ARDINAL EASTMAN. Round Knife Machines CLASS 534, 548, 562 AND 567. Instruction Book and Illustrated Parts List
|
|
- Tamsyn Lang
- 5 years ago
- Views:
Transcription
1 Eastman EASTMAN ARDINAL R Round Knife Machines CLASS 34, 4, 2 AND EASTMAN Instruction Book and Illustrated Parts List Please read completely before attempting to operate your new Cardinal. WARNING This machine is equipped with a very sharp knife. Keep hands, arms, and hair away from the knife area at all times. Misuse of this machine or failure to follow all safety instructions on this machine and in the instruction manual may result in serious personal injuries. Form C-103 Technical Support: Eastman Over a Century of Cutting Expertise Washington St., Buffalo, N.Y U.S.A. (1)-2200 Fax (1)-40 or (1)-20 Manufacturers of Eastman Cutting and Spreading Machines customerservice@eastmancuts.com
2 Eastman Table of Contents Safety Information...3 General Safety Precautions...3 Safety And Indemnification...3 Operation...4 Maintenance...4 Knife Replacement...4 To Adjust Emery Wheels... Replacement Knives... Lubrication Maintenance... Cardinal Familiarization... Guard Assembly... Standard Assembly, 4H, 2H And H... Standard Assembly X and X...10 Sharpener Assembly H and 34BK4H - Single Phase Motors H and 34BK4H - Three Phase Motors...1 4BKH and 4CCH - Single Phase Motors BKH and 4CCH - Three Phase Motors H - Single Phase Motors H - Three Phase Motors H - Single Phase Motors H - Three Phase Motors X - Single Phase Motors X - Three Phase Motors X and 2BKX - Single Phase Motors X and 2BKX - Three Phase Motors...3 X - Single Phase Motors...40 X - Three Phase Motors...42 X and BKX - Single Phase Motors...44 X and BKX - Three Phase Motor /4 BK And Carpet Cutter Assembly...4 2/ BK Assembly...4 Slitter And CC Base Plate Assembly 4H and H...0 Slitter Base Plate Assembly X And X...1 Moistening Attachment With Guard... 2 Moistening Attachment With Guard 1/2"....4 RK Push Swivel Handle Assembly 3"... Stationary Baseplate 4-2H Slitter... Stationary Baseplate 2/BK Slitter... Wiring Diagrams... Electrical Connections... Technical Data...0 IMPORTANT The purchaser must instruct all operators on the proper use of this equipment. All standard industrial safety measures and equipment should be provided to protect the operator. Operators must be cautioned that improper or careless use of this equipment may cause personal injury. If you do not have qualified operators to instruct new persons, contact your EASTMAN sales representative or EASTMAN factory direct. Electrical connections and servicing to this equipment should be made by a qualified electrician who is familiar with applicable codes and regulations. Disconnect this equipment from electrical power source before proceeding with any disassembly for adjustment or repair. 2 Form C-103
3 Safety Information Throughout this manual, safety information is presented by the use of the terms WARNING, CAUTION, ELECTRI- CAL HAZARD, and NOTE. These terms have the follow- WARNING A warning contains critical information regarding potential safety hazards that can occur during proper use or misuse of the machine. Failure to follow these procedures may result in serious personal injury to the user. CAUTION A caution contains instructions for the use or maintenance of the machine. Failure to follow these procedures may result in damage to the machine. Safety and Indemnification During the life of the machine, the purchaser agrees to provide to all machine users (including its own employees and independent contractors) all relevant safety information, including warning labels and instruction manuals. The purchaser also agrees to maintain the safety features and working condition of the machine, and to adequately train all users in the safe use and maintenance of the machine. The purchaser agrees to defend, protect, indemnify, and hold Eastman Machine Company and its subsidiaries harmless from and against all claims, losses, expenses, damages, and liabilities to the extent that they have been caused by the purchaser s failure to comply with the terms and instructions of this manual. ELECTRICAL HAZARD An electrical hazard calls attention to a procedure, practice, or the like, which, if not correctly performed or adhered to, could result in personal injury. Do not proceed beyond an Electrical Hazard. General Safety Precautions WARNING This machine is equipped with very sharp and dangerous tools. Keep hands, arms, and hair away from the cutting area and drive system at all times. Safety gloves, glasses, and appropriate clothing may prevent serious personal injuries. Disconnect the power supply to the machine when it is not in use or during routine maintenance, including cleaning and lubrication. Do not modify this machine or disable safety features. Unauthorized modification may result in serious personal injuries to the user. Electrical connections to this machine must be made by a qualified electrician familiar with applicable codes and regulations. Safety labels must be kept clean and legible at all times. Call the Eastman Machine factory to order replacement labels. The purchaser must instruct all operators in the proper use of the machine according to the instructions in this manual. This training must include instruction on the potential safety hazards arising from the use or misuse of the machine. In addition to such training, the purchaser should provide written work instructions as necessary to ensure correct use of the machine for specific cutting and spreading applications. Eastman Over a Century of Cutting Expertise Form C-103 3
4 Eastman OPERATION Turn the switch to the on position; if cutter does not start immediately, return the switch to the off position. Check the line output and be sure that the unit is plugged in properly and is making full contact, then repeat procedure. Do not attempt to start this unit while it is in the material being cut. E F MAINTENANCE CAUTION Before performing any of the following procedures make sure that the attachment is disconnected from this system. D K L C Knife Motor WARNING This machine is equipped with a sharp knife. Keep hands away from knife area at all times. Use handle and control lever when operating or handling the machine. Knife guard should be raised only enough to clear the material being cut. When not in use, knife guard should be set at the lowest position. DO NOT OPERATE THIS MACHINE WITH KNIFE GUARD REMOVED. SMALL PIN PART NO. 1C Maintenance Procedures 1. Be sure that the rollers of the base plate are kept free of debris. 2. Be sure that the terminal pins on the terminal block are kept in good condition to make full contact with the female receptacle. 3. Inspect the operating switch periodically to make sure that it is making full contact when in the "ON" position. 4. When replacing the knife on this cutting unit, be sure that any cutting debris between the knife and the standard is cleaned out.. If the cutting unit seems to lag while not cutting, the knife should be removed and the unit should be run without the knife to see if the machine has been over-greased or is there is an obstruction somewhere. Knife Sharpening Take the machine out of the material to be cut. Switch power to ON position (use CAUTION when sharpening blade). To obtain a fine, keen edge on the blade, press and hold sharpener trigger lightly, the sharpening stones will contact the blade. Press and hold trigger with constant pressure for 10 seconds, then release. Repeat process as necessary. Knife Replacement SPANNER WRENCH PART NO. BLADE DIA. C1-4"," C1-1/4",", 1/2" WARNING This knife is very sharp. Failure to follow proper precautions when handling may result in serious injury. Discard used knife with care! Loosen thumb screw "E" and swing guard "F" to outward position as shown on dotted lines. Turn the knife so the small hole lines up with hole "G" in the standard. Insert the small pin that is with the supplies in hole "G." Remove the lock nut that retains the blade with the special spanner wrench. When installing a new knife, be sure the name "Eastman Machine Company" is facing outward, and that the knife seats on the gear. Install knife lock nut and be sure that throat plate is adjusted as outlined. 4 Form C-103
