24 MULTI-POINT LOCKING SYSTEM CASEMENT

Transcription

1 SEMENT 4 MULTI-POINT LOKING SYSTEM STYLISH & EFFIIENT With its sleek, low-profile design, homeowners will love the fact that in either the locked or unlocked position it doesn t interfere with curtains or blinds. With its attractive painted finish, the locks all-metal handle & base precisely match the color of your vinyl profile. Homeowners will appreciate the extended reach-out capability. Instead of having to fully close the window before locking it, all you do now is close the window to within.65 (5.8 mm) and turn the one lock. ESE OF INSTLLTION Truth s locking system for vinyl casement windows is now easier to install then ever before. With less parts than comparable models, Truth s #4.84 Locking System is designed with parts that actually align themselves! The self-locating snap-on tie bar guides have feet protruding from within, that automatically index the tie bar the correct distance away from the frame, for precise installation everytime! The keepers too, have these unique feet designed into their construction to insure accurate hardware placement. ontact Truth for the guides and keepers specially created for your profile. nd even the tie bar itself, which has been designed so it will connect directly to the lock without the need for any additional screws, has been created with the manufacturer in mind. ELYE LOKING OPERTION The heart of this system is the progressive locking action. The first half of the handle s rotation fully engages the keeper closest to the bottom of the window, near the operator. The second half of the handle s rotation then engages and pulls-in the keeper at the top of the sash. Thus, you have Truth s patented positive sequential locking of the window. WETHER-TIGHT special O-ring around the base is an added feature Truth has included to ensure that the assembly is completely sealed against the leakage of air, water, or light. WRRNTY: Protected under the terms of the Truth Warranty for Window and oor Manufacturers and uthorized istributors. Refer to Truth s Terms and onditions for further details. MTERIL: High pressure zinc diecast handle and case. Steel tie bar. Keepers made of either steel or UV stabilized acetal. E-GR HRWRE Truth s E-Gard has a multi-stage coating process that produces a superior physical and aesthetic finish. Plus, it is resistant to a wider range of corrosive materials, including industrial cleaning materials and environmental pollutants. This proprietary process has been tested to be approximately three times better than common zinc plated finishes. FINISH: Electrostatically applied, durable coatings that provide excellent resistance to chipping, scratching and corrosion while maintaining color stability for years in direct sunlight. Please refer to Truth's olor hart for examples of Truth's most popular finish options. Truth also offers a wide range of decorative "plated" finishes - contact Truth for additional information on availability of these finishes on specific product lines. ORERING INFORMTION: ontact Truth for an application drawing providing complete details on your specific window profiles.. Order part #4.84. Specify finish number.. Specify left or right hand (determined by the hinge side when viewed from the outside). 4. Order keepers by part number - refer to chart. Handed the same as the lock. 5. Specify tie bar needed by length - refer to chart. 6. Specify Tie ar Guides by number - refer to chart. REOMMENE SREWS: Types of screws required determined by material of profile used. See Tech Note #. Refer to drawings for complete information on screw type and quantity needed (sold separately). 9

2 4 MULTI-POINT LOKING SYSTEM TRUTH TIPS:. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended.. For vinyl window applications, mounting screws should pass through two PV walls, or one PV wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended.. For metal window profiles, Truth recommends machine screws. However, in most applications, sheet metal screws will provide adequate holding power. 4. Truth recommends that a Snubber be used at the center of the hinge side on any casement window which has a tendency to bow outwardly at the center in the closed position. dding a Snubber may increase the negative air pressure rating of the window. INLUE TRUTH SPES ON YOUR NEXT WINOW PROJET Window locking system shall be included which will increase both security and weather seal tightness. The locking points must hold securely for negative air pressure and forced entry resistance. Window sash locks will be used which provides sequential locking with up to.65 (5.9 mm) of pull-in. The lock must utilize a tie bar driven by a single locking handle to meet hardware height standards. The lock drive handle must provide a weather tight seal by providing a O-ring between lock and window frame. The lock shall be constructed of high pressure zinc alloy die castings and E-Gard internal components. Window locks shall be 4 series, Multi-Point as manufactured by Truth Hardware, Owatonna, MN. 9a

