shoes. Based upon minimum bores. This element has six equally spaced rubber pads on the tube diameter instead of circumferential grooves. C-32

10 ER Elements Form ER 704 Technical Data s 10 to 24 rpm lb ft 2 lb in 3 in 10ER ER ER ER ER ER ER Wk 2 Weight Air Number Torque Maximum Speed 10ER ,03 3,6 1, ER ,08 5,9 1, ER ,17 7,7 1, ER , , ER , , ER , , ER , , Tube Cavity Maximum Diameter rpm kg m 2 kg dm 3 mm Refers to basic part number only. Static torque. contact with worn shoes. C-33

11 ER Elements Form ER 704 Dimensional Data s 10 to 24 O 3 V D 2 W L Q D 24 H 2 D 25 G H 6 H 13 H 7 Dimensions in inches 10ER ER ER ER ER ER ER No. Dia. Number Torque D 2 D 24 D 25 G H 2 H 6 H 7 H 13 L O 3 Q V W No. Dia. 10ER , ER , ER , ER , ER , ER , ER , Dimensions in millimeters C-34

12 ER Coupling Application Form ER 716 Dimensional Data s 6 and 8 D D 6 D 45 O B3 Rotorseal Element Hub H M X D 1 D 7 Shafts and keys by customer lb Dimensions in inches 6ER ER Torque Weight D D 1 D 6 D 7 D 45 H M O X 6ER ER kg Dimensions in millimeters Refer to Rotorseal Section for mounting and dimension information. Static Torque. Based on minimum bores. C-35

13 ER Coupling Application Form ER 717 Dimensional Data s 10 to 24 D D 6 D 45 O Element B3 Rotorseal D 1 M Hub X D 7 H Element Hub Shafts and keys by customer lb Dimensions in inches 10ER ER ER ER ER ER ER Torque Weight Min. Min. Bore Range Max. Max. D D 1 D 6 D 7 D 45 H M O X 10ER ER ER ER ER ER ER kg Dimensions in millimeters Refer to Rotorseal Section for mounting and dimension information. Static torque. Based upon minimum bores. C-36

14 EB and ER Mounting Components Form EB 711 Element Hub Dimensional and Technical Data s 10 to 24 D 7 D 29 D 42 or tapped holes H 14 H 11 lb lb ft 2 Dimensions in inches 10EB&ER EB&ER EB&ER EB&ER EB&ER EB&ER EB&ER Number Weight Wk 2 D 7 D 29 D 42 H 11 H 14 10EB&ER ,4 0, EB&ER , EB&ER , EB&ER , EB&ER , EB&ER , EB&ER , kg kg m 2 Dimensions in millimeters Based upon minimum bores. C-37

15 Form EB 712 EB and ER Mounting Components Hub for Non-Ventilated Internal Flange Dimensional and Technical Data s 6 to D 42 D 7 or tapped holes H 11 H 14 lb lb ft 2 Dimensions in inches 6EB&ER EB&ER250 N/A EB&ER EB&ER EB&ER EB&ER EB&ER EB&ER EB&ER Number Weight Wk 2 D 7 D 42 H 11 H 14 6EB&ER ,4 0, EB&ER250 N/A ,2 0, EB&ER ,2 0, EB&ER , EB&ER , EB&ER , EB&ER , EB&ER , EB&ER , kg kg m 2 Dimensions in millimeters Based upon minimum bores. C-38

16 Form EB 713 EB Mounting Components Hub for Ventilated Internal Flange Dimensional and Technical Data s 6 to 12 D 7 or tapped holes D 28 D 42 H 11 H 14 lb lb ft 2 Dimensions in inches 6EB EB EB EB Number Weight Wk 2 D 7 D 29 D 42 H 11 H 14 6EB ,2 0, EB ,8 0, EB ,2 0, EB , kg kg m 2 Dimensions in millimeters Based upon minimum bores. C-39

17 Form EB 714 EB Mounting Components Ventilated Internal Flange Dimensional and Technical Data s 6 to 12 D 6 or tapped holes D 31 H 9 1 H lb lb ft 2 Dimensions in inches 6EB /8-16 8EB / EB / EB /2-13 Number Weight Wk 2 D 6 D 31 1 H H 9 L No. No. 6EB ,0 0, , /8-16 8EB ,3 0, , / EB , , / EB , , /2-13 kg kg m 2 Dimensions in millimeters Tolerance / in (0,13/-0,00 mm) American National Standard for Unified Screw Threads. C-40

18 Form EB 715 EB and ER Mounting Components Non-Ventilated Internal Flange Dimensional and Technical Data s 6 to 24 D 6 L D 31 H H 9 1 Tolerance / in (0,08/-0.00 mm) American National Standard for Unified Screw Theads lb lb ft 2 Dimensions in inches 6EB&ER /8-16 8EB&ER / EB&ER / EB&ER / EB&ER / EB&ER / EB&ER / EB&ER / EB&ER /4-10 Number Weight Wk 2 D 6 D 31 1 H H 9 L No. No. 6EB&ER ,5 0, , /8-16 8EB&ER ,8 0, , / EB&ER , , / EB&ER , , / EB&ER , , / EB&ER , , / EB&ER , , / EB&ER , , / EB&ER , , /4-10 kg kg m 2 Dimensions in millimeters C-41

