Hydraulic Thruster Installation Guide

Size: px
Start display at page:

Download "Hydraulic Thruster Installation Guide"

Transcription

1 Hydraulic Thruster Installation Guide Hydraulic Thruster Installation Guide -

2 Change Log Date Change 03/11/2014 Initial converted release ABT-TRAC 517-A Martin Avenue Rohnert Park, CA Tel: Fax: Hydraulic Thruster Installation Guide -

3 ! IMPORTANT Confirm that all jog levers are in the center (OFF) position before pressing the green start button and activating any jog lever station. Failure to make this check prior to pressing Start or making all stations active, may result in unwanted thruster operation and harm to the vessel or its occupants. 1 Hydraulic Thruster Installation Guide

4 Important Notices The thruster tunnel is an integral part of the hull. Installation should be done only by professionals with certified competency in the fabrication and repair of the hull material in question. Your naval architect must confirm and certify proper mechanical bonding of the tunnel to the hull as well as proper support of the tunnel. Recommendations made by American Bow Thruster (ABT-TRAC) are to be used as guidelines only. ABT-TRAC is not a naval architecture firm and is not qualified to advise on structural matters. ABT-TRAC strongly recommends that you seek the advice of a naval architect familiar with your vessel. Precautions and Warnings Before installation, read and understand the information in this manual. The Hydraulic Thruster Installation Guide is intended for experienced marine engineering personnel. Proper general engineering standards and practices must be followed at all times. System Hydraulic Fluid Use only ISO 32 and ISO 46 hydraulic fluids in ABT-TRAC hydraulic systems. Using any other fluid voids the Arcturus Marine Systems warranty. Corrosion Control All seagoing vessels must be protected from corrosion from galvanic and electrolytic potential. ABT-TRAC encourages all boat owners to enlist the services of a corrosion control expert to evaluate their vessel s corrosion control system and how their thrusters should be made a part of that system. ABT-TRAC thrusters are particularly resistant to all types of corrosion, especially bronze models. Serious corrosion problems, however, can take their toll on all types of equipment, especially on aluminum boats. Whatever system you use, you must take the thruster system into consideration and include it in your corrosion control system. Paint and Coatings On Hydraulic Systems Reservoirs, heat-exchangers, and bell housings are painted with Dupont 25P epoxy primer and IMRON 333 white polyurethane. These are the only components painted on a regular basis. The same coatings are used when requests are made that other components in the system be painted. On Thrusters, Propellers, and Tunnels Use bottom paint on thrusters and tunnels; use any available advanced propeller coating on propellers. Standard Warranty This warranty is offered by Arcturus Marine Systems, dba American Bow Thruster or ABT-TRAC. ABT-TRAC warrants all new products and systems to be free from defects in material and workmanship for a period of ONE YEAR from the date of system commissioning. Defective parts will be repaired or replaced at ABT-TRAC s option. Customer is responsible for freight costs associated with returning parts to ABT-TRAC. ABT-TRAC will pay freight costs, including air freight, for the shipment of repaired or replacement parts back to customer (local laws may apply). Hydraulic Thruster Installation Guide 2

5 This warranty does NOT cover failure of parts due to mis-installation, damage, accidents, improper storage, or misuse. Labor for parts removal and reinstallation is NOT covered. Arcturus Marine Systems (ABT-TRAC) shall NOT be liable for special, incidental, or consequential damages of any kind including but not limited to vessel haulout costs or lost revenue. The warranties described above shall be the sole and exclusive warranties granted by ABT-TRAC and shall be the sole and exclusive remedy available to the purchaser. 3 Hydraulic Thruster Installation Guide

6 Tunnel Position Figure 1. Proper Tunnel Position Installing the Tunnel Waterline At least one diameter below waterline and one diameter above the keel Position the tunnel as far forward as possible while maintaining adequate tunnel length. Ideally, the tunnel should be three diameters long, and at minimum, it must be long enough so that no part of the thruster protrudes beyond the tunnel opening. Marking the Tunnel Cutout 1. Carefully measure and mark the center point of the tunnel on both sides of the hull interior; make sure the location is square in all directions. 2. Drill a 3/16 ( mm) diameter hole at each center point. As far forward as possible 3. Bend a 1/8 (3.175 mm) steel rod into a scribing tool with a diameter equal to the tunnel s outside diameter radius. Figure 2. Scribing the Tunnel Opening Tunnel outside diameter radius 4. Pass the scribing tool through the holes in the hull and scribe the tunnel openings on both sides of the hull. 5. Carefully cut the tunnel openings at the scribe marks, keeping the cutting tool parallel to the ground. Hydraulic Thruster Installation Guide 4

7 6. Round-over the edge of the tunnel where it meets the hull to 1/10 the tunnel diameter. This minimizes inlet turbulence. One-tenth the tunnel diameter is the ideal radius, but may not always be practical. On metal tunnels where performance is critical, use a 45 chamfer. Figure 3. Ideal Tunnel Radius 1/10 the tunnel diameter roundover or 45o chamfer Reducing Drag There are two hull modifications that may help to reduce drag near the tunnel opening: creating an eyebrow or scalloping the hull as shown in Figure 4 and Figure 5. Figure 4. Eyebrow Hull Modification Eyebrow Figure 5. Scallop Hull Modification Scallop 5 Hydraulic Thruster Installation Guide

8 Tunnel Grates Tunnel grates keep people, animals, and debris out of the thruster tunnel, as well as possibly reduce tunnel drag and propeller freewheeling. Install grates vertically with the bars approximately 3.5 (89 mm) to 5 (127 mm) apart. Figure 6. Proper Tunnel Grate Orientation X Hydraulic Thruster Installation Guide 6

9 Installing the Thruster Refer to the following installation diagrams for your thruster size. In general, the thruster is mounted in the tunnel with screws and a gasket. Be sure to check for sufficient propeller clearance before final installation; using the supplied gasket is not required and is dependent on the amount of propeller clearance.! IMPORTANT After installing the thruster, be sure to install the header tank before starting the system (refer to Mounting the Header Tank on page 13). 7 Hydraulic Thruster Installation Guide

10 Hydraulic motor shaft Magnaloy coupling Coupling insert Bell housing Hydraulic motor 8 TRAC Installation Motor mounting bolts (2 or 4) Use medium strength locking compound Tighten to 40 ft/lbs (54.23 nm) Key Leave (1.27 mm) gap in coupling assembly Bell housing mounting bolts (7) Use high strength locking compound Tighten to 24 ft/lbs (32.54 nm) evenly! IMPORTANT Bell housing heights vary; be sure that there is (2.54 mm 8.89 mm) clearance between the ends of the hydraulic motor and the pinion shaft (check this clearance by dry-fitting the motor without the spline coupling) Header tank fitting Install header tank before starting system Tunnel Mounting gasket Coat both sides with high quality marine sealant such as 3M 4200, 5200, or 4000 Remove set-screw before installing bell housing Make sure O-ring is in place before installing bell housing (p/n Standard AS568A #011 or #904) Thruster mounting bolts Key Pinion shaft There are a total of six thruster-mounting bolts Use anti-seizing compound on each bolt Use safety wire to secure bolts (see below) Tighten to 24 ft/lbs (32.54 nm) Propeller Cotter pin Nut Coat shaft threads with high strength locking compound Tighten to 50 ft/lbs (67.8 nm) Key Bell Housing Top View Safety Wire Guide Header tank breather fitting port Hydraulic Thruster Installation Guide 8