3 4 MULTI-POINT LOKING SYSTEM FIG. PPLITION WITH THREE LOKING POINTS OVE MSTER LOK SHOWING INTERLOK ROLLER SYSTEM X.800 (0.mm) 6X #8 PH SST SHEET METL SREW X R.H. KEEPER (SEE FIG. 0) TIE R SSEMLY (SEE HRT ON FIG. 5) X TIE R GUIE (SEE FIG. ) 6X #8 PH SST SHEET METL SREW X.50 (9.mm).645 (6.4mm).85 (0.mm) SETION -.50 (8.9mm) REOMMENE X SUPPORT PLTE.595 (5.mm) SSH SHOWN ROTTE 80 FOR LRITY X 9545 SREW.770 (95.8mm) FRME FRME PRT NO XX SEE HRT ESRIPTION (RIGHT HN SHOWN) LOK SSEMLY (L.H XX.00) SUPPORT PLTE #8- PHILLIPS SELF THREING SREW TIE R GUIE (NON HNE) #8 PH SST SHEET METL SREW R GUIE KEEPER R.H. (L.H. IS ) #8 PH SST SHEET METL SREW (KEEPER) TIE R SSEMLY (NON HNE) EPENENT ON PROFILE ESIGN SREWS NOT FURNISHE Y TRUTH OTHER LENGTHS VILLE UPON REQUEST XX PINT OLOR OE 4.84.XX.0 MULTI-POINT LOK NOTE: 4. 4X R.56 UTOUT FOR LOK HOUSING MOUNTING SREWS FOR KEEPER N TIE R GUIE MUST PSS THRU TWO WLLS. IMENSION VRILE-EPENENT ON USTOMER PROFILES. WSHERS OR TRUTH PRT NO. 49 MY LSO E USE. (SEE FIG. 7) IMENSIONS,, & FOUN ON TIE R HRT (SEE FIG. 5) 9b

4 4 MULTI-POINT LOKING SYSTEM FIG. PPLITION WITH THREE LOKING POINTS OVE MSTER LOK SHOWING ONE ROLLER SYSTEM TIE R SSEMLY (SEE HRT ON FIG. 6) X X 8 R.H. KEEPER (SEE FIG. 9).48 (.mm) 6X #8 PH SST SHEET METL SREW 6X #8 PH SST SHEET METL SREWS X TIE R GUIE (SEE FIG. ) X.50 (9.mm).76 (5.0mm).45 (4.mm).50 (8.9mm) REOMMENE SETION - X SUPPORT PLTE.595 (5.mm) X 9545 SREW.770 (95.8mm) SSH SHOWN ROTTE 80 FOR LRITY FRME FRME PRT NO. ESRIPTION (RIGHT HN SHOWN) 4.84.XX.0 MULTI-POINT LOK 4X R.56 9c 4.84.XX SEE HRT LOK SSEMLY (L.H XX.00) SUPPORT PLTE #8- PHILLIPS SELF THREING SREW TIE R GUIE (NON HNE) #8 PH SST SHEET METL SREW R GUIE KEEPER RH (LH IS 7) #8 PH SST SHEET METL SREW (KEEPER) TIE R SSEMLY (NON HNE) EPENENT ON PROFILE ESIGN SREWS NOT FURNISHE Y TRUTH OTHER LENGTHS VILLE UPON REQUEST XX PINT OLOR OE 4. UTOUT FOR LOK HOUSING MOUNTING SREWS FOR KEEPER N TIE R GUIE MUST PSS THRU TWO WLLS. IMENSION VRILE-EPENENT ON USTOMER PROFILES. WSHERS OR TRUTH PRT NO. 49 MY LSO E USE. (SEE FIG. 7) IMENSIONS,, & FOUN ON TIE R HRT. (SEE FIG. 6)