E and VE Construction

E and VE Construction E and VE Construction E Element VE Element Type E and VE elements combine rugged design and rigid construction features which make them ideal for moderate to heavy duty clutch and brake service. They are

More information

and zero rpm. Maximum recommended pressure is 110 psi (7.6 bar). Adjustment for speed is explained under Selection Procedure.

and zero rpm. Maximum recommended pressure is 110 psi (7.6 bar). Adjustment for speed is explained under Selection Procedure. CB Construction Single Flange Dual Flange The type CB element assembly is designed and built to provide dependable clutch or brake service in the most exacting industrial applications. It is suited to

More information

Airflex CB Construction Section B

Airflex CB Construction Section B Airflex CB Construction Single Flange Element Dual Flange Element The type CB element assembly is designed and built to provide dependable clutch or brake service in the most exacting industrial applications.

More information

Constricting Type Clutches and Brakes

Constricting Type Clutches and Brakes Constricting Type Clutches and Brakes B Constricting Features B-1 Element Descriptions B-3 CB Elements B-5 Technical and Dimensional Data B-9 Clutch and Brake Applications B-15 Mounting Components B-40

More information

Caliper Disc Brakes. Description H-1. Technical Data and Selection Procedure H DP100 Caliper H-4. HC3 and HD3 Calipers H-7

Caliper Disc Brakes. Description H-1. Technical Data and Selection Procedure H DP100 Caliper H-4. HC3 and HD3 Calipers H-7 Eaton Corporation Airflex Division 9919 Clinton Road Cleveland, Ohio 44144-1077 Caliper Disc Brakes H Phone (216) 281-2211 Fax: (216) 281-3890 Description H-1 Technical Data and Selection Procedure H-2

More information

Airflex Spring Applied Brakes

Airflex Spring Applied Brakes Airflex Spring Applied Brakes CS and CSA Brake Elements... 232 Technical and Dimensional Data... 233 Applications... 235 Component Parts... 237 CTE Brake Elements... 239 Technical and Dimensional Data...

More information

Airflex. Airflex DBB & DBA Brakes

Airflex. Airflex DBB & DBA Brakes 36191_12pg Covers 8/11/03 6:06 PM Page 01 Airflex Airflex DBB & DBA Brakes These spring-applied, pressure released, disc style brakes develop equal torque in either direction of rotation. Their torque

More information

Constricting Type Clutches and Brakes

Constricting Type Clutches and Brakes Eaton Corporation Airflex Division 9919 Clinton Road Cleveland, Ohio 44144-1077 Phone (216) 281-2211 Fax: (216) 281-3890 Constricting Type Clutches and Brakes Constricting Features B-1 Element Descriptions

More information

Airflex Air Cooled Disc Clutches and Brakes

Airflex Air Cooled Disc Clutches and Brakes Airflex Air Cooled Disc Clutches and Brakes DBA Description... 183 DBA Brake Elements... 185 DBA Technical information... 186 DBB and DBBS Description... 187 DBB Brake Elements... 189 DBB Technical Information...

More information

Airflex Clutches and Brakes for Oil & Gas

Airflex Clutches and Brakes for Oil & Gas Airflex Clutches and Brakes for Oil & Gas October 2013 2008 Eaton Corporation. All rights reserved. Airflex Overview and History Leading Manufacturer of Industrial Clutches and Brakes Make-to-order business

More information

Airflex. Airflex CBC Clutch/Brake Combination. Today s answer for high cyclic, heavy-duty industrial applications. Authorized Distributor

Airflex. Airflex CBC Clutch/Brake Combination. Today s answer for high cyclic, heavy-duty industrial applications. Authorized Distributor Airflex Airflex CBC Clutch/Brake Combination Today s answer for high cyclic, heavy-duty industrial applications. Authorized Distributor 26255 Groesbeck Hwy. Warren, MI 48089 U.S.A. 586.775.3000 586.775.3040

More information

Type CH Hydraulic Elements

Type CH Hydraulic Elements Type CH Hydraulic Elements Element Description Type CH Type CH elements are designed specifically for heavy duty clutch and brake applications. They can be air or hydraulically actuated. The friction disc

More information

PSI Series Features: Trouble-free design for long life. Simple mechanical actuation

PSI Series Features: Trouble-free design for long life. Simple mechanical actuation CROSSOVER DRIVES Wrap Spring Clutches Ideal for Overrunning, Start- Stop, and Single Revolution Applications The Crossover Drives clutches are the basic form of wrap spring clutch design. For start-stop

More information

Airflex Rotorseal Description

Airflex Rotorseal Description Airflex Rotorseal The Airflex rotorseal is a rotary union (rotary joint) which permits the transfer of gases or liquids, under pressure or vacuum, into or out of the exposed end of a rotating shaft or

More information

Installation, Operation and Maintenance of the Airflex Model EB and ER Element Assemblies

Installation, Operation and Maintenance of the Airflex Model EB and ER Element Assemblies EB 7000 Warning Forward this manual to the person responsible for nstallation, Operation and Maintenance of the product described herein. Without access to this information, faulty nstallation, Operation

