MODELS S4LX, S4BX, S4KX, S4QX, H4QX, S4LVX, S6AX, S6LX and S8FX

Transcription

1 SLX MODELS SLX, SBX, SKX, SQX, HQX, SLVX, SAX, SLX and SFX (Class I, Division, Groups C & D): FM HAZARDOUS LOCATION SUBMERSIBLE PUMP INSTALLATION AND SERVICE MANUAL NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system. SLX SFX Item # E-0- Part # -- 0 Pentair Pump Group, Inc. //

2 Thank you for purchasing your Hydromatic pump. To help ensure years of trouble-free op er a tion, please read the following manual carefully. Before Operation: Read the following in structions care ful ly. Reasonable care and safe meth ods should be practiced. Check local codes and requirements before installation. Attention: This manual contains important information for the safe use of this product. Read this manual completely before using this product and refer to it often for con tin ued safe product use. DO NOT THROW AWAY OR LOSE THIS MANUAL. Keep it in a safe place so that you may refer to it often. Unpacking Pump: Remove pump from carton. When un pack ing unit, check for con cealed damage. Claims for damage must be made at the receiving end through the delivery carrier. Dam age cannot be processed from the factory. WARNING: Before handling these pumps and controls, always disconnect the power first. Do not smoke or use sparkable electrical devices or flames in a septic (gaseous) or possible septic sump. General Information CALIFORNIA PROPOSITION WARNING: This product and related accessories contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Pumps in Storage or Not Operating: Pumps with carbon ceramic seals must have impellers manually rotated ( revolutions) after setting non-operational for months or longer and prior to electrical start-up. Pumps with tungsten carbide seals must have impellers manually rotated ( revolutions) after setting non-operational for weeks or longer and prior to electrical start-up. Seal Failure Probes: All hazardous location submersible pumps have two factory installed mois ture detectors (seal failure probes). They are in a normally open series cir cuit, in the seal chamber. Un der normal operating conditions, the circuit remains open. If the lower seal leaks and moisture enters this cham ber, the moisture would settle to the bottom of the chamber and will com plete the circuit between the moisture detectors. This circuit must be connected to a sensing unit and signaling device. This is supplied in a Hydromatic built control panel. NOTE: Failure to install such a device negates all war ran ties by Hydromatic. Heat Sensors: All motors in this family have heat sensors on or embedded in the motor winding to detect ex ces sive heat. This prevents damage to the motor. If sen sor trips due to excessive winding tem per a ture, starter in panel breaks power to the pump. Once sensor re sets, the starter is automatically reset for FM for continued operation of the pump. This circuitry is supplied in a Hydromatic control panel. NOTE: Failure to install such circuitry negates FM ap prov als and all warranties by Hydromatic. Power Cords: The power cord and heat sensor seal failure cord are potted into the con nec tion box cap. The cords must not be spliced. NOTE: Each cable has a green lead. This is the ground wire and must be grounded properly per NEC and/or local codes. Cords should be in spect ed for abnormal wear and replaced accordingly. Overload Heaters: If the Hydromatic electrical panel is not used, start ers with leg overload relay must be supplied on phase pumps. Each leg is to have an iden ti cal heater sized in accordance with the nameplate amps on the motor hous ing. The amp draws on these sub mers ible motors is slightly higher than a cor re spond ing horsepower sur face motor, so heat ers must be sized by the nameplate rating.

