Actuator Products Rodless Cylinders. GDL Series. Material specifications. Specifications OSP-P. Series. Series P1X. Series P1Z.

Transcription

1 Catalog PDN1-3US High Performance : (s FDC12HP-... thru FDC45HP-...) The High Performance series is the basis for s development, which is used in the majority of applications. High Performance guides consist of 8 axial needle roller bearings, running on precision polished and hardened alloy spring steel guideways. These guide bearings are grease packed and shielded, while offering the highest load and moment rating capacities within the product line. Standard Performance : (s FDC12SP-... thru FDC45SP-...) The Standard Performance series is intended for minor loads and moments for particularly economical guidance solutions. Standard Performance guides consist of 8 radial ball roller bearings, running on precision polished and hardened alloy spring steel guideways. These guide bearings are grease packed and sealed, while offering the lowest load and moment ratings available within the product line, with the exception of the Grease-Free and the Anti-Friction / Corrosion Resistant series. Standard Performance series is the second most commonly used guides for various applications and also provides excellent running behavior. Material specifications Guideways s / rollershoes / top plates Rollers Aluminum alloy Hardened high alloy spring steel Aluminum alloy earing steel / Stainless steel bearing steel P1 Specifications Characteristic Unit Description Full profile wipers Acceleration and deceleration m/s 2 (ft/sec 2 ) Rollershoes and cassette are provided with snap-on full profile wipers. The snap-on full profile wipers are easily replaceable with available wipers kits. 4 m/s 2 maximum (131 ft/s 2 maximum) Guide installation Possible in any position. s can be adjusted at the factory or by the customer. Drag adjustment set screw Rollershoes can be set-up by the customer to incorporate the drag adjustment set screw feature. The drag adjustment set screw components are supplied with each pair of rollershoes. Standard lubrication Lifetime lubrication with standard grease-packed roller bearings. Speed m/s (ft/s) Up to 1 m/s (or up to 33 ft/s) earing types Steel axial needle, Specials on request (ex: anti-magnetic, grease free, high dynamics) - consult factory Operating temperature C (F) -1 C to 8 C (14 F to 176 F) temperature range Specials available length cassettes and rollershoes for 1 piece lots minimum. Keyed butt-jointed rail sections up to 4mm. Solid continuous length rails between 4. Offset or non-standard dimensions on opposite ends of cut rails. Integrated metal scraper with standard full profile wiper currently available. underside blind mounting holes. 258

2 Catalog PDN1-3US with double sided rail as fs t2 min. D2 z x L12 d2 L12 L max. = 4 Drag adjustment set screw Dimensions for both standard FDC version guides Ls 5 h3 Fixed side with respect to dim. e h11 x 45 t3 Datum side with depth groove Length Ls S h3 h9 as d2 D2 e fs h8 h1 h11 e S ±.15 N1 h1 h8 h9 ±.1 min. L12 t2 t3 N M M M M M M12 Dimensions for both underside mounting hole FDC version guides (Ref. ordering instructions) Length Ls S h3 h9 as d2 D2 e fs h8 h1 h11 min. L12 t2 t3 N M M M M M M12 Roll -AXIS -AXIS Y-AXIS P1 Y F X F X Y F Y Y Y-AXIS X-AXIS X F X X-AXIS Y X F Y F X MOCX, MCX MOCY, MCY MCO, MC Load & moment rating capacities (for cassettes on double sided rail) Dynamic load rating C (N) Static load rating Co (N) Static moment rating capacities: Roll Mocx Mocy Mocz Dynamic moment rating capacities: Roll Mcx weight (kg) weight (kg) series High performance series FDC12HP FDC15HP FDC2HP FDC25HP FDC35HP FDC45HP-... Mcy Mcz 259