5 To Adjust the Throat Plate It is very important that the edge of the knife be as close as possible without touching to the forward position in the slot on the throat plate. The slot in the throat plate "J" should straddle the blade and screws "H" can be loosened and re-tightened to accomplish this adjustment. D To Adjust Emery Wheels As the Emery Wheels wear away and become farther apart, they must be adjusted. Adjust Emery Wheels from both sides to assure proper centering of the wheels over the knife. Proceed as follows: 1. Loosen slotted head screws "K." 2. With fingers, turn adjusting bushings "L" until Emery Wheels are as close together as possible without touching, and are centered over the knife. Both wheels should grind at the same time when pressed lightly against the knife and there should be no more than 1/32"-inch clearance between the two Emery Wheels. 3. Tighten slotted head screws "K". To Replace Emery Wheels 1. With front of machine facing serviceman, guard rod in down safe position, remove right hand grinding wheel and arm by loosening screw "D" and sliding arm off shaft. 2. Remove slotted head screw "C" and replace grinding wheel with spindle in right hand arm. 3. No need to remove left hand arm from machine. Remove slotted head screw "C" from left hand arm and replace grinding wheel with spindle. 4. Re-assemble right hand arm to shaft and adjust wheels to knife as covered above. CAUTION Do not use sewing machine oil or detergent oil. It is entirely too light for cutting machine lubrication. For best results use specially compounded Eastman Oil. Do not oil base plate rollers. F E G Lubrication Maintenance TWICE A DAY Oil Emery Wheel Spindles at location "C." DO NOT USE AN EXCESS AMOUNT OF OIL H C B A ONCE A DAY Lubricate gears, screw grease cup "A" down one-half turn. Refill cup, as required with Eastman Gear Lubricant, special formula: (242C2) We recommend our Eastman Gear Lubricant special formula (242C2) for gears and Eastman Lubriko grease (242C2-2) for knife gear ball bearings. Do not use Eastman Gear Lubricant for ball bearings, or Eastman Lubriko grease for gears. J K L Knife Diameter 4-1/4-1/2 Form C-103 Carbon Steel 0C1-1 0C C C C1-/100 1 High Speed Steel 0C1-2 0C C C C1-/100 2 Replacement Knives High Speed Steel Grooved 0C1-0C C1-1 0C1-3 0C1-/100 High Speed Steel Teflon Coated 0C1-0C C1-1 0C1-3 0C1-/100 Carbon Slotted C1-0 1 Dbl-Bevel Hi-Speed C1-14 Eastman Over a Century of Cutting Expertise
6 Eastman Cardinal Familiarization Guard Assembly See Page EASTMAN Motor Assembly See Pages 1-4 Sharpener Assembly See Pages Standard Assembly See Pages - Base Plate Assembly See Pages 14-1 Form C-103
7 Guard Assembly (A) C1-3 (34 4H and 34BK4H) (B) C1-4 (4BKH, 4CCH and 4 2H) (C) C1- (4 H) (D) C1- (2 X and X) (E) C1- (2 X and X) 1 4C2-3 Spline Nut 1 2A 2C-1 Guard Rod Holder Bracket 1 2B 2C-0 Guard Rod Holder Bracket 1 2C 2C-0 Guard Rod Holder Bracket 1 2D 2C- Guard Rod Holder Bracket 1 2E 2C- Guard Rod Holder Bracket 1 3A 33C4-23 Guard Rod Holder 1 3B 33C4-23 Guard Rod Holder 1 3C 33C4-24 Guard Rod Holder 1 3D 33C4-2 Guard Rod Holder 1 3E 33C4-2 Guard Rod Holder C4-3 Lock Screw 1 1C1-3 Pin 1 C1-103 Washer 1 A C2- Guard Rod 4" Knife 1 B C2- Rod Knife Guard - 1 C C2- Rod Knife Guard - 1 D C2-3 Rod Knife Guard X 1 E C2-0 Rod Knife Guard X 1 20C-2 Guard Rod Screw 1 300C- Screw,Rd.Hd.#-32 X / Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. Eastman Over a Century of Cutting Expertise Form C-103
8 Eastman Standard Assembly, 4H, 2H and H (A) 34 4H (B) 4 2H (C) 4 H 1A 31C1- Operating Handle 1 1B 31C1-3 Operating Handle 1 1C 31C1-3 Operating Handle 1 2A 4C1- Operating Handle Lock Nut 1 2B 4C1-0 Operating Handle Lock Nut 1 2C 4C1-0 Operating Handle Lock Nut 1 3B C1- Switch Lever 1 3C C1- Switch Lever 1 4B 302C-2 Screw, Flat, Hd #-32 x /1 1 4C 302C-2 Screw, Flat, Hd #-32 x /1 1 1C1-4 Standard Pin 2 4C4 Side Guide Nut 1 2C4-20 Grease Cup 1 A 3C4-4 Gear Cover 4H 1 B 3C4-3 Gear Cover 2H 1 C 3C4-4 Gear Cover H 1 300C- Screw, Rd. Hd. #-32 x / 2 10B C2- Switch Lever Knob 1 10C C2- Switch Lever Knob 1 A C1- Standard Complete 4H 1 B C1- Standard Complete 2H 1 C C1-101 Standard Complete H 1 A C- Knife Gear Shim 4H 1 B C- Knife Gear Shim 2H H 1 C C- Knife Gear Shim 2H H 1 A 2C4- Side Guard 4" 1 B 2C4- Side Guard -1/4" 1 C 2C4-140 Side Guard " C Side Guard Screw 1 1A 21C1-3 Gear Set and Bearing 4H/H 1 1B 21C1-21 Gear Set and Bearing 2H/H 1 1C 21C1-21 Gear Set and Bearing 2H/H 1 1A 0C- Knife Gear Bearing 4H/H 1 1B 0C-33 Knife Gear Bearing 2H/H 1 1C 0C-33 Knife Gear Bearing 2H/H 1 1A 20C4-2 Bearing Lock Screw 4"/" 1 1B 20C4-2 Bearing Lock Screw -1/4"/" 1 1C 20C4-2 Bearing Lock Screw -1/4"/" 1 1A 4C1-4 Bearing Locking Nut 4"/" 1 1B 4C1-3 Bearing Locking Nut -1/4"/" 1 1C 4C1-3 Bearing Locking Nut -1/4"/" 1 1A 4C1-1 Knife Lock Nut 4"/" 1 1B 4C1-2 Knife Lock Nut -1/4" " 1 1C 4C1-2 Knife Lock Nut -1/4" " 1 20A 21C1-2 Bearing Seal 4"/" 1 20B 21C1-1 Bearing Seal -1/4" " 1 20C 21C1-1 Bearing Seal -1/4" " 1 Item numbers are for reference only. Please Specify PART NUMBER when ordering replacement parts. Form C-103
9 Part of C1-4H/H C1-14 2H/H For Knife Options See Page Eastman Over a Century of Cutting Expertise Form C-103
10 Eastman Standard Assembly X and X (A) 2 X and X (B) 2 X and X 1 31C1-3 Operating Handle 1 2 4C1-1 Operating Handle Lock Nut 1 3 2C-0 Handle Adapter 1 4 1C1-4 Standard Pin 2 2C4-20 Grease Cup 1 A C1-4 Standard Complete X 1 B C1-3 Standard Complete X 1 A 2C4-3 Side Knife Guard X 1 B 2C4- Side Knife Guard X 1 20C-1 Screw, Thumb 1 302C-2 Screw,Flt.Hd.#4-3 X 1/ C4-2 Gear Cover X/X 1 A 20C4-2 Inter Screw Lock 1 B 20C4-3 Inter Screw Lock 1 4C1-103 Locknut Inter Gear 1 C-14 Gear Intermediate C-1 Screw,Skt.Hd.#4-40 X 1/4 1 0C- Ball Bearing C1-2 Gearing/Bearing Set X/X 1 1 C2-2 Gear Knife X/X 1 1 0C-33 Ball Bearing C4-30 Screw Lock Knife Bearing C1-3 Locknut Knife Gear Bearing C1-2 Knife Locknut Item numbers are for reference only. Please Specify PART NUMBER when ordering replacement parts. 10 Form C-103
11 Part of C1-1 X/X For Knife Options See Page Eastman Over a Century of Cutting Expertise Form C-103
12 Eastman Sharpener Assembly (A) 3C " Round Knife (B) 1C1-2 - " Round Knife (C) 1C /4" Round Knife (D) 1C1-2 - " Round Knife (E) 3C /2" Round Knife 1 1C1-1 Pin,Cotter 1/1 X 1/2 2 2 C1- Link Sharp Contact 1 3 C2-1 Lever Sharp C-2 Screw, Sharpener Arm Pivot 1 34C1-20 Spring Tension 1 30C-3 Screw, Skt, Set #-32 X 3/ 1 4C3- Block Sharpener Arm 34 1 A 4C3-22 Block Sharpener Arm 4 1 C10-1 Sharpener Shaft 1 302C-3 Screw,Flt.Hd.#-32 X 3/ Sp C1-2 Washer, Flat 2 A 3C1- Sharpener Bracket Assy 4" 1 B 3C1- Sharpener Bracket Assy " 1 C 3C1-10 Sharpener Bracket Assy 1/4 1 D 3C1- Sharpener Bracket Assy " 1 E 3C1- Sharpener Bracket Assy 1/ C-3 Screw, Rd. Hd. #-32 X 3/ 1 E 30C-1 Screw, Skt. Hd. #-32 X 3/ 1 C1-21 Washer, Lock # 1 14A 40C1-3 Arm Emery Wheel RH4 1 14B 40C1-4 Arm Emery Wheel RH& 1/4 1 14C 40C1-4 Arm Emery Wheel RH& 1/4 1 14D 40C1- Arm Emery Wheel RH 1 14E 40C1- Arm Emery Wheel RH 1/ C- Screw, Rd. Hd. #4-40 x /1 2 1A 2C4-10 Knife Guard 4" 1 1B 2C4-11 Knife Guard 1/4" 1 1C 2C4-11 Knife Guard 1/4" 1 1D 2C4- Knife Guard " 1 1E 2C4- Knife Guard " C10-3 Screw,Truss, Hd. #-32x3/ C- Screw, Emery Adjusting Whl C- Arm Sharp Rd. Knife RH C10- Screw, Rd. Hd. #-32 x /1 1 21A 40C1-4 Arm Emery Wheel LH4 1 21B 40C1-4 Arm Emery Wheel LH& 1/4 1 21C 40C1-4 Arm Emery Wheel LH& 1/4 1 21D 40C1-4 Arm Emery Wheel LH 1 21E 40C1-1 Arm Emery Wheel LH 1/ C-3 Screw, Skt, Set #-32 x 3/ C- Arm Sharp Rd. Knife LH C10- Screw, Rd. Hd. #-32 x / C- Screw, Emery Adjusting Whl C10-3 Screw,Truss, Hd. #-32x3/1 1 2A 2C4-10 Knife Guard 4" 1 2B 2C4-11 Knife Guard 1/4" 1 2C 2C4-11 Knife Guard 1/4" 1 2D 2C4- Knife Guard " 1 2E 2C4- Knife Guard " C- Screw, Rd. Hd. #4/40 X / C1-XX See Chart C1- Spindle Grind Whl 1 31 C1-0 Washer,Paper 1 32 C1-2 Washer,Lock,Special C-20 Screw,Oval Hd.#-32 X 3/ C1-XX See Chart 1 Emery Wheel Assembly Options 41C1-0 Grit "/-1/4"/"/x/x Knife 41C Grit 4" Knife 41C1-10 Grit "/-1/4"/"/x/x Knife 41C Grit 4" Knife 41C Grit "/-1/4"/"/x/x Knife 41C Grit 4" Knife Emery Wheel Options 3C1-0 Grit 4" Knife 3C1-0 Grit "/-1/4"/"/x/x Knife 3C1-10 Grit 4" Knife 3C Grit "/-1/4"/"/x/x Knife 3C Grit 4" Knife 3C Grit "/-1/4"/"/x/x Knife Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. Form C-103
13 Eastman Over a Century of Cutting Expertise Form C-103
14 Eastman Base Plate Assembly 4H, 2H and H (A) 0C3- E (4 2H and 4 H) (B) 0C3-203 E (34 4H) (C) 0C3-10 E (2 X and X) 1A C2-44 Filler Plate 1 1B C2-44 Filler Plate 1 1C C2-4 Filler Plate X 1 2A 3C1-4 Plate Flat & Wing 1 2B 3C1- Plate Flat & Wing 1 2C 3C1-1 Plate Flat & Wing C14- Screw,Flt.Hd.#10-24 X 1/ C-2 Screw, Base Plate to Stand C10-3 Screw,Rd.Hd.#-32 X /1 4 C1-3 Throat Plate Washer 4 22C1-2 Roller Plate Front 14 1C-10 Ring Rubber C-1 Washer,Plate Roller 10 41C2 Roller Plate 40 1C1-1 Shell Plate Roller 4 C2-4 Shaft Plt Roller 4 C4- Clip Roller Shaft 2 14 C4- Clip Roller Shaft C10-1 Screw,Flt.Hd.#-32 X 3/ C-XXX See Chart 1 Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts THROAT PLATES C-1 4" and -1/4" Knife C-14 " Knife C-1 " Knife C-1 X and X Knife 14 Form C-103
15 Base Plate and Roller Assembly X and X 0C3-1 E (2 X and X) 1 C2-21 Filler Plate L&X 1 2 C-1 Throat Plate X and X 1 3 3C1-2 Plate Flat & Wing C14-1 Scrw,Binding Hd.#10-24X3/ 2 C1-3 Throat Plate Washer 4 300C10-3 Screw,Rd.Hd.#-32 X /1 4 22C1-4 Roller Plate Front 2 1C-10 Ring Rubber 4 C-1 Washer,Plate Roller 4 10 C2- Shaft Plt Roller 2 41C2- Roller Plate 20 1C1- Shell Plate Roller 2 C4- Clip Roller Shaft C10-1 Screw,Flt.Hd.#-32 X 3/1 1 1C1- Roller Plate Rear C2- Roller Plate 20 1 C-1 Washer,Plate Roller 4 1 1C1- Shell Plate Roller 2 1 1C-10 Ring Rubber 4 20 C2-14 Shaft Plt. Roller Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. Eastman Over a Century of Cutting Expertise Form C-103 1
