Loctite Air Filtration System Part Number EQUIPMENT. Operation Manual

Size: px

Start display at page:

Download "Loctite Air Filtration System Part Number EQUIPMENT. Operation Manual"

Claud Nicholson
5 years ago
Views:

1 Loctite Air Filtration System Part Number EQUIPMENT Operation Manual

2 Contents Page No. 1 PLEASE OBSERVE THE FOLLOWING EMPHASIZED SECTIONS FOR YOUR SAFETY UNPACKING AND INSPECTION ITEMS SUPPLIED FEATURES USAGE DESCRIPTION OPERATING ELEMENTS AND CONSTRUCTION THEORY OF OPERATION FILTERING METHOD THERMAL OVERLOAD PROTECTION TECHNICAL DATA INSTALLATION INSTALLATION AND CONNECTION MAINTENANCE AND CLEANING FILTER UNIT FILTER REPLACEMENT TROUBLESHOOTING SPARE PARTS AND ACCESSORIES REPLACEMENT FILTERS ACCESSORIES - EXHAUST ARM KIT ACCESSORIES - EXHAUST CABINET KIT WARRANTY

3 1. Please Observe the Following 1.1 Emphasized Sections Warning! Refers to safety regulations and required safety measures that protect the operator or other persons from injury or danger to life. Caution! Emphasizes what must be done or avoided so that the Unit or other property is not damaged. Notice: Gives recommendations for better handling of the Unit during operation or adjustment as well as for service activities. 1.2 For Your Safety For safe and successful operation of the Unit, read these instructions completely. If the instructions are not observed, the manufacturer can assume no responsibility. Be sure to retain this manual for future reference. Do not use the Unit to extract easily flammable or explosive gases. Do not use the Unit to extract corrosive substances. Do not expose the connecting cable to heat, oil, or sharp edges. Make sure the Unit stands stable and secure. Use only original equipment filters. Do not operate the Unit without filter inserts. Contaminants in the extracted air will damage the blower. Always disconnect the power supply before servicing the Unit. Never cover intake or exhaust openings. This system is equipped with automatic reset overload protection (thermal switch or overload relay), which may cause the Unit to restart automatically. See page 4. Observe general safety regulations for the handling of chemicals such as Loctite adhesives and sealants. Observe the manufacturer s instructions as stated in the Material Safety Data Sheet (MSDS). While under warranty, the Unit may be repaired only by an authorized Loctite service representative. 1.3 Unpacking and Inspection Carefully unpack the Loctite Air Filtration System and examine the items contained in the carton. Inspect the Unit for any damage that might have occurred in transit. If such damage has occurred, notify the carrier immediately. Claims for damage must be made by the consignee to the carrier and should be reported to the manufacturer. 1

4 1. Please Observe the Following (continued) 1.4 Items supplied Air Filtration System Prefilter Carbon Filter - 20 lbs., with 1 carbon tray mat Afterfilter Operating Manual 1.5 Features Unit on/off foot switch Explosion-proof motor Thermal overload protection Filter status indicator (differential gauge) High airflow rates Runs very quietly Large filter size extends filter lifespan Multi-stage filtration Connects to 4" and 2.5" dia. hoses Compact size, Unit fits under workbench UL, CSA Certified 1.6 Usage This model is ideal for providing fume extraction at the workplace. It operates very quietly and is recommended for the connection of 1 to 4 exhaust arms or two exhaust cabinets. For low operating costs the Unit features a large filter of 14" x 18", which reduces the frequency of filter replacements. A differential pressure gauge indicates the filter status. 2. Description 2.1 Operating Elements and Construction Main Switch (Foot Switch) A foot switch is used to turn the filter unit on and off. This switch needs to be located as far away from the filter unit as possible. Filter Monitor Differential Pressure Gauge (Filter Monitor) The differential pressure gauge monitors the filter condition by measuring the pressure difference (pressure drop) between upstream and downstream of the particulate filters. As filter saturation increases, the pressure drop increases and the airflow decreases. When the pressure drop reaches a predefined level, filter maintenance should be performed. This is generally the point where airflow is inadequate. Gas Phase Monitor There is no filter monitoring system for the gas phase filter installed in this model. The monitoring of the exhaust air according to Indoor Air Quality Standards remains the responsibility of the operator. Please refer to Gas Phase Filter Monitoring. 2

