GL1200T Cut & Seal. (GL1200 Seal only)

Size: px
Start display at page:

Download "GL1200T Cut & Seal. (GL1200 Seal only)"

Transcription

1 GL INSTRUMENTS Technical Description & Operating Instructions Safe Seal Cut & Seal Welder for Filter Sacks GL1200T Cut & Seal (GL1200 Seal only) For industrial use only Important Safety & Operating Instructions Please read carefully and keep for future reference Based on the original design by Graham Lee Supplied by Capricorn Controls Limited Unit 1 9c, Thorpe Close Banbury, OX16 4SW, England T : +44 (0) (4 lines) F : +44 (0) E : sales@capricorn-controls.com W: Publication GL1200 Issue: 001 Dated: January 6th 2014

2 Technical Safety Information for the User This description contains the necessary information for the correct application of the product described below. It is intended for use by technically qualified personal only. Safety Instructions The following instructions are provided for the personal safety of operators and also for the protection of the described product and connected equipment.! Warning! Hazardous Voltage 230VAC if Control Box cover removed Failure to observe can Kill, cause serious injury or damage Isolate from mains before installation or dismantling work, fuse changes or replacement of spare parts. Observe the prescribed accident prevention and safety rules for the specific application. Before putting into operation check if the rated voltage for the unit conforms to the local supply voltage. The Control Box must be earthed at all times. On completion of the seal, the bars will be hot. The operator should take care to avoid contact with the heated surfaces and to store the top bar safely during this time. When choosing a working position it should be kept in mind that the standard machine is not sealed against the ingress of water or dust. Specified Use The units described herein are heat sealers for use in industrial applications. They are designed for use with polythene sheet or tubing and other similar materials. Contents Page User Safety information 2 Images of Major Parts Introduction Seal Control Module Operation Safety Maintenance Trouble Shooting, Repairs & Warranty Specification 8 Capricorn Controls Limited Page 2 of 8 GL1200 Issue: 001

3 Sealing Head assembly with toggle clamps shown open and the Top Bar removed Green Push-Button to activate Seal Cycle with Red Cycle LED to left of it Micro-Switch Magnet Top Bar with white Silicon Rubber Pressure Pad clearly visible Cable Entry CONTROL BOX - Front Control Box - Rear, showing Fuse Holder, Labels & cable entry Mains Lead with 230V 13A Plug 7-Pin Socket to connect Sealing Head Seal Controller (mounted behind protective door) Capricorn Controls Limited Page 3 of 8 GL1200 Issue: 001

4 1.0 Introduction The heat sealers described here are purpose designed for safe disposal of used filters in a wide range of applications and industries. They are semi-automatic in operation and no special operator skills are required. However, some adjustment is required to obtain the best results from the equipment, which is described below. Heat sealing of polythene tubing and similar materials is achieved by simultaneous application of heat and pressure. These machines operate on the impulse principal, which means that the seal bar is not continuously heated. On initiation of the sealing cycle, by momentarily pressing the green push-button, the Seal Control Module switches high current through the heating element for a brief period, typically a few seconds in duration. The Red LED (adjacent to the Green push-button) indicates that the Heat + Cool cycle is in operation. As soon as this LED extinguishes the weld is complete and the toggle clamps can be released to remove the top bar and the welded material. 2.0 Seal Control Module The SCM200 Seal Control Module, fitted in the Control Box, provides a simple system for setting the machine to seal a wide range of materials, and to accurately repeat those settings when subsequently required - simply by noting the numbers on the four thumb-wheel switches. Seal Time setting = representing 0-10 seconds (example 3 4 setting = approx. 3.4 seconds) Trim setting = Where 9 represents minimum compensation (factory set at 9 ). See below Cool Time setting = 0-9 representing 0-20 seconds (example 4 setting = approx. 8 seconds) Note: The above timings are only approximate but they there repeatable. Note: Always record the four numbers for future use (i.e in this example) Trim Setting This simulates the amount of heat retained in the bars to automatically shorten the second and subsequent Seal Times. Assuming there will be some considerable time between Seals, this is factory set at 9 for effectively no compensation (no heat retained). If adjustment is required, we recommend reducing by one number at a time and doing two or three test seals at the required interval. Capricorn Controls Limited Page 4 of 8 GL1200 Issue: 001

5 3.0 Operation The machine consists of a Control Box and separate Sealing Head. See page 3 CONTROL BOX Power Transformer to provide high current at low voltage to the heating element. Protection Fuse accessed from the rear of the unit, to protect the Transformer primary winding. SCM200 Seal Control Module to set repeatable Seal, Trim and Cool times. Power relay to switch the high current supply to the Heater Bar. 7-pin power socket to connect control circuits and high current supply, to the Sealing Head. Please order for 115V or 230V operation As standard, 230V units include an integral 1.4 metre mains lead with moulded UK 13A Plug. As standard, 115V units include an integral 1.4 metre mains lead with un-fused 32A IP44 Industrial Plug. SEALING HEAD Base assembly with Heating Bar, Green Push-Button, Red Seal Cycle LED, 2.6 metre cable with 7-pin plug. Top Bar with handles, micro-switch magnet and silicon rubber Pressure Pad. 3.1 Preparation of Machine Plug the Sealing Head 7-Pin connector into the mating half on the Control Box, remove the Top Bar and place this in a clean and safe place. Do not plug into the mains supply at this time. Note: It is very important that the machine is NOT stored with the Top Bar clamped, as this will damage the Silicon Rubber pressure pad. 3.2 Preparation of Filter Bag for Sealing Isolate from the Mains Supply. Lay the Filter Bag across the Bottom (Sealing) Bar ensuring that the bag lies flat and is free from creases and folds. Replace the Top Bar and secure using both Toggle Clamps. The Bag is now ready for Sealing. 3.3 Sealing Operation Connect the Control Box to a mains supply and the Red Power LED should light in the display window. Press the Green push-button on the Sealing Head and the adjacent Red LED should light, indicating that the Sealing Cycle is in progress (additional LEDs in the window on the Control Box will also indicate the separate Seal and Cool times within the Seal Cycle). When the Red LED on the Seal Head extinguishes, the Seal cycle has finished. Switch off the mains supply and release the toggle clamps to remove the Top Bar and Filter Sack. It is strongly recommended that prior to doing a safe change of a contaminated filter, the operator does a sample seal to ensure that the seal is satisfactory for that material. Remember to record the Thumbwheel switch positions for future use. Capricorn Controls Limited Page 5 of 8 GL1200 Issue: 001

