COMPACT HYDRAULIC PUNCHER

Size: px
Start display at page:

Download "COMPACT HYDRAULIC PUNCHER"

Transcription

1 INSTRUCTION MANUAL COMPACT HYDRAULIC PUNCHER Art DIN EN ISO 9001 QZERTIFIKAT...convincing solutions

2 1. TECHNICAL CHARACTERISTICS Maximum cutting capacity: Ø 60 mm. 3 mm thick steel plate 46 x 46 mm. 2 mm thick steel plate Material Max yield strength: 37 kg / mm 2 Cutting force: 50 KN Operating pressure: 650 bar Dimensions: 290 x 140 mm Weight: 2.4 kg Box: Tool composition: 330 x 190 x h 75 mm 1 PHC-60 Compact hydraulic puncher 2 M10 stud bolts 1 M20 stud bolt 1 spacer 1 M20/10 reducer 1 metal transport box 2. OPERATING RANGE mm thick sheet metal, 370 N/mm 2 yield strength Standard dimensions PG TYPE: PG-9 Ø 15.2 mm PG-29 Ø 37 mm PG-11 Ø 18.6 mm PG-36 Ø 47 mm PG-13 Ø 20.4 mm PG-42 Ø 54 mm PG-16 Ø 22.5 mm PG-48 Ø 60 mm PG-21 Ø 28.3 mm B.CETACIII Ø 65 mm PILOT Ø 30.5 mm Standard dimensions METRIC TYPE: M-16 Ø 16.5 mm M-40 Ø 40.5 mm M-20 Ø 20.5 mm M-50 Ø 50.5 mm M-25 Ø 25.5 mm M-63 Ø 63.5 mm M-32 Ø 32.5 mm Customised dimensions from a minimum diameter of Ø 15 mm to a maximum diameter of Ø 60 mm mm thick sheet metal, 370 N/mm 2 yield strength Standard SQUARE dimensions (FOR AMMETERS): AMP x 46 mm Customised dimensions from a minimum of 18 x 18 mm to a maximum of 46 x 46 mm after prior consultation. 2

3 english 3. OPERATING INSTRUCTIONS 3.1. OPERATION This lightweight, user-friendly PHC-60 Compact Hydraulic Puncher is the ideal option for both on-site and factory shop work. This tool is a must for all skilled workers specialising in the assembly of aluminium, steel plate or plastic switching panels, regardless of whether the surface is painted or not. Stud 3.2. TO OPERATE Prior drilling. Use a drill to make an initial Ø 11 mm hole in the plate Punch to be punched. Die Shim Mount the draw studs and spacers Mount the M20/10 reducing stud on the tool, screwing it right down to the bottom. Locate the spacers on the stud and then mount the die. Insert the projecting part of the M10 stud into the hole drilled in the plate. Screw the punch into the M10 stud until it comes to a stop against the plate to be punched. Turn the pressure/depressure wheel clockwise, closing the hydraulic circuit, so that the tool is ready to perform the punching operation. convincing solutions Germany: HAUPA, Königstr , Remscheid Phone: +49 (0) , Fax: +49 (0) , sales@haupa.com Errors and technical changes reserved. 3

4 Punching operation Put the pressure/depressure wheel in the pressure position. Actuate the drive lever in a swinging movement until the plate has been punched. Once the punching has been completed, actuate the lever 2 or 3 times more until the cut piece of plate has completely separated. Then perform the operations in the reverse order. In other words, turn the compression / decompression wheel anticlockwise, unscrew the punch from the stud. The cut piece will easily come out of the die Making holes greater than Ø 31 mm. Perform the above-mentioned operations until a hole of Ø 20.4 mm minimum has been made. Unscrew the M10 stud and the M20/10 reducer Screw in the M20 stud until it comes to a stop. Insert the spacer on the shaft Mount the die on the spacer and insert the rest of the shaft through the Ø 20.4 mm hole. Screw the punch onto the M20 stud until it comes to a stop against the sheet metal and then proceed to punch, as indicated in the points above Making square or rectangular holes To make these holes, proceed as for the previous point (point 3.2.4). 4

5 english 4. CARE AND MAINTENANCE The tool maintenance must be performed by technical personnel qualified in hydraulic systems CLEANING If the tool is adequately cleaned after use, particularly the mobile parts, this will help to lengthen its useful life. Remember that dust, sand, environmental conditions particularly with a high salt index and dirt in general are all extremely harmful for hydraulic tooling. Particular care needs to be taken when cleaning both the pump drive piston and the compression piston since any impurities could scratch the cylinder walls and damage the leaktight seals. To clean the pistons correctly, in this case, we would recommend advancing the piston and then cleaning it with a high quality non-corrosive solvent STORAGE In order to prevent damage to the tools, caused by impact, dust etc, we would recommend storing the tools in their transport and storage cases OIL LEVEL Periodically and particularly after extended use, it is advisable to check the oil reservoir level and add oil when required Refilling the oil reservoir Unscrew the reservoir plug located at the end of the fixed handle With the machine in an upright position, refill with thoroughly clean, filtered hydraulic oil until it is 2 or 3 cm from the top. Important: the hydraulic oil must be filtered, have an ISO grade viscosity of 15, a viscosity index of 100 and conform to the AFNOR NFE HM and ISO 6743/4 L-HM standards Punch, Die and Stud lubrication For extended punch and die duration and to use less force, it is advisable to lubricate the punch and die cutting edges with a little oil. This will also facilitate the detachment of the knockout WARNING! Particular care should be paid to ensure that the punch is screwed right into the stud, in order to prevent the stud or thread from breaking, and also to prevent the tool from reaching the end of its travel limit without having cut right through the sheet. convincing solutions Germany: HAUPA, Königstr , Remscheid Phone: +49 (0) , Fax: +49 (0) , sales@haupa.com Errors and technical changes reserved. 5

6 5. FAULT DIAGNOSTICS ATTENTION: If you should require any service other than those detailed below, please consult the nearest Technical Service Centre The tool piston does not retract completely The tool does not complete its stroke at a particular operating position. Solution: Refill the reservoir with oil Solution: Change the o-rings, this must be performed by qualified personnel The tool piston does not retract to its home position Piston spring fatigued or damaged. Solution: Replace the spring Oil deteriorated or dirty. Solution: Send the tool to the nearest Technical Service Centre. In all cases, we would advise sending the machine to the nearest Technical Service centre for repair. Always use original spares. Any other part type could seriously damage the tool and would void the guarantee. If despite the above, the tool still does not work correctly, return it to the nearest Technical Service for repair and fine tuning by specialised personnel or send an to: info@haupa.com 6