5 2. Description (continued) Air Filtration System (2) 4" dia. Inlets (2) x 2.5" dia. Inlets 2" Pleated Filter or optional HEPA Filter LOCTITE Air Filtration System 20 lbs. (9 kg) Carbon Tray White Mat Afterfilter Mat Filter Monitor Power Switch 2.2 Theory of Operations The Loctite Air Filtration System removes airborne contaminate by extracting air close to the source of particulate and vapors. The air is collected by a funnel-shaped nozzle or hood and routed, through hose or duct, to the filter unit. Filtering is accomplished in stages: The pleated prefilter removes coarse particles such as dust. Optional HEPA filter available. The activated carbon filter absorbs gases and odors. The afterfilter mat removes dust particles from the gas phase filter media. After the air is filtered it is directed out the exhaust vent at bottom of the Unit. 2.3 Filtering Method The contaminated air is drawn into the filter unit and passes through a combination of filters. Filtration is accomplished in three stages: The pleated prefilter removes coarse particles such as dust. The gas phase filter absorbs gases and odors. The efficiency and lifetime of the gas phase filter depends on a range of variables, which are, among others, flow-rate, temperature, humidity, concentration levels, etc. An afterfilter, located downstream, removes dust particles from the gas phase filter media. For the removal of gases, which exceed OSHA, established TEL-values upstream of the filter unit, the efficiency and lifespan of the gas phase filter need to be established and monitored. 3

6 2. Description (continued) Gas Phase Filter Monitoring Loctite recommends two different ways for maintaining and monitoring gas phase filters, depending on the application and purpose of the gas phase filter: A) For the removal of odors as a nuisance only and for gases not exceeding the TEL-values established by OSHA upstream (at air inlet): Replace the filter media in any of the following cases: As soon as odors becomes noticeable. At least every 6 months, as most gas phase filter media achieve saturation by adsorbing moisture from ambient air. B) For toxic gases which do exceed TEL-values established by OSHA upstream of the filter unit (at air inlet): Establish the lifespan of the filter media depending on the local site conditions. Monitor the lifespan of the filter media. Replace the filter media as soon as the lifetime of the filter media is reached. The lifetime of the gas phase filter can be determined by initial periodical testing of the exhausted air for contamination. The lifetime is measured in operating hours until breakthrough occurs. An optional way is a laboratory evaluation of the spent gas phase filter media after a certain time period. For further information, contact our customer service department. 2.4 Thermal Overload Protection The filter unit motor is equipped with factory installed automatic thermal overload protection. In case of overheating, the motor is automatically turned off, preventing premature burnout of the motor windings. Caution! Motor may start up automatically the automatic thermal overload protection will turn the motor on automatically as soon as the motors cools down again. Overheating of the motor can result from the following: Saturated filter An accumulation of contaminates clogs the filter and the air volume decreases. This results in insufficient air available for cooling, and therefore overheating results. SOLUTION: Change filter inserts regularly! Blocked Flow Insufficient air volume due to other reasons, such as a bent connection hose or foreign matter obstructing the airflow. SOLUTION: Straighten hoses and check air passage for foreign material. 4

7 3. Technical Data Air inlet ports (2) 4" dia. and (2) 2.5" dia. Fan capacity 700 cfm / 1165 m 3 /h System capacity 200 cfm / 335 m 3 /h Max. static pressure 3.5" WG / 875 Pa Power supply 115 V, 1 phase, 60Hz Motor rating 0.75 HP / 560 watts Power consumption 10 Amps Noise level, approx. 60 dba Certifications UL, CSA Dimensions (W x D x H) 15.5" (395 mm) x 19.5" (495 mm) x 27" (685 mm) Weight (approx.) 100 lbs. / 45 kg 4. Installation 4.1 Installation and Connection In order to properly install the Air Filtration System, the following procedure should be followed: Open the Unit s top cover by releasing the four latches and removing the lid. Remove pleated prefilter. Remove carbon filter tray. Install the white mat on the bottom of the metal carbon filter tray. Fill the carbon tray with activated carbon. The activated carbon is supplied in a separate bag. Check to insure afterfilter mat is properly seated. Install carbon tray into Unit Install pleated prefilter. Install the Unit s top cover and secure the four latches. Attach a flexible hose to the air inlet port(s), on the lid, using hose clamps. If the sum of the ports are not being used, keep them closed with a blind cover. Attach the other end of the hose to a suction nozzle, exhaust arm, or matching duct. Assure that all duct and hose connections are airtight. Leakage will result in decreased performance. External on/off foot switch: Connect the series plug, which is attached to the power cord coming from the foot switch, to wall outlet. Plug the filter systems power cord (3-prong plug) into the receptacle of the series plug. The Loctite Air Filtration System is ready to be turned on. 5