More information

AMCB AccuStop TM. Clutch/Brake Combination Section F

AMCB AccuStop TM. Clutch/Brake Combination Section F Clutch/Brake Combination The Airflex AMCB AccuStop clutch/brake combination consists of an air-actuated disc clutch and a spring-applied disc brake. Engineered for small-to-medium tonnage ( to 0 ton),

More information

Pin-guided clutch with three flyweights

Pin-guided clutch with three flyweights S-Type Pin-guided clutch with three flyweights Construction and mode of operation 2 5 4 3 3 1 1 5 2 6 4 = Hub = Flyweights = Cylindrical pin = Tension spring = Lining = Clutch drum / Cover disc Low noise

More information

MAXITORQ ELECTRICALLY ACTUATED CLUTCHES AND BRAKES

MAXITORQ ELECTRICALLY ACTUATED CLUTCHES AND BRAKES MAXITORQ ELECTRICALLY ACTUATED CLUTCHES AND BRAKES HOW TO SELECT THE CORRECT CLUTCH OR BRAKE The easiest way is to ask our application engineers. For clutch application, we need to know: Torque or H.P.

More information

Air Tube Disc Clutches and Brakes

Air Tube Disc Clutches and Brakes Air Tube Disc Clutches and rakes Low Inertia and Very Low Inertia Clutches and rakes Very Low Inertia Drive Plate Assembly with onded or Riveted Pads Ring Shims Multiple Spud Airtube Pressure Plate Floating

More information

Serving Industrial Markets Since 1961:

Serving Industrial Markets Since 1961: Full Line Brochure Clutches Brakes Clutch Brakes Caliper Brakes & Rotors Torque Limiters Air Shaft Seals Sheaves Serving Industrial Markets Since 1961: Food Processing & Packaging Material Handling Printing

More information

Air Champ DPC-9T & DPC-11T Static Torque in Inch-Pounds. Air Pressure in PSI

Air Champ DPC-9T & DPC-11T Static Torque in Inch-Pounds. Air Pressure in PSI CLUTCHES DPC SERIES DUAL PLATE CLUTCHES This Series, specified by component, allows you to custom design for specific application requirements: Static Torque capacity up to 36,000 In. Lbs. @ 80 psi Maximum

More information

Clutch Couplings FW/FWW. Overrunning Ball Bearing Supported, Sprag Clutch Couplings. FW Series. FWW Series. Typical Applications

Clutch Couplings FW/FWW. Overrunning Ball Bearing Supported, Sprag Clutch Couplings. FW Series. FWW Series. Typical Applications s Overrunning Ball Bearing Supported, Sprag s Series For in-line shaft applications Outer race overrunning intermediate speed Inner race overrunning high speed clutch couplings are comprised of an FSO

More information

Airflex Floating Housing Brake

Airflex Floating Housing Brake Airflex Floating Housing Brake Airflex FHB Brake Elements Dimensional & Technical Data Overview Eaton Airflex has introduced a revolutionary new design in disc brake technology called the Floating Housing

More information

Air Champ RPM DPC-15T DPC-13T DPC-11T DPC-11T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T

Air Champ RPM DPC-15T DPC-13T DPC-11T DPC-11T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DPC-9T DUAL PLATE FRICTION CLUTCH SELECTION CHART Friction clutch recommendation is based upon air pressure of 50 psi, transmitted horsepower and speed. RPM 100 200 300 400 500 600 700 800 900 1000 1100 1200

More information

NLS Centrifugal Clutches

NLS Centrifugal Clutches Centrifugal Clutches Section Contents Centric Centrifugal Clutches CCC Series FEATURES... 76 OPERATING PRINCIPLES... 77 SELECTION... 77 Type A Standard... 79 Type AVL Vertical Lift Out... 80 Type H Pulley

More information

for Installation, Operation and Maintenance of Airflex VC Element Assemblies VC 5000

for Installation, Operation and Maintenance of Airflex VC Element Assemblies VC 5000 5000 Warning Forward this manual to the person responsible for Installation, Operation and Maintenance of the product described herein. Without access to this information, faulty Installation, Operation

More information

Bore (B) Pitch Diam. Drilling Template Flanges (1) Diam of Diam of. Groove. Neck D X G A Raised Face Raised Face P Raised face

Bore (B) Pitch Diam. Drilling Template Flanges (1) Diam of Diam of. Groove. Neck D X G A Raised Face Raised Face P Raised face Class 300 Orifice s Pipe size Thickness of Depth of jack Jack screw s (1) screw slot size & of and raised face Hub Bevel threaded Length of of Stud stud bolts Face face face bolt circle Bolts Bolts Bolt

More information

DEPARTMENT OF MECHANICAL ENGINEERING Subject code: ME6601 Subject Name: DESIGN OF TRANSMISSION SYSTEMS UNIT-I DESIGN OF TRANSMISSION SYSTEMS FOR FLEXIBLE ELEMENTS 1. What is the effect of centre distance

More information

Tooth Clutches. Series 5H and 55H-P Pressure Applied Tooth Clutch. Stationary Cylinder for Dry Operation or in Oil. Series 5H and 55H-P

