Read all instructions before installing and using. Installer: This manual must be delivered to the end user.

Transcription

1 Installation Instructions Vacuum / Magnet Mount Kits IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.! WARNING! Failure to install or use this product according to manufacturers recommendations may result in property damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect! Do not install and/or operate this safety product unless you have read and understand the safety information contained in this manual. 1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure the safety of you and those you are seeking to protect. 2. Exercise caution when working with live electrical connections. 3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing, which can cause personal injury and/or severe vehicle damage, including fire. 4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing eye contact with the roadway. 5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people, vehicles or other obstructions. 6. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, driving against traffic, responding at a high rate of speed, or walking on or around traffic lanes. 7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device. INTRODUCTION: The Magnet Mount Kits offer a secure, temporary mount. The included adhesive disk(s) should be placed on the bottom of the magnet(s) to prevent scratching the vehicle finish upon installation. The light should be placed in the center of the roof where the least amount of curvature occurs. Before installing, make sure there is no debris on the bottom of the light or on the roof of the vehicle, which could reduce the holding power of the magnet. Place and remove the light without sliding to avoid scratching the paint on the vehicle. After placement, the light should adhere firmly to the surface. If the unit slides or moves easily, a proper installation has not been obtained. To protect the light and magnet mount assembly, return light to the box when not in use. Do not attempt to attach the light to an ice-covered surface. Note: The Magnet Mount is not recommended for use on a moving vehicle, nor is it intended as a permanent mount for the light. Long duration usage of the magnet in the presence of moisture will cause the steel to rust. The Vacuum-Magnet Mount kits feature a magnet(s) inside of the suction cup(s) for a secure, temporary mount. The light should be placed in the center of the roof where the least amount of curvature occurs. Before installing, make sure there is no debris on the bottom of the light or on the roof of the vehicle, which could reduce the holding power of the suction cup(s) and magnet(s). Place and remove the light without sliding to avoid scratching the paint on the vehicle. After placement, the light should adhere firmly to the surface. If the unit slides or moves easily, a proper installation has not been obtained. To release the vacuum, lift the tab to release the airlock. To protect the Vacuum-Magnet Mount assembly, return the light to the box when not in use. Do not attempt to attach the light to an ice-covered surface.! WARNING! Maximum recommended vehicle speed for safe operation using the Vacuum Mount model is 65 mph (104 km/h), when fitted to the center of a vehicle roof of steel construction. Higher speeds could cause the mount to fail, resulting in the beacon/minibar flying off of the vehicle, which could cause damage to your and other vehicles, and injury or death to the passengers. The Vacuum Mount is not intended as a permanent mounting for the beacon/minibar. Metallic debris collected by the Vacuum Mount will contribute to rust stains. Ensure that the Vacuum Mount is kept clean Rev. H Page 1 of 5