6 4.0 Safety While connected to the mains supply, the machine contains parts that are electrically Live. The electrical supply MUST be disconnected prior to removal of the control box cover. A competent Electrician must carry out any repair or test work, or alternatively the machine should be returned to the supplier. The machine is fitted with a mains supply fuse, accessible at the rear of the Control Box, to protect the transformer s primary winding. The machine is also fitted with a mains lead and moulded 13A plug on the 230VAC version and with an unfused 32A IP44 3-pole Industrial Plug on the 110VAC version. The Control Box must be earthed. The machine incorporates several features to help ensure operator safety - a) The source of the heating current is isolated from the mains supply and is at a safe low voltage. b) For the machine to operate, the Sealing Head must be plugged into the Control Box. c) The top bar must be fitted and secured by the toggle clamps. d) To initiate the Seal cycle, press the green push-button for approx. 1 sec and the adjacent Red LED will light. e) The Red LED extinguishes to indicate that the Seal Cycle is complete and the Top Bar and material can be removed WARNING: - Immediately after the seal cycle has completed, the bars will be hot. The operator should avoid contact with heated surfaces and in particular when removing the top bar and sealed material. Ensure that the top bar is placed safely. WARNING: - When choosing a working position, it should be noted that the machine as a whole is not sealed against the ingress of water or dust. However, a dust proof door assembly is fitted to the Seal Controller to protect the Thumb-Wheel switches. 5.0 Maintenance 5.1 Mechanical The design and construction of the machine makes regular mechanical lubrication and maintenance unnecessary. Keep the Teflon fabric cover over the heating element clean and free of contamination Keep the silicon rubber Pressure Pad free from contamination and NEVER store the sealer clamped 5.2 Cover Tape and Heating Element The seal bars, both heated and unheated, will require attention at intervals, dependant on factors such as workload, material thickness and temperature. Bars in good condition will produce seals of constant width throughout the entire length and will exhibit a clear impression of the texture of the Teflon cover tape. If the seal quality is unsatisfactory, check the bar condition as follows, ensuring that only manufacturer s approved materials are used. Examine the Silicon Rubber and replace if required Examine the Teflon cover tape for cracks, surface defects or burn marks. Please contact the supplier or Manufacture for guidance as the Teflon cover tape cannot be replaced without dismantling the Sealing Head. Capricorn Controls Limited Page 6 of 8 GL1200 Issue: 001

7 6.0 Trouble Shooting SYMPTOM CHECK Machine inoperative, no LEDs Lit Mains Supply, Plug Fuse and Control Box fuse Supply LED Lit, machine inoperative 7-Pin Plug secure Polythene or similar material correctly positioned Top Bar correctly fitted and Toggle Clamps closed Green Push-Button pressed for 1 second Still no response or Heat & Cool LEDs flash momentarily Micro-switch and SCM200 Controller Thumb-wheel settings No improvement SCM200 Controller Note: Contact the Supplier or Manufacturer for Technical Support before attempting a repair 6.1 Repairs & Servicing Spare parts do not normally include Teflon Tape or Heater Strips as changing these necessitates disassembly of the Seal Head and we recommend service exchange on all major items GL-CB1 = Control Box complete GL-SCM200 = Seal Controller only GL1200-TB1 = Top Bar only GL1200-SH1 = Seal Head complete with Seal only Heater Strip GL1200T-SH1 = Seal Head complete with Cut & Seal Heater Strip GL-SR1 = Silicon Rubber strip (supplied by the metre) However, if you have the necessary skilled personal and prefer do maintenance and out of warranty repairs, the required information and parts list is available on request. 6.2 Warranty Contact the supplier for Warranty claims, spares and Service Exchange parts. In addition to our standard Terms & Conditions of Supply, the conditional Warranty on this product excludes Teflon, Heating Elements and Silicon Rubber. Capricorn Controls Limited Page 7 of 8 GL1200 Issue: 001

8 7.0 Specification Rated Voltage (230V version) Rated Voltage (115V version) Operating Frequency Supply Burden Mains Plug Fuse Rear Fuse (Motor Rated) On Load Output Open Circuit Output nominal V nominal V nominal 50 / 60Hz 600VA Transformer 13A (230V) Only 10A (230V); 20A (115V) 44A at 35VAC intermittent rated at 1 : 3 duty cycle 45VAC Absolute Maximum Seal Length 1270 mm Overall Dimensions (mm) Control Box Sealing Head Net Weights Control Box Sealing Head 380d x 230w x 260 h (incl. feet and handle) 1555 length x 140 h (Toggle clamp levers, Down) 1525 length x 200 h (Toggle clamp levers, Up) 76 wide but allow 120 with cable exit 9.6 Kg 7.3 Kg Dimensions and weights are approximate. 7.1 Ordering Information GL1200T-115 GL1200T VAC : Seal & Cut Heat Seal Welder for Filter Sacks 230VAC : Seal & Cut Heat Seal Welder for Filter Sacks GL GL VAC : as GL1200T but Seal Only, no Cut 230VAC : as GL1200T but Seal Only, no Cut Manufactured in England and Distributed world-wide by Capricorn Controls Limited Unit 1 9c, Thorpe Close Banbury, OX16 4SW, England Tel: +44 (0) (4 lines) Fax: +44 (0) sales@capricorn-controls.com Web: Capricorn Controls Limited Page 8 of 8 GL1200 Issue: 001

GL1200T Cut & Seal. (GL1200 Seal only)

GL1200T Cut & Seal. (GL1200 Seal only) GL INSTRUMENTS & Operating Instructions Safe Seal Cut & Seal Welder for Filter Sacks GL1200T Cut & Seal (GL1200 Seal only) For industrial use only Important Safety & Operating Instructions Please read

More information

PSM72H Push-Button Start Module

PSM72H Push-Button Start Module Capricorn Controls DA02PSM72H1-2 Data & Application Note Page 1 of 6 PSM72H Push-Button Start Module Genset Controls - Timers/Monitors/Trips - Battery Charging Spares & Accessories - Custom Products Ultra