Tooth Clutches. Series 5H and 55H-P Pressure Applied Tooth Clutch. Stationary Cylinder for Dry Operation or in Oil. Series 5H and 55H-P Series 5H and 55H-P Series 5H and 55H-P Pressure Applied Tooth Clutch Stationary Cylinder for Dry Operation or in Oil Features Tooth clutch gives positive drive with no slip Shielded bearings need no lubrication

More information

INSTRUCTION MANUAL IM-118. for. HYDRAULIC HUB INSTALLATION and REMOVAL

INSTRUCTION MANUAL IM-118. for. HYDRAULIC HUB INSTALLATION and REMOVAL No Revision June 1, 1999 Revision A Jan. 11, 2000 page 1 INSTRUCTION MANUAL IM-118 for HYDRAULIC HUB INSTALLATION and REMOVAL The Riverhawk Company reserves the right to make changes updating this document

More information

Section 15 Unit Selection Procedures

Section 15 Unit Selection Procedures APC-2006 All Products Catalog Section 15 Unit Selection Procedures Main Office and Manufacturing Plant 3660 Dixie Highway Fairfield, Ohio 45014 Telephone: (513) 868-0900 Fax: (513) 868-2105 E-Mail: info@forcecontrol.com

More information

Modern Auto Tech Study Guide Chapter 65 & 66 Pages Tires, Wheels, Bearings 51 Points. Automotive Service. Danger of Old Tires!!

Modern Auto Tech Study Guide Chapter 65 & 66 Pages Tires, Wheels, Bearings 51 Points. Automotive Service. Danger of Old Tires!! Modern Auto Tech Study Guide Chapter 65 & 66 Pages 1241 1278 Tires, Wheels, Bearings 51 Points Automotive Service Danger of Old Tires!! Tires Manufactured Since 2000 Since 2000, the week and year the tire

More information

Advantages of a Magnetically Driven Gear Pump By Steven E. Owen, P.E.

Advantages of a Magnetically Driven Gear Pump By Steven E. Owen, P.E. Advantages of a Magnetically Driven Gear Pump By Steven E. Owen, P.E. Introduction Before considering a magnetically driven pump for use in a fluid system, it is best to know something about the technology

More information

Easy Access with Removable Cover Panel

Easy Access with Removable Cover Panel Mistral Brakes Modular design permits variable tensioning capacities! Wichita Clutch s Mistral pneumatic tension brakes are ideally suited to the needs of the corrugating market for which it was originally

More information

Braking System Layout

Braking System Layout The Braking System The energy used to accelerate or move a vehicle from rest to a certain speed is called Kinetic i (moving) energy. To slow the vehicle down, this kinetic energy must be converted or changed,

More information

Media Number -SENR Publication Date -01/10/1977 Date Updated -12/10/2001

Media Number -SENR Publication Date -01/10/1977 Date Updated -12/10/2001 - - 55, 56, 57, 58 & 59 TOWING WINCHES Page 1 of 21 Testing and Adjusting 55, 56, 57, 58 & 59 TOWING WINCHES Media Number -SENR7217-01 Publication Date -01/10/1977 Date Updated -12/10/2001 Testing And

More information

TORQUE LIMITER SERIES 600. Airjustor

TORQUE LIMITER SERIES 600. Airjustor TORQUE LIMITER SERIES 600 Airjustor Quality and Autogard are synonymous with overload protection. The Company's reputation for high quality products is derived from over 40 years of design, innovation

More information

Installation Operation Maintenance. LSSN Butterfly Valve AGA Approved 50MM - 150MM. QAD#IM6055.REVA

Installation Operation Maintenance. LSSN Butterfly Valve AGA Approved 50MM - 150MM.  QAD#IM6055.REVA LSSN Butterfly Valve Installation Operation Maintenance Licence Number: 5326 www.challengervalves.com.au 1 Index 1. INTRODUCTION 1.1 Design Features 3 1.2 Flange and Pipe Compatibility 4 1.3 Operating

More information

Introduction to Armature Actuated Brakes (AAB) Operating Principle. Engaged Condition (power off) Disengaged Condition (power on)

Introduction to Armature Actuated Brakes (AAB) Operating Principle. Engaged Condition (power off) Disengaged Condition (power on) Introduction to Armature Actuated Brakes (AAB) The Armature Actuated Brakes are spring-set, electrically released, friction devices, which develop holding and braking torque in the absence of electrical

More information

1008 thru 3030 sizes. C Hub Dia. Short No. Std. Hex Capacity. Key u. F Wrench D Steel Qty. Size Install.

1008 thru 3030 sizes. C Hub Dia. Short No. Std. Hex Capacity. Key u. F Wrench D Steel Qty. Size Install. TAPER-LOCK ings - Dimensions PT6-3 1008 thru 3030 sizes DIMENSIONS FOR 1008 THRU 3030 TAPER-LOCK BUSHINGS RATINGS (Lb-in) C Hub Dia. F L M Wrench Torque A B D Std. Short Short No. Torque CL 30 Std. Hex

More information

DRUM BRAKE RIMS Periodic inspection of drum brake rims is necessary to determine indications of uneven or excessive wear. In general, brake rim failures other that regular wear are caused by brake linings

More information

Precision Modules PSK

Precision Modules PSK Precision Modules PSK The Drive & Control Company Rexroth Linear Motion Technology Ball Rail Systems Roller Rail Systems Standard Ball Rail Systems Super Ball Rail Systems Ball Rail Systems with Aluminum

