HSR. LM Guide Global Standard Size Model HSR. Point of Selection. Point of Design. Options. Model No. Precautions on Use

Size: px
Start display at page:

Download "HSR. LM Guide Global Standard Size Model HSR. Point of Selection. Point of Design. Options. Model No. Precautions on Use"

Transcription

1 LM Guide Global Standard Size Model Retainer plate Endplate End seal Grease nipple Ball Retainer plate Inner seal (Optional) Side seal LM rail Cross section Point of Selection A Point of Design Options Model No. Precautions on Use Accessories for Lubrication A Mounting Procedure and Maintenance B Equivalent moment factor A Rated Loads in All Directions A Equivalent factor in each direction A Radial Clearance A Accuracy Standards A Shoulder Height of the Mounting Base and the Corner Radius Permissible Error of the Mounting Surface Dimensions of Each Model with an Option Attached

2 Structure and Features Balls roll in four rows of raceways precision-ground on an LM rail and an, and endplates incorporated in the allow the balls to circulate. Since retainer plates hold the balls, they do not fall off even if the LM rail is pulled out (except models 8, 10 and 12). Each row of balls is placed at a contact angle of 45 so that the rated loads applied to the are uniform in the four directions (radial, reverse radial and lateral directions), enabling the LM Guide to be used in all orientations. In addition, the can receive a well-balanced preload, increasing the rigidity in the four directions while maintaining a constant, low friction coeffi cient. With the low sectional height and the high rigidity design of the, this model achieves highly accurate and stable straight motion. LM Guide 4-way Equal Load Each row of balls is placed at a contact angle of 45 so that the rated loads applied to the are uniform in the four directions (radial, reverse radial and lateral directions), enabling the LM Guide to be used in all orientations and in extensive applications. High Rigidity Type Since balls are arranged in four rows in a well-balanced manner, a large preload can be applied and the rigidity in four directions can easily be increased. Self-adjustment Capability The self-adjustment capability through front-to-front configuration of THK s unique circular-arc grooves (DF set) enables a mounting error to be absorbed even under a preload, thus to achieve highly accurate, smooth straight motion. High Durability Even under a preload or excessive biased load, differential slip of balls does not occur. As a result, smooth motion, high wear resistance, and long-term maintenance of accuracy are achieved. Stainless Steel Type also Available A special type which, LM rail and balls are made of stainless steel is also available.

3 Types Model -A The flange of its has tapped holes. Specification Table Model -B The fl ange of the has through holes. Used in places where the table cannot have through holes for mounting bolts. Specification Table Model -R Having a smaller width (W) and tapped holes, this model is optimal for compact design. Specification Table

4 Model -YR When using two units of LM Guide facing each other, the previous model required much time in machining the table and had diffi culty achieving the desired accuracy and adjusting the clearance. Since model -YR has tapped holes on the side of the, a simpler structure is gained and reduced man-hour and increase in accuracy can be achieved. Specification Table LM Guide Fig.1 Conventional Structure Model -LA The has the same cross-sectional shape as model -A, but has a longer overall LM block length (L) and a greater rated load. Fig.2 Mounting Structure for Model -YR Specification Table Model -LB The has the same cross-sectional shape as model -B, but has a longer overall LM block length (L) and a greater rated load. Specification Table

5 Model -LR The has the same cross-sectional shape as model -R, but has a longer overall LM block length (L) and a greater rated load. Specification Table Model -CA Has six tapped holes on the. Specification Table Model -CB Specification Table The has six through holes. Used in places where the table cannot have through holes for mounting bolts.

6 Model -HA The has the same cross-sectional shape as model -CA, but has a longer overall LM block length (L) and a greater rated load. Specification Table LM Guide Model -HB The has the same cross sectional shape as model -CB, but has a longer overall LM block length (L) and a greater rated load. Specification Table Models 100/120/150 HA/HB/HR Large types of model that can be used in large-scale machine tools and building structures. Specification Table

7 Models -A and -AM, Models -LA and -LAM Models 15 to 35A/LA/AM/LAM Outer dimensions dimensions Models 45 to 85A/LA Model No. 15A 15AM 20A 20AM 20LA 20LAM 25A 25AM 25LA 25LAM 30A 30AM 30LA 30LAM 35A 35AM 35LA 35LAM 45A 45LA 55A 55LA 65A 65LA 85A 85LA Height Width Length Grease nipple M W L B C S L 1 t T T 1 K N E H M PB1021B M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-PT1/ M B-PT1/ M B-PT1/ M B-PT1/8 16 Model number coding 25 A 2 QZ UU C0 M +1200L P T M - Model number Type of No. of s used on the same rail Contamination With QZ protection Lubricator accessory symbol (*1) Stainless steel Radial clearance symbol (*2) Normal (No symbol) Light preload (C1) Medium preload (C0) LM rail length Stainless steel Symbol for LM rail (in mm) No. of rails used Symbol for LM rail on the same jointed use plane (*4) Accuracy symbol (*3) Normal grade (No Symbol)/High accuracy grade (H) Precision grade (P)/Super precision grade (SP) Ultra precision grade (UP) (*1) See contamination protection accessory on. (*2) See A. (*3) See A. (*4) See A. Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.) Those models equipped with QZ Lubricator cannot have a grease nipple. When desiring a grease nipple for a model attached with QZ, contact THK.

8 E L L1 C φ d2 N M1 h φ d1 F LM Guide Unit: mm LM rail dimensions Basic load rating Static permissible moment kn-m Mass M A M B M C LM LM Width Height Pitch Length C C 0 block rail W W 2 M 1 F d 1 d 2 h Max kn kn 1 block (1240) (1480) (1480) (2020) (2020) Note) Symbol M indicates that stainless steel is used in the, LM rail and balls. Those models marked with this symbol are therefore highly resistant to corrosion and environment. The maximum length under Length indicates the standard maximum length of an LM rail. (See.) Static permissible moment : 1 block: static permissible moment value with 1 Double blocks: static permissible moment value with 2 blocks closely contacting with each other kg kg/m Options

9 Models -B, -BM, -LB and -LBM 4-φ H W B M t T T1 K H3 W2 W1 Outer dimensions dimensions Model No. Height Width Length Grease nipple 15B 15BM 20B 20BM 20LB 20LBM 25B 25BM 25LB 25LBM 30B 30BM 30LB 30LBM 35B 35BM 35LB 35LBM 45B 45LB 55B 55LB 65B 65LB 85B 85LB M W L B C H L 1 t T T 1 K N E H PB1021B B-M6F B-M6F B-M6F B-M6F B-M6F B-M6F B-M6F B-M6F B-PT1/ B-PT1/ B-PT1/ B-PT1/8 16 Model number coding 25 B 2 QZ UU C0 M +1200L P T M - Model number Type of No. of s used on the same rail With QZ Contamination protection Lubricator accessory symbol (*1) Stainless steel Radial clearance symbol (*2) Normal (No symbol) Light preload (C1) Medium preload (C0) LM rail length (in mm) Stainless steel LM rail Symbol for LM rail jointed use Symbol for No. of rails used on the same plane (*4) Accuracy symbol (*3) Normal grade (No Symbol)/High accuracy grade (H) Precision grade (P)/Super precision grade (SP) Ultra precision grade (UP) (*1) See contamination protection accessory on. (*2) See A. (*3) See A. (*4) See A. Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.) Those models equipped with QZ Lubricator cannot have a grease nipple. When desiring a grease nipple for a model attached with QZ, contact THK.