More information

SDM72 Start on Demand Modules

SDM72 Start on Demand Modules Capricorn Controls DA04SDM72-2 Revised Design Page 1 of 6 SDM72 Start on Demand Modules Genset Controls - Timers - Monitors - Trips - Battery Charging - Spares & Accessories - Custom Products Application

More information

REVISED ATM72 Auto Transfer Module

REVISED ATM72 Auto Transfer Module Capricorn Controls DA01ATM1-1 Data & Application Note Page 1 of 8 REVISED - - - ATM72 Auto Transfer Module Genset Controls - Timers - Monitors - Trips - Battery Charging - Spares & Accessories - Custom

More information

Installation manual wall-mounted distributor

Installation manual wall-mounted distributor EN Installation manual wall-mounted distributor EN 60003233 Issue 11.2016 2016-14-11 Table of contents 1 About this manual 3 1.1 Structure of the warnings 3 1.2 Symbols used 4 1.3 Signal words used 4 2

More information

BVF300 'Special' Battery Voltage Monitor

BVF300 'Special' Battery Voltage Monitor CAPRICORN CONTROLS DATA & APPLICATION NOTE Page 1 of 6 Data & Application Notes BVF300 'Special' Battery Voltage Monitor Control Systems - Genset Controls - Timers/Monitors/Trips - Battery Chargers - Custom

More information

MAKING MODERN LIVING POSSIBLE INT. Danfoss Link HR Hidden Relay. Installation Manual. Danfoss Heating

MAKING MODERN LIVING POSSIBLE INT. Danfoss Link HR Hidden Relay. Installation Manual. Danfoss Heating MAKING MODERN LIVING POSSIBLE INT Danfoss Link HR Hidden Relay Installation Manual Danfoss Heating devireg 550 22.0 22.0 devireg 550 Danfoss Link HR The Danfoss Link HR (Hidden Relay) is a device for switching

More information

INSTRUCTION MANUAL FOR THE THERMOCOUPLE ATTACHMENT UNIT (TAU)

INSTRUCTION MANUAL FOR THE THERMOCOUPLE ATTACHMENT UNIT (TAU) INSTRUCTION MANUAL FOR THE THERMOCOUPLE ATTACHMENT UNIT (TAU) Model Number: 41756 (100 125Vac) 41757 (220 240Vac) Manufactured in the United Kingdom CONTENTS Chapter Page Specification 3 What the TAU does

More information

Installation manual portable distributors

Installation manual portable distributors EN Installation manual portable distributors EN 60003206 Issue 11.2016 15/11/2016 Table of contents 1 About this manual 3 1.1 Structure of the warnings 3 1.2 Symbols used 4 1.3 Signal words used 4 2 Intended

More information

I1 7.5 Pre-Lit Clear Christmas Tree

I1 7.5 Pre-Lit Clear Christmas Tree I1 7.5 Pre-Lit Clear Christmas Tree 62432-13 INSTRUCTION MANUAL Thank you for purchasing this Pre-lighted Tree. This tree assembles in minutes and is decorated with UL listed miniature light sets. Please

More information

KENSUN HID AUTOMOTIVE HEAD LAMP CONVERSION KIT INSTALLATION MANUAL

KENSUN HID AUTOMOTIVE HEAD LAMP CONVERSION KIT INSTALLATION MANUAL 1 KENSUN HID AUTOMOTIVE HEAD LAMP CONVERSION KIT INSTALLATION MANUAL 2 CONTENTS A. Before Installing B. Installing the Bulbs C. Installing the Ballasts D. For Bi Xenon Only: Installing the Relay Harness

More information

SUM340 SUMMATION BOARD

SUM340 SUMMATION BOARD Capricorn Controls Data & Application Note Page 1 of 6 SUM340 SUMMATION BOARD Genset Controls - Timers/Monitors/Trips - Battery Charging Spares & Accessories - Custom Products The SUM340 Summation Board

More information

LED Emergency Luminaires

LED Emergency Luminaires LED Emergency Luminaires THIS FITTING SHOULD NOT BE USED IN AREAS EXCEEDING 25 C AMBIENT AIR TEMPERATURE This fitting must be installed by a qualified electrician and wired in accordance with the latest

More information

Fitting Instructions: Street Triple from VIN and Street Triple R from VIN A

Fitting Instructions: Street Triple from VIN and Street Triple R from VIN A English Fitting Instructions: Street Triple from VIN 560477 and Street Triple R from VIN 560477 A9808113 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of

More information

Rescue Pac. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference

Rescue Pac. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference Please dispose of Packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

OPERATION INSTRUCTIONS

OPERATION INSTRUCTIONS www.r-techwelding.co.uk Email: sales@r-techwelding.co.uk Tel: 01452 733933 Fax: 01452 733939 ProArc 175 INVERTER ARC WELDER OPERATION INSTRUCTIONS Version 2017-10 2 3 Thank you for selecting the R-Tech

More information

Ezyfit AC Controller INSTRUCTION BOOK 2 & 4 STATION UNITS

Ezyfit AC Controller INSTRUCTION BOOK 2 & 4 STATION UNITS Ezyfit AC Controller INSTRUCTION BOOK 2 & 4 STATION UNITS Features This unit is available in two and four station configurations. Designed for residential applications, this controller has an individual

More information

Operators Guide: RoboSign Stop/Go Traffic Control System

Operators Guide: RoboSign Stop/Go Traffic Control System Operators Guide: RoboSign Stop/Go Traffic Control System RoboSign Remote controlled Stop/Go temporary traffic control system Operators Guide NZTA Conditions - Automated Stop/Go Traffic Control System NZTA

More information

10A / 15A / 20A Solar Charge Controller. PU1024 / PU1524 / PU2024 series INSTRUCTION MANUAL

10A / 15A / 20A Solar Charge Controller. PU1024 / PU1524 / PU2024 series INSTRUCTION MANUAL 10A / 15A / 20A Solar Charge Controller PU1024 / PU1524 / PU2024 series INSTRUCTION MANUAL Dear Customer, Thank you very much for choosing our product. This manual contains important information about

More information

CD100 Series. Operators Manual SINGLE COLUMN CARD DISPENSER

CD100 Series. Operators Manual SINGLE COLUMN CARD DISPENSER CD100 Series SINGLE COLUMN CARD DISPENSER Operators Manual Contents 1 Specifications...1 2 Installation...2 2.1 Unpacking and inspection...2 2.2 Installation...2 2.3 Electrical Connections...2 2.4 Initial

More information

MANUFACTURED IN THE UK

MANUFACTURED IN THE UK The Trojan range of energy efficient bulkhead fittings are manufactured with a polycarbonate base and diffuser. Together with a poured gasket the Trojan leads vandal-resistant IP65 technology. With a hinged

More information

Doc Ref: WD027/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No

Doc Ref: WD027/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No Icebreaker is an ultra slim 2D luminaire at home in many IP44 applications. Ideally suited for bathrooms and utility areas, and most widely preferred in social and key worker housing and student accomodation.