8 5. Maintenance and Cleaning 5.1 Filter Unit The filter unit does not need any special maintenance, except for filter replacement as described below. The installed motor is a brushless type and made for continuous use. To protect the motor in an overload situation, the motor is equipped with a thermal overload protection as described on page Filter Replacement As the filter insert becomes increasingly saturated, the exhaust capacity of the Unit decreases. When the pressure gauge reaches a factory preset level (red mark), the airflow approaches a minimum and filters should be replaced. Filter Replacement Procedure: Caution! Fire Hazard: The gas phase filter media may be saturated with flammable substance. Do not handle or replace filter while smoking or in close distance to any open flame. To replace the filters: Turn the Unit off and disconnect from main power source. Open the Unit's top cover by releasing the four latches and removing the lid. Remove pleated prefilter (or optional HEPA filter). Remove activated carbon tray. Empty the filter tray by pouring the saturated filter media into a waste container. Dispose of carbon tray filter mat. Caution! Used filter media may contain toxic or flammable substances. Observe relevant codes for safety and local hazard s material disposal. Install the white mat on the bottom of the metal carbon filter tray. Fill the carbon tray with activated carbon. The activated carbon is supplied in a separate bag. Note: The bulk carbon contains a certain amount of dust which is created during transport and handling by the pellets rubbing against each other. Therefore, you will see dust escaping during the refilling process. Please make sure the operator wears the appropriate protective mask. The Loctite Air Filtration System is equipped with an afterfilter mat. We recommend leaving the old afterfilter mat in place after the carbon has been replaced and replace it only after the Unit has been in operation for 10 to 15 minutes. After that time, or if you notice a substantial reduction in the airflow, you should change the afterfilter. This insures that the carbon dust from the refill will be collected in the old filter and not lower the airflow of the new filter set. 6

9 5. Maintenance and Cleaning (continued) Install carbon tray into Unit. Install pleated prefilter. Install the Unit s top cover and secure the four latches. Attach a flexible hose to the air inlet port(s) on the lid. If the some of the ports are not being used, keep them closed with a blind cover. Attach the other end of the hose to a suction nozzle, exhaust arm, or matching duct. Assure that all duct and hose connections are airtight. Leakage will result in decreased performance. External on/off foot switch: Connect the series plug, which is attached to the power cord coming from the foot switch, to wall outlet. Plug the filter systems power cord (3-prong plug) into the receptacle of the series plug. The Loctite Air Filtration System is to be turned on. Do not operate the filter system without filters installed. This may overload the electric motor. Caution! Do not clean the filters. Cleaning the filters by batting or using compressed air will destroy the filter. Always use a new replacement filter! 6. Troubleshooting Type of Malfunction Possible Causes Solutions Unit does not power when switched on. Motor suddenly turns off. Not plugged into proper power receptacle. The motor is overheating and the thermal overload protection circuit has automatically turned the motor off. Overheating of the motor can result from the following: 1. Saturated filter 2. Blocked flow For the the power requirements are 230 Volt, 2 amp. Change filter inserts regularly! Straighten hoses and check air passage for foreign material. 7

10 7. Spare Parts and Accessories 7.1 Replacement Filters & Optional Items Filter, Pleated, 14'' x 18'' x 2'', 60%, 6/Set Filter, HEPA Mini-Pleat, 14'' x 18'' x 2'', 99.97% at 0.3 micron, 1 ea. (Optional) Filter, Carbon Refill Package, 20 lbs., with 1 filter mat Afterfilter Mat, White, 5/set Metal Tray with Carbon Refill Omni-Flex Damper Omni-Flex Segment Enclosure Cover Latches, 4 Pack " Vent Plug, 2 Pack " Vent Cap, 2 Pack 7.2 Accessories Exhaust Arm Kit Omni-Flex Exhaust Arm, ESD, 2.5" dia., 24" long reach, includes rectangular nozzle, universal mounting plate, connection hose and wall mounting kit Connection Hose, 2.5'' diameter, 8' long, with hose clamps Mounting Kit, consists of mounting angle and C-clamps 7.3 Accessories Exhaust Cabinet Kit Exhaust Cabinet, 30'' x 20'' x 20'', painted with clear Lexan cover Connection Hose, 4'' dia., 12.5' long, with hose clamps 8

