ALTERNATOR/STARTER CLUTCH/ CAM CHAIN TENSIONER
|
|
- Garey Wells
- 5 years ago
- Views:
Transcription
1 8 ALTERNATOR/STARTER CLUTCH/ SERVICE INFORMATION TROUBLESHOOTING ALTERNATOR REMOVAL STARTER CLUTCH REMOVAL CAM CHAIN TRNSIONER TENSIONER SPRING AND PUSH ROD STARTER CLUTCH INSTALLATION
2 8. ALTERNATOR/STATER CLUTCH/ SCHEMATIC DRAWING 8-1
3 SERVICE INFORMATION GENERAL INSTRUCTIONS The starter motor, generator, left crankcase and starter clutch can be serviced in the frame. Do not install the starter clutch forcedly. Install the generator by aligning the groove in the flywheel with the key on the crankshaft. Install the starter motor reduction gear shaft by aligning the shaft pin with the shaft seat groove. SPECIFICATIONS Item Standard (mm) Service Limit (mm) Push rod O.D ~ Driven sprocket O.D ~ Driven sprocket I.D ~ Tensioner spring free length 110~ TORQUE VALUES Flywheel lock nut SPECIAL TOOLS Flywheel holder Flywheel puller 3.2~4.0kg-m E021 E003 TROUBLESHOOTING Hard starting and poor performance at high speed Improperly tightened flywheel lock bolt Starter clutch slips Worn starter clutch roller Faulty starter clutch roller or spring Worn starter gear shaft O.D. Starting noise Worn reduction gear Worn starter gear Worn starter clutch roller Faulty reduction gear shaft bearing 8-2
4 8. ALTERNATOR/STATER CLUTCH/ ALTERNATOR REMOVAL Remove the four bolts. Remove the left crankcase cover. Bolts Remove the gasket and dowel pins. Gasket Dowel Pins Remove the flywheel nut and washer while holding the flywheel with a flywheel holder. Flywheel Holder Special Flywheel holder Remove the flywheel using a flywheel puller as shown. Flywheel Puller Special Flywheel puller 8-3
5 Remove the clamp. Remove the five bolts and alternator stator base from the crankcase cover. Do not disassemble the stator and pulse generator coils. Clamp Bolts STARTER CLUTCH REMOVAL REMOVAL Drain the engine oil (page 3-3) Remove the alternator (page 8-3) Remove the stopper plate and chain sliders. Remove the snap ring. Remove the chain, starter drive sprocket and driven sprocket as an assembly. Stator Base Snap Ring Drive Sprocket Stopper Plate Chain Sliders Driven Sprocket Remove the two screws, base plate and three O-rings. INSPECTION Inspect the chain sliders for wear or damage. Replace them if necessary. Screws Chain Sliders Base Plate 8-4
6 8. ALTERNATOR/STATER CLUTCH/ INSPECTION Measure the driven sprocket O.D. Service Limit:37.83mm replace if over Measure the driven sprocket I.D. Service Limit:19.06mm replace if over Check the one-way clutch rollers, spring caps and springs for wear or damage. Spring Spring Cap Roller REMOVAL Drain the engine oil (page 3-3) Remove the alternator (page 8-3) Remove the starter clutch (page 8-4) Remove the tensioner sealing bolt, washer, spring and tensioner rod. Remove the pivot bolt and cam chain tensioner. Cam Chain Tensioner Tensioner Rod Spring Washer And Bolt TENSIONER SPRING AND PUSH ROD INSPECTION Measure the tensioner spring free length. Service limit: 90mm 8-5
7 Check the push rod valve for clogged Check the push rod for wear or scraches. Measure the push rod O.D. Service limit: mm One Way Valve INSTALLATION Install the cam chain tensioner and secure it with the pivot bolt. Install the tensioner rod, spring, sealing washer bolt. Tighten the tensioner sealing bolt. TORUQE: 1.5~2.5 kg-m Install the tensioner spring with its small coil end up. Install the starter clutch and alternator (page 8-6) Tensioner Spring Tensioner Rod Sealing Washer And Bolt STARTER CLUTCH INSTALLATION Install the new O-rings onto the left crankcase and base plate, Install the base plate, being careful not to damage the O-ring. Tighten the base plate screws. Base Plate O-rings 8-6