5 4 MULTI-POINT LOKING SYSTEM FIG. PPLITION WITH THREE LOKING POINTS OVE MSTER LOK X 0 R.H. KEEPER (SEE FIG.8) 6X #8 PH SST SHEET METL SREW TIE R SSEMLY (SEE HRT ON FIG. 5) X TIE R GUIE (SEE FIG. ) 6X #8 PH SST SHEET METL SREWS X.560 (9.6mm) X.50 (9.mm).85 (0.mm).645 (6.4mm).50 (8.9mm) REOMMENE SETION - X SUPPORT PLTE.595 (5.mm) PRT NO XX SEE HRT X 9545 SREW SSH SHOWN ROTTE 80 FOR LRITY ESRIPTION (RIGHT HN SHOWN) LOK SSEMLY (L.H XX.00) SUPPORT PLTE #8- PHILLIPS SELF THREING SREW TIE R GUIE (NON HNE) #8 PH SST SHEET METL SREW R GUIE KEEPER R.H. (L.H. IS 0) #8 PH SST SHEET METL SREW (KEEPER) TIE R SSEMLY (NON HNE) EPENENT ON PROFILE ESIGN SREWS NOT FURNISHE Y TRUTH OTHER LENGTHS VILLE UPON REQUEST XX PINT OLOR OE FRME NOTE: XX.0 MULTI-POINT LOK X.770 (95.76mm) FRME.56 X R UTOUT FOR LOK HOUSING MOUNTING SREWS FOR KEEPER N TIE R GUIE MUST PSS THRU TWO WLLS. IMENSION VRILE-EPENENT ON USTOMER PROFILES. WSHERS OR TRUTH PRT NO. 49 MY LSO E USE. (SEE FIG. 7) IMENSIONS,, & FOUN ON TIE R HRT. (SEE FIG. 5) 9d

6 4 MULTI-POINT LOKING SYSTEM FIG. 4 WNING PPLITION WITH ONE LOKING POINT ELOW MSTER LOK SHOWING INTERLOK ROLLER SYSTEM (available with cone roller system) 44 TIE R SSEMLY X TIE R GUIE (SEE FIG.) 4X #8 PH SST SHEET METL SREWS X.50 (9.mm).595 (5.mm) 8.0 (0.mm).700 (97.mm).770 (95.8mm) R.H. KEEPER (SEE FIG. 0) FRME.800 (0.mm) 4X R.56 E X #8 PH SST SHEET METL SREW 7.0 (77.8mm) UTOUT FOR LOK HOUSING SSH SHOWN ROTTE 80 FOR LRITY FRME PRT NO XX ESRIPTION (RIGHT HN SHOWN) LOK SSEMLY (L.H XX.00) SUPPORT PLTE #8- PHILLIPS SELF THREING SREW TIE R GUIE (NON HNE) #8 PH SST SHEET METL SREW R GUIE KEEPER R.H. (L.H. IS 0) #8 PH SST SHEET METL SREW (KEEPER) TIE R SSEMLY (NON HNE) NOTE: REFER TO SEMENT MULTI-POINT PPLITION RWING FOR REMINING IMENSIONS N ILL OF MTERILS. E IMENSIONS N VRY ORING TO THE PROFILE. IMENSIONS N E QUIRE FROM TRUTH. TIE R SSEMLIES TRUTH PRT N0. 0 (ONE ROLLER) OR PRT NO. 90 (INTERLOK ROLLER) MY E USE. EPENENT ON PROFILE ESIGN SREWS NOT FURNISHE Y TRUTH XX PINT OLOR OE 4 THIS SYSTEM WOUL E REPETE ON OTH JMS OF N WNING WINOW. 9e