3 Pump Installation Installing Sump Level Control Float Controls: In either simplex, duplex or triplex systems the lower or turn-off control is to be set to Installing Sump Level Control Float Controls: In either simplex, duplex or triplex systems the lower or turn-off control is to be set to maintain a minimum level in the sump. This level shall be no more than " from the top of the motor housing down to the surface of the sewage. The second or turn-on control is set above the lower turn-off control. The exact distance between the two floats must be a compromise between a fre quent pumping cycle ( starts per hour max.) to control septicity, solids and a slower cycle for energy econ o my. This distance should be de ter mined by the engineer or consulting engineer depending on the con di tions of the application. For installation of Hydromatic supplied level con trols refer to your sys tem s installation and service manual. Installing Pump in Sump: Before installing pump in sump lay it on side and rotate impeller. Impeller may be slightly stuck due to factory test water so it must be broken loose with small bar or screwdriver in edge of vanes. The impeller should turn freely. Do not connect the power until after this test. Clean all trash and sticks from sump and connect pump to piping. A check valve must be installed on each pump. A gate or plug valve in each pump discharge is highly rec om mend ed. This valve should be installed on the discharge side of the check valve so if necessary to service the check valve the line pressure can be cut off. Sin gle pump systems are sometimes installed without a check valve where it is de sir able to self-drain the dis charge line to prevent freezing. This can be done only with short discharge lines; oth er wise water will return to the sump and cause short cycling of the pump. Making Electrical Connections: All electrical wiring must be in ac cor dance with local code, and only qual i fied electricians should make the in stal la tions. All wires should be checked for shorts to ground with an ohmmeter or Megger after the con nec tions are made. This is important, as one grounded wire can cause considerable trouble. IMPORTANT: If equipment is not properly wired and protected as recommended, Hydromatic warran ty is void. Heat Sensor and Seal Failure Connections: If a Hydromatic control panel is used, terminal blocks are provided for heat sensor, seal failure connections. If a control panel is supplied by others, it must allow heat sensor and seal failure terminations. Pump Operations Starting System:. Double check all wire connections.. Turn pumps to Off position on H-O-A switch es.. Turn on breakers.. Turn H-O-A switch to Hand po si tion on one pump and notice oper ation. If pump is noisy and vibrates, rotation is wrong. To change ro ta tion, interchange any two line leads to pump. Do not in terchange main incoming lines. Check ro ta tion of all pumps in this same man ner.. Now set both H-O-A switches to Auto po si tion and allow water to rise in sump until one pump starts. Allow pump to operate until the level drops to turn-off point.. Allow sump level to rise to start other pump(s). Notice run lights to panel. Pumps should alternate on each successive cycle of operation.. Turn both H-O-A switches to Off position and allow sump to fill to the override control level(s).. Turn switches to Auto position, and pumps should start and op er ate together until level drops to turn-off point.. Repeat this operation cycle sev er al times before leaving the job.

4 . Check voltage when pumps are operating, and check the amp draw of each pump. Check amps on each wire as sometimes a high leg will exist. One leg can be some what higher by to per cent without causing trouble. For excessive amp draw on one leg, the electric utility company should be consulted. Pump Maintenance As the motors are oil filled, no lubrication or other main te nance is required. If the heat sensor and seal failure are hooked up properly, no attention is necessary as long as the seal failure indicator light doesn t come on. To ensure continuity of the seal sensor leads, a test light is provided on in trin si cal ly safe Hydromatic panels as standard equipment. Pump should be checked every quar ter for cor ro sion and wear. Field Service on Hydromatic Hazardous Location Pumps: If a Hydromatic hazardous location pump is used in a hazardous location, or if the pump is still in war ran ty, the pump must be returned to the factory for service or repaired at an authorized Hydromatic service center. Charges will not be allowed if in war ran ty pump is not taken to an authorized Hydromatic service cen ter. This will ensure the integrity of the hazardous location rating of the pump and com ply with our warranty requirements. Disconnecting Pump Cords: If a Hydromatic hazardous location pump is to be removed from its lo ca tion, the pump cords may be disconnected at control panel (on sump mounted con trol panels) and cord as sem bly taken with pump. CAUTION: If cord openings from sump to con trol panel are open, gas es from sump could enter panel and an explosive condition could ex ist. CAUTION: Do not reconnect pow er to a cord and cap assembly while removing from pump. Replacing Cords: The power cord and heat sensor - seal failure cord is potted into the con nec tion box cap, forming the cord and cap assembly. If cords require replacement due to damage or cords being too short, cord and cap assembly must be replaced as a complete assembly avail able from factory. Check pump for proper rotation before re turn ing to normal service. Replacing Lower Seal, Impeller or Volute: The wet end components may be repaired or replaced by an authorized Hydromatic service facility without compromising the hazardous location rating to the pump. NOTE: Any time the seal is disturbed, it must be replaced.