10 E L L1 C φ d2 N M1 h φ d1 F Unit: mm LM rail dimensions Basic load rating Static permissible moment kn-m Mass M A M B M C LM LM Width Height Pitch Length C C 0 block rail W W 2 M 1 F d 1 d 2 h Max kn kn 1 block (1240) (1480) (1480) (2020) (2020) Note) Symbol M indicates that stainless steel is used in the, LM rail and balls. Those models marked with this symbol are therefore highly resistant to corrosion and environment. The maximum length under Length indicates the standard maximum length of an LM rail. (See.) Static permissible moment : 1 block: static permissible moment value with 1 Double blocks: static permissible moment value with 2 blocks closely contacting with each other kg kg/m LM Guide Options

11 Model -RM W L 4-S l B L1 φ d N φ d2 C M K H3 M1 h φ d1 W2 W1 F Models 8RM and 10RM Outer dimensions dimensions Model No. Height Width Length Greasing hole Grease nipple M W L B C S l L 1 T K N E d H 3 8RM M RM M RM M PB Model number coding 12 R 2 UU C1 M +670L H T M - Model number Type of No. of s used on the same rail Contamination protection accessory symbol (*1) Stainless steel Radial clearance symbol (*2) Normal (No symbol) Light preload (C1) LM rail length (in mm) Stainless steel LM rail Symbol for LM rail jointed use Symbol for No. of rails used on the same plane (*4) Accuracy symbol (*3) Normal grade (No Symbol)/High accuracy grade (H) Precision grade (P)/Super precision grade (SP) (*1) See contamination protection accessory on. (*2) See A. (*3) See A. (*4) See A. Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.)

12 4-S l W B E L L1 M T K H3 M1 h φ d2 N C LM Guide φ d1 W2 W1 F Model 12RM LM rail dimensions Basic load rating Static permissible moment kn-m Mass Width Height Pitch Length C C 0 W W 2 M 1 F d 1 d 2 h Max kn kn M A M B M C 1 block Double blocks 1 block LM block Unit: mm (975) (995) (1240) Note) Since stainless steel is used in the, LM rail and balls, these models are highly resistant to corrosion and environment. The maximum length under Length indicates the standard maximum length of an LM rail. (See.) Static permissible moment : 1 block: static permissible moment value with 1 Double blocks: static permissible moment value with 2 blocks closely contacting with each other kg LM rail kg/m Options

13 Models -R, -RM, -LR and -LRM 4-S l W B T M K H3 W2 W1 Outer dimensions dimensions Model No. Height Width Length Grease nipple 15R 15RM 20R 20RM 20LR 20LRM 25R 25RM 25LR 25LRM 30R 30RM 30LR 30LRM 35R 35RM 35LR 35LRM 45R 45LR 55R 55LR 65R 65LR 85R 85LR M W L B C S l L 1 T K N E H M PB1021B M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-PT1/ M B-PT1/ M B-PT1/ M B-PT1/8 16 Model number coding 35 R 2 QZ SS C0 M +1400L P T M - Model number Type of With QZ Lubricator No. of s used on the same rail Contamination protection accessory symbol (*1) Stainless steel Radial clearance symbol (*2) Normal (No symbol) Light preload (C1) Medium preload (C0) LM rail length (in mm) Stainless steel LM rail Symbol for LM rail jointed use Symbol for No. of rails used on the same plane (*4) Accuracy symbol (*3) Normal grade (No Symbol)/High accuracy grade (H) Precision grade (P)/Super precision grade (SP) Ultra precision grade (UP) (*1) See contamination protection accessory on. (*2) See A. (*3) See A. (*4) See A. Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.) Those models equipped with QZ Lubricator cannot have a grease nipple. When desiring a grease nipple for a model attached with QZ, contact THK.

14 E L L1 C φ d2 N M1 h φ d1 F Unit: mm LM rail dimensions Basic load rating Static permissible moment kn-m Mass M A M B M C LM LM Width Height Pitch Length C C 0 block rail W W 2 M 1 F d 1 d 2 h Max kn kn 1 block (1240) (1480) (1480) (2020) (2020) Note) Symbol M indicates that stainless steel is used in the, LM rail and balls. Those models marked with this symbol are therefore highly resistant to corrosion and environment. The maximum length under Length indicates the standard maximum length of an LM rail. (See.) Static permissible moment : 1 block: static permissible moment value with 1 Double blocks: static permissible moment value with 2 blocks closely contacting with each other kg kg/m LM Guide Options

15 Models -YR and -YRM 4-S l W B1 M B K H3 W1 W2 Outer dimensions dimensions Model No. Height Width Length Grease nipple M W L B 1 B C S l L 1 K N E H 3 15YR 15YRM 20YR 20YRM 25YR 25YRM 30YR 30YRM 35YR 35YRM M PB1021B M B-M6F M B-M6F M B-M6F M B-M6F YR M B-PT1/ YR M B-PT1/ YR M B-PT1/8 14 Model number coding 25 YR 2 UU C0 M +1200L P T M - Model number Type of No. of s used on the same rail Contamination protection accessory symbol (*1) Stainless steel Radial clearance symbol (*2) Normal (No symbol) Light preload (C1) Medium preload (C0) LM rail length (in mm) Stainless steel LM rail Symbol for LM rail jointed use Symbol for No. of rails used on the same plane (*4) Accuracy symbol (*3) Normal grade (No Symbol)/High accuracy grade (H) Precision grade (P)/Super precision grade (SP) Ultra precision grade (UP) (*1) See contamination protection accessory on. (*2) See A. (*3) See A. (*4) See A. Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.)

16 E L L1 C φ d2 N M1 h LM Guide φ d1 F LM rail dimensions Basic load rating Static permissible moment kn-m Mass Unit: mm Width Height Pitch Length C C 0 M A M B M C LM block LM rail W W 2 M 1 F d 1 d 2 h Max kn kn (1240) (1480) (2020) 1 block kg kg/m Note) Symbol M indicates that stainless steel is used in the, LM rail and balls. Those models marked with this symbol are therefore highly resistant to corrosion and environment. The maximum length under Length indicates the standard maximum length of an LM rail. (See.) Static permissible moment : 1 block: static permissible moment value with 1 Double blocks: static permissible moment value with 2 blocks closely contacting with each other Options

17 Models -CA, -CAM, -HA and -HAM 6-S W B 6-S W B T T1 M K M T1 T t K H3 H3 W2 W1 W2 W1 Models 20 to 35CA/HA/CAM/HAM Outer dimensions dimensions Models 45 to 85CA/HA Model No. Height Width Length Grease nipple 20CA 20CAM 20HA 20HAM 25CA 25CAM 25HA 25HAM 30CA 30CAM 30HA 30HAM 35CA 35CAM 35HA 35HAM 45CA 45HA 55CA 55HA 65CA 65HA 85CA 85HA M W L B C S L 1 t T T 1 K N E H M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-M6F M B-PT1/ M B-PT1/ M B-PT1/ M B-PT1/8 16 Model number coding 25 HA 2 QZ KKHH C0 M +1300L P T M - Model number Type of No. of s used on the same rail With QZ Lubricator Contamination protection accessory symbol (*1) Radial clearance symbol (*2) Normal (No symbol) Light preload (C1) Medium preload (C0) Stainless steel LM rail length (in mm) Accuracy symbol (*3) Normal grade (No Symbol) High accuracy grade (H) Precision grade (P) Super precision grade (SP) Ultra precision grade (UP) Stainless steel LM rail Symbol for LM rail jointed use Symbol for No. of rails used on the same plane (*4) (*1) See contamination protection accessory on. (*2) See A. (*3) See A. (*4) See A. Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.) Those models equipped with QZ Lubricator cannot have a grease nipple. When desiring a grease nipple for a model attached with QZ, contact THK.