8 8. ALTERNATOR/STATER CLUTCH/ Install the chain, drive sprocket and driven sprocket as an assembly. Install the following components: -snap ring. -stopper plate. -chain sliders. Snap Ring Chain Stopper Plate Chain Sliders Grommet Clamp Bolts Install the alternator stator base and secure it with the two bolts. Install the grommet into the grove of the left crankcase cover. Install the wire clamp. Install the woodruff key on the crankshaft, Wipe all oil lff the inside of the flywheel amd crankshaft, and install the flywheel aligning its groove with the woodruff key. Install the flywheel, turning it counterclockwise. Install and tighten the flywheel nut while holding the flywheel with a flywheel holder. TORQUE: 3.2~4.0 kg-m Special Flywheel Holder Flywheel Holder Stator Base Nut 8-7 Drive Sprocket
9 Install the dowel pins and a new gasket. Gasket Dowel Pins Install the left crankcase cover and tighten the four bolts. Torque: 0.8~1.2kg-m Bols 8-8
11. ALTERNATOR/STARTER CLUTCH
11. ALTERNATOR/STARTER CLUTCH COMPONENT LOCATION 11-2 SERVICE INFORMATION 11-3 TROUBLESHOOTING 11-3 STATOR REMOVAL 11-4 FLYWHEEL/STARTER CLUTCH 11-6 STATOR INSTALLATION 11-12 11 11-1 ALTERNATOR/STARTER
More informationE03 CYLINDER HEAD ASSY 1 BN0030 Dowel Pin 4
E01 FAN COVER ASSY 1 BN0061-1 Clip 1 2 150ZT-E01.02 BN0064 Fan Cover 1 3 BN0061-2 Bracket 1 4 150ZT-E01.04 BN0064-4 Carburetor Cooling Duct 1 5 150ZT-E01.05 BN0064-3 Decorative Cover 1 6 150ZT-E01.06 BN0063-2
More informationE02 CYLINDER HEAD COVER ASSY
TNG 150cc ZT E01 FAN COVER ASSY 1 BN0061-1 Clip 1 2 150ZT-E01.02 BN0064 Fan Cover 1 3 BN0061-2 Bracket 1 4 150ZT-E01.04 BN0064-4 Carburetor Cooling Duct 1 5 150ZT-E01.05 BN0064-3 Decorative Cover 1 6 150ZT-E01.06
More information4. LUBRICATION SYSTEM
4 LUBRICATION SYSTEM Rocker Arm Shaft Crankshaft Oil Filter Screen Oil Pump 4-0 SERVICE INFORMATION... 4-1 ENGINE OIL/OIL FILTER...4-2 TROUBLESHOOTING... 4-1 OIL PUMP...4-3 SERVICE INFORMATION GENERAL
More information4. LUBRICATION SYSTEM
4 4 LUBRICATION SYSTEM SERVICE INFORMATION------------------------------------------------ 4-1 TROUBLESHOOTING----------------------------------------------------- 4-1 ENGINE OIL/OIL FILTER ------------------------------------------------
More informationTROUBLESHOOTING. Avoid getting grease and oil on the drive belt and pulley faces.
8 KICK STARTER/DRIVE PULLEY/ SERVICE INFORMATION... 8-2 TROUBLESHOOTING... 8-2 LEFT CRANKCASE COVER... 8-3 DRIVE PULLEY... 8-3... 8-7 KICK STARTER... 8-14 0 1 SERVICE INFORMATION GENERAL INSTRUCTIONS Avoid
More information10. CRANKCASE/CRANKSHAFT/TRANS- MISSION SYSTEM/STARTER SPINDLE CK
10 10 10-0 SERVICE INFORMATION... 10-1 STARTER SPINDLE... 10-6 TROUBLESHOOTING... 10-2 CRANKSHAFT... 10-8 CRANKCASE REMOVAL... 10-3 CRANKCASE INSTALLATION... 10-10 TRANSMISSION SYSTEM... 10-3 SERVICE INFORMATION
More information8 TROUBLESHOOTING
8 DRIVE AND DRIVEN PULLEYS/ SCHEMATIC DRAWING------------------------------------------------------------------------- 8-1 SERVICE INFORMATION-----------------------------------------------------------------------
More information8. DRIVE AND DRIVEN PULLEYS/
8 DRIVE AND DRIVEN PULLEYS/ SCHEMATIC DRAWING ---------------------------------------------- 8-1 SERVICE INFORMATION -------------------------------------------- 8-2 TROUBLESHOOTING -------------------------------------------------
More information10. ALTERNATOR/STARTER CLUTCH
10. ALTERNATOR/STARTER CLUTCH SYSTEM COMPONENTS 10-2 SERVICE INFORMATION 10-3 TROUBLESHOOTING 10-3 LEFT CRANKCASE COVER REMOVAL 10-4 STATOR/IGNITION PULSE GENERATOR 10-5 FLYWHEEL/STARTER CLUTCH 10-6 LEFT
More informationKICK STARTER/DRIVE PULLEY/ CLUTCH/DRIVEN PULLEY SERVICE INFORMATION TROUBLESHOOTING KICK STARTER DRIVE BELT...