5 SLX Parts List RTF Cord Cap Assy Connector -/- HP 00//0 RPM -/- HP 0/0//0 RPM -/- HP //0 RPM - HP 00//0 RPM - HP 0/0//0 RPM - HP //0 RPM HP 0//0 RPM -0 HP 0//0 RPM -/- HP 00//0 RPM -/- HP 0/0//0 RPM -0 HP //0 RPM Connector -0 HP 0//0 RPM Connector -0 HP 00//0 RPM -0 HP 0/0//0 RPM -0 HP 0//0 RPM 0 HP 0//0 RPM Connector 0 HP 0//0 RPM Connector -/- HP 0//0 RPM - HP 0//0 RPM Connector -/- HP 0//0 RPM - HP 0//0 RPM Connector HP 0//0 RPM -0 HP 0//0 RPM O-Ring SC Connector Connector -/- HP 00//0 RPM -/- HP //0 RPM - HP 00//0 RPM - HP //0 RPM -/- HP 0/0//0 RPM - HP 0/0//0 RPM Connector -0 HP 00//0 RPM -0 HP 0//0 RPM Connector -0 HP 0/0//0 RPM Connector -0 HP 0//0 RPM Connector - HP 00//0 RPM -/- HP 00//0 RPM HP //0 RPM -0 HP //0 RPM -0 HP 0/0//0 RPM Key Stator Holding Ring Lower Bearing O-Ring SC Seal Sensor Assy Seal Failure Terminal Pipe Plug Key O-Ring Capscrew Roll Pin Seal Plate 0-0- Impeller." dia 0-0- Impeller." dia Impeller.00" dia Impeller." dia Impeller.0" dia 0-0- Impeller." dia 0-0- Impeller.00" dia 0-0- Impeller." dia Impeller.0" dia 0-0- Impeller.00" dia Impeller." dia 0-0- Impeller." dia Impeller." dia O-Ring SC Impeller Washer Capscrew Wearing Ring Lower Seal, Ceramic (std) S Lower Seal, Carbide (opt) C Volute Capscrew Retaining Ring Bearing Housing Upper Seal SC Capscrew Shaft Sleeve SC Capscrew RTF Stator RTF Rotor & Shaft Motor Housing HP 0 RPM, -0 HP 0 RPM -00- Motor Housing -/- HP 0 RPM, - HP 0 RPM Screen Fill Oil to above the Top of Motor Windings, Spacer -/- HP 0 RPM Spacer -0 HP 0 RPM Spacer -- HP 0 RPM 0A0 Upper Bearing Load Spring Jam Nut Eye Bolt Connection Box #- -/- HP 00//0 RPM -/- HP //0 RPM -/- HP 00//0 RPM -/- HP //0 RPM -0 HP //0 RPM Connection Box #- -/- HP 0/0//0 RPM - HP 0/0//0 RPM Connection Box #- -0 HP 00//0 RPM -0 HP 0//0 RPM Connection Box #- -0 HP 0/0//0 RPM Connection Box #- -0 HP 0//0 RPM O-Ring SC Capscrew SST Capscrew SST Setscrew Labyrinth Ring Seal Kit 00-- Carbide Seal Kit 0 0

6 SFX Parts List RTF Cord Assy, Dual Connector HP 00/0/0///0 RPM HP 0/0///0 RPM 0 HP 0/0//0 RPM -/ HP 00/0/0//0 RPM 0 HP // Connector HP 00/0/0//0 RPM -0 HP 0//0 RPM Connector 0 HP 00/0/0//0 RPM 0 HP 0//0 RPM 0 HP 0//0 RPM Connector 0 HP 0//0 RPM Connector HP 0//0 RPM HP 0//0 RPM Connector -/ HP 0//0 RPM HP 0//0 RPM Connector HP 0//0 RPM 0 HP 0//0 RPM O-Ring SC Connector Connector HP //0 RPM HP 00//0 RPM HP //0 RPM HP 0/0//0 RPM HP 0/0//0 RPM Connector 0 HP 00//0 RPM 0 HP 0//0 RPM 0 HP //0 Connector 0 HP 0/0//0 RPM Connector 0 HP 0//0 RPM Connector HP 00//0 RPM -/ HP 00//0 RPM HP //0 RPM 0 HP //0 RPM Connector 0 HP 0//0 RPM Key Stator Holding Ring Lower Bearing O-Ring SC Seal Sensor Assy Seal Failure Terminal Pipe Plug Safety Wire O-Ring SC Capscrew Key Seal Plate 0-0- Impeller." Impeller." Impeller.0" Impeller." 0-0- Impeller." Impeller." 0-0- Impeller." Impeller.0" 0-0- Impeller." Impeller.", Impeller.0" Roll Pin Impeller Washer Capscrew Wearing Ring Lower Seal (Std.) S Lower Seal (Carbide) C Volute w/ring 0A0 Capscrew Retaining Ring Bearing Housing Upper Seal SC Capscrew Shaft Sleeve SC Capscrew RTF Stator RTF Rotor & Shaft Motor Housing HP 0 RPM 0 HP 0 RPM -00- HP 0 RPM HP 0 RPM 0A00 O-Ring SC Spacer HP 0 RPM HP 0 RPM HP 0 RPM 0A0 Upper Bearing Bearing Adj. Spring 0 DUAL VOLTAGE PHASE MOTOR WIRING 0V ø 0V ø BL W R (L) (L) (L) BL W R (L) (L) (L) Nut Bolt Connection Box #- HP 00//0 RPM HP //0 RPM HP 00//0 RPM HP //0 RPM 0 HP //0 RPM Connection Box #- - HP 0/0//0 RPM - HP 0/0//0 RPM Connection Box #- 0 HP 00//0 RPM 0 HP 0//0 RPM Connection Box #- 0 HP 0/0//0 RPM Connection Box #- 0 HP 0//0 RPM O-Ring SC A0 Capscrew, SS A0 Capscrew, SS Screen Setscrew Labryrinth Ring Seal Kit 00-- Carbide Seal Kit Fill Oil to above the Top of the Motor Windings