More information

28W WORK LAMP Model: CTL28 Part No:

28W WORK LAMP Model: CTL28 Part No: 28W WORK LAMP Model: CTL28 Part No: 4002905 INSTRUCTION MANUAL GC0609 INTRODUCTION Thank you for purchasing this CLARKE 28W Work Lamp. Before attempting to use the product, it is essential that you read

More information

Model Voltage Wattage Length Width Height Width Length 7J J

Model Voltage Wattage Length Width Height Width Length 7J J Please read and save these instructions. Read carefully before attempting to operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply

More information

Serial N... MX1 Chain Driven Pipe Cutting and Bevelling Machine Parts and Operating Manual

Serial N... MX1 Chain Driven Pipe Cutting and Bevelling Machine Parts and Operating Manual Serial N... MX1 Chain Driven Pipe Cutting and Bevelling Machine Parts and Operating Manual Table of contents Section Description Page 1.0 General Information 2 2.0 Specification 2 2.1 General Specification

More information

TM-1620 OPERATING INSTRUCTIONS AND OWNERS MANUAL

TM-1620 OPERATING INSTRUCTIONS AND OWNERS MANUAL TM-1620 OPERATING INSTRUCTIONS AND OWNERS MANUAL tracopackaging.com 800-284-WRAP 620 SOUTH 1325 WEST OREM, UT. PHONE 800-284-WRAP (9727) IMPORTANT: READ ALL INSTRUCTIONS BEFORE OPERATING EQUIPMENT Your

More information

POWER PINNER HAND WELDER 7200 OPERATOR S MANUAL

POWER PINNER HAND WELDER 7200 OPERATOR S MANUAL POWER PINNER HAND WELDER 7200 OPERATOR S MANUAL Copyright: January 5, 2009 Revised: November 24, 2014 Serial No. 0901189 - Gripnail Corporation An Employee Owned Company 97 Dexter Road East Providence,

More information

Doc Ref: WD024/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No

Doc Ref: WD024/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No The Galileo II range of decorative, wall or ceiling mounted luminaires, are as versatile as they are attractive. The range is available in two body sizes, 350mm and 425mm diameter, and in a variety of

More information

Operating Instructions For The X-Seal Manual Thermal Sealer

Operating Instructions For The X-Seal Manual Thermal Sealer Operating Instructions For The X-Seal Manual Thermal Sealer Version 1 Release 1 May 2009 FluidX Ltd. FluidX Ltd. Monks Heath Hall, Chelford Road, Nether Alderley, Cheshire, SK10 4SY, UK. T: +44(0) 1625

More information

EdgeLED TM Range. Installation and Operating Instructions EdgeLED TM RANGE INSTALLATION NON-EMERGENCY LUMINAIRES PRE INSTALLATION

EdgeLED TM Range. Installation and Operating Instructions EdgeLED TM RANGE INSTALLATION NON-EMERGENCY LUMINAIRES PRE INSTALLATION EdgeLED TM Range THIS FITTING SHOULD NOT BE USED IN AREAS EXCEEDING 25 C AMBIENT AIR TEMPERATURE This fitting must be installed by a qualified electrician and wired in accordance with the latest edition

More information

INFINITY-1 HALOGEN LIGHT BAR INSTALLATION MANUAL 7000 SERIES

INFINITY-1 HALOGEN LIGHT BAR INSTALLATION MANUAL 7000 SERIES INFINITY-1 HALOGEN LIGHT BAR INSTALLATION MANUAL 7000 SERIES Your purchase of a Wolo warning light is the perfect choice to compliment your vehicle. Wolo s warning lights are manufactured with the finest

More information

INFINITY-3 STROBE LED BAR INSTALLATION MANUAL 7700 SERIES

INFINITY-3 STROBE LED BAR INSTALLATION MANUAL 7700 SERIES INFINITY-3 STROBE LED BAR INSTALLATION MANUAL 7700 SERIES Your purchase of a Wolo warning light is the perfect choice to compliment your vehicle. Wolo s warning lights are manufactured with the finest

More information

TOPAZ 12 WALL PACK INSTALLATION & MAINTENANCE GUIDE (Part # LIT A)

TOPAZ 12 WALL PACK INSTALLATION & MAINTENANCE GUIDE (Part # LIT A) TOPAZ 12 WALL PACK INSTALLATION & MAINTENANCE GUIDE (Part # LIT-29499-1A) Contractor: Please read these instructions before starting installation. After installation, please forward this guide to the user

More information

Pro Booster 802Li. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference.

Pro Booster 802Li. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

Operating Instructions

Operating Instructions Important Information: These instructions contain safety information, read and follow them carefully. Dialight will not accept any responsibility for injury, damage or loss which may occur due to incorrect

More information

User Manual Rittal PMC UPS 6kVA

User Manual Rittal PMC UPS 6kVA User Manual Rittal PMC UPS 6kVA Germany Rittal GmbH & Co. KG Auf dem Stützelberg D-35745 Herborn Tel.: ++49-27 72-5 05-0 Fax: ++49-27 72-5 05-23 19 Internet: www.rittal.de 26 Contents 1. Introduction...