16 Eastman 34 4H and 34BK4H - Single Phase Motors (A) 1C1-3 - (0V, 0Hz, 1Ph, 2Pole) (B) 1C (0V, 0Hz, 1Ph, 4Pole) (C) 1C1-3 - (220V, 0Hz, 1Ph, 2Pole) (D) 1C1-3 - (220V, 0Hz, 1Ph, 2Pole) 1 4C1- Locknut Front Bearing 1 2 0C-2 Bearing Ball 1 3 0C2-14 Bearing Housing, Front C2-30 Fan, Rotor 1 C3-23 Rotor Shaft 34 4H 1 A 14C4-241 Stator & Band, 00 1 B 14C4-221 Stator & Band, C 14C4-243 Stator & Band, D 14C4-242 Stator & Band, A 0C1-1 Bearing Housing, Rear 34 1 B 2C2- Bearing Housing, Rear 34 1 C 0C1-1 Bearing Housing, Rear 34 1 D 2C2- Bearing Housing, Rear C1- Locknut, Rear Bearing 1 A C2-21 Cut-Out Auto 0CY 2PL 1 B C2-23 Cut-Out Auto 0CY 4PL 1 C C2-22 Cut-Out Auto 0CY 2 PL 1 D C2-21 Cut-Out Auto 0CY 2PL C1-0 Cut-Out Switch C-3 Scr. Round Hd. #-32x3/ 2 C-10 Insulation for Switch 1 0C-4 Bearing Ball 1 14 C1- Washer, Loading Spring C3-3 Screw C-3 Cover, Rear Bearing C10-3 Scr. Round Hd. #-32x3/ 3 1 4C1-10 Nut Bearing Screw 4 1 C1- Gear Set, 4H & H C1- Scr. Flat Hd. #10-32x1&1/ C2-10 Switch Cover C10-4 Scr. Round Hd. #-32x3/ 2 23 C4-20 Switch Insulation C1- Switch, On/Off 1 2 2C-1 Switch Base (Bracket) C10-2 Scr. Round Hd. #-32x1/4 2 2 C4-2 Switch Insulation C10-1 Scr. Binding Hd. #-32x1/4 1 2 C1-32 Washer, Lock # C1-3 Ground Wire Asm. (Grn/Yel) 1 31 C-1 Spacing Washer A/R 32 1C-32 Drive Gear Spacing Sleeve C1-33 Carrying Handle C14-4 Screw, Rd. Hd. #10-24 X 1/2 2 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 1 Form C-103
17 See Page for Complete Parts List Part of C1- Eastman Over a Century of Cutting Expertise Form C-103 1
18 Eastman 34 4H and 34BK4H - Three Phase Motors (A) 1C1-4 - (220V, 0Hz, 3Ph, 2Pole) (B) 1C1-3 - (220V, 0Hz, 3Ph, 2Pole) (C) 1C1-1 - (30V, 0Hz, 3Ph, 4Pole) 1 4C1- Locknut Front Bearing 1 2 0C-2 Bearing Ball 1 3 0C2-14 Bearing Housing, Front C2-30 Fan, Rotor 1 A C1-221 Rotor Shaft 34 4H 1 B C1-23 Rotor Shaft 34 4H 1 C C1-23 Rotor Shaft 34 4H 1 A 14C4- Stator & Band, B 14C4-244 Stator & Band, C 14C4-20 Stator & Band, C1-1 Bearing Housing, Rear 1 4C1- Locknut, Rear Bearing 1 4C1-10 Nut Bearing Screw 4 10 C1- Gear Set, 4H & H 1 302C1- Scr. Flat Hd. #10-32x1&1/ 2 1C4-10 Sleeve Cutout, 4 1 0C-4 Bearing Ball 1 14 C1- Washer, Loading Spring C3-3 Screw C-3 Cover, Rear Bearing C10-3 Scr. Round Hd. #-32x3/ C10-1 Scr. Binding Hd. #-32x1/4 1 1 C1-32 Washer, Lock # C1-3 Ground Wire Asm. (Grn/Yel) C14-4 Screw, Rd. Hd. #10-24 X 1/ C2-10 Switch Cover C10-4 Scr. Round Hd. #-32x3/ 2 24 C4-20 Switch Insulation 1 2 0C1- Switch, 1Ph 1 2 2C-1 Switch Mounting Bracket C10-2 Scr. Round Hd. #-32x1/4 2 2 C4-2 Switch Insulation 1 2 C-1 Spacing Washer A/R 30 1C-32 Drive Gear Spacing Sleeve C1-33 Carrying Handle 1 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 1 Form C-103
19 1 1 See Page for Complete Parts List Part of C1- Eastman Over a Century of Cutting Expertise Form C-103 1
20 Eastman 4BKH and 4CCH- Single Phase Motors (A) 1C (0V, 0Hz, 1Ph, 2Pole) (B) 1C (0V, 0Hz, 1Ph, 2Pole) (C) 1C (0V, 0Hz, 1Ph, 4Pole) (D) 1C1-0 - (220V, 0Hz, 1Ph, 2Pole) (E) 1C1-0 - (220V, 0Hz, 1Ph, 4Pole) (F) 1C (220V, 0Hz, 1Ph, 2Pole) 1 4C1- Locknut Front Bearing 1 2 0C-2 Bearing Ball 1 3 0C2-143 Bearing Housing, Front C2-2 Fan, Rotor 1 C3-233 Rotor Shaft 4 H 1 A 14C4-20 Stator & Band, 00 1 B 14C4-20 Stator & Band, 00 1 C 14C4-221 Stator & Band, D 14C4-20 Stator & Band, E 14C4-2 Stator & Band, F 14C4-20 Stator & Band, C2- Bearing Housing, Rear 1 4C1- Locknut, Rear Bearing 1 A C2-22 Cut-Out Auto 0CY 4 1 B C2-21 Cut-Out Auto 0CY 4 1 C C2-23 Cut-Out Auto 0CY 4PL 1 D C2-22 Cut-Out Auto 0CY 4 1 E C2-24 Cut-Out 0CY 4PL 1 F C2-21 Cut-Out Auto 0CY C1-0 Cut-Out Switch C-3 Scr. Round Hd. #-32x3/ 2 C-10 Insulation for Switch 1 0C-4 Bearing Ball 1 14 C1- Washer, Loading Spring C3-34 Screw, Bearing (Special) 4 1 3C-3 Cover, Rear Bearing C10-3 Scr. Round Hd. #-32x3/ 3 1 4C1-1 Nut Bearing Screw 4 1 C1- Gear Set, 4H & H C1- Scr. Flat Hd. #10-32x1&1/ C2-104 Switch Cover 3Ph C10-4 Scr. Round Hd. #-32x3/ 2 23 C4-41 Switch Insulation C1- Switch, On/Off 1 2 2C-11 Switch Mounting Bracket C10-2 Scr. Round Hd. #-32x1/4 2 2 C4-2 Switch Insulation C10-1 Scr. Binding Hd. #-32x1/4 1 2 C1-32 Washer, Lock # C1-3 Ground Wire Asm. (Grn/Yel) 1 31 C-1 Spacing Washer A/R 32 1C-33 Drive Gear Spacing Sleeve C1-32 Carrying Handle C14-4 Screw, Rd. Hd. #10-24 X 1/2 2 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 20 Form C-103
21 See Page for Complete Parts List Part of C1- Eastman Over a Century of Cutting Expertise Form C
22 Eastman 4BKH and 4CCH - Three Phase Motors (A) 1C1-1 - (220V, 0Hz, 3Ph, 2Pole) (B) 1C1-1 - (220V, 0Hz, 3Ph, 4Pole) (C) 1C1-4 - (30V, 0Hz, 3Ph, 2Pole) (D) 1C (440V, 0Hz, 3Ph, 2Pole) 1 4C1- Locknut Front Bearing 1 2 0C-2 Bearing Ball 1 3 0C2-143 Bearing Housing, Front C2-2 Fan, Rotor 1 C4-31 Rotor Shaft 4 H 1 A 14C4-2 Stator & Band, B 14C4-21 Stator & Band, C 14C4-21 Stator & Band, D 14C4-24 Stator & Band, C1- Bearing Housing, Rear 1 4C1- Locknut, Rear Bearing 1 4C1-1 Nut Bearing Screw 4 10 C1- Gear Set, 4H & H 1 302C1- Scr. Flat Hd. #10-32x1&1/ 2 1C4-10 Sleeve Cutout, 4 1 0C-4 Bearing Ball 1 14 C1- Washer, Loading Spring C3-34 Screw, Bearing (Special) 4 1 3C-3 Cover, Rear Bearing, C10-3 Scr. Round Hd. #-32x3/ C10-1 Scr. Binding Hd. #-32x1/4 1 1 C1-32 Washer, Lock # C1-3 Ground Wire Asm. (Grn/Yel) C14-4 Screw, Rd. Hd. #10-24 X 1/ C2-104 Switch Cover 3PH, C10-4 Scr. Round Hd. #-32x3/ 2 24 C4-41 Switch Insulation 1 2A 0C1- Switch, 1Ph 1 2B 0C1- Switch, 1Ph 1 2C 0C1- Switch, 3Ph 2 1 2D 0C1- Switch, Dual Voltage 1 2 2C-11 Switch Mounting Bracket C10-2 Scr. Round Hd. #-32x1/4 2 2 C4-2 Switch Insulation 1 2 C-1 Spacing Washer A/R 30 1C-33 Drive Gear Spacing Sleeve C1-32 Carrying Handle 1 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 22 Form C-103
23 1 1 See Page for Complete Parts List Part of C1- Eastman Over a Century of Cutting Expertise Form C
24 Eastman 4 2H- Single Phase Motors (A) 1C (0V, 0Hz, 1Ph, 2Pole) (B) 1C (0V, 0Hz, 1Ph, 2Pole) (C) 1C (0V, 0Hz, 1Ph, 4Pole) (D) 1C (220V, 0Hz, 1Ph, 2Pole) (E) 1C (220V, 0Hz, 1Ph, 4Pole) (F) 1C (220V, 0Hz, 1Ph, 2Pole) 1 4C1- Locknut Front Bearing 1 2 0C-2 Bearing Ball 1 3 0C2-143 Bearing Housing, Front C2-2 Fan, Rotor 1 C3-230 Rotor Shaft 4 2H 1 A 14C4-20 Stator & Band, 00 1 B 14C4-20 Stator & Band, 00 1 C 14C4-2 Stator & Band, D 14C4-20 Stator & Band, E 14C4-2 Stator & Band, F 14C4-20 Stator & Band, C2- Bearing Housing, Rear 1 4C1- Locknut, Rear Bearing 1 A C2-22 Cut-Out Auto 0CY 4 1 B C2-21 Cut-Out Auto 0CY 4 1 C C2-23 Cut-Out Auto 0CY 4PL 1 D C2-22 Cut-Out Auto 0CY 4 1 E C2-24 Cut-Out 0CY 4PL 1 F C2-21 Cut-Out Auto 0CY C1-0 Cut-Out Switch C-3 Scr. Round Hd. #-32x3/ 2 C-10 Insulation for Switch 1 0C-4 Bearing Ball 1 14 C1- Washer, Loading Spring C3-34 Screw, Bearing (Special) 4 1 3C-3 Cover, Rear Bearing C10-3 Scr. Round Hd. #-32x3/ 3 1 4C1-1 Nut Bearing Screw 4 1 C1-14 Gear Set, 2H & H C1- Scr. Flat Hd. #10-32x1&1/ C2-104 Switch Cover 3Ph C10-4 Scr. Round Hd. #-32x3/ 2 23 C4-41 Switch Insulation C1- Switch, On/Off 1 2 2C-11 Switch Mounting Bracket C10-2 Scr. Round Hd. #-32x1/4 2 2 C4-2 Switch Insulation C10-1 Scr. Binding Hd. #-32x1/4 1 2 C1-32 Washer, Lock # C1-3 Ground Wire Asm. (Grn/Yel) 1 31 C-1 Spacing Washer A/R 32 1C-30 Drive Gear Spacing Sleeve C1-32 Carrying Handle C14-4 Screw, Rd. Hd. #10-24 X 1/2 2 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 24 Form C-103
25 See Page for Complete Parts List Part of C1-14 Eastman Over a Century of Cutting Expertise Form C-103 2
26 Eastman 4 2H - Three Phase Motors (A) 1C1-2 - (220V, 0Hz, 3Ph, 2Pole) (B) 1C (220V, 0Hz, 3Ph, 2Pole) (C) 1C (220V, 0Hz, 3Ph, 4Pole) (D) 1C1-3 - (30V, 0Hz, 3Ph, 2Pole) 1 4C1- Locknut Front Bearing 1 2 0C-2 Bearing Ball 1 3 0C2-143 Bearing Housing, Front C2-2 Fan, Rotor 1 C3-230 Rotor Shaft 4 2H 1 A 14C4-214 Stator & Band, B 14C4-2 Stator & Band, C 14C4-21 Stator & Band, D 14C4-21 Stator & Band, C1- Bearing Housing, Rear 1 4C1- Locknut, Rear Bearing 1 4C1-1 Nut Bearing Screw 4 10 C1-14 Gear Set, 4H & H 1 302C1- Scr. Flat Hd. #10-32x1&1/ 2 1C4-10 Sleeve Cutout, 4 1 0C-4 Bearing Ball 1 14 C1- Washer, Loading Spring C3-34 Screw, Bearing (Special) 4 1 3C-3 Cover, Rear Bearing, C10-3 Scr. Round Hd. #-32x3/ C10-1 Scr. Binding Hd. #-32x1/4 1 1 C1-32 Washer, Lock # C1-3 Ground Wire Asm. (Grn/Yel) C14-4 Screw, Rd. Hd. #10-24 X 1/ C2-104 Switch Cover 3PH, C10-4 Scr. Round Hd. #-32x3/ 2 24 C4-41 Switch Insulation 1 2 0C1- Switch, 1Ph 1 2 2C-11 Switch Mounting Bracket C10-2 Scr. Round Hd. #-32x1/4 2 2 C4-2 Switch Insulation 1 2 C-1 Spacing Washer A/R 30 1C-33 Drive Gear Spacing Sleeve C1-32 Carrying Handle 1 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 2 Form C-103
27 1 1 See Page for Complete Parts List Part of C1-14 Eastman Over a Century of Cutting Expertise Form C-103 2