18 E L L1 C φ d2 N M1 h φ d1 F LM Guide Unit: mm LM rail dimensions Basic load rating Static permissible moment kn-m Mass M A M B M C LM LM Width Height Pitch Length C C 0 block rail W W 2 M 1 F d 1 d 2 h Max kn kn 1 block (1480) (1480) (2020) (2020) Note) Symbol M indicates that stainless steel is used in the, LM rail and balls. Those models marked with this symbol are therefore highly resistant to corrosion and environment. The maximum length under Length indicates the standard maximum length of an LM rail. (See.) Static permissible moment : 1 block: static permissible moment value with 1 Double blocks: static permissible moment value with 2 blocks closely contacting with each other kg kg/m Options

19 Models -CB, -CBM, -HB and -HBM 6-φ H W B M t T T1 K H3 W2 W1 Outer dimensions dimensions Model No. Height Width Length Grease nipple 20CB 20CBM 20HB 20HBM 25CB 25CBM 25HB 25HBM 30CB 30CBM 30HB 30HBM 35CB 35CBM 35HB 35HBM 45CB 45HB 55CB 55HB 65CB 65HB 85CB 85HB M W L B C H L 1 t T T 1 K N E H B-M6F B-M6F B-M6F B-M6F B-M6F B-M6F B-M6F B-M6F B-PT1/ B-PT1/ B-PT1/ B-PT1/8 16 Model number coding 35 CB 2 QZ ZZHH C0 M +1400L P T M - Model number Type of No. of s used on the same rail With QZ Lubricator Contamination protection accessory symbol (*1) Radial clearance symbol (*2) Normal (No symbol) Light preload (C1) Medium preload (C0) Stainless steel LM rail length (in mm) Accuracy symbol (*3) Normal grade (No Symbol) High accuracy grade (H) Precision grade (P) Super precision grade (SP) Ultra precision grade (UP) Stainless steel LM rail Symbol for LM rail jointed use Symbol for No. of rails used on the same plane (*4) (*1) See contamination protection accessory on. (*2) See A. (*3) See A. (*4) See A. Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.) Those models equipped with QZ Lubricator cannot have a grease nipple. When desiring a grease nipple for a model attached with QZ, contact THK.

20 E L L1 C φ d2 N M1 h φ d1 F Unit: mm LM rail dimensions Basic load rating Static permissible moment kn-m Mass M A M B M C LM LM Width Height Pitch Length C C 0 block rail W W 2 M 1 F d 1 d 2 h Max kn kn 1 block (1480) (1480) (2020) (2020) Note) Symbol M indicates that stainless steel is used in the, LM rail and balls. Those models marked with this symbol are therefore highly resistant to corrosion and environment. The maximum length under Length indicates the standard maximum length of an LM rail. (See.) Static permissible moment : 1 block: static permissible moment value with 1 Double blocks: static permissible moment value with 2 blocks closely contacting with each other kg kg/m LM Guide Options

21 Models -HA, -HB and -HR 9-S W B 9-φ H W B M T1 T K M T1 T K H3 H3 W2 W1 W2 W1 Models 100 to 150HA Models 100 to 150HB Outer dimensions dimensions Model No. Height Width Length Grease nipple 100HA 100HB 100HR 120HA 120HB 120HR 150HA 150HB 150HR Model number coding M W L B C H S l L 1 T T 1 K N E H Note) indicates a through hole M18 M18 27 M20 M20 30 M24 M HR 2 UU C L H T - Model number Type of No. of s used on the same rail Contamination protection accessory symbol (*1) LM rail length (in mm) Radial clearance symbol (*2) Normal (No symbol) Light preload (C1) Medium preload (C0) Symbol for LM rail jointed use B-PT1/ B-PT1/ B-PT1/4 22 Symbol for No. of rails used on the same plane (*4) Accuracy symbol (*3) Normal grade (No Symbol)/High accuracy grade (H) Precision grade (P)/Super precision grade (SP) Ultra precision grade (UP) (*1) See contamination protection accessory on. (*2) See A. (*3) See A. (*4) See A. Note) This model number indicates that a single-rail unit constitutes one set. (i.e., required number of sets when 2 rails are used in parallel is 2 at a minimum.)

22 E L 6-S l W B L1 C M T W2 W1 K H3 M1 h φ d2 N φ d1 F LM Guide Models 100 to 150HR LM rail dimensions Basic load rating Static permissible moment kn-m Mass Unit: mm Width Height Pitch Length C C 0 M A M B M C LM block LM rail W W 2 M 1 F d 1 d 2 h Max kn kn block Note) The maximum length under Length indicates the standard maximum length of an LM rail. (See.) Static permissible moment : 1 block: static permissible moment value with 1 Double blocks: static permissible moment value with 2 blocks closely contacting with each other kg kg/m Options

23 Standard Length and Maximum Length of the LM Rail Table1 shows the standard lengths and the maximum lengths of model variations. If the maximum length of the desired LM rail exceeds them, jointed rails will be used. Contact THK for details. For the G dimension when a special length is required, we recommend selecting the corresponding G value from the table. The longer the G dimension is, the less stable the G area may become after installation, thus causing an adverse impact to accuracy. G F F G L0 Table1 Standard Length and Maximum Length of the LM Rail for Model Unit: mm Model No LM rail standard length (L O ) Standard pitch F G Max length (975) (995) (1240) (1240) (1480) (2020) Note1) The maximum length varies with accuracy grades. Contact THK for details. Note2) If jointed rails are not allowed and a greater length than the maximum values above is required, contact THK. Note3) The figures in the parentheses indicate the maximum lengths of stainless steel made models.

24 Tapped-hole LM Rail Type of Model model rails also include a type where the LM rail is tapped from the bottom. This type is useful when mounting from the bottom of the base and when increased contamination protection is desired. LM Guide Clearance l 1 S1 F (1) Determine the bolt length so that a clearance of 2 to 5 mm is secured between the bolt end and the bottom of the tap (effective tap depth). (See figure above.) (2) A tapped-hole LM rail type is available also for model -YR. (3) For standard pitches of the taps, see Table1 on. Table2 Dimensions of the LM Rail Tap Unit: mm Model No. S 1 Effective tap depth l 1 15 M M M M M M M M20 30 Model number coding 30A2UU +1000LH K Symbol for tapped-hole LM rail type

25 Prevention of from falling off of LM rail In miniature model, the balls fall out if the comes off the LM rail. For this reason, LM Guide assemblies are delivered with a part which prevents the from coming off the rail. If you remove this part when using the product, please take precautions to avoid overrunning the blocks off of the rail. Greasing Hole Semi-standard Greasing Hole for Model For model, a semi-standard greasing hole is available. Specify the appropriate model number according to the application. Greasing hole Greasing hole Type with a Greasing Hole Drilled on the Side Surface Type with a Greasing Hole Drilled on the Top Face

