Brief Description SOLIDO. Fully biological SBR Small Wastewater Treatment Plant for 2 32 PE according to EN

Transcription

1 Brief Description SOLIDO Fully biological SBR Small Wastewater Treatment Plant for 2 32 PE according to EN REWATEC GmbH Bei der neuen Münze Hamburg Germany Telephonic expertise: (9-16 h) info@rewatec.de web: DOKK5201E KB SOLIDO engl. Seite 1 von 12

2 1. Brief Description General SBR-small Wastewater Treatment Plant (KKA) SOLIDO consists of highly resistant polyethylene plastic containers and work with the Sequencing Batch Reactor Process. It is available in several versions for 2 40 inhabitants. Approvals General technical approval from the German Institute for Civil Engineering (DIBt) for the effluent classes C, N and D. Cleaning category SOLIDO conforms to the cleaning category C, N and D (Carbon and Nitrogen degradation as well as additional denitrification) and can keep the following requirements: BOD 5 : 20 mg/l from a grab sample, homogenised COD: 90 mg/l from a grab sample, homogenised NH 4 -N: 10 mg/l from a 24 h composite sample, filtrated N anorg : 25 mg/l from a 24 h composite sample, filtrated Manufacturing SOLIDO is manufactured as a one-container plant with a separating wall or as a morecontainer plant. The containers are industrially made of highly resistant polyethylene (LLD-PE) in the rotation sintering process. Manufacturing enterprise is the ROTA GmbH, Am Gammgraben 2, D Boizenburg. Warranty 25 years manufacturer s warranty for containers, 3 years manufacturer s warranty for electrical units such as aerator, pumps and control with the correct operation and maintenance by a service partner authorised by REWATEC.. Mode of operation SOLIDO always has at least two separated chambers. The first acts as a sludge reservoir and buffer, in the second chamber the cleaning process takes place. The SBRsystem SOLIDO provides the oxygen supply of the microorganisms via a compressor and pipe shaped aerator. These microorganisms transform the contents of the wastewater into settleable activated sludge. The emerging excess sludge is pumped into the first chamber, during the treatment. The treatment takes place in batches, each cycle lasts 6 hours and is controlled by a programmable electronic control unit. The control unit allows to adapt the running operation times when the local conditions vary. The patented construction of the air lifters enables the system to do an automatic backflush before every start. A sludge loss or blocking of the charging lifter are avoided. Energy consumption The SBR-system SOLIDO has a compressor with an electrical power from 46 to 210 Watt (depending on the size of the plant), three solenoid valves, one control unit, as well an optional float switch (SOLIDO Sensor). Because of the efficient utilisation of the compressed air the energy consumption according to the desired decomposition rate and actual utilization is about 50 kwh per inhabitant and year for the effluent class C. This average cost is 13,50 per person/ year (with an electricity tariff of 0.27 /kwh). DOKK5201E KB SOLIDO engl. Seite 2 von 12

3 Holiday mode The control offers the possibility to enter the length of a holiday / absence for up to 30 days (savings mode). At the end of the entered time the control automatically returns again to the standard mode. Energy saving mode (at version SOLIDO Sensor with float switch) If no wastewater inflow takes place for a longer period, the aeration time is reduced automatically. With this energy saving mode, the microorganisms are kept alive even during holidays, and at the same time energy is saved. Maintenance and Sampling According to German Institute for Civil Engineering (DIBt) approval the SOLIDO plant has to be maintained twice a year. Within the maintenance the time of the sludge removal from the first chamber is fixed. This has to be carried out every 6-24 month, depending on the utilisation and the type series. The sampling is carried out by removing the content of the sample bottle. It is changed during the clearwater removal every 6 hours, so that a current sample is available any time. Installation notes The containers have to be installed in a sharp object free, shock-free trench, whose base has to be well compressed and level. For the installation, half fill the containers with water, coat them with proper material from all sides, with a thickness of cm and compact it in layers. The filling material has to be well compressible, permeable, shearing resistant and free from sharp objects (e.g. gravel sand with wide staged granulation). Concrete is not necessary. The installation is possible in a depth of groundand surface water of 1.00 m under ground, when the necessary height above ground is considered. The SBR-aggregate SOLIDO has to be connected by a plug-in cable (15 m or 30 m length) to the plant control. A duct pipe (DN70 DN100) should be installed for this purpose. The control unit has to be plugged into a socket with a separately secured ground fault circuit interrupter (30mA), with a working PE-conductor. Further information for the installation can be found in the installation guidelines for MONOLITH containers I and II. There is also information about the installation of drivable versions resp. the installation at high ground water levels (buoyancy protection, welding of shaft elements, rubber seals, etc.). Operator s duties Among the general duty of care such as the avoidance of the discharge of inappropriate substances, like chemicals resp. contraries of all kinds, the operator has to make sure that the plant is operating correctly. Visual inspections have to be carried out monthly and have to be noted in the operations logbook. The operating times of the plant are automatically saved in the operations logbook of the control unit. A written logbook is recommended and required by the water authorities! Approval A precondition for the operation of a small Wastewater Treatment Plant is obtaining the correct approvals from your local water authority and an acceptance / startup by a specialised company. DOKK5201E KB SOLIDO engl. Seite 3 von 12

4 2. Product Qualities SOLIDO compact: minimum required space with only two chambers, without separate final sedimentation quiet: no noise inside the house because of integrated technical capsule easy to assemble: all hoses and small parts are pre-mounted in the MONOLITH container only one pre-finished pipe between tank and house, no installation of complicated hose packages necessary Fail-safe: extremely robust and guaranteed single, one-piece container (can be installed in heavy grounds and high ground water up to 1.00 m) plug-proof compressed air lifter air lifters with a patented automatic backflush prevent sludge loss and improve the effluent qualitiy reliable, multiple proved control unit with integrated operations logbook + holiday mode easy: economical: light, rectangular container for an easy installation and handling integrated sample bottle, no separate sampling chamber necessary low energy consumption of only about 50 kwh/ew*a because of efficient utilisation of compressed air and adapted aeration * Measuring results test field PIA, Aachen 2012 DOKK5201E KB SOLIDO engl. Seite 4 von 12