7 english Code nº Nº DESCRIPTION QTY Code nº Nº DESCRIPTION QTY HARD RING BODY O-RING O-RING CYLINDER BODY SPRING O-RING BALL HARD RING INLET VALVE PISTON INLET TUBE HARD RING FILTER SUPPORT O-RING 1 E FILTER SPRING RESERVOIR NON-RETURN VALVE O-RING SPRING RESERVOIR PLUG BALL PACKING NUT O-RING M10 DRIVE AXLE SPACER M20 DRIVE AXLE LEVER SUPPORT M20/M10 DRIVE AXLE CIRCLIPS PIN OPERATING LEVER O-RING HARD RING SEAL SPRING DRIVE PISTON PIN BALL O-RING RELEASE VALVE KEY 1 WITH EVERY REPLACEMENT PART ORDER, INCLUDE THE FOLLOWING INFORMATION: 1) Article number. 2) Article description. 3) Reference to the operating instructions and/or date. 4) Tool type. 5) Serial number of the tool. The guarantee is voided if you use parts that are not original replacement parts from HAUPA. convincing solutions Germany: HAUPA, Königstr , Remscheid Phone: +49 (0) , Fax: +49 (0) , sales@haupa.com Errors and technical changes reserved. 7

8 8 EXPLODED VIEW DRAWING Art. NO

Hydraulic terminal crimping tool. Art / QZERTIFIKAT DIN EN ISO convincing solutions

Hydraulic terminal crimping tool. Art / QZERTIFIKAT DIN EN ISO convincing solutions Hydraulic terminal crimping tool Operating Instructions Hydraulic terminal crimping tool Art. 21 57 55 / 21 57 60 DIN EN ISO 9001 QZERTIFIKAT...convincing solutions 1. TECHNICAL CHARACTERISTICS Field of

More information

english Die holder Pushbutton to advance Pushbutton for return movement

english Die holder Pushbutton to advance Pushbutton for return movement Hydraulic pliers INSTRUCTION MANUAL Electro-hydraulic crimping tools AC25-12 Art. 216601 TC25-12 Art. 216620 AC42-12 Art. 216622 TC42-12 Art. 216624 DIN EN ISO 9001 QZERTIFIKAT 1. Technical data Area of

More information

AS AS SAS6-85

AS AS SAS6-85 Hydraulic cutting tools INSTRUCTION MANUAL Electro-hydraulic cable cutters AS6-40 Art. 216422 AS6-52 Art. 216424 Video 216428 AS6-85 Art. 216428 Video 216430 SAS6-85 Art. 216430...convincing solutions

More information

Electro-hydraulic crimping tool AH-12. Art convincing solutions. Video

Electro-hydraulic crimping tool AH-12. Art convincing solutions. Video Hydraulic crimping tools INSTRUCTION MANUAL Electro-hydraulic crimping tool AH-12 Art. 216503 Video 216503... convincing solutions 1. Technical data Area of application: For the creation of an electrical

More information

INSTRUCTION MANUAL. Battery powered crimping tool SMART-LINE. Battery powered crimping tool SO-6M. Art /M. convincing solutions.

INSTRUCTION MANUAL. Battery powered crimping tool SMART-LINE. Battery powered crimping tool SO-6M. Art /M. convincing solutions. Battery powered crimping tool SMART-LINE INSTRUCTION MANUAL Battery powered crimping tool SO-6M Art. 216801/M Video 216801/M convincing solutions 1. Technical data Area of application: For the creation

More information

Electro-hydraulic crimping tools SD300-6M / SD400-6M. Art /M / /M. convincing solutions. Video /M Video /M

Electro-hydraulic crimping tools SD300-6M / SD400-6M. Art /M / /M. convincing solutions. Video /M Video /M Electro-hydraulic SMART crimping tools INSTRUCTION MANUAL Electro-hydraulic crimping tools SD300-6M / SD400-6M Art. 216663/M / 216667/M Video 216663/M Video 216667/M convincing solutions 1. Technical data

More information

Battary powered cutting tool. AS6-S32 Art convincing solutions. Video

Battary powered cutting tool. AS6-S32 Art convincing solutions. Video Hydraulic cutting tool Smart Line Operating instructions Battary powered cutting tool AS6-S32 Art. 216419 Video 216419 convincing solutions 1. Technical data Area of application: Separating copper and

More information

Battery powered cutting tool. AS6ST-20 Art convincing solutions. Video

Battery powered cutting tool. AS6ST-20 Art convincing solutions. Video Hydraulic cutting tool Smart Line Operating instructions Battery powered cutting tool AS6ST-20 Art. 216418 Video 216418 convincing solutions 1. Technical data Area of application: Separating copper and

More information

Hydraulic hand-punching tool HS-6. Art convincing solutions

Hydraulic hand-punching tool HS-6. Art convincing solutions Hydraulic punching tools INSTRUCTION MANUAL Hydraulic hand-punching tool HS-6 Art. 217602 convincing solutions Contents 1 Technical Data Page 2 2 Safety Instructions Page 2 3 Tool Operation Page 3 3 Tool

More information

INSTRUCTIONS & MAINTENANCE SHEET PORTABLE BATTERY HYDRAULIC POWERPACK HAB1102

INSTRUCTIONS & MAINTENANCE SHEET PORTABLE BATTERY HYDRAULIC POWERPACK HAB1102 INSTRUCTIONS & MAINTENANCE SHEET PORTABLE BATTERY HYDRAULIC POWERPACK HAB1102 LARZEP, S.A. Avenida Urtiaga, 6 48269 MALLABIA, SPAIN Tel. +34 943 171200 Fax. +34 943 174166 e-mail: sales@larzep.com www.larzep.com

More information

INSTRUCTIONS & MAINTENANCE SHEET PORTABLE BATTERY HYDRAULIC POWERPACK HAB1101

INSTRUCTIONS & MAINTENANCE SHEET PORTABLE BATTERY HYDRAULIC POWERPACK HAB1101 INSTRUCTIONS & MAINTENANCE SHEET PORTABLE BATTERY HYDRAULIC POWERPACK HAB1101 LARZEP, S.A. Avenida Urtiaga, 6 48269 MALLABIA, SPAIN Tel. +34 943 171200 Fax. +34 943 174166 e mail: sales@larzep.com www.larzep.com