11 8. Warranty Henkel Loctite expressly warrants that all products referred to in this Instruction Manual for Loctite Air Filtration System (hereafter called "Products"), shall be free from defects in materials and workmanship. Liability for Henkel Loctite shall be limited, at its option, to replacing those Products which are shown to be defective in either materials or workmanship or to credit the purchaser the amount of the purchase price therefor (plus freight and insurance charges paid therefor by the user). The purchaser s sole and exclusive remedy for breach of warranty shall be such replacement or credit. A claim of defect in materials or workmanship in any Products shall be allowed only when it is submitted in writing within one month after discovery of the defect or after the time the defect should reasonably have been discovered and in any event, within (12) months after the delivery of the Products to the purchaser. This warranty does not apply to perishable items, such as fuses, filters, lights, ect. No such claim shall be allowed in respect of products which have been neglected or improperly stored, transported, handled, installed, connected, operated, used, or maintained. In the event of unauthorized modification of the Products including, where products, parts, or attachments for use in connection with the Products are available from Henkel Loctite, the use of products, parts, or attachments which are not manufactured by Henkel Loctite, no claim shall be allowed. No Products shall be returned to Henkel Loctite for any reason without prior written approval from Henkel Loctite. Products shall be returned freight prepaid, in accordance with instructions from Henkel Loctite. NO WARRANTY IS EXTENDED TO ANY EQUIPMENT WHICH HAS BEEN ALTERED, MISUSED, NEGLECTED, OR DAMAGED BY ACCIDENT, OR IF THE SYSTEM USED TO DISPENSE ANY LIQUID MATERIAL OTHER THAN LOCTITE PRODUCTS. EXCEPT FOR THE EXPRESS WARRANTY CONTAINED IN THIS SECTION, HENKEL LOCTITE MAKES NO WARRANTY OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS. ALL WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND OTHER WARRANTIES OF WHATEVER KIND (INCLUDING AGAINST PATENT OR TRADEMARK INFRINGEMENT) ARE HEREBY DISCLAIMED BY HENKEL LOCTITE AND WAIVED BY THE PURCHASER. THIS SECTION SETS FORTH EXCLUSIVELY ALL OF LIABILITY FOR HENKEL LOCTITE TO THE PURCHASER IN CONTRACT, IN TORT OR OTHERWISE IN THE EVENT OF DEFECTIVE PRODUCTS. WITHOUT LIMITATION OF THE FOREGOING, TO THE FULLEST EXTENT POSSIBLE UNDER APPLICABLE LAWS, HENKEL LOCTITE EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER FOR ANY DAMAGES INCURRED DIRECTLY OR INDIRECTLY IN CONNECTION WITH THE SALE OR USE OF, OR OTHERWISE IN CONNECTION WITH THE PRODUCTS, INCLUDING, WITHOUT LIMITATION, LOSS OF PROFITS AND SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER CAUSED BY NEGLIGENCE FROM HENKEL LOCTITE OR OTHERWISE. 9

12 Loctite Industrial Henkel Loctite Corporation 1001 Trout Brook Crossing Rocky Hill, CT Henkel Loctite Automotive Technology Center 2455 Featherstone Road Auburn Hills, Michigan Henkel Loctite Canada Inc Meadowpine Boulevard Mississauga, Ontario L5N 7P2 Henkel Ltda. Brazil Av. Prof. Vernon Krieble, Itapevi São Paulo-Brazil Henkel Mexicana, S.A. de C.V. Calzada de la Viga s/n, Fracc. Los Laureles Loc. Tulpetlac, C.P Ecatepac de Morelos, Edo. de México, México Loctite is a registered trademark of Henkel Loctite Corporation, U.S.A. Copyright Henkel Loctite Corporation. All rights reserved. Data in this operation manual is subject to change without notice. P/N /03

EQUIPMENT. Loctite Bench Top Air Filtration System Plenum Style Part Number Air Filtration System With Arm Part Number

EQUIPMENT. Loctite Bench Top Air Filtration System Plenum Style Part Number Air Filtration System With Arm Part Number EQUIPMENT Operation Manual Loctite Bench Top Air Filtration System Plenum Style Part Number 98278 Loctite Bench Top Air Filtration System With Arm Part Number 98277 Contents Page No. 1 PLEASE OBSERVE THE