11 10 and 12 TRAC Installation Motor mounting bolts (2) Use medium strength locking compound Tigten to 50 ft/lbs (67.8 nm) Spline coupling Apply heavy grease Bell housing Header tank fitting Install header tank before starting system Tunnel Hyhdraulic motor Hyhdraulic motor shaft Bell housing mounting bolts (7) Use high strength locking compound Tighten to 24 ft/lbs (32.54 nm) evenly Make sure O-ring is in place before installing bell housing (p/n Standard AS568A #011 or #904) Thruster mounting bolts! IMPORTANT Bell housing heights vary; be sure that there is (2.54 mm 8.89 mm) clearance between the ends of the hydraulic motor and the pinion shaft (check this clearance by dry-fitting the motor without the spline coupling) There are a total of six thruster-mounting bolts in two diameters Use anti-seizing compound on each bolt Use safety wire to secure bolts (see below) Tighten 3/8 bolts to 24 ft/lbs (32.54 nm) Tighten 1/2 bolts to 50 ft/lbs (67.8 nm) Mounting gasket Coat both sides with high quality marine sealant such as 3M 4200, 5200, or 4000 Pinion shaft Remove set-screw before installing bell housing Propeller Cotter pin Nut Coat shaft threads with high strength locking compound Tighten to 80 ft/lbs ( mm) Nose cone Key Fasteners Coat with medium strength locking compound Tighten to 7 ft/lbs (9.49 nm) Bell Housing Top View Safety Wire Guide 9 Hydraulic Thruster Installation Guide

12 16 TRAC Installation SAE spline adapter (If applicable) Spline coupling Header tank fitting Install header tank before starting system Hydraulic motor Motor mounting bolts (2 or 4) Use medium strength locking compound Tighten to 50 ft/lbs (67.8 nm) Hydraulic motor shaft Bell housing mounting bolts (7) Use high strength locking compound Tighten to 24 ft/lbs (32.54 nm) evenly Bell housing Bell housing stabilizer bolts Use high strength locking compound Tighten to 5 ft/lbs (6.78 nm)! IMPORTANT Bell housing heights vary; be sure that there is (2.54 mm 8.89 mm) clearance between the ends of the hydraulic motor and the pinion shaft (check this clearance by dry-fitting the motor without the spline coupling) Tunnel Thruster mounting bolts There are a total of six thruster-mounting bolts in two diameters Use anti-seizing compound on each bolt Use safety wire to secure bolts (see below) Tighten 3/4 bolts to 100 ft/lbs ( nm) Tighten 3/8 bolts to 24 ft/lbs (32.54 nm) Mounting gasket Coat both sides with high quality marine sealant such as 3M 4200, 5200, or 4000 Remove set-screw before installing bell housing Make sure O-ring is in place before installing bell housing (p/n Standard AS568A #011 or #904) Pinion shaft Propeller Cotter pin Nut Coat shaft threads with high strength locking compound Tighten to 100 ft/lbs ( nm) Key Nose cone Fasteners Coat with medium strength locking compound Tighten to 7 ft/lbs (9.49 nm) Bell Housing Bottom View Safety Wire Guide Header tank breather fitting Make sure O-ring is in groove before installing bell housing Hydraulic Thruster Installation Guide 10

13 SAE spline adapter (If applicable) Spline coupling Header tank fitting Install header tank before starting system Bell housing Hydraulic motor 20 TRAC Installation Motor mounting bolts (2 or 4) Use medium strength locking compound Tighten 5/8 bolts to 80 ft/lbs ( nm) Tighten 1/2 bolts to 50 ft/lbs (67.8 nm) Hydraulic motor shaft Bell housing mounting bolts (7) Use high strength locking compound Tighten to 50 ft/lbs evenly (67.8 nm) Bell housing stabilizer bolts Use high strength locking compound Tighten to 5 ft/lbs (6.78 nm)! IMPORTANT Bell housing heights vary; be sure that there is (2.54 mm 8.89 mm) clearance between the ends of the hydraulic motor and the pinion shaft (check this clearance by dry-fitting the motor without the spline coupling) Tunnel Thruster mounting bolts There are a total of six thruster-mounting bolts Use anti-seizing compound on each bolt Use safety wire to secure bolts (see below) Tighten to 100 ft/lbs ( nm) Mounting gasket Coat both sides with high quality marine sealant such as 3M 4200, 5200, or 4000 Make sure O-ring is in place before installing bell housing (p/n Standard AS568A #011 or #904) Pinion shaft Propeller Cotter pin Nut Coat shaft threads with high strength locking compound Tighten to 125 ft/lbs ( nm) Nose cone Key Fasteners Coat with medium strength locking compound Tighten to 7 ft/lbs (9.49 nm) Washer (if provided) Bell Housing Top View Safety Wire Guide Header tank breather fitting 11 Hydraulic Thruster Installation Guide

14 Hydraulic motor shaft SAE spline adapter (If applicable) Spline coupling Header tank fitting Install header tank before starting system Bell housing 24 and 28 TRAC Installation Hydraulic motor Motor mounting bolts (2 or 4) Use medium strength locking compound Tighten to 80 ft/lbs ( nm) Bell housing mounting bolts (7) Use high strength locking compound Tighten to 50 ft/lbs (67.8 nm) evenly Bell housing stabilizer bolts Use high strength locking compound Tighten to 5 ft/lbs (6.78 nm)! IMPORTANT Bell housing heights vary; be sure that there is (2.54 mm 8.89 mm) clearance between the ends of the hydraulic motor and the pinion shaft (check this clearance by dry-fitting the motor without the spline coupling) Tunnel Thruster mounting bolts There are a total of six thruster-mounting bolts in two diameters Use anti-seizing compound on each bolt Use safety wire to secure bolts (see below) Tighten 3/4 bolts to 135 ft/lbs ( nm) Tighten 7/8 bolts to 225 ft/lbs ( nm) Mounting gasket Coat both sides with high quality marine sealant such as 3M 4200, 5200, or 4000 Remove set-screw before installing bell housing Make sure O-ring is in place before installing bell housing (p/n Standard AS568A #011 or #904) Pinion shaft Propeller Washer (if provided) Cotter pin Nut Coat shaft threads with high strength locking compound Tighten to 150 ft/lbs ( nm) Nose cone Key Fasteners Coat with medium strength locking compound Tighten to 7 ft/lbs (9.49 mm) Bell Housing Top View Safety Wire Guide Header tank breather fitting Install header tank before starting system Hydraulic Thruster Installation Guide 12