More information

» SCREW-HOLE PUNCHES

» SCREW-HOLE PUNCHES » SCREW-HOLE PUNCHES Screw-hole Cuts holes in thin materials quickly, easily, cleanly and without burrs in a few simple operations. Three-point cut gives improved contact and thus less deformation of the

More information

EQUALIZER International Limited 10T(I) Integral Hydraulic Spreading Wedge Repair Instruction Manual

EQUALIZER International Limited 10T(I) Integral Hydraulic Spreading Wedge Repair Instruction Manual EQUALIZER International Limited 10T(I) Integral Hydraulic Spreading Wedge Repair Instruction Manual INDEX THE EQUALIZER 10T(I) Integral Hydraulic Wedge SECTION CONTENTS PAGE NO (S) 03 04 05 06 07 08 09

More information

Around the cable. Socket sleeves.... convincing solutions

Around the cable. Socket sleeves.... convincing solutions Around the cable Socket sleeves... convincing solutions Socket sleeves (male and female) Socket sleeves (female) with cable stop bare brass not insulated, to DIN 46247/part 1-3 and similar Art. no. CSS

More information

Battery-powered hydraulic punch driver with 360 rotating head

Battery-powered hydraulic punch driver with 360 rotating head www.klauke.com LS 50-L FLEX Battery-powered hydraulic punch driver with 360 rotating head LS 50-L FLEX Battery-powered hydraulic punch driver Flexible and light. Flexible aluminium head 360 rotating head

More information

ALFRA Akku-Compact Flex Handstanze Art.-Nr / Prod.-No / N art / Nº de prod

ALFRA Akku-Compact Flex Handstanze Art.-Nr / Prod.-No / N art / Nº de prod Bedienungsanleitung / Operation Instructions / Manuel d'utilisation / Manual de instrucciones ALFRA Akku-Compact Flex Handstanze Art.-Nr. 02082 / Prod.-No. 02082 / N art. 02082 / Nº de prod. 02082 Elektrohydraulische

More information

OWNER S MANUAL PRODUCT CODE: 2006T

OWNER S MANUAL PRODUCT CODE: 2006T Jul-18 Product Code: 2006T OWNER S MANUAL PRODUCT CODE: 2006T HYDRAULIC PIPE BENDER 12,000KG Model Capacity Bending Die No of Attachments 12,000kg 1/2", 3/4", 1", 1-1/4", 1-1/2", 2" 6 Made in China to

More information

6602LP CAPACITY: 2 TON LOW RIDER SERVICE JACK

6602LP CAPACITY: 2 TON LOW RIDER SERVICE JACK CONTENTS: Page 1 Specifications 2 Warning Information 3 Setup Instructions 4 Operating Instructions, Preventative Maintenance, Inspection and Proper Storage 5 Hydraulic Jack Maintenance Guide and Regular

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 970-973 FORD MUSTANG (DRUM / DISC SPINDLE) PART NUMBER GROUP 0-905 WARNING INSTALLATION OF THIS KIT SHOULD ONLY

More information

ABSOLUTE EQUIPMENT PTY LTD

ABSOLUTE EQUIPMENT PTY LTD Manual Hydraulic Toe Jack Model DTJ Series ABSOLUTE EQUIPMENT PTY LTD 2/186 Granite Street, GEEBUNG QLD 4034 Australia sales@absoluteequipment.com.au Phone: +61 7 3865 4006 Fax: +61 7 3102 6288 This is

More information

ABSOLUTE EQUIPMENT PTY LTD

ABSOLUTE EQUIPMENT PTY LTD Manual Hydraulic Toe Jack Model DTJ Series ABSOLUTE EQUIPMENT PTY LTD 2/186 Granite Street, GEEBUNG QLD 4034 Australia sales@absoluteequipment.com.au Phone: +61 7 3865 4006 Fax: +61 7 3102 6288 This is

More information

CATALOG. Actuated Diaphragm Valve DN PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL.

CATALOG. Actuated Diaphragm Valve DN PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL. CATALOG Actuated Diaphragm Valve DN 15-100 PVC-U / PVC-C / PP-H / PVDF / ABS SMART IN FLOW CONTROL. TABLE OF CONTENTS Type 186 - DN 12-15 (MA 10) 04 General information - Technical specification 04 Sectional

More information

Machine elements. Pneumatic stamping unit. Toggle-lever presses

Machine elements. Pneumatic stamping unit. Toggle-lever presses Machine elements Pneumatic stamping unit Toggle-lever presses Machine elements ST 1292 ST 1092 Page 7.03 ST 9041 Page 7.04 ST 9061/62 Page 7.05 ST 9067 Page 7.05 ST 9070/72 Page 7.06 ST 9075 Page 7.07

More information

Instruction Manual FOLDABLE CRANE. NOTE: Owner / Operator must read and understand this. instruction manual before using the foldable crane.

Instruction Manual FOLDABLE CRANE. NOTE: Owner / Operator must read and understand this. instruction manual before using the foldable crane. Instruction Manual FOLDABLE CRANE NOTE: Owner / Operator must read and understand this instruction manual before using the foldable crane. - 1 - Specifications Model SC500 SC1000 SC2000 Capacity (kg) 500

More information

Safety instructions. Always... Never... Fire hazard! Dear customer,

Safety instructions. Always... Never... Fire hazard! Dear customer, Dear customer, Safety instructions Danger can occur when working with this punch driver due to improper handling and/or poor maintenance, which may damage the device and cause severe physical injuries.

