1 of 7 7/22/2013 8:41 AM

Size: px

Start display at page:

Download "1 of 7 7/22/2013 8:41 AM"

Dinah Hill
5 years ago
Views:

1 1 of 7 7/22/2013 8:41 AM REMOVAL 1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead. 2. Turn the ignition switch to "LOCK". 3. Disconnect the battery "-" terminal cable, and wait at least 5 minutes. 4. Disconnect the yellow 2-way SRS connector located under the steering column. CAUTION: The wheels of the vehicle must be straight ahead and the steering column in the "LOCK" position before disconnecting the steering wheel. Failure to do so will cause the coil assembly to become uncentered which will cause damage to the coil assembly. 5. Remove the engine hood opening lever and steering lower cover. 6. Remove driver knee bolster (reinforcement).

2 2 of 7 7/22/2013 8:41 AM 7. Loosen the inflator module fixing bolt from behind the steering wheel assembly using a TORX driver or equivalent until the inflator module can be released from steering assembly. 8. Disconnect the yellow 2-way SRS connector located behind the inflator module.

3 gnition Switch Lock Cylinder Service and Repair, Procedures of 7 7/22/2013 8:41 AM 9. Apply a setting mark (1) across the steering wheel and shaft so parts can be reassembled in their original position. 10. Move the front wheels to the straight ahead position, then use steering wheel remover J to remove the steering wheel. CAUTION: Never apply force to the steering wheel in direction of the shaft by using a hammer or other impact tools in an attempt to remove the steering wheel. The steering shaft is designed as an energy absorbing unit.

4 4 of 7 7/22/2013 8:41 AM WARNING: The inflator module should always be carried with the urethane cover away from your body and should always be laid on a flat surface with the urethane side up. This is necessary because a free space is provided to allow the air cushion to expand in the unlikely event of accidental deployment. Otherwise, personal injury may result. 11. Remove steering column cover. 12. Disconnect the wiring harness connectors located under the steering column. 13. Remove the combination switch assembly with SRS coil. NOTE: The SRS coil is a part of the combination switch assembly, which can not be replaced separately. Therefore, be

5 5 of 7 7/22/2013 8:41 AM sure not to remove the SRS coil from the combination switch assembly. 14. Remove snap ring. 15. Remove cushion rubber. 16. Remove shift lock cable (for A/T). 17. Disconnect the starter switch harness connector located under the steering column then remove lock cylinder assembly. INSTALLATION 1. Install lock cylinder assembly. 2. install shift lock cable (for A/T). 3. Install cushion rubber. 4. Install snap ring. 5. Install Combination switch and SRS coil assembly. After installation of combination switch assembly, connect the combination switch wiring harness connector and the SRS 2-way connector located under the steering column. 6. Turn the SRS coil counter clockwise to full, return about 3 turns and align the neutral mark. CAUTION: When turning the SRS coil counter clockwise to full, stop turning if resistance is felt. Forced further turning may damage the cable in the SRS coil.

6 6 of 7 7/22/2013 8:41 AM 7. When installing the steering column cover, be sure to wire (through each harness) as illustrated so that the harnesses starter switch, combination switch and SRS coil may not catch wiring. 8. Install steering wheel by aligning the setting marks made during removal. CAUTION: Never apply force to the steering wheel in direction of the shaft by using a hammer or other impact tools in an attempt to remove the steering wheel. The steering shaft is designed as an energy absorbing unit. 9. Tighten the steering wheel fixing nut to the specified torque. Torque to 34 Nm (25 ft. lbs.). 10. Support inflator module and carefully connect the module connector, then install inflator module. NOTE: Pass the lead wire through the tabs on the plastic cover (wire protector) of inflator to prevent lead wire from being pinched. 11. Secure the inflator module with one bolt to relieve weight on the wire connector.

7 7 of 7 7/22/2013 8:41 AM 12. Tighten fixing bolts to specified sequence as illustrated. Torque to 8 Nm (69 inch lbs.). 13. Install driver knee bolster (reinforcement). 14. Install steering lower cover, then install the engine hood opening lever. 15. Connect the yellow 2-way SRS connector located under the steering column. 16. Connect the battery "-" terminal cable ALLDATA, LLC. All Rights Reserved. (Version )

ALLDATA Online Chevy Truck Avalanche WD V8-5.3L VIN T - Steering... Page 1 of 12. Steering Wheel Module Coil Replacement (Coil)

ALLDATA Online Chevy Truck Avalanche WD V8-5.3L VIN T - Steering... Page 1 of 12. Steering Wheel Module Coil Replacement (Coil) ALLDATA Online - 2006 Chevy Truck Avalanche 1500 2WD V8-5.3L VIN T - Steering... Page 1 of 12 Steering Wheel Module Coil Replacement (Coil) INFLATABLE RESTRAINT STEERING WHEEL MODULE COIL REPLACEMENT (COIL)