More information

KD1E Range Potential Indicators

KD1E Range Potential Indicators KD1E Range Potential Indicators Operating Instructions 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Limited Warranty & Limitation

More information

24V 3A EN54 Ancillary Power Supply

24V 3A EN54 Ancillary Power Supply 24V 3A EN54 Ancillary Power Supply Normal supply - green light on Fault condition - call Engineer Control relay - activated 3A Power Supply C-TEC Manufactured in England by C-Tec EN 54-4 : 1997 INSTALLATION

More information

VADA - V60-J PRODUCT OVERVIEW CONSTRUCTION MOTOR USAGE LIMITATIONS WARRANTY

VADA - V60-J PRODUCT OVERVIEW CONSTRUCTION MOTOR USAGE LIMITATIONS WARRANTY PRODUCT OVERVIEW The VADA series of self priming jet pumps combine the functional benefits of centrifugal pumps and the practical and qualitative benefits of self-priming pumps. The Venturi system the

More information

EASY CHARGE Waterproof portable Battery Charger

EASY CHARGE Waterproof portable Battery Charger EASY CHARGE Waterproof portable Battery Charger 1.1 AND 4.3 AMP MODELS EN NL, DE, FR, ES, IT USER S MANUAL WWW.MASTERVOLT.COM/EASYCHARGE-PORTABLE 10000009117/04 2 EN / EasyCharge 1.1 and 4.3 Amp - User

More information

Roller Door Operator

Roller Door Operator INSTALLATION INSTRUCTIONS AND OWNERS MANUAL Roller Door Operator IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO COMMENCING THE INSTALLATION OF THE OPERATOR UNIT CAUTION This Automatic Opener

More information

4 & 6 Zone 20A Controller Installation And Operating Manual

4 & 6 Zone 20A Controller Installation And Operating Manual UBE 4 & 6 Zone 20A ontroller Installation And Operating Manual Introduction Thank you for purchasing this ube 4 or 6 controller. Whilst the ube has been designed to be as simple as possible to install

More information

SELF PRIMING CHEMICAL SERVICE PUMPS

SELF PRIMING CHEMICAL SERVICE PUMPS SELF PRIMING CHEMICAL SERVICE PUMPS INSTALLATION AND OPERATING INSTRUCTIONS This Manual covers: SELF PRIMING MODEL RANGE J50ECX TO J250ECX STAINLESS STEEL*, and NON METALLIC SEAL PUMP MODEL: SERIAL NO:

More information

MANUFACTURED IN THE UK

MANUFACTURED IN THE UK The Galileo II range of decorative, wall or ceiling mounted luminaires, are as versatile as they are attractive. The range is available in two body sizes, 350mm and 425mm diameter, and in a variety of

More information

Owners Manual: - Pumps

Owners Manual: - Pumps Owners Manual: - Pumps GENERAL SAFETY RULES 1. The products mentioned in this manual are specially designed for the pre-filtering and re-circulation of water in swimming pools and spas. 2. They are designed

More information

Uninterruptible power supply Supply MEg101.4

Uninterruptible power supply Supply MEg101.4 Uninterruptible power supply Supply MEg101.4 MEgA Měřící Energetické Aparáty, a.s. 664 31 Česká 390 Czech Republic Uninterruptible power supply Supply MEg101.4 Uninterruptible power supply MEg101.4 1/

More information

POWERLINE 2000 Energy Management System TM

POWERLINE 2000 Energy Management System TM Display Panel TM The PowerLine 00 EMS is a specialized power distribution and energy management system intended to be used in recreational vehicles. The Control Module is housed in the standard main distribution

More information

Industrial flue gas probes. Instruction manual

Industrial flue gas probes. Instruction manual Industrial flue gas probes Instruction manual 2 1 Contents 1 Contents 1 Contents... 3 2 Safety and the environment... 4 2.1. About this document... 4 2.2. Ensure safety... 4 2.3. Protecting the environment...

More information

Installation and Maintenancee Manual

Installation and Maintenancee Manual Installation and Maintenancee Manual Commercial Boom Gate Operator Model: GDS BOOM 4 and 6 A.B.N. 62 059 806 405 Nov 2013 Section No: CONTENTS Page Number: 1 Safety Precautions 3 2 Specifications 4 3 Mechanical

More information

SUBMERSIBLE WATER PUMPS

SUBMERSIBLE WATER PUMPS SUBMERSIBLE WATER PUMPS Model Nos. CS85S - CS85SA CS120S - CS120SA CS185S - CS185SA CS240S - CS240SA CS305S - CS305SA OPERATING & MAINTENANCE INSTRUCTIONS 1000 CONTENTS Warranty conditions... 3 Safety

More information

HALOGEN FLOODLIGHTS Models CHL1260C & 1260T Part Nos: &

HALOGEN FLOODLIGHTS Models CHL1260C & 1260T Part Nos: & HALOGEN FLOODLIGHTS Models CHL1260C & 1260T Part Nos: 5460600 & 5460595 OPERATING & MAINTENANCE INSTRUCTIONS GC0610 INTRODUCTION Thank you for purchasing this CLARKE Halogen Floodlight. Before attempting

More information

icebreaker icebreaker A C G GE Lighting 2D lamps are fitted as standard. I44

icebreaker icebreaker A C G GE Lighting 2D lamps are fitted as standard. I44 Icebreaker is an ultra slim 2D luminaire at home in many IP44 applications. Ideally suited for bathrooms and utility areas, and most widely preferred in social and key worker housing and student accomodation.

More information

HR25 Solo. Installation and User Instructions. Through the Wall Heat Recovery Ventilators

HR25 Solo. Installation and User Instructions. Through the Wall Heat Recovery Ventilators abc GB HR25 Solo Installation and User Instructions Models:- HR25 Solo HR25 Solo L HR25 Solo H HR25 Solo LH Through the Wall Heat Recovery Ventilators PLEASE READ INSTRUCTIONS IN CONJUNCTION WITH ILLUSTRATIONS.