More information

Mounting and Operating Instructions EB 8097 EN. Type and Type Pneumatic Control Valves

Mounting and Operating Instructions EB 8097 EN. Type and Type Pneumatic Control Valves Type 3347-1 and Type 3347-7 Pneumatic Control Valves Type 3347-7, cast body with welding ends Type 3347-7, bar stock body with threaded connections Mounting and Operating Instructions EB 8097 EN Edition

More information

A408 GB. Pneumatic oil and diesel pumps 1:1

A408 GB. Pneumatic oil and diesel pumps 1:1 03 594 A408 GB Pneumatic oil and diesel pumps 1:1 G Operating instructions for Pneumatic oil and diesel pump 1:1 Contents 1. General details 2 1.1 Intended use 2 1.2 Design and functional description 2

More information

BPLT62BSCR and BPLT62500BSCR

BPLT62BSCR and BPLT62500BSCR BPLT62BSCR and BPLT62500BSCR Battery Operated Hydraulic Crimping Tool Operating Instruction Manual IMPORTANT: Read and understand all of the instructions and safety information in this manual before operating

More information

Instruction Manual. Maximum Operating Pressure 700 bar

Instruction Manual. Maximum Operating Pressure 700 bar Remote Hydraulic Cutter Model HC-120R Maximum Operating Pressure 700 bar ABSOLUTE EQUIPMENT PTY LTD 2/186 Granite Street, GEEBUNG QLD 4034 Australia sales@absoluteequipment.com.au Phone: +61 7 3865 4006

More information

Marzocchi Suspension MZ I MZ I. Technical instructions

Marzocchi Suspension MZ I MZ I. Technical instructions Technical instructions Exploded view - MZ I - 100 Rif. Code Quantity Spare part list - MZ I - 100 Rif. Code Description Q.ty in the model Technical characteristics: Technical characteristics Single-crown

More information

2 TON CAPACITY PROFESSIONAL SERIES ALUMINUM JACK OWNER'S MANUAL SPECIFICATIONS

2 TON CAPACITY PROFESSIONAL SERIES ALUMINUM JACK OWNER'S MANUAL SPECIFICATIONS 80006 OWNER'S MANUAL CONTENTS: Page 1 Specifications 2 Warning Information 3 Setup, Operating and Preventative Maintenance 4 Troubleshooting 5 Maintenance 6 Exploded View Drawing and Replacement Parts

More information

2.- HANDLING OF VALVES BEFORE ASSEMBLY 3.- FITTING THE VALVE TO THE REST OF THE ASSEMBLY 5.- PERIODICAL INSPECTION OF THE VALVE AND MAINTENANCE

2.- HANDLING OF VALVES BEFORE ASSEMBLY 3.- FITTING THE VALVE TO THE REST OF THE ASSEMBLY 5.- PERIODICAL INSPECTION OF THE VALVE AND MAINTENANCE Page 1 of 16 CONTENTS 1.- INTRODUCTION 2.- HANDLING OF VALVES BEFORE ASSEMBLY 3.- FITTING THE VALVE TO THE REST OF THE ASSEMBLY 4.- OPERATION OF A BALL VALVE 5.- PERIODICAL INSPECTION OF THE VALVE AND

More information

Battery powered crimping tool

Battery powered crimping tool Battery powered crimping tool INSTRUCTION MANUAL Battery powered crimping tool SDE240-6M Art. 216669/M Video 216669/M DIN EN ISO 9001 ZERTIFIKAT... convincing solutions Art. OUTPUT VOLTAGE WEIGHT DIMENSION

More information

INTRODUCTION Please read this manual before you use your jack and ensure you understand its operation and the safety procedures to be observed.

INTRODUCTION Please read this manual before you use your jack and ensure you understand its operation and the safety procedures to be observed. Rated Capacity: 4000kg Closed Height: 19.5cm (approx) Hydraulic Lift: 11.8cm (approx) Maximum Extended Height: 6cm (approx) 4 Tonne Bottle Jack Instruction Manual Item Code: 332343 Model T90404 INTRODUCTION

More information

LS100L Battery-powered Punch Driver

LS100L Battery-powered Punch Driver OPERATION MANUAL Serial Number GATOR LS100L Battery-powered Driver Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this

More information

Instruction Manual FORKLIFT JACK. CAPACITY: 7000kgs

Instruction Manual FORKLIFT JACK. CAPACITY: 7000kgs Instruction Manual FORKLIFT JACK HFJ-700A CAPACITY: 7000kgs NOTE: Owner / Operator must read and understand this instruction manual before using the forklift jack. contents 1. SPECIFICATIONS-----------------------------------2

More information

Mounting and Operating Instructions EB 8039 EN. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve

Mounting and Operating Instructions EB 8039 EN. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Type 3351 Pneumatic On/off Valve Version with handwheel Mounting and Operating Instructions EB 8039 EN Edition May 2016 Definition of signal

More information

Pneumatic actuator Assembly & maintenance procedures

Pneumatic actuator Assembly & maintenance procedures Pneumatic actuator Assembly & maintenance procedures SPRING RETURN ACTUATOR Fig.7901 DOUBLE ACTING ACTUATOR Fig.7902 - LCIE 05 AR 022 2 CONTENTS 1. Applicable Range... page 4-6 2. General Information...

More information

NAF-Duball ball valves Maintenance and installation instructions List of spare parts

NAF-Duball ball valves Maintenance and installation instructions List of spare parts NAF-Duball ball valves Maintenance and installation instructions List of spare parts Fi 41.61(4)GB 08.01 Contents SAFETY General 1 Lifting 2 Receiving inspection 3 Installation 4 Flange gaskets 5 Starting

More information

Standard Knockout Punches 10. Punch Kits for Hydraulic Drivers 11. Draw Stud Selection Guide 13, 14, 18. Special Shape Punches

Standard Knockout Punches 10. Punch Kits for Hydraulic Drivers 11. Draw Stud Selection Guide 13, 14, 18. Special Shape Punches 8 Punching Tools, Hole Saws, Step Bits Page Punching Tools Standard Knockout Punches 10 Slug Buster Knockout Punches 10 Slug Splitter Knockout Punches 10, 12 Punch Kits for Hydraulic Drivers 11 Draw Stud

More information

Hydronic Corporation

Hydronic Corporation Hydronic Corporation Air Driven Hydraulic Pumps and Intensifiers P825 Installation, Use and Maintenance Manual Contents Introduction, Guarantee and Identification Plate Description, Start Up Procedures

More information

Battery powered crimping tool

Battery powered crimping tool Battery powered crimping tool INSTRUCTION MANUAL Battery powered crimping tool SDE240-6 Art. 216669 SPECIFICATION Art. 216669 OUTPUT VOLTAGE WEIGHT DIMENSION ACCESSORY APPLICATION CRIMPING RANGE 6t 18