8 KICK STARTER/DRIVE PULLEY/ 8 SERVICE INFORMATION... 8-2 TROUBLESHOOTING... 8-2 KICK STARTER... 8-3 DRIVE BELT... 8-7 DRIVE PULLEY... 8-9 STARTER ONE-WAY CLUTCH DRIVE GEAR... 8-11... 8-14 8-0 Torque:
More informationSPARE PARTS ENGINE S6/E
SPARE PARTS ENGINE ENGINE BLOCK CODE DENOMINATION QTY NOTE TABLE -0690 COMPLETE CRANKCASE A 0-6067 BEARING 7-35-0 A 0 0-5070 SNAP RING FOR HOLE DIAMTER 36 A 03 0-85 ROLLER CAGE HK 7 B A 04 0-6033 OIL SEAL
More informationCUV CARRY 400 Parti di ricambio - Motore
27 EXHAUST REF. No. PART NO. DESCRIPTION Q'TY 1 27107 MUFFLER 1 2 25222 JOUNT 2 3 27108 EXHAUST PIPE 1 4 23403 EXHAUST PIPE GASKET 1 5 10106 WASHER 8 2 6 10099 NUT M8 2 7 23408 SPRING 5 8 27109 ACCELERANT
More information4. LUBRICATION SYSTEM
4 4 LUBRICATION SYSTEM LUBRICATION SYSTEM DIAGRAM --------------------------------- 4-1 SERVICE INFORMATION----------------------------------------------- 4-2 TROUBLESHOOTING----------------------------------------------------
More informationCVT Continuously Variable Transmission
4. CVT Continuously Variable Transmission XCITING 400i CVT Continuously Variable Transmission This chapter covers the location and servicing of the CVT components for the KYMCO XCITING 400i. Belt Case...
More informationGenerator/Starter Clutch
8-0 8. Generator/Starter Clutch Service Information 8-1 Shroud 8-2 A.C Generator 8-2 R.Crank Case Cover 8-4 Starter Clutch 8-6 Service Information General Safety This section describes the removal and
More information9. DRIVE AND DRIVEN PULLEYS/ KICK STARTER AGILITY CITY ~6.0kg-m g-m g-m 9-0
9 5.0~6.0kg-m 3.5-4.5g-m 9 3.5-4.0g-m 9-0 SERVICE INFORMATION...9-1 DRIVE BELT...9-5 TROUBLESHOOTING...9-1 DRIVE PULLEY...9-6 LEFT CRANKCASE COVER...9-2 CLUTCH/DRIVEN PULLEY...9-9...9-2 SERVICE INFORMATION
More information9. DRIVE AND DRIVEN PULLEYS/ KICK STARTER AGILITY ~6.0kg-m g-m g-m 9-0
9 5.0~6.0kg-m 3.5-4.5g-m 9 3.5-4.0g-m 9-0 SERVICE INFORMATION...9-1 DRIVE BELT...9-5 TROUBLESHOOTING...9-1 DRIVE PULLEY...9-6 LEFT CRANKCASE COVER...9-2 CLUTCH/DRIVEN PULLEY...9-9...9-2 SERVICE INFORMATION
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 680GC Petrol Concrete Saw Serial numbers starting with 967 & 977 Effective January 1, 2011 TABLE OF CONTENTS 680GC Petrol Concrete Saw ITEM DESCRIPTION KEY PAGE
More informationDIAMO TURISTA 300CC ENGINE PARTS CATALOG. Second Edition March 2008
DIAMO TURISTA 300CC ENGINE PARTS CATALOG Second Edition March 2008 Copyright 2004-2008 LS MotorSports, LLC. Reproduction without written permission is completely forbidden. The information and diagrams
More information7. CYLINDER HEAD/VALVES
7 7 7-0 SERVICE INFORMATION...7-1 CYLINDER HEAD DISASSEMBLY...7-7 TROUBLESHOOTING...7-2 CYLINDER HEAD ASSEMBLY...7-8 CAMSHAFT REMOVAL...7-3 CYLINDER HEAD INSTALLATION...7-8 CYLINDER HEAD REMOVAL...7-5
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 613GC Gas Concrete Saw Effective January 1, 2010 SERVICE ITEMS 613GC Gas Concrete Saw Above 71700 Gas Saw Service Tool Kit, includes all items shown above $668.00
More informationE1 Cylinder Head Cover
E1 Cylinder Head Cover 1 E0101-001-70E Cover, upper cylinder head 1 2 E0101-002-70E Cover, R. cylinder head 1 3 E0101-003-70E cover, L.cylinder head 1 4 E0101-004-70E Cap, valve chamber 2 5 E0101-005-70E
More informationDVX 90 MODEL NUMBER A2008KSB2BUSD (BLACK-RED) MODEL NUMBER A2008KSB2BUSE (BLACK-CAT GREEN) MORE TO GO ON. TM
2008 DVX 90 Illustrated Parts Manual MODEL NUMBER A2008KSB2BUSD (BLACK-RED) MODEL NUMBER A2008KSB2BUSE (BLACK-CAT GREEN) MORE TO GO ON. TM TABLE OF CONTENTS Black-Red (Model No. A2008KSB2BUSD) Black-Cat
More information9-8 LEFT CRANKCASE COVER INSTALLATION ALTERNATORETARTER A TORIST ARTER CLUTCH. Install the dowel pin and a new gasket.
ALTERNATORETARTER A TORIST ARTER CLUTCH LEFT CRANKCASE COVER INSTALLATION Install the dowel pin and a new gasket. Install the left crankcase cover. Install the washer and bolts, and tighten them securely.
More informationIllustration Engine. PTX 2710 (EPA 3) Pole pruner. 3/27/2017 Page Copyright COMET USA, INC.