26 LM Guide

SHS. Caged Ball LM Guide Global Standard Size Model SHS. Point of Selection. Point of Design. Options. Model No. Precautions on Use

SHS. Caged Ball LM Guide Global Standard Size Model SHS. Point of Selection. Point of Design. Options. Model No. Precautions on Use Caged Ball LM Guide Global Standard Size Model LM block LM rail Endplate End seal 45 Ball Ball cage Cross section 45 * For the Ball Cage, see. Point of Selection Point of Design Options Model No. Precautions

More information

HSR-M1. LM Guide High Temperature Type Model HSR-M1. Point of Selection. Point of Design. Options. Model No. Precautions on Use

HSR-M1. LM Guide High Temperature Type Model HSR-M1. Point of Selection. Point of Design. Options. Model No. Precautions on Use LM Guide High Temperature Type Model Endplate SUS304 End seal (High temperature rubber material) LM THK-EX50 Ball SUS440C Side seal (High temperature rubber material) LM rail THK-EX50 Cross section 45

More information

SSR. Caged Ball LM Guide Radial Type Model SSR. Point of Selection. Point of Design. Options. Model No. Precautions on Use

SSR. Caged Ball LM Guide Radial Type Model SSR. Point of Selection. Point of Design. Options. Model No. Precautions on Use Caged Ball LM Guide Radial Type Model Endplate LM block End seal LM 90 30 Ball Ball cage Cross section * For the Ball Cage, see A. Point of Selection A Point of Design Options Precautions on Use Accessories

More information

LM Guide Radial Type Model SR

LM Guide Radial Type Model SR LM Guide Radial Type Model Endplate LM block Grease nipple End seal LM rail 90 Ball Retainer plate Side seal (Optional) Cross section 30 Point of Selection A Point of Design Options Model No. Precautions

More information

511E. LM Guide General Catalog

511E. LM Guide General Catalog General Catalog A Classification Table of the s Ball Guide Caged Ball Type Full-ball Type Standard Type Standard Type Model SHS Global Standard Size Model SSR Radial Model HSR 4-way Equal Load Model SR

More information

SRG. Caged Roller LM Guide Ultra-high Rigidity Type Model SRG. Point of Selection. Point of Design. Options. Model No. Precautions on Use

SRG. Caged Roller LM Guide Ultra-high Rigidity Type Model SRG. Point of Selection. Point of Design. Options. Model No. Precautions on Use Caged Roller LM Guide Ultra-high Rigidity Type Model LM block LM rail End seal Endplate 45 45 Caged roller Roller 45 Cross section 45 * or the caged roller, see. Point of Selection A Point of Design Options

More information

NSR-TBC. LM Guide Self-aligning Type Model NSR-TBC. Point of Selection. Point of Design. Options. Model No. Precautions on Use

NSR-TBC. LM Guide Self-aligning Type Model NSR-TBC. Point of Selection. Point of Design. Options. Model No. Precautions on Use LM Guide Self-aligning Type Model LM casing Spline nut End seal LM rail Grease nipple Side plate Clearance adjustment bolt 90 Side seal (Optional) Ball Retainer Cross section 30 Point of Selection A Point

More information

SVR/SVS. Caged Ball LM Guide Ultra-heavy Load Type for Machine Tools Model SVR/SVS. Point of Selection. Point of Design. Options. Model No.

SVR/SVS. Caged Ball LM Guide Ultra-heavy Load Type for Machine Tools Model SVR/SVS. Point of Selection. Point of Design. Options. Model No. Caged Ball Guide Ultra-heavy Load Type for Machine Tools Model Protector 90 rail Ball cage Radial type model SVR Cross section 40 50 Ball * For the Ball Cage, see A. 4-Way Type Model SVS Cross section

More information

RSR. LM Guide Miniature Types Model RSR. Point of Selection. Point of Design. Options. Model No. Precautions on Use

RSR. LM Guide Miniature Types Model RSR. Point of Selection. Point of Design. Options. Model No. Precautions on Use LM Guide Miniature Types Model Endplate LM block End seal LM rail Ball Grease nipple Cross section Point of Selection A Point of Design Options Model No. Precautions on Use Accessories for Lubrication

More information

RSR-M1. LM Guide High Temperature Type Model RSR-M1. Point of Selection. Point of Design. Options. Model No. Precautions on Use

RSR-M1. LM Guide High Temperature Type Model RSR-M1. Point of Selection. Point of Design. Options. Model No. Precautions on Use LM Guide High Temperature Type Model Endplate SUS34 LM block THK EX5 End seal (High temperature rubber) LM rail THK EX5 Ball SUS44C Grease nipple SUS34 Point of Selection A Point of Design Options Model

More information

SRS. Caged Ball LM Guide Miniature Type Model SRS. Point of Selection. Point of Design. Options. Model No. Precautions on Use

SRS. Caged Ball LM Guide Miniature Type Model SRS. Point of Selection. Point of Design. Options. Model No. Precautions on Use Caged Ball M Guide Miniature Type Model M rail Endplate End seal M block Compact type Model -M Ball Side seal Ball cage Wide type Model -WM * or the ball cage, see A. Point of Selection A Point of Design

More information

Caged Roller LM Guide

Caged Roller LM Guide Caged Roller LM Guide SRG/SRN Ultra-high Rigidity Long-term Maintenance-free Operation Smooth Motion Wide Array of Options For details, visit THK at www.thk.com Product information is updated regularly

More information

HSR-M1VV. LM Guide Medium-to-low Vacuum Type Model HSR-M1VV. Point of Selection. Point of Design. Options. Model No. Precautions on Use

HSR-M1VV. LM Guide Medium-to-low Vacuum Type Model HSR-M1VV. Point of Selection. Point of Design. Options. Model No. Precautions on Use LM Guide Medium-to-low Vacuum Type Model LM block: THK-EX50 (martensitic stainless steel) End plate: SUS304 Labyrinth end seal dedicated for Medium-to-Low Vacuum: SUS304 Upper plate: SUS316L LM rail: THK-EX50

More information

12.5 Ball Chain Type, SME Series

12.5 Ball Chain Type, SME Series 12.5 Ball Chain Type, SME Series A. Construction Carriage End Cap End Seal Grease Nipple Inner Seal Ball Bottom Seal Ball Chain 45 Rail 45 B. Characteristics The ball chain type linear guideway, SME series,

More information

Introduction of Each Series

Introduction of Each Series 12 Introduction of Each Series 12.1 eavy Load Type, MSA Series A. Construction LINEAR GUIDEWAY Upper Retainer Carriage End Cap End Seal Grease Nipple Ball Lower Retainer Rail 45 eavy Load Type, MSA Series

More information

12.3 Full Roller Type, MSR Series

12.3 Full Roller Type, MSR Series 12.3 Full Roller Type, MSR Series A. Construction Carriage End Seal Grease Nipple End Cap Inner Seal Roller Bottom Seal 45 Rail 45 B. Characteristics The full roller type linear guideway, MSR series, equip

More information

506E. LM Guide Actuator General Catalog

506E. LM Guide Actuator General Catalog LM Guide Actuator General Catalog A LM Guide Actuator General Catalog A Product Descriptions 506E Caged Ball LM Guide Actuator Model SKR.. A2-4 Structure and Features... A2-4 Caged Ball Technology... A2-6