15 Mounting the Header Tank! IMPORTANT On some systems, the header tank fitting and plumbing must be connected before the drive line or motor are installed, otherwise they cannot be accessed. The fluid level in the header tank must be monitored regularly and the tank must be kept one-half full. Use only Chevron Delo Gear Lubricant SAE to fill the header tank; the thruster is shipped pre-filled. Figure 7 shows the proper header tank location. Figure 7. Header Tank Location Remove cap Fill 1/2 full Header Tank Waterline Secure hose to hull or bulkhead with nylon straps or clamps 30 (762 mm) Minimum 13 Hydraulic Thruster Installation Guide

16 Installing the Thruster Hydraulics Figure 8 shows how to attach the thruster to the hydraulic system.! IMPORTANT Figure 8 illustrates only a small portion of the entire hydraulic system. Refer to the Hydraulic Installation Guide and your vessel s particular hydraulic system diagram for more detail. The directional control valve in the diagram is the most popular model; other models are available, but the connection criteria are the same. The system pressure line attaches to the port labeled P The tank return line attaches to the port labeled T (on the back in the diagram) The lines between the directional control valve and the thruster motor are attached to the ports labeled A and B Figure 8. Attaching Thruster to the Hydraulic System To Tank Return (on back) A P B From Main System A B To Case Drain Hydraulic Thruster Installation Guide 14

17 Installing Electrical Components Installing Thruster Control Stations Install Thruster Control Stations (TCSs) at steering stations near the main engine throttle and shift controls. A console cutout template and gasket are provided with each TCS. Make the console cutout as shown and drill the four mounting holes. The TCS mounts with four pre-installed stainless studs. Extra long coupling nuts are provided for tightening. On variable speed TCSs there are three electronic adjustments (pots) that must be adjusted at startup. Keep this in mind when locating the TCS and before securing in place. The portion of the TCS that extends below the console is not weather resistant. In situations where the area below the mounting surface is open to the environment, fabricate and install a protective cover for the bottom of the TCS. Figure 9. Thruster Control Stations Central Control PLC/Switch Box Mount the central control PLC/switch box in the engine room in a dry, central location, where the ambient temperature will not exceed 120 F (48.89 C). Access to the relay box is key in troubleshooting. Nearly all control wiring leads to the central control PLC/switch box. Run all wires in the sizes indicated on the accompanying wiring diagram. Figure 10. Central Control PLC/Switch Box Wiring Terminal Strip Glass Fuses PLC Micro Controller Control Relays 15 Hydraulic Thruster Installation Guide

18 Wiring The system must be wired according to the wiring diagram that accompanies this document. Wire sizes in the diagram are minimum sizes. Using wire of insufficient size can cause system malfunction and equipment damage. It may also result in a fire, which can cause significant material damages and serious personal injury. TCS Generic Wiring Diagram Figure 11 on page 17 illustrates generic TCS wiring. Hydraulic Thruster Installation Guide 16

19 Figure 11. Generic Wiring Diagram for the TCS WN SH (+) ( ) 24 VDC G 1 2 J1R J2R J3R ST ST J1+ #1 J1R #2 ST #3 AL #4 NEG #5 A1 #6 STATION 1 RED V(+) G ORN START YEL STOP GRN/WHT A1 BRN/WHT B1 WHT/BLK T1 AL AL J1+ J2+ J3+ B1 #7 GRN A2 T1 #8 BRN B2 A2 #9 WHT T2 B2 #10 BLU ALARM T2 #11 BLK V( ) R SPARE #12 STATION 2 J2+ #1 RED V(+) J2R #2 ORN START G ST #3 YEL STOP AL #4 GRN/WHTA1 NEG#5 BRN/WHTB1 A1 #6 WHT/BLK T1 B1 #7 T1 #8 A2 #9 B2 #10 T2 #11 SPARE #12 GRN A2 BRN B2 WHT T2 BLU ALARM BLK V( ) R A1 A1 A1 B1 B1 B1 T1 T1 T1 A2 A2 A2 B2 B2 B2 T2 T2 T2 FIV WX W PA DF DX DF DX FWD ISOLATION VALVE PUMP CONTROL HIGH PRESSURE SOLENOID J3+ J3R A2 B2 T2 NEG RED ORN STERN THRUSTER DCV STATION 3 V(+) START G 1 2 G P A B G 2 T A1 B1 T1 NEG BOW THRUSTER DCV 1 G 2 1 P G A 2 1 B G 2 T 1. Start button (JR) creates a ground input to PLC requesting power to selected station on J+. Pressing Start twice powers all stations including remote, if installed. Power is available for deck function on W, if applicable. Forward Isolation Valve (FIV) powers, if applicable. 2. Directional input from the jog lever sends +VDC to a directinoal input (A1, B1, etc.) and brings the system to high pressure through a _VDC output on PA and power direction on thruster DCV. 3. Throttle is provided from the TCS to T with a variable +VDC output to the DCV. NEG 4. Low oil level or high temperature create an open circuit on W for a warning tone every 3 seconds. Open on SH disables all stations and returns the system to standby pressure and creates a tone every second. Do not turn off power to switch box to silence alarm. System can continue to overheat with breaker off. 17 Hydraulic Thruster Installation Guide

THRUSTER 12 & 24 VDC Motors

THRUSTER 12 & 24 VDC Motors THRUSTER 12 & 24 VDC Motors 12V 24V Motor Installation Manual 12&24 VDC Motors Thruster Installation Manual April 2013 Western Marine Electronics 14120 NE 200th Street, Box 7201 Woodinville, WA 98072-4001

More information

BOW THRUSTER V2-10, V2-12, V2-16, V2-18, V2-20. Saddle Housing Installation Manual

BOW THRUSTER V2-10, V2-12, V2-16, V2-18, V2-20. Saddle Housing Installation Manual BOW THRUSTER V2-10, V2-12, V2-16, V2-18, V2-20 Saddle Housing Installation Manual Saddle Thruster Installation Manual JUNE 2012 Western Marine Electronics 14120 NE 200th Street, Box 7201 Woodinville, WA

More information

Single Colour Light. TIX202 Interchangeable Flush Fit Thru-Hull Light. Installation and Operation Guide. Rev

Single Colour Light. TIX202 Interchangeable Flush Fit Thru-Hull Light. Installation and Operation Guide. Rev Single Colour Light TIX202 Interchangeable Flush Fit Thru-Hull Light Installation and Operation Guide Rev 3 45-0038 Congratulations! You have purchased a LUMISHORE advanced technology LED underwater light.