7 SBX Parts List RTF Cord Cap Assy Connector & HP 00, 0/0, //0 RPM Connector & HP 0/0//0 RPM Connector. & HP 00//0 RPM Connector,.,, HP 00 & //0 RPM Connector HP 00, 0/0//0 RPM Connector,., HP 0/0//0 RPM Connector, HP 0/0//0 RPM Connector 0 HP 00, 0/0//0 RPM Connector -0 HP 0 & 0//0 RPM Connector -0 HP 0 & //0 RPM Connector 0,, 0 HP //0 RPM Connector 0 HP 0//0 RPM Connector 0 HP 0/0//0 RPM O-Ring SC Connector Connector,., HP //0 RPM HP 00//0 RPM & HP //0 RPM Connector,., HP 0/0//0 RPM & HP 0/0//0 RPM Connector 0 HP 00//0 RPM 0, 0, 0 HP 0//0 RPM 0 & 0 HP //0 RPM Connector 0 HP 0/0//0 RPM Connector & 0 HP 00//0 RPM 0 & 0 HP 0//0 RPM HP 0//0 RPM Connector HP 0//0 RPM Connector 0,, 0 HP //0 RPM HP //0 RPM. & HP 00//0 RPM & HP 00//0 RPM -0 HP 0//0 RPM Connector -0 HP 0//0 RPM O-Ring SC Stator Holding Ring Lower Bearing O-Ring SC Seal Sensor Assy Seal Failure Terminal Pipe Plug Safety Wire Retaining Ring Capscrew Seal Plate -00- Impeller.00" dia 0, -00- Impeller.00" dia -00- Impeller.00" dia -0- Impeller.0" dia -0- Impeller.00" dia Impeller Washer Capscrew Wearing Ring Lower Seal, Ceramic (std) S Lower Seal, Carbide (opt) C -00- Volute Capscrew Bearing Housing Upper Seal SC Capscrew Capscrew RTF Stator RTF Shaft Sleeve SC Motor Housing HP 0 RPM, and All 0 RPM -00- Motor Housing, HP 0 RPM,,., HP 0 RPM Spacer 0 HP 0 RPM Spacer & HP 0 RPM Spacer & HP 0 RPM 0A0 Upper Bearing Load Spring Jam Nut Eye Bolt Connection Box #- 0, 0 DUAL VOLTAGE PHASE MOTOR WIRING 0V ø 0V ø BL W R (L) (L) (L) BL W R (L) (L) (L) 0-0 HP //0 RPM,.,, HP //0 RPM HP 00//0 RPM & HP 00///0 RPM Connection Box #-,., HP 0/0//0 RPM & HP 0/0//0 RPM Connection Box #- 0 HP 00//0 RPM 0 & 0 HP //0 RPM.,, Connection Box #- 0 HP 0/0//0 RPM -0 HP 0//0 RPM -0 HP 0//0 RPM Connection Box #- -0 HP 00//0 RPM 0 HP 0//0 RPM O-Ring SC Capscrew SST Capscrew SST Key Roll Pin Setscrew Labyrinth Ring Screen Seal Kit 00-- Carbide Seal Kit Fill Oil to above the Motor Windings