More information

Inner block. Grease nipple. Fig.1 Structure of LM Guide Actuator Model KR

Inner block. Grease nipple. Fig.1 Structure of LM Guide Actuator Model KR LM Guide ctuator Model LM Guide + all Screw = Integral-structure ctuator Stopper Housing all screw Inner block Grease nipple Outer rail earing (supported side) Housing Stopper Double-row ball circuit earing

More information

Features of the LM Guide

Features of the LM Guide Features of the Functions Required for Linear Guide Surface Large permissible load Highly rigid in all directions High positioning repeatability Running accuracy can be obtained easily High accuracy can

More information

Linear Guideways HG Series

Linear Guideways HG Series 18 G99TE1-67 Linear Guideways 2-1 - Heavy Load Ball Type Linear Guideway HG series linear guideways are designed with load capacity and rigidity higher than other similar products with circular-arc groove

More information

Ball. Ball cage. Fig.1 Structure of Caged Ball LM Guide Actuator Model SKR

Ball. Ball cage. Fig.1 Structure of Caged Ball LM Guide Actuator Model SKR Caged all LM Guide Actuator Model Inner block all screw shaft Grease nipple Outer rail all cage all Structure and Features Fig.1 Structure of Caged all LM Guide Actuator Model Caged all LM Guide Actuator

More information

Features of the LM Guide

Features of the LM Guide Features of the Functions Required for Linear Guide Surface Large permissible load Highly rigid in all directions High positioning repeatability Running accuracy can be obtained easily High accuracy can

More information

Wide Caged-roller LM Guide

Wide Caged-roller LM Guide NEW Wide Caged-roller LM Guide Optimal for large machines that require high rigidity and mounting accuracy Ultra-high rigidity, heavy load A wide, large roller guide model is added to the lineup CATALOG

More information

Ballscrews / Linear Guideway General Catalog

Ballscrews / Linear Guideway General Catalog Ballscrews / inear Guideway General Catalog inear Guideway 2 Introduction of ach Series 2. eavy oad Type, MSA Series A. Construction Upper Retainer Carriage nd Seal nd Cap Rail Grease Nipple Ball 45 ower

More information

SRW NEW. Wide Type Roller Guide with Caged Technology

SRW NEW. Wide Type Roller Guide with Caged Technology NEW Roller Wide Type Roller Guide with Caged Technology Ultra-High Rigidity, Heavy Load Low Friction Long Service Life, Long-Term Maintenance-Free Operation SRW This catalog uses recycled paper. CATALOG

More information

Caged Ball LM Guide. Ball Cage Effect Wide, Low Center of Gravity Type SHW. CATALOG No.248-5E

Caged Ball LM Guide. Ball Cage Effect Wide, Low Center of Gravity Type SHW. CATALOG No.248-5E Caged Ball LM Guide Ball Cage Effect Wide, Low Center of Gravity Type SHW CATALOG No.248-E Ball Cage Effect The early forms of ball bearings were full-ball types without ball cages. Friction between balls

More information

Precision, Caged Ball Screw

Precision, Caged Ball Screw Models SBN, SBK, SDA, HBN and SBKH Pipe presser Screw shaft Return pipe Ball screw nut Ball Ball cage Fig.1 Structure of High-Speed Ball Screw with Ball Cage Model SBN Point of Selection Options Model

More information

JPF, BTK-V, MTF, WHF, BLK/WTF, CNF

JPF, BTK-V, MTF, WHF, BLK/WTF, CNF Rolled Models JPF, BTK-V, MTF, WF, BLK/WTF, CNF and BNT Point of Selection Options Model No. Precautions on Use Accessories for Lubrication Mounting Procedure and Maintenance A A B Lead Angle Accuracy

More information

SHS. Caged Ball LM Guide. Ball Cage Effect Global Standard Size. BERG AB Тел. (495) , ф.

SHS. Caged Ball LM Guide. Ball Cage Effect Global Standard Size.   BERG AB Тел. (495) , ф. www.thk.ru BERG AB thk@thk.ru Тел. (49)-727-22-72, ф. (49)-22-71 Caged Ball LM Guide Ball Cage Effect Global Standard Size SHS CATALOG No.2-1E www.thk.ru BERG AB thk@thk.ru Тел. (49)-727-22-72, ф. (49)-22-71

More information

2-1 HG Series - Heavy Load Ball Type Linear Guideway

2-1 HG Series - Heavy Load Ball Type Linear Guideway 2 G99TE15-114 Linear Guideways 2-1 - Heavy Load Ball Type Linear Guideway HG series linear guideways are designed with load capacity and rigidity higher than other similar products with circular-arc groove

More information

Linear Guideway. Forniture per l Industria Gelmini S.r.l.

Linear Guideway. Forniture per l Industria Gelmini S.r.l. Linear Guideway Forniture per l Industria Gelmini S.r.l. Sede Via Cerati, 3/A 43126 Parma Tel. 0521.993844 Fax 0521.291688 Filiale Via Tiziano, 11 46040 Z.I. Guidizzolo (MN) Tel. 0376.847123 Fax 0376.840319

More information

Guide plate. Fig. 1 Construction of Slide Pack Type FBW-RUU

Guide plate. Fig. 1 Construction of Slide Pack Type FBW-RUU A Slide Pack Slide Pack Type FBW Japanese patent No. 1696446 Overseas patent resistered in the U.S. Mounting plate Ball Slide rail Seal Guide plate Stopper Fig. 1 Construction of Slide Pack Type FBW-RUU

More information

LM Guide HCR/HMG. R Guide / Straight-Curved Guide Achieving a Simplified Mechanism. For details, visit THK at CATALOG No.

LM Guide HCR/HMG. R Guide / Straight-Curved Guide Achieving a Simplified Mechanism. For details, visit THK at  CATALOG No. LM Guide HCR/HMG R Guide / Straight-Curved Guide Achieving a Simplified Mechanism For details, visit THK at www.thk.com Product information is updated regularly on the THK website., CATALOG No.306-8E HCR

More information

2. HG Series Linear Guideway Four-row Super Heavy Load

2. HG Series Linear Guideway Four-row Super Heavy Load 16 2. HG Series Linear Guideway Four-row Super Heavy Load 2-1 Features of the HG Series Linear Guideway 2-2 Construction of HG Series Block Cap End cap End seal (Double seals and scraper) Rail Grease nipple

More information

HSR(Ct Grade) Cost effective Type (Ct Grade) of LM Guide Debuts STOCK DISPONIBLE ENTREGA INMEDIATA

HSR(Ct Grade) Cost effective Type (Ct Grade) of LM Guide Debuts STOCK DISPONIBLE ENTREGA INMEDIATA Cost effective Type (Ct Grade) of L Guide Debuts A cost effective series of the well-established model HSR has been newly added. Optimal for the general linear guide market such as for conveyance systems!

More information

SRG. CATALOG No.270-4E

SRG. CATALOG No.270-4E Roller SRG CATALOG No.27-4E LM Guide with Caged Roller TechnologySRG LM rail LM block End seal End plate Pipe Retaining plate Caged Roller Roller cage Roller Caged roller retaining plates 45 45 Enlarged

More information

Features of the Slide Pack

Features of the Slide Pack BER AB тел. (495) 727-22-72 thk-mail@ya.ru Features and Types Features of the Mounting plate Ball Ball case Slide rail Seal uide plate Stopper Slider Structure and Features Fig.1 Structure of Model FBW-RUU

More information

Caged Ball LM Guide Actuator SKR

Caged Ball LM Guide Actuator SKR Caged Ball LM Guide Actuator SKR For details, visit THK at www.thk.com Product information is updated regularly on the THK website. CATALOG No.309-11E Integrated LM Guide and Ball Screw High-rigidity /

More information

Caged Ball LM Guide SPR / SPS

Caged Ball LM Guide SPR / SPS Caged Ball LM Guide SPR / SPS Adopts 8 Rows of Raceways Achieves Super-Low Waving and Ultra-High Rigidity For details, visit THK at www.thk.com Product information is updated regularly on the THK website.