28 Eastman 4 H- Single Phase Motors (A) 1C (0V, 0Hz, 1Ph, 2Pole) (B) 1C (0V, 0Hz, 1Ph, 2Pole) (C) 1C1-0 - (0V, 0Hz, 1Ph, 4Pole) (D) 1C (220V, 0Hz, 1Ph, 2Pole) (E) 1C1- - (220V, 0Hz, 1Ph, 4Pole) (F) 1C (220V, 0Hz, 1Ph, 2Pole) (G) 1C (220V, 0Hz, 1Ph, 2Pole) 1 4C1- Locknut Front Bearing 1 2 0C-2 Bearing Ball 1 3 0C2-143 Bearing Housing, Front C2-2 Fan, Rotor 1 C3-230 Rotor Shaft 4 2H 1 A 14C4-20 Stator & Band, 00 1 B 14C4-20 Stator & Band, 00 1 C 14C4-2 Stator & Band, D 14C4-20 Stator & Band, E 14C4-2 Stator & Band, F 14C4-20 Stator & Band, G 14C4-20 Stator & Band, C2- Bearing Housing, Rear 1 4C1- Locknut, Rear Bearing 1 A C2-22 Cut-Out Auto 0CY 4 1 B C2-21 Cut-Out Auto 0Cy 4 1 C C2-23 Cut-Out Auto 0Cy 4Pl 1 D C2-22 Cut-Out Auto 0Cy 4 1 E C2-24 Cut-Out 0Cy 4Pl 1 F C2-21 Cut-Out Auto 0Cy 4 1 G C2-31 Cutout Assm Semko C1-0 Cut-Out Switch C-3 Scr. Round Hd. #-32X3/ 2 C-10 Insulation for Switch 1 0C-4 Bearing Ball 1 14 C1- Washer, Loading Spring C3-34 Screw, Bearing (Special) 4 1 3C-3 Cover, Rear Bearing C10-3 Scr. Round Hd. #-32x3/ 3 1 4C1-1 Nut Bearing Screw 4 1 C1-14 Gear Set, 2H & H C1- Scr. Flat Hd. #10-32x1&1/ C2-104 Switch Cover 3Ph C10-4 Scr. Round Hd. #-32x3/ 2 23 C4-41 Switch Insulation 1 23G C4-1 Switch Insulation C1- Switch, On/Off 1 24G 0C1-2 Switch, On/Off 1PH 1 2 2C-11 Switch Mounting Bracket C10-2 Scr. Round Hd. #-32x1/4 2 2 C4-2 Switch Insulation C10-1 Scr. Binding Hd. #-32x1/4 1 2 C1-32 Washer, Lock # C1-3 Ground Wire Asm. (Grn/Yel) 1 31 C-1 Spacing Washer A/R 32 1C-30 Drive Gear Spacing Sleeve C1-32 Carrying Handle C14-4 Screw, Rd. Hd. #10-24 X 1/2 2 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 2 Form C-103
29 See Page for Complete Parts List Part of C1-14 Eastman Over a Century of Cutting Expertise Form C-103 2
30 Eastman 4 H - Three Phase Motors (A) 1C (220V, 0Hz, 3Ph, 2Pole) (B) 1C (220V, 0Hz, 3Ph, 4Pole) (C) 1C1- - (30V, 0Hz, 3Ph, 2Pole) 1 4C1- Locknut Front Bearing 1 2 0C-2 Bearing Ball 1 3 0C2-143 Bearing Housing, Front C2-2 Fan, Rotor 1 C3-234 Rotor Shaft 4 H 1 A 14C4-2 Stator & Band, B 14C4-21 Stator & Band, C 14C4-21 Stator & Band, C2- Bearing Housing, Rear 1 4C1- Locknut, Rear Bearing 1 4C1-1 Nut Bearing Screw 4 10 C1-14 Gear Set, 4H & H 1 302C1- Scr. Flat Hd. #10-32x1&1/ 2 1C4-10 Sleeve Cutout, 4 1 0C-4 Bearing Ball 1 14 C1- Washer, Loading Spring C3-34 Screw, Bearing (Special) 4 1 3C-3 Cover, Rear Bearing, C10-3 Scr. Round Hd. #-32x3/ C10-1 Scr. Binding Hd. #-32x1/4 1 1 C1-32 Washer, Lock # C1-3 Ground Wire Asm. (Grn/Yel) C14-4 Screw, Rd. Hd. #10-24 X 1/ C2-104 Switch Cover 3PH, C10-4 Scr. Round Hd. #-32x3/ 2 24 C4-41 Switch Insulation 1 24C C4-1 Switch Insulation 1 2 0C1- Switch, 1Ph 1 2 2C-11 Switch Mounting Bracket C10-2 Scr. Round Hd. #-32x1/4 2 2 C4-2 Switch Insulation 1 2C C4-2 Switch Insulation 1 2 C-1 Spacing Washer A/R 30 1C-31 Drive Gear Spacing Sleeve C1-32 Carrying Handle 1 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 30 Form C-103
31 1 1 See Page for Complete Parts List Part of C1-14 Eastman Over a Century of Cutting Expertise Form C
32 Eastman 2 X - Single Phase Motors (A) 1C1- - (0V, 0Hz, 1Ph, 2Pole) (B) 1C1- - (0V, 0Hz, 1Ph, Pole) (C) 1C1- - (220V, 0Hz, 1Ph, 2Pole) (D) 1C1-0 - (220V, 0Hz, 1Ph, 2Pole) (E) 1C1- - (220V, 0Hz, 1Ph, 2Pole) (F) 1C1-4 - (220V, 0Hz, 1Ph, Pole) (G) 1C (220V, 0Hz, 1Ph, 2Pole) 1 301C-1 Scr. Fil. Hd. #4-40 X 1/ C-3 Cover, Rear Bearing, C1-4 Nut, Shaft Lock Jam 3/ C1-43 Fan, Motor 2 1 1C4- Sleeve Cutout C-1 Scr. Binding Hd. #4-40X1/4 3 30C1- Cap Dust 1 A C2-14 Cutout Assm 0Cy 2 1 B C2-2 Cutout Assm 0Cy DS 1 C C2-1 Cutout Assm 0Cy 2 1 D C2-2 Cutout Assm 0Cy DS 1 E C2-14 Cutout Assm 0Cy 2 1 F C2-2 Cutout Assm 0Cy DS 1 G C2-33 Cutout Semko C-3 Screw,Fil.Hd.#-32 X 3/ 2 10A 0C1- E Switch Cutout, Single Speed 1 10B 0C1- E Switch Cutout DS 1 10C 0C1- E Switch Cutout, Single Speed 1 10D 0C1- E Switch Cutout DS 1 10E 0C1- E Switch Cutout, Single Speed 1 10F 0C1- E Switch Cutout DS 1 10G 0C1- E Switch Cutout, Single Speed 1 C-10 Insul Switch 1 C1- Washer, Loading Spring 1 0C-4 Bearing Ball C1- Scr. Round Hd. #10-32x/ C1-34 Handle Carry C3-2 Screw, Front to Rear Bearing 4 1 C-4 Insul. Rubber 2 1 C1-1 Gear Set, X & X 1 1A 14C4- Stator & Band, B 14C4-10 Stator & Band, C 14C4-141 Stator & Band, D 14C4-221 Stator & Band, E 14C4-140 Stator & Band, F 14C4-1 Stator & Band, G 14C4-141 Stator & Band, C1-3 Ground Wire Asm. (Grn/Yel) C1- Brg. Housing Rear 1 22 C1-32 Washer, Lock # C10-1 Scr. Binding Hd. #-32X1/ C1- Screw,Flt.Hd.#10-32 X 1&1/ 2 2 2C1-1 Bracket Switch C- Scr. Round Hd. #-32X/1 4 2A 0C1- Switch, 1Ph 1 2B 0C1- Switch, 1Ph 1 2C 0C1- Switch, 1Ph 1 2D 0C1- Switch, 1Ph 1 2E 0C1- Switch, 1Ph 1 2F 0C1- Switch, 1Ph 1 2G 0C1-2 Switch, 1Ph Semko 1 2 2C-14 Switch Mounting Bracket C-3 Scr. Round Hd. #4-3x1/ C1- Rotor Shaft 2 X C2-14 Bearing Housing, Front C1-1 Nut Bearing Screw C-2 Bearing Ball C1- Locknut Front Bearing 1 3 C-1 Spacing Washer A/R A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 32 Form C-103
33 See Page for Complete Parts List Part of C1-1 Eastman Over a Century of Cutting Expertise Form C
34 Eastman 2 X - Three Phase Motors (A) 1C1- - (220V, 0Hz, 3Ph, 2Pole) (B) 1C1-0 - (30V, 0Hz, 3Ph, 2Pole) 1 301C-1 Scr. Fil. Hd. #4-40 X 1/ C-3 Cover, Rear Bearing, C1-4 Nut, Shaft Lock Jam 3/ C1-43 Fan, Motor 2 1 1C4- Sleeve Cutout C-1 Scr. Binding Hd. #4-40x1/4 3 30C1- Cap Dust 1 300C-3 Scr. Round Hd. #-32x3/ 2 C1-10 Mount Cutout 1 10 C1- Washer, Loading Spring 1 0C-4 Bearing Ball 1 300C1- Scr. Round Hd. #10-32x/ 2 22C1-34 Handle Carry C3-2 Screw, Front to Rear Bearing 4 1 0C1- Brg. Housing Rear 1 1A 14C4-142 Stator & Band, B 14C4-144 Stator & Band, C1- Rotor Shaft 2 X 1 1 3C1-3 Ground Wire Asm. (Grn/Yel) 1 1 C1-32 Washer, Lock # C10-1 Scr. Binding Hd. #-32x1/ C1- Scr. Flat Hd. #10-32x1&1/ C1-1 Bracket Switch C- Scr. Round Hd. #-32x/ C1- Switch, 1Ph 1 2 2C-14 Switch Mounting Bracket C-3 Scr. Round Hd. #4-3x1/ C2-14 Bearing Housing, Front 1 2 4C1-1 Nut Bearing Screw 4 2 0C-2 Bearing Ball C1- Locknut Front Bearing 1 31 C-1 Spacing Washer A/R 32 C1-1 Gear Set, X & X 1 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 34 Form C-103
35 See Page for Complete Parts List Part of C Eastman Over a Century of Cutting Expertise Form C-103 3
36 Eastman 2 X and 2BKX - Single Phase Motors (A) 1C (0V, 0Hz, 1Ph, 2Pole) (B) 1C1- - (0V, 0Hz, 1Ph, 4Pole) (C) 1C1-2 - (0V, 0Hz, 1Ph, Pole) (D) 1C (220V, 0Hz, 1Ph, 2Pole) (E) 1C1-4 - (220V, 0Hz, 1Ph, Pole) (F) 1C (220V, 0Hz, 1Ph, 2Pole) (G) 1C1- - (220V, 0Hz, 1Ph, Pole) 1 301C-1 Scr. Fil. Hd. #4-40 X 1/ C-3 Cover, Rear Bearing, C1-4 Nut, Shaft Lock Jam 3/ C1-43 Fan, Motor 2 1 1C4- Sleeve Cutout C-1 Scr. Binding Hd. #4-40X1/4 3 30C1- Cap Dust 1 A C2-14 Cutout Assm 0Cy 2 1 B C2-1 Cutout Assm 0Cy 4PL 1 C C2-2 Cutout Assm 0Cy DS 1 D C2-1 Cutout Assm 0Cy DS 1 E C2-2 Cutout Assm 0Cy DS 1 F C2-14 Cutout Assm 0Cy 2 1 G C2-2 Cutout Assm 0Cy DS 1 301C-3 Screw,Fil.Hd.#-32 X 3/ 2 10A 0C1- E Switch Cutout, Single Speed 1 10B 0C1- E Switch Cutout Single Speed 1 10C 0C1- E Switch Cutout, DS 1 10D 0C1- E Switch Cutout Single Speed 1 10E 0C1- E Switch Cutout, DS 1 10F 0C1- E Switch Cutout Single Speed 1 10G 0C1- E Switch Cutout, DS 1 C-10 Insul Switch 1 C1- Washer, Loading Spring 1 0C-4 Bearing Ball C1- Scr. Round Hd. #10-32x/ C1-34 Handle Carry C3-2 Screw, Front to Rear Bearing 4 1 C-4 Insul. Rubber 2 1 C1-1 Gear Set, X & X 1 1A 14C4- Stator & Band, B 14C4-2 Stator & Band, C 14C4-10 Stator & Band, D 14C4-141 Stator & Band, E 14C4-221 Stator & Band, F 14C4-140 Stator & Band, G 14C4-1 Stator & Band, C1-3 Ground Wire Asm. (Grn/Yel) C1- Brg. Housing Rear 1 22 C1-32 Washer, Lock # C10-1 Scr. Binding Hd. #-32X1/ C1- Screw,Flt.Hd.#10-32 X 1&1/ 2 2 2C1-1 Bracket Switch C- Scr. Round Hd. #-32X/1 4 2A 0C1- Switch, 1Ph 1 2B 0C1- Switch, 1Ph 1 2C 0C1- Switch, 1Ph 1 2D 0C1- Switch, 1Ph 1 2E 0C1- Switch, 1Ph 1 2F 0C1- Switch, 1Ph 1 2G 0C1- Switch, 1Ph 1 2 2C-14 Switch Mounting Bracket C-3 Scr. Round Hd. #4-3x1/ C1- Rotor Shaft 2 X C2-14 Bearing Housing, Front C1-1 Nut Bearing Screw C-2 Bearing Ball C1- Locknut Front Bearing 1 3 C-1 Spacing Washer A/R 3 1C-3 Sleeve Spc Dr Gr X 1 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 3 Form C-103
37 See Page for Complete Parts List Part of C1-1 Eastman Over a Century of Cutting Expertise Form C-103 3
38 Eastman 2 X and 2BKX - Three Phase Motors (A) 1C (220V, 0Hz, 3Ph, 2Pole) (B) 1C (220V, 0Hz, 3Ph, Pole) (C) 1C1-0 - (30V, 0Hz, 3Ph, 2Pole) 1 301C-1 Scr. Fil. Hd. #4-40 X 1/ C-3 Cover, Rear Bearing, C1-4 Nut, Shaft Lock Jam 3/ C1-43 Fan, Motor 2 1 1C4- Sleeve Cutout C-1 Scr. Binding Hd. #4-40x1/4 3 30C1- Cap Dust 1 300C-3 Scr. Round Hd. #-32x3/ 2 C1-10 Mount Cutout 1 10 C1- Washer, Loading Spring 1 0C-4 Bearing Ball 1 300C1- Scr. Round Hd. #10-32x/ 2 22C1-34 Handle Carry C3-2 Screw, Front to Rear Bearing 4 1 C1-1 Gear Set, X & X 1 1A 14C4-142 Stator & Band, B 14C4-1 Stator & Band, C 14C4-144 Stator & Band, C1- Rotor Shaft 2 X 1 1 3C1-3 Ground Wire Asm. (Grn/Yel) 1 1 C1-32 Washer, Lock # C10-1 Scr. Binding Hd. #-32x1/ C1- Scr. Flat Hd. #10-32x1&1/ C1-1 Bracket Switch C- Scr. Round Hd. #-32x/ C1- Switch, 1Ph 1 2 2C-14 Switch Mounting Bracket C-3 Scr. Round Hd. #4-3x1/ C2-14 Bearing Housing, Front 1 2 4C1-1 Nut Bearing Screw 4 2 0C-2 Bearing Ball C1- Locknut Front Bearing 1 31 C-1 Spacing Washer A/R 32 1C-3 Sleeve Spc Dr Gr X C1- Brg. Housing Rear 1 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 3 Form C-103
39 See Page for Complete Parts List Part of C1-1 Eastman Over a Century of Cutting Expertise Form C-103 3