Documents Engine Starter assy and clutch Tank and air filter Adjustable telescopic pole Pruner Carburetor WT-1150 Accessories 3/27/2017 Page 1-16 Illustration Engine 3/27/2017 Page 2-16 Illustration Engine
More informationATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 1 of 58 AIR INTAKE ASSEMBLY
2008 ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 1 of 58 AIR INTAKE ASSEMBLY 2008 ATV 90 UTILITY CALIFORNIA GREEN (A2008KUB2BCAG) Page 2 of 58 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description
More informationPDFMAILER.COM Print and send PDF files as s with any application, ad-sponsored and free of charge
19.0 CYLINDER 1 82848 CYLINDER HEAD ASSY (ATV 260) 1 1a 83154 CYLINDER HEAD ASSY( ATV300) 1 2 82021 GUIDE INTAKE VALVE 2 3 82022 CIRCLIP 12 2 4 82023 BOLT M6X12 1 5 82024 GASKET 6 1 6 82025 BOLT STUD M8X25
More informationATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY
2008 ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 1 of 60 AIR INTAKE ASSEMBLY 2008 ATV 50 DVX BLACK-RED (A2008KSA2BUSD) Page 2 of 60 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-005
More information9-0 CYLINDER/PISTON 9. CYLINDER/PISTON. MXU 500i DX
9 CYLINDER/PISTON SCHEMATIC DRAWING ------------------------------------------------- 9-1 SERVICE INFORMATION------------------------------------------------ 9-2 TROUBLESHOOTING-----------------------------------------------------
More information613GC Key A Parts Starter & Ignition Assembly
613GC Key A Parts Starter & Ignition Assembly 73866 Screw (same as B26) A01 505514 Starter Rope Handle A02 73904 Starter Rope A03 73909 Starter Coil Spring & Housing A04 71451 Starter Case Plate A05 73910
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 613GC Gas Concrete Saw Effective January 1, 2011 TABLE OF CONTENTS 613GC Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 613GC Gas Saw Service Items n/a ii Starter
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 680GC Gas Concrete Saw Serial numbers starting with 967 & 977 Effective July 1, 2015 I TABLE OF CONTENTS 680GC Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC
More information~ :H:OlVD.A. CB1000C CLUTCH Date of Issue: Sept., 1982 HONDA MOTOR CO., LTD.
~ :H:OlVD.A. CB1000C 8-0 118 ~ :H:OlVD.A. CB1000C 8. SERVICE INFORMATION TROUBLESHOOTING COVER REMOVAL REMOVAL 8-1 8-2 8-3 8-3 INSTAllATION COVER INSTAllATION STARTER DISASSEMBLY STARTER ASSEMBLY 8-6 8-9
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 680GC Petrol Concrete Saw Serial numbers starting with 967 & 977 Effective January 1, 2013 I TABLE OF CONTENTS 680GC Petrol Concrete Saw ITEM DESCRIPTION KEY
More informationModel NSR125R1 - CYLINDER/CYLINDER HEAD
Model NSR125R1 - CYLINDER/CYLINDER HEAD 1 12110KY4900 CYLINDER COMP. A 001 79.220 1 12120KY4900 CYLINDER COMP. B 001 79.220 1 12130KY4900 CYLINDER COMP. C 001 79.220 1 12140KY4900 CYLINDER COMP. D 001
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 680GC Gas Concrete Saw Serial numbers starting with 967 & 977 Effective January 1, 2019 I TABLE OF CONTENTS 680GC Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC
More information4. LUBRICATION SYSTEM
4 4 LUBRICATION SYSTEM LUBRICATION SYSTEM DIAGRAM ---------------------------------- 4-1 SERVICE INFORMATION------------------------------------------------ 4-2 TROUBLESHOOTING-----------------------------------------------------
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 680ES Gas Concrete Saw Effective July, 0 I TABLE OF CONTENTS 680ES Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC Gas Saw Service Items n/a Starter Assembly
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 633GC / 633F4 Gas Concrete Saws Effective January 1, 20167 TABLE OF CONTENTS 633GC / 633F4 Gas Saws ITEM DESCRIPTION KEY PAGE 633GC / 633F4 Gas Saw Service Items
More informationCHAIN SAW PARTS CATALOG MODEL CS-6700 TYPE 1E SERIAL NUMBER & UP
CHAIN SAW PARTS CATALOG MODEL CS-00 TYPE 1E SERIAL NUMBER 0001 & UP ECHO, INCORPORATED 400 OAKWOOD ROAD LAKE ZURICH, IL 004 999203008 0/03 CS-00 TYPE 1E ENGINE, CRANKCASE, CYLINDER, PISTON 20 1 2 38 39
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 680ES Gas Concrete Saw Effective July 1, 2015 I TABLE OF CONTENTS 680ES Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC Gas Saw Service Items n/a 1 Starter Assembly
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 680ES Gas Concrete Saw Effective January 1, 2017 I TABLE OF CONTENTS 680ES Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC Gas Saw Service Items n/a 1 Starter
More informationATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY
2006 ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 1 of 60 AIR INTAKE ASSEMBLY 2006 ATV 90 UTILITY GREEN (A2006KUB2BUSG) Page 2 of 60 AIR INTAKE ASSEMBLY Ref # Part Number Qty S/P/F Description 1 3303-005
More information1/24/2008 HANDLE BAR ASSEMBLY MODEL MB165, HT65. Item No.