More information

BERG AB Тел. (495) , ф. (495) S B L B L Max. [N]

BERG AB Тел. (495) , ф. (495) S B L B L Max. [N] www.thk.ru BERG AB thk@thk.ru Тел. (9)-77--7, ф. (9)-3-3071 Micro-LM Systems Micro-LM Guide RSR-M RSR-M 1 and P R O T O T Y P E Smallest LM Guide worldwide The micro series of RSR type are miniaturized

More information

SNR/SNS. Advantages of Caged Ball Technology. Revised basic dynamic load ratings

SNR/SNS. Advantages of Caged Ball Technology. Revised basic dynamic load ratings Advantages of aged Ball Technology High speed performance Low noise design, Long service life Long-term maintenance-free operation Reduction in rolling resistance variation SNR/SNS Revised basic dynamic

More information

504E. LM Guide Actuator General Catalog

504E. LM Guide Actuator General Catalog LM Guide Actuator General Catalog A LM Guide Actuator General Catalog A Product Descriptions 504E Caged Ball LM Guide Actuator Model SKR.. A2-4 Structure and Features... A2-4 Caged Ball Technology... A2-6

More information

Miniature LM Guide RSR and RSR-W

Miniature LM Guide RSR and RSR-W iniature Guide RSR and RSR End plate block rail End seal Ball Greace nipple ig. 1 onstruction of odel RSRV onstruction and eatures Balls roll in two rows of precisionground raceways on an rail and an block.

More information

LM Guide Structural Member Rail Four-way Equal Load Type

LM Guide Structural Member Rail Four-way Equal Load Type LM Guide Structural Member Rail Four-way Equal Load Type JR CATALOG No.137-5E Structural Member Rail, Four-way Equal Load Type LM Guide JR Upper plate LM rail LM block Endplate End seal Grease nipple Side

More information

NEW Compact series. New KSF10 Size, Now Available Top Cover Type / Open Cover Type Lineup. For details, visit THK at Compact Series KSF

NEW Compact series. New KSF10 Size, Now Available Top Cover Type / Open Cover Type Lineup. For details, visit THK at   Compact Series KSF NEW ompact series ompact Series New 1 Size, Now vailable Top over Type / Open over Type For details, visit THK at www.thk.com information is updated regularly on the THK website. TLOG No.396-1E-EU ELETRI

More information

2-9 RG Series High Rigidity Roller Type Linear Guideway

2-9 RG Series High Rigidity Roller Type Linear Guideway G99TE17-136 2-9 High Rigidity Roller Type Linear Guideway 2-9-1 Advantages and features The new RG series from Hiwin features a roller as the rolling element instead of steel balls. The roller series offers

More information

Features of the Cam Follower

Features of the Cam Follower 507E Features and Types Features o the ring Seal Side plate Stud Needle roller Cage Fig.1 Structure o Model CF UU-A Structure and Features The is a compact and highly rigid bearing with a shat. It contains

More information

Roller. Roller. Caged Roller LM Guide. Roller Cage Effect Ultra-super-high Rigidity SRG/SRN. CATALOG No.270-7E

Roller. Roller. Caged Roller LM Guide. Roller Cage Effect Ultra-super-high Rigidity SRG/SRN. CATALOG No.270-7E Roller Roller Caged Roller LM Guide Roller Cage Effect Ultra-super-high Rigidity SRG/SRN CATALOG No.2-E Roller Cage Effect According to the history of rotary ball bearings, which used balls as the rolling

More information

Roller Compliant with New Accuracy Standards Caged Roller LM Guide Roller Cage Effect Ultra-super-high SRG/SRN Rigidity

Roller Compliant with New Accuracy Standards Caged Roller LM Guide Roller Cage Effect Ultra-super-high SRG/SRN Rigidity Compliant with New Accuracy Standards Roller Roller Caged Roller LM Guide Roller Cage Effect Ultra-super-high Rigidity SRG/SRN For details, visit THK at www.thk.com Product information is updated regularly

More information

Cross Roller Guide/Ball Guide General Catalog

Cross Roller Guide/Ball Guide General Catalog General Catalog A Product Descriptions Features and Types... A7-2 Features of the.. A7-2 Structure and Features... A7-2 Types of the.. A7-3 Types and Features... A7-3 Point of Selection... A7-4 Rated Load

More information

4mm(H)x8mm(W) Micro LM Guides

4mm(H)x8mm(W) Micro LM Guides 4mm(H)x8mm(W) Micro LM Guides US, EPC, Patent Pending CATALOG No.293E Micro LM Guides RSR3M/3N The micro size allows space-saving design. Can be used in various fields of industry including micro machines

More information

Precision Linear Pack

Precision Linear Pack Precision Linear Pack General Catalog A Technical Descriptions of the Products B Product Specifications (Separate) Features... Features of the Precision Linear Pack... Structure and features... Rated Load

More information

NR/NRS. LM Guide B-93. A Technical Descriptions of the Products (Separate) B Product Specifications

NR/NRS. LM Guide B-93. A Technical Descriptions of the Products (Separate) B Product Specifications R/RS Guide Product Specifications Dimensional Drawing, Dimensional Table s R-R and R-R... s RS-R and RS-R... s R-A and R-A... s RS-A and RS-A... s R- and R-... s RS- and RS-... Standard engt and aximum

More information

The Block Structure. Linear block SBG, SBS, SPG and SPS types are available. All blocks are dimensionally interchangeable.

The Block Structure. Linear block SBG, SBS, SPG and SPS types are available. All blocks are dimensionally interchangeable. Circular arc groove Two pint contact structure of circular arc groove. It keeps the function of self-aligning and smooth rolling performance. 45 angle of contact Four rows of circular arc groove contact

More information

NSK Linear Guides. Roller Guide RA Series. Extended series

NSK Linear Guides. Roller Guide RA Series. Extended series NSK Linear Guides A roller guide series employing advanced analysis technology offers super-high load capacity and rigidity. The RA series includes a complete lineup to handle a wide range of applications.

More information

Unfinished Shaft Ends Precision Ball Screw

Unfinished Shaft Ends Precision Ball Screw Standard Stock Models BIF, MDK, MBF and BNF Point of Selection Options Model No. Precautions on Use ccessories for ubrication Mounting Procedure and Maintenance B ead ngle ccuracy ccuracy of the Mounting

More information

LM Guide Actuator KR. For details, visit THK at CATALOG No E. Product information is updated regularly on the THK website.