More information

Instruction Manual PC104/PC105 3-PHASE SOCKET TESTER. Check out what else you can get from Martindale:

Instruction Manual PC104/PC105 3-PHASE SOCKET TESTER. Check out what else you can get from Martindale: Check out what else you can get from Martindale: 17th Edition Testers Accessories Calibration Equipment Continuity Testers Electricians Kits Environmental Products Full Calibration & Repair Service Fuse

More information

Instruction Manual & Specification

Instruction Manual & Specification SP200, SP400 & VP400 Proving Units Instruction Manual & Specification VP400 SP200 SP400 SS0019V2 Sn 1. Safety 1.1 Equipment Markings Caution - refer to the instruction manual Construction is double insulated

More information

IRRIGATION CONTROLLER

IRRIGATION CONTROLLER IRRIGATION CONTROLLER 4 and 6 Station Model INSTRUCTION MANUAL SUITABLE FOR INDOOR USE ONLY OTHERWISE WARRANTY IS VOID N10372 Table Of Contents Features 1 Glossary 2 Programming Instructions Introduction

More information

2D products are warranted for one year, the expected life of the ballast and/or Emergency module is 5 years

2D products are warranted for one year, the expected life of the ballast and/or Emergency module is 5 years 2D products are warranted for one year, the expected life of the ballast and/or Emergency module is 5 years The Trojan range of energy efficient bulkhead fittings are manufactured with a polycarbonate

More information

Sieve Shaker 200mm/300mm - 8/12 inch SV003

Sieve Shaker 200mm/300mm - 8/12 inch SV003 Sieve Shaker 200mm/300mm - 8/12 inch SV003 CONTENTS Introduction Specification Installation Controls Operation Maintenance Spares and Accessories 1 Introduction The unique action of this Sieve Shaker (Fig

More information

TYPE 5867 PORTABLE Q METER

TYPE 5867 PORTABLE Q METER IMPORTANT: Please read these instructions carefully before operating instrument SUBJECT TO CHANGE WITHOUT NOTICE This manual superseded all previous versions please keep for future reference TINSLEY, A

More information

Compact System NRGS 11-2 NRGS Original Installation Instructions English

Compact System NRGS 11-2 NRGS Original Installation Instructions English Compact System NRGS 11-2 NRGS 16-2 EN English Original Installation Instructions 810366-05 1 Contents Important Notes Page Usage for the intended purpose...4 Safety note...4 LV (Low Voltage) Directive

More information

INSTRUCTION MANUAL CM95/ CM100 TRUE RMS FLEXIBLE CLAMP METER. 1. SAFETY INFORMATION: Always read before proceeding. REMEMBER: SAFETY IS NO ACCIDENT

INSTRUCTION MANUAL CM95/ CM100 TRUE RMS FLEXIBLE CLAMP METER. 1. SAFETY INFORMATION: Always read before proceeding. REMEMBER: SAFETY IS NO ACCIDENT CM95/ CM100 TRUE RMS FLEXIBLE CLAMP METER INSTRUCTION MANUAL 1. SAFETY INFORMATION: Always read before proceeding. REMEMBER: SAFETY IS NO ACCIDENT These instructions contain both information and warnings

More information

MODEL 540 USER MANUAL INCORPORATING MODEL 530 TEMPERATURE CONTROLLER

MODEL 540 USER MANUAL INCORPORATING MODEL 530 TEMPERATURE CONTROLLER MODEL 540 USER MANUAL INCORPORATING MODEL 530 TEMPERATURE CONTROLLER Signal Group Limited 12 Doman Road, Camberley Surrey, GU15 3DF England Tel: +44 (0) 1276 682841 Fax: +44 (0) 1276 691302 e-mail: instruments@signal-group.com

More information

PHASE CONVERTERS OPERATING & MAINTENANCE INSTRUCTIONS. MODEL NO: PC40 and PC60. PART Nos:

PHASE CONVERTERS OPERATING & MAINTENANCE INSTRUCTIONS. MODEL NO: PC40 and PC60. PART Nos: PHASE CONVERTERS MODEL NO: PC40 and PC60 MODEL PART No: NO: 6012805 PC20 and PC40 6012810 PC60 PART Nos: 6012800 6012805 6012810 OPERATING & MAINTENANCE INSTRUCTIONS 0107 Specifications PC20 PC40 PC60

More information

AVIATOR REMOTE CONTROL HELICOPTER

AVIATOR REMOTE CONTROL HELICOPTER AVIATOR REMOTE CONTROL HELICOPTER THANK YOU. Thank you for your purchase of Protocol s Aviator Remote Control Helicopter. You are about to experience the best of what remote control flight has to offer.

More information

Installation and Operating Instructions Electric Vibrators HV/VFL Series

Installation and Operating Instructions Electric Vibrators HV/VFL Series Installation and Operating Instructions Electric Vibrators HV/VFL Series Original Instruction Würges Vibrationstechnik GmbH Daimlerstraße 9 D-86356 Neusäß Telephone +49 821 463081 Telefax +49 821 463084

More information

CONTENTS DIVERSE. Preface SQUEEZE ANALYSER SQA2 RESISTANCE WELDING FORCE MONITOR. Resistance Welding. Squeeze Analyser OPERATING INSTRUCTIONS

CONTENTS DIVERSE. Preface SQUEEZE ANALYSER SQA2 RESISTANCE WELDING FORCE MONITOR. Resistance Welding. Squeeze Analyser OPERATING INSTRUCTIONS DIVERSE SQUEEZE ANALYSER SQA2 RESISTANCE WELDING FORCE MONITOR OPERATING INSTRUCTIONS UK/US VERSION 2012 CONTENTS DIVERSE type SQA2 DIVERSE type SQA2 2 DESIGNED & MANUFACTURED BY:- DIVERSE TECHNOLOGIES

More information

Operators Guide: RoboSign Stop/Go Traffic Control System

Operators Guide: RoboSign Stop/Go Traffic Control System Operators Guide: RoboSign Stop/Go Traffic Control System RoboSign Remote controlled Stop/Go temporary traffic control system Operators Guide Table of Contents Operators Guide: RoboSign Stop/Go Traffic

More information

Lifting device for standard removable versions

Lifting device for standard removable versions Operating manual Lifting device for standard removable versions Type 1889 haacon hilft heben haacon hebetechnik gmbh Josef-Haamann-Str. 6 D-97896 Freudenberg/Main Tel: +49 (0) 93 75/84-0 Fax: +49 (0) 93

More information

User Guide for Viridian EV Charging Stations

User Guide for Viridian EV Charging Stations User Guide for Viridian EV Stations Iss 3 - JULY 2015 Page 2 of 8 Thank you for purchasing a Viridian EV station. This guide is intended to instruct in the proper use of all models of Viridian stations.