40 Eastman X - Single Phase Motors (A) 1C1- - (0V, 0Hz, 1Ph, 2Pole) (B) 1C1-4 - (0V, 0Hz, 1Ph, Pole) (C) 1C1-0 - (220V, 0Hz, 1Ph, 2Pole) (D) 1C1-4 - (220V, 0Hz, 1Ph, Pole) (E) 1C (220V, 0Hz, 1Ph, 2Pole) 1 301C-1 Scr. Fil. Hd. #4-40 X 1/ C-3 Cover, Rear Bearing, C1-4 Nut, Shaft Lock Jam 3/ C1-43 Fan, Motor 2 1 1C4- Sleeve Cutout C-1 Scr. Binding Hd. #4-40X1/4 3 30C1- Cap Dust 1 A C2-14 Cutout Assm 0Cy 2 1 B C2-2 Cutout Assm 0Cy DS 1 C C2-1 Cutout Assm 0Cy 2 1 D C2-1 Cutout Assm 0Cy 2 1 E C2-33 Cutout Assm 0Cy Semko 1 301C-3 Screw,Fil.Hd.#-32 X 3/ C1- E Switch Cutout, Single Speed 1 C-10 Insul Switch 1 C1- Washer, Loading Spring 1 0C-4 Bearing Ball C1- Scr. Round Hd. #10-32x/ C1-34 Handle Carry C3-2 Screw, Front to Rear Bearing 4 1 C-4 Insul. Rubber 2 1 C1-1 Gear Set, X & X 1 1A 14C4-14 Stator & Band, B 14C4-10 Stator & Band, C 14C4-1 Stator & Band, D 14C4-22 Stator & Band, E 14C4-20 Stator & Band, C1-3 Ground Wire Asm. (Grn/Yel) C1- Brg. Housing Rear 1 22 C1-32 Washer, Lock # C10-1 Scr. Binding Hd. #-32X1/ C1- Screw,Flt.Hd.#10-32 X 1&1/ 2 2 2C1-1 Bracket Switch C- Scr. Round Hd. #-32X/1 4 2A 0C1- Switch, 1Ph 1 2B 0C1- Switch, 1Ph 1 2C 0C1- Switch, 1Ph 1 2D 0C1- Switch, 1Ph 1 2E 0C1-2 Switch, 1Ph Semko 1 2 2C-14 Switch Mounting Bracket C-3 Scr. Round Hd. #4-3x1/ C1- Rotor Shaft 2 X C2-14 Bearing Housing, Front C1-1 Nut Bearing Screw C-2 Bearing Ball C1- Locknut Front Bearing 1 3 C-1 Spacing Washer A/R A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 40 Form C-103
41 See Page for Complete Parts List Part of C Eastman Over a Century of Cutting Expertise Form C
42 Eastman X - Three Phase Motors (A) 1C1-3 - (220V, 0Hz, 3Ph, 2Pole) (B) 1C1- - (220V, 0Hz, 3Ph, Pole) (C) 1C1- - (220V, 0Hz, 3Ph, Pole) 1 301C-1 Scr. Fil. Hd. #4-40 X 1/ C-3 Cover, Rear Bearing, C1-4 Nut, Shaft Lock Jam 3/ C1-43 Fan, Motor 2 1 1C4- Sleeve Cutout C-1 Scr. Binding Hd. #4-40x1/4 3 30C1- Cap Dust 1 300C-3 Scr. Round Hd. #-32x3/ 2 C1-10 Mount Cutout 1 10 C1- Washer, Loading Spring 1 0C-4 Bearing Ball 1 300C1- Scr. Round Hd. #10-32x/ 2 22C1-34 Handle Carry C3-2 Screw, Front to Rear Bearing 4 1 0C1- Brg. Housing Rear 1 1A 14C4-14 Stator & Band, B 14C4-22 Stator & Band, A 14C4-222 Stator & Band, C1- Rotor Shaft 2 X 1 1 3C1-3 Ground Wire Asm. (Grn/Yel) 1 1 C1-32 Washer, Lock # C10-1 Scr. Binding Hd. #-32x1/ C1- Scr. Flat Hd. #10-32x1&1/ C1-1 Bracket Switch C- Scr. Round Hd. #-32x/ C1- Switch, 1Ph 1 2 2C-14 Switch Mounting Bracket C-3 Scr. Round Hd. #4-3x1/ C2-14 Bearing Housing, Front 1 2 4C1-1 Nut Bearing Screw 4 2 0C-2 Bearing Ball C1- Locknut Front Bearing 1 31 C-1 Spacing Washer A/R 32 C1-1 Gear Set, X & X 1 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 42 Form C-103
43 See Page for Complete Parts List Part of C1-1 Eastman Over a Century of Cutting Expertise Form C
44 Eastman X and BKX - Single Phase Motors (A) 1C (0V, 0Hz, 1Ph, 2Pole) (B) 1C1-1 - (0V, 0Hz, 1Ph, 4Pole) (C) 1C (0V, 0Hz, 1Ph, Pole) (D) 1C1-2 - (220V, 0Hz, 1Ph, 2Pole) (E) 1C (220V, 0Hz, 1Ph, 4Pole) (F) 1C1-4 - (220V, 0Hz, 1Ph, Pole) (G) 1C (220V, 0Hz, 1Ph, 2Pole) (H) 1C1-2 - (220V, 0Hz, 1Ph, Pole) 1 301C-1 Scr. Fil. Hd. #4-40 X 1/ C-3 Cover, Rear Bearing, C1-4 Nut, Shaft Lock Jam 3/ C1-43 Fan, Motor 2 1 1C4- Sleeve Cutout C-1 Scr. Binding Hd. #4-40X1/4 3 30C1- Cap Dust 1 A C2-14 Cutout Assm 0Cy 2 1 B C2-1 Cutout Assm 0Cy 4PL 1 C C2-2 Cutout Assm 0Cy DS 1 D C2-1 Cutout Assm 0Cy DS 1 E C2-14 Cutout Assm 0Cy 2 1 F C2-2 Cutout Assm 0Cy DS 1 G C2-1 Cutout Assm 0Cy DS 1 H C2-2 Cutout Assm 0Cy DS 1 301C-3 Screw,Fil.Hd.#-32 X 3/ C1- E Switch Cutout, Single Speed 1 C-10 Insul Switch 1 C1- Washer, Loading Spring 1 0C-4 Bearing Ball C1- Scr. Round Hd. #10-32x/ C1-34 Handle Carry C3-2 Screw, Front to Rear Bearing 4 1 C-4 Insul. Rubber 2 Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 1 C1-1 Gear Set, X & X 1 1A 14C4-14 Stator & Band, B 14C4-1 Stator & Band, C 14C4-10 Stator & Band, D 14C4-1 Stator & Band, E 14C4- Stator & Band, F 14C4-22 Stator & Band, G 14C4-200 Stator & Band, H 14C4-22 Stator & Band, C1-3 Ground Wire Asm. (Grn/Yel) C1- Brg. Housing Rear 1 22 C1-32 Washer, Lock # C10-1 Scr. Binding Hd. #-32X1/ C1- Screw,Flt.Hd.#10-32 X 1&1/ 2 2 2C1-1 Bracket Switch C- Scr. Round Hd. #-32X/1 4 2A 0C1- Switch, 1Ph 1 2B 0C1- Switch, 1Ph 1 2C 0C1- Switch, 1Ph 1 2D 0C1- Switch, 1Ph 1 2E 0C1- Switch, 1Ph 1 2F 0C1- Switch, 1Ph 1 2G 0C1- Switch, 1Ph 1 2H 0C1- Switch, 1Ph 1 2 2C-14 Switch Mounting Bracket C-3 Scr. Round Hd. #4-3x1/ C1- Rotor Shaft 2 X C2-14 Bearing Housing, Front C1-1 Nut Bearing Screw C-2 Bearing Ball C1- Locknut Front Bearing 1 3 C-1 Spacing Washer A/R 3 1C-3 Sleeve Spc Dr Gr X 1 44 Form C-103
45 See Page for Complete Parts List Part of C1-1 Eastman Over a Century of Cutting Expertise Form C-103 4
46 Eastman X and BKX - Three Phase Motor 1C (220V, 0Hz, 3Ph, 2Pole) 1 301C-1 Scr. Fil. Hd. #4-40 X 1/ C-3 Cover, Rear Bearing, C1-4 Nut, Shaft Lock Jam 3/ C1-43 Fan, Motor 2 1 1C4- Sleeve Cutout C-1 Scr. Binding Hd. #4-40x1/4 3 30C1- Cap Dust 1 300C-3 Scr. Round Hd. #-32x3/ 2 C1-10 Mount Cutout 1 10 C1- Washer, Loading Spring 1 0C-4 Bearing Ball 1 300C1- Scr. Round Hd. #10-32x/ 2 22C1-34 Handle Carry C3-2 Screw, Front to Rear Bearing 4 1 C1-1 Gear Set, X & X C4-14 Stator & Band, C1- Rotor Shaft 2 X 1 1 3C1-3 Ground Wire Asm. (Grn/Yel) 1 1 C1-32 Washer, Lock # C10-1 Scr. Binding Hd. #-32x1/ C1- Scr. Flat Hd. #10-32x1&1/ C1-1 Bracket Switch C- Scr. Round Hd. #-32x/ C1- Switch, 1Ph 1 2 2C-14 Switch Mounting Bracket C-3 Scr. Round Hd. #4-3x1/ C2-14 Bearing Housing, Front 1 2 4C1-1 Nut Bearing Screw 4 2 0C-2 Bearing Ball C1- Locknut Front Bearing 1 31 C-1 Spacing Washer A/R 32 1C-3 Sleeve Spc Dr Gr X C1- Brg. Housing Rear 1 A/R = As Required Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts. 4 Form C-103
47 See Page for Complete Parts List Part of C1-1 Eastman Over a Century of Cutting Expertise Form C-103 4
48 Eastman 34/4 BK and Carpet Cutter Assembly A) 34BK4H B) 4BKH and 4CCH 1A C1-2 Standard & Brkt BK4H 1 1B C1-3 Standard & Brkt BKH 1 2A C1- Standard & Plow BK4H 1 2B C1-4 Standard & Plow BKH 1 3A 2C1-20 Bracket Std 4 BH 1 3B 2C1-203 Bracket Std BH C1- Screw,Flt.Hd.#10-32 X 3/4 302C-2 Screw,Flt.Hd.#-32 X /1 1 C1- Lever Switch 1Ph & 3Ph 4 1 C2- Knob Switch Lever 1 A 4C1- Locknut Handle 1 B 4C1-0 Locknut Handle 1 A 31C1- Handle Oper Small 1 B 31C1-3 Handle Oper Large 1 10A 2C4- Side Guard, 4" CC & BK 1 10B 2C4-14 Side Guard, 4" CC & BK 1 20C-1 Screw,Thumb 1 4C1-1 Locknut Knife 4& 1 30C- Screw,Pan Hd.#-32 X 1/ C-3 Screw,Flt.Hd.#-32 X 3/ Spc. 3 Note: Items, and are not applicable to Model See Guide Assembly Page See Motor Assembly Pages See Sharpener Assembly Page See Slitter and CC Base Plate Assembly 4H and H Page 0 For Knife Options See Page 14 4 Form C-103
49 2/ BK Assembly 1 C1- Std. & Brkt Bkx/Bkx Screw,Skt.Hd.#10-32 X 1/ Screw,Skt.Hd.#10-32 X 3/ 2 4 C-24 Plate Std To Brkt 1 C1-14 Standard F Brkt Bk 1 4C2-3 Insert Nut # C1-22 Brkt For Standard Bk 1 302C1-3 Screw,Flt.Hd.#10-32 X 1/2 4 2C-0 Adaptor Handle C1-1 Locknut Handle 1 14C1- Grip Handle 1 2C4-1 Knife Guard 1 20C-1 Screw,Thumb C14-1 Screw,Skt.Hd.#10-24 X C- Screw,Rd.Hd.#-32 X /1 1 4C1-1 Locknut Knf Rev Mach C-3 Screw,Skt.Set #-32 X 3/1 3 See Guide Assembly Page See Motor Assembly Pages See Sharpener Assembly Page For Knife Options See Page See Slitter and CC Base Plate Assembly X and X Page Eastman Over a Century of Cutting Expertise Form C-103 4
50 Eastman Slitter and CC Base Plate Assembly 4H and H 0C3-2 (34BK4H, 4BKH and 4CCH) 1 C-XXX See Chart 1 2 3C1- Plate Flat & Wing 1 3 C1-3 Throat Plate Washer C10-3 Screw,Rd.Hd.#-32 X /1 4 C4- Clip Roller Shaft 2 302C10-1 Screw,Flt.Hd.#-32 X 3/1 10 C4- Clip Roller Shaft 2 22C1-2 Roller Plate Front 14 1C-10 Ring Rubber 10 C-1 Washer,Plate Roller 41C2 Roller Plate 40 1C1-1 Shell Plate Roller 4 C2-4 Shaft Plt Roller 4 * 30C1-30 Skate for Plate BK 1 14* 302C10-2 Screw,Flt.Hd.#-32 X 1/4 4 *Not Shown Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts THROAT PLATES C-1 4" and -1/4" Knife C-14 " Knife C-1 " Knife C-1 X and X Knife 0 Form C-103
51 Slitter Base Plate Assembly X and X 0C3-232 (2BKX and BKX) 1 C-24 Plate Throat X C1-4 Plate Flat & Wing C-2 Screw,Rd.Hd.#-32 X 1/ C- Screw,Flt.Hd.#-32 X / 4 22C1-4 Roller Plate Front 2 1C-10 Ring Rubber 4 C-1 Washer,Plate Roller 4 C2- Shaft Plt Roller 2 1C1- Shell Plate Roller C2- Roller Plate 20 C4- Clip Roller Shaft 4 302C10-1 Screw,Flt.Hd.#-32 X 3/1 1C1- Roller Plate Rear C2- Roller Plate 20 1 C-1 Washer,Plate Roller 4 1 1C1- Shell Plate Roller 2 1 1C-10 Ring Rubber 2 1 C2-14 Shaft Plt Roller 1 1* 30C1-34 Skate For Plate 2-X 1 20* 302C10- Screw,Flt.Hd.#-32 X 3/ 4 *Not Shown Item numbers are for reference only. Please Specify MODEL SERIAL NUMBER and PART NUMBER when ordering replacement parts Eastman Over a Century of Cutting Expertise Form C-103 1
548 Falcon HD End Cutter
EASTMAN THE EASTMAN Falcon HD End Cutter with Lifting Mechanism Model: FALHDH Instruction Manual & Illustrated Parts List Please read completely before attempting to operate your new Falcon HD Track Cutter.
