Certified quality. Versatile and economical. GETO Van body kit. TITGEMEYER Tf1495GB(1217)1

Transcription

1 Certified quality Versatile and economical TITGEMEYER

2 body kits are supplied to the bodybuilder ready for assembly, on transport racks that are easy to handle and store. Short unloading times, secure temporary storage and shortened assembly time ensure cost savings for the bodybuilder. 2 L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

3 the body kit that covers all the options Thanks to its innovative design and assembly principle, the body kit is sure to impress: by using state-of-the-art bonding technology, the design ensures certified quality together with an elegant appearance. Standard kits are available with either plywood, Sandwich, ultra, ferro or clamped aluminium panels. The external appearance of the is very impressive: free of any rivets or bolts, the walls and doors have smooth surfaces.the complete body kit is supplied powder-coated in MB 947 (arctic white). On request, can, of course, also be supplied unfinished if it is to be specifically painted on-site. The flush edges of the side walls, bulkhead and cantrails as well as the concealed seals in the corner posts and cantrails, all enhance the kit s attractive appearance. Quick and easy assembly Assembly of the body kit only requires mechanical fastening inside the body. All assembly holes are provided. There is no need to seal the individual components: only the front and rear corner castings need to be bonded by the bodybuilder. Cargo control pans and tracks are already installed, exactly where you need them. L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com 3

4 Bulkhead and side walls Available in plywood, sandwich, ultra, ferro or clamped aluminium Walls have an integrated kick strip Fittings Cargo control pans and tracks 6 mm wooden lining (only for standard aluminium) Doors and flaps in the side walls Doors - leaf or 2-leaf Flaps with or without gas springs, opening up or down 4 L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

5 Roof Roof frame Aluminium cantrail Steel cross member, white coating Roof skin is GRP (translucent) or aluminium sheeting (bonded), additionally secured using a clip system. Roof fittings GRP polyester roof light (in aluminium roof) Ceiling lights Sandwich roof mm Aluminium cantrail Roof fittings Roof lights Rear door frame Steel, galvanised Corner pillar width, mm Bottom member height, depending on floor thickness (8, 2, 24, 27), from 0 to 0 mm, Bottom member height when the body has a tail-lift flap is always 70 mm Header for fitting roller shutter: Header height to suit type of roller shutter Upper facing 0 20 mm Rear options Doors Aluminium, double-leaf, with one or two recessed or external locks (steel, galvanised) Tail-lift flap Aluminium, with gas springs Tail lift sealing system with guides, plus handrail on the right Roller shutter, e.g. C4 light, partly prepared L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

6 Wide range of bodywork options Whether for short or long distances, for garment transport or for use as a distribution van, offers a comprehensive range of bodywork options. The length, width and height can all be supplied in 2 mm increments as shown below. Lenght L Width B Height H Plywood 4 mm Plywood 7 mm Plywood 20 mm Sandwich 2 mm Sandwich 2 mm reinforced Ultra 4 mm Ultra 7 mm Ultra 20 mm Ultra 20 mm Ferro mm Clamped aluminium (28 mm without internal lining) offers plenty of design freedom to satisfy individual customer requirements. 6 L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