2 Vacuum Mount Installation for 5300 Series without brass five-position terminals: (Refer to Figures 1 and 2) 1. The faston/female spade connector is not needed for this model. 2. Remove lens. 3. Remove the three mounting screws for each motor/gear assembly, and move the assemblies off to the side, without disconnecting the wiring of the motor/gear assembly. If the reflector interferes with the removal of the mounting screws, reposition reflector by rotating the motor worm gear. Do not attempt to rotate the reflector itself. 4. Cut the red input power wire that enters the base through the cable routing hole as close to the wire connector as possible. 5. Remove the black wires with faston/spade connectors from the receptacles on the bottoms of both motor/gear assemblies (one each) as shown in Figure 1. Pull wires out through the cable routing hole and discard. 6. Route the end of the cord into the base, through the cable routing 7. Plug the black power wire from the cord into the open position on the six-position wire connector. 8. Feed the black with white lettering ground wire under the mirror (to prevent interference) and attach to the spade receptacle on the bottom of the motor/gear assembly as shown in Figure Realign the motor/gear assemblies onto the base, making sure the 6-position wire connector is placed beneath one of the motor/gear assemblies as originally assembled. 10. Secure one end of the 8 black wire with ring terminals under one of the MGA mounting screws as shown in Figure 1. Feed the 8 black wire under the mirror and secure the ring terminal on the other end of the wire under one of the mounting screws on the other MGA. Be careful to not over-tighten the 11. Install the zip-tie onto the cord inside the unit approximately one inch from the end of the cable. Trim excess. 12. Align the Vacuum Mount Assembly with the release tab to the outside corner as shown in Figure 2, so that the mounting holes match with the base. 13. Press the vacuum mount assembly into the embossed circle in the base and secure from the inside with the included self-tapping (machine screws for A5000VMK-NEO) mounting Be careful to not over-tighten the 14. Install the (4) rubber plugs into the unused mounting holes on each corner as shown in Figure Replace the lens and install the two lens mounting 16. Place the provided warning label on the lens, opposite the side with the product label. DETAIL OF A5000VMK-NEO Figure 2 Vacuum Mount Installation for 5300 Series with two brass five-position terminals: (Refer to Figure 3) 1. The 8 black wire with ring terminals and the zip-tie are not needed for this model. 2. Remove the lens by removing the two lens mounting screws, one at either end of the unit. 3. Remove the existing input power wires, by removing the 5 position terminals inside, and removing the fastons/spade connectors from the 5 position terminals. Pull wires out through the cable routing hole and discard. 4. Route the end of the cord into the base, through the cable routing 5. Route cable and leads under mirror and through the large strain relief on the positive (+) side. 6. Crimp the faston/spade connector onto the black power wire from the cord. Attach the faston/spade connector as shown, and replace the 5-position terminal. 7. Feed the ground (black with white lettering) wire under the mirror and attach to ground (-) as shown, and replace the 5-position terminal. 8. Align the Vacuum Mount Assembly with the release tab to the outside corner as shown, so that the mounting holes match with the base. 9. Press the vacuum mount assembly into the embossed circle in the base and secure from the inside with the included mounting 10. Install the (4) rubber plugs into the unused mounting holes on each corner as shown in Figure Replace the lens, & install the two lens mounting Figure Rev. H Page 2 of 5

3 CABLE ROUTING HOLE STRAIN RELIEF UNDER TERMINAL BLACK WIRE MAGNET ADHESIVE COVER POWER CABLE HEX NUT MAGNET ASSEMBLY BLACK WITH WHITE LETTERING WIRE INTERNAL STAR WASHER CUP MAGNET MOUNTING SCREW HEX NUT MOUNTING SCREWS (3) PLACES RUBBER PLUG (4) PLACES BASE WIRE ROUTING HOLE BASE VACUUM MOUNT UNIT Figure 4 Figure 3 DETAIL OF A5000VMK-NEO 5300 Series Magnet Mount Installation: (Refer to Figure 4) 1. Refer to the appropriate Vacuum Mount Installation for 5300 Series, steps 1 through 11 and the corresponding Figures for wiring instructions for the cord. 2. Replace lens and install the two lens mounting 3. Place an internal star washer onto the enclosed M5 x 20 hex bolt and insert the hex bolt through the hole in the cup magnet as shown. Apply a hex nut to the bolt by threading it on the bolt until the nut is flush with the end of the bolt. Hold the magnet/bolt/nut assembly with the bolt extended through the magnet as far as possible and feed the hex nut and the shank of the bolt through one of the keyhole openings at the 4 corners of the underside of the lightbar base. Slide the bolt shank along the keyway slot until the nut can be pulled and seated into the hex shaped retaining cavity. Maintain tension on the bolt/nut by holding onto the cup magnet while tightening the assembly. Repeat this process for all four corners. 4. Place the adhesive magnet covers over the magnets. Vacuum Mount Installation for 5700 Series without a brass five-position terminal: (Refer to Figure 1) 1. Twist off the lens. 2. Remove the three mounting screws for the motor/gear assembly, and move the assembly off to the side, without disconnecting the wiring of the motor/gear assembly. If the reflector interferes with removal of the motor/gear assembly, reposition reflector by rotating the motor worm gear. Do not attempt to rotate the reflector itself. 3. Cut the red input power wire that exits the base as close to the four-position wire connector as possible. Remove the black wire by disconnecting the faston/spade connector from the receptacle on the bottom of the motor/gear assembly as shown in Figure 1. Pull wires out through the cable routing hole and discard. 4. Route the end of the cord into the base, through the cable routing 5. Plug the black power wire from the cord into the open position on the four-position positive wire connector. 6. Attach the black with white lettering ground wire with the faston/ spade connector to the receptacle on the bottom of the motor/gear assembly as shown in Figure Install the zip-tie onto the cord inside the unit approximately one inch from the end of the cable. Trim excess. 8. Reinstall the motor/gear assembly. If there is a black wire attached to the motor, secure its ring terminal under one of the MGA mounting 9. Align the Vacuum Mount Assembly with the mounting holes in the base, and secure from the inside with the included self-tapping mounting Be careful to not over-tighten the 10. Replace the lens Rev. H Page 3 of 5

