Table of Contents General Precautions Important Notice/Warranty Items Included In Kit Power Commander Tuning Tips Wiring Diagrams Optional Products

Transcription

1 DRY-3008, Dry Nitrous System w/stainless Line Table of Contents 1.0 General Precautions 2.0 Important Notice/Warranty 3.0 Items Included In Kit 4.0 Power Commander Tuning Tips 5.0 Wiring Diagrams 6.0 Optional Products 1.0-General Precautions This dry nitrous system is intended for Fuel Injected Motorcycles only! It should only be installed by a competent technician with nitrous experience. This is FOR RACE USE ONLY and is not intended for public roads or highways. All wiring and nitrous line should be wrapped with the provided wire loom and positioned in a way to prevent engine heat from doing any damage. The use of electrical tape at the end of the wire loom adds to the effect of "stock appearing." We also suggest running all the wiring and nitrous line alongside stock wiring. Be sure all wire terminals are water tight to prevent corrosion. The water proof arming switch should also be located in a discreet location to prevent detection. The nitrous bottle should be mounted away from any engine heat. Under the seat is a good location. Schnitz Racing offer nitrous bottle mounting brackets for some models. Be sure the siphon tube in the nitrous tank is pointing down. You may have to take the bottle valve off and readjust the siphon tube. The nitrous nozzle should mount in a ram air tube or at the very front of the air box. This is to assure equal distribution to all cylinder. The Nitrous will pass through the Air Filter. Start with the smallest supplied jet. Try it on the Dyno first, then try it on the race track. Use stock ignition timing only when you are using the nitrous. Advancing the timing can cause engine damage. Using a minimum 90 octane gasoline is highly recommended. It is recommended that you increase fuel with your Power Commander Map at 100% throttle. This is to insure enough fuel will get to the engine. Refer to your Power Commander manual for instructions on how to do this. We have included a recommended guideline for fuel increase at the end of this manual. Do not allow the engine to hit the rev limiter while using the nitrous. A RPM Activated Switch can be installed to turn off the Nitrous before the Rev Limiter RPM has been reached. Schnitz Racing recommends the TPRS-002. Contact Schnitz Racing at SchnitzRacing.com for more information. 1

2 2.0-Important Notice 1. Disclaimer of Warranties. SCHNITZ MOTORSPORTS, INC. MAKES NO WARRANTY OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT, WHETHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. YOU AGREE AND ACKNOWLEDGE THAT THIS PRODUCT IS SOLD ON AN "AS IS" AND "WITH ALL FAULTS" BASIS. YOU AGREE AND ACKNOWLEDGE THAT THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THIS PRODUCT SHALL BE BORNE BY YOU. IF THIS PRODUCT PROVES DEFECTIVE AFTER PURCHASE, YOU, AND NOT SCHNITZ MOTORSPORTS, INC., NOR ANY DISTRIBUTOR OR RETAILER, ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING AND/OR REPAIRS. 2. Use of Product at Purchaser's Own Risk. You agree and acknowledge that the use, installation, and/or operation of this product shall be at your own risk and may result in severe injury, death, and/or damage to person or property. 3. Limitation of Liability. TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW, YOU AGREE AND ACKNOWLEDGE THAT SCHNITZ MOTORSPORTS, INC., SHALL NOT BE LIABLE FOR ANY INJURY OR DAMAGE TO PERSONS OR PROPERTY, OR FOR ANY LOSS OF TIME, INCONVENIENCE, OR LOSS OF USE, INCLUDING ANY CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES ARISING DIRECTLY OR INDIRECTLY OUT OF OR IN CONNECTION WITH THIS PRODUCT'S USE, INSTALLATION, AND/OR PERFORMANCE, WHETHER SUFFERED BY THE PURCHASER OR ANY OTHER PARTY, AND REGARDLESS OF THE LEGAL THEORY UPON WHICH THE CLAIM IS BASED, EVEN IF SCHNITZ MOTORSPORTS, INC. HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. WITHOUT OTHERWISE LIMITING THE FOREGOING, IN NO EVENT SHALL RECOVERY OF ANY KIND AGAINST SCHNITZ MOTORSPORTS, INC. BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THIS PRODUCT. 4. Miscellaneous. This Disclaimer of Warranties ("Disclaimer") represents the complete and exclusive agreement between You and Schnitz Motorsports, Inc., and supersedes any prior agreements and/or communications regarding the subject matter hereof. The terms of this Disclaimer shall be governed by and construed in accordance with the laws of the State of Indiana, without regard to any conflict of law principle that would result in the laws of any other jurisdiction governing this Disclaimer. Any action or proceeding arising out of this Disclaimer shall be litigated in courts located in Adams County, Indiana. You consent and submit to the jurisdiction of any local, state, or federal court located in Adams County, Indiana. Any cause of action or claim you may have with respect to this product, whether in contract, tort, otherwise, must be commenced within one (1) year after the claim or cause of action arises, or such claim or cause of action is barred. If any term or provision contained in this Disclaimer is determined to be unenforceable in any respect, the enforceability of the term or provision in any other respect, and of the remaining terms or provisions of this Disclaimer, shall not be impaired. 2