More information

VESTIL MANUFACTURING CORP. OPERATION & SERVICE MANUAL PORTABLE DRUM JACK (DRUM-55-S) 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703

VESTIL MANUFACTURING CORP. OPERATION & SERVICE MANUAL PORTABLE DRUM JACK (DRUM-55-S) 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 OPERATION & SERVICE MANUAL PORTABLE DRUM JACK (DRUM-55-S) VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868 FAX:

More information

20 TONNE HYDRAULIC PRESS MODEL NO: CSA20FBT

20 TONNE HYDRAULIC PRESS MODEL NO: CSA20FBT 20 TONNE HYDRAULIC PRESS MODEL NO: CSA20FBT PART NO: 7614058 OPERATION & MAINTENANCE INSTRUCTIONS WARNING: Read these instructions before using the press GC0516 INTRODUCTION Thank you for purchasing this

More information

50 TONNE HYDRAULIC PRESS MODEL NO: CSA50FP

50 TONNE HYDRAULIC PRESS MODEL NO: CSA50FP 50 TONNE HYDRAULIC PRESS MODEL NO: CSA50FP PART NO: 7615202 OPERATION & MAINTENANCE INSTRUCTIONS WARNING: Read these instructions before using the press GC0516 INTRODUCTION Thank you for purchasing this

More information

Starting up hydraulic systems

Starting up hydraulic systems General / Installation A hydraulic system that operates economically, safely, and trouble-free requires careful planning, as well as proper installation and start-up. Conscientious maintenance has a considerable

More information

ADVANCED LINE. All airmotors can also be used without lubrication.

ADVANCED LINE. All airmotors can also be used without lubrication. Screwdriving technology Automation Air motors Air tools ADVANCED LINE Stainless Steel Air s from 20 W / 0.03 Hp up to 1.2 kw / 1.6 Hp NEW MOTOR RANGE High torque motors made from stainless steel: Our ADVANCED

More information

BPI42CR and BPI42300CR

BPI42CR and BPI42300CR BPI42CR and BPI42300CR Battery Operated Hydraulic Crimping Tool Operating Instruction Manual IMPORTANT: Read and understand all of the instructions and safety information in this manual before operating

More information

BUTTERFLY VALVE WITH WELDED ENDS INSTALLATION AND MAINTENANCE MANUAL

BUTTERFLY VALVE WITH WELDED ENDS INSTALLATION AND MAINTENANCE MANUAL BUTTERFLY VALVE 31300 SERIES INSTRUCTIONS FOR INSTALLATION, USE AND MAINTENANCE 1. Overview Read these instructions carefully before starting the valve installation and start-up work. Safe keep the instructions

More information

Mounting plates with predrilled holes for mounting angles Mounting kits Slider... Slider SK-V 20...

Mounting plates with predrilled holes for mounting angles Mounting kits Slider... Slider SK-V 20... Table of contents Product catalogue 2005... 1 Georg Fischer Transportation Engineering... 4 Fifth wheels... 5 Fifth wheels... 6 20t imposed load... 7 SK-S 36.20 PLUS (standard)... 7 Spare parts SK-S 36.20

More information

Instruction Manual. Single Acting, Aluminium, Locking Collar Hydraulic Cylinders ARSLC Series. Maximum Operating Pressure 700 bar

Instruction Manual. Single Acting, Aluminium, Locking Collar Hydraulic Cylinders ARSLC Series. Maximum Operating Pressure 700 bar Single Acting, Aluminium, Locking Collar Hydraulic Cylinders ARSLC Series Maximum Operating Pressure 700 bar ABSOLUTE EQUIPMENT PTY LTD 2/186 Granite Street, GEEBUNG QLD 4034 Australia sales@absoluteequipment.com.au

More information

Marzocchi Suspension MZ III MZ III. Technical instructions

Marzocchi Suspension MZ III MZ III. Technical instructions Technical instructions Exploded view - MZ III - 100 Rif. Code Quantity Spare part list - MZ III - 100 Rif. Code Description Q.ty in the model Technical characteristics: Technical characteristics Single-crown

More information

LC I LIPPERT COMPONENTS HYDRAULIC FULL WALL SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL

LC I LIPPERT COMPONENTS HYDRAULIC FULL WALL SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL LC I LIPPERT COMPONENTS HYDRAULIC FULL WALL SLIDEOUT SYSTEM OPERATION AND SERVICE MANUAL TABLE OF CONTENTS SYSTEM...... 3 Warning...... 3 Description..... 3 Prior to Operation... 4 4 OPERATION... Main

More information

Instruction Manual. Single Acting Hydraulic Aluminium Pull Cylinders RAP Series. Maximum Operating Pressure 700 bar

Instruction Manual. Single Acting Hydraulic Aluminium Pull Cylinders RAP Series. Maximum Operating Pressure 700 bar Single Acting Hydraulic Aluminium Pull Cylinders RAP Series Maximum Operating Pressure 700 bar ABSOLUTE EQUIPMENT PTY LTD 2/186 Granite Street, GEEBUNG QLD 4034 Australia sales@absoluteequipment.com.au

More information

USER INSTRUCTIONS FOR OPERATION & MAINTENANCE 4068 Pneuma c / Hydraulic Installa on Tool

USER INSTRUCTIONS FOR OPERATION & MAINTENANCE 4068 Pneuma c / Hydraulic Installa on Tool Additional copies of this manual are available at: USER INSTRUCTIONS FOR OPERATION & MAINTENANCE 4068 Pneuma c / Hydraulic Installa on Tool 4068 Hydro-Pneumatic Blind Rivet Nut and Stud Installation Tool

More information

Quality Stainless Products DB-8000-XL Strut Compressor

Quality Stainless Products DB-8000-XL Strut Compressor Quality Stainless Products DB-8000-XL Strut Compressor Thank you for choosing Quality Stainless Products DB-8000-XL, Strut Compressor. In order to operate your new Strut Compressor safely, we suggest you

More information

SW14.5TI INTEGRAL HYDRAULIC FLANGE SPREADING WEDGE. Repair Manual INNOVATION IN ITS MOST FUNCTIONAL FORM

SW14.5TI INTEGRAL HYDRAULIC FLANGE SPREADING WEDGE. Repair Manual INNOVATION IN ITS MOST FUNCTIONAL FORM SW14.5TI INTEGRAL HYDRAULIC FLANGE SPREADING WEDGE Repair Manual info@equalizerinternational.com www.equalizerinternational.com INNOVATION IN ITS MOST FUNCTIONAL FORM INDEX SECTION CONTENTS PAGE NO. 1

More information

DK/CP DN PVC-U / PVC-C / PP-H / PVDF. Pneumatically actuated 2-way diaphragm valve

DK/CP DN PVC-U / PVC-C / PP-H / PVDF. Pneumatically actuated 2-way diaphragm valve PVC-U / PVC-C / PP-H / PVDF Pneumatically actuated 2-way diaphragm valve DK/CP DN 15 32 The new DK/CP diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids.