7 body kit Body kit description s Overview Plywood Sandwich Ultra FERRO Aluminium 2 side walls bulkhead roof rear frame with doors Material Wall thickness (mm) Rave flange height (mm) Steel kick strip (mm) fitted inside Powder coated finish Surface Pillar spacing (mm) Pillar material Material Wall thickness (mm) Rave height (mm) Steel kick strip (mm) fitted inside Powder coated finish Surface Pillar spacing (mm) Pillar material Type Material Wall thickness (mm) Cross member spacing (mm) Cantrail Powder coated finish of extrusions Type 2 doors Material Locking gear in right door Internal lining Plywood approx. 27 MB 947 (Arctic White) smooth Plywood 7 20 approx. 27 MB 947 (Arctic White) smooth one-piece, smooth GRP, translucent.8 rounded MB 947 (Arctic White) steel construction fitted in rear frame Aluminium, smooth bordered recessed, lockable galvanised steel/primed GFK-Sandwich 2 approx. 27 MB 947 (Arctic White) smooth GRP, Sandwich 2 approx. 27 MB 947 (Arctic White) smooth one-piece, smooth GRP, Sandwich rounded MB 947 (Arctic White) steel construction fitted in rear frame Aluminium, smooth bordered recessed, lockable galvanised steel/primed GFK-Sandwich approx. 27 MB 947 (Arctic White) smooth GRP, Sandwich 7 20 approx. 27 MB 947 (Arctic White) smooth one-piece, smooth GRP, translucent.8 rounded MB 947 (Arctic White) steel construction fitted in rear frame Aluminium, smooth bordered recessed, lockable galvanised steel/primed Steel, Sandwich approx. 27 RAL 900 smooth with joints Steel, Sandwich approx. 27 RAL 900 smooth with joints one-piece Steel, Sandwich rounded RAL 900 steel construction fitted in rear frame Aluminium, smooth bordered recessed, lockable galvanised steel/primed Aluminium 28 approx. 27 MB 947 (Arctic White) clamped panels Steel Aluminium 28 approx. 27 MB 947 (Arctic White) clamped panels Steel one-piece, smooth GRP, translucent.8 rounded MB 947 (Arctic White) steel construction fitted in rear frame Aluminium, smooth bordered recessed, lockable galvanised steel/primed L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com 7

8 Plywood, sandwich, body kit ultra and ferro rear door frame dimensions, weld-on type L B B2 L View from above B3 B = B-0 Internal dimensions Panelthickness Width B2 4 mm B 47 7 mm B 3 20 mm B 9 2 mm B 69 Lenght L2 L 2 L L 8 L 63 Side view Bottom member, standard Bottom member, tail-lift flap L Underside of cross member ca. 38 H 4 H2 83 Top of floor Top of floor recess 8/0 2/04 24/07 27/0 H3 H4 H 70 7, L = external length of roof from bulkhead roof corners to outer edge of rear frame header L2 = internal length between bulkhead kick strip and inner face of rear doors (tail-lift flap) L3 = overall external length from bulkhead roof corners to outer edge of door hinges B = overall width across roof corners B2 = internal width measured between the kick strips on the side walls B3 = clear aperture width through rear frame B = external width of rear fame H = external height from roof corners to bottom of side rave H2 = internal height from roof cross member to top of floor recess, floor thickness 8, 2, 24, 27 mm H3 = clear aperture height through rear frame H4 = overall height from top of roof to bottom of side rave / bottom of rear frame member H = clear aperture height through rear frame if tail-lift flap fitted = rear header: mm for doors with recessed door gear and for flap over tail-lift rear header: 98 mm for doors with external door gear 2 = height of rear frame bottom member depends on floor thickness Dimensions in mm 8 L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

9 Plywood, sandwich, ultra and ferro rear frame dimensions, bolt-on type View from above L3 220 B B2 - L Internal dimensions B3 B=B-0 Panelthickness 4 mm 7 mm 20 mm 2 mm Width B2 B 47 B 3 B 9 B 69 Lenght L2 L 2 L L 8 L 63 Side view Bottom member, standard Bottom member, tail-lift flap L H H2 H3 H4 ca. 38 H 2 Underside of cross member , /0 27/3 24/6 2/9 8/ Top of floor Top of floor recess L = external length of roof from bulkhead roof corners to outer edge of rear frame header L2 = internal length between bulkhead kick strip and inner face of rear doors (tail-lift flap) L3 = overall external length from bulkhead roof corners to outer edge of door hinges B = overall width across roof corners B2 = internal width measured between the kick strips on the side walls B3 = clear aperture width through rear frame B = external width of rear fame H = external height from roof corners to bottom of side rave H2 = internal height from bottom of roof to top of floor recess; floor thickness 8, 2, 24, 27, mm H3 = clear aperture height through rear frame H4 = overall height from top of roof to bottom of side rave / bottom of rear frame member H = clear aperture height through rear frame if tail-lift flap fitted = rear header: mm for doors with recessed door gear and for flap over tail-lift rear header: mm for doors with external door gear 2 = height of inside bottom member depends on floor thickness Dimensions in mm L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com 9