More information

MV3-E Series Installation and Operation Manual for Hybrid Engine Controls

MV3-E Series Installation and Operation Manual for Hybrid Engine Controls MV3-E Series Installation and Operation Manual for Hybrid Engine Controls ISCHMV3E Revision 1.0 Notice to Boat Manufacturer, Installer, and Consumer Please read these instructions through carefully and

More information

INSTALLATION AND MAINTENANCE MANUAL FORM #PM-126 REV A 12/09

INSTALLATION AND MAINTENANCE MANUAL FORM #PM-126 REV A 12/09 HAND CRANK & MOTORIZED POWER CORD REELS: SERIES 1125PC SERIES: 1125PC HAND CRANK SERIES: 1125PC MOTORIZED COXREELS The technical data and images which appear in this manual are for informational purposes

More information

Neptune X6 12/24V SAE 316L Stainless Steel Low Profile Through-Hull Mounted Underwater LED Light Manual

Neptune X6 12/24V SAE 316L Stainless Steel Low Profile Through-Hull Mounted Underwater LED Light Manual Neptune X6 12/24V SAE 316L Stainless Steel Low Profile Through-Hull Mounted Underwater LED Light Manual Thank you for purchasing Dr. LED s Neptune X6 underwater LED light. This 1500+ lumen Neptune X6 underwater

More information

Single Colour Light. TIX301 Interchangeable Flush Fit Thru-Hull Light. Installation and Operation Guide

Single Colour Light. TIX301 Interchangeable Flush Fit Thru-Hull Light. Installation and Operation Guide Single Colour Light TIX301 Interchangeable Flush Fit Thru-Hull Light Installation and Operation Guide Congratulations! You have purchased a LUMISHORE advanced technology LED underwater light. Every care

More information

This Manual Provides Installation and Operation Instructions for the following models:

This Manual Provides Installation and Operation Instructions for the following models: OWNER'S MANUAL Capstan Powered Lift Assist This Manual Provides Installation and Operation Instructions for the following models: CAPSTAN 1000 CAPSTAN 300 QUICK CATCH POT PULLER pwcs101 12 Volt Powered

More information

ATD-7384W 12-Ton Bottle Jack Owner s Manual

ATD-7384W 12-Ton Bottle Jack Owner s Manual ATD-7384W 12-Ton Bottle Jack Owner s Manual Features: Specifications Made in China to ATD Tools, Inc. Specifications Visit us at www.atdtools.com ATD7384W_rev_0118 Product Description NOT Safety Precautions

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers recommended vehicle

More information

Model AM2 M40 Panel Installation, Operation, and Maintenance Manual

Model AM2 M40 Panel Installation, Operation, and Maintenance Manual Model AM2 M40 Panel Installation, Operation, and Maintenance Manual RECEIVING AND INSPECTION Upon receiving unit, check for any interior and exterior damage, and if found, report it immediately to the

More information

StormPro BA Series Sump Pump

StormPro BA Series Sump Pump Page 1 of 8 Marks & Meanings DANGER: Keep the pump equipment out of the reach of children! Warns that the failure to follow the directions given could cause serious risk to individuals or objects. WARNING:

More information

Installation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab

Installation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers

More information

CHEVY TRUCK INSTALLATION INSTRUCTIONS KIT SUM

CHEVY TRUCK INSTALLATION INSTRUCTIONS KIT SUM 1988-1994 CHEVY TRUCK INSTALLATION INSTRUCTIONS KIT SUM-7810013 Installation of a body lift will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center

More information

Easy/Tran TF STANDBY POWER FURNACE SWITCH TOOLS NEEDED FOR INSTALLATION. PARTS LIST for Easy / Tran TF FURNACE TRANSFER SWITCH

Easy/Tran TF STANDBY POWER FURNACE SWITCH TOOLS NEEDED FOR INSTALLATION. PARTS LIST for Easy / Tran TF FURNACE TRANSFER SWITCH STANDBY POWER FURNACE SWITCH Easy/Tran TF Congratulations on your purchase of the Reliance Controls Easy/Tran TF furnace transfer switch. Reliance has been manufacturing transfer switches and equipment

More information

Spare Parts, Instruction and Maintenance Manual for SPANCO Model 301 Jib Cranes

Spare Parts, Instruction and Maintenance Manual for SPANCO Model 301 Jib Cranes Manual No. 103-0007 REV. 6/10 Spare Parts, Instruction and Maintenance Manual for SPANCO Model 301 Jib Cranes ISO 9001 REGISTERED SPANCO, Inc. 2 TABLE OF CONTENTS Forward... 4 Installation... 4-6 Maintenance...

More information

FCB-450, LCB-600, MCB-800

FCB-450, LCB-600, MCB-800 AIR CHAMP PRODUCTS User Manual FCB-450, LCB-600, MCB-800 Clutch-Brakes (i) In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are

More information

Installation Instructions

Installation Instructions Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 8mm, 13mm, 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw, File WARNING: Under no circumstances do we recommend

More information

TIX402 EOS Installation and Operating Guide

TIX402 EOS Installation and Operating Guide TIX402 EOS Integrated System TIX402 EOS Installation and Operating Guide Congratulations! You have purchased a LUMISHORE advanced LED technology underwater lighting system. Every care has been taken to

More information

Elgin Hydraulic Clutch-Brake ECB-240, Product Number FORM NO. L F FORM NO. L F-0704

Elgin Hydraulic Clutch-Brake ECB-240, Product Number FORM NO. L F FORM NO. L F-0704 Elgin Hydraulic Clutch-Brake ECB-20, Product Number 96225 FORM NO. L-20283-F-070 1 FORM NO. L-20283-F-070 In accordance with Nexen s established policy of constant product improvement, the specifications

More information

Hydraulic Installation Guide

Hydraulic Installation Guide Hydraulic Installation Guide Version 1.0 Hydraulic Installation Guide - Version 1.0 Change Log Date Change 03/11/2014 Initial Release ABT-TRAC 517-A Martin Avenue Rohnert Park, CA 94928 Tel: 707-586-3155

More information

SV10 LED. The US manufactured SV10 LED is. SV10 LED technical specifications

SV10 LED. The US manufactured SV10 LED is. SV10 LED technical specifications The US manufactured SV10 LED is the brightest thru hull LED underwater light available to owners of GRP and wood boats. The industry leading SV10 combines the unique qualities of the latest high density

More information

Marine Products. SL-3 Engine Controls. Owner s Manual

Marine Products. SL-3 Engine Controls. Owner s Manual Marine Products SL-3 Engine Controls Owner s Manual This manual must be accessible to the owner/user of this Morse marine product. Includes installation, operation and maintenance instructions for your

More information

Power Float Manifold. Installation and Operations Manual Module 11A

Power Float Manifold. Installation and Operations Manual Module 11A Power Float Manifold Installation and Operations Manual Module 11A 2/14 Table of Contents 1 Features 3 2 Functional Purpose 3 3 4 Specifications System Installation 3 4 4.1 Hydraulic Connection 4 4.2 Electric

More information

Through-Shaft Clutch-Brake LSCB-32HT, LSCB-32HT, LSCB-44, LSCB-44HT, LSCB-54HT FORM NO. L D-0606 MEX (55) QRO (442)