More information

FLANGE. Flanges used for

FLANGE. Flanges used for FLANGE FLANGE Flanges with rating class designations 150, 300, 400, 600, 900, 1500, and 2500 in sizes NPS 1 2 through NPS 24 ASME B16.5: Pipe Flanges and Flanged Fittings (NPS 24 ) ASME B16.47: NPS 26

More information

Stainless Steel Couplings, Universal Joints & Shaft Accessories

Stainless Steel Couplings, Universal Joints & Shaft Accessories Stainless Steel Couplings, Universal Joints & Shaft Accessories E SSFC Series - Insert (3 Jaw) Type Coupling 316 stainless steel with passivated finish Precision machined bore or solid hubs Three types

More information

Catalog HY /NA. Catalog HY /NA. Parker Hannifin Corporation Hydraulic Pump Division Marysville, Ohio USA

Catalog HY /NA. Catalog HY /NA. Parker Hannifin Corporation Hydraulic Pump Division Marysville, Ohio USA Catalog HY28-6/NA PV, PVT Series Piston Pumps Variable Volume Catalog HY28-6/NA 1 Catalog HY28-6/NA Notes Series PV 2 Catalog HY28-6/NA Introduction Series PV Quick Reference Data Chart Pump Delivery Approx.

More information

ROLLER CHAIN SPROCKETS INDEX...E-1 - E-2 MADE-TO-ORDER CAPABILITIES...E-3

ROLLER CHAIN SPROCKETS INDEX...E-1 - E-2 MADE-TO-ORDER CAPABILITIES...E-3 Index SECTION E ROLLER CHAIN PRODUCT PAGE INDEX...E- - E-2 MADE-TO-ORDER CAPABILITIES...E- SECTION I STANDARD...E-4 - E-2 Shear Pin Sprockets, Bolt-On...E-4 - E-6 Type D Sprockets, Detachable Hubs Split

More information

Precise controllability for severe, high energy or continuous slip applications

Precise controllability for severe, high energy or continuous slip applications Airflex Water Cooled Brakes Type WCB Type WCB Precise ctrollability for severe, high energy or ctinuous slip applicatis Airflex Water Cooled Brakes WCB and WCB Where used rilling rigs ynamometers Logging

More information

Primary Clutch/Brake Pin Drive, Spline Drive PCB-825, PCB-1000, PCB-1225 Primary Clutch/Brake Coupling PCBC-825, PCBC-1000, PCBC-1225

Primary Clutch/Brake Pin Drive, Spline Drive PCB-825, PCB-1000, PCB-1225 Primary Clutch/Brake Coupling PCBC-825, PCBC-1000, PCBC-1225 Primary Clutch/Brake Pin Drive, Spline Drive PCB-825, PCB-1000, PCB-1225 Primary Clutch/Brake Coupling PCBC-825, PCBC-1000, PCBC-1225 P-205 819-0474 Installation Instructions Contents Installation Instructions

More information

REMOVAL & INSTALLATION

REMOVAL & INSTALLATION REMOVAL & INSTALLATION REAR BRAKE CALIPER NOTE: For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any

More information

Shaft Mounted Speed Reducer Selection

Shaft Mounted Speed Reducer Selection GEARBOX SELECTION PROCEDURE (a) Service Factor From Table 1 select the service factor applicable to the drive. (b) Design Power Multiply the absorbed power (or motor power if absorbed power not known)

More information

TECHNICAL HANDBOOK. Heavy Duty ASME B73.1. Wilfley Sealing Technology. No Flush Water Required

TECHNICAL HANDBOOK. Heavy Duty ASME B73.1. Wilfley Sealing Technology. No Flush Water Required TECHNICAL HANDBOOK Heavy Duty ASME B73.1 A9 Wilfley Sealing Technology No Flush Water Required WILFLEY SEALING TECHNOLOGY Wilfley Sealing Technology is the premier sealing solution for the toughest pumping

More information

Section 9: Gearboxes: Series F

Section 9: Gearboxes: Series F GEARBOXES Section 9: Gearboxes: Series F The new Fenner Series F geared motor range is primarily designed as a compact shaft mounted unit incorporating an integral torque reaction bracket. ew range now

More information

CENTRIC CENTRIFUGAL CLUTCHES

CENTRIC CENTRIFUGAL CLUTCHES CCC SERIES SECTION CONTENTS FEATURES...76 OPERATING PRINCIPLES...77 SELECTION...77 AVAILABLE STYLES...78 AVAILABLE TYPES...80 OVERLOAD DETECTION...80 SELECTION GUIDE...81 Centric Clutches 75 CCC SERIES

More information

Industrial Clutch Products

Industrial Clutch Products Industrial Clutch Products MODEL CBA Air or Hydraulically Actuated Combination Clutch-Brakes INDUSTRIAL CLUTCH PRODUCTS 1 Model CBA Air or Hydraulically Actuated Combination Clutch-Brakes PERFORMANCE CHARACTERISTICS