LM Guide Actuator KR. For details, visit THK at  CATALOG No E. Product information is updated regularly on the THK website. LM Guide Actuator KR For details, visit THK at www.thk.com Product information is updated regularly on the THK website. CATALOG No.209-10E Integrated LM Guide and all Screw High-rigidity / High-precision

More information

LM Roller General Catalog

LM Roller General Catalog General Catalog A Product Descriptions Features and Types... A10-2 Features of the... A10-2 Structure and Features... A10-2 Types of the... A10-4 Types and Features... A10-4 Point of Selection... A10-6

More information

C-Lube Linear Way MV

C-Lube Linear Way MV -Lube Linear Way 49 50 -Lube Maintenance Free Series -Lube Linear Way Long term maintenance free compliant! The aquamarine end plate is the symbol of maintenance free. Designation of Identification Number

More information

KR15. LM Guide Miniature Actuator. KR Series Actuators with Integrated LM Guide and Ball Screw in a Compact Stainless Steel Body. CATALOG No.

KR15. LM Guide Miniature Actuator. KR Series Actuators with Integrated LM Guide and Ball Screw in a Compact Stainless Steel Body. CATALOG No. LM Guide Miniature Actuator KR1 KR Series Actuators with Integrated LM Guide and Ball Screw in a Compact Stainless Steel Body US, EPC Patent pending CATALOG No.76E LM Guide Actuator KR1 Miniature LM Guide

More information

12.4 Miniature Type, MSC MSD Stainless Steel Series

12.4 Miniature Type, MSC MSD Stainless Steel Series 12.4 Miniature Type, MSC MSD Stainless Steel Series A. Construction Carriage End Cap MSC Standard Type End Seal Rail MSD Wide Type Ball Retainer Bottom Seal 45 45 B. Characteristics MSC st ows with Gothic-arch

More information

BERG AB Тел. (495) , ф. (495)

BERG AB Тел. (495) , ф. (495) www.thk.ru BERG AB thk@thk.ru Тел. (495)-727-22-72, ф. (495)-223-371 Advantages of Caged BallTM Technology High speed performance Low noise design, Long service life, Long-term maintenance-free operation

More information

Linear Bushing General Catalog

Linear Bushing General Catalog General Catalog A Technical Descriptions of the Products B Product Specifications (Separate) Features and Types... Features of the... Structure and features... Dedicated Shafts for Model LM... Standard

More information

Ball Rail Systems RE / The Drive & Control Company

Ball Rail Systems RE / The Drive & Control Company Ball Rail Systems RE 82 202/2002-12 The Drive & Control Company Rexroth Linear Motion Technology Ball Rail Systems Roller Rail Systems Standard Ball Rail Systems Super Ball Rail Systems Ball Rail Systems

More information

Linear Guideways QH Series

Linear Guideways QH Series G99TE17-136 2-6 Quiet Linear Guideway, with SynchMotion TM Technology The development of HIWIN-QH linear guideway is based on a four-row circular-arc contact. The HIWIN-QH series linear guideway with SynchMotion

More information

2-3 Miniature MGN/MGW Series Features of MGN Series

2-3 Miniature MGN/MGW Series Features of MGN Series 54 G99TE08-0405 2-3 Miniature MGN/MGW Series 2-3-1 Features of MGN Series 2-3-2 Construction of MGN Series Cap Block End cap End seal Grease nipple Ball Bottom seal Retainer Rolling Circulation System:

More information

G10TE HG Linear Guideway

G10TE HG Linear Guideway G10TE01-0310 I HG Linear Guideway Preface... 1 1... 1 1-1... 1 1-2... 2 1-3... 3 1-3-1 1-3-2 1-4... 4 1-4-1 1-4-2 1-4-3 1-4-4 1-4-5 1-5... 6 1-5-1 1-5-2 1-5-3 1-5-4 1-6... 9 1-7... 9 1-7-1 1-7-2 1-8...

More information

Crossed Roller Ways. Description of each series and Table of dimensions. Anti-Creep Cage Crossed Roller Way

Crossed Roller Ways. Description of each series and Table of dimensions. Anti-Creep Cage Crossed Roller Way Crossed Roller Ways Description of each series and Table of dimensions Crossed Roller Way Page - to -7 Anti-Creep Cage Crossed Roller Way Page - to - Crossed Roller Way Unit Page - to - In the table of

More information

Specifi cation Table. SSR-XW A 14.7 to to SSR-XV A 9.1 to to SSR-XTB A 14.7 to to 36.4

Specifi cation Table. SSR-XW A 14.7 to to SSR-XV A 9.1 to to SSR-XTB A 14.7 to to 36.4 Types of s THK offers a wide array of types and dimensions with s as standard so that you can select the optimal product for any application. With the unit structure of each model, you can easily obtain

More information

The Classification Chart of PMI Linear Guideways

The Classification Chart of PMI Linear Guideways 1 The Characteristics of MI s The Classification Chart of MI s 2 (1) igh positioning accuracy, high repeatability The MI linear guideway is a design of rolling motion with a low friction coefficient, and

More information

Miniature Linear Guideway MSC Stainless Steel Series

Miniature Linear Guideway MSC Stainless Steel Series Supreme Performance of High Precision 1 Construction Carriage End Cap End Seal Rail Ball Retainer Bottom Seal 4 4 2 Characteristics MSC stainless steel series are applied two rows with Gothicarch groove

More information

C-Lube Linear Way MLV MLV

C-Lube Linear Way MLV MLV -Lube Linear Way 9 0 -Lube Maintenance Free Series -Lube Linear Way Long term maintenance free compliant! The aquamarine end plate is the symbol of maintenance free. Identification Number and Specification

More information

Linear Bushing. General Catalog A-523

Linear Bushing. General Catalog A-523 Linear Bushing General Catalog A Technical Descriptions of the Products B Product Specifications (Separate) Features and Types... Features of the Linear Bushing... Structure and features... Dedicated Shafts

More information

Precise Stable Durability High Rigidity. Meet the Multi-Demand of Accuracy and Efficiency

Precise Stable Durability High Rigidity. Meet the Multi-Demand of Accuracy and Efficiency Precise Stable Durability High Rigidity Meet the Multi-Demand of Accuracy and Efficiency Linear Guideway B1-1 The Characteristics of PMI Linear Guideways High positioning accuracy, high repeatability

More information

Contamination Protection Accessories

Contamination Protection Accessories For the supported models, see the table of options by model number on. For the M block dimension with QZ attached, see to. For notes regarding how to handle the QZ, see. feeds the right amount of lubricant

More information

Roller Follower General Catalog

Roller Follower General Catalog General Catalog A Product Descriptions Features and Types... A20-2 Features of the... A20-2 Structure and Features... A20-2 Types of the... A20-3 Types and Features... A20-4 Point of Selection... A20-6

More information

The Characteristics of PMI Linear Guideways

The Characteristics of PMI Linear Guideways Linear Guideway 1 The Characteristics of PMI Linear Guideways (1) High positioning accuracy, high repeatability The PMI linear guideway is a design of rolling motion with a low friction coeffcient, and

More information

Linear Guideways MG Series

Linear Guideways MG Series 52 2-3 - Miniature Linear Guideway 2-3-1 Features of MGN Series 1. Tiny and light weight, suitable for miniature equipment. 2. All materials in special grade of stainless steel for anti-corrosion size

More information

Linear Way F LWF Ⅱ 133 Ⅱ 134

Linear Way F LWF Ⅱ 133 Ⅱ 134 Linear Way F 33 34 Linear Way F umber and Specification xample of an identification The specification of series is indicated by the identification. Indicate the identification, consisting of a model, dimensions,

More information

C-Lube Linear Way MUL Linear Way U MUL LWU

C-Lube Linear Way MUL Linear Way U MUL LWU C-Lube Linear Way Linear Way U 1 16 C-Lube Maintenance Free Series C-Lube Linear Way long term maintenance free supported! The aquamarine end plate is the symbol of maintenance free. Identification umber

More information

(1) High positioning accuracy, high repeatability. (2) Low frictional resistance, high precision maintained for long period

(1) High positioning accuracy, high repeatability. (2) Low frictional resistance, high precision maintained for long period Linear Guideway 1 The Characteristics of PMI Linear Guideways (1) igh positioning accuracy, high repeatability The PMI linear guideway is a design of rolling motion with a low friction coeffcient, and

More information

Linear Guideway. Technical Information.