Through-Shaft Clutch-Brake LSCB-32HT, LSCB-32HT, LSCB-44, LSCB-44HT, LSCB-54HT FORM NO. L D-0606 MEX (55) QRO (442) Through-Shaft Clutch-Brake LSCB-HT, LSCB-HT, LSCB-, LSCB-HT, LSCB-5HT In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject

More information

USER MANUAL. NEMA 48C Flange Mounted, Enclosed, Clutch Brake. FMCBE Model 500 FORM NO. L A (i)

USER MANUAL. NEMA 48C Flange Mounted, Enclosed, Clutch Brake. FMCBE Model 500 FORM NO. L A (i) USER MANUAL NEMA 48C Flange Mounted, Enclosed, Clutch Brake FMCBE Model 500 (i) In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 15/16, 10 mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating Saw 9464/9474 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING: Under

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill Short & Long Bed All Megacabs 9464/9474 HIDE-A-GOOSE HITCH INSTALLATION WARNING: Under no circumstances do we

More information

18VDC ESB6-X Series Cordless Screwdrivers Operation Manual

18VDC ESB6-X Series Cordless Screwdrivers Operation Manual 18VDC ESB6-X Series Cordless Screwdrivers Screwdriver Models : ESB6-X3.5, ESB6-X3.5F, ESB6-X5F ESB6-X6, ESB6-X9, ESB6-X12 CAUTION - Please read, understand, and follow all operating and safety instructions

More information

IS7.6 INSTALLATION MANUAL

IS7.6 INSTALLATION MANUAL IS7.6 INSTALLATION MANUAL #12501 MIN. 13.5" 1" 1" 29-7/8" 3" 14-7/8" 3" 20-7/8" 29-7/8" 24-5/8" Fig. 1 1 2 Fig. 2 Fig. 3 MAX. 80" MIN. 12" IS7.6 MIN. 8" Fig. 4 2 MIN. 6" MIN. 13.5" MIN. 12" MIN. 6" MIN.

More information

INSTALLATION HYPERCHARGER AIR FILTER KIT 9992

INSTALLATION HYPERCHARGER AIR FILTER KIT 9992 9992 PARTS INCLUDED 1 Chrome Hypercharger Assembly with Chrome Blood Groove Trap Door and Chrome Butterflies 1 Support Bracket 1 Breather Hardware Kit, including: 2 1-1/4 Breather Bolts 2 Breather Hoses

More information

Installation & Operation Instructions. Deluxe LED Spot Light

Installation & Operation Instructions. Deluxe LED Spot Light Installation & Operation Instructions Deluxe LED Spot Light 405626-3 To avoid the risk of accidents or damage to this product, it is essential to read these instructions thoroughly SDG Edition before this

More information

INSTALLATION MANUAL VAN SOLUTIONS FOR THE WAY YOU WORK. Model E. Terra Cotta Ave Fax

INSTALLATION MANUAL VAN SOLUTIONS FOR THE WAY YOU WORK. Model E. Terra Cotta Ave Fax VAN SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL Model 2291-3-01 Weather Guard / Knaack 800-456-7865 Toll Free 420 E. Terra Cotta Ave 800-334-2981 Fax Crystal Lake, IL 60014 USA Knaack.OrderEntry@wernerco.com

More information

Noran Tel. FUSE PANEL Technical Practice N21C110-NCY 5/5 GMT (20Amp GMT) NEBS Level 3 Certified

Noran Tel. FUSE PANEL Technical Practice N21C110-NCY 5/5 GMT (20Amp GMT) NEBS Level 3 Certified 0322-03D Sept 02, 2010 Noran Tel FUSE PANEL Technical Practice N21C110-NCY 5/5 GMT (20Amp GMT) NEBS Level 3 Certified FEATURES 2 isolated groups (busses) of 5 GMT fuses each (20Amps/GMT position). Polarity

More information

OWNER S MANUAL EVOLUTION 3500, 4500, 5500, & 8500 SERIES PUMPS

OWNER S MANUAL EVOLUTION 3500, 4500, 5500, & 8500 SERIES PUMPS OWNER S MANUAL EVOLUTION 3500, 4500, 5500, & 8500 SERIES PUMPS IMPORTANT SAFETY INSTRUCTIONS When installing and using this electrical equipment, basic safety precautions should always be followed, including

More information

INSTALLATION INSTRUCTIONS SINGLE HORIZONTAL ACCESS DOOR PANTRY INSERT MANUAL

INSTALLATION INSTRUCTIONS SINGLE HORIZONTAL ACCESS DOOR PANTRY INSERT MANUAL INSTALLATION INSTRUCTIONS MODEL #88972 SINGLE HORIZONTAL ACCESS DOOR PANTRY INSERT MANUAL TABLE OF CONTENTS PAGE # INSTALLATION INSTRUCTIONS...................2 CABINET LOCATION GUIDELINES...2 REGULAR

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 3/4, 15/16, 10mm, 18mm Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw 9465/9475 HIDE-A-GOOSE HITCH INSTALLATION All Fasteners Typical, Both Sides WARNING:

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS REV 3 05/13/2016 PART NO. RB610T RB620T PRODUCT DESCRIPTION: RB10 Hitch Step RB20 Hitch Step PRODUCT SAFETY & LEGAL DISCLAIMER IMPORTANT READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL INSTALLATION AND OPERATION MANUAL Models S120U & S240U Read all instructions before assembling or using the SunHeater system. Retain this manual for future use. TABLE OF CONTENTS Important Safety Information...2

More information

StormPro BCV400 Sewage Ejector Pump

StormPro BCV400 Sewage Ejector Pump Page 1 of 8 Marks & Meanings DANGER: Keep the pump equipment out of the reach of children! Warns that the failure to follow the directions given could cause serious risk to individuals or objects. WARNING:

More information

Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual. Lift-Rite Hand Pallet Trucks Model PST Plus

Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual. Lift-Rite Hand Pallet Trucks Model PST Plus Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual Lift-Rite Hand Pallet Trucks Model PST Plus This publication, 1269849/001B, applies to the Lift-Rite Hand Pallet Truck, Model

More information

Installation Instructions and Warranty Information

Installation Instructions and Warranty Information Installation Instructions and Warranty Information For JBA Headers 1997-2004 Chevrolet Corvette and z06 LS-1 / LS-6 V-8 Part# Application 1817 97-99 with 1-5/8 tube 1817-1 01-04 with 1-5/8 tube 1817-2

More information

INSTALLATION MANUAL VAN SOLUTIONS FOR THE WAY YOU WORK. Models & E. Terra Cotta Ave Fax

INSTALLATION MANUAL VAN SOLUTIONS FOR THE WAY YOU WORK. Models & E. Terra Cotta Ave Fax VAN SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL Models 2295-3-01 & 2297-3-01 Weather Guard / Knaack 800-456-7865 Toll Free 420 E. Terra Cotta Ave 800-334-2981 Fax Crystal Lake, IL 60014 USA Knaack.OrderEntry@wernerco.com