3 Catalog PDN1-3US Aluminum roller guides High performance cassettes with lock device Special cassette types The locking cassette with star grip handle can be stopped at any desired location on the rail. The clamping device does not exert forces on the rail guideways. The clamping device is used in fixtures which are movable manually, clamping and stop ledgers, feeding of tools and work pieces. Also available with L-ratchet handle. Star grip handle dimensions Øa b h Clamp force Part numbers star grip knob 12 N/A FDC15HP FDC2HP FDC25HP FDC35HP FDC45HP-2, Force (N) with normal manual tightening. L-ratchet handle dimensions End of stroke stop screws l b h Clamp force Part numbers L-ratchet handle 12 N/A FDC15HP FDC2HP FDC25HP FDC35HP FDC45HP-1 P1 accessories The stop screws are scre wed into threads (op tion) on the gui de rails. The end of stroke stop ping energy is reduced by a rubber cap. With guide rails whe re the is less than the standard minimum, we off set the mounting hole by half of its diameter. Note: er must drill and tap the holes for the stop screws. Ød ØD K min. P Order number 12 M A 15 M A 2 M A 25 M A 35 M A 45 M A mounting screw covers Cylindrical screw DIN912 Ø D Order number Ma te ri al: We ar re si stant pla stic, re si stant to oil and aging. Moun ting: Put a pla stic pla te on top and pound in uniform ly. Remo ve re si du al burrs with a soft brush or fingernail. Note: Use respective order numbers for ordering separately or include in rail part number. 12 M A 15 M A 2 M A 25 M A 35 M A 45 M A 26

4 Catalog PDN1-3US Aluminum roller guides Version with wipers Integrated into an additional cover, a felt wiper is saturated with oil. Although dependent on the degree of contaminants, these wipers last for Order numbers for replacement wiper kits some 6km, after which the felt wipers can either be washed or replaced. For optimal cassette rolling performance, all holes in the guide rails should be filled with the plastic rail mounting screw covers. with full profile snap-on wipers Respective FDC series and size order number *wiper kits are sold in pairs NOTE: Use respective order numbers for ordering separately as replacements, or specify in cassette part number. Full profile snap-on wiper s keyed butt-jointed rail option GUIDELINE rails can be precisely fastened together using a factory offered keyed butt-joint option for continuous rail lengths, as shown in Figures 1 & 2. Two rail sections are clamped together with mating round bar stock pieces that seat tangent to both rail section guideways on each side of the rail. While the rail sections are clamped together, a keyway slot is machined in the top and bottom sides of the rail, across the butt- joint. Screw holes are then drilled through the rail inside the keyway slot, so the opposing keyways can be drawn together tightly with screws. The round bar stock clamp is then removed, providing a rigid and well aligned keyed butt-joint. The keyed butt-joint option provides optimum alignment of all guideways from one rail section to the next. This allows for optimum smooth guidance of the cassette bearings, while crossing rail butt-joints. The keyed butt-jointed rail option is currently available in the FDR version 25, 35, & 45 mm rail sizes. For a keyed buttjoint on rail sizes 25, 35 or 45 mm, specify P/N:# -JK Consult factory for other size possibilities. Figure 1 Figure 2 coupled with structural aluminum extrusion material and OSP-E actuator Figure 3 linear guides couple well with various structural aluminum extrusions and Parker-Origa and OSP-E actuators. Mounting can be easily accomplished using standard fasteners and mounting brackets. See Figure 3 above. P1 261

5 Catalog PDN1-3US Ordering Information / Part Numbering System for s F D R 1 2 H Double sided rail FD guide* R *Stocked Item Standard 1 2* 1 5* 2 * 2 5* 3 5* 4 5* Guideway Material High performance H alloy steel* S Stainless steel Coatings Anodized aluminum* Dimension?? Equal on both sides* Actual dimension (mm)** ** As measured from left side while viewing the depth groove line. Mounting Holes Topside thru hole* Underside blind 1 thread Screw Covers None* 1 Yes* Note: Quantity supplied to cover all rail holes. Long Joining Option None* Keyed butt joint (size only) 2 Unkeyed butt joint Length (mm) Note: Maximum length is 4 meters on 12. Ordering Information / Part Numbering System for s F D C 1 2 H P P1 Double sided FD rail cassette* (standard C Standard 1 2* 1 5* 2 * 2 5* 3 5* 4 5* earing Options Axial needle - high HP performance alloy steel* Single row radial ball - SP standard performance - alloy steel* Factory** (consult factory Grease High performance* Lubrication Options None* ** Coatings Anodized and standard hardware* Anodized and 1 stainless steel hardware* Mounting Holes Topside threaded thru* Underside 1 hole thru (unthreaded) Underside hole 2 thru (threaded) Locking Mechanism None* 1 L ratchet handle* 2 Star grip handle* * Locking mechanism only available on FD size 15 thru 45 with Axial Needle earing - High Performance - Alloy Steel. Adjustment None* Adjusted 1 to specific rail* Length Normal length* (consult factory)** Wiper Options With felt wipers* 1 Without* With felt wipers 2 and scrapers* **Stocked Item **Minimum Order Quantity Required (consult factory) 262