8 SKX Parts List Cord Cap Assy Connector 0 HP 0/0//0 RPM -0 HP 0//0 RPM 0-0 HP //0 RPM Connector -0 HP 00//0 RPM -0 HP 0//0 RPM Connector -0 HP 0//0 RPM Connector 0-0 HP 00//0 RPM 0 HP 0/0//0 RPM -0 HP 0//0 RPM 0 HP 0//0 RPM Connector 0 HP 00//0 RPM 0 HP 0//0 RPM O-Ring SC Connector Connector 0 HP 00//0 RPM -0 HP 0//0 RPM Connector 0 HP 0/0//0 RPM Connector -0 HP 00//0 RPM -0 HP 0//0 RPM Connector 0-0 HP //0 RPM O-Ring Stator Holding Ring Lower Bearing O-Ring SC Seal Sensor Assy Seal Failure Terminal Pipe Plug Safety Wire SC Retaining Ring Capscrew Shaft Sleeve SC Seal Plate 0-0- Impeller." dia Impeller.00" dia Impeller.0" dia Impeller.00" dia Roll Pin Impeller Washer Capscrew Wearing Ring Lower Seal, Ceramic (std) S Lower Seal, Carbide (opt) C Volute Capscrew Retaining Ring -00- Bearing Housing Upper Seal SC Capscrew Key Capscrew RTF Stator RTF Rotor & Shaft -00- Motor Housing -00- Screen Spacer 0 HP 0 RPM Upper Bearing Load Spring Jam Nut Eye Bolt Connection Box #- 0-0 HP //0 RPM Connection Box #- 0 HP 00//0 RPM Connection Box #- 0-0 HP 0/0//0 RPM 0 HP 00//0 RPM 0 HP 0//0 RPM Connection Box #- -0 HP 00//0 RPM 0 HP 0//0 RPM O-Ring SC CONNECTION DIAGRAM FOR LEADS IN MOTOR AND CONNECTION BOX (Y) WYE MOTOR CONNECTIONS 0 VOLTS 0 VOLTS L L L L L L Capscrew SST Capscrew SST Setscrew Labyrinth Ring Seal Kit 00-- Carbide Seal Kit 0, 0 0 Fill Oil to above the Motor Windings

9 SQX Parts List RTF Cord Cap Assy Connector, HP 0/0//0 RPM Connector 0 HP 00, 0/0//0 RPM Connector -0 HP 0 & 0//0 RPM Connector -0 HP 0 & //0 RPM Connector 0,, 0 HP //0 RPM Connector 0 HP 0/0//0 RPM O-Ring SC Connector Connector 0 HP 00//0 RPM 0, 0, 0 HP 0//0 RPM 0 & 0 HP //0 RPM Connector 0 HP 0/0//0 RPM Connector & 0 HP 00//0 RPM 0 & 0 HP 0//0 RPM HP 0//0 RPM Connector HP 0//0 RPM Connector 0,, 0 HP //0 RPM -0 HP 0//0 RPM Connector -0 HP 0//0 RPM 0A00 O-Ring SC Stator Holding Ring Lower Bearing O-Ring SC Seal Sensor Assy Seal Failure Terminal Pipe Plug Safety Wire Retaining Ring Capscrew Seal Plate -00- Impeller.00" dia -00- Impeller.0" dia -00- Impeller.00" dia -00- Impeller.0" dia -00- Impeller.00" dia -0- Impeller.0" dia -0- Impeller.00" dia Impeller Washer Capscrew Wearing Ring Lower Seal, Ceramic (std) S Lower Seal, Carbide (opt) C -00- Volute 0A0 Capscrew -00- Bearing Housing Upper Seal SC Capscrew Capscrew RTF Stator RTF Rotor & Shaft Motor Housing HP 0 RPM, and All 0 RPM Spacer 0 HP 0 RPM Upper Bearing Load Spring Jam Nut Eye Bolt Connection Box #- 0-0 HP //0 RPM Connection Box # Connection Box #- 0 HP 00//0 RPM 0 & 0 HP //0 RPM Connection Box #- 0 HP 0/0//0 RPM -0 HP 0//0 RPM Connection Box #- -0 HP 00//0 RPM O-Ring SC A0 Capscrew SST A0 Capscrew SST Key Roll Pin Fill Oil to above the Motor Windings 0, DUAL VOLTAGE PHASE MOTOR WIRING 0V ø 0V ø BL W R (L) (L) (L) BL W R (L) (L) (L) Setscrew Labyrinth Ring -00- Screen Shaft Sleeve Seal Kit 00-- Carbide Seal Kit Screw Adapter Wear Ring -00- Adapter Volute Gasket Retaining Ring 0, 0