More information

Single-Position Detent Clutch DC Series. (i) MTY (81) MEX (55) QRO (442)

Single-Position Detent Clutch DC Series. (i) MTY (81) MEX (55) QRO (442) Single-Position Detent Clutch DC Series (i) FORM NO. L-2017-A-001 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject

More information

SPECIFICATIONS CONTENTS: Specifications Warning Information. Operating Instructions Preventative Maintenance Troubleshooting

SPECIFICATIONS CONTENTS: Specifications Warning Information. Operating Instructions Preventative Maintenance Troubleshooting Model 3182 2,500 Lbs Power Train Table/Lift OWNER'S MANUAL CONTENTS: Page 1 Page 2-3 Page 3 Page 4 Page 5 Page 5 Page 6 Page 7 Page 8 Specifications Warning Information Setup Operating Instructions Preventative

More information

Livorsi DTS Controls Installation and Operation Manual

Livorsi DTS Controls Installation and Operation Manual Livorsi DTS Controls Installation and Operation Manual for Triple/Quad Engine Digital Throttle and Shift Controls Revised JUNE 2017 LIT-CTL-DTS34 REV A ECO 28610 715 Center Street Grayslake IL 60030 P:

More information

DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual

DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual Installation Instructions Tech Support: 856.768.8300 TechSupport@GlowShiftGauges.com DUAL WIDEBAND AIR/FUEL RATIO GAUGE Product Numbers: GS-W702W_Dual, GS-C702W_Dual, GS-T702W_Dual (1) Gauge (2) Controllers

More information

Premium Supply. Tilt Deck. Models PCK-TD PCK-PTD. Operator s Manual and Installation Instructions

Premium Supply. Tilt Deck. Models PCK-TD PCK-PTD. Operator s Manual and Installation Instructions Tilt Deck Models PCK-TD PCK-PTD Operator s Manual and Installation Instructions Premium Supply 2038 West Interstate 30 866-934-0777 Proud members of: and June 1, 2015 Table of Contents Introduction...

More information

JEEP WRANGLER INSTALLATION INSTRUCTIONS KIT SUM

JEEP WRANGLER INSTALLATION INSTRUCTIONS KIT SUM 1986-1995 JEEP WRANGLER INSTALLATION INSTRUCTIONS KIT SUM-7893300 Installation of a body lift will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center

More information

INSTALLATION HYPERCHARGER AIR FILTER KIT 9754

INSTALLATION HYPERCHARGER AIR FILTER KIT 9754 9754 PARTS INCLUDED 1 Chrome Hypercharger Assembly 1 Support Bracket 1 Breather Hardware Kit, including: 2 1-1/4 Breather Bolts 2 Breather Hoses 4 Shim Washers 1 Twin Cam Breather Kit, Including: 1 Breather

More information

Sport Sway Bar Kit (22425) Scion tc

Sport Sway Bar Kit (22425) Scion tc Sport Sway Bar Kit (22425) Scion tc Thank you for your purchase from our new line of Scion tc parts. Please call us at (877) 4NO - ROLL if you have any questions regarding the service or installation of

More information

Stainless Steel Outboard Motor Brackets - Installation and Operating Instructions Models T10054 and T10055

Stainless Steel Outboard Motor Brackets - Installation and Operating Instructions Models T10054 and T10055 USER MANUAL OUTBOARD MOTOR BRACKETS Stainless Steel Outboard Motor Brackets - Installation and Operating Instructions Models T10054 and T10055 CAUTION Do not exceed the bracket s HP or weight limits. Read

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS REV 3 05/13/2016 INSTALLATION INSTRUCTIONS PART NO. 960001T 960003T PRODUCT DESCRIPTION: Full size Powered Light Bar Mid size Powered Light Bar Sport Bar and lights sold separately shown for reference

More information

Installation Instructions and Warranty Information

Installation Instructions and Warranty Information Installation Instructions and Warranty Information 1999 2003 Ford SuperDuty Truck and Excursion Part# 1669S, 1669S-1, 1669S-2 Read all instructions carefully before attempting installation. Rev. 10/05

More information

Installation, Operation and Maintenance Manual

Installation, Operation and Maintenance Manual IOM-HS-QTColdBevMax Installation, Operation and Maintenance Manual QT TM Cold Bev Max TM Models: QTCLDBMX-1S-.5M, QTCLDBMX-2S-.5M, QTCLDBMX-3S-.5M, QTCLDBMX-4S-.5M, QTCLDBMX-5S-.5M Tested and Certified

More information

½ DODGE CUMMINS OEM BYPASS LIFT PUMP KIT Installation Instructions Part #

½ DODGE CUMMINS OEM BYPASS LIFT PUMP KIT Installation Instructions Part # 29 July 2005 2003-04.5 Dodge Cummins OEM Bypass Lift Pump Kit # 1050227-1 - 2003-04½ DODGE CUMMINS OEM BYPASS LIFT PUMP KIT Installation Instructions Part # 1050227 PLEASE READ ALL INSTRUCTIONS CAREFULLY

More information

TECHNICAL SERVICE MANUAL

TECHNICAL SERVICE MANUAL Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL Viking In-Line Helical Gear Reducers Sizes 11, 21, 31, 35, 41, 51,

More information

Do not install and/or operate this safety product unless you have read and understand the safety information contained in this manual.

Do not install and/or operate this safety product unless you have read and understand the safety information contained in this manual. Installation and Operation Instructions MR Tri- Light Available in various color combinations, the MR Directional LED surface mount, tri-color warning light is ideal for a wide variety of auxiliary warning

More information

Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual. Lift-Rite Titan Series Hand Pallet Trucks Model LCF55 - Freezer Special

Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual. Lift-Rite Titan Series Hand Pallet Trucks Model LCF55 - Freezer Special Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual Lift-Rite Titan Series Hand Pallet Trucks Model LCF55 - Freezer Special Lift-Rite, 5975 Falbourne Street, Mississauga, Ontario

More information

SPL HICAS ELIMINATOR KIT

SPL HICAS ELIMINATOR KIT SPL HICAS ELIMINATOR KIT Steps to installing the Hicas eliminator kit: 1. Unbolt and remove Hicas actuator. 2. Remove Hicas ball joint and install toe bushing 3. Install Hicas eliminator bracket and toe

More information

INSTALLATION MANUAL VAN SOLUTIONS FOR THE WAY YOU WORK. Models & E. Terra Cotta Ave Fax

INSTALLATION MANUAL VAN SOLUTIONS FOR THE WAY YOU WORK. Models & E. Terra Cotta Ave Fax VAN SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL Models 2275-3-01 & 2277-3-01 Weather Guard / Knaack 800-456-7865 Toll Free 420 E. Terra Cotta Ave 800-334-2981 Fax Crystal Lake, IL 60014 USA Knaack.OrderEntry@wernerco.com