More information

Owners manual. Öhlins Superbike front fork FG 170

Owners manual. Öhlins Superbike front fork FG 170 Owners manual Öhlins Superbike front fork FG 0 Including: Setting up your fork Changing springs and seals Service the fork Trouble shooting Technical info Spare parts & tools Öhlins super bike front fork

More information

PRODUCT MANUAL 52ST (V.4.0) 52ST FS (V.4.0.F) RON-WPM ST/52STFS-Rev.3

PRODUCT MANUAL 52ST (V.4.0) 52ST FS (V.4.0.F) RON-WPM ST/52STFS-Rev.3 PRODUCT MANUAL 52ST (V.4.0) RON-WPM-710021-52ST/52STFS-Rev.3 52ST (V.4.0) p2 EXPLODED VIEW ITEM. 3 MODEL ST - PART No. 540406 ITEM. 3 MODEL ST FS - PART No. 540411 ITEM. 16 - PART No. 589111 ITEM. 15 -

More information

Features. Marathon SL TECHNICAL CHARACTERISTICS. Sliding bushes: made of friction free and wear free material.

Features. Marathon SL TECHNICAL CHARACTERISTICS. Sliding bushes: made of friction free and wear free material. Features TECHNICAL CHARACTERISTICS Fork with Ø30 mm legs with "Double Air" damping system. Adjustment of the air preload (positive air) on both legs. Adjustment of the rebound damping (negative air) on

More information

SERIES G3DB/AG3DB ELEVATOR

SERIES G3DB/AG3DB ELEVATOR TM INSTRUCTIONS AND PARTS LIST SERIES G3DB/AG3DB ELEVATOR WARNING This manual, and GENERAL INSTRUCTIONS MANUAL, CA-1, should be read thoroughly prior to pump installation, operation or maintenance. SRM00059

More information

PNEUMATIC ACTUATORS ASSEMBLY & MAINTENANCE PROCEDURES. Ref. Doc. MMMACTREGDRE English Rev.2 January 2012 ADA & ASR SERIES DOUBLE ACTING ACTUATOR ADA

PNEUMATIC ACTUATORS ASSEMBLY & MAINTENANCE PROCEDURES. Ref. Doc. MMMACTREGDRE English Rev.2 January 2012 ADA & ASR SERIES DOUBLE ACTING ACTUATOR ADA ADA & ASR SERIES SPRING RETURN ACTUATOR ASR DOUBLE ACTING ACTUATOR ADA - LCIE 05 AR 022 V R 1 REVIEW CONTROL PROCEDURE REF. DOC. MMMACTREGDRE Rev. Date Carried out by Approved Description 0 02-01-2006

More information

See page 59 for complete parts list for all kits.

See page 59 for complete parts list for all kits. ELECTRIC & BATTERY-POWERED KNOCKOUT KITS Gator Plus Battery-Powered Knockout Punch Driver Kits SPECIFICATIONS Weight (driver with battery only) Overall Length (ram retracted) Height Maximum Punch Force

More information

FRP Ball Valves INSTALLATION & MAINTENANCE MANUAL

FRP Ball Valves INSTALLATION & MAINTENANCE MANUAL FRP Ball Valves INSTALLATION & MAINTENANCE MANUAL FRP BALL VALVES TABLE OF CONTENTS MAINTENANCE AND INSTALLATION INSTRUCTIONS 1. 2. 2.1 2.2 2.3 2.4 GENERAL...Page 1 HANDLING...1 Receiving and Storing...1

More information

MOTOR SCM M2

MOTOR SCM M2 MOTOR SCM 025 108 M2 Sunfab SCM M2 is a range of robust axial piston motors especially suitable for winch-, slewing-, wheeland track drives. Sunfab SCM M2 is of the bent-axis type with spherical pistons.

More information

Installation, Operating and Maintenance Instructions Retractable Door / Art.-Nr.:

Installation, Operating and Maintenance Instructions Retractable Door / Art.-Nr.: Installation, Operating and Maintenance Instructions Retractable Door 06.2008 / Art.-Nr.: 1 818 024 ENGLISH CONTENTS PAGE 1 SAFETY REQUIREMENTS 3 1.1 Symbols and key words used 3 1.2 Designated use 3 1.3

More information

INSTRUCTIONS & MAINTENANCE SHEET MODULAR HAND PUMP WI700

INSTRUCTIONS & MAINTENANCE SHEET MODULAR HAND PUMP WI700 INSTRUCTIONS & MAINTENANCE SHEET MODULAR HAND PUMP WI700 LARZEP, S.A. LARZEP AUSTRALIA PTY. LTD. LARZEP AUSTRALIA PTY. LTD. Avenida Urtiaga, 6 139 Wedgewood Road, 49A Sustainable Avenue 48269 MALLABIA,

More information

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS SETTING TOOL FOR RIVKLE BLIND RIVET NUTS AND STUDS CONTENTS I TOOL DESCRIPTION... p 2 II ACCESSORIES... p 4 III TOOL USE... p 6 IV MAINTENANCE... p12 V TROUBLESHOTTING AND SOLUTIONS...

More information

Type 431, 433. Balanced bellows design. Type Cap H2. 18 Adjusting screw with bushing. 19 Lock nut. 16 Upper spring plate. 12 Spindle.