10 HQX Parts List RTF Cord Cap Assy Connector 0 HP 0/0//0 RPM -0 HP 0//0 RPM 0-0 HP //0 RPM Connector -0 HP 00//0 RPM -0 HP 0//0 RPM Connector -0 HP 0//0 RPM Connector 0-0 HP 00//0 RPM 0 HP 0/0//0 RPM -0 HP 0//0 RPM 0 HP 0//0 RPM Connector 0 HP 00//0 RPM 0 HP 0//0 RPM O-Ring SC Connector Connector 0 HP 00//0 RPM -0 HP 0//0 RPM Connector 0 HP 0/0//0 RPM Connector -0 HP 00//0 RPM -0 HP 0//0 RPM Connector 0-0 HP //0 RPM O-Ring Stator Holding Ring Lower Bearing O-Ring SC Seal Sensor Assy Seal Failure Terminal Pipe Plug Safety Wire SC Retaining Ring Capscrew Shaft Sleeve Seal Plate -00- Impeller " dia Impeller.00" dia -00- Impeller " dia -00- Impeller.00" dia Key Impeller Washer Capscrew -00- Wearing Ring Lower Seal, Ceramic (std) S Lower Seal, Carbide (opt) C -00- Volute Capscrew Retaining Ring -00- Bearing Housing Upper Seal SC Capscrew Roll Pin Capscrew RTF Stator RTF Rotor & Shaft -00- Motor Housing -00- Screen Spacer 0 HP 0 RPM 0A0 Upper Bearing Load Spring Jam Nut Eye Bolt Connection Box #- 0-0 HP //0 RPM Connection Box #- 0 HP 00//0 RPM Connection Box #- 0-0 HP 0/0//0 RPM 0 HP 00//0 RPM 0 HP 0//0 RPM Connection Box #- -0 HP 00//0 RPM 0 HP 0//0 RPM O-Ring SC A0 Capscrew SST A0 Capscrew SST Setscrew Labyrinth Ring Seal Kit 00-- Carbide Seal Kit 0, 0 0 Fill Oil to above the Motor Windings

11 SLVX Parts List RTF Cord Assy, Connector HP 00//0 RPM HP 0/0//0 RPM HP //0 RPM HP 0/0//0 RPM HP //0 RPM 0 HP 0/0//0 -/ HP RPM -/ HP 0/0//0 RPM -0 HP // Connector 0 HP 0//0 RPM Connector 0 HP 00//0 RPM 0 0/0//0 RPM 0 HP 0//0 RPM 0 HP 0//0 RPM Connector 0 HP 0//0 RPM Connector HP 0/0//0 RPM HP 0/0//0 RPM Connector HP 0/0//0 RPM HP 0/0//0 RPM Connector 0 HP 0/0//0 RPM O-Ring SC Connector Connector HP 00//0 RPM HP //0 RPM HP 00//0RPM HP //0 RPM HP 0/0//0 RPM HP 0/0//0 RPM Connector 0 HP 00//0 RPM 0 HP 0//0 RPM 0 HP // Connector 0 HP 0/0//0 RPM Connector 0 HP 0//0 RPM Connector HP 00//0 RPM -/ HP 00//0 RPM HP //0 RPM 0 HP //0 RPM 0 HP 0//0 RPM Key Stator Holding Ring Lower Bearing O-Ring SC Seal Sensor Assy Seal Failure Probe Pipe Plug O-Ring SC O-Ring SC Capscrew Shaft Sleeve SC Seal Plate -0- Impeller." dia. 0, 0-0- Impeller." dia. -0- Impeller." dia. -0- Impeller." dia Impeller.00" dia. -0- Impeller." dia Impeller." dia Impeller.0" dia Impeller.00" dia Key Impeller Washer Capscrew Roll Pin Lower Seal (Std.) S Lower Seal (Carbide) C Volute Capscrews Retaining Ring Bearing Housing Upper Seal SC Capscrew Screen Capscrew RTF Stator RTF Rotor & Shaft Motor Housing HP 0 RPM 0 HP 0 RPM -00- Motor Housing HP 0 RPM HP 0 RPM Labyrinth Ring Spacer HP 0 RPM HP 0 RPM & HP 0 RPM 0A0 Upper Bearing Bearing Adj. Spring Nut Bolt Connection Box #- -/ HP 00//0 RPM -/ HP //0 RPM -/ HP 00//0 RPM -/ HP //0 RPM -0 HP //0 RPM Connection Box #- -/ HP 0/0//0 RPM HP 0/0//0 RPM Connection Box #- 0 HP 00//0 RPM 0 HP 0//0 RPM Connection Box #- 0 HP 0/0//0 RPM Connection Box #- -0 HP 0//0 RPM O-Ring SC Capscrew SST Capscrew SST Seal Kit 00-- Carbide Seal Kit 0 Fill Oil to above the Motor Windings