165 Toll Free: 888-863-2252 (BAJA) PARTS AND PRICES ARE SUBJECT TO CHANGE 1 of 28 HANDLE BAR ASSEMBLY Part UPC Number Description Baja Description 1 165-001 883099010613 GRIP, RIGHT, THROTTLE CONTROL 1
More informationF1 CRANKCASE ASSY. NOTES: V5 Engine Model:172MM D# PART# DESCRIPTION Q'TY 1 172MM-A RIGHT CRANKCASE COMP. 1
NOTES: V5 Engine Model:172MM F1 CRANKCASE ASSY. 1 172MM-A-011200 RIGHT CRANKCASE COMP. 1 2 152MI-011010 OUTER BUSH, ENGINE SUSPENSION 2 3 152MI-011008 O-RING, 15.8 2.4 4 4 152MI-011009 INNER BUSH, ENGINE
More information23. ELECTRIC STARTER (TRX450ER)
23. ELECTRIC STARTER (TRX450ER) COMPONENT LOCATION 23-2 STARTER MOTOR 23-6 SYSTEM DIAGRAM 23-2 STARTER RELAY SWITCH 23-13 SERVICE INFORMATION 23-3 CLUTCH DIODE 23-14 TROUBLESHOOTING 23-4 23-1 COMPONENT
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 680GC Gas Concrete Saw Serial numbers starting with 967 & 977 Effective January 1, 2018 I TABLE OF CONTENTS 680GC Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC
More informationCHAIN SAWS G561AVS G621AVS
2626-93121 CHAIN SAWS G561AVS G621AVS APPLICABLE SERIAL NUMBERS: OCTOBER 1998 G561AVS 814608 and up G621AVS 820954 and up Fig.1 1 Fig.2 2 Fig.1 1 1 2616-12112 2618-12115 CYLINDER 1 K4 2 3356-12141 GROMMET
More informationK&T Saw Shop or
14-600080 MINI MAC 6A 05/73 to 12/73 IPL 89090 Page 1 of 12 Accessories www.ktoutdoor.com 14-600080 MINI MAC 6A 05/73 to 12/73 IPL 89090 Page 2 of 12 Accessories 84992 Kit - Reed muffler 85933 Kit - Spark
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 613GC Gas Concrete Saw Effective January 1, 2017 TABLE OF CONTENTS 613GC Gas Concrete Saw ITEM DESCRIPTION KEY PAGE 613GC Gas Saw Service Items n/a 1 Starter
More informationReplacement Parts & Accessories Price List. 633GC Gas Saw
Replacement Parts & Accessories Price List 633GC Gas Saw Effective January 1, 2006 2006 ICS, Blount Inc. 4909 SE International Way Portland, OR 97222 TABLE OF CONTENTS 633GC Gas Saw ITEM DESCRIPTION KEY
More informationOVERHAULING THE ENGINE. 85 Nm (8.5 m kg, 61 ft Ib) Order Job/Part Q ty Remarks Removing the drive sprocket
INE EAS00188 INE DRIVE SPROCKET OVERHAULING THE INE 10 Nm (1.0 m kg, 7.2 ft Ib) 85 Nm (8.5 m kg, 61 ft Ib) Order Job/Part Q ty Remarks Removing the drive sprocket Remove the parts in the order listed.