5 3. One container systems 3.1 Main dimensions MONOLITH II DOKK5201E KB SOLIDO engl. Seite 5 von 12

6 3.2 Shaft system for MONOLITH II Shaft Elements cone + VS 20 Application area Walk-on version (standard scope of delivery) cone + spacer ring + VS 20 higher installation depth cone + VS 60 / BS 60 Car driveable (BS60) resp. with higher installation depth (VS60) cone + spacer ring Preparation lorry driveability spacer ring cone + VS 20 Spacious shaft element, higher installation depth NOTES: MONOLITH II containers have a inspection shaft DN and a shaft DN 200 for desludging, that is scope of delivery with a height of 620 mm. Extensions DN 200 or drivable covers must be applied onsite. The inspection shaft plants can be shortened in the standard version up to 12 PE to about max. 14 cm! With lower installation depths an alternative siting of the technical capsule can be achieved e.g. in a separate capsule shaft. All given measurements with range of variation show the possible installation depth given by telescopic pushing of the respective shaft elements. spacer ring cone + VS 60 / BS 60 Spacious shaft element, higher installation depth 3.3 SOLIDO 5 E-35-II as walk-on standard version with cone and VS20 DOKK5201E KB SOLIDO engl. Seite 6 von 12

7 3.4 SOLIDO for deeper installation (cone + spacer ring VS 20) 3.5 SOLIDO 5 E-35-II for deeper installation depth resp. car driveable with cone and BS60 (isometric to VS60) ** A shaft DN 200 with a height of 620 mm is within the scope of delivery, extensions for that as well as drivable covers have to provided by the customer. DOKK5201E KB SOLIDO engl. Seite 7 von 12

8 3.6 SOLIDO as version with wider shaft elements with spacer ring DN 800, cone and VS SOLIDO 5 E-35-II as lorry drivable version with cone and spacer ring (Drivable >3,5to <12to, more than 12to by request) * Adjustable by shortening the spacer ring ** A shaft DN 200 with a height of 620 mm is within the scope of delivery, extensions for that as well as drivable covers have to provided by the customer. DOKK5201E KB SOLIDO engl. Seite 8 von 12

9 4. Multiple container plants 4.1 SOLIDO standard two-container plants in MONOLITH II Example SOLIDO 16 E-60/60 Measures two container plant SOLIDO (standard version in MONOLITH II) Name Order No. Length Width Height (incl. shaft) Weight SOLIDO 10 E-35/ PE SOLIDO 12 E-45/ PE SOLIDO 16 E PE KBMS x 240 cm 124 cm 220 cm 2 x 200 kg KBMS x 307 cm 122 cm 220 cm 2 x 240 kg KBMS x 340 cm 122 cm 249 cm 2 x 340 kg DOKK5201E KB SOLIDO engl. Seite 9 von 12

10 4.2 SOLIDO multiple container plant in MONOLITH II (without drawing) Measures multiple container plant SOLIDO (standard version in MONOLITH II) Name Order No. Length Width Height (incl. shaft) Weight SOLIDO 18 E-45+45/ PE SOLIDO 24 E-60+60/ PE SOLIDO 32 E-60+60/ PE KBMS x 307 cm 122 cm 220 cm 3 x 240 kg KBMS x 340 cm 122 cm 249 cm 3 x 340 kg KBMS x 340 cm 122 cm 249 cm 4 x 340 kg 4.3 SOLIDO Plus two container plant in MONOLITH I (with big sludge reservoir) Inlet Pretreatment/Buffer Outlet Measures two container plant SOLIDO Plus with big sludge reservoir in MONOLITH I Name Order No. Length L1 + L2 Width Height (incl. shaft) Weight SOLIDOPlus 30/15 KBMS cm +128 cm 120 cm cm 200 kg kg SOLIDOPlus 35/20 KBMS cm +160 cm 120 cm cm 220 kg kg SOLIDOPlus 50/30 KBMS cm +208 cm 120 cm cm 280 kg kg DOKK5201E KB SOLIDO engl. Seite 10 von 12

11 4.4 SOLIDO BlackLine multiple container plant (without drawing) Measures multiple container plant SOLIDO BlackLine Name Order No. Length L1 + L2 Width Height (incl. shaft) Weight BlackLine 20 E-75/ PE BlackLine 26 E-90/ PE BlackLine 28 E-75+75/ PE BlackLine 36 E-90+90/ PE BlackLine 42 E-75+75/ PE BlackLine 50 E-90+90/ PE KBMS x 246 cm 208 cm 290 cm 2 x 280 kg KBMS x 344 cm 206 cm 290 cm 2 x 370 kg KBMS x 246 cm 208 cm 290 cm 3 x 280 kg KBMS x 344 cm 206 cm 290 cm 3 x 370 kg KBMS x 246 cm 208 cm 290 cm 4 x 280 kg KBMS x 344 cm 206 cm 290 cm 4 x 370 kg DOKK5201E KB SOLIDO engl. Seite 11 von 12

12 5. Performance results corresponding to EN REWATEC GmbH May 2013 We reserve the right of technical modifications. No responsibility for printing mistakes will be accepted. The contents of the installation and commissioning are part of the guarantee requirements. DOKK5201E KB SOLIDO engl. Seite 12 von 12