10 Clamped aluminium body kit rear door frame dimensions, weld-on type 62, L B B2 79 L2 28 B3 4 2 View from above B = B-0 Internal dimensions (without interior trim) Width B2 Lenght L2 B 7 L 66 Side view Bottom member, standard Bottom member, tail-lift flap L 2 H H2 40 Underside of cross member 3 Top of floor Top of floor recess H3 8/0 2/04 24/07 27/0 H4 H ca , L = external length of roof from bulkhead roof corners to outer edge of rear frame header L2 = internal length between bulkhead kick strip and inner face of rear doors (tail-lift flap) L3 = overall external length from bulkhead roof corners to outer edge of door hinges B = overall width across roof corners B2 = internal width measured between the kick strips on the side walls B3 = clear aperture width through rear frame B = external width of rear fame H = external height from roof corners to bottom of side rave H2 = internal height from roof cross member to top of floor recess, floor thickness 8, 2, 24, 27 mm H3 = clear aperture height through rear frame H4 = overall height from top of roof to bottom of side rave / bottom of rear frame member H = clear aperture height through rear frame if tail-lift flap fitted = rear header: mm for doors with recessed door gear and for flap over tail-lift rear header: 98 mm for doors with external door gear 2 = height of rear frame bottom member depends on floor thickness Dimensions in mm 0 L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

11 Clamped aluminium rear door GETO frame Van dimensions, body kit bolt-on type L3 220 B B2 - L View from above B3 B=B-0 Internal dimensions (without interior trim) Width B2 Lenght L2 B 7 L 66 Side view Bottom member, standard Bottom member, tail-lift flap L Underside of cross member 3 3 Top of floor Top of floor recess 7, /0 27/3 24/6 2/9 8/ H H3 H4 ca. 38 H 4 H L = external length of roof from bulkhead roof corners to outer edge of rear frame header L2 = internal length between bulkhead kick strip and inner face of rear doors (tail-lift flap) L3 = overall external length from bulkhead roof corners to outer edge of door hinges B = overall width across roof corners B2 = internal width measured between the kick strips on the side walls B3 = clear aperture width through rear frame B = external width of rear fame H = external height from roof corners to bottom of side rave H2 = internal height from bottom of roof to top of floor recess; floor thickness 8, 2, 24, 27, mm H3 = clear aperture height through rear frame H4 = overall height from top of roof to bottom of side rave / bottom of rear frame member H = clear aperture height through rear frame if tail-lift flap fitted = rear header: mm for doors with recessed door gear and for flap over tail-lift rear header: mm for doors with external door gear 2 = height of inside bottom member depends on floor thickness Dimensions in mm L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

12 body kit Side door dimensions L X H LB min. 204 ** min. 29 LB 4 40 *36 min. 24 min. Side door fitted without sill with header H2 min. 24 Side door fitted with sill with header min. 240 LH Header dimension min. 20 H Direction of travel LB LRB Sill dimension 83 min. 7 *min. 2 H2 L = external length of roof rom bulkhead roof corners to outer edge of rear frame header LH = clear height LB = clear width LRB = clear frame width H = external height from roof corners to bottom of side rave H2 = internal height from roof cross member to top of floor recess; floor thickness 8, 2, 24, 27 mm, and mm in the case of a bolted rear frame X = external dimension from roof corner to middle of door unit * = dimension with sandwich roof ** = dimension for door mounted fittings Front fitting dimension min. 2 X 20 L Rear fitting dimension min. 2 2 L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

13 body kit Flap dimensions L X min. 24 min. 24 Header dimension min. 20 *min. 2 L = external length of roof from bulkhead roof corners to outer edge of rear frame header LH = clear height LB = clear width LRB = clear frame width H min H = external height from roof corners to bottom of side rave H2 = internal height from roof cross member to top of floor recess; floor thickness 8, 2, 24, 27 mm and mm in the case of a bolted rear frame X = external dimension from roof corner to middle of door unit * = dimension with sandwich roof LB min. 204 LB 4 40 *36 H LRH LH ~ LB Direction of travel Flap fitted without sill with header H2 min. 240 Sill dimension min H2 Flap fitted with sill and header Front fitting dimension min. 2 X Rear fitting dimension min. 2 L L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com 3