More informationSpecial Crankcase set for Complete engine (4SMS)
Special Crankcase set for Complete engine (4SMS) (Takegawa original stud pattern) (For 123cc only) (For 138cc only) (For SCUT 148cc only) Thank you for purchasing one of our products. This crankcase set
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 680ES Petrol Concrete Saw Effective January, 08 I TABLE OF CONTENTS 680ES Petrol Concrete Saw ITEM DESCRIPTION KEY PAGE 680GC Petrol Saw Service Items n/a Starter
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 613GC Petrol Concrete Saw Effective January 1, 2013 TABLE OF CONTENTS 613GC Petrol Concrete Saw ITEM DESCRIPTION KEY PAGE 613GC Petrol Saw Service Items n/a
More informationK&T Saw Shop or
11-600036D PRO MAC 60 07/72 to 12/76 IPL 89321 Page 1 of 19 Accessories www.ktoutdoor.com 11-600036D PRO MAC 60 07/72 to 12/76 IPL 89321 Page 2 of 19 Accessories 84453 Kit - Piston tool 69191 Kit - Pressure
More informationDRAGON FLY 400 Parti di ricambio - agg
19 CYLINDER REF. No. PART NO. DESCRIPTION Q'TY 1 27337 CYLINDER HEAD ASSY 1 2 27338 GUIDE INTAKE VALVE 2 3 10112 CIRCLIP 12 2 4 10086 BOLT M6X12 1 5 22810 GASKET 6 1 6 10014 BOLT STUD M8X25 2 7 22407 BREATHER
More information3. LUBRICATION SYSTEM
3 3 LUBRICATION SYSTEM SERVICE INFORMATION------------------------------------------------ 3-2 TROUBLESHOOTING----------------------------------------------------- 3-2 ENGINE OIL/OIL FILTER ------------------------------------------------
More information365-SUB Engine : Engine Assembly 365-SUB [1/1] Page 1 of 5
Page 1 of 5 1 951-11012 Bolt 2 951-11054 Valve Cover 2 951-11054 1 Valve Cover 3 731-07059 Breather Hose 4 726-04101 Hose Clamp 6 N/A 1 Intake Valve Spring Seat 7 751-11124 Pivot Locking Nut 7 751-11124
More informationspare parts catalogue
spare parts catalogue Version 1.2013! IMPORTANT NOTICE! This engine is designed strictly for competition purposes only. The manufacturer SWISSAUTO declare that all spare parts and engines are not covered
More informationINDEX TECHNICAL SPECIFICATIONS 2 SPECIAL TOOLS 3-4 PERIODIC MAINTENANCE 5 LUBRICANTS 6 TROUBLESHOOTING 7-14 TIGHTENING TORQUE TABLE 15
INDEX TECHNICAL SPECIFICATIONS 2 SPECIAL TOOLS 3-4 PERIODIC MAINTENANCE 5 LUBRICANTS 6 TROUBLESHOOTING 7-14 TIGHTENING TORQUE TABLE 15 ENGINE DISASSEMBLY 16-24 ENGINE REASSEMBLY 25-37 SPECIAL 3-SHOE CLUTCH
More information3. Engine XCITING 400i. This chapter covers the location and servicing of the engine components for the KYMCO Xciting 400i.
3. Engine XCITING 400i Engine This chapter covers the location and servicing of the engine components for the KYMCO Xciting 400i. Engine Removal... 3-4~3-12 Cylinder Head Cover... 3-13~3-17 Camshaft...
More informationCYLINDER - CYLINDER HEAD
A1 CYLINDER - CYLINDER HEAD 1 3FA-11110-00-00 CYLINDER HEAD ASSEMBLY. 1 2 95612-06625-00. BOLT, STUD............. 2 3 22F-11134-10-00. GUIDE, EXHAUST VALVE... 2 4 93440-10109-00. CIRCLIP.................
More informationPARTS LIST CHAIN SAW G5000
848C8C93B1 (805) * PARTS LIST CHAIN SAW : 1. Use ZENOAH genuine parts specified in the parts list for repair and/or replacement. 2. ZENOAH does not warrant the machines, those which have been damaged by
More informationXL12 Chain Saw UT Page 1 of 21 Carburetor Chamber
XL12 Chain Saw UT-10080 Page 1 of 21 Carburetor Chamber XL12 Chain Saw UT-10080 Page 2 of 21 Carburetor Chamber 1 59274 1 GASKET- Spacer 2 59718 1 SPACER 3 63260A 1 RETAINER- Reed valve 4 63253 1 SEAT-
More informationLIFAN 125cc K-START ENGINE CATALOGUE
REF # PART # LIFAN 125cc K-START ENGINE CATALOGUE DESCRI PTI ON 1.Cylinder Head Cover qty per bike 1 12311/1P50FMG Cover, cylinder head 1 2 12240/1P50FMG Cover comp., cylinder head, RH 1 3 12242/1P50FMG-3
More informationCYLINDER HEAD. Ref. Part No. Number Description Qty Remarks
A1 A2 A3 A4 CYLINDER HEAD 1 3FA-11110-01-00 CYLINDER HEAD ASSY...... 1 2 90116-06541-00. BOLT, STUD............. 2 3 22F-11134-10-00. GUIDE, EXHAUST VALVE... 2 4 93440-10109-00. CIRCLIP.................
More informationCYLINDER - CRANKCASE. Ref. Part No. Number Description Qty Remarks
A1 CYLINDER - CRANKCASE 1 (374-15111-00-00) CRANKCASE 1............ 1 2 374-15121-02-00 CRANKCASE 2............ 1 3 99510-12016-00 PIN, DOWEL.............. 2 4 98580-06550-00 SCREW PAN HEAD (92503-06050).............
More information6000W Generator. 6000W Generator. 6000W Generator. 6000W Generator. Cylinder barrel. Cylinder head system assy. Description. APA Part No.
Cylinder head system assy. Cylinder barrel A APA Part No. B APGG000-A-0-JD HEAD COVER COMP. APGG000-B-0-JD (MX ) APGG000-A-0-JD HEAD COVER WASHER COMP. APGG000-B-0-JD OIL LEVEL SWITCH ASSY. APGG000-A-0-JD
More informationILLUSTRATED PARTS LIST MS330ECH PUMP/ENGINE PACKAGE. MS330ECH PUMP/ENGINE PACKAGE PART # REV12/01 Maruyama. E x t r a o r d i n a r y.