More information

Installation Instructions

Installation Instructions Equipment Required: Fastener Kit: F Wrenches: 15/16, 15/16 Crowfoot Adaptor Drill Bits: 1/4 Other Tools: Drill, Reciprocating saw Optional, Raise Bed: 18mm socket, 15 extension As an option you can loosen

More information

V HUB INSTALLATION AND OPERATING INSTRUCTIONS

V HUB INSTALLATION AND OPERATING INSTRUCTIONS 2008 Wood Court Plant City, FL 33563 USA Phone (813)752-3711 Fax (813)752-2818 http:\\www.sensenich.com Composite Airboat Propellers V HUB INSTALLATION AND OPERATING INSTRUCTIONS CAUTION: Failure to follow

More information

Installation Instructions

Installation Instructions Installation Instructions AMP RESEARCH Power Step by Bestop Automatic Retracting Running Board Vehicle Application Nissan Titan King Cab 2004 and newer (5 ft.) Part Number: 75106-01 Nissan Titan Crew Cab

More information

ELECTRONIC FIREPLACE DAMPER

ELECTRONIC FIREPLACE DAMPER ELECTRONIC FIREPLACE DAMPER Model: FSE Low Profile Series The Flue Sentinel Electronic Fireplace Damper is designed to increase the comfort and energy efficiency of residential homes with gas-fired fireplaces.

More information

FUSE PANEL Technical Practice FDP /10 GMT NEBS Level 3 Certified

FUSE PANEL Technical Practice FDP /10 GMT NEBS Level 3 Certified 0521-03A May 2006 FUSE PANEL Technical Practice FDP 1010 10/10 GMT NEBS Level 3 Certified FEATURES 2 isolated groups (busses) of 10 GMT fuses in each (15Amps/GMT position) Polarity insensitive (+/-24 or

More information

Sport Sway Bar Kit C-10 Truck

Sport Sway Bar Kit C-10 Truck Sport Sway Bar Kit 22108 67-72 C-10 Truck Thank you for your purchase from our new line of Chevy parts. Please call us at 877-4NO - ROLL if you have any questions regarding the service or installation

More information

BC Brake Caliper. (i) MEX (55) QRO (442) MTY (81) DIST. AUTORIZADO

BC Brake Caliper. (i) MEX (55) QRO (442) MTY (81) DIST. AUTORIZADO MEX (55) 5 6 QRO (44) 95 7 60 MTY () 54 0 BC Brake Caliper (i) FORM NO. L-0066-B-040 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this

More information

INSTALLATION MANUAL Models &

INSTALLATION MANUAL Models & VAN SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL Models 2275-3-01 & 2277-3-01 Weather Guard / Knaack 800-456-7865 Toll Free 420 E. Terra Cotta Ave 800-334-2981 Fax Crystal Lake, IL 60014 USA Knaack.OrderEntry@wernerco.com

More information

Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual. Lift-Rite Hand Pallet Trucks Model SS45

Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual. Lift-Rite Hand Pallet Trucks Model SS45 Owner s Manual, Operating Instructions Manual, and Replacement Parts Manual Lift-Rite Hand Pallet Trucks Model SS45 This publication, 1188027A, applies to the Lift-Rite Hand Pallet Truck, Model SS45 and

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS REV 3 05/13/2016 PART NO. 911000T 911000PS 915000T 915000PS PRODUCT DESCRIPTION: Sport Bar 2.0, Full size Textured Black Sport Bar 2.0, Full size Polished Stainless Steel Tubes Sport Bar 2.0, Mid size

More information

JK 8-Lug Front Full Float Kit

JK 8-Lug Front Full Float Kit 1 Kit #3034411 w/ Performance Rotors Kit #3034410 w/ Performance Slotted Rotors Kit #3034412 w/ Big Brake Kit Kit #3034413 w/ Big Brake Kit and Slotted Rotors JK 8-Lug Front Full Float Kit www.teraflex.com

More information

Utility Jack Model Number: HD HD HD

Utility Jack Model Number: HD HD HD Utility Jack Model Number: 74407 74407HD 74410 74410HD 74413 74413HD 74412 74415 70429 Rolled Acme Thread and Anti-Friction thrust Bearings High Strength Tubing This Instruction Sheet contains IMPORTANT

More information

Double Scull Car Rack User s Manual

Double Scull Car Rack User s Manual Page 1 Double Scull Car Rack User s Manual Step 1: Attach your double scull car rack to vehicle roof racks We recommend lining up your double scull rack with the towing hooks located underneath your car

More information

Deluxe ASA Halogen Spot/Flood Light

Deluxe ASA Halogen Spot/Flood Light Installation & Operation Instructions Deluxe ASA Halogen Spot/Flood Light 405610-3 To avoid the risk of accidents or damage to this product, it is essential to read these instructions thoroughly before

More information

Premium Supply. Tilt Deck. Models PCK-TD PCK-PTD CTD-310-K. Operator s Manual and Installation Instructions

Premium Supply. Tilt Deck. Models PCK-TD PCK-PTD CTD-310-K. Operator s Manual and Installation Instructions Tilt Deck Models PCK-TD PCK-PTD CTD-310-K Operator s Manual and Installation Instructions Premium Supply 2038 West Interstate 30 866-934-0777 Proud members of: and April 20, 2018 Table of Contents Introduction...

More information

CRD600 Automatic Fitting Inserter

CRD600 Automatic Fitting Inserter CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.3 LAST EDITED 12.07.2018 cleanroomdevices.com 1 Table of Contents Title Page.. 1 Table of Contents. 2 1.0 General Product & Safety Information...3

More information

CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"

CLEAN ROOM DEVICES, LLC WHERE TUBING AND FITTINGS COME TOGETHER CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD600 Automatic Fitting Inserter OPERATIONS MANUAL VERSION 2.1 LAST EDITED 7.25.14 DOCUMENT NUMBER 001 cleanroomdevices.com 1 Table of

More information

INSTALLATION AND MAINTENANCE MANUAL FORM #PM-122 REV A 12/09

INSTALLATION AND MAINTENANCE MANUAL FORM #PM-122 REV A 12/09 HAND CRANK WELDING CABLE REEL: SERIES 100WC COXREELS The technical data and images which appear in this manual are for informational purposes only. NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES

More information

VAN SOLUTIONS FOR THE WAY YOU WORK TM ASSEMBLY AND INSTALLATION INSTRUCTIONS FOR COMPACT SINGLE & DUAL SIDED QUICK CLAMP RACK

VAN SOLUTIONS FOR THE WAY YOU WORK TM ASSEMBLY AND INSTALLATION INSTRUCTIONS FOR COMPACT SINGLE & DUAL SIDED QUICK CLAMP RACK WWW.WEATHERGUARD.COM VAN SOLUTIONS FOR THE WAY YOU WORK TM ASSEMBLY AND INSTALLATION INSTRUCTIONS FOR COMPACT SINGLE & DUAL SIDED QUICK CLAMP RACK MODELS 3-3-03 AND -3-03 Weather Guard / Knaack 800-56-7865

More information

INSTALLATION MANUAL Models &

INSTALLATION MANUAL Models & VAN SOLUTIONS FOR THE WAY YOU WORK INSTALLATION MANUAL Models 2295-3-01 & Weather Guard / Knaack 800-456-7865 Toll Free 420 E. Terra Cotta Ave 800-334-2981 Fax Crystal Lake, IL 60014 USA Knaack.OrderEntry@wernerco.com

More information

THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT.

THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. Series 909 Reduced Pressure Zone Backflow Preventers Sizes: 3 /4" 2" (20 50mm) Installation Service Repair Kits Maintenance No. 1 1 2" shown Patent Number 4,241,752 IMPORTANT: Inquire with governing authorities

More information

Instruction Sheet SRSR SERIES. Rotating Sliding Rail System

Instruction Sheet SRSR SERIES. Rotating Sliding Rail System Instruction Sheet SRSR SERIES Rotating Sliding Rail System THANK YOU Thank you for purchasing the SRSR Series Rotating Sliding Rail System. Please read these instructions thoroughly before assembling this

More information

CSA CERTIFIED Conforms to UL 507

CSA CERTIFIED Conforms to UL 507 Installation tion Instructions Please read and save these instructions! TURBO/MAXX12 Volt All Weather RV Ventilator Fans P/N 00-965001 Deluxe Model 1200T WITH THERMOSTAT P/N 00-965007 Standard Model 3550

More information

CRD400 Fitting Inserter OPERATIONS MANUAL

CRD400 Fitting Inserter OPERATIONS MANUAL CRD400 Fitting Inserter OPERATIONS MANUAL ORIGINAL INSTRUCTIONS VERSION 3.4 LAST EDITED 01.07.2019 www.cleanroomdevices.com 1 Table of Contents Title Page.. 1 Table of Contents... 2 1.0 General Product

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory Application Publications No. S P/N 08V31-SCV-102 2008 ELEMENT AII 36531 Issue Date MAY 2007 PARTS LIST 15 Wire ties 2 Fog lights 4 Wire ties with clip Switch harness

More information

Installation Instructions

Installation Instructions Equipment Required: Installation Instructions Fastener Kit: F Wrenches: 3/4, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers

More information

ActuLink ABS Module - ABS-MOD-400

ActuLink ABS Module - ABS-MOD-400 Installation Instructions ActuLink ABS Module - ABS-MOD-400 For more information on the installation and operation of Tuson s towable ABS system, consult the installation and operations manuals for the

More information

Free Float Air Trap G8

Free Float Air Trap G8 172-65193MA-06 (G8) 24 June 2015 ISO 9001/ ISO 14001 Manufacturer Kakogawa, Japan is approved by LRQA LTD. to ISO 9001/14001 Free Float Air Trap G8 Copyright 2015 by TLV CO., LTD. All rights reserved 1

More information

VAN SOLUTIONS FOR THE WAY YOU WORK TM ASSEMBLY AND INSTALLATION INSTRUCTIONS FOR QUICK CLAMP ACCESSORY CROSS MEMBER

VAN SOLUTIONS FOR THE WAY YOU WORK TM ASSEMBLY AND INSTALLATION INSTRUCTIONS FOR QUICK CLAMP ACCESSORY CROSS MEMBER WWW.WEATHERGUARD.COM VAN SOLUTIONS FOR THE WAY YOU WORK TM ASSEMBLY AND INSTALLATION INSTRUCTIONS FOR QUICK CLAMP ACCESSORY CROSS MEMBER MODELS 5-3-3 AND 33-3-3 Weather Guard / Knaack 8-56-7865 (Toll Free)

More information

AEROMOTIVE Part # Street Rod Fuel Pump System INSTALLATION INSTRUCTIONS

AEROMOTIVE Part # Street Rod Fuel Pump System INSTALLATION INSTRUCTIONS AEROMOTIVE Part # 17201 Street Rod Fuel Pump System INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend

More information

Dual Flow Manifold Systems Instruction Manual

Dual Flow Manifold Systems Instruction Manual 3M TM Water Filtration Products Dual Flow Manifold Systems Instruction Manual For DF1XX and DF2XX High Flow Series manifolds and water filtration systems Installer: Please leave this manual with owner/operator.

More information

DeZURIK 2 20" BOS BUTTERFLY VALVES

DeZURIK 2 20 BOS BUTTERFLY VALVES 2 20" BOS BUTTERFLY VALVES Instruction D10459 October 2013 2-20 BOS Butterfly Valves Instructions These instructions provide information about BOS Butterfly Valves. They are for use by personnel who are

More information

FIGURE 310A & 311A 3-PIECE BALL VALVE

FIGURE 310A & 311A 3-PIECE BALL VALVE INTRODUCTION This instruction manual includes installation, operation and maintenance information for the figure 310A, 310ASW, 311A, and 311ASW 3-piece 1000CWP, threaded end (NPT) or socket weld end (SW)

More information

Installation Manual. D3600- Series Duplex Grinder Systems. Contents

Installation Manual. D3600- Series Duplex Grinder Systems. Contents Installation Manual 7353000E D3600- Series Duplex Grinder Systems Features: 36 Diameter Fiberglass Tank Available in 48, 60, 72, 84, and 96 heights LSG Single or LSGX 2 Stage 2HP Grinder Pumps Factory

More information

CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER"

CLEAN ROOM DEVICES, LLC WHERE TUBING AND FITTINGS COME TOGETHER CLEAN ROOM DEVICES, LLC "WHERE TUBING AND FITTINGS COME TOGETHER" CRD600AF Automatic Fitting Inserter With Auto Feed OPERATIONS MANUAL (Shown with optional alcohol dispenser) 1 VERSION 1.1 LAST EDITED

More information

INSTALLATION GUIDE DIRECT-REPLACEMENT

INSTALLATION GUIDE DIRECT-REPLACEMENT DIRECT-REPLACEMENT INSTALLATION GUIDE TACOMA (05+) 880-06-376-2.5 Factory Series Coil-Over Reservoir - Adjustable 880-06-418-2.5 Factory Series Coil-Over Reservoir - Adjustable 880-02-376-2.5 Factory Series

More information

Model GD-70D4A-XX Supplement to the GD-70D Operator s Manual

Model GD-70D4A-XX Supplement to the GD-70D Operator s Manual Model GD-70D4A-XX Supplement to the GD-70D Operator s Manual Part Number: 71-0192RK Revision: A Released: 1/27/17 www.rkiinstruments.com WARNING Read and understand this instruction manual before operating

More information

DISPLACEMENT: The maximum displacement that may be achieved in the Ski Superstock Class is 1500 cc.

DISPLACEMENT: The maximum displacement that may be achieved in the Ski Superstock Class is 1500 cc. SKSS.1 SUPERSTOCK CLASS COMPETITION Competitors in this class are allowed modifications to gain maximum machine and engine performance while restricting the build costs by prohibiting aftermarket hulls

More information