14 body kit Subframe dimensions with and without adapter profile / weld-on rear frame Calculation of subframe dimensions Formula: Subframe dimensions = external length or width - adjustment dimension Description: Unterbaumaße = UL subframe length = UB subframe width External length = L external length of roof from bulkhead roof corners to outer edge of rear frame header External width = B overall width across roof corners Adjustment = Z corner adjustment dimension = Z2 rave adjustment = Z3 rear frame bottom member adjustment Sample calculation: Subframe length UL = L - Z - Z2 - Z3 Subframe width UB = B - (Z + Z) - (Z2 + Z2) Subframe dimensions of body kit with base assembly and bulkhead at the front and a rear door frame Rear frame bottom member Type A BA 8/70 BA 2/70 BA 24/70 BA 27/70 Rear frame bottom member Type B BA 8/0 BA 2/04 BA 24/07 BA 27/0 Subframe length UL with adapter profile L - 8, L - 8, L - 8, L - 8, With adapter profile for Frame subframe 2 Without adapter profile for in-house manufacture of subframe without adapter profile L - 67, L - 67, L - 67, L - 67, Subframe width UB B - 4 B - 4 B - 4 B - 4 Please note! Longitudinal members must be approx. 40 mm longer at the back than the length calculated for the subframe (rear frame bottom member recess). L (Z) BA BA 7, (Z2) 42, Subframe length UL Subframe length UL 4 96 (Z3) Type A Adapter profile 4 96 (Z3) Type B Direction of travel (Z) 7, (Z2) 0 B Subframe width UB 0 (Z) 7, (Z2) L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

15 body kit Subframe dimensions with adapter profile / bolt-on rear frame L (Z) 42, Adapter profile 7, (Z2) Subframe length UL Subframe length UL 03 (Z3) 03 (Z3) Direction of travel 0 B (Z) 7, (Z2) Subframe width UB Calculation of subframe dimensions Formula: Subframe dimensions = external length or width - adjustment dimension Description: Subframe = UL subframe length dimensions = UB subframe width External length = L external length of roof from bulkhead roof corners to outer edge of rear frame header External width = B overall width across roof corners Adjustment = Z corner adjustment dimension = Z2 rave adjustment = Z3 rear frame bottom member adjustment Subframe dimensions of body kit with base assembly and bulkhead at the front and a rear door frame Rear frame bottom member Type A BA 8/70 BA 2/70 BA 24/70 BA 27/70 Rear frame bottom member Type B BA 8/3 BA 2/3 BA 24/3 BA 27/3 Subframe length UL only with adapter profile L - 2, L - 2, L - 2, L - 2, Subframe width UB B - 4 B - 4 B - 4 B - 4 Please note! Longitudinal members must be approx. 40 mm longer at the back than the length calculated for the subframe (rear frame bottom member recess). BA Type A Sample calculation: Unterbaulänge UL = L - Z - Z2 - Z3 Unterbaubreite UB = B - (Z + Z) - (Z2 + Z2) BA Type B /0 27/ /9 8/2 (Z) 7, (Z2) L Phone: +49 (0) 4/ Fax: +49 (0) 4/ truckandtrailer@titgemeyer.com

16 Gebr. TITGEMEYER GmbH & Co. KG Hannoversche Straße 97 (Navigation: Hettlicher Masch 2) Osnabrück, Germany P.O. Box Osnabrück, Germany Phone: +49 (0) 4/ Fax: +49 (0) 4/ The technical specifications contained in this brochure are approximate and no guarantee is given as to their accuracy! Designs are subject to change. Our design proposals are non-binding! TITGEMEYER, GETO and are trademarks, registered trademarks or product names belonging to the respective title holder.