More information

Installation, Operation and Maintenance of Airflex VC Grinding Mill Clutches

Installation, Operation and Maintenance of Airflex VC Grinding Mill Clutches VC 5001 Forward this manual to the person responsible for Installation, Operation and Maintenance of the product described herein. Without access to this information, faulty Installation, Operation or

More information

Section 9: Gearboxes: Series W

Section 9: Gearboxes: Series W GEARBOXES Section : 9 Section 9: Gearboxes: Series W A modular designed aluminium worm box available in a vast range of sizes and ratios for cost effective solutions. 9 s with ratings from 0.09 to 7.5kW

More information

SHAFT MOUNTED HELICAL GEAR REDUCER

SHAFT MOUNTED HELICAL GEAR REDUCER Shaft Mounted Helical Gear Assembly INTRODUCTION The VIGNESSH Shaft Mounted Helical Gear Units are the result of experience in design and production, taking advantage of the most recent relevent research

More information

HEVC Installation, operation and maintenance manual Airflex HEVC

HEVC Installation, operation and maintenance manual Airflex HEVC - Installation, operation and maintenance manual Airflex HEVC 5005 204261 General information Warning Forward this manual to the person responsible for Installation, Operation and Maintenance of the product

More information

Assortment 2013_FPT BOOK.indb /02/13 6:57 PM

Assortment 2013_FPT BOOK.indb /02/13 6:57 PM Assortment Contents Why compete against your supplier when you can be our partner Chain Tensioners...14 see Chains section for details Anti-Vibration Mounts...224 Key Steel...225 Motor Rails...226 Self

More information

Stearns Heavy Duty Clutches & Brakes... Rugged, Reliable

Stearns Heavy Duty Clutches & Brakes... Rugged, Reliable Stearns Heavy Duty Clutches & Brakes... Rugged, Reliable Stearns heavy duty clutches and brakes represent over 75 years of design, engineering and on-the-job experience. Stearns products are backed by

More information

SYNCHRONOUS BELT DRIVES

SYNCHRONOUS BELT DRIVES Experience The PTH-98 SYNCHRONOUS BELT DRIVES EMERSON POWER TRANSMISSION MORE HORSEPOWER PER DOLLAR... For Positive Performance, Choose... BROWNING Panther Synchronous Drive Systems. Todays Choice For:

More information

SPH Series GAM CAN, JUST ASK!

SPH Series GAM CAN, JUST ASK! SPH Series GAM CAN, JUST ASK! - Highest Precision Class The SPH is GAM s latest solution for today s demanding motion control challenges. Available in six frame sizes and nominal torque ratings ranging

More information

Troubleshooting The Transmission Hydraulic System

Troubleshooting The Transmission Hydraulic System 416B, 426B, 428B, 436B, & 438B BACKHOE LOADERS TRANSMISSION Testing And Adjusting Troubleshooting The Transmission Hydraulic System Make reference to the following warning and pressure tap locations for

More information

Tension Brakes/Very High Heat Capacity

Tension Brakes/Very High Heat Capacity Tension Brakes/Very High Heat apacity opper disc design for high heat dissipation External air and water connections Accurate control High Temperature O-Rings New friction material lasts longer with less

More information

4 Fenner Torque Drive Plus 3

4 Fenner Torque Drive Plus 3 Fenner Torque Drive Plus 3 offers; State of the art power ratings. Compact drive package - reduced weight. Quiet operation. Accuracy of positioning. Anti-static as standard. Runs on standard HTD pulleys.

More information

Installation, Operation and Maintenance of Airflex Model AMCB AccuStop TM Clutch\Brake Combination

Installation, Operation and Maintenance of Airflex Model AMCB AccuStop TM Clutch\Brake Combination AMCB 16200 Forward this manual to the person responsible for Installation, Operation and Maintenance of the product described herein. Without access to this information, faulty Installation, Operation

More information

Driver Driven. InputSpeed. Gears

Driver Driven. InputSpeed. Gears Gears Gears are toothed wheels designed to transmit rotary motion and power from one part of a mechanism to another. They are fitted to shafts with special devices called keys (or splines) that ensure

More information

OVERLOAD CLUTCHES FOR INDEX DRIVES

OVERLOAD CLUTCHES FOR INDEX DRIVES The Driving Force in Automation OVERLOAD CLUTCHES FOR INDEX DRIVES WARNING WARNING This is a controlled document. It is your responsibility to deliver this information to the end user of the CAMCO indexer.

More information

Maschinentechnik. Controlled dynamics. Centrifugal clutches

Maschinentechnik. Controlled dynamics. Centrifugal clutches Maschinentechnik Controlled dynamics Centrifugal clutches Experts in our field since 1982. Strong clutches do not slip we are driven by centrifugal force! Amsbeck Maschinentechnik GmbH is a leading manufacturer

More information

Permapak Seal Bore Packer

Permapak Seal Bore Packer Quality We Know Downhole. Permapak Seal Bore Packer The D&L Permapak Seal Bore Packer can be used for single or multiple zone completions. It is designed for wells where high pressure/temperatures and

More information

Amerigear Standard Gear Couplings Flanged and Continuous Sleeve Designs

Amerigear Standard Gear Couplings Flanged and Continuous Sleeve Designs A L T R A I N D U S T R I A L M O T I O N Amerigear Standard Gear Couplings Flanged and Continuous Sleeve Designs Fully-Crowned Teeth The Basis For Gear Tooth Design Amerigear... the first, the finest...