More information

INFO. SHEET: E1:1 INSPECTION & TESTING OF ELECTRICAL EQUIPMENT

INFO. SHEET: E1:1 INSPECTION & TESTING OF ELECTRICAL EQUIPMENT INFO. SHEET: E1:1 INSPECTION & TESTING OF ELECTRICAL EQUIPMENT This Information Sheet provides guidance on how to carry out User Checks, Formal Visual Inspections and combined Inspection and Tests on portable

More information

Instruction Manual MINI IRRIGATION CONTROLLER.

Instruction Manual MINI IRRIGATION CONTROLLER. MINI IRRIGATION CONTROLLER www.krain.com Station Models - Available in 4 OR 6 stations. OUTdoor MODEL - Supplied with 120VAC x 24VAC inbuilt transformer. Optional LEAD with Plug. Instruction Manual Table

More information

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY CAUTION: INSTALLATION LOCATION:

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY CAUTION: INSTALLATION LOCATION: 2 Please read the safety and installation instructions carefully to help ensure a correct and SAFE installation of your Second Wind Ultraviolet Germicidal Photo-catalytic Air Purifier. WARNING: FAILURE

More information

MODEL Nos: CVAC20SS CVAC25SS CVAC30SSR OPERATING & MAINTENANCE INSTRUCTIONS. Distributed by CLARKE International Ltd.

MODEL Nos: CVAC20SS CVAC25SS CVAC30SSR OPERATING & MAINTENANCE INSTRUCTIONS. Distributed by CLARKE International Ltd. MODEL Nos: CVAC20SS CVAC25SS CVAC30SSR OPERATING & MAINTENANCE INSTRUCTIONS Distributed by CLARKE International Ltd. 1006 Thank you for selecting this VAC KING Stainless Steel Vacuum Cleaner, which will

More information

BRAVER UPS. (Uninterruptible Power System) User s Manual

BRAVER UPS. (Uninterruptible Power System) User s Manual BRAVER UPS (Uninterruptible Power System) User s Manual Safety CAUTION! This UPS utilizes voltages that may be hazardous. Do not attempt to disassemble the unit. The unit contains no user replaceable parts.

More information

HEAVY DUTY BATTERY BOOSTERS / CHARGERS. MODEL Nos. BC185N & BC205N OPERATING INSTRUCTIONS

HEAVY DUTY BATTERY BOOSTERS / CHARGERS. MODEL Nos. BC185N & BC205N OPERATING INSTRUCTIONS HEAVY DUTY BATTERY BOOSTERS / CHARGERS MODEL Nos. BC185N & BC205N OPERATING INSTRUCTIONS 0614 Thank you for purchasing this CLARKE Battery Charger. These units are suitable for charging and boosting 12

More information

CFT24 &CFT230 PART NOS:

CFT24 &CFT230 PART NOS: FUEL TRANSFER PUMP Model Nos. CFT12, CFT24 &CFT230 PART NOS: 7160010, 7160020 & 7160030 INSTALLATION & OPERATING INSTRUCTIONS ORIGINAL INSTRUCTIONS GC05/18 REV 5 INTRODUCTION Thank you for purchasing this

More information

Doc Ref: WD030/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No

Doc Ref: WD030/2/11/12 Fern-Howard Ltd. 2 Newman Lane, Alton, Hampshire, GU34 2QR. Reg. No The Micro-Max is the smaller version of the Mini-Max, retaining the market leading features of the larger model. A prismatic diffuser gives an even light distribution from the energy efficient 2D lamp.

More information

MODEL SCA Installation and Operation Manual Important:

MODEL SCA Installation and Operation Manual Important: MODEL SCA Installation and Operation Manual Important: This manual contains specific cautionary statements relative to worker safety. Read this manual thoroughly and follow as directed. It is impossible

More information

SUBMERSIBLE WATER PUMP OPERATING & MAINTENANCE INSTRUCTIONS. Model Nos. CSE400A. Part No iss 2

SUBMERSIBLE WATER PUMP OPERATING & MAINTENANCE INSTRUCTIONS. Model Nos. CSE400A. Part No iss 2 SUBMERSIBLE WATER PUMP Model Nos. CSE400A Part No. 7231100 0917 iss 2 OPERATING & MAINTENANCE INSTRUCTIONS Thank you for purchasing this Clarke Submersible Pump. This highly efficient pump is designed

More information

12v / 24v Diesel Transfer Pump Kit

12v / 24v Diesel Transfer Pump Kit Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

PIL0478 ISSUE 01/ 07/16

PIL0478 ISSUE 01/ 07/16 ISSUE 01/ 07/16 PIL0478 ZAFIR G9 CEILING FITTING PIL0478 ISSUE 01/ 07/16 PART C PART E PART 21 SELV 1 1.B 1 3.1 3.3 3.4 3.5 3.6, 3.8 3.10 3.12 3.14 3.16 3.17 3.18 3.19 3.19 ATTENTION! THE TABLE BELOW

More information

User Manual Digital Water Level Indicator for rain water storage tanks

User Manual Digital Water Level Indicator for rain water storage tanks User Manual Digital Water Level Indicator for rain water storage tanks We congratulate you on the purchase of Digital Water Level measuring device. You have purchased a high-quality product built to the

More information

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS 100% recy-cling paper Bleached without chlorine GB Imprint These operating instructions are published by Conrad Electronic GmbH, Klaus- Conrad-Str 1, 92240 Hirschau/Germany No reproduction (including translation)

More information

EC MACHINE DIRECTIVE COMPLIANCE DECLARATION

EC MACHINE DIRECTIVE COMPLIANCE DECLARATION 770 EC MACHINE DIRECTIVE COMPLIANCE DECLARATION (DIRECTIVE 89/392 EEC, APPENDIX II, PART B) Manufacturer: FAAC S.p.A. Address: Via Benini, 1 40069 - Zola Predosa BOLOGNA - ITALY Hereby declares that: the

More information

Operating Instructions

Operating Instructions Operating Instructions Pendant Light Fitting > Contents 1 Contents 1 Contents...2 2 General Information...2 3 General Notes Regarding Safety...3 4 Intended Area of Application...4 5 Technical Data...5