7 4 MULTI-POINT LOKING SYSTEM FIG. 5 TIE R HRT FOR INTERLOK ROLLER.500 (.7mm) WINOW SIZE in (558.8mm) 6 in (660.4mm) 0 in (76.0mm) 4 in (86.6mm) 8 in (965.mm) 4 in (066.8mm) 46 in (68.4mm) 50 in (70.0mm) 54 in (7.6mm) 58 in (47.mm) 6 in (574.8mm) 66 in (676.4mm) 70 in (778.0mm) TIE R SSEMLY PRT NO. ROLLERS ROLLERS IM 900 N 0.9 (76.9mm) 90 N 4.9 (78.5mm) 90 N 8.9 (480.mm) (58.7mm) (68.mm) (784.9mm) (886.5mm) (988.mm) (089.7mm) (9.mm) (9.9mm) (94.5mm) (496.mm) IM 7.0 (77.8mm).0 (79.4mm) 5.0 (8.0mm) 9.0 (48.6mm).0 (584.mm) 7.0 (685.8mm).0 (787.4mm) 5.0 (889.0mm) 9.0 (990.6mm) 4.0 (09.mm) 47.0 (9.8mm) 5.0 (95.4mm) 55.0 (97.0mm) IM N N N 0.0 (54.0mm).0 (04.8mm) 4.0 (55.6mm) 6.0 (406.4mm) 8.0 (457.mm) 0.0 (508.0mm).0 (558.8mm) 4.0 (609.6mm) 6.0 (660.4mm) 8.0 (7.mm) FIG. 6 TIE R HRT FOR ONE ROLLER.500 (.7mm) WINOW SIZE in (558.8mm) 6 in (660.4mm) 0 in (76.0mm) 4 in (86.6mm) 8 in (965.mm) 4 in (066.8mm) 46 in (68.4mm) 50 in (70.0mm) 54 in (7.6mm) 58 in (47.mm) 6 in (574.8mm) 66 in (676.4mm) 70 in (778.0mm) PRT NO. ROLLERS ROLLERS N N N TIE R SSEMLY IM 0.9 (76.9mm) 4.9 (78.5mm) 8.9 (480.mm).9 (58.7mm) 6.9 (68.mm) 0.9 (784.9mm) 4.9 (886.5mm) 8.9 (988.mm) 4.9 (089.7mm) 46.9 (9.mm) 50.9 (9.9mm) 54.9 (94.5mm) 58.9 (496.mm) IM 7.0 (77.8mm).0 (79.4mm) 5.0 (8.0mm) 9.0 (48.6mm).0 (584.mm) 7.0 (685.8mm).0 (787.4mm) 5.0 (889.0mm) 9.0 (990.6mm) 4.0 (09.mm) 47.0 (9.8mm) 5.0 (95.4mm) 55.0 (97.0mm) IM N N N 0.0 (54.0mm).0 (04.8mm) 4.0 (55.6mm) 6.0 (406.4mm) 8.0 (457.mm) 0.0 (508.0mm).0 (558.8mm) 4.0 (609.6mm) 6.0 (660.4mm) 8.0 (7.mm) 9f

8 4 MULTI-POINT LOKING SYSTEM FIG. 7 SUPPORT PLTE & WSHERS.074 (.9mm) X.70 (4.mm) Ø.88 (4.8mm).660 (6.8mm).590 (5.0mm).95 (7.5mm) SUPPORT PLTE Ø.88 (4.8mm).080 (.0mm) (8.9mm) 4.5 (05.5mm).590 (5.0mm).78 (7.mm) Ø.500 (.7mm) FIG. 8 KEEPER 0 N 0 (for interlock roller system) 0 - RH 0 - LH.070 (.8mm) WSHER SHOWN.56 (9.7mm) Ø.65 (5.9mm) 4 WSHER.0 (8.0mm) FIG. 9 KEEPER 8 N 7 (for cone roller system) 8 - RH 7 - LH.464 (.8mm) SHOWN SUPPORT PLTE 49.7 (6.9mm).48 (.mm) REOMMENE SREWS:.90 (49.0mm).75 (60.mm) REOMMENE SREWS:.04 (7.7mm).778 (45.mm).89 (.7mm) WOO/PV/METL: - #8 PHILLIPS, PN HE, SST SREWS (LENGTH N THRE TYPE TO E ETERMINE Y PROFILE) FIG. 0 JUSTLE KEEPER (for interlock roller system).6 (9.mm).800 (0.mm).850 (47.0mm).65 (5.9mm).46 (6.mm) IMENSION WILL VRY TO SUIT USTOMER PROFILE REOMMENE SREWS: RIGHT HN SHOWN WOO/PV/METL: - #8 PHILLIPS, PN HE, SST SREWS (LENGTH N THRE TYPE TO E ETERMINE Y PROFILE).5 (8.mm) WOO/PV/METL: - #8 PHILLIPS, FLT HE, SST SREWS (LENGTH N THRE TYPE TO E ETERMINE Y PROFILE) FIG. JUSTLE TIE R GUIE NON HNE.50 (9.mm) (0.mm) (7.mm) &.75 (8.mm).6 (4.mm).750 (9.mm) IMENSIONS WILL VRY TO SUIT USTOMER PROFILE REOMMENE SREWS: WOO/PV/METL: - #8 PHILLIPS, PN HE, SST SREWS (LENGTH N THRE TYPE TO E ETERMINE Y PROFILE) 9g 700 WEST RIGE STREET, OWTONN, MN TRUTH.OM