4 Vacuum Mount Installation for 5700 Series with two brass five-position terminal: (Refer to Figure 5) 1. The zip-tie is not needed for this model. 2. Twist off the lens. 3. Remove the three mounting screws for the motor/gear assembly, and move the assembly off to the side, without disconnecting the wiring of the motor/gear assembly. 4. Remove the existing power input wires by removing the 5 position terminals inside, and removing the fastons/spade connectors from the 5 position terminals. 5. Route the end of the cord into the base, through the cable routing 6. Route the cable and leads through the strain relief features as shown. 7. Crimp the faston/spade connector provided in this kit onto the black power wire from the cord. Attach the fastons/spade connectors to the 5 position terminals as shown, and replace the terminals. 8. Replace the motor/gear assembly. 9. Align the Vacuum Mount Assembly with the mounting holes in the base, and secure from the inside with the included mounting 10. Replace the lens. BLACK LEAD TERMINAL RED LEAD NOTE: MOTOR/GEAR ASSEMBLY NOT SHOWN FOR CLARITY COIL CORD MOUNTING SCREW (3) PLACES O RING O RING GROOVE VACUUM MOUNT ASSEMBLY Figure 5 ADHESIVE GASKET MAGNET MAGNET COVER 5700 Series Magnet Mount Installation: (Refer to Figure 6) 1. The faston/female spade connector is not needed for this model. 2. Refer to the appropriate Vacuum Mount Installation for 5700 Series section steps 1 through 8 and the corresponding Figures for wiring instructions for the cord. 3. Replace the lens. 4. Peel off protective paper from one side of adhesive gasket, and apply to the back of the metal magnet cup. 5. Peel off paper from other side of the adhesive gasket and apply magnet assembly to the center of the bottom of the base covering the pipe mount feature. 6. Place the plastic magnet cover over the magnet. Figure Rev. H Page 4 of 5

5 Manufacturer Limited Warranty and Limitation of Liability: Manufacturer warrants that on the date of purchase this product will conform to Manufacturer s specifications for this product (which are available from the Manufacturer upon request), and Manufacturer further warrants that this product is free from defects in materials and workmanship. This Limited Warranty extends for twelve (12) months from the date of purchase. Other warranties may apply; call Manufacturer for details. Manufacturer will, at its discretion, repair or replace any product found by the Manufacturer to be defective and subject to this Limited Warranty. DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAP- PROVED MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAIN- TAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY. ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT THAT MAY HAVE BEEN MADE BY SALESPEOPLE, DEAL- ERS, AGENTS OR OTHER MANUFACTURER S REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES. THIS LIMITED WAR- RANTY MAY NOT BE AMENDED, MODIFIED, OR ENLARGED EXCEPT BY A WRITTEN AGREEMENT SIGNED BY AN AUTHO- RIZED OFFICIAL OF MANUFACTURER WHICH EXPRESSLY REFERS TO THIS LIMITED WARRANTY. Exclusion of Other Warranties: MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANT- ABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT. BUYER S SOLE AND EXCLUSIVE REMEDY IN CONTRACT, TORT, OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE THE REPLACEMENT OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE. Limitation of Liability: IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO THE MANUFACTURER S PRODUCTS, MANUFACTURER S LIABILITY FOR DAMAGES SHALL BE LIMITED TO THE AMOUNT PAID FOR THE PRODUCT AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CON- SEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLA- TION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER S REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABIL- ITY WITH RESPECT TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT. This Limited Warranty defines specific legal rights. You may have other legal rights, which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages. 833 West Diamond St Boise, Idaho Customer Service USA UK +44 (0) AUS +61 (0) ECCO Rev. H Page 5 of 5