Linear Guideway. Technical Information. Linear Guideway Technical Information www.hiwin.com.tw Linear Guideways Technical Information Index Preface...1 1. General Information...1 1-1 Advantages and features of Linear Guideway...1 1-2 The principles

More information

Linear Way F. Linear Way F series. Linear Way F LWFF LWFH. Interchangeable. Wide structure. Flange type and block type.

Linear Way F. Linear Way F series. Linear Way F LWFF LWFH. Interchangeable. Wide structure. Flange type and block type. ide Rail Type Linear ay Linear ay LHLLS U.S. PATTD Linear ay is a linear motion rolling guide, featuring a wide track rail along which a highly rigid slide unit performs endless linear motion. A large

More information

Тел. (495) Miniature LM Guide Actuators Featuring Caged Ball Technology

Тел. (495) Miniature LM Guide Actuators Featuring Caged Ball Technology Miniature LM Guide Actuators Featuring Caged all Technology Caged all Technology Offers Long life and long-term, maintenance-free operation Excellent high speed performance Excellent Sliding Smooth Motion

More information

Profi le rail guides LLR

Profi le rail guides LLR Profi le rail guides LLR Content The SKF brand now stands for more than ever before, and means more to you as a valued customer. While SKF maintains its leadership as the hallmark of quality bearings throughout

More information

Caged Ball LM Guide Actuator SKR

Caged Ball LM Guide Actuator SKR Caged all LM Guide Actuator SKR For details, visit THK at www.thk.com Product information is updated regularly on the THK website. CATALOG No.309-9E Integrated LM Guide and all Screw High-rigidity / High-precision

More information

Miniature LM Guide Actuators Featuring Caged Ball Technology

Miniature LM Guide Actuators Featuring Caged Ball Technology Miniature LM Guide Actuators Featuring Caged all Technology Caged all Technology Offers Long life and long-term, maintenance-free operation Excellent high speed performance Excellent Sliding Smooth Motion

More information

High-Speed Ball Screw with Ball Cage. Low noise Long-term, maintenance free operation Low torque fluctuation DN value 130,000 SBN. CATALOG No.

High-Speed Ball Screw with Ball Cage. Low noise Long-term, maintenance free operation Low torque fluctuation DN value 130,000 SBN. CATALOG No. High-Speed Ball Screw with Ball Cage Low noise Long-term, maintenance free operation Low torque fluctuation DN value 130,000 SBN CATALOG No.273-2E High speed ball screw with caged ball technology SBN Pipe

More information

Linear Guideways ov -linear -guidew ays-divider - U pdated

Linear Guideways ov -linear -guidew ays-divider - U pdated Linear Guideways ov-linear-guideways-divider - Updated - 11-01-2017 163 Linear Guideways Linear Guideways Introduction L1016 Linear guideways Linear guideways are widely used throughout industry for heavy-duty

More information

Linear Guideway General Catalog

Linear Guideway General Catalog General Catalog General Catalog Index TY AG Contents Technical roducts TY AG 1 2 3 4 5 6 7 8 6 7 1 11 11 11 12 12 13 14 15 18 19 1. The Characteristics of MI s 2. The Classifi cation Chart of MI s 3. The

More information

NEW LM Actuator. US Only. Optimal for high speed and long stroke Long term maintenance-free operation is actualized Lightweight, compact structure

NEW LM Actuator. US Only. Optimal for high speed and long stroke Long term maintenance-free operation is actualized Lightweight, compact structure NEW LM Actuator Optimal for high speed and long stroke Long term maintenance-free operation is actualized Lightweight, compact structure TY US Only CATALOG No.352E Structure of Model TY This belt drive

More information

...components in motion. Miniature Linear Guideways

...components in motion. Miniature Linear Guideways ...components in motion Miniature Linear Introduction Miniature linear guideway systems are widely used throughout industry for precise, compact applications. Precise and Stainless The gothic arch shape

More information

LM Guide Ultra-heavy-load, High-rigidity LM Guide Models NR and NRS Structure and Features Improved damping capacity Highly rational LM Guide

LM Guide Ultra-heavy-load, High-rigidity LM Guide Models NR and NRS Structure and Features Improved damping capacity Highly rational LM Guide a-0 a 1 a-1 a-2 a 3 R a-3 C CL=0.8C CT=0.48C C0 C0L=0.1C0 C0T=0.45C0 1.0 2 0.5 1 a-4 UU SS DD ZZ KK SSHH DDHH ZZHH KKHH a 5 15 1 23 24 29 42 42 42 51 a-5 48 0 86 100 126 145 156.5 31 35 40.5 49 5.5 64

More information

Introduction of Linear Guides

Introduction of Linear Guides [ New Product ] Introduction of Linear Guides Masaki KAGAMI* Keisuke KAZUNO* Man has moved heavy loads since ancient times using rotation and linear movement or a combination of both. Linear guides based

More information

511E. Ball Screw General Catalog

511E. Ball Screw General Catalog Ball Screw General Catalog A Ball Screw General Catalog A Product Descriptions Types of Ball Screws... A15-6 Point of Selection... A15-8 Flowchart for Selecting a Ball Screw... A15-8 Accuracy of the Ball

More information

Cost Effective Screw series

Cost Effective Screw series Cost Effective Screw series Ball Screws Compliant with the New Accuracy Standards New Series CES (Pronounced sees ) Simple-Nut Type BIF Double-Nut Type BNFN (build to order) Single-Nut Type BNF (build

More information

1.1. Types of Lubricants Grease Lubrication Oil Lubrication

1.1. Types of Lubricants Grease Lubrication Oil Lubrication a-2 a-2 a 3 a-3 a-4 a 5 a-5 19.6 MPa max 0.6 cc/stroke 70-g bellows cartridge 235 mm (excluding the nozzle) 480 g (including the nozzle; excluding grease) a-6 a 7 a-7 LF-A (PT1/8) L=20, L1=, F=2, C=, D=

More information

10 Thrust ball bearings

10 Thrust ball bearings 10 Thrust ball bearings Designs and variants.............. 1010 Single direction thrust ball bearings... 1010 Double direction thrust ball bearings.. 1010 Cages............................ 1010 Bearings

More information

114 NOSE SEIKO CO.,LTD NOSE SEIKO CO.,LTD

114 NOSE SEIKO CO.,LTD NOSE SEIKO CO.,LTD 114 NOSE SEIKO CO.,LTD NOSE SEIKO CO.,LTD 115 and Part Code Applicable axis diameter Feature Part Code 5 ~ 3 General purpose cam follower with screwdriver groove on the stud head. Available with stainless

More information

Profile rail guides LLT

Profile rail guides LLT Profile rail guides LLT Contents The SKF brand now stands for more than ever before, and means more to you as a valued customer. While SKF maintains its leadership as the hallmark of quality bearings throughout

More information