More information

Dedicated PIR Light Controller c/w RF remote control for LEDPRO Floodlights

Dedicated PIR Light Controller c/w RF remote control for LEDPRO Floodlights Dedicated PIR Light Controller c/w RF remote control for LEDPRO Floodlights Model: LEDPRORFKB Black Model: LEDPRORFKWH White Model: LEDPROFOB RF Remote Fob Installation & Operating Instructions 1 1. General

More information

BENCH GRINDER MODEL CBG6RP OPERATING & MAINTENANCE INSTRUCTIONS 0101

BENCH GRINDER MODEL CBG6RP OPERATING & MAINTENANCE INSTRUCTIONS 0101 BENCH GRINDER MODEL CBG6RP OPERATING & MAINTENANCE INSTRUCTIONS 0101 Thank you for purchasing this CLARKE Bench Grinder Before attempting to operate this machine, please read this instruction manual thoroughly

More information

7.5 Oregon Fir With SYLVANIA Multi Color Mini Lights and Multi Color G50 Soft Glow Lights Pre-Lighted Tree V69139 INSTRUCTION MANUAL

7.5 Oregon Fir With SYLVANIA Multi Color Mini Lights and Multi Color G50 Soft Glow Lights Pre-Lighted Tree V69139 INSTRUCTION MANUAL 7.5 Oregon Fir With SYLVANIA Multi Color Mini Lights and Multi Color G50 Soft Glow Lights Pre-Lighted Tree V69139 INSTRUCTION MANUAL Thank you for purchasing a SYLVANIA pre-lighted tree. This tree assembles

More information

World Leaders in Diesel Fuel Injection Test Equipment. IFT-c. Injector Function Tester Controller. Operating and Servicing Manual

World Leaders in Diesel Fuel Injection Test Equipment. IFT-c. Injector Function Tester Controller. Operating and Servicing Manual World Leaders in Diesel Fuel Injection Test Equipment. IFT-c Injector Function Tester Controller Operating and Servicing Manual HL048 (EN) Issue 4, H1852, August 2011 HARTRIDGE LIMITED IFT-c Operating

More information

PROFESSIONAL CORDLESS IMPACT SCREWDRIVER

PROFESSIONAL CORDLESS IMPACT SCREWDRIVER PROFESSIONAL CORDLESS IMPACT SCREWDRIVER Model CIS00 Part No 4500625 OPERATING & MAINTENANCE INSTRUCTIONS GC0309 INTRODUCTION Thank you for purchasing this CLARKE Impact Screwdriver. Before attempting

More information

Pro Series 2120 COMMERCIAL ROLLER SHUTTER OPENER

Pro Series 2120 COMMERCIAL ROLLER SHUTTER OPENER AUTOMATIC TECHNOLOGY AUSTRALIA PTY LTD Pro Series 2120 COMMERCIAL ROLLER SHUTTER OPENER OWNERS COPY Installation Instructions WARNING It is vital for the safety of persons to follow all instructions. Failure

More information

ELECTRO-MECH SCOREBOARD CO.

ELECTRO-MECH SCOREBOARD CO. ELECTRO-MECH SCOREBOARD CO. MM-338 FOOTBALL SCOREBOARD OWNER S HANDBOOK Thank you for choosing an Electro-Mech Scoreboard for your athletic complex. We are confident that your new scoreboard will give

More information

Installation and Set Up Instructions

Installation and Set Up Instructions SL 2000 DC2 SLIDING GATE MOTOR KIT Solar Powered and 12V Low Voltage Installation and Set Up Instructions Unit 27 / 49 Corporate Boulevard Bayswater Vic 3153 Phone 1800 111 930 Email info@gforceautogates.com.au

More information

SUBMERSIBLE PUMP. Model No: HIPPO 2 OPERATING & MAINTENANCE INSTRUCTIONS

SUBMERSIBLE PUMP. Model No: HIPPO 2 OPERATING & MAINTENANCE INSTRUCTIONS SUBMERSIBLE PUMP Model No: HIPPO 2 OPERATING & MAINTENANCE INSTRUCTIONS 0107 1 HIPPO 2 240 Volt and 110 Volt models Thank you for purchasing this Clarke Hippo 2 Pump. Before attempting to operate this

More information

Power Inverter 400 MW Owner s Manual

Power Inverter 400 MW Owner s Manual Power Inverter 400 MW 1204 Owner s Manual For safe and optimum performance, the Power Inverter must be used properly. Carefully read and follow all instructions and guidelines in this manual and give special

More information

SDM320D / SDM320A. Single phase din rail meter SDM320D / SDM320A user manual

SDM320D / SDM320A. Single phase din rail meter SDM320D / SDM320A user manual SDM320D / SDM320A DIN Rail Single Phase Two Wire Energy Meter with S0 Pulse Output (Four modular) User Manual ------------------- 1.1 Safety instruction 1.2 Introductions 1.3 Performance criteria 1.4 Specifications

More information

230V DIESEL FUEL TRANSFER PUMP MODEL NO: DFT230

230V DIESEL FUEL TRANSFER PUMP MODEL NO: DFT230 230V DIESEL FUEL TRANSFER PUMP MODEL NO: DFT230 PART NO: 7160050 OPERATION & MAINTENANCE INSTRUCTIONS GC0816 INTRODUCTION Thank you for purchasing this CLARKE Pump. The DFTP230 pump is a self-priming rotary

More information

Installation Example and Guide

Installation Example and Guide Installation Example and Guide Author: Road Angel Group Date: May 2016 Version: 1.00 Version 1.00 Page 1 of 12 Contents CONTENTS... 2 INTRODUCTION... 3 SCOPE... 3 ITEMS REQUIRED FOR HARDWIRE INSTALLATION...

More information

BATTERY CHARGER-STARTER

BATTERY CHARGER-STARTER BATTERY CHARGER-STARTER MODEL NO: WBC240 & WBC400 PART NO: 6261505 & 6261515 OPERATION & MAINTENANCE INSTRUCTIONS GC0116 INTRODUCTION Thank you for purchasing this CLARKE Battery Charger/Starter. Please

More information

27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2

27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2 1 27.6 Vdc 1 Amp Switch Mode Power Supply for Fire EN54-4:1997 +A1 +A2 STX2401-C STX2401-T FEATURES 0843-CPR-0213 14 Elmdene International Ltd Tel: +44(0)23 9269 6638 3 Keel Close, Interchange Park, Fax:

More information