More informationElectrical Schematic and Pneumatic Wiring Diagrams
THE EASTMAN Raptor Electrical Schematic and Pneumatic Wiring Diagrams Technical Support: 1-800-87-5595 Please read completely before attempting to operate your new RAPTOR. ELECTRICAL HAZARD Electrical
More informationUniversal Sewing Supply
"Genuine" Parts For Eastman Straight Knives 4C1-99 4C1-150 SEE REPLACEMENT BELTS Model 627X BRUTE SEE SHARPENER HOUSING (FRONT VIEW) SEE SHARPENER HOUSING (REAR VIEW) 4C1-179 SEE KNIVES SEE LOWER GEAR
More informationInstructions & Illustrated Parts List
THE EASTMAN R C Model WB 7.2 Volt Heavy Duty Cordless Round Knife A CAUTION Machine Equipped With Sharp Blade Instructions & Illustrated Parts List D B Your new Worker Bee is designed to replace hand held
More informationAgri-Fab OWNERS MANUAL. Model No " ROUGH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully
Agri-Fab OWNERS MANUAL Model No. 45-03071 45-0361 CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts 42" ROUGH CUT TRAILMOWER the fastest way
More informationPARTS MANUAL ET60CT656SD ET60CT656SDCA ET72CT724RD ET72CT724RDCA
PARTS MANUAL ET60CT656SD ET60CT656SDCA ET72CT724RD ET72CT724RDCA 2 A DIVISION OF WORLDLAWN POWER EQUIPMENT, INC. WWW.ENCOREEQUIPMENT.COM 401 COMMERCE STREET BEATRICE, NE 68310 800-267-4255 FAX 402-223-4103
More informationD27300 Table PLANER THICKNESSER 2
D27300 Table PLANER THICKNESSER 2 D27300 Motor PLANER THICKNESSER 2 D27300 Rise & fall PLANER THICKNESSER 2 D27300 Table support PLANER THICKNESSER 2 1 860084-07 6 SCREW 3.2 x 32 No 2 868852-01 1 COVER
More informationSC-400, SC-550, SC-650 INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK
REV D: 0/8 INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL. ALL PURPOSE BREAKING SAW
More informationCONTENTS. VIKING PUMP, INC. A Unit of IDEX Corporation Cedar Falls, IA USA SECTION TSM 710.1
TECHNICAL SERVICE MANUAL industrial heavy duty motor speed pumps SERIES 4076 AND 4176 SIZES hle, ate and ale SECTION TSM 710.1 PAGE 1 of 8 ISSUE B CONTENTS Introduction....................... 1 Safety
More informationER48FX730VLCA ER52FX730VL ER52FX730VLCA
PARTS MANUAL ER48FX730VL ER48FX730VLCA ER52FX730VL ER52FX730VLCA 2 ENCORE MANUFACTURING A DIVISION OF WORLDLAWN POWER EQUIPMENT, INC. ENCOREEQUIPMENT.COM 2415 ASHLAND AVE BEATRICE, NE 68310 800-267-4255
More informationSECTION 9: PARTS Main Parts
SECTION 9: PARTS Main Parts 8 3 6 2 1 27 34 33 30 31 32 171 37 38 173 109 110 17 18 22 23 21 36 39 159 44-1 44 158 42 43 15-1 141 142 143 140 157 45 46 47 145 160147 49 50 153 154 41 164 99 28 100 104
More informationRYOBI 10 in. SLIDING MITER SAW w/laser MODEL NO. TSS100L REPAIR SHEET
RYOBI 10 in. SLIDING MITER SAW w/laser MODEL NO. TSS100L REPAIR SHEET 119 96 83 1 84 85 116 86 114 92 82 117 113 112 115 97 175 176 120 177 121 1 2 3 122 81 87 128 164 1 80 88 174 114 6 53 163 19 3 141
More informationAgri-Fab OWNERS MANUAL. Model No " ROUGH CUT TRAILMOWER. CAUTION: Read Rules for Safe Operation and Instructions Carefully
Agri-Fab OWNERS MANUAL Model No. 45-0362 CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts 42" ROUGH CUT TRAILMOWER NOTE: Your mower deck will
More informationGROB 4V-24 Parts. GrobBandSaw.com
GROB 4V- Parts GrobBandSaw.com 888-550-3116 18 19 20 21 22 5/16-18x1/2 Hex Head Cap Screw ( 14 ) 34 35 36 37 38 39 40 39 41 42 43 44 45 46 17 16 3/8-16x3/4 Hex Head Cap Screw ( 2 ) 31 30 15 5/16-18x1 Hex
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS MODEL D300 SERIES MIXERS (INCLUDES MOTOR PARTS) ML-134258 ML-134261 D300T (Timed) D300C (Timed) PRIOR MLS COVERED IN THIS MANUAL ML-134211 ML-134213 ML-104421 ML-134114 D300T
More informationCRAFTSMAN COMPOUND MITER SAW MODEL NUMBER REPAIR SHEET
CRAFTSMAN COMPOUND MITER SAW MODEL NUMBER 5.50 REPAIR SHEET CRAFTSMAN COMPOUND MITER SAW MODEL NUMBER 5.50 Figure A 4 5 7 8 0 4 5 7 8 0 5 4 7 8 0 5 4 5 7 8 40 4 4 4 44 45 4 4 47 48 50 4 5 5 4 5 54 5 55
More informationDisc Grinder Model G 18MR G 23MR G 23MRU
Disc Grinder Model G 18MR G 23MR G 23MRU Handling instructions G23MR NOTE: Before using this Electric Power Tool, carefully read through these HANDLING INSTRUCTIONS to ensure efficient, safe operation.
More information66cm Heavy-Duty Rear Bagger Lawn Mower
Form Number 3360-820 Rev B 66cm Heavy-Duty Rear Bagger Lawn Mower Model No. 22200TE - 280000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts, please supply the part number,
More informationOperating Manual Please Read Before Operating Unit
Always Moving Forward Operating Manual Please Read Before Operating Unit ST1 Portable Magnet Wire Stripper & Solder Tip Cleaner Service and All Spare Parts Available The Eraser Company, Inc. PO Box 4961/
More informationRepair Parts Parts List for RIDGID 10 Compound Miter Saw Model No. MS1065LZ RIDGID parts are available on-line at
0. Repair Parts Model No. MS0LZ 0 0 0 0 0 FIGURE A. 0. 0 0 0 0. 0 0 WARNING: The assembly shown represents an important part of the Double Insulated System. To avoid the possibility of alteration or damage
More informationWorldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE Toll Free Number:
Parts Catalog R WYRZ46S/50U/60U Residential Zero Turn Mower Worldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE 68310 Toll Free Number: 1-800-267-4255 Table of Contents Table
More informationELECTRIC TOOL PARTS LIST
Hitachi Power Tools LIST E942 ELECTRIC TOOL PARTS LIST SLIDE COMPOUND MITER SAW Model 2005 5 20 (E1) 1 2 3 60 61 62 63 64 19 20 21 A 65 47 48 45 49 50 51 6 17 37 46 38 44 23 24 22 25 24 A 26 27 39 28 40
More informationTECHNICAL DATA BROCHURE - ZTR 424 & 427 DATE 8/85 PAGE 1 OF 8
TECHNICAL DATA BROCHURE - ZTR 424 & 427 DATE 8/85 PAGE 1 OF 8 IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATION OR MAKING ADJUSTMENTS Deluxe Seat Adjustment Easy hand lever action allows forward and
More informationCATALOG OF REPLACEMENT PARTS
CATALOG OF REPLACEMENT PARTS MODEL D340 MIXER (INCLUDES MOTOR PARTS) D340 D340C ML-134254 ML-134257 PRIOR MLS COVERED IN THIS CATALOG D340 ML-134185 D340C ML-134188 D340 W/O Brake ML-104483 D340 W/Brake
More informationINSTRUCTION MANUAL ANGLE GRINDER PT W
INSTRUCTION MANUAL ANGLE GRINDER PT50360 4½ INCHES 120V 60Hz 600W 5A 12,000 rpm C US Note : Before operating this tool, read this manual and follow all safety rules and operating instructions. This electric
More informationJARVIS. Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner. 30CL-1 Hock Cutter
Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner 30CL-1 Hock Cutter with Leg Grabber 30CL-1 Hock Cutter 30CL-3 Dehorner Equipment Selection 30CL-1 Sheep Head Dropper Order Number 30CL-1 Hock Cutter 30CL-1
More informationRYOBI 10 in. SLIDING MITER SAW w/laser MODEL NO. TSS100L1 REPAIR SHEET
RYOBI 10 in. SLIDING MITER SAW w/laser MODEL NO. TSS100L1 REPAIR SHEET 32 96 119 31 1 85 116 86 114 92 82 117 113 112 115 97 1 6 121 1 84 59 81 87 122 128 34 174 80 66 88 114 19 79 78 115 117 116 125 126
More informationELECTRIC TOOL PARTS LIST
Hitachi Power Tools LIST E938 ELECTRIC TOOL PARTS LIST COMPOUND SAW Model 2004 10 1 (E1) 80 1 15 7 8 9 16 17 18 1 2 3 19 4 20 5 12 6 13 14 13 15 21 11 10 39 40 41 42 43 44 45 46 47 31 38 32 22 33 23 34
More informationWorldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE Toll Free Number:
Parts Catalog R WYRZ46S/50U/60U Residential Zero Turn Mower Worldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE 68310 Toll Free Number: 1-800-267-4255 Table of Contents Table
More informationBUSH HOG LAND MAINTENANCE REPAIR PARTS MANUAL MODELS: RPM & RPM SECTION: 79
BUSH HOG LAND MAINTENANCE REPAIR S MANUAL MODELS: -0 RPM & -000 RPM SECTION: 9 0 Griffin Ave. Selma, Al. 0 () - () -00 Parts Ordering -00-0- Fax -00-- www.bushhog.com April, 0 BUSH HOG/ LAND MAINTENANCE
More informationMid-Size ProLine, T-Bar, Gear Drive 13 HP with 91cm Side Discharge Mower
Form Number 3350-754 Rev B Mid-Size ProLine, T-Bar, Gear Drive 13 HP with 91cm Side Discharge Mower Model No. 30314TE - 250000001 and up. Parts Catalog Ordering Replacement Parts To order replacement parts,
More informationLAND MAINTENANCE REPAIR PARTS MANUAL BUSH HOG MODEL: 307 SECTION: 16
BUSH HOG LAND MAINTENANCE REPAIR S MANUAL MODEL: 0 SECTION: P.O. Box 0 Selma, AL 0-0 () - () -00 Parts Ordering -00-0- Fax -00-- www.bushhog.com BUSH HOG / LAND MAINTENANCE REPAIR S MANUAL SEPTEMBER, 0
More informationSAFETY. Hitchpole, centre frame 1. Centre frame wheels & roller 3. Centre & wing frames 5. Wing frame wheels & roller 9.