More information

Universal Series Style Reference Guide

Universal Series Style Reference Guide STF Universal Series Style Reference Guide SVF Accessories Dimensions P. 161 Dimensions P. 162 ST SB SV Ratio Multipliers In-Line Helical (ILH) Universal Series Universal Series STL Dimensions P. 163 SVL

More information

SHAFT MOUNT REDUCERS. For Additional Models of Shaft Mount Reducers See Sections F & J G-1

SHAFT MOUNT REDUCERS. For Additional Models of Shaft Mount Reducers See Sections F & J G-1 SHAFT MOUNT REDUCERS PowerTorque Features and Description... -2 Nomenclature... -4 Selection Instructions... -5 Selection By Horsepower... -7 Mechanical Ratings... -12 Dimensions... -14 Accessories...

More information

FOR MORE INFORMATION CALL CLARK ROLLER CHAIN SPROCKETS INDEX...E-1 - E-2 MADE-TO-ORDER CAPABILITIES...

FOR MORE INFORMATION CALL CLARK ROLLER CHAIN SPROCKETS INDEX...E-1 - E-2 MADE-TO-ORDER CAPABILITIES... Index SECTION E ROLLER CHAIN PRODUCT PAGE INDEX...E- - E-2 MADE-TO-ORDER CAPABILITIES...E- SECTION I STANDARD...E-4 - E-2 Shear Pin Sprockets, Bolt-On...E-4 - E-6 Type D Sprockets, Detachable s Split and

More information

Section Description Page

Section Description Page Table of contents IOM part number: 204107 Rev. A Section Description Page 1.0 INTRODUCTION 5-6 1.1 Description 5 1.2 How it works 5-6 2.0 INSTALLATION 6-7 2.1 Preparation 6-8 2.2 Mounting 7 2.3 Actuating

More information

COUPLINGS HRC FLEXIBLE COUPLINGS CHAIN SHAFT COUPLINGS SPLINE CLUTCHES TORQUE LIMITERS TORQUE LIMITER COUPLINGS

COUPLINGS HRC FLEXIBLE COUPLINGS CHAIN SHAFT COUPLINGS SPLINE CLUTCHES TORQUE LIMITERS TORQUE LIMITER COUPLINGS COUPLINGS HRC FLEXIBLE COUPLINGS CHAIN SHAFT COUPLINGS SPLINE CLUTCHES TORQUE LIMITERS TORQUE LIMITER COUPLINGS FLEXIBLE COUPLINGS HRC TYPE Hercus HRC Couplings are designed for general-purpose applications

More information

Highest Performance: Dyna Series

Highest Performance: Dyna Series Highest Performance: Dyna Series The Dyna Series is our highest performance right-angle gear reducer utilizing sophisticated hypoid gearing. The benefit of hypoid gearing is that it combines the space

More information

Marathon series corrosion resistant products

Marathon series corrosion resistant products Marathon series corrosion resistant products Contents 2 Introduction 6 End covers 8 Composite units 22 Stainless steel take-up frames 24 Cast stainless steel units 28 ZMaRC-coated insert bearings Stainless

More information

Radial piston motor for heavy duty wheel drives MCR-W

Radial piston motor for heavy duty wheel drives MCR-W Radial piston motor for heavy duty wheel drives MCR-W RE 15200 Edition: 09.2015 Frame size MCR3, MCR5, MCR10 Displacement 160 cc to 1340 cc Differential pressure up to 450 bar Torque output up to 8530

More information

Installation Instructions

Installation Instructions Primary Clutch, Pin Drive Armature, Spline Drive Armature PC-825, PC-1000, PC-1225, PC-1525 Primary Clutch Coupling, Spline Drive Armature PCC-825, PCC-1000, PCC-1225, PCC-1525 P-206 819-0519 Installation

More information

Highest Precision: SPL Series

Highest Precision: SPL Series Highest Precision: SPL Series GAM can. Just ask! If you don t see exactly what you need, let us know. We can modify the SPL Series gearboxes to meet your needs. Page 3 provides a list of commonly requested

More information

Magnetic Particle Brakes and Clutches

Magnetic Particle Brakes and Clutches Magnetic Particle Brakes and Clutches Accurate torque control with instantaneous engagement! Available in a wide range of models and sizes Warner Electric s magnetic particle brakes and clutches are quiet

More information

MODEL CTB TUBULAR CENTRIFUGAL INLINE BELT DRIVEN FAN

MODEL CTB TUBULAR CENTRIFUGAL INLINE BELT DRIVEN FAN MODEL FEATURES Rated up to 20,000 CFM in static pressure applications up to 2-1/2 w.g. Motor drives are located outside of the airstream Ideal for applications where space is limited Belt drives permit

More information

DIST. AUTORIZADO MEX (55) QRO (442) MTY (81)

DIST. AUTORIZADO MEX (55) QRO (442) MTY (81) DIST. AUTORIZADO About WPT Since 992! As an international manufacturer of pneumatic and hydraulic power take-off s, clutches and brakes for a broad range of industrial and petroleum applications, WPT Power

More information

Highest Precision: Dyna Series

Highest Precision: Dyna Series GAM can. Just ask! If you don t see exactly what you need, let us know. We can modify the Dyna Series gearboxes to meet your needs. Page 3 provides a list of commonly requested modifications to give you

More information

FM motor 230V & 460V. FM motor 230V. FM motor 460V. Performance AC Brushless Servo Motor. Servomotors.

