Photometric Test Report

Transcription

1 Photometric Test Report Relevant Standards IES LM ANSI C UL Prepared For Revolution Lighting Technologies, Inc 2280 Ward Ave. Simi Valley, CA Roman Sukharev, (877) , Test Laboratory: UL-CCIC Company Limited Test Laboratory Address: 2, Chengwan Road, Suzhou Industrial Park, Suzhou China Catalog Number 15A512 Project Number Report Number _5 Test Date 1/18/2018-1/24/2018 Issue Date 3/6/2018 Revision Date Prepared By Approved By The results contained in this report pertain only to the tested sample. This report shall not be reproduced, except in full, without written approval of Underwriters Laboratories. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the U.S. Government. UL Report Number _5 Page 1 of 14

2 1.0 Test Summary DLC Technical Requirements v4.2- issued Requirement Category Test Method Requirements Test value Results (Fail/Pass) Minimum Light Output (lm) IES LM lm/ft Pass Minimum Bare Lamp Output (lm) IES LM N/A N/A N/A Spacing Criteria (0-180 ) IES LM N/A N/A N/A Spacing Criteria ( ) IES LM N/A N/A N/A Zonal Lumen Requirement 1 (20-60 ) IES LM % 69.1% Pass Zonal Lumen Requirement 2 IES LM N/A N/A N/A Minimum Luminaire Efficacy (lm/w) IES LM Pass Minimum Bare Lamp Efficacy (lm/w) IES LM N/A N/A N/A Alowable CCTs* (K) Minimum CRI IES LM ANSI C IES LM CIE ± Pass L70 Lumen maintenance (hours) IES TM Pass L90 Lumen maintenance (hours) IES TM Pass Power Factor ANSI C Pass Total Harmonic Distortion (A%) ANSI C % 4.75% Pass In-Situ Temperature Measurement Test for LED UL Pass In-Situ Temperature Measurement Test for Driver UL Pass Minimum Luminaire Warranty (years) N/A 5 5 Pass Pass UL Report Number _5 Page 2 of 14

3 2.0 Test List Test Item Test Test Date Model Number Tests Conducted By 1 Integrating Sphere Test for the Lower CCT 1/22/ A Gavin Yang 2 Integrating Sphere Test for the Higher CCT 1/22/ A Gavin Yang 3 Goniophotometer Test 1/18/ A Gavin Yang 4 THD and PF Test 1/24/ A Gavin Yang 5 In-Situ Temperature Measurement Test 1/24/ A Gavin Yang Remark (if any) 1. UL test equipment information is recorded on Meter Use in UL s Aurora database. UL Report Number _5 Page 3 of 14

4 3.0 Production Description Luminaire Description: Direct Linear Ambient Luminaires Model Number: 15A Rated Voltage: V Frequency: 50/60Hz LED Package: STWxA2PD-xx Family Model and Variation: 15A Remark: Photos of Luminaire Characteristics Model Number CCT (K) Light Output (lm) Power (W) Luminious Efficacy (lm/w) 15A A A UL Report Number _5 Page 4 of 14

5 4.0 LM-79 Measurement and Test Results 4.1 Integrating Sphere Test for the lower CCT Model No. 15A Sample ID Opreate time (Min.) 90 Stabilization time (Min.) 45 Test Method 1.The sample was tested according to the IES LM Photometric paramters were measured using an integrating sphere, a spectroradiometer and software. The ambient temperature condition inside the sphere was maintained at 25º C ± 1º C.The reference standard lamp is rated current 2.6A omni-directional Incandescent lamp and was calibrated by china seprei laboratory. 3.The sample measurements were made using a spectroradiometer connected by a fiber optic cable and detector through the detector port of the integrating sphere. Coating reflectance of the integrating sphere was 90% to 98%.Photometric measurement conditions was using 4π geometry.the self-absorption factor is applied in the final test result.the sample was operated at rated voltage and was stabilized before measurement. Chromaticity coordinates, correlated color temperature and color rendering index were calculated from the spectral radiant flux measurements taken at 1 nm intervals over the range of 380 to 780 nm. Integrating Sphere Test Conditions Temperature Voltage (Vac) Frequency (Hz) Current (A) Power (W) Power Factor Current THD % Test Results CCT (K) CRI (Ra) Duv Luminous Flux Luminous Luminous (lm) Efficacy (lm/w) Efficacy (lm/ft) UL Report Number _5 Page 5 of 14