Type 431, 433. Balanced bellows design. Type Cap H2. 18 Adjusting screw with bushing. 19 Lock nut. 16 Upper spring plate. 12 Spindle. Balanced bellows design 40 Cap H2 18 Adjusting screw with bushing 19 Lock nut 16 Upper spring plate 12 Spindle 9 Bonnet 54 Spring 14 Split ring 17 Lower spring plate 55 Stud 56 Nut 8 Guide with bushing

More information

PNEUMATICALLY ACTUATED 2-WAY

PNEUMATICALLY ACTUATED 2-WAY 482 DN 25-65 The 482 diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal geometry of the body optimises fluid dynamic efficiency by increasing

More information

2¼ TONNE TROLLEY JACK

2¼ TONNE TROLLEY JACK 2¼ TONNE TROLLEY JACK Model No: CTJ2250LP PART NO: 7623070 OPERATING & MAINTENANCE INSTRUCTIONS GC01/12 INTRODUCTION Thank you for purchasing this CLARKE Trolley Jack. Before attempting to use this product,

More information

FireFox. FireFox The new one. FireFox The reliable one. FireFox The versatile one. FireFox The simple one. FireFox The fast one

FireFox. FireFox The new one. FireFox The reliable one. FireFox The versatile one. FireFox The simple one. FireFox The fast one FireFox Most blind rivet nut setting devices are lift-controlled, the others are setting force-controlled The FireFox from GESIPA represents a new generation of blind rivet nut setting device which allows

More information

Petrol Driven Water Pump. Model No. CD1-1 Part No OPERATING & MAINTENANCE INSTRUCTIONS

Petrol Driven Water Pump. Model No. CD1-1 Part No OPERATING & MAINTENANCE INSTRUCTIONS Petrol Driven Water Pump Model No. CD1-1 Part No. 7230034 OPERATING & MAINTENANCE INSTRUCTIONS Thank you for purchasing this Clarke CD1 petrol driven water pump. Before attempting to operate this pump

More information

485 - NC NO/DA DN

485 - NC NO/DA DN 485 - NC 285 - NO/DA DN 25-100 The 485/285 diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. The new internal geometry of the body optimises fluid dynamic

More information

Marzocchi Suspension D-Street 24" D-Street 24" Technical instructions

Marzocchi Suspension D-Street 24 D-Street 24 Technical instructions Technical instructions Exploded view - D-Street 24" 80 Rif. Code Quantity D-Street 24" 80 - Oil levels Position Oil type Quantity (cc) Right fork leg SAE 7,5-550013 185 Left fork leg SAE 7,5-550013 185

More information

ALFRA PRESS - overview

ALFRA PRESS - overview 70 ALFRA PRESS 71 ALFRA PRESS - overview ALFRA PRESS AP 250 ALFRA PRESS AP 400 Page 74 Page 78 Control cabinet housing, Control cabinet doors, Mounting panels Control cabinet housing, Control cabinet doors,

More information

SCM DIN. Other advantages:

SCM DIN. Other advantages: SCM 012-130 DIN SCM 012-130 DIN is a series of axial piston motors particularly suitable for mobile hydraulics. SCM 012130 DIN is of the bent-axis type with spherical pistons. Other advantages: The design

More information

Owners Manual Öhlins road & track front fork FG 43 Including:

Owners Manual Öhlins road & track front fork FG 43 Including: Owners Manual Öhlins road & track front fork FG 43 Including: Safety Adjusters Setting up your fork Changing springs Oil level adjustment Technical information Inspection & maintenance Service Tools 1

More information

2/2-way Angle-Seat Control Valve with stainless steel design for media up to +185ºC, DN15-65

2/2-way Angle-Seat Control Valve with stainless steel design for media up to +185ºC, DN15-65 2/2-way Angle-Seat Control Valve with stainless steel design for media up to +185ºC, DN15-65 Excellent combination of good control characteristic and high fl ow rates High cycle life Clean design for optimal

More information

LAND ROVER DISCOVERY 3/ SPARE WHEEL CARRIER

LAND ROVER DISCOVERY 3/ SPARE WHEEL CARRIER LAND ROVER DISCOVERY 3/ 4 SPARE WHEEL CARRIER RBLD007 INSTALL TIME: 4.5 Hours NOTE: Park Distance Control will be affected by this fitment and the customer should be informed. IMPORTANT WARNING! IT IS

More information

Instruction Manual. Maximum Operating Pressure 510 bar

Instruction Manual. Maximum Operating Pressure 510 bar Single Speed Diesel Power Unit Model HPD11 Maximum Operating Pressure 510 bar ABSOLUTE EQUIPMENT PTY LTD 2/186 Granite Street, GEEBUNG QLD 4034 Australia sales@absoluteequipment.com.au Phone: +61 7 3865

More information

SERVICE MANUAL. Koala

SERVICE MANUAL. Koala SERVICE MANUAL Koala US How to contact Permobil Permobil Inc. USA 6961 Eastgate Blvd. Lebanon, TN 37090 USA Phone: 800-736-0925 Fax: 800-231-3256 Email: info@permobilusa.com Head Office of the Permobil

More information

HYDRAULIC PALLET TRUCK. MODEL No: PTE550 PART Nos OPERATION & MAINTENANCE INSTRUCTIONS

HYDRAULIC PALLET TRUCK. MODEL No: PTE550 PART Nos OPERATION & MAINTENANCE INSTRUCTIONS HYDRAULIC PALLET TRUCK MODEL No: PTE550 PART Nos 7630171 OPERATION & MAINTENANCE INSTRUCTIONS 0604 Please read these instructions carefully before operating the truck Thank you for purchasing this CLARKE

More information

High torque stainless steel motors ADVANCED LINE. Stainless Steel Air Motors from 20 W / 0.03 Hp up to 1.2 kw / 1.6 Hp

High torque stainless steel motors ADVANCED LINE. Stainless Steel Air Motors from 20 W / 0.03 Hp up to 1.2 kw / 1.6 Hp Screwdriving technology Automation Air motors Air tools ADVANCED LINE Stainless Steel Air s from 20 W / 0.03 Hp up to 1.2 kw / 1.6 Hp NEW MOTOR RANGE High torque motors made from stainless steel: Our ADVANCED

More information

MOREHOUSE INSTRUMENT COMPANY, INC. 60,000 LBS CAPACITY AIRCRAFT PART NUMBER SCALE S FORCE CALIBRATION PRESS PART NO.

MOREHOUSE INSTRUMENT COMPANY, INC. 60,000 LBS CAPACITY AIRCRAFT PART NUMBER SCALE S FORCE CALIBRATION PRESS PART NO. INDEX 1. GENERAL SPECIFICATION AND DRAWING 804000-03... 2 2. ASSEMBLY INSTRUCTIONS... 5 3. OPERATING INSTRUCTIONS... 6 4. MAINTENANCE INSTRUCTIONS... 7 5. CERTIFICATE OF CAPACITY LOAD TEST AND OVERLOAD...