3 3.0-Items Included In Kit Qty Description Line 1 Nitrous Solenoid 1 Fitting -4 Male to 1/8 Pipe 1 Fitting 3 Male to 1/8 Pipe 1 Modified Turbo Nozzle 1 Nozzle Tap, 1/16 Pipe Thread 1 #28 Jet 1 #34 Jet 1 #36 Jet 12 1/4 Loom, Black, For Wires and to hold Nitrous Line 1 6 Pole Water Proof Switch 8 Black Wire 8 Red Wire 20 Small Zip Ties 10 Large Zip Ties Stainless Line with 3 Hose Ends 1 Pack Misc. Electrical Terminals 4.0-Power Commander Tuning Tips For safe use of the nitrous system, more fuel will need to be delivered to the engine using the Power Commander. We recommend editing your existing map in the 100% throttle column and at the upper RPM range. Below is a chart with guideline for you to use at your discretion. 3 Nitrous Jet Schnitz Racing Dry Nitrous Jetting and Recommendation Chart For Fuel Injected 4 Cylinder Motorcycles (one injector per cylinder) with Single Nitrous Jet. Horsepower gain 600cc 750cc 1000cc 1300+cc Fuel % increase 14 6hp Stock Stock Stock Stock 3% 16 9hp Stock Stock Stock Stock 3% 18 12hp Stock Stock Stock Stock 5% 20 15hp Stock Stock Stock Stock 5% 22 17hp Stock Stock Stock Stock 8% 24 20hp Stock Stock Stock Stock 8% 26 25hp Stock Stock Stock Stock 10% 28 30hp Stock Stock Stock Stock 10% 30 34hp Mod Mod Stock Stock 12% 32 38hp Mod Mod Mod Stock 12% 34 40hp Mod Mod Mod Stock 15% 36 45hp Mod Mod Mod Stock 15% 38 50hp Mod Mod Mod Stock 17% 40 55hp Mod Mod Mod Mod 20% 42 65hp Mod Mo d Mod Mod 22% Stock - 93 Pump Gas, Stock Engine, Stock Timing Mod - Engine Modifications Recommended (Pistons, Rods, Valves, Valve Springs)

4 Below is a screenshot of the Power Commander software. Here, we added 10% more fuel from 8,000 RPM and higher in the 100% throttle column. Refer to your Power Commander Manual or Dynojet for details on how to do this. Note: If your motorcycle has 8 injectors (2 per cylinder), you will need to increase fuel by 3 times that of the chart provided on page 3. Example: 1000cc engine with 30 jet. Chart for 1 injector per cylinder shows to add 12% more fuel. For an engine with 2 injectors per cylinder, 36% more fuel should be added. This is just a guide. Dyno tuning is the best way to ensure a safe fuel curve. 4

5 5.0-Wiring Diagrams Some models provide +12V when the Horn Button is Activated. When using wiring diagram #2 the solenoid wire polarity will need to be reversed if the horn button provides +12V. Wiring Diagram #1 Wiring Diagram #2 5

6 Wiring Diagram #3, Starter Button Activation Below is a dyno graph of this dry nitrous system on a Suzuki Hayabusa. 6

7 6.0-Optional Products RPM Window Switch with Throttle Position Input The TPRS-002 RPM Window Switch provides a +12 volt output that is controlled by RPM and/or a Throttle Position Sensor signal (0 to 5 volt). The Throttle Position Input function can be turned OFF to provide a PRM Window Switch Controlled output. The RPM function can also be turned OFF to provide a Throttle Position Switch controlled output. Or, both control functions can be used together to control the +12 volt output based on Engine RPM and Throttle Position. This switch is a great way to control when your nitrous is activated. Check out SchnitzRacing.com for more info. The DCS-101 Nitrous Power controller is now being offered by Schnitz Electronics Inc. The new basic nitrous controller was designed for a simple and cost effective means to deliver nitrous power. A simple user interface and simplified wiring installation help to make the controller very user friendly. The starting power percentage can be adjusted from 20% to 50% in 2% increments. While the nitrous power build time is adjustable from 0.0 seconds(instant full nitrous power) to 8.0 seconds in 0.5 second increments. High amperage output drivers enable use with all popular solenoids. Overall size 4-3/8" long x 3" tall. 7