12 SAX Parts List RTF Cord Cap Assy Connector & HP 00, 0/0, //0 RPM & HP 0/0//0 RPM & HP 00//0 RPM ,, HP 00 & //0 RPM HP 00, 0/0//0 RPM , HP 0/0//0 RPM , HP 0 & 0//0 RPM HP 0 & //0 RPM & 0 HP //0 RPM HP 0//0 RPM O-Ring SC Connector Connector. & HP //0 RPM & HP //0 RPM Connector. & HP 0/0//0 RPM & HP 0/0//0 RPM Connector 0, 0, 0 HP 0//0 RPM 0 & 0 HP //0 RPM Connector Connector & 0 HP 00//0 RPM 0 & 0 HP 0//0 RPM HP 0//0 RPM Connector HP 0//0 RPM Connector & 0 HP //0 RPM HP //0 RPM. & HP 00//0 RPM & HP 00//0 RPM 0 HP 0//0 RPM Connector 0 HP 0//0 RPM O-Ring SC Stator Holding Ring Lower Bearing O-Ring SC Seal Sensor Assy Seal Failure Terminal Pipe Plug Shaft Sleeve SC Retaining Ring Capscrew Seal Plate -00- Impeller.00" dia -00- Impeller.0" dia -00- Impeller.00" dia -0- Impeller.0" dia -0- Impeller.00" dia Impeller Washer Capscrew Wearing Ring Lower Seal, Ceramic (std) S Lower Seal, Carbide (opt) C -00- Volute 0 0, Capscrew Bearing Housing Upper Seal SC Capscrew Capscrew RTF Stator RTF Rotor & Shaft Motor Housing HP 0 RPM, all 0 RPM -00- Motor Housing & HP 0 RPM,. & HP 0 RPM Spacer HP 0 RPM Spacer & HP 0 RPM Upper Bearing Load Spring Jam Nut Eye Bolt Connection Box #- 0 HP //0 RPM.,, HP //0 RPM & HP 00///0 RPM Connection Box #-., HP 0/0//0 RPM & HP 0/0//0 RPM 0, DUAL VOLTAGE PHASE MOTOR WIRING 0V ø 0V ø BL W R (L) (L) (L) BL W R (L) (L) (L) Connection Box #- 0 & 0 HP //0 RPM.,, Connection Box #- 0 HP 0//0 RPM 0 HP 0//0 RPM Connection Box #- 0 HP 00//0 RPM 0 HP 0//0 RPM O-Ring SC Capscrew SST Capscrew SST Drivescrew Roll Pin Setscrew Labyrinth Ring Screen Key Seal Kit 00-- Carbide Seal Kit Fill Oil to above the Motor Windings

13 SLX Parts List RTF Cord Assy, Connector HP 00/0/0///0 RPM HP 0/0//0 RPM HP //0 RPM HP 0//0 RPM 0 HP 0//0 -/ HP 00//0 RPM -/ HP 0/0//0 RPM 0 HP // HP 0//0 RPM Connector 0 HP 00//0 RPM 0 HP 0/0//0 RPM 0 HP 0//0 RPM 0 HP 0//0 RPM Connector 0 HP 0//0 RPM Connector -/ HP 0//0 RPM HP 0//0 RPM Connector -/ HP 0//0 RPM HP 0//0 RPM Connector HP 0//0 RPM 0 HP 0//0 RPM O-Ring SC Connector Connector -/ HP 00//0 RPM -/ HP //0 RPM HP 00//0 RPM HP //0 RPM -/ HP 0/0//0 RPM HP 0/0//0 RPM Connector 0 HP 00//0 RPM 0 HP 0//0 RPM 0 HP // Connector 0 HP 0/0//0 RPM Connector 0 HP 0//0 RPM Connector HP 00//0 RPM -/ 0 HP 00//0 RPM HP //0 RPM 0 HP //0 RPM 0 HP 0/0//0 RPM Key Stator Holding Ring Lower Bearing O-Ring SC Seal Sensor Assy Seal Failure Terminal Pipe Plug 0A00 O-Ring SC O-Ring SC Capscrew Shaft Sleeve SC Seal Plate Impeller." Impeller.0" 0-0- Impeller." Impeller." 0-0- Impeller." Impeller.0" 0-0- Impeller.00" Impeller." 0-0- Impeller.0" 0-0- Impeller." Key Impeller Washer Capscrew Wearing Ring Lower Seal (Std) S Lower Seal (Carbide) C Volute 0A0 Capscrew Retaining Ring Bearing Housing Upper Seal SC Capscrew Screen Capscrew RTF Stator RTF Rotor & Shaft Motor Housing HP 0 RPM 0 HP 0 RPM -00- HP 0 RPM HP 0 RPM Labyrinth Ring Spacer HP 0 RPM 0 CONNECTION DIAGRAM FOR LEADS IN MOTOR AND CONNECTION BOX (Y) WYE MOTOR CONNECTIONS 0 VOLTS 0 VOLTS L L L L L L Spacer 0 HP 0 RPM Spacer & HP 0 RPM 0A0 Upper Bearing Bearing Adjusting Spring Nut Bolt Connection Box #- HP 00///0 RPM HP 00//0 RPM HP //0 RPM 0 HP //0 RPM Connection Box #- HP 0/0//0 RPM HP 0/0//0 RPM Connection Box #- 0 HP 00//0 RPM 0 HP 0//0 RPM Connection Box #- 0 HP 0/0//0 RPM Connection Box #- 0 HP 0//0 RPM O-Ring SC A0 Capscrew SST A0 Capscrew SST Setscrew Seal Kit 00-- Carbide Seal Kit Fill Oil to above Top of the Motor Windings

