FM800R SERVICE PARTS

Transcription

1 This parts list contains the service parts and wiring diagrams for this model. Check the model number in question to be sure that it is applicable to this parts list. Caution: This model ice maker has been manufactured in two voltages, for electrical components, check to be certain that the part is the correct voltage for the machine. TABLE OF CONTENTS Cabinet... 2 Refrigeration... Water... Gearmotor... Evaporator... Control Box... Remote Condenser... Wiring Diagrams...

2 May, 10 Page 1

3 Cabinet Assembly A Back Panel, Painted 2 A2-001 Top Panel, Painted A2-002 Top Panel, S.S. A0-001 Service Panel, Painted A0-002 Service Panel, S.S. A Right Side Panel, Painted A Right Side Panel, S.S Speed Clip Emblem Screw A2-001 Front Panel, Painted A2-002 Front Panel, S.S. A Base Assembly 10 A Tube Bracket 11 A Tube Bracket 12 A0-001 Control Box Support 1 A2-001 Left Side Panel, Painted A2-002 Left Side Panel, S.S Screw May, 10 Page 2

4 Refrigeration System Liquid Line Valve 220 v Liquid Line Valve 11 v Nut Washer A2-001 Receiver Brace A Receiver Mount Hi Pressure Cut Out Receiver Cap Screw Dryer Cap Screw Washer Sleeve Rubber Grommet Head Pressure Valve Thermo Expansion Valve 1 A Insulation Kit for TXV 1 A-001 Suction Line Core Nut A1-020 Evaporator Compressor v Overload v Compressor 11/0/ Overload 11/0/ Crankcase Htr v Crankcase Htr 11 v May 200 Page

5 Water System, Water Seal Cap Screw 2 A Water Level Sensor A1-020 Evaporator Res. Cover A Float Assembly with pin, housing seal, rubber seal, insert & float A Reservoir Assembly A2-001 Retaining Ring for Seal Half Union Strainer Tube,.2" req Tee Water Seal Water Shed 1 A Drip Pan 1 A Water Inlet Fitting Pal Nut Res. Overflow, " req Drain Casting Gasket Clamps Evap. Drain, 1" req Plug Evap. Inlet Tube, 1" req Tee 2 A Tube, Preformed Drain Tube, 2" req Lockwasher October 2011 Page

6 1 FM00R SERVICE PARTS Gearmotor *Note: Gearcase Cover includes: cover, output shaft, key, output gear, & bearings Water Shed 2 A2-02 Seal no number End bell A2-02 Bolt A2-022 Gearcase Cover* A2-02 1st Gear and Bearings A2-02 2nd Gear and Bearings A2-021 Gasket A2-020 Gearcase 10 A2-020 Centrifugal sw, GE PSC Start sw, Emerson Start sw, GE split phase Drive Motor-20-20v Drive Motor 11 v Rotor Bearing, GE PSC Rotor bearing, Emerson Rotor bearing, GE split phase 1 A2-02 Seal 1 A2-02 Oil, 1 Container Capacitor, GE PSC only September 2011 Page

7 Evaporator, Bin Controls Hex Stud 2. A Switch & housing assy Ice Chute Cover. A2-001 Insulation Top (half) Ice Chute Body. A Insulation Collar Inside A Rubber Band Ice Chute Lower. A0-021 Bin Controls Assy. (set). A Chute Gasket Hex Cap Screw Ice Sweep Water Shed Lip Seal Breaker Cover O-Ring Auger Stud & washer 1. part of 1 Thrust Washer 1. A-020 Bearing Lip Seal Screw September 2011 Page O-Ring Slotted Collar O-Ring Soc. Head Screw 2. A0-020 Breaker (Divider) (includes 1 & 1) 2. A Auger 2. A1-020 Evaporator Cap Screw Insulation wrap 0. A Drip Pan Drip Pan Gasket Water Shed O-ring

8 Control Box Start Cap v Start Capacitor 11 v Start Capacitor Cap Start Capacitor Bracket Screw Lockwasher Contactor v Contactor 11 v A0-022 Circuit Board Master Switch Low Pressure Control Potential Relay volt Potential Relay 11 volt Transformer 11v Transformer 220v no number Control Box Assy NOT ILLUSTRATED Pin Plug Assy (Safety Circuit to Circuit Board) Pin Plug Assy May 200 Page

9 REMOTE CONDENSER RC101-2A or RC102-2A Fan Guard Fan Blade Fan Motor RC Fan Guard Fan Blade Fan Motor May, 10 Page

10 Component Layout Diagram May, 10 Page

11 Schematic Diagram USE COPPER CONDUCTORS ONLY THIS UNIT MUST BE GROUNDED All Controls Shown in Normal Ice Making Mode. Note: Dashed lines indicate field wiring which must be installed in accordance with the National Electric Code Using a Minimum of 1 ga. awg. wire. May, 10 Page 10