MANUAL Hitchpole, centre frame 1 Centre frame wheels & roller 3 Centre & wing frames Wing frame wheels & roller 9 Hydraulics 11 Clearance lights 13 Operations 1 Safety, warranty 1 SAFETY Industrial Drive,
More informationBUSH HOG LAND MAINTENANCE REPAIR PARTS MANUAL MODEL: 280 SERIES SECTION: 59
BUSH HOG LAND MAINTENANCE REPAIR S MANUAL MODEL: 0 SERIES SECTION: 0 Griffin Ave. Selma, AL 0 () () 00 Parts Ordering 00 0 Fax 00 www.bushhog.com BUSH HOG/ LAND MAINTENANCE REPAIR S MANUAL October, 0 0
More informationSCROLL SAW SS-10 PART NO DATE:
40-680 20 SCROLL SAW SS-10 PART NO. 1342406 DATE: 06-09-04 Page1/ SS-10/DEB REPLACEMENT PARTS 1 n 901-02-050-5634 6-32 X 1/2" ROUND HD SCREW 2 1342281 WEDGE 3 1342285 UPPER BRACKET 4 1342261 BUSHING 5
More informationCABLE CUTTER INSTRUCTION MANUAL
INSTRUCTION MANUAL For additional copies at no charge order 999 6443.0 750 CABLE CUTTER Read and understand all of the instructions and safety information in this manual before operating or servicing this
More informationRAS-5E PART NO Date: 04/08/02
33-400, 33-401, 33-402, 33-403 14 RADIAL SAWS 33-410, 33-411, 33-412, 33-413 16 RADIAL SAWS 33-420, 33-421, 33-422, 33-423 18 RADIAL SAWS RAS-5E PART NO. 424-03-651-0018 Date: 04/08/02 Page1/ RAS-5E /DEB
More informationK&T Saw Shop or
11-600030 MAC 2-10PS 04/67 to 11/67 IPL 84288 Page 1 of 25 Accessories www.ktoutdoor.com 11-600030 MAC 2-10PS 04/67 to 11/67 IPL 84288 Page 2 of 25 Accessories 83434 Manual - Owner's 62827 Wrench - Screwdriver
More informationBUSH HOG LAND MAINTENANCE REPAIR PARTS MANUAL MODEL: 280 SERIES SECTION: 59
BUSH HOG LAND MAINTENANCE REPAIR S MANUAL MODEL: 0 SERIES SECTION: P.O. Box 0 Selma, AL 0-0 () - () -00 Parts Ordering -00-0- Fax -00-- www.bushhog.com BUSH HOG/ LAND MAINTENANCE REPAIR S MANUAL JUNE,
More information633010A 36" Fixed Deck 15HP Gear Drive Assembled Page 1 of 30 Baffles
633010A 36" Fixed Deck 15HP Gear Drive Assembled Page 1 of 30 Baffles 633010A 36" Fixed Deck 15HP Gear Drive Assembled Page 2 of 30 Baffles Ref # Part Number Qty Description 1 64018-2 2 BLT-CRG 1/4-20X3/4
More informationTECHNICAL DATA BROCHURE ZTR 308/3II
Date 8/84 Page 1 of 6 TECHNICAL DATA BROCHURE ZTR 308/3II IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATION OR MAKING ADJUSTMENTS. ' Seat Adjustment Loosen bolts on sliding brackets under each side of
More informationPRODUCT USE INFORMATION
921545200 *54520BAG1* 54520BAG1 Thank you for choosing Rough Country for all your suspension needs. 2009-17 Ford F150 3 Suspension Kit Rough Country recommends a certified technician install this system.
More informationCATALOG OF REPLACEMENT PARTS SLICERS (INCLUDES MOTOR PARTS) A product of HOBART CORPORATION 701 S. RIDGE AVENUE TROY, OHIO
CATALOG OF REPLACEMENT PARTS SLICERS (INCLUDES MOTOR PARTS) 2912PS 2912SC ML-104966 ML-104965 A product of HOBART CORPORATION 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 FORM 34655 (Apr. 2001) 7-8-9-10 5-6
More informationParts Catalog. WYRZ46XS/50XL/60XL Residential Zero Turn Mower. Table of Contents
Table of Contents Parts Catalog R WYRZ46XS/50XL/60XL Residential Zero Turn Mower Worldlawn Power Equipment, Inc. 401 N. Commerce Street, Beatrice, NE 68310 Toll Free Number: 1-800-267-4255 Table of Contents
More informationWYS48FX730VLCA WYS52FX730V WYS52FX730VCA
PARTS MANUAL WYS48FX730VL WYS48FX730VLCA WYS52FX730V WYS52FX730VCA 2 WORLDLAWN POWER EQUIPMENT, INC. WORLDLAWNPOWEREQUIPMENT.COM 401 COMMERCE STREET BEATRICE, NE 68310 800-267-4255 FAX 402-223-4103 3 4
More informationOPERATOR S MANUAL FABRIC 3-BAG GRASS CATCHER PART NO PRINTED 8/2012 PRINTED IN USA
OPERATOR S MANUAL FABRIC -BAG GRASS CATCHER Models: GC-STC-V This manual contains the operating instructions and safety information for your Scag mower accessory. Reading this manual can provide you with
More information320 Series Models 325, 326, 327
0 Series Models,, ROTARY MOWER Published 0/ PARTS MANUAL SECTION An Operator s Manual was shipped with the equipment. The Operator s Manual is an integral part of the safe operation of this machine and
More informationTECHNICAL DATA BROCHURE ZTR 426
TECHNICAL DATA BROCHURE ZTR 426 Date 8/84 IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATION. Page 1 of 6 Seat Adjustment Loosen bolts on sliding bracket under each side of seat, slide seat forward or
More informationDAKE / JOHNSON VERTICAL BAND SAW
DAKE / JOHNSON VERTICAL BAND SAW Model F - 6 INSTRUCTION MANUAL MODEL:F-6 SERIAL NUMBER: DATE PURCHASED: Need band saw blades? Call Dake DAKE (Division of JSJ) 724 Robbins Road Grand Haven, Michigan 4947
More informationWorldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE Toll Free Number:
Parts Catalog R Commercial WY48 Mower Worldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE 68310 Toll Free Number: 1-800-267-4255 Table of Contents Table of Contents Mower Assembly..
More informationLawn Edger Parts Manual
Lawn Edger Parts Manual Models 80 Lawn Edger 80 Lawn Edger 80 Lawn Edger CE 000D /0 Printed in USA THE MANUAL Before you operate your unit, carefully and completely read manuals supplied with the unit.
More information136R616G190 Lawn Tractor FST-16 (1996) Page 1 of 27 42" Mowing Deck
136R616G190 Lawn Tractor FST-16 (1996) Page 1 of 27 42" Mowing Deck 136R616G190 Lawn Tractor FST-16 (1996) Page 2 of 27 42" Mowing Deck 3 97600A 1 S 42" Deck Ass'y. Code: N notates a new part (not previously
More informationFLAIL MOWER SHREDDER
FLAIL MOWER SHREDDER Operation, Service, & Parts Manual For Models: GML41, 49, 61, 69, & 79 February 2006 FORM: GMLMower.QXD TABLE OF CONTENTS Installation....................................................1
More informationChain Box and Knife. Item # Description Part Number 180-D & GS
Chain Box and Knife Item # Description Part Number 180-D & GS 1 Groove pin 2275-03160 2 Hex cap screw 2175-03061 3 Washer 2275-03060 4 Setscrew 2175-07163 5 Chain box 4975-00355 6 Berkel logo 3175-00152
More informationQuadfloat 126 For Groundsmaster 455D
Form No. 3324 134 Quadfloat 126 For Groundsmaster 455D Model No. 30402 200000201 and Up Parts Catalog Ordering Replacement Parts To order replacement parts, please supply: the part number, the quantity,
More informationOLYMPIAN MODEL 740 Operation and Service Manual
OLYMPIAN MODEL 740 Operation and Service Manual P/N 133911-102 FCI MANUAL P/N 133865-001 Data herein has been verified and validated and believed adequate for the intended use. If the machine or procedures
More informationMitre Band Saw. Installation and Operating Instructions Note: Not all saw parts are shown in this booklet. Replaceable Aluminum Saw Table
P ARTS C ATALOG 2G PARTS CATALOG Drive Wheel End Pulley Box Speed Reducer M FG. COMPANY, INC. Mitre Band Saw Installation and Operating Instructions Note: Not all saw parts are shown in this booklet Motor
More informationKubota Rear Discharge Mowers 1.3m
Operating instructions and parts manual for Kubota Rear Discharge Mowers 1.3m (For G2160 Tractors) autoguide equipment Heddington, Nr Calne, Wiltshire, SN11 0PS Telephone: +44 (0) 1380 850885 Fax: +44
More informationHydrostatic Zero-Turn Commercial Riding Mower
Hydrostatic Zero-Turn Commercial Riding Mower Professional Turf Equipment 0" Fabricated Deck ILLUSTRATED PARTS LIST TABLE OF CONTENTS Frame Assembly.................................. 3 0" Fabricated Cutter
More informationJARVIS. Model 50G Hydraulic Dehorner
Hydraulic Dehorner EQUIPMENT SELECTION... Ordering No. TABLE OF CONTENTS... Page 50G Dehorner Electric Triggers Offset Blades... 4025011 Cup Blades... 4025047 Air Triggers Offset Blades... 4025025 Cup
More informationFORM NO Recycler /Rear Bagging. Walk Behind Mower. Model No & Up. Parts Catalog
FORM NO. 3322 771 21 Recycler /Rear Bagging Walk Behind Mower Model No. 20027 9900001 & Up Parts Catalog 3322 771 ORDERING REPLACEMENT PARTS To order replacement parts, please supply: the part number,
More informationMain Components Early Style
Pipe & Bolt Threading Machine Main Components Early Style * * 0 0 0 0 0 Service Notes: Ref. No.. Do not substitute bolt longer than / inches. Severe damage to Rear Bearing will result. Ref. No.. To assure
More informationMulching and Finishing Mowers MP and FP
Mulching and Finishing Mowers MP and FP Parts Manual Locke Turf 0 Highway E, Opp, Alabama, () -00 Transport Wheel, Tire & Spindle MP and FP ALPHABETICAL INDEX CONTENTS PAGE 00 Hydraulic Cylinder (Rear)
More information2720/12720 PARTS MANUAL 72A SECTION FLEX WING ROTARY MOWER
0/0 This Manual applies to models 0 and 0 that use a blade pan which measures. blade hole center to blade hole center. Also blades measure 8. from hole center to blade tip. See Section if these dimensions
More informationGLACIER PRO RANGER MID SIZE MOUNT KIT
GLACIER PRO RANGER MID SIZE MOUNT KIT P/N 2880261 APPLICATION FOR USE WITH THE GLACIER PRO MID SIZE PLOW SYSTEM (P/N 2880260) ON 2010 AND NEWER RANGER MID SIZE MODELS BEFORE YOU BEGIN Read these instructions
More informationAssembly and Parts Manual
Assembly and Parts Manual Detracker Manufacturing, Inc. www.greatplainsmfg.com Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow
More informationWEAVER JACK CORP. MASTER PARTS PRICE & IDENTIFICATION LIST. (517) Fax (517) MINIMUM BILLING $20.00