6 4.0 LM-79 Measurement and Test Results 4.2 Integrating Sphere Test for the higher CCT Model No. 15A Sample ID Opreate time (Min.) 90 Stabilization time (Min.) 45 Test Method 1.The sample was tested according to the IES LM Photometric paramters were measured using an integrating sphere, a spectroradiometer and software. The ambient temperature condition inside the sphere was maintained at 25º C ± 1º C.The reference standard lamp is rated current 2.6A omni-directional Incandescent lamp and was calibrated by china seprei laboratory. 3.The sample measurements were made using a spectroradiometer connected by a fiber optic cable and detector through the detector port of the integrating sphere. Coating reflectance of the integrating sphere was 90% to 98%.Photometric measurement conditions was using 4π geometry.the self-absorption factor is applied in the final test result.the sample was operated at rated voltage and was stabilized before measurement. Chromaticity coordinates, correlated color temperature and color rendering index were calculated from the spectral radiant flux measurements taken at 1 nm intervals over the range of 380 to 780 nm. Integrating Sphere Test Conditions Temperature Voltage (Vac) Frequency (Hz) Current (A) Power (W) Power Factor Current THD % Test Results CCT (K) CRI (Ra) Duv Luminous Flux Luminous Luminous (lm) Efficacy (lm/w) Efficacy (lm/ft) UL Report Number _5 Page 6 of 14

7 5.0 LM-79 Measurement and Test Results Model No. 15A Sample ID Opreate time (Min.) 90 Stabilization time (Min.) 45 Test Method 1.The sample was tested according to the IES LM Photometric paramters were measured using a type C goniophotometer and software. 3.The ambient temperature shall be maintained at 25 C ± 1 C, measured at a point not more than 1 m from the sample and at the same height as the sample.the reference standard lamp is rated current 3.865A omni-directional Incandescent lamp and was calibrated by china seprei laboratory. 4.The samples were operated at rated voltage and was stabilized before measurement. Luminous flux, luminaire efficacy, zonal lumen were calculated from the software taken at 1 vertical intervals and 22.5 horizontal intervals..photometric distance was more than five times of the largest dimension of the test SSL product. Goniophotometer Test Conditions Temperature Voltage (Vac) Frequency (Hz) Current (A) Power (W) Power Factor Current THD Orientation % Horizontal Test Result Zonal Lumen Zonal Lumen Field Angle Beam Angle Luminous Flux Requirement 1 Requirement 2 (10%) (50%) Efficacy (lm) (0-60 ) Horizontal Spread Vertical Spread Horizontal Spread Vertical Spread (lm/w) % N/A SC SC 0~ ~270 N/A N/A 1 4 UL Report Number _5 Page 7 of 14

8 5.0 Goniophotometer Test (Cont'd) Light Distribution Curve IsoCandela Plot 2 UL Report Number _5 Page 8 of 14

9 5.0 Goniophotometer Test (Cont'd) Zonal Lumen Summary Lumens Per Zone 3 UL Report Number _5 Page 9 of 14

10 5.0 Goniophotometer Test (Cont'd) Intensity Data(cd) UL Report Number _5 Page 10 of 14

11 6.0 THD and PF Test Model No. 15A Sample ID Test Method 1. The samples were tested according to the ANSI C The ambient temperature condition was maintained at 25º C ± 1º C. The sample measurement was made using a digital power meter and power supply. The sample was operated at rated voltage and stabilized before measurement. The total harmonic distortion were calculated from thedigital power meter. Test Results Temperature Voltage (Vac) Frequency (Hz) Current (A) Power (W) Power Factor Current THD % 1 1 UL Report Number _5 Page 11 of 14

12 7.0 In-Situ Temperature Measurement Test Model No. 15A Sample ID Test Method 1. In-Situ Temperature Measurement Test is conducted according to the UL , Section The testing was conducted in a room with ambient temperature of 25 C ± 5 C. The apparatus construction followed those described in UL for normal temperature testing. Thermocpuples were placed on the LED package in the locations indicated by LM-80 report. The temperature was recorded after the lamp was operated by 3.5 hours in stability or by 7.5 hours. In-Situ Temperature Measurement Test Conditions Temperature Voltage (Vac) Frequency (Hz) Current (A) Power (W) Power Factor Orientation Horizontal Test Results(LED) Temperature for Lighting source Manufacturer Thermocouple Declared Current Location Test Result Test Result (ma) Column (Correct to 25 C) TMP of LEDs Ambient Temperature N/A Test Results(Driver) Temperature for Driver Thermocouple Location Test result Test result Column (Correct to 25 C) TMP of Driver Ambient Temperature LED Model Number Driver Model Number LM-80 Limit Current (ma) LM-80 Limit Temp STWxA2PD-xx Driver Limit Temp SIE40-I W D1 R 90 UL Report Number _5 Page 12 of 14

13 7.0 In-Situ Temperature Measurement Test (Cont'd) Test Photos for Ts Point of LED Packages & Tc Point of Driver 2 2 UL Report Number _5 Page 13 of 14

14 ****** END OF REPORT. THIS PAGE INTENTIONALLY LEFT BLANK ****** UL Report Number _5 Page 14 of 14