More information

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 1980-1987 GENERAL MOTORS G BODY DISC SPINDLE PART NUMBER GROUP -508-B WARNING INSTALLATION OF THIS KIT SHOULD ONLY

More information

AVK SERIES 854 BALL FLOAT VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR BALL FLOAT VALVES

AVK SERIES 854 BALL FLOAT VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR BALL FLOAT VALVES AVK SERIES 854 BALL FLOAT VALVE FIELD MAINTENANCE AND INSTRUCTION MANUAL FOR BALL FLOAT VALVES TABLE OF CONTENTS GENERAL SERIES 854(TYPICAL EXPLODED VIEW) COMPONENT LIST INTRODUCTION TO AVK/GLENFIELD SERIES

More information

ASSEMBLY & OPERATION INSTRUCTION MANUAL

ASSEMBLY & OPERATION INSTRUCTION MANUAL Sliding Bridge Jack 3,500 lbs. Capacity ASSEMBLY & OPERATION INSTRUCTION MANUAL TABLE OF CONTENTS Specifications... 2 Description & Features... 3 Installation Instructions... 4 Safety Instructions... 4

More information

Filtrec elements are tested according to ISO 2941, ISO 2942 and ISO 23181

Filtrec elements are tested according to ISO 2941, ISO 2942 and ISO 23181 Common HYDRAULIC FILTRATION Side wall mounting suction filters Technical Information Connection Ports: 1-1 1/4-1 1/2 BSP (other thread options on request) 1 1/2 SAE J518-3000/M12 Housing Materials: Cover:

More information

x 10 Belt Disc Sander

x 10 Belt Disc Sander Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate

More information

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation. 2/2-Way Solenoid Valve 2/2-Wege-Magnetventil Électrovanne à 2/2 voies

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation. 2/2-Way Solenoid Valve 2/2-Wege-Magnetventil Électrovanne à 2/2 voies Type 5282 2/2-Way Solenoid Valve 2/2-Wege-Magnetventil Électrovanne à 2/2 voies Operating Instructions Bedienungsanleitung Manuel d utilisation 1 OPERATING INSTRUCTIONS The operating instructions contain

More information

Mounting and Operating Instructions EB 8222 EN. Type 3310/AT and Type 3310/3278 Pneumatic Control Valves. Type 3310 Segmented Ball Valve

Mounting and Operating Instructions EB 8222 EN. Type 3310/AT and Type 3310/3278 Pneumatic Control Valves. Type 3310 Segmented Ball Valve Type 3310/AT and Type 3310/3278 Pneumatic Control Valves Type 3310 Segmented Ball Valve Fig. 1 Type 3310/3278 with positioner Fig. 2 Type 3310/AT Mounting and Operating Instructions EB 8222 EN Edition

More information

4069 Operating Instructions

4069 Operating Instructions 4069 Operating Instructions SETTING TOOL FOR RIVKLE BLIND RIVET NUTS AND STUDS CONTENTS I TOOL DESCRIPTION... p 2 II ACCESSORIES... p 4 III TOOL USE... p 6 IV MAINTENANCE... p12 V TROUBLESHOTTING AND SOLUTIONS...

More information

Performa Winch 50.2 STP

Performa Winch 50.2 STP MRPW-03 Performa Winch 50.2 STP Index Introduction 3 Technical characteristics 3 Weight 3 Maximum working load 3 Outline 3 Installation 4 Installation procedure 6 Positioning the self-tailing arm 7 Maintenance

More information

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation. 2/2-Way Solenoid Valve 2/2-Wege-Magnetventil Électrovanne à 2/2 voies

Type Operating Instructions. Bedienungsanleitung Manuel d utilisation. 2/2-Way Solenoid Valve 2/2-Wege-Magnetventil Électrovanne à 2/2 voies Type 5282 2/2-Way Solenoid Valve 2/2-Wege-Magnetventil Électrovanne à 2/2 voies Operating Instructions Bedienungsanleitung Manuel d utilisation Contents 1 Operating Instructions... 2 2 Authorized use...

More information

VARIFUEL MAINTENANCE AND REPAIR INSTRUCTIONS

VARIFUEL MAINTENANCE AND REPAIR INSTRUCTIONS VARIFUEL2 140-65 MAINTENANCE AND REPAIR INSTRUCTIONS MOTORTECH Gas Regulation P/N 01.50.008-140-65-EN Rev. 06/2015 Copyright Copyright 2015 MOTORTECH GmbH. All rights reserved. Distribution and reproduction

More information

3-Stage Under Axle Jack Weight: 69.5 kg (153 lbs.)

3-Stage Under Axle Jack Weight: 69.5 kg (153 lbs.) 655 Eisenhower Drive Owatonna, MN 55060-0995 USA Phone: (507) 455-7000 Tech. Serv.: (00) 533-627 Fax: (00) 955-329 Order Entry: (00) 533-627 Fax: (00) 23-665 International Sales: (507) 455-7223 Fax: (507)

More information

SITEMA PowerStroke. Technical Information TI-P12. 1 Function. 2 Applications. Mould Closing Devices series FSKP. Contents. Technical Information

SITEMA PowerStroke. Technical Information TI-P12. 1 Function. 2 Applications. Mould Closing Devices series FSKP. Contents. Technical Information Technical Information SITEMA PowerStroke FSP ocking, actuating and releasing by pneumatic pressure TI-P1-EN-0/016 English translation of German original Technical Information TI-P1 SITEMA PowerStroke Mould

More information

AIR-SUSPENSION. Art. nr.: L.DOBLO.CM. Auxiliary Air Suspension. Designed for: Fiat Doblo. From: 2001 & UP RDW 71/

AIR-SUSPENSION. Art. nr.: L.DOBLO.CM. Auxiliary Air Suspension. Designed for: Fiat Doblo. From: 2001 & UP RDW 71/ AIR-SUSPENSION Dunlop Systems and Components Het Wegdam 22 7496 CA Hengevelde The Netherlands Tel.: +31-547-333065 Fax: +31-547-333068 Website: www.dunlopsystems.com Art. nr.: L.DOBLO.CM Designed for:

More information