FM motor 230V & 460V. FM motor 230V. FM motor 460V. Performance AC Brushless Servo Motor. Servomotors. FM motor 230V & 460V Performance A Brushless Servo FM The FM motor is a high performance brushless A servo motor range matched for use with ontrol Techniques drives. FM is an acronym for Flexible, designed

More information

GatesFacts Technical Information Library Gates Compass Power Transmission CD-ROM version 1.2 The Gates Rubber Company Denver, Colorado USA

GatesFacts Technical Information Library Gates Compass Power Transmission CD-ROM version 1.2 The Gates Rubber Company Denver, Colorado USA SIZING UP V-RIBBED BELTS Gary Porter Machine Design October 22, 1992 V-ribbed belts offer several advantages to power transmission drive design. Classical V-belts have a profile shaped like a modified

More information

11.AWD Transfer System

11.AWD Transfer System W1860BE.book Page 54 Tuesday, January 28, 2003 11:01 PM 11.AWD Transfer System A: MPT MODELS 1. GENERAL This all-wheel-drive (AWD) transfer system uses an electronically controlled multi-plate type transfer

More information

Viking s helical gear reducers are available in three basic sizes, each size offering several gear ratios.

Viking s helical gear reducers are available in three basic sizes, each size offering several gear ratios. PARTS & ACCESSORIES: SIZES A, B & C Section 610 Page 610.1 Issue L Gear Ratio Range: (varies by reducer size) 1.87:1 to 7.95:1 Output Speeds (with 1750 rpm input) 950 to 220 rpm Reducer Horsepower Range:

More information

Differential Rewind Shafts

Differential Rewind Shafts Differential Rewind Shafts More accurate tension control for light tension applications. Dynamically balanced central shaft. Suitable for cardboard and all types of plastic cores. Easier loading of cores

More information

Industrial Disc Brakes

Industrial Disc Brakes A L T R A I N D U S T R I A L M O T I O N Industrial Disc Brakes Twiflex... Leaders In Advanced Braking Technology Page 2-3 Page 4-5 Brake Calipers Introduction/Selection Guide Applications Overview Twiflex,

More information

Tire 16 inch 225/75R inch 255/60R 18

Tire 16 inch 225/75R inch 255/60R 18 417009 133 1. SPECIFICATIONS Description Specification Tire 16 inch 225/75R 16 Tire inflation pressure 18 inch 255/60R 18 Front: 32 psi Rear: 32 psi (44 psi: when the vehicle is fully laden with luggage)

More information

Module 6: Air Foundation Brakes

Module 6: Air Foundation Brakes Air Brakes Terms and Definitions Basic Components That Make Up Air Foundation Brakes Types of Air Foundation Brakes Parts of a Cam Foundation Brake Parts of a Wedge Foundation Brake Parts of a Disc Foundation

More information

Roller Selection Flowchart

Roller Selection Flowchart Selection Selection Flowchart Solus offers a line of conveyor rollers and components which are engineered to provide totally maintenance free service. These rollers are quiet, need no lubrication, are

More information

Hub City Spartan Aluminum Worm Gear Drives

Hub City Spartan Aluminum Worm Gear Drives Spartan Aluminum Worm Gear Features C-2 Selection Instructions C-3 Descriptions C-4 Single Reduction Ratings C-5 Single Reduction Dimensions C-6 to C-7 Double Reduction Worm-Worm Ratings C-8 Double Reduction

More information

CLICK for More Info Online

CLICK for More Info Online CLICK for More Info Online Floater Axle System and Radial-Mount Caliper with Drum-Style Parking Brake System Today s top pro-touring, autocross and road race vehicles often feature some of the largest

More information

Shaft Mounted Speed Reducer. Technical Catalogue

Shaft Mounted Speed Reducer. Technical Catalogue Shaft Mounted Speed Reducer Technical Catalogue Where others fit, We perform Contents The Challenge SMSR stands tall amongst the crowd. Packed full of attention to detail, the Challenge SMSR delivers performance

More information

BRAKE E

BRAKE E 8-1 GENERAL...8-2 SPECIFICATIONS...8-6 COMPONENTS...8-7 FRONT BRAKE...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn1, Cu2 3 TON SERIES)...8-12 DISASSEMBLY INSPECTION REASSEMBLY (Pn2 3 TON SERIES)...8-17 BRAKE

More information

Basic Hydraulic Features. Basic Mechanical Features

Basic Hydraulic Features. Basic Mechanical Features APRIL 2006 1.0 Overview The ETA is designed for flow rates that fall beyond the range of most end suction pumps. Performance extends to 9,500 GPM, 440 feet of head, and 88% efficiency. This range is covered

More information

High Performance: EPR Series

High Performance: EPR Series High Performance: EPR Series GAM can. If you don t see exactly what you need, let us know. We can modify the EPR Series gearboxes to meet your needs. Page 4 provides a list of commonly requested modifications

More information