EFFECTIVE JULY 1, 2014 WEAVER JACK CORP. MASTER PARTS PRICE & IDENTIFICATION LIST (517) 263-6500 Fax (517) 263-2810 MINIMUM BILLING $20.00 THIS PRICE LIST SUPERSEDES ALL PREVIOUS PARTS PRICE LISTS (Prices
More informationRepair Manual and Spare Parts List
Hydraulic Drive Unit Type Techn. Doc. No. 362 and Accessories for Pipe Cutting Machine Darstellung kann vom Original abweichen Repair Manual and 580067000_Inst_en_Version_03 Repair General In general,
More informationJARVIS. Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner
Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner 30CL--1 Hock Cutter 30CL--1 Pistol Grip 30CL--3 Dehorner EQUIPMENT SELECTION... Ordering No. 30CL--1 Hock Cutter... 4025013 30CL--1 Hock Cutter with Grabber
More informationOPERATOR S MANUAL MODEL GC-STC-V
MODEL GC-STC-V THIS MANUAL CONTAINS THE OPERATING INSTRUCTIONS AND SAFETY INFORMA- TION FOR YOUR SCAG ACCESSORY. READ- ING THIS MANUAL WILL PROVIDE YOU WITH MAINTENANCE AND ADJUSTMENT PROCEDURES TO KEEP
More informationAssembly & Installation Instructions
TM P R O D U C T S Assembly & Installation Instructions FOR 28 SERIES SNOWPLOW PIVOT ASSEMBLY AND FLOAT LIMITER 99103000 FOR SERIAL NUMBERS 28D100000 TO 28D100770 97100552A 1. THINK SAFETY, ALWAYS WEAR
More information10" TABLE SAW Model
April 2001 INDUSTRIAL 10" TABLE SAW Model 06014739 4000 Open for Tool Illustration Pos. Part Number Description {Qty} F/C Pos. Part Number Description {Qty} F/C 1 2 0 996 864 Motor Housing 71 2 2 0 996
More informationWorldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE Toll Free Number:
Parts Catalog R Commercial / Residential 33 Mower Worldlawn Power Equipment, Inc. Industrial Park 2415 Ashland Ave. Beatrice, NE 68310 Toll Free Number: 1-800-267-4255 Table of Contents Table of Contents
More informationBUSH HOG LAND MAINTENANCE REPAIR PARTS MANUAL MODEL: TD-1100 SECTION: 66
BUSH HOG LAND MAINTENANCE REPAIR S MANUAL MODEL: TD-00 SECTION: 0 Griffin Ave. Selma, AL 0 () - () -00 Parts Ordering -00-0- Fax -00-- www.bushhog.com BUSH HOG/ LAND MAINTENANCE REPAIR S MANUAL JUNE, 00
More informationMaintenance and Repair
Maintenance and Repair WARNING ALWAYS shut off the engine, remove key from ignition, make sure the engine is cool, and disconnect the spark plug and positive battery terminal from the battery before cleaning,
More informationParts Manual for the Wright Z
Parts Manual for the Wright Z Serial numbers 40581 & Higher Check www.wrightmfg.com for the latest revision Rev 9/2007 Shown with OPTIONAL Grass Collection System 2006 Wright Manufacturing Inc., All Rights
More informationILLUSTRATED PARTS LIST THIS MANUAL CONTAINS THE ILLUSTRATED PARTS LIST FOR MODELS:
IPL MODEL SWZU 1 6 2 6 6 6 6 ILLUSTRATED PARTS LIST 0 2 6 8 THIS MANUAL CONTAINS THE ILLUSTRATED PARTS LIST FOR MODELS: SWZU6-1KA with a serial number of 260001 to 26 SWZU8-1KA with a serial number of
More informationRepair Parts Parts List for 13" Thickness Planer Model No. TP13001
Parts List for " Thickness Planer Model. TP00 Figure 0 Always order by Part Number - t by Number.. 0 00-0 0 0 - - 0- Cord w/plug * Screw Pan Hd M x 0.-0 Housing Switch Gasket Foam Motor (Includes Brushes)
More information25 Horsepower Hydrostatic Zero-Turn Commercial Riding Mower
MMZ 2, 260 2 Horsepower Hydrostatic Zero-Turn Commercial Riding Mower ILLUSTRATED PARTS LIST " Float Cutter Deck - Figure 1 3 1 27 32 17 6 1 11 31 36 3 19 7 23 1 33 38 18 37 22 3 20 2 10 2 12 21 30 39
More informationILLUSTRATED PARTS LIST THIS MANUAL CONTAINS THE ILLUSTRATED PARTS LIST FOR MODELS:
IPL MODEL SWZU 71 7 7 7 ILLUSTRATED PARTS LIST 70 7 THIS MANUAL CONTAINS THE ILLUSTRATED PARTS LIST FOR MODELS: SWZUA-KAI with a serial number of C00001 to C SWZUV-17KAI with a serial number of C00001
More information42 Rear Discharge Cutting Unit
FORM NO. 3319 728 Wheel Horse 42 Rear Discharge Cutting Unit Model No. 78353 8900001 & Up Model No. 78442 8900001 & Up Parts Catalog 3319 728 ORDERING REPLACEMENT PARTS To order replacement parts, please
More informationInstruction Manual and Parts List
Instruction Manual and Parts List KW Products Inc. Copyright 2003, All Rights Reserved Equipment, specifications, options and accessories subject to change without notice Part #108-3050-32 521 WARRANTY
More information126in Quadfloat Mower Groundsmaster 455 D
Form No. 3326-597 126in Quadfloat Mower Groundsmaster 455 D Model No. 30402 210000001 and Up Parts Catalog Ordering Replacement Parts To order replacement parts, please supply: the part number, the quantity,
More informationSharpener Assembly Parts List
Sharpener Assembly Parts List Item Description Part Number sharpener assy. w/o cover 4675-00851 N/S sharpener assy. w/ cover assy. no upper guard 4675-00853 **sharpener assy. w/ cover assy. & upper guard
More informationParts Manual DX272 / Please read the operator s manual carefully and make sure you understand the instructions before using the machine.
Parts Manual DX22 / 966651501 Please read the operator s manual carefully and make sure you understand the instructions before using the machine. Gasoline containing up to 10% ethanol (E10) is acceptable
More informationTHIS MANUAL CONTAINS THE ILLUSTRATED PARTS LIST FOR MODELS: GC-2B
ILLUSTRATED PARTS IPLMANUAL 0 0 FABRIC -BAG GRASS CATCHER Model GC-B THIS MANUAL CONTAINS THE ILLUSTRATED PARTS LIST FOR MODELS: GC-B with a serial number of M0000 to M 0 Scag Power Equipment Division
More informationEW32FS481V EW36FS481V EW48FS481V EW32FS481VCA EW36FS481VCA EW48FS481VCA
EW32FS481V EW36FS481V EW48FS481V EW32FS481VCA EW36FS481VCA EW48FS481VCA PARTS MANUAL ENCORE MANUFACTURING A DIVISION OF WORLDLAWN POWER EQUIPMENT, INC. ENCOREEQUIPMENT.COM 2415 ASHLAND AVE BEATRICE, NE
More informationParts Catalog. S-Series Slicer Standard Automatic S13A. Model:
, 08 99508 ECN 0 Parts Catalog S-Series Slicer Standard Automatic Model: SA SA 0/5/8/08 Rev. Y IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF UNIT.
More informationSINGLE WIDE MASTER CATALOG GOSS COMMUNITY UNIT GOSS COMMUNITY FOLDER
SINGLE WIDE MASTER CATALOG GOSS COMMUNITY UNIT GOSS (Click on the name to be taken to that section) Stocking Manufacturer of Quality Replacement Parts (815) 965-0884 Fax (815)965-1049 Welcome to the Quality
More informationFinishing Mower Estate 72
Finishing Mower Estate 72 Owners/Operators Manual & Spare Parts List Issue Date: October 2011 1 Introduction Your FIELDMASTER Estate 72 Finishing Mower has been designed to do a range of work to your satisfaction.
More informationPublished 10/12 SICKLE BAR BOOM MOWER PART'S MANUAL SECTION 90
Published 10/12 PT5/PT5-2 POWERTRIM SICKLE BAR BOOM MOWER PART'S MANUAL SECTION 90 PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase
More informationParts Catalog. S-Series Slicer Automatic. Model:
, 07 99509 ECN 077 Parts Catalog S-Series Slicer Automatic Model: SGA SGA 05/08/07 Rev. J IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF UNIT. GLOBE
More informationRacing Jack Max. Capacity: 3,000 lbs. (1,361 kg)
R SPX Corporation 655 Eisenhower Drive Owatonna, MN 55060-0995 USA Phone: (507) 455-7000 Tech. Serv.: (800) 533-6127 Fax: (800) 955-8329 Order Entry: (800) 533-6127 Fax: (800) 283-8665 International Sales:
More information1 MTD Dash Panel Support Brkt. 2 MTD Dash Panel 3 MTD Hex Bolt 5/16-18 x.75" Lg.* 4 MTD Bulb 5 MTD Hex AB-Tap
1 MTD 16655 Dash Panel Support Brkt. 2 MTD 16656 Dash Panel 3 MTD 710-0118 Hex Bolt 5/16-18 x.75" Lg.* 4 MTD 725-0963 Bulb 5 MTD 710-0776 Hex AB-Tap Scr. 1/4 x.62" 6 MTD 725-1058 Socket 7 MTD 712-0267
More informationParts Catalog. S-Series Slicer Standard Automatic S13A. Model:
, 07 99508 ECN 06 Parts Catalog S-Series Slicer Standard Automatic Model: SA SA //07 Rev. L IMPORTANT! TO EXPEDITE SHIPMENT OF PARTS, ALWAYS SPECIFY MODEL, REV, PART NUMBER, AND SERIAL NUMBER OF UNIT.
More informationOWNERS MANUAL. Model No LB. PUSH BROADCAST SPREADER. Assembly Operation Maintenance Repair Parts
OWNERS MANUAL Model No. 45-02102-101 SHIELD UP - 8 TO 18 FT. SPREAD WIDTH SHIELD DOWN - 3 TO 4 FT. SPREAD WIDTH 125 LB. PUSH BROADCAST SPREADER CAUTION: Read Rules for Safe Operation and Instructions Carefully
More informationTwo-Stage Snow Blower For 4WD Pick Up Trucks. Operator s Manual
Two-Stage Snow Blower For 4WD Pick Up Trucks Operator s Manual Distrubuted by: Metal Fabricating LLC P.O. Box 831 Brodheadsville, PA 18322 Phone: 570-992-9989 SnowVac.com WARRANTY POLICY Metal Fabricating
More informationBUSH HOG LAND MAINTENANCE REPAIR PARTS MANUAL MODEL: 405 / 406 SECTION: 17
BUSH HOG LAND MAINTENANCE REPAIR S MANUAL MODEL: 0 / 0 SECTION: 0 Griffin Ave. Selma, AL 0 () - () -00 Parts Ordering -00-0- Fax -00-- www.bushhog.com BUSH HOG/ LAND MAINTENANCE REPAIR S MANUAL SEPTEMBER,
More informationBlue Jay Rodless Cylinder BC MS. Track Repair Manual 1996 & 2012 THE EASTMAN EASTMAN. All End Caps Black for Models
EASTMAN 1996 & 2012 THE EASTMAN Blue Jay Rodless Cylinder BC-40224-MS Track Repair Manual All End Caps Black for 1996-2012 Models IMPORTANT Disconnect this equipment from pneumatic pressure lines before
More informationRepair Manual and Spare Parts List
Pneumatic Drive Unit Type Techn. Doc. No. 352 and Accessories for Pipe Cutting Machine Darstellung kann vom Original abweichen Repair Manual and 580027000_Inst_en_Version_02 Repair General In general,
More information