YS11 SMALL THERMAL MOTOR PROTECTOR / THERMAL CUT-OUT

Transcription

1 YS11 SMLL THERML MOTOR PROTECTOR / THERML CUT-OUT Features YS11 was developed to protect people and property from accidents or failures that can occur in motors used in fans and washing machines as well as other appliances. It functions as a self-resetting thermal cut-out (Type 2), thermal motor protector (Type 3C) and thermal protector for ballasts. The YS11 can be used for on-winding and outside of resin packed motors by clamping or insertion. Since the YS11 has a plastic case, it does not need to be insulated from metal part of the motor. SPECIFICTIONS Technical Characteristics Contact Capacity Temperature Range Tolerance on Open Temp. TCO, TMP TCO allast 7/2Vac, /125Vac 6/24Vdc, 15/18Vdc 2/2Vac Motor Protector and Temp. Control to 1 C allast protection to 1 C ± 5K Max. Temp. of the Switch Head 1 C Operating Time Pollution Situation Extent of Sensing Element Degree of Protection Electrical Connections Continuous Dirty Whole Control IP00 Soldering, Welding Page 1

2 Construction YS11 is constructed with simple design and based on the well known thermostat technology of Sensata Technologies, and it has enough sealing capability to withstand varnish process and can be laced on winding. 7.Movable rm carries current from 1.Lead to 9.Lower Terminal which is insert molded in 6.Lower lock, via.movable Contact and Stationary Contact. 7.Movable rm, 8.imetal Disc and 5.Upper Plate are riveted to secure with 6.Lower lock by 4.Eyelet. This assembly is inserted into 3.Case, and potting Epoxy to seal. Since trip time to cut off the power depends on the operation temperature of YS11 protector, each rating should be selected properly. Referencing the performance curve, a YS11 can be selected to match a motor. pplication Notes R-type case was developed for Resin Packed Motor and was designed to resist high pressure which may be applied during molding process. Maximum pressure is required to be control within 7.5Mpa. Please note that R-type case does not have enough sealing capability, therefore it should not be applied for winding varnish process. Dimension is 6.0mm x 7.8mm (ellipse) x 23.0mm length. Used with the S-Type Case in higher ambient temperature and same configuration as standard case. Housing material is used PPS (RTI:2 C) which is same as R-type case, so that it can resist high temperature for short time. This case is not guaranteed for varnish process as well. Rating should be selected properly to protect Motors and other equipment. Short time trip current and time is described in Performance page which helps to choose most adequate operating temperature. Must hold current is also one of important performances, it can be selected from UTC performance curve as well. Curves (Performance) Short time trip performance and Ultimate trip current as reference. Short Time Trip YS 11 (C1) Current() 20 Trip Time(sec) 1 0 Page 2

3 DIMENSIONS Standard Type Case : Width 6.9 x Length 21.5 x Height 4.0mm excluding leads. No. Part Description Material 1 Leads Refer Ordering Options 2 Epoxy 3 Case PT or PPS 4 Eyelet rass 5 Upper Plate rass 6 Lower lock PT 7 Movable rm Refer Ordering Options 8 imetal Disc 9 Lower Terminal rass Stationary Contact gni alloy Page 3

4 ORDERING OPTIONS Device Identification Example : YS111-C7 YS11 with C1 material Movable rm. 1 C open, C Close temperature. UL 3398 WG22 mm length leads YS11 X YYYT ZW(ZZZ) (V) Performance Identification Code Open and Close Temp. Code Optional Leads, Material, Length, Etc. Other Options ecu C1 ecu C1 rm Material See Chart. / YYY = Open Temp. Code / T = Close Temp. Code See Chart. Omit: No Option R: Reinforced Case S: PPS Case T: Groove Contact (For DC Rating Only) U: Groove Contact and CD C19220 for lower terminal (For DC Rating Only) Chart. Code *2 *2 *2 *2 * YYY Open ( C) *1 = Close Temp. For Reference *2 = is for Snap Open/Close guaranteed. is for Snap Open guaranteed T Close ( C) *1 Chart. Z = Leads material can be selected from table below as standard rating: C D E F G UL style 3266 WG22 Tin coated-l UL style 14 WG22-WH UL style 3398 WG22 Tin coated-yl(kurabe) UL style 3398 WG22-YL(Kurabe) UL style 3266 WG22-K Copper Solid Wire D=0.8mm UL style 3266 WG22 Tin coated-wh W = Leads length can be selected from Table below as standard rating. 5mm Length mm Strip W Length W Length (ZZZ) = Other than above standard combination, 2 or 3 digits of number or letter is assigned as customized one. Page 4

5 GENCY PPROVLS & CERTIFICTIONS Series UL ENEC CQC E15962 for Motor Protector E34618 for Temp Indicating & Regulating for thermal cut-out, motor and ballast protector CQC /CQC Protectors are not applied in CCC(China Compulsory Certification) at present. So YS11 can not have CCC but CQC. CQC (China Quality Certification Centre) is a national certification body for appliance in China. Page 5 Sensata Technologies, Inc. ( Sensata ) data sheets are solely intended to assist designers ( uyers ) who are developing systems that incorporate Sensata products (also referred to herein as components ). uyer understands and agrees that uyer remains responsible for using its independent analysis, evaluation and judgment in designing uyer s systems and products. Sensata data sheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, improvements and other changes to its data sheets or components without notice. uyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, Y ESTOPPEL OR OTHERWISE TO NY OTHER SENST INTELLECTUL PROPERTY RIGHT, ND NO LICENSE TO NY THIRD PRTY TECHNOLOGY OR INTELLECTUL PROPERTY RIGHT, IS GRNTED HEREIN. SENST DT SHEETS RE PROVIDED S IS. SENST MKES NO WRRNTIES OR REPRESENTTIONS WITH REGRD TO THE DT SHEETS OR USE OF THE DT SHEETS, EXPRESS, IMPLIED OR STTUTORY, INCLUDING CCURCY OR COMPLETENESS. SENST DISCLIMS NY WRRNTY OF TITLE ND NY IMPLIED WRRNTIES OF MERCHNTILITY, FITNESS FOR PRTICULR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, ND NON-INFRINGEMENT OF NY THIRD PRTY INTELLECTUL PROPERTY RIGHTS WITH REGRD TO SENST DT SHEETS OR USE THEREOF. ll products are sold subject to Sensata s terms and conditions of sale supplied at SENST SSUMES NO LIILITY FOR PPLICTIONS SSISTNCE OR THE DESIGN OF UYERS PRODUCTS. UYER CKNOWLEDGES ND GREES THT IT IS SOLELY RESPONSILE FOR COMPLINCE WITH LL LEGL, REGULTORY ND SFETY-RELTED REQUIREMENTS CONCERNING ITS PRODUCTS, ND NY USE OF SENST COMPONENTS IN ITS PPLICTIONS, NOTWITHSTNDING NY PPLICTIONS-RELTED INFORMTION OR SUPPORT THT MY E PROVIDED Y SENST. Mailing ddress: Sensata Technologies, Inc., 529 Pleasant Street, ttleboro, M 023, US. Copyright 2018 Sensata Technologies, Inc. Rev:05/01/18 CONTCT US mericas +1 (8) electrical-protection-sales@sensata. com Europe, Middle East & frica +1 (7) motors-info.eu@sensata.com sia Pacific EP_sia_Public@list.sensata.com China +86 (21)26 11 Japan +81 () Korea +82 (53) India +91 () Rest of sia +886 (2) ext 28