MARUYAMA ILLUSTRATED PARTS LIST PUMP/ENGINE PACKAGE PUMP/ENGINE PACKAGE PART #4540 REV1/01 Maruyama. E x t r a o r d i n a r y. ILLUSTRATED PARTS LIST MAIN BODY 7 5 1 1 0 9 4 17 11 15 14 3 1 1 19 5 1 9
More informationPREFACE. Combined with all the specialty and advantages of the same models from both domestic and abroad, 1P55FMJ is
PREFACE Combined with all the specialty and advantages of the same models from both domestic and abroad, PFMJ is one of the newly engines developed by our Co. It is characterized by strong power, low fuel-consumption
More informationG5200. Fig.1 POWER UNIT
CHAIN SAW 5200 Fig.1 POWER UNIT Fig.1 POWER UNIT Key# PART NUMBER DESCRIPTION NOTE 1 2880-12111 Cylinder 1 ø45 2 2880-14111 Inlet Pipe 1 3 2880-14120 Spring 5 2880-14150 Inner Guide 1 6 2670-14311 Bracket
More information1. GENERAL INFORMATION
GENERAL INFORMATION ENGINE SERIAL NUMBER ---------------------------------------------- - SPECIFICATIONS ---------------------------------------------------------- - 2 SERVICE PRECAUTIONS ------------------------------------------------
More informationPARTS LIST CHAIN SAW G455
848C8193B3 (801) *G455 PARTS LIST CHAIN SAW G455 : 1. Use ZENOAH genuine parts specified in the parts list for repair and/or replacement. 2. ZENOAH does not warrant the machines, those which have been
More informationPARTS LIST CHAIN SAW G455AVS G500AVS. (for Australia)
84818193B2-AUS (801) PARTS LIST CHAIN SAW (for Australia) : 1. Use ZENOAH genuine parts specified in the parts list for repair and/or replacement. 2. ZENOAH does not warrant the machines, those which have
More informationOwner s Manual. Parts List. Cylinder Head assy. APA Part No. Description Part. No
Cylinder Head assy. A SP-GG900E-A-01-JD HEAD COVER COMP. BOLT JF340-A-01 SP-GG900E-A-02-JD HEAD COVER WASHER COMP. JF340-A-02 SP-GG900E-A-03-JD TUBE JF340-A-13 SP-GG900E-A-04-JD HEAD COVER COMP. JF340-A-04
More informationCYLINDER HEAD CONTINUED ON NEXT FRAME. Ref. Part No. Number Description Qty Remarks
A1 CYLINDER HEAD 1 4JY-11111-00-00 HEAD, CYLINDER 1 (4JY-11111-01-00).......... 1 2 90116-08394-00 BOLT, STUD.............. 5 3 90176-08026-00 NUT, CROWN............. 5 4 90201-08087-00 WASHER, PLATE...........
More informationL&T MANUFACTURING, INC.
100-9 Aluminum Cover Assembly 76.50 100-10 Aluminum Cover 64.75 100-11 Cover Gasket (Rubber) 2.85 100-11-1 Cover Gasket (Paper) 3.00 100-12-1 Lever Weight 1 Disc 1.60 100-12-3 Lever Weight 3 Disc 1.60
More informationSXLAO Chain Saw UT Page 1 of 21 Carburetor Chamber
SXLAO Chain Saw UT-10045 Page 1 of 21 Carburetor Chamber SXLAO Chain Saw UT-10045 Page 2 of 21 Carburetor Chamber 1 59274 1 GASKET- Spacer 2 59718 1 SPACER 3 63260A 1 RETAINER- Reed valve 4 63253 1 SEAT-
More information21. BATTERY/CHARGING SYSTEM (After '05)
21. BATTERY/CHARGING SYSTEM (After '05) COMPONENT LOCATION 21-2 SYSTEM DIAGRAM (TRX450ER) 21-2 SERVICE INFORMATION 21-3 TROUBLESHOOTING 21-5 BATTERY (TRX450ER) 21-6 CHARGING SYSTEM INSPECTION (TRX450ER)
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List 0GC Gas Concrete Saw Effective January, 09 0 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject to change
More information2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 1 Removal Engine removal is not required for this procedure. CAUTION: Use fender
More informationK&T Saw Shop or
11-600013U PRO 10-10 04/75 to 04/77 IPL 92379A-R1 Page 1 of 18 Accessories 11-600013U PRO 10-10 04/75 to 04/77 IPL 92379A-R1 Page 2 of 18 Accessories 91090 Bar-16" Sprocket Nose 86979N Chain Asy-16" PM370
More information9/7/2014 F9.9MSHV 1997 / CYLINDER CRANKCASE Yamaha Motor Corporation, U.S.A. All rights reserved.