14 THIS PAGE INTENTIONALLY LEFT BLANK

15 THIS PAGE INTENTIONALLY LEFT BLANK

16 STANDARD LIMITED WARRANTY Pentair Hydromatic warrants its products against defects in material and workmanship for a period of months from the date of shipment from Pentair Hydromatic or months from the manufacturing date, whichever occurs first provided that such products are used in compliance with the requirements of the Pentair Hydromatic catalog and technical manuals for use in pumping raw sewage, municipal wastewater or similar, abrasive-free, noncorrosive liquids. During the warranty period and subject to the conditions set forth, Pentair Hydromatic, at its discretion, will repair or replace to the original user, the parts that prove defective in materials and workmanship. Pentair Hydromatic reserves the right to change or improve its products or any portions thereof without being obligated to provide such a change or improvement for prior sold and/or shipped units. Start-up reports and electrical schematics may be required to support warranty claims. Submit at the time of start up through the Pentair Hydromatic website: Warranty is effective only if Pentair Hydromatic authorized control panels are used. All seal fail and heat sensing devices must be hooked up, functional and monitored or this warranty will be void. Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. Under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility. This limited warranty will not apply: (a) to defects or malfunctions resulting from failure to properly install, operate or maintain the unit in accordance with the printed instructions provided; (b) to failures resulting from abuse, accident or negligence; (c) to normal maintenance services and parts used in connection with such service; (d) to units that are not installed in accordance with applicable local codes, ordinances and good trade practices; (e) if the unit is moved from its original installation location; (f) if unit is used for purposes other than for what it is designed and manufactured; (g) to any unit that has been repaired or altered by anyone other than Pentair Hydromatic or an authorized Pentair Hydromatic service provider; (h) to any unit that has been repaired using non factory specified/ OEM parts. Warranty Exclusions: Pentair HYDROMATIC MAKES NO EXPRESS OR IMPLIED WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. Pentair HYDROMATIC SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE. Liability Limitation: IN NO EVENT SHALL Pentair HYDROMATIC BE LIABLE OR RESPONSIBLE FOR CONSEQUENTIAL, INCIDENTAL OR SPECIAL DAMAGES RESULTING FROM OR RELATED IN ANY MANNER TO ANY Pentair HYDROMATIC PRODUCT OR PARTS THEREOF. PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY RESULT FROM IMPROPER INSTALLATION. Pentair HYDROMATIC DISCLAIMS ALL LIABILITY, INCLUDING LIABILITY UNDER THIS WARRANTY, FOR IMPROPER INSTALLATION. Pentair HYDROMATIC RECOMMENDS INSTALLATION BY PROFESSIONALS. Some states do not permit some or all of the above warranty limitations or the exclusion or limitation of incidental or consequential damages and therefore such limitations may not apply to you. No warranties or representations at any time made by any representatives of Pentair Hydromatic shall vary or expand the provision hereof. 0 EAST TH STREET 0 Pinebush Road, Unit # ASHLAND, OHIO, USA 0 CAMBRIDGE, ONTARIO, CANADA NT 0A PUMP Warranty Rev. /