F9.9MSHV 997 Page of 45 9/7/04 F9.9MSHV 997 / CYLINDER CRANKCASE 04 Yamaha Motor Corporation, U.S.A. All rights reserved. F9.9MSHV 997 Page of 45 9/7/04 Part List F9.9MSHV 997 / CYLINDER CRANKCASE REF
More informationATV GOON 260 parti di ricambio agg. al
19 CYLINDER REF.No. CODICE RICAMBIO DESCRIZIONE 1 22401a CYLINDER HEAD ASSY 1 22401b CYLINDER HEAD ASSY (FOR ATV300) 1 2 22402 GUIDE INTAKE VALVE 2 3 10112 CIRCLIP 12 2 4 10086 BOLT M6X12 1 5 22405 GASKET
More information20.Cylinder Block. Cylinder Block A: REMOVAL ME(H4DOTC)-63 ST CRANKSHAFT STOPPER
Cylinder Block MECHANICAL 20.Cylinder Block A: REMOVAL Before conducting this procedure, drain engine oil completely. 1) Remove the intake manifold. 2)
More informationCYLINDER HEAD CONTINUED ON NEXT FRAME. Ref. Part No. Number Description Qty Remarks
A1 CYLINDER HEAD 1 4JY-11111-00-00 HEAD, CYLINDER 1 (4JY-11111-01-00).......... 1 2 90116-08394-00 BOLT, STUD.............. 5 3 90176-08026-00 NUT, CROWN............. 5 4 90201-08087-00 WASHER, PLATE...........
More informationK&T Saw Shop or
12-600031U PRO MAC 55 08/73 to 03/77 IPL 92384A-R1 Page 1 of 20 Accessories www.ktoutdoor.com 12-600031U PRO MAC 55 08/73 to 03/77 IPL 92384A-R1 Page 2 of 20 Accessories 84453 Kit - Piston tool 69191 Kit
More informationE-11-1 RECOIL STARTER (RAMMER)
E-11-1 RECOIL STARTER (RAMMER) 001 28400-Z0D-V02ZA STARTER ASSY., RECOIL *NH1* 1 002 28410-Z0D-V02ZA CASE COMP., RECOIL STARTER*NH1* 1 003 28421-Z0D-V02 REEL, RECOIL STARTER 1 004 28422-ZG0-W02 RATCHET,
More informationFINAL REDUCTION/TRANSMISSION SYSTEM
11 FINAL REDUCTION/ SERVICE INFORMATION------------------------------------------------ 11-2 TROUBLESHOOTING----------------------------------------------------- 11-2 SECONDARY DRIVE/DRIVEN BEVEL GEAR
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List RZ60/603GC Gas Concrete Saw Effective January 1, 2018 2017 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List RZ60/603GC Gas Concrete Saw Effective January 1, 2016 2016 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject
More informationReplacement Parts & Accessories Price List
Replacement Parts & Accessories Price List RZ60/603GC Gas Concrete Saw Effective January 1, 2016 2016 ICS, Blount International Inc. Supersedes all previous pricing. Specifications and pricing are subject
More informationDIAMO Discovery XLT PARTS CATALOG Engine First Edition August 2008
DIAMO Discovery XLT PARTS CATALOG - 500 Engine First Edition August 2008 Copyright 2007-2008 LS MotorSports, LLC. Reproduction without written permission is completely forbidden. The information and diagrams
More informationCONT ENTS 1 ABOUT THIS PARTS LIST CONTENTS-ENGINE GROUP CONTENTS-FRAME GROUP ENGINE PARTS LIST FRAME PARTS LIST...
CONT ENTS 1 ABOUT THIS PARTS LIST...... 2 2 CONTENTS-ENGINE GROUP... 3 3 CONTENTS-FRAME GROUP... 5 4 ENGINE PARTS LIST...... 9 5 FRAME PARTS LIST...... 45 1 ABOUT THIS PARTS LIST THIS PARTS LIST IS COMPILED
More informationShindaiwa Illustrated Parts List. 488 EC1 Chainsaw. CYLINDER / muffler... 2
Shindaiwa Illustrated Parts List 488 EC1 Chainsaw CYLINDER / muffler... 2 Crankcase... 3 CYLINDER Cover / Handles / Fuel Filter...4-5 Clutch / Oil Pump / Chain Cover...6-7 Piston / Crankshaft... 8 Rotor
More informationMAINTENANCE SXV / RXV
MAINTENANCE SXV / RXV 450-550 3.1.12. HANDLEBAR AND CONTROLS Screw securing clutch control to handlebar M6 10 Throttle control screw M6 4 Ignition switch screw M8 24 FOOTRESTS Footrest support bracket
More informationCHAINSAW PARTS CATALOG. CS-4400 Type 1E: & UP. ECHO, INCORPORATED 400 Oakwood Road Lake Zurich, Illinois MODEL: SERIAL NUMBERS. 43.
AVAILABLE ATTACHMENTS & ACCESSORIES 0 CHAIN - " 0 CHAIN - " 0 CHAIN - " 00 BAR - " 0 BAR - " 00 BAR - " 00 FIXED NOSE CASE PARTS CATALOG CHAINSAW.cc MODEL: SERIAL NUMBERS CS-00 Type E: 0 & UP ECHO, INCORPORATED
More information2012 Kia Soul L4 2.0L
2012 Kia Soul L4 2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Chain» Service and Repair» Repair Procedures» Part 2 Installation 1. The TDC marks of the intake and exhaust CVVT sprockets are
More information